From mboxrd@z Thu Jan 1 00:00:00 1970 From: sandeep suresh Date: Mon, 8 Apr 2013 23:09:11 +0800 (SGT) Subject: [ath9k-devel] AR9287 ; 2-wire coexistence expected behavior In-Reply-To: <1365413949.24195.YahooMailNeo@web193502.mail.sg3.yahoo.com> References: <515A0847.7000306@gmail.com> <1365088789.89181.YahooMailNeo@web193504.mail.sg3.yahoo.com> <1365131280.68622.YahooMailNeo@web193506.mail.sg3.yahoo.com> <1365148844.61162.YahooMailNeo@web193503.mail.sg3.yahoo.com> <1365152761.13005.YahooMailNeo@web193505.mail.sg3.yahoo.com> <20830.46610.23754.783231@gargle.gargle.HOWL> <1365175482.75704.YahooMailNeo@web193505.mail.sg3.yahoo.com> <1365346495.79596.YahooMailNeo@web193506.mail.sg3.yahoo.com> <1365398445.32740.YahooMailNeo@web193504.mail.sg3.yahoo.com> <1365413949.24195.YahooMailNeo@web193502.mail.sg3.yahoo.com> Message-ID: <1365433751.96373.YahooMailNeo@web193505.mail.sg3.yahoo.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: ath9k-devel@lists.ath9k.org Hello Mr.Adrian and Mr.Sujith, ????As I understand WLAN_ACTIVE is asserted whenever either WLAN_TX or WLAN_Rx is asserted. Hence the pulse trains that I am observing during BT_ACTIVE?asserted might be those corresponding to WLAN_RX. Hence is it possible to route the status of WLAN_TX and WLAN_RX via two separate GPIO lines for monitoring on oscilloscope rather than a single GPIO line for WLAN_ACTIVE (= WLAN_TX + WLAN_RX)? ? Thanks & regards Sandeep. ________________________________ From: sandeep suresh To: Adrian Chadd Cc: Sujith Manoharan ; ath9k-devel ; "linux-wireless at vger.kernel.org" Sent: Monday, 8 April 2013 3:09 PM Subject: Re: [ath9k-devel] AR9287 ; 2-wire coexistence expected behavior Mr.Adrian, ????Thanks for your mail. In FreeBSD, where can I find the 2-wire/3-wire pin definitions, weight register settings, stomping etc. For AR9287, Should I need to look at AR5416 under /sys/dev/ath/ath_hal? Regards Sandeep. ________________________________ From: Adrian Chadd To: sandeep suresh Cc: Sujith Manoharan ; ath9k-devel ; "linux-wireless at vger.kernel.org" Sent: Monday, 8 April 2013 2:30 PM Subject: Re: [ath9k-devel] AR9287 ; 2-wire coexistence expected behavior Also, I don't know why you're writing both config values out to BTCOEX_MODE and BTCOEX_MODE2. MODE2 has a _totally_ different register layout to AR_BT_COEX_MODE. Please make sure you read the register definitions in the header file(s) before you write values out. :-) Adrian -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.ath9k.org/pipermail/ath9k-devel/attachments/20130408/731004c3/attachment.htm