All of lore.kernel.org
 help / color / mirror / Atom feed
From: Matt Porter <mporter@ti.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2 4/4] ti814x_evm: enable CPSW support
Date: Wed, 20 Mar 2013 11:38:14 -0400	[thread overview]
Message-ID: <1363793894-1400-5-git-send-email-mporter@ti.com> (raw)
In-Reply-To: <1363793894-1400-1-git-send-email-mporter@ti.com>

Adds CPSW support to the TI814X EVM configured with
an ET1011C PHY in GMII mode.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
---
v2: no changes
---
 board/ti/ti814x/evm.c        |   72 ++++++++++++++++++++++++++++++++++++++++++
 board/ti/ti814x/evm.h        |    1 +
 board/ti/ti814x/mux.c        |   35 ++++++++++++++++++++
 include/configs/ti814x_evm.h |   21 ++++++++++++
 4 files changed, 129 insertions(+)

diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index 8513220..d6c19f5 100644
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -17,6 +17,7 @@
  */
 
 #include <common.h>
+#include <cpsw.h>
 #include <errno.h>
 #include <spl.h>
 #include <asm/arch/cpu.h>
@@ -39,6 +40,8 @@ static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
 static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
 #endif
 
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
 /* UART Defines */
 #ifdef CONFIG_SPL_BUILD
 #define UART_RESET		(0x1 << 1)
@@ -166,6 +169,9 @@ void s_init(void)
 	/* Set MMC pins */
 	enable_mmc1_pin_mux();
 
+	/* Set Ethernet pins */
+	enable_enet_pin_mux();
+
 	/* Enable UART */
 	uart_enable();
 
@@ -199,3 +205,69 @@ int board_mmc_init(bd_t *bis)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x50,
+		.sliver_reg_ofs	= 0x700,
+		.phy_id		= 1,
+	},
+	{
+		.slave_reg_ofs	= 0x90,
+		.sliver_reg_ofs	= 0x740,
+		.phy_id		= 0,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x100,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0x600,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x28,
+	.hw_stats_reg_ofs	= 0x400,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_1,
+};
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+		printf("<ethaddr> not set. Reading from E-fuse\n");
+		/* try reading mac address from efuse */
+		mac_lo = readl(&cdev->macid0l);
+		mac_hi = readl(&cdev->macid0h);
+		mac_addr[0] = mac_hi & 0xFF;
+		mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+		mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+		mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+		mac_addr[4] = mac_lo & 0xFF;
+		mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+		if (is_valid_ether_addr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+		else
+			printf("Unable to read MAC address. Set <ethaddr>\n");
+	}
+
+	return cpsw_register(&cpsw_data);
+}
diff --git a/board/ti/ti814x/evm.h b/board/ti/ti814x/evm.h
index 40f8710..6aebec6 100644
--- a/board/ti/ti814x/evm.h
+++ b/board/ti/ti814x/evm.h
@@ -3,5 +3,6 @@
 
 void enable_uart0_pin_mux(void);
 void enable_mmc1_pin_mux(void);
+void enable_enet_pin_mux(void);
 
 #endif /* _EVM_H */
diff --git a/board/ti/ti814x/mux.c b/board/ti/ti814x/mux.c
index 137acb4..fd9f364 100644
--- a/board/ti/ti814x/mux.c
+++ b/board/ti/ti814x/mux.c
@@ -40,6 +40,36 @@ static struct module_pin_mux mmc1_pin_mux[] = {
 	{-1},
 };
 
