* [PATCH 0/2] net: support for NS8390 based ethernet on ColdFire CPU boards
@ 2012-07-04 4:56 ` gerg
0 siblings, 0 replies; 14+ messages in thread
From: gerg @ 2012-07-04 4:56 UTC (permalink / raw)
To: netdev, linux-m68k
The following 2 patches add platform support for using the NS8390 based
ethernet ports used on some ColdFire CPU boards. Patches to use these
have existed out-of-tree for years. Some of the base IO definitions
(those in arch/m68k/include/asm/mcfne.h) have been in mainline, but unused
for most of that time.
The first patch just neatens up mcfne.h (moving it to mcf8390.h). The
second patch is the platform driver. The first patch would normaly just
go through the m68knommu git tree, but I figured keeping these together made
more sense.
---
arch/m68k/include/asm/mcf8390.h | 371 ++++++++++++++++++---------
arch/m68k/include/asm/mcfne.h | 242 ------------------
drivers/net/ethernet/8390/Kconfig | 14 +
drivers/net/ethernet/8390/Makefile | 1
drivers/net/ethernet/8390/mcf8390.c | 478 ++++++++++++++++++++++++++++++++++++
5 files changed, 744 insertions(+), 362 deletions(-)
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 0/2] net: support for NS8390 based ethernet on ColdFire CPU boards
@ 2012-07-04 4:56 ` gerg
0 siblings, 0 replies; 14+ messages in thread
From: gerg @ 2012-07-04 4:56 UTC (permalink / raw)
To: netdev, linux-m68k
The following 2 patches add platform support for using the NS8390 based
ethernet ports used on some ColdFire CPU boards. Patches to use these
have existed out-of-tree for years. Some of the base IO definitions
(those in arch/m68k/include/asm/mcfne.h) have been in mainline, but unused
for most of that time.
The first patch just neatens up mcfne.h (moving it to mcf8390.h). The
second patch is the platform driver. The first patch would normaly just
go through the m68knommu git tree, but I figured keeping these together made
more sense.
---
arch/m68k/include/asm/mcf8390.h | 371 ++++++++++++++++++---------
arch/m68k/include/asm/mcfne.h | 242 ------------------
drivers/net/ethernet/8390/Kconfig | 14 +
drivers/net/ethernet/8390/Makefile | 1
drivers/net/ethernet/8390/mcf8390.c | 478 ++++++++++++++++++++++++++++++++++++
5 files changed, 744 insertions(+), 362 deletions(-)
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 1/2] m68knommu: move the badly named mcfne.h to a better mcf8390.h
2012-07-04 4:56 ` gerg
@ 2012-07-04 4:56 ` gerg
-1 siblings, 0 replies; 14+ messages in thread
From: gerg @ 2012-07-04 4:56 UTC (permalink / raw)
To: netdev, linux-m68k; +Cc: Greg Ungerer
From: Greg Ungerer <gerg@uclinux.org>
The mcfne.h include contains definitions to support NS8390 eth based hardware
on ColdFire based CPU boards. So change its name to reflect that better.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
---
arch/m68k/include/asm/mcf8390.h | 242 +++++++++++++++++++++++++++++++++++++++
arch/m68k/include/asm/mcfne.h | 242 ---------------------------------------
2 files changed, 242 insertions(+), 242 deletions(-)
create mode 100644 arch/m68k/include/asm/mcf8390.h
delete mode 100644 arch/m68k/include/asm/mcfne.h
diff --git a/arch/m68k/include/asm/mcf8390.h b/arch/m68k/include/asm/mcf8390.h
new file mode 100644
index 0000000..bf3d97b
--- /dev/null
+++ b/arch/m68k/include/asm/mcf8390.h
@@ -0,0 +1,242 @@
+/****************************************************************************/
+
+/*
+ * mcf8390.h -- NS8390 support for ColdFire eval boards.
+ *
+ * (C) Copyright 1999-2000, Greg Ungerer (gerg@snapgear.com)
+ * (C) Copyright 2000, Lineo (www.lineo.com)
+ * (C) Copyright 2001, SnapGear (www.snapgear.com)
+ *
+ * 19990409 David W. Miller Converted from m5206ne.h for 5307 eval board
+ *
+ * Hacked support for m5206e Cadre III evaluation board
+ * Fred Stevens (fred.stevens@pemstar.com) 13 April 1999
+ */
+
+/****************************************************************************/
+#ifndef mcf8390_h
+#define mcf8390_h
+/****************************************************************************/
+
+
+/*
+ * Support for NE2000 clones devices in ColdFire based boards.
+ * Not all boards address these parts the same way, some use a
+ * direct addressing method, others use a side-band address space
+ * to access odd address registers, some require byte swapping
+ * others do not.
+ */
+#define BSWAP(w) (((w) << 8) | ((w) >> 8))
+#define RSWAP(w) (w)
+
+
+/*
+ * Define the basic hardware resources of NE2000 boards.
+ */
+
+#if defined(CONFIG_ARN5206)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0xf0
+#define NE2000_IRQ_PRIORITY 2
+#define NE2000_IRQ_LEVEL 4
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5206eC3)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1c
+#define NE2000_IRQ_PRIORITY 2
+#define NE2000_IRQ_LEVEL 4
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5206e) && defined(CONFIG_NETtel)
+#define NE2000_ADDR 0x30000300
+#define NE2000_IRQ_VECTOR 25
+#define NE2000_IRQ_PRIORITY 1
+#define NE2000_IRQ_LEVEL 3
+#define NE2000_BYTE volatile unsigned char
+#endif
+
+#if defined(CONFIG_M5307C3)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1b
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5272) && defined(CONFIG_NETtel)
+#define NE2000_ADDR 0x30600300
+#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_IRQ_VECTOR 67
+#undef BSWAP
+#define BSWAP(w) (w)
+#define NE2000_BYTE volatile unsigned short
+#undef RSWAP
+#define RSWAP(w) (((w) << 8) | ((w) >> 8))
+#endif
+
+#if defined(CONFIG_M5307) && defined(CONFIG_NETtel)
+#define NE2000_ADDR0 0x30600300
+#define NE2000_ADDR1 0x30800300
+#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_IRQ_VECTOR0 27
+#define NE2000_IRQ_VECTOR1 29
+#undef BSWAP
+#define BSWAP(w) (w)
+#define NE2000_BYTE volatile unsigned short
+#undef RSWAP
+#define RSWAP(w) (((w) << 8) | ((w) >> 8))
+#endif
+
+#if defined(CONFIG_M5307) && defined(CONFIG_SECUREEDGEMP3)
+#define NE2000_ADDR 0x30600300
+#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_IRQ_VECTOR 27
+#undef BSWAP
+#define BSWAP(w) (w)
+#define NE2000_BYTE volatile unsigned short
+#undef RSWAP
+#define RSWAP(w) (((w) << 8) | ((w) >> 8))
+#endif
+
+#if defined(CONFIG_ARN5307)
+#define NE2000_ADDR 0xfe600300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1b
+#define NE2000_IRQ_PRIORITY 2
+#define NE2000_IRQ_LEVEL 3
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5407C3)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1b
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+/****************************************************************************/
+
+/*
+ * Side-band address space for odd address requires re-mapping
+ * many of the standard ISA access functions.
+ */
+#ifdef NE2000_ODDOFFSET
+
+#undef outb
+#undef outb_p
+#undef inb
+#undef inb_p
+#undef outsb
+#undef outsw
+#undef insb
+#undef insw
+
+#define outb ne2000_outb
+#define inb ne2000_inb
+#define outb_p ne2000_outb
+#define inb_p ne2000_inb
+#define outsb ne2000_outsb
+#define outsw ne2000_outsw
+#define insb ne2000_insb
+#define insw ne2000_insw
+
+
+#ifndef COLDFIRE_NE2000_FUNCS
+
+void ne2000_outb(unsigned int val, unsigned int addr);
+int ne2000_inb(unsigned int addr);
+void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len);
+void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len);
+void ne2000_outsb(unsigned int addr, void *vbuf, unsigned long len);
+void ne2000_outsw(unsigned int addr, void *vbuf, unsigned long len);
+
+#else
+
+/*
+ * This macro converts a conventional register address into the
+ * real memory pointer of the mapped NE2000 device.
+ * On most NE2000 implementations on ColdFire boards the chip is
+ * mapped in kinda funny, due to its ISA heritage.
+ */
+#define NE2000_PTR(addr) ((addr&0x1)?(NE2000_ODDOFFSET+addr-1):(addr))
+#define NE2000_DATA_PTR(addr) (addr)
+
+
+void ne2000_outb(unsigned int val, unsigned int addr)
+{
+ NE2000_BYTE *rp;
+
+ rp = (NE2000_BYTE *) NE2000_PTR(addr);
+ *rp = RSWAP(val);
+}
+
+int ne2000_inb(unsigned int addr)
+{
+ NE2000_BYTE *rp, val;
+
+ rp = (NE2000_BYTE *) NE2000_PTR(addr);
+ val = *rp;
+ return((int) ((NE2000_BYTE) RSWAP(val)));
+}
+
+void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len)
+{
+ NE2000_BYTE *rp, val;
+ unsigned char *buf;
+
+ buf = (unsigned char *) vbuf;
+ rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *rp;
+ *buf++ = RSWAP(val);
+ }
+}
+
+void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len)
+{
+ volatile unsigned short *rp;
+ unsigned short w, *buf;
+
+ buf = (unsigned short *) vbuf;
+ rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *rp;
+ *buf++ = BSWAP(w);
+ }
+}
+
+void ne2000_outsb(unsigned int addr, const void *vbuf, unsigned long len)
+{
+ NE2000_BYTE *rp, val;
+ unsigned char *buf;
+
+ buf = (unsigned char *) vbuf;
+ rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *buf++;
+ *rp = RSWAP(val);
+ }
+}
+
+void ne2000_outsw(unsigned int addr, const void *vbuf, unsigned long len)
+{
+ volatile unsigned short *rp;
+ unsigned short w, *buf;
+
+ buf = (unsigned short *) vbuf;
+ rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *buf++;
+ *rp = BSWAP(w);
+ }
+}
+
+#endif /* COLDFIRE_NE2000_FUNCS */
+#endif /* NE2000_OFFOFFSET */
+
+/****************************************************************************/
+#endif /* mcf8390_h */
diff --git a/arch/m68k/include/asm/mcfne.h b/arch/m68k/include/asm/mcfne.h
deleted file mode 100644
index bf638be..0000000
--- a/arch/m68k/include/asm/mcfne.h
+++ /dev/null
@@ -1,242 +0,0 @@
-/****************************************************************************/
-
-/*
- * mcfne.h -- NE2000 in ColdFire eval boards.
- *
- * (C) Copyright 1999-2000, Greg Ungerer (gerg@snapgear.com)
- * (C) Copyright 2000, Lineo (www.lineo.com)
- * (C) Copyright 2001, SnapGear (www.snapgear.com)
- *
- * 19990409 David W. Miller Converted from m5206ne.h for 5307 eval board
- *
- * Hacked support for m5206e Cadre III evaluation board
- * Fred Stevens (fred.stevens@pemstar.com) 13 April 1999
- */
-
-/****************************************************************************/
-#ifndef mcfne_h
-#define mcfne_h
-/****************************************************************************/
-
-
-/*
- * Support for NE2000 clones devices in ColdFire based boards.
- * Not all boards address these parts the same way, some use a
- * direct addressing method, others use a side-band address space
- * to access odd address registers, some require byte swapping
- * others do not.
- */
-#define BSWAP(w) (((w) << 8) | ((w) >> 8))
-#define RSWAP(w) (w)
-
-
-/*
- * Define the basic hardware resources of NE2000 boards.
