[U-Boot] [PATCH v2 10/16] ARM: remove broken "voiceblue" board

[Wolfgang Denk <wd@denx.de>]

Signed-off-by: Wolfgang Denk <wd@denx.de>
---
 MAKEALL                     |    1 -
 board/voiceblue/Makefile    |   74 -----------
 board/voiceblue/config.mk   |    1 -
 board/voiceblue/eeprom.c    |  218 ---------------------------------
 board/voiceblue/setup.S     |  280 -------------------------------------------
 board/voiceblue/voiceblue.c |   80 ------------
 boards.cfg                  |    1 -
 doc/README.scrapyard        |    1 +
 include/configs/voiceblue.h |  241 -------------------------------------
 9 files changed, 1 insertions(+), 896 deletions(-)
 delete mode 100644 board/voiceblue/Makefile
 delete mode 100644 board/voiceblue/config.mk
 delete mode 100644 board/voiceblue/eeprom.c
 delete mode 100644 board/voiceblue/setup.S
 delete mode 100644 board/voiceblue/voiceblue.c
 delete mode 100644 include/configs/voiceblue.h

diff --git a/MAKEALL b/MAKEALL
index d6d04b7..b230ff1 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -346,7 +346,6 @@ LIST_ARM9="			\
 	spear320		\
 	spear600		\
 	VCMA9			\
-	voiceblue		\
 	davinci_dvevm		\
 	davinci_schmoogie	\
 	davinci_sffsdr		\
diff --git a/board/voiceblue/Makefile b/board/voiceblue/Makefile
deleted file mode 100644
index e16b195..0000000
--- a/board/voiceblue/Makefile
+++ /dev/null
@@ -1,74 +0,0 @@
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de
-#
-# (C) Copyright 2005
-# Ladislav Michl, 2N Telekomunikace, michl at 2n.cz
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or modify
-# it under the terms of the GNU General Public License version 2 as
-# published by the Free Software Foundation.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB	= $(obj)lib$(BOARD).o
-
-COBJS	:= voiceblue.o
-SOBJS	:= setup.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS))
-SOBJS	:= $(addprefix $(obj),$(SOBJS))
-
-LOAD_ADDR = 0x10400000
-
-#########################################################################
-
-all:	$(obj).depend $(LIB) $(obj)eeprom.srec $(obj)eeprom.bin
-
-$(LIB):	$(OBJS) $(SOBJS)
-	$(call cmd_link_o_target, $^)
-
-$(obj)eeprom_start.o:
-	echo "b eeprom" | $(CC) $(AFLAGS) -c -x assembler -o $@ -
-
-$(obj)eeprom:		$(obj)eeprom_start.o $(obj)eeprom.o
-	$(LD) -Ttext $(LOAD_ADDR) -e eeprom -o $@ $^ \
-		-L$(obj)../../examples/standalone -lstubs \
-		$(PLATFORM_LIBS)
-
-$(obj)eeprom.srec:	$(obj)eeprom
-	$(OBJCOPY) -S -O srec $(<:.o=) $@
-
-$(obj)eeprom.bin:	$(obj)eeprom
-	$(OBJCOPY) -S -O binary $< $@
-
-clean:
-	rm -f $(SOBJS) $(OBJS) $(obj)eeprom \
-		$(obj)eeprom.srec $(obj)eeprom.bin \
-		$(obj)eeprom.o $(obj)eeprom_start.o
-
-distclean:	clean
-	rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/voiceblue/config.mk b/board/voiceblue/config.mk
deleted file mode 100644
index 412b57d..0000000
--- a/board/voiceblue/config.mk
+++ /dev/null
@@ -1 +0,0 @@
-CONFIG_SYS_TEXT_BASE = 0x13FD0000
diff --git a/board/voiceblue/eeprom.c b/board/voiceblue/eeprom.c
deleted file mode 100644
index aa6baca..0000000
--- a/board/voiceblue/eeprom.c
+++ /dev/null
@@ -1,218 +0,0 @@
-/*
- * (C) Copyright 2005
- * Ladislav Michl, 2N Telekomunikace, michl@2n.cz
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * Some code shamelessly stolen back from Robin Getz.
