From: Tushar Behera <tushar.behera@linaro.org>
To: linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org,
devicetree-discuss@lists.ozlabs.org
Cc: kgene.kim@samsung.com, patches@linaro.org,
Amit Daniel Kachhap <amit.daniel@samsung.com>
Subject: [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry
Date: Thu, 7 Feb 2013 10:45:26 +0530 [thread overview]
Message-ID: <1360214129-4096-2-git-send-email-tushar.behera@linaro.org> (raw)
In-Reply-To: <1360214129-4096-1-git-send-email-tushar.behera@linaro.org>
From: Amit Daniel Kachhap <amit.daniel@samsung.com>
Added S5M8767 PMIC DT nodes to Arndale board.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
arch/arm/boot/dts/exynos5250-arndale.dts | 213 +++++++++++++++++++++++++++++-
1 files changed, 212 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 9ce40df..b40a02f 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -25,7 +25,218 @@
};
i2c@12C60000 {
- status = "disabled";
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ samsung,i2c-slave-addr = <0x66>;
+ gpios = <&gpb3 0 2 3 0>,
+ <&gpb3 1 2 3 0>;
+
+ s5m8767_pmic@66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+
+ s5m8767,pmic-buck2-dvs-voltage = <1300000>;
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>;
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>;
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1 0 0>,
+ <&gpd1 1 1 0 0>,
+ <&gpd1 2 1 0 0>;
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>,
+ <&gpx2 4 1 0 0>,
+ <&gpx2 5 1 0 0>;
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_28IO_DP_1.35V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDD_COMMON1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD_IOPERI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD_MPLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD_XPLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD_COMMON2_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD_33ON_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD_COMMON3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_ABB2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD_USB_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_COMMON4_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDDQ_MMC2_3_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "VDD_33ON_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_MIF_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_INT_1.0V";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VDD_G3D_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDD_MEM_1.35V";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1355000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ };
+ };
};
i2c@12C70000 {
--
1.7.4.1
WARNING: multiple messages have this Message-ID
From: tushar.behera@linaro.org (Tushar Behera)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry
Date: Thu, 7 Feb 2013 10:45:26 +0530 [thread overview]
Message-ID: <1360214129-4096-2-git-send-email-tushar.behera@linaro.org> (raw)
In-Reply-To: <1360214129-4096-1-git-send-email-tushar.behera@linaro.org>
From: Amit Daniel Kachhap <amit.daniel@samsung.com>
Added S5M8767 PMIC DT nodes to Arndale board.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
arch/arm/boot/dts/exynos5250-arndale.dts | 213 +++++++++++++++++++++++++++++-
1 files changed, 212 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 9ce40df..b40a02f 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -25,7 +25,218 @@
};
i2c at 12C60000 {
- status = "disabled";
+ status = "okay";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <20000>;
+ samsung,i2c-slave-addr = <0x66>;
+ gpios = <&gpb3 0 2 3 0>,
+ <&gpb3 1 2 3 0>;
+
+ s5m8767_pmic at 66 {
+ compatible = "samsung,s5m8767-pmic";
+ reg = <0x66>;
+
+ s5m8767,pmic-buck2-dvs-voltage = <1300000>;
+ s5m8767,pmic-buck3-dvs-voltage = <1100000>;
+ s5m8767,pmic-buck4-dvs-voltage = <1200000>;
+ s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1 0 0>,
+ <&gpd1 1 1 0 0>,
+ <&gpd1 2 1 0 0>;
+ s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>,
+ <&gpx2 4 1 0 0>,
+ <&gpx2 5 1 0 0>;
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_28IO_DP_1.35V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VDD_COMMON1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VDD_IOPERI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VDD_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD_MPLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD_XPLL_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VDD_COMMON2_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VDD_33ON_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VDD_COMMON3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD_ABB2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD_USB_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_COMMON4_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VDDQ_MMC2_3_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "VDD_33ON_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_MIF_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VDD_INT_1.0V";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VDD_G3D_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ op_mode = <1>;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VDD_MEM_1.35V";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1355000>;
+ regulator-always-on;
+ regulator-boot-on;
+ op_mode = <1>;
+ };
+
+ };
+ };
};
i2c at 12C70000 {
--
1.7.4.1
next prev parent reply other threads:[~2013-02-07 5:15 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-07 5:15 [PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:15 ` Tushar Behera [this message]
2013-02-07 5:15 ` [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry Tushar Behera
2013-02-07 5:49 ` Kumar, Anil
2013-02-07 5:49 ` Kumar, Anil
2013-02-07 5:56 ` Tushar Behera
2013-02-07 5:56 ` Tushar Behera
2013-02-11 0:38 ` amit daniel kachhap
2013-02-11 0:38 ` amit daniel kachhap
2013-03-11 2:05 ` Kukjin Kim
2013-03-11 2:05 ` Kukjin Kim
2013-02-07 5:15 ` [PATCH 3/5] ARM: dts: exynos5250-arndale: Add vmmc regulator support Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:15 ` [PATCH 4/5] ARM: dts: exynos5250-arndale: Add MFC codec support Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 5:15 ` [PATCH 5/5] ARM: dts: exynos5250-arndale: Add HDMI HPD and regulator node Tushar Behera
2013-02-07 5:15 ` Tushar Behera
2013-02-07 6:17 ` [PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons Kumar, Anil
2013-02-07 6:17 ` Kumar, Anil
2013-02-07 6:26 ` Tushar Behera
2013-02-07 6:26 ` Tushar Behera
2013-02-07 6:36 ` Manish Badarkhe
2013-02-07 6:36 ` Manish Badarkhe
2013-02-07 6:56 ` Tushar Behera
2013-02-07 6:56 ` Tushar Behera
2013-02-07 7:43 ` Girish KS
2013-02-07 7:43 ` Girish KS
2013-02-07 9:40 ` Tushar Behera
2013-02-07 9:40 ` Tushar Behera
2013-02-07 11:25 ` Tomasz Figa
2013-02-07 11:25 ` Tomasz Figa
2013-02-07 10:30 ` Tomasz Figa
2013-02-07 10:30 ` Tomasz Figa
2013-03-11 2:05 ` Kukjin Kim
2013-03-11 2:05 ` Kukjin Kim
2013-03-11 9:44 ` Tushar Behera
2013-03-11 9:44 ` Tushar Behera
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1360214129-4096-2-git-send-email-tushar.behera@linaro.org \
--to=tushar.behera@linaro.org \
--cc=amit.daniel@samsung.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=kgene.kim@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=patches@linaro.org \
--subject='Re: [PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry' \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.