- */
-
-#if defined(CONFIG_ARN5206)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0xf0
-#define NE2000_IRQ_PRIORITY 2
-#define NE2000_IRQ_LEVEL 4
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5206eC3)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1c
-#define NE2000_IRQ_PRIORITY 2
-#define NE2000_IRQ_LEVEL 4
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5206e) && defined(CONFIG_NETtel)
-#define NE2000_ADDR 0x30000300
-#define NE2000_IRQ_VECTOR 25
-#define NE2000_IRQ_PRIORITY 1
-#define NE2000_IRQ_LEVEL 3
-#define NE2000_BYTE volatile unsigned char
-#endif
-
-#if defined(CONFIG_M5307C3)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1b
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5272) && defined(CONFIG_NETtel)
-#define NE2000_ADDR 0x30600300
-#define NE2000_ODDOFFSET 0x00008000
-#define NE2000_IRQ_VECTOR 67
-#undef BSWAP
-#define BSWAP(w) (w)
-#define NE2000_BYTE volatile unsigned short
-#undef RSWAP
-#define RSWAP(w) (((w) << 8) | ((w) >> 8))
-#endif
-
-#if defined(CONFIG_M5307) && defined(CONFIG_NETtel)
-#define NE2000_ADDR0 0x30600300
-#define NE2000_ADDR1 0x30800300
-#define NE2000_ODDOFFSET 0x00008000
-#define NE2000_IRQ_VECTOR0 27
-#define NE2000_IRQ_VECTOR1 29
-#undef BSWAP
-#define BSWAP(w) (w)
-#define NE2000_BYTE volatile unsigned short
-#undef RSWAP
-#define RSWAP(w) (((w) << 8) | ((w) >> 8))
-#endif
-
-#if defined(CONFIG_M5307) && defined(CONFIG_SECUREEDGEMP3)
-#define NE2000_ADDR 0x30600300
-#define NE2000_ODDOFFSET 0x00008000
-#define NE2000_IRQ_VECTOR 27
-#undef BSWAP
-#define BSWAP(w) (w)
-#define NE2000_BYTE volatile unsigned short
-#undef RSWAP
-#define RSWAP(w) (((w) << 8) | ((w) >> 8))
-#endif
-
-#if defined(CONFIG_ARN5307)
-#define NE2000_ADDR 0xfe600300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1b
-#define NE2000_IRQ_PRIORITY 2
-#define NE2000_IRQ_LEVEL 3
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5407C3)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1b
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-/****************************************************************************/
-
-/*
- * Side-band address space for odd address requires re-mapping
- * many of the standard ISA access functions.
- */
-#ifdef NE2000_ODDOFFSET
-
-#undef outb
-#undef outb_p
-#undef inb
-#undef inb_p
-#undef outsb
-#undef outsw
-#undef insb
-#undef insw
-
-#define outb ne2000_outb
-#define inb ne2000_inb
-#define outb_p ne2000_outb
-#define inb_p ne2000_inb
-#define outsb ne2000_outsb
-#define outsw ne2000_outsw
-#define insb ne2000_insb
-#define insw ne2000_insw
-
-
-#ifndef COLDFIRE_NE2000_FUNCS
-
-void ne2000_outb(unsigned int val, unsigned int addr);
-int ne2000_inb(unsigned int addr);
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len);
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsb(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsw(unsigned int addr, void *vbuf, unsigned long len);
-
-#else
-
-/*
- * This macro converts a conventional register address into the
- * real memory pointer of the mapped NE2000 device.
- * On most NE2000 implementations on ColdFire boards the chip is
- * mapped in kinda funny, due to its ISA heritage.
- */
-#define NE2000_PTR(addr) ((addr&0x1)?(NE2000_ODDOFFSET+addr-1):(addr))
-#define NE2000_DATA_PTR(addr) (addr)
-
-
-void ne2000_outb(unsigned int val, unsigned int addr)
-{
- NE2000_BYTE *rp;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- *rp = RSWAP(val);
-}
-
-int ne2000_inb(unsigned int addr)
-{
- NE2000_BYTE *rp, val;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- val = *rp;
- return((int) ((NE2000_BYTE) RSWAP(val)));
-}
-
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *rp;
- *buf++ = RSWAP(val);
- }
-}
-
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *rp;
- *buf++ = BSWAP(w);
- }
-}
-
-void ne2000_outsb(unsigned int addr, const void *vbuf, unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *buf++;
- *rp = RSWAP(val);
- }
-}
-
-void ne2000_outsw(unsigned int addr, const void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *buf++;
- *rp = BSWAP(w);
- }
-}
-
-#endif /* COLDFIRE_NE2000_FUNCS */
-#endif /* NE2000_OFFOFFSET */
-
-/****************************************************************************/
-#endif /* mcfne_h */
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 1/2] m68knommu: move the badly named mcfne.h to a better mcf8390.h
@ 2012-07-04 4:56 ` gerg
0 siblings, 0 replies; 14+ messages in thread
From: gerg @ 2012-07-04 4:56 UTC (permalink / raw)
To: netdev, linux-m68k; +Cc: Greg Ungerer
From: Greg Ungerer <gerg@uclinux.org>
The mcfne.h include contains definitions to support NS8390 eth based hardware
on ColdFire based CPU boards. So change its name to reflect that better.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
---
arch/m68k/include/asm/mcf8390.h | 242 +++++++++++++++++++++++++++++++++++++++
arch/m68k/include/asm/mcfne.h | 242 ---------------------------------------
2 files changed, 242 insertions(+), 242 deletions(-)
create mode 100644 arch/m68k/include/asm/mcf8390.h
delete mode 100644 arch/m68k/include/asm/mcfne.h
diff --git a/arch/m68k/include/asm/mcf8390.h b/arch/m68k/include/asm/mcf8390.h
new file mode 100644
index 0000000..bf3d97b
--- /dev/null
+++ b/arch/m68k/include/asm/mcf8390.h
@@ -0,0 +1,242 @@
+/****************************************************************************/
+
+/*
+ * mcf8390.h -- NS8390 support for ColdFire eval boards.
+ *
+ * (C) Copyright 1999-2000, Greg Ungerer (gerg@snapgear.com)
+ * (C) Copyright 2000, Lineo (www.lineo.com)
+ * (C) Copyright 2001, SnapGear (www.snapgear.com)
+ *
+ * 19990409 David W. Miller Converted from m5206ne.h for 5307 eval board
+ *
+ * Hacked support for m5206e Cadre III evaluation board
+ * Fred Stevens (fred.stevens@pemstar.com) 13 April 1999
+ */
+
+/****************************************************************************/
+#ifndef mcf8390_h
+#define mcf8390_h
+/****************************************************************************/
+
+
+/*
+ * Support for NE2000 clones devices in ColdFire based boards.
+ * Not all boards address these parts the same way, some use a
+ * direct addressing method, others use a side-band address space
+ * to access odd address registers, some require byte swapping
+ * others do not.
+ */
+#define BSWAP(w) (((w) << 8) | ((w) >> 8))
+#define RSWAP(w) (w)
+
+
+/*
+ * Define the basic hardware resources of NE2000 boards.
+ */
+
+#if defined(CONFIG_ARN5206)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0xf0
+#define NE2000_IRQ_PRIORITY 2
+#define NE2000_IRQ_LEVEL 4
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5206eC3)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1c
+#define NE2000_IRQ_PRIORITY 2
+#define NE2000_IRQ_LEVEL 4
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5206e) && defined(CONFIG_NETtel)
+#define NE2000_ADDR 0x30000300
+#define NE2000_IRQ_VECTOR 25
+#define NE2000_IRQ_PRIORITY 1
+#define NE2000_IRQ_LEVEL 3
+#define NE2000_BYTE volatile unsigned char
+#endif
+
+#if defined(CONFIG_M5307C3)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1b
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5272) && defined(CONFIG_NETtel)
+#define NE2000_ADDR 0x30600300
+#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_IRQ_VECTOR 67
+#undef BSWAP
+#define BSWAP(w) (w)
+#define NE2000_BYTE volatile unsigned short
+#undef RSWAP
+#define RSWAP(w) (((w) << 8) | ((w) >> 8))
+#endif
+
+#if defined(CONFIG_M5307) && defined(CONFIG_NETtel)
+#define NE2000_ADDR0 0x30600300
+#define NE2000_ADDR1 0x30800300
+#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_IRQ_VECTOR0 27
+#define NE2000_IRQ_VECTOR1 29
+#undef BSWAP
+#define BSWAP(w) (w)
+#define NE2000_BYTE volatile unsigned short
+#undef RSWAP
+#define RSWAP(w) (((w) << 8) | ((w) >> 8))
+#endif
+
+#if defined(CONFIG_M5307) && defined(CONFIG_SECUREEDGEMP3)
+#define NE2000_ADDR 0x30600300
+#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_IRQ_VECTOR 27
+#undef BSWAP
+#define BSWAP(w) (w)
+#define NE2000_BYTE volatile unsigned short
+#undef RSWAP
+#define RSWAP(w) (((w) << 8) | ((w) >> 8))
+#endif
+
+#if defined(CONFIG_ARN5307)
+#define NE2000_ADDR 0xfe600300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1b
+#define NE2000_IRQ_PRIORITY 2
+#define NE2000_IRQ_LEVEL 3
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+#if defined(CONFIG_M5407C3)
+#define NE2000_ADDR 0x40000300
+#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_IRQ_VECTOR 0x1b
+#define NE2000_BYTE volatile unsigned short
+#endif
+
+/****************************************************************************/
+
+/*
+ * Side-band address space for odd address requires re-mapping
+ * many of the standard ISA access functions.
+ */
+#ifdef NE2000_ODDOFFSET
+
+#undef outb
+#undef outb_p
+#undef inb
+#undef inb_p
+#undef outsb
+#undef outsw
+#undef insb
+#undef insw
+
+#define outb ne2000_outb
+#define inb ne2000_inb
+#define outb_p ne2000_outb
+#define inb_p ne2000_inb
+#define outsb ne2000_outsb
+#define outsw ne2000_outsw
+#define insb ne2000_insb
+#define insw ne2000_insw
+
+
+#ifndef COLDFIRE_NE2000_FUNCS
+
+void ne2000_outb(unsigned int val, unsigned int addr);
+int ne2000_inb(unsigned int addr);
+void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len);
+void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len);
+void ne2000_outsb(unsigned int addr, void *vbuf, unsigned long len);
+void ne2000_outsw(unsigned int addr, void *vbuf, unsigned long len);
+
+#else
+
+/*
+ * This macro converts a conventional register address into the
+ * real memory pointer of the mapped NE2000 device.
+ * On most NE2000 implementations on ColdFire boards the chip is
+ * mapped in kinda funny, due to its ISA heritage.
+ */
+#define NE2000_PTR(addr) ((addr&0x1)?(NE2000_ODDOFFSET+addr-1):(addr))
+#define NE2000_DATA_PTR(addr) (addr)
+
+
+void ne2000_outb(unsigned int val, unsigned int addr)
+{
+ NE2000_BYTE *rp;
+
+ rp = (NE2000_BYTE *) NE2000_PTR(addr);
+ *rp = RSWAP(val);
+}
+
+int ne2000_inb(unsigned int addr)
+{
+ NE2000_BYTE *rp, val;
+
+ rp = (NE2000_BYTE *) NE2000_PTR(addr);
+ val = *rp;
+ return((int) ((NE2000_BYTE) RSWAP(val)));
+}
+
+void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len)
+{
+ NE2000_BYTE *rp, val;
+ unsigned char *buf;
+
+ buf = (unsigned char *) vbuf;
+ rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *rp;
+ *buf++ = RSWAP(val);
+ }
+}
+
+void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len)
+{
+ volatile unsigned short *rp;
+ unsigned short w, *buf;
+
+ buf = (unsigned short *) vbuf;
+ rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *rp;
+ *buf++ = BSWAP(w);
+ }
+}
+
+void ne2000_outsb(unsigned int addr, const void *vbuf, unsigned long len)
+{
+ NE2000_BYTE *rp, val;
+ unsigned char *buf;
+
+ buf = (unsigned char *) vbuf;
+ rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *buf++;
+ *rp = RSWAP(val);
+ }
+}
+
+void ne2000_outsw(unsigned int addr, const void *vbuf, unsigned long len)
+{
+ volatile unsigned short *rp;
+ unsigned short w, *buf;
+
+ buf = (unsigned short *) vbuf;
+ rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *buf++;
+ *rp = BSWAP(w);
+ }
+}
+
+#endif /* COLDFIRE_NE2000_FUNCS */
+#endif /* NE2000_OFFOFFSET */
+
+/****************************************************************************/
+#endif /* mcf8390_h */
diff --git a/arch/m68k/include/asm/mcfne.h b/arch/m68k/include/asm/mcfne.h
deleted file mode 100644
index bf638be..0000000
--- a/arch/m68k/include/asm/mcfne.h
+++ /dev/null
@@ -1,242 +0,0 @@
-/****************************************************************************/
-
-/*
- * mcfne.h -- NE2000 in ColdFire eval boards.
