From: Tom Rini <trini@ti.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 08/10] TI:omap5: Convert to ti_armv7_common.h
Date: Fri, 2 Aug 2013 16:26:13 -0400 [thread overview]
Message-ID: <1375475175-5073-9-git-send-email-trini@ti.com> (raw)
In-Reply-To: <1375475175-5073-1-git-send-email-trini@ti.com>
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Signed-off-by: Tom Rini <trini@ti.com>
---
include/configs/dra7xx_evm.h | 11 +--
include/configs/omap5_common.h | 188 +++++-----------------------------------
include/configs/omap5_uevm.h | 8 +-
3 files changed, 31 insertions(+), 176 deletions(-)
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index 51be73d..58786ff 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -12,21 +12,18 @@
#ifndef __CONFIG_DRA7XX_EVM_H
#define __CONFIG_DRA7XX_EVM_H
-/* High Level Configuration Options */
-#define CONFIG_DRA7XX /* in a TI DRA7XX core */
-#define CONFIG_ENV_IS_NOWHERE /* For now. */
-
-#include <configs/omap5_common.h>
+#define CONFIG_DRA7XX
-#define CONFIG_SYS_PROMPT "DRA752 EVM # "
+#define CONFIG_ENV_IS_NOWHERE /* For now. */
+#define CONSOLEDEV "ttyO0"
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_COM1 UART1_BASE
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_OMAP_ABE_SYSCK
-#define CONSOLEDEV "ttyO0"
+#include <configs/omap5_common.h>
/* CPSW Ethernet */
#define CONFIG_CMD_NET
diff --git a/include/configs/omap5_common.h b/include/configs/omap5_common.h
index 7dd56cf..469a081 100644
--- a/include/configs/omap5_common.h
+++ b/include/configs/omap5_common.h
@@ -14,106 +14,51 @@
#ifndef __CONFIG_OMAP5_COMMON_H
#define __CONFIG_OMAP5_COMMON_H
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP54XX /* which is a 54XX */
-#define CONFIG_OMAP_GPIO
-
-/* Get CPU defs */
-#include <asm/arch/cpu.h>
-#include <asm/arch/omap.h>
-
-/* Display CPU and Board Info */
+#define CONFIG_OMAP54XX
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-
#define CONFIG_MISC_INIT_R
+#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_OF_LIBFDT
-#define CONFIG_CMD_BOOTZ
+#define CONFIG_SYS_CACHELINE_SIZE 64
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
+/* Use General purpose timer 1 */
+#define CONFIG_SYS_TIMERBASE GPT2_BASE
+
+#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+
+/* Defines for SDRAM init */
+#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
+#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
+#endif
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_PALMAS_POWER
+#endif
+
+#include <asm/arch/cpu.h>
+#include <asm/arch/omap.h>
-/*
- * Size of malloc() pool
- * Total Size Environment - 128k
- * Malloc - add 256k
- */
#define CONFIG_ENV_SIZE (128 << 10)
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10))
-/* Vector Base */
-#define CONFIG_SYS_CA9_VECTOR_BASE SRAM_ROM_VECT_BASE
-/*
- * Hardware drivers
- */
+#include <configs/ti_armv7_common.h>
/*
- * serial port - NS16550 compatible
+ * Hardware drivers
*/
-#define V_NS16550_CLK 48000000
-
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-
-/* CPU */
-#define CONFIG_ARCH_CPU_INIT
-
-/* I2C */
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_DRIVER_OMAP34XX_I2C
-#define CONFIG_I2C_MULTI_BUS
-
-/* MMC */
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/* Flash */
-#define CONFIG_SYS_NO_FLASH
-
-/* Cache */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-#define CONFIG_SYS_CACHELINE_SHIFT 6
+#define CONFIG_SYS_NS16550_CLK 48000000
-/* commands to include */
-#include <config_cmd_default.h>
-
-/* Enabled commands */
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-
-/* Disabled commands */
+/* Per-SoC commands */
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
-#undef CONFIG_CMD_IMLS /* List all found images */
/*
* Environment setup
*/
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ENV_VARS_UBOOT_CONFIG
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-
-#define CONFIG_ENV_OVERWRITE
-
#ifndef PARTS_DEFAULT
#define PARTS_DEFAULT
#endif
@@ -178,96 +123,11 @@
"fi; " \
"fi"
-#define CONFIG_AUTO_COMPLETE 1
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_CBSIZE 256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-
-/*
- * memtest setup
- */
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (32 << 20))
-
-/* Default load address */
-#define CONFIG_SYS_LOAD_ADDR 0x80000000
-
