[PATCH v4 1/2] apic: Fix error interrupt report at all APs

[Youquan Song <youquan.song@intel.com>]

Recently, customer report that once machine boot, there are many error interrupt
reported with exact number of all APs. 

The root cause is Local APIC will generate error interrupt when it detect
the illegal vector (one in 0 ~ 15) in an interrupt message received or
interrupt generate from local vector table or self IPI. SDM3A.chapter 10.

AP LAPIC thermal sensor register will be reset to 0x10000, if thermal throttling
interrupt take over by BIOS, it need restore AP with the thermal sensor register
value of geting from BSP, otherwise cause system issue. If BIOS does not take
over the thermal interrupt, The restore value will be CPU rest value of 0x10000,
which means the interrupt vector is zero. After writing 0x10000 to thermal
sensor LVT, the processor will recieve the error interrupt report if the APIC
error interrupt is also set.

This patch add check the BIOS whether take over the thermal interrupt by look
at interrupt delivery mode not fixed mode(BIOS handle will be SMI mode) before
restore AP's thermal LVT. So the agony noise of error interrupt will dismiss
when boot on machine that BIOS does not handle thermal interrupt..  


Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
---
 arch/x86/include/asm/apicdef.h           |    1 +
 arch/x86/kernel/cpu/mcheck/therm_throt.c |   12 +++++++-----
 2 files changed, 8 insertions(+), 5 deletions(-)

diff --git a/arch/x86/include/asm/apicdef.h b/arch/x86/include/asm/apicdef.h
index d87988b..34595d5 100644
--- a/arch/x86/include/asm/apicdef.h
+++ b/arch/x86/include/asm/apicdef.h
@@ -78,6 +78,7 @@
 #define		APIC_DEST_LOGICAL	0x00800
 #define		APIC_DEST_PHYSICAL	0x00000
 #define		APIC_DM_FIXED		0x00000
+#define		APIC_DM_FIXED_MASK	0x00700
 #define		APIC_DM_LOWEST		0x00100
 #define		APIC_DM_SMI		0x00200
 #define		APIC_DM_REMRD		0x00300
diff --git a/arch/x86/kernel/cpu/mcheck/therm_throt.c b/arch/x86/kernel/cpu/mcheck/therm_throt.c
index 6f8c5e9..22c212a 100644
--- a/arch/x86/kernel/cpu/mcheck/therm_throt.c
+++ b/arch/x86/kernel/cpu/mcheck/therm_throt.c
@@ -446,18 +446,20 @@ void intel_init_thermal(struct cpuinfo_x86 *c)
 	 */
 	rdmsr(MSR_IA32_MISC_ENABLE, l, h);
 
+	h = lvtthmr_init;
 	/*
 	 * The initial value of thermal LVT entries on all APs always reads
 	 * 0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
 	 * sequence to them and LVT registers are reset to 0s except for
 	 * the mask bits which are set to 1s when APs receive INIT IPI.
-	 * Always restore the value that BIOS has programmed on AP based on
-	 * BSP's info we saved since BIOS is always setting the same value
-	 * for all threads/cores
+	 * If BIOS take over the thermal interrupt and set its interrupt
+	 * delivery mode to SMI not fixed, it restore the value that BIOS has
+	 * programmed on AP based on BSP's info we saved since BIOS is always
+	 * setting the same value for all threads/cores.
 	 */
-	apic_write(APIC_LVTTHMR, lvtthmr_init);
+	if ((h & APIC_DM_FIXED_MASK) != APIC_DM_FIXED)
+		apic_write(APIC_LVTTHMR, lvtthmr_init);
 
-	h = lvtthmr_init;
 
 	if ((l & MSR_IA32_MISC_ENABLE_TM1) && (h & APIC_DM_SMI)) {
 		printk(KERN_DEBUG
-- 
1.6.4.2