+static struct module_pin_mux enet_pin_mux[] = {
+	{OFFSET(pincntl232), MODE(0x01)},		/* EMAC_RMREFCLK */
+	{OFFSET(pincntl233), PULLUP_EN | MODE(0x01)},	/* MDCLK */
+	{OFFSET(pincntl234), PULLUP_EN | MODE(0x01)},	/* MDIO */
+	{OFFSET(pincntl235), MODE(0x01)},		/* EMAC[0]_MTCLK */
+	{OFFSET(pincntl236), MODE(0x01)},		/* EMAC[0]_MCOL */
+	{OFFSET(pincntl237), MODE(0x01)},		/* EMAC[0]_MCRS */
+	{OFFSET(pincntl238), MODE(0x01)},		/* EMAC[0]_MRXER */
+	{OFFSET(pincntl239), MODE(0x01)},		/* EMAC[0]_MRCLK */
+	{OFFSET(pincntl240), MODE(0x01)},		/* EMAC[0]_MRXD[0] */
+	{OFFSET(pincntl241), MODE(0x01)},		/* EMAC[0]_MRXD[1] */
+	{OFFSET(pincntl242), MODE(0x01)},		/* EMAC[0]_MRXD[2] */
+	{OFFSET(pincntl243), MODE(0x01)},		/* EMAC[0]_MRXD[3] */
+	{OFFSET(pincntl244), MODE(0x01)},		/* EMAC[0]_MRXD[4] */
+	{OFFSET(pincntl245), MODE(0x01)},		/* EMAC[0]_MRXD[5] */
+	{OFFSET(pincntl246), MODE(0x01)},		/* EMAC[0]_MRXD[6] */
+	{OFFSET(pincntl247), MODE(0x01)},		/* EMAC[0]_MRXD[7] */
+	{OFFSET(pincntl248), MODE(0x01)},		/* EMAC[0]_MRXDV */
+	{OFFSET(pincntl249), MODE(0x01)},		/* EMAC[0]_GMTCLK */
+	{OFFSET(pincntl250), MODE(0x01)},		/* EMAC[0]_MTXD[0] */
+	{OFFSET(pincntl251), MODE(0x01)},		/* EMAC[0]_MTXD[1] */
+	{OFFSET(pincntl252), MODE(0x01)},		/* EMAC[0]_MTXD[2] */
+	{OFFSET(pincntl253), MODE(0x01)},		/* EMAC[0]_MTXD[3] */
+	{OFFSET(pincntl254), MODE(0x01)},		/* EMAC[0]_MTXD[4] */
+	{OFFSET(pincntl255), MODE(0x01)},		/* EMAC[0]_MTXD[5] */
+	{OFFSET(pincntl256), MODE(0x01)},		/* EMAC[0]_MTXD[6] */
+	{OFFSET(pincntl257), MODE(0x01)},		/* EMAC[0]_MTXD[7] */
+	{OFFSET(pincntl258), MODE(0x01)},		/* EMAC[0]_MTXEN */
+};
+
 void enable_uart0_pin_mux(void)
 {
 	configure_module_pin_mux(uart0_pin_mux);
@@ -49,3 +79,8 @@ void enable_mmc1_pin_mux(void)
 {
 	configure_module_pin_mux(mmc1_pin_mux);
 }
+
+void enable_enet_pin_mux(void)
+{
+	configure_module_pin_mux(enet_pin_mux);
+}
diff --git a/include/configs/ti814x_evm.h b/include/configs/ti814x_evm.h
index 4cbd789..ce0541a 100644
--- a/include/configs/ti814x_evm.h
+++ b/include/configs/ti814x_evm.h
@@ -217,4 +217,25 @@
 /* Unsupported features */
 #undef CONFIG_USE_IRQ
 
+/* Ethernet */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_DRIVER_TI_CPSW
+#define CONFIG_MII
+#define CONFIG_BOOTP_DEFAULT
+#define CONFIG_BOOTP_DNS
+#define CONFIG_BOOTP_DNS2
+#define CONFIG_BOOTP_SEND_HOSTNAME
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_NET_RETRY_COUNT         10
+#define CONFIG_NET_MULTI
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR			1
+#define CONFIG_PHY_ET1011C
+#define CONFIG_PHY_ET1011C_TX_CLK_FIX
+
 #endif	/* ! __CONFIG_TI814X_EVM_H */
-- 
1.7.9.5

  parent reply	other threads:[~2013-03-20 15:38 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-03-20 15:38 [U-Boot] [PATCH v2 0/4] Enable CPSW on TI814x EVM Matt Porter
2013-03-20 15:38 ` [U-Boot] [PATCH v2 1/4] am33xx: add pll and clock support for TI814x CPSW Matt Porter
2013-03-20 17:24   ` Tom Rini
2013-03-20 15:38 ` [U-Boot] [PATCH v2 2/4] cpsw: add support for TI814x slave_regs differences Matt Porter
2013-03-20 15:38 ` [U-Boot] [PATCH v2 3/4] phy: add support for ET1011C phys Matt Porter
2013-03-20 15:38 ` Matt Porter [this message]
2013-04-15 22:16 ` [U-Boot] [PATCH v2 0/4] Enable CPSW on TI814x EVM Tom Rini

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1363793894-1400-5-git-send-email-mporter@ti.com \
    --to=mporter@ti.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.