- */
-
-#include <common.h>
-#include <exports.h>
-#include <timestamp.h>
-#include <net.h>
-#include "../drivers/net/smc91111.h"
-
-static struct eth_device dev = {
-	.iobase = CONFIG_SMC91111_BASE
-};
-
-static u16 read_eeprom_reg(u16 reg)
-{
-	int timeout;
-
-	SMC_SELECT_BANK(&dev, 2);
-	SMC_outw(&dev, reg, PTR_REG);
-
-	SMC_SELECT_BANK(&dev, 1);
-	SMC_outw(&dev, SMC_inw(&dev, CTL_REG) | CTL_EEPROM_SELECT |
-		CTL_RELOAD, CTL_REG);
-
-	timeout = 100;
-
-	while ((SMC_inw(&dev, CTL_REG) & CTL_RELOAD) && --timeout)
-		udelay(100);
-	if (timeout == 0) {
-		printf("Timeout reading register %02x\n", reg);
-		return 0;
-	}
-
-	return SMC_inw(&dev, GP_REG);
-}
-
-static int write_eeprom_reg(u16 value, u16 reg)
-{
-	int timeout;
-
-	SMC_SELECT_BANK(&dev, 2);
-	SMC_outw(&dev, reg, PTR_REG);
-
-	SMC_SELECT_BANK(&dev, 1);
-
-	SMC_outw(&dev, value, GP_REG);
-	SMC_outw(&dev, SMC_inw(&dev, CTL_REG) | CTL_EEPROM_SELECT |
-		CTL_STORE, CTL_REG);
-
-	timeout = 100;
-
-	while ((SMC_inw(&dev, CTL_REG) & CTL_STORE) && --timeout)
-		udelay(100);
-	if (timeout == 0) {
-		printf("Timeout writing register %02x\n", reg);
-		return 0;
-	}
-
-	return 1;
-}
-
-static int write_data(u16 *buf, int len)
-{
-	u16 reg = 0x23;
-
-	while (len--)
-		write_eeprom_reg(*buf++, reg++);
-
-	return 0;
-}
-
-static int verify_macaddr(char *s)
-{
-	u16 reg;
-	int i, err = 0;
-
-	puts("HWaddr: ");
-	for (i = 0; i < 3; i++) {
-		reg = read_eeprom_reg(0x20 + i);
-		printf("%02x:%02x%c", reg & 0xff, reg >> 8, i != 2 ? ':' : '\n');
-		if (s)
-			err |= reg != ((u16 *)s)[i];
-	}
-
-	return err ? 0 : 1;
-}
-
-static int set_mac(char *s)
-{
-	int i;
-	char *e, eaddr[6];
-
-	/* turn string into mac value */
-	for (i = 0; i < 6; i++) {
-		eaddr[i] = simple_strtoul(s, &e, 16);
-		s = (*e) ? e+1 : e;
-	}
-
-	for (i = 0; i < 3; i++)
-		write_eeprom_reg(*(((u16 *)eaddr) + i), 0x20 + i);
-
-	return 0;
-}
-
-static int parse_element(char *s, unsigned char *buf, int len)
-{
-	int cnt;
-	char *p, num[3];
-	unsigned char id;
-
-	id = simple_strtoul(s, &p, 16);
-	if (*p++ != ':')
-		return -1;
-	cnt = 2;
-	num[2] = 0;
-	for (; *p; p += 2) {
-		if (p[1] == 0)
-			return -2;
-		if (cnt + 3 > len)
-			return -3;
-		num[0] = p[0];
-		num[1] = p[1];
-		buf[cnt++] = simple_strtoul(num, NULL, 16);
-	}
-	buf[0] = id;
-	buf[1] = cnt - 2;
-
-	return cnt;
-}
-
-int eeprom(int argc, char * const argv[])
-{
-	int i, len, ret;
-	unsigned char buf[58], *p;
-
-	app_startup(argv);
-	i = get_version();
-	if (i != XF_VERSION) {
-		printf("Using ABI version %d, but U-Boot provides %d\n",
-			XF_VERSION, i);
-		return 1;
-	}
-
-	if ((SMC_inw(&dev, BANK_SELECT) & 0xFF00) != 0x3300) {
-		puts("SMSC91111 not found\n");
-		return 2;
-	}
-
-	/* Called without parameters - print MAC address */
-	if (argc < 2) {
-		verify_macaddr(NULL);
-		return 0;
-	}
-