-/* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE GPT2_BASE
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ 1000
-
-/*
- * SDRAM Memory Map
- * Even though we use two CS all the memory
- * is mapped to one contiguous block
- */
-#define CONFIG_NR_DRAM_BANKS 1
-
-#define CONFIG_SYS_SDRAM_BASE 0x80000000
-#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
- GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-
-/* Defines for SDRAM init */
-#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
-#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
-#endif
-
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_PALMAS_POWER
-#endif
/* Defines for SPL */
-#define CONFIG_SPL
-#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x40300350
#define CONFIG_SPL_MAX_SIZE 0x19000 /* 100K */
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SPL_DISPLAY_PRINT
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-/*
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 80E7FFC0--0x80E80000 should not be used for any
- * other needs.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80E80000
-
-/*
- * BSS and malloc area 64MB into memory to allow enough
- * space for the kernel at the beginning of memory
- */
-#define CONFIG_SPL_BSS_START_ADDR 0x84000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
-#define CONFIG_SYS_SPL_MALLOC_START 0x84100000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */
-#define CONFIG_SPL_GPIO_SUPPORT
-
#endif /* __CONFIG_OMAP5_COMMON_H */
diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h
index 47568e9..d10c2b5 100644
--- a/include/configs/omap5_uevm.h
+++ b/include/configs/omap5_uevm.h
@@ -17,8 +17,6 @@
"uuid_disk=${uuid_gpt_disk};" \
"name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
-#include <configs/omap5_common.h>
-
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 UART3_BASE
#define CONFIG_BAUDRATE 115200
@@ -42,9 +40,9 @@
#define CONFIG_SYS_I2C_TCA642X_BUS_NUM 4
#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
-#define CONFIG_SYS_PROMPT "OMAP5432 uEVM # "
-
#define CONSOLEDEV "ttyO2"
-
#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296
+
+#include <configs/omap5_common.h>
+
#endif /* __CONFIG_OMAP5_EVM_H */
--
1.7.9.5
next prev parent reply other threads:[~2013-08-02 20:26 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-08-02 20:26 [U-Boot] [PATCH 00/10] Introduce common config file for TI ARMv7 platforms Tom Rini
2013-08-02 20:26 ` [U-Boot] [PATCH 01/10] am33xx: Move V_OSCK/V_SCLK to <asm/arch-am33xx/clocks_am33xx.h> Tom Rini
2013-08-03 4:41 ` Heiko Schocher
2013-08-05 15:17 ` Tom Rini
2013-08-05 15:26 ` Lars Poeschel
2013-08-05 15:40 ` Tom Rini
2013-08-05 15:53 ` Tom Rini
2013-08-02 20:26 ` [U-Boot] [PATCH 02/10] am33xx: CONFIG_DMA_COHERENT defines are unused, remove Tom Rini
2013-08-06 18:25 ` Dan Murphy
2013-08-02 20:26 ` [U-Boot] [PATCH 03/10] am33xx: Stop using PHYS_DRAM_1 define Tom Rini
2013-08-02 20:26 ` [U-Boot] [PATCH 04/10] am335x_evm: Use default baud rate table Tom Rini
2013-08-02 20:26 ` [U-Boot] [PATCH 05/10] arm: spl: For Falcon Mode, set a default machid of ~0 Tom Rini
2013-08-05 3:53 ` Heiko Schocher
2013-08-06 18:28 ` Dan Murphy
2013-08-06 19:10 ` Tom Rini
2013-08-06 20:03 ` Dan Murphy
2013-08-02 20:26 ` [U-Boot] [PATCH 06/10] am335x_evm: Bring in 'boot_fdt' logic from i.MX Tom Rini
2013-08-02 20:26 ` [U-Boot] [PATCH 07/10] TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xx Tom Rini
2013-08-06 18:33 ` Dan Murphy
2013-08-06 19:11 ` Tom Rini
2013-08-02 20:26 ` Tom Rini [this message]
2013-08-06 18:37 ` [U-Boot] [PATCH 08/10] TI:omap5: Convert to ti_armv7_common.h Dan Murphy
2013-08-06 19:13 ` Tom Rini
2013-08-06 19:24 ` Dan Murphy
2013-08-06 18:38 ` Dan Murphy
2013-08-02 20:26 ` [U-Boot] [PATCH 09/10] TI:armv7: Enable CONFIG_CMD_SPI Tom Rini
2013-08-06 18:34 ` Dan Murphy
2013-08-06 18:50 ` Jagan Teki
2013-08-06 18:55 ` Jagan Teki
2013-08-06 19:03 ` Tom Rini
2013-08-06 19:10 ` Jagan Teki
2013-08-02 20:26 ` [U-Boot] [PATCH 10/10] TI:armv7: Enable CONFIG_CMD_GPIO Tom Rini
2013-08-06 18:34 ` Dan Murphy
2013-08-03 4:51 ` [U-Boot] [PATCH 00/10] Introduce common config file for TI ARMv7 platforms Heiko Schocher
2013-08-05 15:39 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1375475175-5073-9-git-send-email-trini@ti.com \
--to=trini@ti.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.