- *
- * (C) Copyright 1999-2000, Greg Ungerer (gerg@snapgear.com)
- * (C) Copyright 2000, Lineo (www.lineo.com)
- * (C) Copyright 2001, SnapGear (www.snapgear.com)
- *
- * 19990409 David W. Miller Converted from m5206ne.h for 5307 eval board
- *
- * Hacked support for m5206e Cadre III evaluation board
- * Fred Stevens (fred.stevens@pemstar.com) 13 April 1999
- */
-
-/****************************************************************************/
-#ifndef mcfne_h
-#define mcfne_h
-/****************************************************************************/
-
-
-/*
- * Support for NE2000 clones devices in ColdFire based boards.
- * Not all boards address these parts the same way, some use a
- * direct addressing method, others use a side-band address space
- * to access odd address registers, some require byte swapping
- * others do not.
- */
-#define BSWAP(w) (((w) << 8) | ((w) >> 8))
-#define RSWAP(w) (w)
-
-
-/*
- * Define the basic hardware resources of NE2000 boards.
- */
-
-#if defined(CONFIG_ARN5206)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0xf0
-#define NE2000_IRQ_PRIORITY 2
-#define NE2000_IRQ_LEVEL 4
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5206eC3)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1c
-#define NE2000_IRQ_PRIORITY 2
-#define NE2000_IRQ_LEVEL 4
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5206e) && defined(CONFIG_NETtel)
-#define NE2000_ADDR 0x30000300
-#define NE2000_IRQ_VECTOR 25
-#define NE2000_IRQ_PRIORITY 1
-#define NE2000_IRQ_LEVEL 3
-#define NE2000_BYTE volatile unsigned char
-#endif
-
-#if defined(CONFIG_M5307C3)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1b
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5272) && defined(CONFIG_NETtel)
-#define NE2000_ADDR 0x30600300
-#define NE2000_ODDOFFSET 0x00008000
-#define NE2000_IRQ_VECTOR 67
-#undef BSWAP
-#define BSWAP(w) (w)
-#define NE2000_BYTE volatile unsigned short
-#undef RSWAP
-#define RSWAP(w) (((w) << 8) | ((w) >> 8))
-#endif
-
-#if defined(CONFIG_M5307) && defined(CONFIG_NETtel)
-#define NE2000_ADDR0 0x30600300
-#define NE2000_ADDR1 0x30800300
-#define NE2000_ODDOFFSET 0x00008000
-#define NE2000_IRQ_VECTOR0 27
-#define NE2000_IRQ_VECTOR1 29
-#undef BSWAP
-#define BSWAP(w) (w)
-#define NE2000_BYTE volatile unsigned short
-#undef RSWAP
-#define RSWAP(w) (((w) << 8) | ((w) >> 8))
-#endif
-
-#if defined(CONFIG_M5307) && defined(CONFIG_SECUREEDGEMP3)
-#define NE2000_ADDR 0x30600300
-#define NE2000_ODDOFFSET 0x00008000
-#define NE2000_IRQ_VECTOR 27
-#undef BSWAP
-#define BSWAP(w) (w)
-#define NE2000_BYTE volatile unsigned short
-#undef RSWAP
-#define RSWAP(w) (((w) << 8) | ((w) >> 8))
-#endif
-
-#if defined(CONFIG_ARN5307)
-#define NE2000_ADDR 0xfe600300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1b
-#define NE2000_IRQ_PRIORITY 2
-#define NE2000_IRQ_LEVEL 3
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-#if defined(CONFIG_M5407C3)
-#define NE2000_ADDR 0x40000300
-#define NE2000_ODDOFFSET 0x00010000
-#define NE2000_IRQ_VECTOR 0x1b
-#define NE2000_BYTE volatile unsigned short
-#endif
-
-/****************************************************************************/
-
-/*
- * Side-band address space for odd address requires re-mapping
- * many of the standard ISA access functions.
- */
-#ifdef NE2000_ODDOFFSET
-
-#undef outb
-#undef outb_p
-#undef inb
-#undef inb_p
-#undef outsb
-#undef outsw
-#undef insb
-#undef insw
-
-#define outb ne2000_outb
-#define inb ne2000_inb
-#define outb_p ne2000_outb
-#define inb_p ne2000_inb
-#define outsb ne2000_outsb
-#define outsw ne2000_outsw
-#define insb ne2000_insb
-#define insw ne2000_insw
-
-
-#ifndef COLDFIRE_NE2000_FUNCS
-
-void ne2000_outb(unsigned int val, unsigned int addr);
-int ne2000_inb(unsigned int addr);
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len);
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsb(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsw(unsigned int addr, void *vbuf, unsigned long len);
-
-#else
-
-/*
- * This macro converts a conventional register address into the
- * real memory pointer of the mapped NE2000 device.
- * On most NE2000 implementations on ColdFire boards the chip is
- * mapped in kinda funny, due to its ISA heritage.
- */
-#define NE2000_PTR(addr) ((addr&0x1)?(NE2000_ODDOFFSET+addr-1):(addr))
-#define NE2000_DATA_PTR(addr) (addr)
-
-
-void ne2000_outb(unsigned int val, unsigned int addr)
-{
- NE2000_BYTE *rp;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- *rp = RSWAP(val);
-}
-
-int ne2000_inb(unsigned int addr)
-{
- NE2000_BYTE *rp, val;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- val = *rp;
- return((int) ((NE2000_BYTE) RSWAP(val)));
-}
-
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *rp;
- *buf++ = RSWAP(val);
- }
-}
-
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *rp;
- *buf++ = BSWAP(w);
- }
-}
-
-void ne2000_outsb(unsigned int addr, const void *vbuf, unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *buf++;
- *rp = RSWAP(val);
- }
-}
-
-void ne2000_outsw(unsigned int addr, const void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *buf++;
- *rp = BSWAP(w);
- }
-}
-
-#endif /* COLDFIRE_NE2000_FUNCS */
-#endif /* NE2000_OFFOFFSET */
-
-/****************************************************************************/
-#endif /* mcfne_h */
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 4:56 ` gerg
@ 2012-07-04 4:56 ` gerg
-1 siblings, 0 replies; 14+ messages in thread
From: gerg @ 2012-07-04 4:56 UTC (permalink / raw)
To: netdev, linux-m68k; +Cc: Greg Ungerer
From: Greg Ungerer <gerg@uclinux.org>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
---
arch/m68k/include/asm/mcf8390.h | 129 +---------
drivers/net/ethernet/8390/Kconfig | 14 +
drivers/net/ethernet/8390/Makefile | 1 +
drivers/net/ethernet/8390/mcf8390.c | 478 +++++++++++++++++++++++++++++++++++
4 files changed, 502 insertions(+), 120 deletions(-)
create mode 100644 drivers/net/ethernet/8390/mcf8390.c
diff --git a/arch/m68k/include/asm/mcf8390.h b/arch/m68k/include/asm/mcf8390.h
index bf3d97b..a72a208 100644
--- a/arch/m68k/include/asm/mcf8390.h
+++ b/arch/m68k/include/asm/mcf8390.h
@@ -37,6 +37,7 @@
#if defined(CONFIG_ARN5206)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0xf0
#define NE2000_IRQ_PRIORITY 2
#define NE2000_IRQ_LEVEL 4
@@ -46,6 +47,7 @@
#if defined(CONFIG_M5206eC3)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1c
#define NE2000_IRQ_PRIORITY 2
#define NE2000_IRQ_LEVEL 4
@@ -54,6 +56,7 @@
#if defined(CONFIG_M5206e) && defined(CONFIG_NETtel)
#define NE2000_ADDR 0x30000300
+#define NE2000_ADDRSIZE 0x00001000
#define NE2000_IRQ_VECTOR 25
#define NE2000_IRQ_PRIORITY 1
#define NE2000_IRQ_LEVEL 3
@@ -63,6 +66,7 @@
#if defined(CONFIG_M5307C3)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1b
#define NE2000_BYTE volatile unsigned short
#endif
@@ -70,6 +74,7 @@
#if defined(CONFIG_M5272) && defined(CONFIG_NETtel)
#define NE2000_ADDR 0x30600300
#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_ADDRSIZE 0x00010000
#define NE2000_IRQ_VECTOR 67
#undef BSWAP
#define BSWAP(w) (w)
@@ -82,6 +87,7 @@
#define NE2000_ADDR0 0x30600300
#define NE2000_ADDR1 0x30800300
#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_ADDRSIZE 0x00010000
#define NE2000_IRQ_VECTOR0 27
#define NE2000_IRQ_VECTOR1 29
#undef BSWAP
@@ -94,6 +100,7 @@
#if defined(CONFIG_M5307) && defined(CONFIG_SECUREEDGEMP3)
#define NE2000_ADDR 0x30600300
#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_ADDRSIZE 0x00010000
#define NE2000_IRQ_VECTOR 27
#undef BSWAP
#define BSWAP(w) (w)
@@ -105,6 +112,7 @@
#if defined(CONFIG_ARN5307)
#define NE2000_ADDR 0xfe600300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1b
#define NE2000_IRQ_PRIORITY 2
#define NE2000_IRQ_LEVEL 3
@@ -114,129 +122,10 @@
#if defined(CONFIG_M5407C3)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1b
#define NE2000_BYTE volatile unsigned short
#endif
/****************************************************************************/
-
-/*
- * Side-band address space for odd address requires re-mapping
- * many of the standard ISA access functions.
- */
-#ifdef NE2000_ODDOFFSET
-
-#undef outb
-#undef outb_p
-#undef inb
-#undef inb_p
-#undef outsb
-#undef outsw
-#undef insb
-#undef insw
-
-#define outb ne2000_outb
-#define inb ne2000_inb
-#define outb_p ne2000_outb
-#define inb_p ne2000_inb
-#define outsb ne2000_outsb
-#define outsw ne2000_outsw
-#define insb ne2000_insb
-#define insw ne2000_insw
-
-
-#ifndef COLDFIRE_NE2000_FUNCS
-
-void ne2000_outb(unsigned int val, unsigned int addr);
-int ne2000_inb(unsigned int addr);
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len);
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsb(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsw(unsigned int addr, void *vbuf, unsigned long len);
-
-#else
-
-/*
- * This macro converts a conventional register address into the
- * real memory pointer of the mapped NE2000 device.
- * On most NE2000 implementations on ColdFire boards the chip is
- * mapped in kinda funny, due to its ISA heritage.
- */
-#define NE2000_PTR(addr) ((addr&0x1)?(NE2000_ODDOFFSET+addr-1):(addr))
-#define NE2000_DATA_PTR(addr) (addr)
-
-
-void ne2000_outb(unsigned int val, unsigned int addr)
-{
- NE2000_BYTE *rp;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- *rp = RSWAP(val);
-}
-
-int ne2000_inb(unsigned int addr)
-{
- NE2000_BYTE *rp, val;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- val = *rp;
- return((int) ((NE2000_BYTE) RSWAP(val)));
-}
-
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *rp;
- *buf++ = RSWAP(val);
- }
-}
-
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *rp;
- *buf++ = BSWAP(w);
- }
-}
-
-void ne2000_outsb(unsigned int addr, const void *vbuf, unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *buf++;
- *rp = RSWAP(val);
- }
-}
-
-void ne2000_outsw(unsigned int addr, const void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *buf++;
- *rp = BSWAP(w);
- }
-}
-
-#endif /* COLDFIRE_NE2000_FUNCS */
-#endif /* NE2000_OFFOFFSET */
-
-/****************************************************************************/
#endif /* mcf8390_h */
diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index 2e53867..e1219e0 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -162,6 +162,20 @@ config MAC8390
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
+config MCF8390
+ tristate "ColdFire NS8390 based Ethernet support"
+ depends on COLDFIRE
+ select CRC32
+ ---help---
+ This driver is for Ethernet devices using an NS8390-compatible
+ chipset on many common ColdFire CPU based boards. Many of the older
+ Freescale dev boards use this, and some other common boards like
+ some SnapGear routers do as well.
+
+ If you have one of these boards and want to use the network interface
+ on them then choose Y. To compile this driver as a module, choose M
+ here, the module will be called mcf8390.