-	/* Print help message */
-	if (argv[1][1] == 'h') {
-		puts("VoiceBlue EEPROM writer\n"
-			"Built: " U_BOOT_DATE "@" U_BOOT_TIME "\n"
-			"Usage:\n\t<mac_address> [<element_1>] [<...>]\n");
-		return 0;
-	}
-
-	/* Try to parse information elements */
-	len = sizeof(buf);
-	p = buf;
-	for (i = 2; i < argc; i++) {
-		ret = parse_element(argv[i], p, len);
-		switch (ret) {
-		case -1:
-			printf("Element %d: malformed\n", i - 1);
-			return 3;
-		case -2:
-			printf("Element %d: odd character count\n", i - 1);
-			return 3;
-		case -3:
-			puts("Out of EEPROM memory\n");
-			return 3;
-		default:
-			p += ret;
-			len -= ret;
-		}
-	}
-
-	/* First argument (MAC) is mandatory */
-	set_mac(argv[1]);
-	if (verify_macaddr(argv[1])) {
-		puts("*** HWaddr does not match! ***\n");
-		return 4;
-	}
-
-	while (len--)
-		*p++ = 0;
-
-	write_data((u16 *)buf, sizeof(buf) >> 1);
-
-	return 0;
-}
diff --git a/board/voiceblue/setup.S b/board/voiceblue/setup.S
deleted file mode 100644
index 6dddd6b..0000000
--- a/board/voiceblue/setup.S
+++ /dev/null
@@ -1,280 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2004 Ales Jindra <jindra@2n.cz>
- * (C) Copyright 2005 Ladislav Michl <michl@2n.cz>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <config.h>
-#include <version.h>
-
-_TEXT_BASE:
-	.word	CONFIG_SYS_TEXT_BASE	/* SDRAM load addr from config.mk */
-
-OMAP5910_LPG1_BASE:		.word 0xfffbd000
-OMAP5910_TIPB_SWITCHES_BASE:	.word 0xfffbc800
-OMAP5910_MPU_TC_BASE:		.word 0xfffecc00
-OMAP5910_MPU_CLKM_BASE:		.word 0xfffece00
-OMAP5910_ULPD_PWR_MNG_BASE:	.word 0xfffe0800
-OMAP5910_DPLL1_BASE:		.word 0xfffecf00
-OMAP5910_GPIO_BASE:		.word 0xfffce000
-OMAP5910_MPU_WD_TIMER_BASE:	.word 0xfffec800
-OMAP5910_MPUI_BASE:		.word 0xfffec900
-
-_OMAP5910_ARM_CKCTL:		.word OMAP5910_ARM_CKCTL
-_OMAP5910_ARM_EN_CLK:		.word OMAP5910_ARM_EN_CLK
-
-OMAP5910_MPUI_CTRL:		.word 0x0000ff1b
-
-VAL_EMIFS_CS0_CONFIG:		.word 0x00009090
-VAL_EMIFS_CS1_CONFIG:		.word 0x00003031
-VAL_EMIFS_CS2_CONFIG:		.word 0x00003031
-VAL_EMIFS_CS3_CONFIG:		.word 0x0000c0c0
-VAL_EMIFS_DYN_WAIT:		.word 0x00000000
-/* autorefresh counter 0x246 ((64000000/13.4)-400)/8192) */
-				/*     SLRF       SD_RET     ARE        SDRAM_TYPE   ARCV           SDRAM_FREQUENCY PWD     CLK */
-VAL_EMIFF_SDRAM_CONFIG:		.word ((0 << 0) | (0 << 1) | (3 << 2) | (0xd << 4) | (0x246 << 8) | (0 << 24) | (0 << 26) | (0 << 27))
-VAL_EMIFF_SDRAM_CONFIG2:	.word 0x00000003
-VAL_EMIFF_MRS:			.word 0x00000037
-
-/*
- * GPIO04 - D4 (Onboard LED)
- * GPIO07 - LAN91C111 reset
- */
-GPIO_DIRECTION:
-	.word 0x0000ff6f
-/*
- * Disable everything, but D4 LED (connected through invertor)
- */
-GPIO_OUTPUT:
-	.word 0x00000010
-
-MUX_CONFIG_BASE:
-	.word 0xfffe1000
-
-MUX_CONFIG_VALUES:
-	.align 4
-	.word 0x00000000	@ FUNC_MUX_CTRL_0
-	.word 0x00000000	@ FUNC_MUX_CTRL_1