+
config NE2000
tristate "NE2000/NE1000 support"
depends on (ISA || (Q40 && m) || M32R || MACH_TX49XX)
diff --git a/drivers/net/ethernet/8390/Makefile b/drivers/net/ethernet/8390/Makefile
index d13790b..f43038b 100644
--- a/drivers/net/ethernet/8390/Makefile
+++ b/drivers/net/ethernet/8390/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390p.o
obj-$(CONFIG_HPLAN) += hp.o 8390p.o
obj-$(CONFIG_HYDRA) += hydra.o 8390.o
obj-$(CONFIG_LNE390) += lne390.o 8390.o
+obj-$(CONFIG_MCF8390) += mcf8390.o 8390.o
obj-$(CONFIG_NE2000) += ne.o 8390p.o
obj-$(CONFIG_NE2_MCA) += ne2.o 8390p.o
obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c
new file mode 100644
index 0000000..12b3d40
--- /dev/null
+++ b/drivers/net/ethernet/8390/mcf8390.c
@@ -0,0 +1,478 @@
+/*
+ * Support for ColdFire CPU based boards using a NS8390 Ethernet device.
+ *
+ * Derived from the many other 8390 drivers.
+ *
+ * (C) Copyright 2012, Greg Ungerer <gerg@uclinux.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of the Linux
+ * distribution for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/jiffies.h>
+#include <linux/io.h>
+#include <asm/mcf8390.h>
+
+static const char version[] =
+ "mcf8390.c: (15-06-2012) Greg Ungerer <gerg@uclinux.org>";
+
+#define NE_CMD 0x00
+#define NE_DATAPORT 0x10 /* NatSemi-defined port window offset */
+#define NE_RESET 0x1f /* Issue a read to reset ,a write to clear */
+#define NE_EN0_ISR 0x07
+#define NE_EN0_DCFG 0x0e
+#define NE_EN0_RSARLO 0x08
+#define NE_EN0_RSARHI 0x09
+#define NE_EN0_RCNTLO 0x0a
+#define NE_EN0_RXCR 0x0c
+#define NE_EN0_TXCR 0x0d
+#define NE_EN0_RCNTHI 0x0b
+#define NE_EN0_IMR 0x0f
+
+#define NESM_START_PG 0x40 /* First page of TX buffer */
+#define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */
+
+#ifdef NE2000_ODDOFFSET
+/*
+ * A lot of the ColdFire boards use a separate address region for odd offset
+ * register addresses. The following macros and functions convert and map
+ * as required. Note that the data port accesses are treated a little
+ * differently, and always accessed via the insX/outsX functions.
+ */
+#define NE_PTR(a) (((a) & 0x1) ? (NE2000_ODDOFFSET + (a) - 1) : (a))
+#define NE_DATA_PTR(a) (a)
+
+void ei_outb(u32 val, u32 addr)
+{
+ NE2000_BYTE *rp;
+
+ rp = (NE2000_BYTE *) NE_PTR(addr);
+ *rp = RSWAP(val);
+}
+
+#define ei_inb ei_inb
+u8 ei_inb(u32 addr)
+{
+ NE2000_BYTE *rp, val;
+
+ rp = (NE2000_BYTE *) NE_PTR(addr);
+ val = *rp;
+ return (u8) (RSWAP(val) & 0xff);
+}
+
+void ei_insb(u32 addr, void *vbuf, int len)
+{
+ NE2000_BYTE *rp, val;
+ u8 *buf;
+
+ buf = (u8 *) vbuf;
+ rp = (NE2000_BYTE *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *rp;
+ *buf++ = RSWAP(val);
+ }
+}
+
+void ei_insw(u32 addr, void *vbuf, int len)
+{
+ volatile u16 *rp;
+ u16 w, *buf;
+
+ buf = (u16 *) vbuf;
+ rp = (volatile u16 *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *rp;
+ *buf++ = BSWAP(w);
+ }
+}
+
+void ei_outsb(u32 addr, const void *vbuf, int len)
+{
+ NE2000_BYTE *rp, val;
+ u8 *buf;
+
+ buf = (u8 *) vbuf;
+ rp = (NE2000_BYTE *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *buf++;
+ *rp = RSWAP(val);
+ }
+}
+
+void ei_outsw(u32 addr, const void *vbuf, int len)
+{
+ volatile u16 *rp;
+ u16 w, *buf;
+
+ buf = (u16 *) vbuf;
+ rp = (volatile u16 *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *buf++;
+ *rp = BSWAP(w);
+ }
+}
+
+#else /* !NE2000_ODDOFFSET */
+
+#define ei_inb inb
+#define ei_outb outb
+#define ei_insb insb
+#define ei_insw insw
+#define ei_outsb outsb
+#define ei_outsw outsw
+
+#endif /* !NE2000_ODDOFFSET */
+
+#define ei_inb_p ei_inb
+#define ei_outb_p ei_outb
+
+#include "lib8390.c"
+
+/*
+ * Hard reset the card. This used to pause for the same period that a
+ * 8390 reset command required, but that shouldn't be necessary.
+ */
+static void mcf8390_reset_8390(struct net_device *dev)
+{
+ unsigned long reset_start_time = jiffies;
+ u32 addr = dev->base_addr;
+
+ if (ei_debug > 1)
+ netdev_dbg(dev, "resetting the 8390 t=%ld...\n", jiffies);
+
+ ei_outb(ei_inb(addr + NE_RESET), addr + NE_RESET);
+
+ ei_status.txing = 0;
+ ei_status.dmaing = 0;
+
+ /* This check _should_not_ be necessary, omit eventually. */
+ while ((ei_inb(addr + NE_EN0_ISR) & ENISR_RESET) == 0) {
+ if (time_after(jiffies, reset_start_time + 2 * HZ / 100)) {
+ netdev_warn(dev, "%s: did not complete\n", __func__);
+ break;
+ }
+ }
+
+ ei_outb(ENISR_RESET, addr + NE_EN0_ISR);
+}
+
+/*
+ * Grab the 8390 specific header. Similar to the block_input routine, but
+ * we don't need to be concerned with ring wrap as the header will be at
+ * the start of a page, so we optimize accordingly.
+ */
+static void mcf8390_get_8390_hdr(struct net_device *dev,
+ struct e8390_pkt_hdr *hdr, int ring_page)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ u32 addr = dev->base_addr;
+
+ /*
+ * This *shouldn't* happen.
+ * If it does, it's the last thing you'll see
+ */
+ if (ei_status.dmaing) {
+ netdev_err(dev,
+ "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
+ __func__, ei_local->dmaing, ei_local->irqlock);
+ return;
+ }
+
+ ei_local->dmaing |= 0x01;
+ ei_outb(E8390_NODMA + E8390_PAGE0 + E8390_START, addr + NE_CMD);
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR);
+ ei_outb(sizeof(struct e8390_pkt_hdr), addr + NE_EN0_RCNTLO);
+ ei_outb(0, addr + NE_EN0_RCNTHI);
+ ei_outb(0, addr + NE_EN0_RSARLO); /* On page boundary */
+ ei_outb(ring_page, addr + NE_EN0_RSARHI);
+ ei_outb(E8390_RREAD + E8390_START, addr + NE_CMD);
+
+ ei_insw(addr + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr) >> 1);
+
+ outb(ENISR_RDC, addr + NE_EN0_ISR); /* Ack intr */
+ ei_local->dmaing &= ~0x01;
+
+ hdr->count = cpu_to_le16(hdr->count);
+}
+
+/*
+ * Block input and output, similar to the Crynwr packet driver.
+ * If you are porting to a new ethercard, look at the packet driver source
+ * for hints. The NEx000 doesn't share the on-board packet memory --
+ * you have to put the packet out through the "remote DMA" dataport
+ * using z_writeb.
+ */
+static void mcf8390_block_input(struct net_device *dev, int count,
+ struct sk_buff *skb, int ring_offset)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ u32 addr = dev->base_addr;
+ char *buf = skb->data;
+
+ /*
+ * This *shouldn't* happen.
+ * If it does, it's the last thing you'll see
+ */
+ if (ei_local->dmaing) {
+ netdev_err(dev,
+ "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
+ __func__, ei_local->dmaing, ei_local->irqlock);
+ return;
+ }
+
+ ei_local->dmaing |= 0x01;
+ ei_outb(E8390_NODMA + E8390_PAGE0 + E8390_START, addr + NE_CMD);
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR);
+ ei_outb(count & 0xff, addr + NE_EN0_RCNTLO);
+ ei_outb(count >> 8, addr + NE_EN0_RCNTHI);
+ ei_outb(ring_offset & 0xff, addr + NE_EN0_RSARLO);
+ ei_outb(ring_offset >> 8, addr + NE_EN0_RSARHI);
+ ei_outb(E8390_RREAD + E8390_START, addr + NE_CMD);
+
+ ei_insw(addr + NE_DATAPORT, buf, count >> 1);
+ if (count & 1)
+ buf[count - 1] = ei_inb(addr + NE_DATAPORT);
+
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR); /* Ack intr */
+ ei_local->dmaing &= ~0x01;
+}
+
+static void mcf8390_block_output(struct net_device *dev, int count,
+ const unsigned char *buf,
+ const int start_page)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ u32 addr = dev->base_addr;
+ unsigned long dma_start;
+
+ /* Make sure we transfer all bytes if 16bit IO writes */
+ if (count & 0x1)
+ count++;
+
+ /*
+ *This *shouldn't* happen.
+ * If it does, it's the last thing you'll see
+ */
+ if (ei_local->dmaing) {
+ netdev_err(dev,
+ "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
+ __func__, ei_local->dmaing, ei_local->irqlock);
+ return;
+ }
+
+ ei_local->dmaing |= 0x01;
+ /* We should already be in page 0, but to be safe... */
+ ei_outb(E8390_PAGE0 + E8390_START + E8390_NODMA, addr + NE_CMD);
+
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR);
+
+ /* Now the normal output. */
+ ei_outb(count & 0xff, addr + NE_EN0_RCNTLO);
+ ei_outb(count >> 8, addr + NE_EN0_RCNTHI);
+ ei_outb(0x00, addr + NE_EN0_RSARLO);
+ ei_outb(start_page, addr + NE_EN0_RSARHI);
+ ei_outb(E8390_RWRITE + E8390_START, addr + NE_CMD);
+
+ ei_outsw(addr + NE_DATAPORT, buf, count >> 1);
+
+ dma_start = jiffies;
+ while ((ei_inb(addr + NE_EN0_ISR) & ENISR_RDC) == 0) {
+ if (time_after(jiffies, dma_start + 2 * HZ / 100)) { /* 20ms */
+ netdev_err(dev, "timeout waiting for Tx RDC\n");
+ mcf8390_reset_8390(dev);
+ __NS8390_init(dev, 1);
+ break;
+ }
+ }
+
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR); /* Ack intr */
+ ei_local->dmaing &= ~0x01;
+}
+
+static const struct net_device_ops mcf8390_netdev_ops = {
+ .ndo_open = __ei_open,
+ .ndo_stop = __ei_close,
+ .ndo_start_xmit = __ei_start_xmit,
+ .ndo_tx_timeout = __ei_tx_timeout,
+ .ndo_get_stats = __ei_get_stats,
+ .ndo_set_rx_mode = __ei_set_multicast_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = __ei_poll,
+#endif
+};
+
+static int mcf8390_init(struct net_device *dev)
+{
+ static u32 offsets[] = {
+ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
+ 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+ };
+ struct ei_device *ei_local = netdev_priv(dev);
+ unsigned char SA_prom[32];
+ u32 addr = dev->base_addr;
+ int start_page, stop_page;
+ int i, ret;
+
+ mcf8390_reset_8390(dev);
+
+ /*
+ * Read the 16 bytes of station address PROM.
+ * We must first initialize registers,
+ * similar to NS8390_init(eifdev, 0).
+ * We can't reliably read the SAPROM address without this.
+ * (I learned the hard way!).
+ */
+ {
+ static const struct {
+ u32 value;
+ u32 offset;
+ } program_seq[] = {
+ {E8390_NODMA + E8390_PAGE0 + E8390_STOP, NE_CMD},
+ /* Select page 0 */
+ {0x48, NE_EN0_DCFG}, /* 0x48: Set byte-wide access */
+ {0x00, NE_EN0_RCNTLO}, /* Clear the count regs */
+ {0x00, NE_EN0_RCNTHI},
+ {0x00, NE_EN0_IMR}, /* Mask completion irq */
+ {0xFF, NE_EN0_ISR},
+ {E8390_RXOFF, NE_EN0_RXCR}, /* 0x20 Set to monitor */
+ {E8390_TXOFF, NE_EN0_TXCR}, /* 0x02 and loopback mode */
+ {32, NE_EN0_RCNTLO},
+ {0x00, NE_EN0_RCNTHI},
+ {0x00, NE_EN0_RSARLO}, /* DMA starting at 0x0000 */
+ {0x00, NE_EN0_RSARHI},
+ {E8390_RREAD + E8390_START, NE_CMD},
+ };
+ for (i = 0; i < ARRAY_SIZE(program_seq); i++) {
+ ei_outb(program_seq[i].value,
+ addr + program_seq[i].offset);
+ }
+ }
+
+ for (i = 0; i < 16; i++) {
+ SA_prom[i] = ei_inb(addr + NE_DATAPORT);
+ ei_inb(addr + NE_DATAPORT);
+ }
+
+ /* We must set the 8390 for word mode. */
+ ei_outb(0x49, addr + NE_EN0_DCFG);
+ start_page = NESM_START_PG;
+ stop_page = NESM_STOP_PG;
+
+ /* Install the Interrupt handler */
+ ret = request_irq(dev->irq, __ei_interrupt, 0, dev->name, dev);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < ETH_ALEN; i++)
+ dev->dev_addr[i] = SA_prom[i];
+
+ pr_debug("Found ethernet address: %pM\n", dev->dev_addr);
+
+ ei_local->name = "mcf8390";
+ ei_local->tx_start_page = start_page;
+ ei_local->stop_page = stop_page;
+ ei_local->word16 = 1;
+ ei_local->rx_start_page = start_page + TX_PAGES;
+ ei_local->reset_8390 = mcf8390_reset_8390;
+ ei_local->block_input = mcf8390_block_input;
+ ei_local->block_output = mcf8390_block_output;
+ ei_local->get_8390_hdr = mcf8390_get_8390_hdr;
+ ei_local->reg_offset = offsets;
+
+ dev->netdev_ops = &mcf8390_netdev_ops;
+ __NS8390_init(dev, 0);
+ ret = register_netdev(dev);
+ if (ret) {
+ free_irq(dev->irq, dev);
+ return ret;
+ }
+
+ netdev_info(dev, "addr=0x%08x irq=%d, Ethernet Address %pM\n",
+ addr, dev->irq, dev->dev_addr);
+ return 0;
+}
+
+static int mcf8390_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct ei_device *ei_local;
+ struct resource *mem, *irq;
+ resource_size_t msize;
+ int ret;
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (irq == NULL) {
+ dev_err(&pdev->dev, "no IRQ specified?\n");
+ return -ENXIO;
+ }
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (mem == NULL) {
+ dev_err(&pdev->dev, "no memory address specified?\n");
+ return -ENXIO;
+ }
+ msize = resource_size(mem);
+ if (!request_mem_region(mem->start, msize, pdev->name))
+ return -EBUSY;
+
+ dev = ____alloc_ei_netdev(0);
+ if (dev == NULL) {
+ release_mem_region(mem->start, msize);
+ return -ENOMEM;
+ }
+
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ platform_set_drvdata(pdev, dev);
+ ei_local = netdev_priv(dev);
+
+ dev->irq = irq->start;
+ dev->base_addr = mem->start;
+
+ ret = mcf8390_init(dev);
+ if (ret) {
+ release_mem_region(mem->start, msize);
+ free_netdev(dev);
+ return ret;
+ }
+ return 0;
+}
+
+static int mcf8390_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct resource *mem;
+
+ unregister_netdev(dev);
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (mem)
+ release_mem_region(mem->start, resource_size(mem));
+ free_netdev(dev);
+ return 0;
+}
+
+static struct platform_driver mcf8390_drv = {
+ .driver = {
+ .name = "mcf8390",
+ .owner = THIS_MODULE,
+ },
+ .probe = mcf8390_probe,
+ .remove = mcf8390_remove,
+};
+
+module_platform_driver(mcf8390_drv);
+
+MODULE_DESCRIPTION("MCF8390 ColdFire NS8390 driver");
+MODULE_AUTHOR("Greg Ungerer <gerg@uclinux.org>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mcf8390");
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
@ 2012-07-04 4:56 ` gerg
0 siblings, 0 replies; 14+ messages in thread
From: gerg @ 2012-07-04 4:56 UTC (permalink / raw)
To: netdev, linux-m68k; +Cc: Greg Ungerer
From: Greg Ungerer <gerg@uclinux.org>
A number of older ColdFire CPU based boards use NS8390 based network
controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
provides the support code to get these devices working on these platforms.
Generally the NS8390 based eth device is direct connected via the general
purpose bus of the ColdFire CPU. So its addressing and interrupt setup is
fixed on each of the different platforms (classic platform setup).
This driver is based on the other drivers/net/ethernet/8390 drivers, and
includes the lib8390.c code. It uses the existing definitions of the
board NS8390 device addresses, interrupts and access types from the
arch/m68k/include/asm/mcf8390.h, but moves the IO access functions into
the driver code and out of that header.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
---
arch/m68k/include/asm/mcf8390.h | 129 +---------
drivers/net/ethernet/8390/Kconfig | 14 +
drivers/net/ethernet/8390/Makefile | 1 +
drivers/net/ethernet/8390/mcf8390.c | 478 +++++++++++++++++++++++++++++++++++
4 files changed, 502 insertions(+), 120 deletions(-)
create mode 100644 drivers/net/ethernet/8390/mcf8390.c
diff --git a/arch/m68k/include/asm/mcf8390.h b/arch/m68k/include/asm/mcf8390.h
index bf3d97b..a72a208 100644
--- a/arch/m68k/include/asm/mcf8390.h
+++ b/arch/m68k/include/asm/mcf8390.h
@@ -37,6 +37,7 @@
#if defined(CONFIG_ARN5206)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0xf0
#define NE2000_IRQ_PRIORITY 2
#define NE2000_IRQ_LEVEL 4
@@ -46,6 +47,7 @@
#if defined(CONFIG_M5206eC3)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1c
#define NE2000_IRQ_PRIORITY 2
#define NE2000_IRQ_LEVEL 4
@@ -54,6 +56,7 @@
#if defined(CONFIG_M5206e) && defined(CONFIG_NETtel)
#define NE2000_ADDR 0x30000300
+#define NE2000_ADDRSIZE 0x00001000
#define NE2000_IRQ_VECTOR 25
#define NE2000_IRQ_PRIORITY 1
#define NE2000_IRQ_LEVEL 3
@@ -63,6 +66,7 @@
#if defined(CONFIG_M5307C3)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1b
#define NE2000_BYTE volatile unsigned short
#endif
@@ -70,6 +74,7 @@
#if defined(CONFIG_M5272) && defined(CONFIG_NETtel)
#define NE2000_ADDR 0x30600300
#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_ADDRSIZE 0x00010000
#define NE2000_IRQ_VECTOR 67
#undef BSWAP
#define BSWAP(w) (w)
@@ -82,6 +87,7 @@
#define NE2000_ADDR0 0x30600300
#define NE2000_ADDR1 0x30800300
#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_ADDRSIZE 0x00010000
#define NE2000_IRQ_VECTOR0 27
#define NE2000_IRQ_VECTOR1 29
#undef BSWAP
@@ -94,6 +100,7 @@
#if defined(CONFIG_M5307) && defined(CONFIG_SECUREEDGEMP3)
#define NE2000_ADDR 0x30600300
#define NE2000_ODDOFFSET 0x00008000
+#define NE2000_ADDRSIZE 0x00010000
#define NE2000_IRQ_VECTOR 27
#undef BSWAP
#define BSWAP(w) (w)
@@ -105,6 +112,7 @@
#if defined(CONFIG_ARN5307)
#define NE2000_ADDR 0xfe600300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1b
#define NE2000_IRQ_PRIORITY 2
#define NE2000_IRQ_LEVEL 3
@@ -114,129 +122,10 @@
#if defined(CONFIG_M5407C3)
#define NE2000_ADDR 0x40000300
#define NE2000_ODDOFFSET 0x00010000
+#define NE2000_ADDRSIZE 0x00020000
#define NE2000_IRQ_VECTOR 0x1b
#define NE2000_BYTE volatile unsigned short
#endif
/****************************************************************************/
-
-/*
- * Side-band address space for odd address requires re-mapping
- * many of the standard ISA access functions.
- */
-#ifdef NE2000_ODDOFFSET
-
-#undef outb
-#undef outb_p
-#undef inb
-#undef inb_p
-#undef outsb
-#undef outsw
-#undef insb
-#undef insw
-
-#define outb ne2000_outb
-#define inb ne2000_inb
-#define outb_p ne2000_outb
-#define inb_p ne2000_inb
-#define outsb ne2000_outsb
-#define outsw ne2000_outsw
-#define insb ne2000_insb
-#define insw ne2000_insw
-
-
-#ifndef COLDFIRE_NE2000_FUNCS
-
-void ne2000_outb(unsigned int val, unsigned int addr);
-int ne2000_inb(unsigned int addr);
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len);
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsb(unsigned int addr, void *vbuf, unsigned long len);
-void ne2000_outsw(unsigned int addr, void *vbuf, unsigned long len);
-
-#else
-
-/*
- * This macro converts a conventional register address into the
- * real memory pointer of the mapped NE2000 device.
- * On most NE2000 implementations on ColdFire boards the chip is
- * mapped in kinda funny, due to its ISA heritage.
- */
-#define NE2000_PTR(addr) ((addr&0x1)?(NE2000_ODDOFFSET+addr-1):(addr))
-#define NE2000_DATA_PTR(addr) (addr)
-
-
-void ne2000_outb(unsigned int val, unsigned int addr)
-{
- NE2000_BYTE *rp;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- *rp = RSWAP(val);
-}
-
-int ne2000_inb(unsigned int addr)
-{
- NE2000_BYTE *rp, val;
-
- rp = (NE2000_BYTE *) NE2000_PTR(addr);
- val = *rp;
- return((int) ((NE2000_BYTE) RSWAP(val)));
-}
-
-void ne2000_insb(unsigned int addr, void *vbuf, int unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *rp;
- *buf++ = RSWAP(val);
- }
-}
-
-void ne2000_insw(unsigned int addr, void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *rp;
- *buf++ = BSWAP(w);
- }
-}
-
-void ne2000_outsb(unsigned int addr, const void *vbuf, unsigned long len)
-{
- NE2000_BYTE *rp, val;
- unsigned char *buf;
-
- buf = (unsigned char *) vbuf;
- rp = (NE2000_BYTE *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- val = *buf++;
- *rp = RSWAP(val);
- }
-}
-
-void ne2000_outsw(unsigned int addr, const void *vbuf, unsigned long len)
-{
- volatile unsigned short *rp;
- unsigned short w, *buf;
-
- buf = (unsigned short *) vbuf;
- rp = (volatile unsigned short *) NE2000_DATA_PTR(addr);
- for (; (len > 0); len--) {
- w = *buf++;
- *rp = BSWAP(w);
- }
-}
-
-#endif /* COLDFIRE_NE2000_FUNCS */
-#endif /* NE2000_OFFOFFSET */
-
-/****************************************************************************/
#endif /* mcf8390_h */
diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index 2e53867..e1219e0 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -162,6 +162,20 @@ config MAC8390
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
+config MCF8390
+ tristate "ColdFire NS8390 based Ethernet support"
+ depends on COLDFIRE
+ select CRC32
+ ---help---
+ This driver is for Ethernet devices using an NS8390-compatible
+ chipset on many common ColdFire CPU based boards. Many of the older
+ Freescale dev boards use this, and some other common boards like
+ some SnapGear routers do as well.
+
+ If you have one of these boards and want to use the network interface
+ on them then choose Y. To compile this driver as a module, choose M
+ here, the module will be called mcf8390.
+
config NE2000
tristate "NE2000/NE1000 support"
depends on (ISA || (Q40 && m) || M32R || MACH_TX49XX)
diff --git a/drivers/net/ethernet/8390/Makefile b/drivers/net/ethernet/8390/Makefile
index d13790b..f43038b 100644
--- a/drivers/net/ethernet/8390/Makefile
+++ b/drivers/net/ethernet/8390/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390p.o
obj-$(CONFIG_HPLAN) += hp.o 8390p.o
obj-$(CONFIG_HYDRA) += hydra.o 8390.o
obj-$(CONFIG_LNE390) += lne390.o 8390.o
+obj-$(CONFIG_MCF8390) += mcf8390.o 8390.o
obj-$(CONFIG_NE2000) += ne.o 8390p.o
obj-$(CONFIG_NE2_MCA) += ne2.o 8390p.o
obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c
new file mode 100644
index 0000000..12b3d40
--- /dev/null
+++ b/drivers/net/ethernet/8390/mcf8390.c
@@ -0,0 +1,478 @@
+/*
+ * Support for ColdFire CPU based boards using a NS8390 Ethernet device.