-	.word 0x00000000	@ FUNC_MUX_CTRL_2
-	.word 0x00000000	@ FUNC_MUX_CTRL_3
-	.word 0x00000000	@ FUNC_MUX_CTRL_4
-	.word 0x12082480	@ FUNC_MUX_CTRL_5
-	.word 0x0000001c	@ FUNC_MUX_CTRL_6
-	.word 0x00000003	@ FUNC_MUX_CTRL_7
-	.word 0x10001200	@ FUNC_MUX_CTRL_8
-	.word 0x01201012	@ FUNC_MUX_CTRL_9
-	.word 0x02081248	@ FUNC_MUX_CTRL_A
-	.word 0x00001248	@ FUNC_MUX_CTRL_B
-	.word 0x12240000	@ FUNC_MUX_CTRL_C
-	.word 0x00002000	@ FUNC_MUX_CTRL_D
-	.word 0x00000000	@ PULL_DWN_CTRL_0
-	.word 0x0000085f	@ PULL_DWN_CTRL_1
-	.word 0x01001000	@ PULL_DWN_CTRL_2
-	.word 0x00000000	@ PULL_DWN_CTRL_3
-	.word 0x00000000	@ GATE_INH_CTRL_0
-	.word 0x00000000	@ VOLTAGE_CTRL_0
-	.word 0x00000000	@ TEST_DBG_CTRL_0
-	.word 0x00000006	@ MOD_CONF_CTRL_0
-	.word 0x0000eaef	@ COMP_MODE_CTRL_0
-
-MUX_CONFIG_OFFSETS:
-	.align 1
-	.byte 0x00		@ FUNC_MUX_CTRL_0
-	.byte 0x04		@ FUNC_MUX_CTRL_1
-	.byte 0x08		@ FUNC_MUX_CTRL_2
-	.byte 0x10		@ FUNC_MUX_CTRL_3
-	.byte 0x14		@ FUNC_MUX_CTRL_4
-	.byte 0x18		@ FUNC_MUX_CTRL_5
-	.byte 0x1c		@ FUNC_MUX_CTRL_6
-	.byte 0x20		@ FUNC_MUX_CTRL_7
-	.byte 0x24		@ FUNC_MUX_CTRL_8
-	.byte 0x28		@ FUNC_MUX_CTRL_9
-	.byte 0x2c		@ FUNC_MUX_CTRL_A
-	.byte 0x30		@ FUNC_MUX_CTRL_B
-	.byte 0x34		@ FUNC_MUX_CTRL_C
-	.byte 0x38		@ FUNC_MUX_CTRL_D
-	.byte 0x40		@ PULL_DWN_CTRL_0
-	.byte 0x44		@ PULL_DWN_CTRL_1
-	.byte 0x48		@ PULL_DWN_CTRL_2
-	.byte 0x4c		@ PULL_DWN_CTRL_3
-	.byte 0x50		@ GATE_INH_CTRL_0
-	.byte 0x60		@ VOLTAGE_CTRL_0
-	.byte 0x70		@ TEST_DBG_CTRL_0
-	.byte 0x80		@ MOD_CONF_CTRL_0
-	.byte 0x0c		@ COMP_MODE_CTRL_0
-	.byte 0xff
-
-.globl lowlevel_init
-lowlevel_init:
-	/* Improve performance a bit... */
-	mrc	p15, 0, r1, c0, c0, 0		@ read C15 ID register
-	mrc	p15, 0, r1, c0, c0, 1		@ read C15 Cache information register
-	mrc	p15, 0, r1, c1, c0, 0		@ read C15 Control register
-	orr	r1, r1, #0x1000			@ enable I-cache, map interrupt vector 0xffff0000
-	mcr	p15, 0, r1, c1, c0, 0		@ write C15 Control register
-	mov	r1, #0x00
-	mcr	p15, 0, r1, c7, c5, 0		@ Flush I-cache
-	nop
-	nop
-	nop
-	nop
-
-	/* Setup clocking mode */
-	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ prepare base of CLOCK unit
-	ldrh	r1, [r0, #0x18]			@ get reset status
-	bic	r1, r1, #(7 << 11)		@ clear clock select
-	orr	r1, r1, #(2 << 11)		@ set synchronous scalable
-	mov	r2, #0				@ set wait counter to 100 clock cycles
-
-icache_loop:
-	cmp	r2, #0x01
-	streqh	r1, [r0, #0x18]
-	add	r2, r2, #0x01
-	cmp	r2, #0x10
-	bne	icache_loop
-	nop
-
-	/* Setup clock divisors */
-	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ base of CLOCK unit
-	ldr	r1, _OMAP5910_ARM_CKCTL
-	orr	r1, r1, #0x2000			@ enable DSP clock
-	strh	r1, [r0, #0x00]			@ setup clock divisors
-
-	/* Setup DPLL to generate requested freq */
-	ldr	r0, OMAP5910_DPLL1_BASE		@ base of DPLL1 register
-	mov	r1, #0x0010			@ set PLL_ENABLE