+ *
+ * Derived from the many other 8390 drivers.
+ *
+ * (C) Copyright 2012, Greg Ungerer <gerg@uclinux.org>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of the Linux
+ * distribution for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/jiffies.h>
+#include <linux/io.h>
+#include <asm/mcf8390.h>
+
+static const char version[] =
+ "mcf8390.c: (15-06-2012) Greg Ungerer <gerg@uclinux.org>";
+
+#define NE_CMD 0x00
+#define NE_DATAPORT 0x10 /* NatSemi-defined port window offset */
+#define NE_RESET 0x1f /* Issue a read to reset ,a write to clear */
+#define NE_EN0_ISR 0x07
+#define NE_EN0_DCFG 0x0e
+#define NE_EN0_RSARLO 0x08
+#define NE_EN0_RSARHI 0x09
+#define NE_EN0_RCNTLO 0x0a
+#define NE_EN0_RXCR 0x0c
+#define NE_EN0_TXCR 0x0d
+#define NE_EN0_RCNTHI 0x0b
+#define NE_EN0_IMR 0x0f
+
+#define NESM_START_PG 0x40 /* First page of TX buffer */
+#define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */
+
+#ifdef NE2000_ODDOFFSET
+/*
+ * A lot of the ColdFire boards use a separate address region for odd offset
+ * register addresses. The following macros and functions convert and map
+ * as required. Note that the data port accesses are treated a little
+ * differently, and always accessed via the insX/outsX functions.
+ */
+#define NE_PTR(a) (((a) & 0x1) ? (NE2000_ODDOFFSET + (a) - 1) : (a))
+#define NE_DATA_PTR(a) (a)
+
+void ei_outb(u32 val, u32 addr)
+{
+ NE2000_BYTE *rp;
+
+ rp = (NE2000_BYTE *) NE_PTR(addr);
+ *rp = RSWAP(val);
+}
+
+#define ei_inb ei_inb
+u8 ei_inb(u32 addr)
+{
+ NE2000_BYTE *rp, val;
+
+ rp = (NE2000_BYTE *) NE_PTR(addr);
+ val = *rp;
+ return (u8) (RSWAP(val) & 0xff);
+}
+
+void ei_insb(u32 addr, void *vbuf, int len)
+{
+ NE2000_BYTE *rp, val;
+ u8 *buf;
+
+ buf = (u8 *) vbuf;
+ rp = (NE2000_BYTE *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *rp;
+ *buf++ = RSWAP(val);
+ }
+}
+
+void ei_insw(u32 addr, void *vbuf, int len)
+{
+ volatile u16 *rp;
+ u16 w, *buf;
+
+ buf = (u16 *) vbuf;
+ rp = (volatile u16 *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *rp;
+ *buf++ = BSWAP(w);
+ }
+}
+
+void ei_outsb(u32 addr, const void *vbuf, int len)
+{
+ NE2000_BYTE *rp, val;
+ u8 *buf;
+
+ buf = (u8 *) vbuf;
+ rp = (NE2000_BYTE *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ val = *buf++;
+ *rp = RSWAP(val);
+ }
+}
+
+void ei_outsw(u32 addr, const void *vbuf, int len)
+{
+ volatile u16 *rp;
+ u16 w, *buf;
+
+ buf = (u16 *) vbuf;
+ rp = (volatile u16 *) NE_DATA_PTR(addr);
+ for (; (len > 0); len--) {
+ w = *buf++;
+ *rp = BSWAP(w);
+ }
+}
+
+#else /* !NE2000_ODDOFFSET */
+
+#define ei_inb inb
+#define ei_outb outb
+#define ei_insb insb
+#define ei_insw insw
+#define ei_outsb outsb
+#define ei_outsw outsw
+
+#endif /* !NE2000_ODDOFFSET */
+
+#define ei_inb_p ei_inb
+#define ei_outb_p ei_outb
+
+#include "lib8390.c"
+
+/*
+ * Hard reset the card. This used to pause for the same period that a
+ * 8390 reset command required, but that shouldn't be necessary.
+ */
+static void mcf8390_reset_8390(struct net_device *dev)
+{
+ unsigned long reset_start_time = jiffies;
+ u32 addr = dev->base_addr;
+
+ if (ei_debug > 1)
+ netdev_dbg(dev, "resetting the 8390 t=%ld...\n", jiffies);
+
+ ei_outb(ei_inb(addr + NE_RESET), addr + NE_RESET);
+
+ ei_status.txing = 0;
+ ei_status.dmaing = 0;
+
+ /* This check _should_not_ be necessary, omit eventually. */
+ while ((ei_inb(addr + NE_EN0_ISR) & ENISR_RESET) == 0) {
+ if (time_after(jiffies, reset_start_time + 2 * HZ / 100)) {
+ netdev_warn(dev, "%s: did not complete\n", __func__);
+ break;
+ }
+ }
+
+ ei_outb(ENISR_RESET, addr + NE_EN0_ISR);
+}
+
+/*
+ * Grab the 8390 specific header. Similar to the block_input routine, but
+ * we don't need to be concerned with ring wrap as the header will be at
+ * the start of a page, so we optimize accordingly.
+ */
+static void mcf8390_get_8390_hdr(struct net_device *dev,
+ struct e8390_pkt_hdr *hdr, int ring_page)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ u32 addr = dev->base_addr;
+
+ /*
+ * This *shouldn't* happen.
+ * If it does, it's the last thing you'll see
+ */
+ if (ei_status.dmaing) {
+ netdev_err(dev,
+ "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
+ __func__, ei_local->dmaing, ei_local->irqlock);
+ return;
+ }
+
+ ei_local->dmaing |= 0x01;
+ ei_outb(E8390_NODMA + E8390_PAGE0 + E8390_START, addr + NE_CMD);
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR);
+ ei_outb(sizeof(struct e8390_pkt_hdr), addr + NE_EN0_RCNTLO);
+ ei_outb(0, addr + NE_EN0_RCNTHI);
+ ei_outb(0, addr + NE_EN0_RSARLO); /* On page boundary */
+ ei_outb(ring_page, addr + NE_EN0_RSARHI);
+ ei_outb(E8390_RREAD + E8390_START, addr + NE_CMD);
+
+ ei_insw(addr + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr) >> 1);
+
+ outb(ENISR_RDC, addr + NE_EN0_ISR); /* Ack intr */
+ ei_local->dmaing &= ~0x01;
+
+ hdr->count = cpu_to_le16(hdr->count);
+}
+
+/*
+ * Block input and output, similar to the Crynwr packet driver.
+ * If you are porting to a new ethercard, look at the packet driver source
+ * for hints. The NEx000 doesn't share the on-board packet memory --
+ * you have to put the packet out through the "remote DMA" dataport
+ * using z_writeb.
+ */
+static void mcf8390_block_input(struct net_device *dev, int count,
+ struct sk_buff *skb, int ring_offset)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ u32 addr = dev->base_addr;
+ char *buf = skb->data;
+
+ /*
+ * This *shouldn't* happen.
+ * If it does, it's the last thing you'll see
+ */
+ if (ei_local->dmaing) {
+ netdev_err(dev,
+ "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
+ __func__, ei_local->dmaing, ei_local->irqlock);
+ return;
+ }
+
+ ei_local->dmaing |= 0x01;
+ ei_outb(E8390_NODMA + E8390_PAGE0 + E8390_START, addr + NE_CMD);
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR);
+ ei_outb(count & 0xff, addr + NE_EN0_RCNTLO);
+ ei_outb(count >> 8, addr + NE_EN0_RCNTHI);
+ ei_outb(ring_offset & 0xff, addr + NE_EN0_RSARLO);
+ ei_outb(ring_offset >> 8, addr + NE_EN0_RSARHI);
+ ei_outb(E8390_RREAD + E8390_START, addr + NE_CMD);
+
+ ei_insw(addr + NE_DATAPORT, buf, count >> 1);
+ if (count & 1)
+ buf[count - 1] = ei_inb(addr + NE_DATAPORT);
+
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR); /* Ack intr */
+ ei_local->dmaing &= ~0x01;
+}
+
+static void mcf8390_block_output(struct net_device *dev, int count,
+ const unsigned char *buf,
+ const int start_page)
+{
+ struct ei_device *ei_local = netdev_priv(dev);
+ u32 addr = dev->base_addr;
+ unsigned long dma_start;
+
+ /* Make sure we transfer all bytes if 16bit IO writes */
+ if (count & 0x1)
+ count++;
+
+ /*
+ *This *shouldn't* happen.
+ * If it does, it's the last thing you'll see
+ */
+ if (ei_local->dmaing) {
+ netdev_err(dev,
+ "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
+ __func__, ei_local->dmaing, ei_local->irqlock);
+ return;
+ }
+
+ ei_local->dmaing |= 0x01;
+ /* We should already be in page 0, but to be safe... */
+ ei_outb(E8390_PAGE0 + E8390_START + E8390_NODMA, addr + NE_CMD);
+
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR);
+
+ /* Now the normal output. */
+ ei_outb(count & 0xff, addr + NE_EN0_RCNTLO);
+ ei_outb(count >> 8, addr + NE_EN0_RCNTHI);
+ ei_outb(0x00, addr + NE_EN0_RSARLO);
+ ei_outb(start_page, addr + NE_EN0_RSARHI);
+ ei_outb(E8390_RWRITE + E8390_START, addr + NE_CMD);
+
+ ei_outsw(addr + NE_DATAPORT, buf, count >> 1);
+
+ dma_start = jiffies;
+ while ((ei_inb(addr + NE_EN0_ISR) & ENISR_RDC) == 0) {
+ if (time_after(jiffies, dma_start + 2 * HZ / 100)) { /* 20ms */
+ netdev_err(dev, "timeout waiting for Tx RDC\n");
+ mcf8390_reset_8390(dev);
+ __NS8390_init(dev, 1);
+ break;
+ }
+ }
+
+ ei_outb(ENISR_RDC, addr + NE_EN0_ISR); /* Ack intr */
+ ei_local->dmaing &= ~0x01;
+}
+
+static const struct net_device_ops mcf8390_netdev_ops = {
+ .ndo_open = __ei_open,
+ .ndo_stop = __ei_close,
+ .ndo_start_xmit = __ei_start_xmit,
+ .ndo_tx_timeout = __ei_tx_timeout,
+ .ndo_get_stats = __ei_get_stats,
+ .ndo_set_rx_mode = __ei_set_multicast_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = __ei_poll,
+#endif
+};
+
+static int mcf8390_init(struct net_device *dev)
+{
+ static u32 offsets[] = {
+ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
+ 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
+ };
+ struct ei_device *ei_local = netdev_priv(dev);
+ unsigned char SA_prom[32];
+ u32 addr = dev->base_addr;
+ int start_page, stop_page;
+ int i, ret;
+
+ mcf8390_reset_8390(dev);
+
+ /*
+ * Read the 16 bytes of station address PROM.
+ * We must first initialize registers,
+ * similar to NS8390_init(eifdev, 0).
+ * We can't reliably read the SAPROM address without this.
+ * (I learned the hard way!).
+ */
+ {
+ static const struct {
+ u32 value;
+ u32 offset;
+ } program_seq[] = {
+ {E8390_NODMA + E8390_PAGE0 + E8390_STOP, NE_CMD},
+ /* Select page 0 */
+ {0x48, NE_EN0_DCFG}, /* 0x48: Set byte-wide access */
+ {0x00, NE_EN0_RCNTLO}, /* Clear the count regs */
+ {0x00, NE_EN0_RCNTHI},
+ {0x00, NE_EN0_IMR}, /* Mask completion irq */
+ {0xFF, NE_EN0_ISR},
+ {E8390_RXOFF, NE_EN0_RXCR}, /* 0x20 Set to monitor */
+ {E8390_TXOFF, NE_EN0_TXCR}, /* 0x02 and loopback mode */
+ {32, NE_EN0_RCNTLO},
+ {0x00, NE_EN0_RCNTHI},
+ {0x00, NE_EN0_RSARLO}, /* DMA starting at 0x0000 */
+ {0x00, NE_EN0_RSARHI},
+ {E8390_RREAD + E8390_START, NE_CMD},
+ };
+ for (i = 0; i < ARRAY_SIZE(program_seq); i++) {
+ ei_outb(program_seq[i].value,
+ addr + program_seq[i].offset);
+ }
+ }
+
+ for (i = 0; i < 16; i++) {
+ SA_prom[i] = ei_inb(addr + NE_DATAPORT);
+ ei_inb(addr + NE_DATAPORT);
+ }
+
+ /* We must set the 8390 for word mode. */
+ ei_outb(0x49, addr + NE_EN0_DCFG);
+ start_page = NESM_START_PG;
+ stop_page = NESM_STOP_PG;
+
+ /* Install the Interrupt handler */
+ ret = request_irq(dev->irq, __ei_interrupt, 0, dev->name, dev);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < ETH_ALEN; i++)
+ dev->dev_addr[i] = SA_prom[i];
+
+ pr_debug("Found ethernet address: %pM\n", dev->dev_addr);
+
+ ei_local->name = "mcf8390";
+ ei_local->tx_start_page = start_page;
+ ei_local->stop_page = stop_page;
+ ei_local->word16 = 1;
+ ei_local->rx_start_page = start_page + TX_PAGES;
+ ei_local->reset_8390 = mcf8390_reset_8390;
+ ei_local->block_input = mcf8390_block_input;
+ ei_local->block_output = mcf8390_block_output;
+ ei_local->get_8390_hdr = mcf8390_get_8390_hdr;
+ ei_local->reg_offset = offsets;
+
+ dev->netdev_ops = &mcf8390_netdev_ops;
+ __NS8390_init(dev, 0);
+ ret = register_netdev(dev);
+ if (ret) {
+ free_irq(dev->irq, dev);
+ return ret;
+ }
+
+ netdev_info(dev, "addr=0x%08x irq=%d, Ethernet Address %pM\n",
+ addr, dev->irq, dev->dev_addr);
+ return 0;
+}
+
+static int mcf8390_probe(struct platform_device *pdev)
+{
+ struct net_device *dev;
+ struct ei_device *ei_local;
+ struct resource *mem, *irq;
+ resource_size_t msize;
+ int ret;
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (irq == NULL) {
+ dev_err(&pdev->dev, "no IRQ specified?\n");
+ return -ENXIO;
+ }
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (mem == NULL) {
+ dev_err(&pdev->dev, "no memory address specified?\n");
+ return -ENXIO;
+ }
+ msize = resource_size(mem);
+ if (!request_mem_region(mem->start, msize, pdev->name))
+ return -EBUSY;
+
+ dev = ____alloc_ei_netdev(0);
+ if (dev == NULL) {
+ release_mem_region(mem->start, msize);
+ return -ENOMEM;
+ }
+
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ platform_set_drvdata(pdev, dev);
+ ei_local = netdev_priv(dev);
+
+ dev->irq = irq->start;
+ dev->base_addr = mem->start;
+
+ ret = mcf8390_init(dev);
+ if (ret) {
+ release_mem_region(mem->start, msize);
+ free_netdev(dev);
+ return ret;
+ }
+ return 0;
+}
+
+static int mcf8390_remove(struct platform_device *pdev)
+{
+ struct net_device *dev = platform_get_drvdata(pdev);
+ struct resource *mem;
+
+ unregister_netdev(dev);
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (mem)
+ release_mem_region(mem->start, resource_size(mem));
+ free_netdev(dev);
+ return 0;
+}
+
+static struct platform_driver mcf8390_drv = {
+ .driver = {
+ .name = "mcf8390",
+ .owner = THIS_MODULE,
+ },
+ .probe = mcf8390_probe,
+ .remove = mcf8390_remove,
+};
+
+module_platform_driver(mcf8390_drv);
+
+MODULE_DESCRIPTION("MCF8390 ColdFire NS8390 driver");
+MODULE_AUTHOR("Greg Ungerer <gerg@uclinux.org>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mcf8390");
--
1.7.0.4
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 4:56 ` gerg
(?)
@ 2012-07-04 5:18 ` Joe Perches
2012-07-04 6:18 ` Greg Ungerer
-1 siblings, 1 reply; 14+ messages in thread
From: Joe Perches @ 2012-07-04 5:18 UTC (permalink / raw)
To: gerg; +Cc: netdev, linux-m68k, Greg Ungerer
On Wed, 2012-07-04 at 14:56 +1000, gerg@snapgear.com wrote:
> From: Greg Ungerer <gerg@uclinux.org>
>
> A number of older ColdFire CPU based boards use NS8390 based network
> controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
> provides the support code to get these devices working on these platforms.
Hi Greg, just some trivia:
[]
> diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c
[]
> +#ifdef NE2000_ODDOFFSET
> +/*
> + * A lot of the ColdFire boards use a separate address region for odd offset
> + * register addresses. The following macros and functions convert and map
> + * as required. Note that the data port accesses are treated a little
> + * differently, and always accessed via the insX/outsX functions.
> + */
> +#define NE_PTR(a) (((a) & 0x1) ? (NE2000_ODDOFFSET + (a) - 1) : (a))
Maybe use static inlines instead of macros?
static inline void *NE_PTR(void *ptr)
{
if ((unsigned long)ptr & 1)
return ptr - 1 + NE2000_ODDOFFSET;
return ptr;
}
[]
> +static void mcf8390_get_8390_hdr(struct net_device *dev,
> + struct e8390_pkt_hdr *hdr, int ring_page)
> +{
[]
> + /*
> + * This *shouldn't* happen.
> + * If it does, it's the last thing you'll see
> + */
> + if (ei_status.dmaing) {
> + netdev_err(dev,
> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
> + __func__, ei_local->dmaing, ei_local->irqlock);
This message seems to get repeated a few times.
Maybe another function/macro or maybe a BUG?
some_dma_err(dev, __func__, ei_local);
> +static void mcf8390_block_input(struct net_device *dev, int count,
> + struct sk_buff *skb, int ring_offset)
> +{
[]
> + /*
> + * This *shouldn't* happen.
> + * If it does, it's the last thing you'll see
> + */
> + if (ei_local->dmaing) {
> + netdev_err(dev,
> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
> + __func__, ei_local->dmaing, ei_local->irqlock);
> + return;
> + }
> +static void mcf8390_block_output(struct net_device *dev, int count,
> + const unsigned char *buf,
> + const int start_page)
> +{
[]
> + /*
> + *This *shouldn't* happen.
> + * If it does, it's the last thing you'll see
> + */
> + if (ei_local->dmaing) {
> + netdev_err(dev,
> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
> + __func__, ei_local->dmaing, ei_local->irqlock);
> + return;
> + }
> +static int mcf8390_init(struct net_device *dev)
> +{
> + static u32 offsets[] = {
> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
> + };
const? u8?
> + pr_debug("Found ethernet address: %pM\n", dev->dev_addr);
netdev_dbg ?
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 5:18 ` Joe Perches
@ 2012-07-04 6:18 ` Greg Ungerer
0 siblings, 0 replies; 14+ messages in thread
From: Greg Ungerer @ 2012-07-04 6:18 UTC (permalink / raw)
To: Joe Perches; +Cc: netdev, linux-m68k, Greg Ungerer
Hi Joe,
On 04/07/12 15:18, Joe Perches wrote:
> On Wed, 2012-07-04 at 14:56 +1000, gerg@snapgear.com wrote:
>> From: Greg Ungerer <gerg@uclinux.org>
>>
>> A number of older ColdFire CPU based boards use NS8390 based network
>> controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
>> provides the support code to get these devices working on these platforms.
>
> Hi Greg, just some trivia:
Thanks for the quick feedback!
> []
>
>> diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c
>
> []
>
>> +#ifdef NE2000_ODDOFFSET
>> +/*
>> + * A lot of the ColdFire boards use a separate address region for odd offset
>> + * register addresses. The following macros and functions convert and map
>> + * as required. Note that the data port accesses are treated a little
>> + * differently, and always accessed via the insX/outsX functions.
>> + */
>> +#define NE_PTR(a) (((a) & 0x1) ? (NE2000_ODDOFFSET + (a) - 1) : (a))
>
> Maybe use static inlines instead of macros?
>
> static inline void *NE_PTR(void *ptr)
> {
> if ((unsigned long)ptr & 1)
> return ptr - 1 + NE2000_ODDOFFSET;
> return ptr;
> }
Ok, that looks better. Though I might make the arg u32, which matches
the way that the address is passed to the IO functions currently.
> []
>
>> +static void mcf8390_get_8390_hdr(struct net_device *dev,
>> + struct e8390_pkt_hdr *hdr, int ring_page)
>> +{
> []
>> + /*
>> + * This *shouldn't* happen.
>> + * If it does, it's the last thing you'll see
>> + */
>> + if (ei_status.dmaing) {
>> + netdev_err(dev,
>> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
>> + __func__, ei_local->dmaing, ei_local->irqlock);
>
> This message seems to get repeated a few times.
> Maybe another function/macro or maybe a BUG?
>
> some_dma_err(dev, __func__, ei_local);
Yep, sure thing. I copied that part "as is", and a few of the other
drivers seem to have it done this way too. No excuses though :-)
>> +static void mcf8390_block_input(struct net_device *dev, int count,
>> + struct sk_buff *skb, int ring_offset)
>> +{
> []
>> + /*
>> + * This *shouldn't* happen.
>> + * If it does, it's the last thing you'll see
>> + */
>> + if (ei_local->dmaing) {
>> + netdev_err(dev,
>> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
>> + __func__, ei_local->dmaing, ei_local->irqlock);
>> + return;
>> + }
>
>> +static void mcf8390_block_output(struct net_device *dev, int count,
>> + const unsigned char *buf,
>> + const int start_page)
>> +{
> []
>> + /*
>> + *This *shouldn't* happen.
>> + * If it does, it's the last thing you'll see
>> + */
>> + if (ei_local->dmaing) {
>> + netdev_err(dev,
>> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
>> + __func__, ei_local->dmaing, ei_local->irqlock);
>> + return;
>> + }
>
>> +static int mcf8390_init(struct net_device *dev)
>> +{
>> + static u32 offsets[] = {
>> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
>> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
>> + };
>
> const? u8?
That is assigned to the "reg_offset" field of "struct ei_device"
(defined in the existing 8390.h) and that is:
u32 *reg_offset; /* Register mapping table */
So I can't change this.
>> + pr_debug("Found ethernet address: %pM\n", dev->dev_addr);
>
> netdev_dbg ?
Sure, will change it.
Thanks for the quick feedback, much appreciated.
I'll send a revised patch in 24 hours or so.
Regards
Greg
------------------------------------------------------------------------
Greg Ungerer -- Principal Engineer EMAIL: gerg@snapgear.com
SnapGear Group, McAfee PHONE: +61 7 3435 2888
8 Gardner Close FAX: +61 7 3217 5323
Milton, QLD, 4064, Australia WEB: http://www.SnapGear.com
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
@ 2012-07-04 6:18 ` Greg Ungerer
0 siblings, 0 replies; 14+ messages in thread
From: Greg Ungerer @ 2012-07-04 6:18 UTC (permalink / raw)
To: Joe Perches; +Cc: netdev, linux-m68k, Greg Ungerer
Hi Joe,
On 04/07/12 15:18, Joe Perches wrote:
> On Wed, 2012-07-04 at 14:56 +1000, gerg@snapgear.com wrote:
>> From: Greg Ungerer <gerg@uclinux.org>
>>
>> A number of older ColdFire CPU based boards use NS8390 based network
>> controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
>> provides the support code to get these devices working on these platforms.
>
> Hi Greg, just some trivia:
Thanks for the quick feedback!
> []
>
>> diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c
>
> []
>
>> +#ifdef NE2000_ODDOFFSET
>> +/*
>> + * A lot of the ColdFire boards use a separate address region for odd offset
>> + * register addresses. The following macros and functions convert and map
>> + * as required. Note that the data port accesses are treated a little
>> + * differently, and always accessed via the insX/outsX functions.
>> + */
>> +#define NE_PTR(a) (((a) & 0x1) ? (NE2000_ODDOFFSET + (a) - 1) : (a))
>
> Maybe use static inlines instead of macros?
>
> static inline void *NE_PTR(void *ptr)
> {
> if ((unsigned long)ptr & 1)
> return ptr - 1 + NE2000_ODDOFFSET;
> return ptr;
> }
Ok, that looks better. Though I might make the arg u32, which matches
the way that the address is passed to the IO functions currently.