-	orr	r1, r1, #0x2000			@ set IOB to new locking
-	orr	r1, r1, #(OMAP5910_DPLL_MUL << 7) @ setup multiplier CLKREF
-	orr	r1, r1, #(OMAP5910_DPLL_DIV << 5) @ setup divider CLKREF
-	strh	r1, [r0]			@ write
-
-locking:
-	ldrh	r1, [r0]			@ get DPLL value
-	tst	r1, #0x01
-	beq	locking				@ while LOCK not set
-
-	/* Enable clock */
-	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ base of CLOCK unit
-	mov	r1, #(1 << 10)			@ disable idle mode do not check
-						@ nWAKEUP pin, other remain active
-	strh	r1, [r0, #0x04]
-	ldr	r1, _OMAP5910_ARM_EN_CLK
-	strh	r1, [r0, #0x08]
-	mov	r1, #0x003f			@ FLASH.RP not enabled in idle and
-						@ max delayed ( 32 x CLKIN )
-	strh	r1, [r0, #0x0c]
-
-	/* Configure 5910 pins functions to match our board. */
-	ldr     r0, MUX_CONFIG_BASE
-	adr	r1, MUX_CONFIG_VALUES
-	adr	r2, MUX_CONFIG_OFFSETS
-next_mux_cfg:
-	ldrb	r3, [r2], #1
-	ldr	r4, [r1], #4
-	cmp	r3, #0xff
-	strne	r4, [r0, r3]
-	bne	next_mux_cfg
-
-	/* Configure GPIO pins (also enables onboard LED) */
-	ldr	r0, OMAP5910_GPIO_BASE
-	ldr	r1, GPIO_OUTPUT
-	strh    r1, [r0, #0x04]
-	ldr	r1, GPIO_DIRECTION
-	strh	r1, [r0, #0x08]
-
-	/* EnablePeripherals */
-	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ CLOCK unit
-	mov	r1, #0x0001			@ Peripheral enable
-	strh	r1, [r0, #0x14]
-
-	/* Program LED Pulse Generator */
-	ldr	r0, OMAP5910_LPG1_BASE		@ 1st LED Pulse Generator
-	mov	r1, #0x7F			@ Set obscure frequency in
-	strb	r1, [r0, #0x00]			@ LCR
-	mov	r1, #0x01			@ Enable clock (CLK_EN) in
-	strb    r1, [r0, #0x04]			@ PMR
-
-	/* TIPB Lock UART1 */
-	ldr	r0, OMAP5910_TIPB_SWITCHES_BASE	@ prepare base of TIPB switches
-	mov	r1, #1				@ ARM allocated
-	strh	r1, [r0,#0x04]			@ clear IRQ line and status bits
-	strh	r1, [r0,#0x00]
-	ldrh	r1, [r0,#0x04]
-
-	/* Disable watchdog */
-	ldr	r0, OMAP5910_MPU_WD_TIMER_BASE
-	mov	r1, #0xf5
-	strh	r1, [r0, #0x8]
-	mov	r1, #0xa0
-	strh	r1, [r0, #0x8]
-
-	/* Enable MCLK */
-	ldr	r0, OMAP5910_ULPD_PWR_MNG_BASE
-	mov	r1, #0x6
-	strh	r1, [r0, #0x34]
-	strh	r1, [r0, #0x34]
-
-	/* Setup clock divisors */
-	ldr	r0, OMAP5910_ULPD_PWR_MNG_BASE	@ base of ULDPL DPLL1 register
-
-	mov	r1, #0x0010			@ set PLL_ENABLE
-	orr	r1, r1, #0x2000			@ set IOB to new locking
-	strh	r1, [r0]			@ write
-
-ulocking:
-	ldrh	r1, [r0]			@ get DPLL value
-	tst	r1, #1
-	beq	ulocking			@ while LOCK not set
-
-	/* EMIF init */
-	ldr	r0, OMAP5910_MPU_TC_BASE
-	ldrh	r1, [r0, #0x0c]			@ EMIFS_CONFIG_REG
-	bic	r1, r1, #0x0c			@ pwr down disabled, flash WP
-	orr	r1, r1, #0x01
-	str	r1, [r0, #0x0c]
-
-	ldr	r1, VAL_EMIFS_CS0_CONFIG
-	str	r1, [r0, #0x10]			@ EMIFS_CS0_CONFIG
-	ldr	r1, VAL_EMIFS_CS1_CONFIG
-	str	r1, [r0, #0x14]			@ EMIFS_CS1_CONFIG
-	ldr	r1, VAL_EMIFS_CS2_CONFIG
-	str	r1, [r0, #0x18]			@ EMIFS_CS2_CONFIG
-	ldr	r1, VAL_EMIFS_CS3_CONFIG
-	str	r1, [r0, #0x1c]			@ EMIFS_CS3_CONFIG