> []
>
>> +static void mcf8390_get_8390_hdr(struct net_device *dev,
>> + struct e8390_pkt_hdr *hdr, int ring_page)
>> +{
> []
>> + /*
>> + * This *shouldn't* happen.
>> + * If it does, it's the last thing you'll see
>> + */
>> + if (ei_status.dmaing) {
>> + netdev_err(dev,
>> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
>> + __func__, ei_local->dmaing, ei_local->irqlock);
>
> This message seems to get repeated a few times.
> Maybe another function/macro or maybe a BUG?
>
> some_dma_err(dev, __func__, ei_local);
Yep, sure thing. I copied that part "as is", and a few of the other
drivers seem to have it done this way too. No excuses though :-)
>> +static void mcf8390_block_input(struct net_device *dev, int count,
>> + struct sk_buff *skb, int ring_offset)
>> +{
> []
>> + /*
>> + * This *shouldn't* happen.
>> + * If it does, it's the last thing you'll see
>> + */
>> + if (ei_local->dmaing) {
>> + netdev_err(dev,
>> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
>> + __func__, ei_local->dmaing, ei_local->irqlock);
>> + return;
>> + }
>
>> +static void mcf8390_block_output(struct net_device *dev, int count,
>> + const unsigned char *buf,
>> + const int start_page)
>> +{
> []
>> + /*
>> + *This *shouldn't* happen.
>> + * If it does, it's the last thing you'll see
>> + */
>> + if (ei_local->dmaing) {
>> + netdev_err(dev,
>> + "%s: DMAing conflict [DMAstat:%d][irqlock:%d]\n",
>> + __func__, ei_local->dmaing, ei_local->irqlock);
>> + return;
>> + }
>
>> +static int mcf8390_init(struct net_device *dev)
>> +{
>> + static u32 offsets[] = {
>> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
>> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
>> + };
>
> const? u8?
That is assigned to the "reg_offset" field of "struct ei_device"
(defined in the existing 8390.h) and that is:
u32 *reg_offset; /* Register mapping table */
So I can't change this.
>> + pr_debug("Found ethernet address: %pM\n", dev->dev_addr);
>
> netdev_dbg ?
Sure, will change it.
Thanks for the quick feedback, much appreciated.
I'll send a revised patch in 24 hours or so.
Regards
Greg
------------------------------------------------------------------------
Greg Ungerer -- Principal Engineer EMAIL: gerg@snapgear.com
SnapGear Group, McAfee PHONE: +61 7 3435 2888
8 Gardner Close FAX: +61 7 3217 5323
Milton, QLD, 4064, Australia WEB: http://www.SnapGear.com
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 6:18 ` Greg Ungerer
(?)
@ 2012-07-04 6:39 ` Joe Perches
2012-07-04 7:52 ` Geert Uytterhoeven
-1 siblings, 1 reply; 14+ messages in thread
From: Joe Perches @ 2012-07-04 6:39 UTC (permalink / raw)
To: Greg Ungerer; +Cc: netdev, linux-m68k, Greg Ungerer
On Wed, 2012-07-04 at 16:18 +1000, Greg Ungerer wrote:
> Hi Joe,
Hi Greg.
> On 04/07/12 15:18, Joe Perches wrote:
> > On Wed, 2012-07-04 at 14:56 +1000, gerg@snapgear.com wrote:
> >> From: Greg Ungerer <gerg@uclinux.org>
> >>
> >> A number of older ColdFire CPU based boards use NS8390 based network
> >> controllers. Most use the Davicom 9008F or the UMC 9008F. This driver
> >> provides the support code to get these devices working on these platforms.
[]
> >> diff --git a/drivers/net/ethernet/8390/mcf8390.c b/drivers/net/ethernet/8390/mcf8390.c
[]
> >> +static int mcf8390_init(struct net_device *dev)
> >> +{
> >> + static u32 offsets[] = {
> >> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
> >> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
> >> + };
> >
> > const? u8?
>
> That is assigned to the "reg_offset" field of "struct ei_device"
> (defined in the existing 8390.h) and that is:
>
> u32 *reg_offset; /* Register mapping table */
>
> So I can't change this.
Sure you can, you can assign a u8 to a u32 just fine.
The value fits in a u8. Might as well make it take
less data space. static const makes it read-only and
makes the compiler assign it just once instead of at
function invocation.
cheers, Joe
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 6:39 ` Joe Perches
@ 2012-07-04 7:52 ` Geert Uytterhoeven
2012-07-04 8:06 ` Greg Ungerer
2012-07-04 14:52 ` Joe Perches
0 siblings, 2 replies; 14+ messages in thread
From: Geert Uytterhoeven @ 2012-07-04 7:52 UTC (permalink / raw)
To: Joe Perches; +Cc: Greg Ungerer, netdev, linux-m68k, Greg Ungerer
On Wed, Jul 4, 2012 at 8:39 AM, Joe Perches <joe@perches.com> wrote:
>> >> +static int mcf8390_init(struct net_device *dev)
>> >> +{
>> >> + static u32 offsets[] = {
>> >> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
>> >> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
>> >> + };
>> >
>> > const? u8?
>>
>> That is assigned to the "reg_offset" field of "struct ei_device"
>> (defined in the existing 8390.h) and that is:
>>
>> u32 *reg_offset; /* Register mapping table */
>>
>> So I can't change this.
>
> Sure you can, you can assign a u8 to a u32 just fine.
It's not the value that's assigned, but a pointer to the table, so
for now it must be non-const u32 *.
> The value fits in a u8. Might as well make it take
> less data space. static const makes it read-only and
> makes the compiler assign it just once instead of at
> function invocation.
That needs changes to drivers/net/ethernet/8390/8390.h, and
also probably to some drivers that assign values to the array.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 7:52 ` Geert Uytterhoeven
@ 2012-07-04 8:06 ` Greg Ungerer
2012-07-04 14:52 ` Joe Perches
1 sibling, 0 replies; 14+ messages in thread
From: Greg Ungerer @ 2012-07-04 8:06 UTC (permalink / raw)
To: Joe Perches; +Cc: Geert Uytterhoeven, netdev, linux-m68k, Greg Ungerer
On 07/04/2012 05:52 PM, Geert Uytterhoeven wrote:
> On Wed, Jul 4, 2012 at 8:39 AM, Joe Perches <joe@perches.com> wrote:
>>>>> +static int mcf8390_init(struct net_device *dev)
>>>>> +{
>>>>> + static u32 offsets[] = {
>>>>> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
>>>>> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
>>>>> + };
>>>>
>>>> const? u8?
>>>
>>> That is assigned to the "reg_offset" field of "struct ei_device"
>>> (defined in the existing 8390.h) and that is:
>>>
>>> u32 *reg_offset; /* Register mapping table */
>>>
>>> So I can't change this.
>>
>> Sure you can, you can assign a u8 to a u32 just fine.
>
> It's not the value that's assigned, but a pointer to the table, so
> for now it must be non-const u32 *.
>
>> The value fits in a u8. Might as well make it take
>> less data space. static const makes it read-only and
>> makes the compiler assign it just once instead of at
>> function invocation.
>
> That needs changes to drivers/net/ethernet/8390/8390.h, and
> also probably to some drivers that assign values to the array.
Yes, that is right, some drivers as well.
Just making that local offsets array const generates compiler
warnings (as you would expect):
CC drivers/net/ethernet/8390/mcf8390.o
drivers/net/ethernet/8390/mcf8390.c: In function ‘mcf8390_init’:
drivers/net/ethernet/8390/mcf8390.c:393:23: warning: assignment discards
qualifiers from pointer target type
Regards
Greg
------------------------------------------------------------------------
Greg Ungerer -- Principal Engineer EMAIL: gerg@snapgear.com
SnapGear Group, McAfee PHONE: +61 7 3435 2888
8 Gardner Close, FAX: +61 7 3891 3630
Milton, QLD, 4064, Australia WEB: http://www.SnapGear.com
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
@ 2012-07-04 8:06 ` Greg Ungerer
0 siblings, 0 replies; 14+ messages in thread
From: Greg Ungerer @ 2012-07-04 8:06 UTC (permalink / raw)
To: Joe Perches; +Cc: Geert Uytterhoeven, netdev, linux-m68k, Greg Ungerer
On 07/04/2012 05:52 PM, Geert Uytterhoeven wrote:
> On Wed, Jul 4, 2012 at 8:39 AM, Joe Perches <joe@perches.com> wrote:
>>>>> +static int mcf8390_init(struct net_device *dev)
>>>>> +{
>>>>> + static u32 offsets[] = {
>>>>> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
>>>>> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
>>>>> + };
>>>>
>>>> const? u8?
>>>
>>> That is assigned to the "reg_offset" field of "struct ei_device"
>>> (defined in the existing 8390.h) and that is:
>>>
>>> u32 *reg_offset; /* Register mapping table */
>>>
>>> So I can't change this.
>>
>> Sure you can, you can assign a u8 to a u32 just fine.
>
> It's not the value that's assigned, but a pointer to the table, so
> for now it must be non-const u32 *.
>
>> The value fits in a u8. Might as well make it take
>> less data space. static const makes it read-only and
>> makes the compiler assign it just once instead of at
>> function invocation.
>
> That needs changes to drivers/net/ethernet/8390/8390.h, and
> also probably to some drivers that assign values to the array.
Yes, that is right, some drivers as well.
Just making that local offsets array const generates compiler
warnings (as you would expect):
CC drivers/net/ethernet/8390/mcf8390.o
drivers/net/ethernet/8390/mcf8390.c: In function ‘mcf8390_init’:
drivers/net/ethernet/8390/mcf8390.c:393:23: warning: assignment discards
qualifiers from pointer target type
Regards
Greg
------------------------------------------------------------------------
Greg Ungerer -- Principal Engineer EMAIL: gerg@snapgear.com
SnapGear Group, McAfee PHONE: +61 7 3435 2888
8 Gardner Close, FAX: +61 7 3891 3630
Milton, QLD, 4064, Australia WEB: http://www.SnapGear.com
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards
2012-07-04 7:52 ` Geert Uytterhoeven
2012-07-04 8:06 ` Greg Ungerer
@ 2012-07-04 14:52 ` Joe Perches
1 sibling, 0 replies; 14+ messages in thread
From: Joe Perches @ 2012-07-04 14:52 UTC (permalink / raw)
To: Geert Uytterhoeven; +Cc: Greg Ungerer, netdev, linux-m68k, Greg Ungerer
On Wed, 2012-07-04 at 09:52 +0200, Geert Uytterhoeven wrote:
> On Wed, Jul 4, 2012 at 8:39 AM, Joe Perches <joe@perches.com> wrote:
> >> >> +static int mcf8390_init(struct net_device *dev)
> >> >> +{
> >> >> + static u32 offsets[] = {
> >> >> + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
> >> >> + 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
> >> >> + };
> >> >
> >> > const? u8?
> >>
> >> That is assigned to the "reg_offset" field of "struct ei_device"
> >> (defined in the existing 8390.h) and that is:
> >>
> >> u32 *reg_offset; /* Register mapping table */
> >>
> >> So I can't change this.
> >
> > Sure you can, you can assign a u8 to a u32 just fine.
>
> It's not the value that's assigned, but a pointer to the table, so
> for now it must be non-const u32 *.
Oh, then of course you and Greg are correct.
It looks like the code in ax88796.c may actually
need u32 sizes too.
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2012-07-04 14:52 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-07-04 4:56 [PATCH 0/2] net: support for NS8390 based ethernet on ColdFire CPU boards gerg
2012-07-04 4:56 ` gerg
2012-07-04 4:56 ` [PATCH 1/2] m68knommu: move the badly named mcfne.h to a better mcf8390.h gerg
2012-07-04 4:56 ` gerg
2012-07-04 4:56 ` [PATCH 2/2] net: add support for NS8390 based eth controllers on some ColdFire CPU boards gerg
2012-07-04 4:56 ` gerg
2012-07-04 5:18 ` Joe Perches
2012-07-04 6:18 ` Greg Ungerer
2012-07-04 6:18 ` Greg Ungerer
2012-07-04 6:39 ` Joe Perches
2012-07-04 7:52 ` Geert Uytterhoeven
2012-07-04 8:06 ` Greg Ungerer
2012-07-04 8:06 ` Greg Ungerer
2012-07-04 14:52 ` Joe Perches
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.