-	ldr	r1, VAL_EMIFS_DYN_WAIT
-	str	r1, [r0, #0x40]			@ EMIFS_CFG_DYN_WAIT
-
-	/* Setup SDRAM */
-	ldr	r1, VAL_EMIFF_SDRAM_CONFIG
-	str	r1, [r0, #0x20]			@ EMIFF_SDRAM_CONFIG
-	ldr	r1, VAL_EMIFF_SDRAM_CONFIG2
-	str	r1, [r0, #0x3c]			@ EMIFF_SDRAM_CONFIG2
-	ldr	r1, VAL_EMIFF_MRS
-	str	r1, [r0, #0x24]			@ EMIFF_MRS
-	/* SDRAM needs 100us to stabilize */
-	mov	r0, #0x4000
-sdelay:
-	subs	r0, r0, #0x1
-	bne	sdelay
-
-	/* back to arch calling code */
-	mov	pc, lr
-.end
diff --git a/board/voiceblue/voiceblue.c b/board/voiceblue/voiceblue.c
deleted file mode 100644
index 5f8af2b..0000000
--- a/board/voiceblue/voiceblue.c
+++ /dev/null
@@ -1,80 +0,0 @@
-/*
- * (C) Copyright 2005 2N TELEKOMUNIKACE, Ladislav Michl
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
-	*((volatile unsigned char *) VOICEBLUE_LED_REG) = 0xaa;
-
-	/* arch number of VoiceBlue board */
-	gd->bd->bi_arch_number = MACH_TYPE_VOICEBLUE;
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x10000100;
-
-	return 0;
-}
-
-int dram_init(void)
-{
-	*((volatile unsigned short *) VOICEBLUE_LED_REG) = 0xff;
-
-	/* Take the Ethernet controller out of reset and wait
-	 * for the EEPROM load to complete. */
-	*((volatile unsigned short *) GPIO_DATA_OUTPUT_REG) |= 0x80;
-	udelay(10);	/* doesn't work before timer_init call */
-	*((volatile unsigned short *) GPIO_DATA_OUTPUT_REG) &= ~0x80;
-	udelay(500);
-
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}
-
-int misc_init_r(void)
-{
-	*((volatile unsigned short *) VOICEBLUE_LED_REG) = 0x55;
-
-	return 0;
-}
-
-int board_late_init(void)
-{
-	*((volatile unsigned char *) VOICEBLUE_LED_REG) = 0x00;
-
-	return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-#ifdef CONFIG_SMC91111
-	rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
-	return rc;
-}
-#endif
diff --git a/boards.cfg b/boards.cfg
index f70afe2..b4d82db 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -68,7 +68,6 @@ cm4008                       arm         arm920t     -                   -
 cm41xx                       arm         arm920t     -                   -              ks8695
 VCMA9                        arm         arm920t     vcma9               mpl            s3c24x0
 smdk2410                     arm         arm920t     -                   samsung        s3c24x0
-voiceblue                    arm         arm925t
 omap1510inn                  arm         arm925t     -                   ti
 integratorap_cm926ejs        arm         arm926ejs   integrator          armltd         -           integratorap
 integratorcp_cm926ejs        arm         arm926ejs   integrator          armltd         -           integratorcp
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 087e0e1..144edaa 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -11,6 +11,7 @@ easily if here is something they might want to dig for...
 
 Board	Arch	CPU	removed	    Commit	last known maintainer/contact
 =============================================================================
+voiceblue arm	arm925t	-	  2011-07-17
 versatile arm	ARM926EJS -	  2011-07-17	Peter Pearse <peter.pearse@arm.com>
 smdk2400 arm	arm920t	-	  2011-07-17	Gary Jennejohn <garyj@denx.de>
 sbc2410x arm	arm920t	-	  2011-07-17
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
deleted file mode 100644
index c258030..0000000
--- a/include/configs/voiceblue.h
+++ /dev/null
@@ -1,241 +0,0 @@
-/*
- * (C) Copyright 2005 2N TELEKOMUNIKACE, Ladislav Michl
- *
- * Configuation settings for the TI OMAP VoiceBlue board.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <configs/omap1510.h>
-
-#define CONFIG_ARM925T	1		/* This is an arm925t CPU */
-#define CONFIG_OMAP	1		/* in a TI OMAP core */
-#define CONFIG_OMAP1510 1		/* which is in a 5910 */
-
-/* Input clock of PLL */
-#define CONFIG_SYS_CLK_FREQ		150000000	/* 150MHz */
-#define CONFIG_XTAL_FREQ		12000000	/*  12MHz */
-
-#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
-
-#define CONFIG_MISC_INIT_R		/* There is nothing to really init */
-#define BOARD_LATE_INIT			/* but we flash the LEDs here */
-
-#define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS	1
-#define CONFIG_INITRD_TAG		1
-
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
-
-/*
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS		1
-#define PHYS_SDRAM_1			0x10000000
-#define PHYS_SDRAM_1_SIZE		(64 * 1024 * 1024)
-#define PHYS_FLASH_1			0x0000000
-
-#define CONFIG_SYS_MONITOR_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR			(PHYS_FLASH_1 + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE			(8 * 1024)
-#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
-#define CONFIG_ENV_ADDR_REDUND		(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
-
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Size of malloc() pool and stack
- */
-#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
-#define CONFIG_STACKSIZE		(1 * 1024 * 1024)
-
-/*
- * Hardware drivers
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
-#define CONFIG_SYS_NS16550_CLK		(CONFIG_XTAL_FREQ)
-#define CONFIG_SYS_NS16550_COM1		OMAP1510_UART1_BASE
-
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111
-#define CONFIG_SMC91111_BASE		0x08000300
-
-#define CONFIG_SYS_FLASH_BASE		PHYS_FLASH_1
-#define CONFIG_SYS_MAX_FLASH_BANKS	1
-#define CONFIG_SYS_MAX_FLASH_SECT	512
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP1510_I2C
-
-#define CONFIG_RTC_DS1307
-#define CONFIG_SYS_I2C_RTC_ADDR		0x68
-
-
-#define CONFIG_CONS_INDEX		1
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
-
-/*
- * Command line configuration
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-
-#define CONFIG_LOOPW
-
-#define CONFIG_BOOTDELAY	3
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* allow to break in always */
-#undef  CONFIG_BOOTARGS			/* the boot command will set bootargs*/
-#define CONFIG_SYS_AUTOLOAD		"n"
-#define CONFIG_BOOTCOMMAND	"run nboot"
-#define CONFIG_PREBOOT		"run setup"
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"silent=1\0"							\
-	"ospart=0\0"							\
-	"bootfile=/boot/uImage\0"					\
-	"setpart="							\
-	"if test -n $swapos; then "					\
-		"setenv swapos; saveenv; "				\
-		"if test $ospart -eq 0; then "				\
-			"setenv ospart 1; "				\
-		"else "							\
-			"setenv ospart 0; "				\
-		"fi; "							\
-	"fi\0"								\
-	"setup=setenv bootargs console=ttyS0,$baudrate "		\
-		"mtdparts=$mtdparts\0"					\
-	"nfsargs=setenv bootargs $bootargs "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
-		"nfsroot=$rootpath root=/dev/nfs\0"			\
-	"flashargs=run setpart; setenv bootargs $bootargs "		\
-		"root=mtd:data$ospart ro "				\
-		"rootfstype=jffs2\0"					\
-	"initrdargs=setenv bootargs $bootargs "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
-	"fboot=run flashargs; chpart data$ospart; fsload; bootm\0"	\
-	"mboot=bootp; run initrdargs; tftp; bootm\0"			\
-	"nboot=bootp; run nfsargs; tftp; bootm\0"
-
-#define CONFIG_SILENT_CONSOLE		1	/* enable silent startup */
-
-#if 1	/* feel free to disable for development */
-#define CONFIG_AUTOBOOT_KEYED		/* Enable password protection	*/
-#define CONFIG_AUTOBOOT_PROMPT	"\nVoiceBlue Enterprise - booting...\n"
-#define CONFIG_AUTOBOOT_DELAY_STR	"."	/* 1st "password"	*/
-#endif
-
-/*
- * Partitions (mtdparts command line support)
- */
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
-#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT		"nor0=physmap-flash.0"
-#define MTDPARTS_DEFAULT	"mtdparts=physmap-flash.0:" \
-	"256k(u-boot),64k(env),64k(r_env),16192k(data0),-(data1)"
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT		"# "
-#define CONFIG_SYS_CBSIZE		256
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-					 sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS		16
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START	(PHYS_SDRAM_1)
-#define CONFIG_SYS_MEMTEST_END		(PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - \
-	(CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE))
-#define CONFIG_SYS_LOAD_ADDR		(PHYS_SDRAM_1 + 0x400000)
-
-/*
- * The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
- * This time is further subdivided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE		OMAP1510_TIMER1_BASE
-#define CONFIG_SYS_PTV			7	/* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ			1000
-
-#define OMAP5910_DPLL_DIV		1
-#define OMAP5910_DPLL_MUL		\
-	((CONFIG_SYS_CLK_FREQ * (1 << OMAP5910_DPLL_DIV)) / CONFIG_XTAL_FREQ)
-
-#define OMAP5910_ARM_PER_DIV	2	/* CKL/4 */
-#define OMAP5910_LCD_DIV	2	/* CKL/4 */
-#define OMAP5910_ARM_DIV	0	/* CKL/1 */
-#define OMAP5910_DSP_DIV	0	/* CKL/1 */
-#define OMAP5910_TC_DIV		1	/* CKL/2 */
-#define OMAP5910_DSP_MMU_DIV	1	/* CKL/2 */
-#define OMAP5910_ARM_TIM_SEL	1	/* CKL used for MPU timers */
-
-#define OMAP5910_ARM_EN_CLK	0x03d6	/* 0000 0011 1101 0110b  Clock Enable */
-#define OMAP5910_ARM_CKCTL	((OMAP5910_ARM_PER_DIV)  |	\
-				 (OMAP5910_LCD_DIV << 2) |	\
-				 (OMAP5910_ARM_DIV << 4) |	\
-				 (OMAP5910_DSP_DIV << 6) |	\
-				 (OMAP5910_TC_DIV << 8) |	\
-				 (OMAP5910_DSP_MMU_DIV << 10) |	\
-				 (OMAP5910_ARM_TIM_SEL << 12))
-
-#define VOICEBLUE_LED_REG	0x04030000
-
-#endif	/* __CONFIG_H */
-- 
1.7.6