* [U-Boot] [PATCH v4 0/3] ARM: tegra: Add the Tamonten-NG Evaluation carrier boards
@ 2013-11-13 16:27 Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 1/3] ARM: tegra: support SKU b1 of Tegra30 Alban Bedel
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Alban Bedel @ 2013-11-13 16:27 UTC (permalink / raw)
To: u-boot
Hi everyone,
I hope everything requiered is there this time:
* The SKU ID has been changed to SKU_ID_T30MQS_P_A3 as suggested by
Thierry
* A new patch has been added to enable the 5th i2c bus on T30, this is
now needed because:
* The i2c buses have been re-numbered to match the numbering used in
the kernel
* The DTS has been re-worked to better reflect the split between COM
and base board. For the i2c buses the split was done according to
where the pull-ups are. So buses enabled in the COM dts have their
pull-ups on the COM module.
* All the "useless" defines have now been removed.
Alban Bedel (3):
ARM: tegra: support SKU b1 of Tegra30
i2c: tegra: Add the fifth bus on SoC with more than 4 buses
ARM: tegra: Add the Tamonten? NG Evaluation Carrier board
arch/arm/cpu/tegra-common/ap.c | 1 +
arch/arm/include/asm/arch-tegra/tegra.h | 1 +
.../common/pinmux-config-tamonten-ng.h | 385 +++++++++++++++++++++
board/avionic-design/common/tamonten-ng.c | 85 +++++
board/avionic-design/dts/tegra30-tamonten.dtsi | 69 ++++
board/avionic-design/dts/tegra30-tec-ng.dts | 18 +
board/avionic-design/tec-ng/Makefile | 32 ++
boards.cfg | 1 +
drivers/i2c/tegra_i2c.c | 5 +
include/configs/tec-ng.h | 84 +++++
10 files changed, 681 insertions(+)
create mode 100644 board/avionic-design/common/pinmux-config-tamonten-ng.h
create mode 100644 board/avionic-design/common/tamonten-ng.c
create mode 100644 board/avionic-design/dts/tegra30-tamonten.dtsi
create mode 100644 board/avionic-design/dts/tegra30-tec-ng.dts
create mode 100644 board/avionic-design/tec-ng/Makefile
create mode 100644 include/configs/tec-ng.h
--
1.8.4.2
^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v4 1/3] ARM: tegra: support SKU b1 of Tegra30
2013-11-13 16:27 [U-Boot] [PATCH v4 0/3] ARM: tegra: Add the Tamonten-NG Evaluation carrier boards Alban Bedel
@ 2013-11-13 16:27 ` Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 2/3] i2c: tegra: Add the fifth bus on SoC with more than 4 buses Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board Alban Bedel
2 siblings, 0 replies; 8+ messages in thread
From: Alban Bedel @ 2013-11-13 16:27 UTC (permalink / raw)
To: u-boot
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
---
V4: Renamed SKU_ID_TM30MQS_A3 to SKU_ID_TM30MQS_P_A3, according to
Thierry Reding this ID should be better suited as there is another
TM30MQS variant with another SKU.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
arch/arm/cpu/tegra-common/ap.c | 1 +
arch/arm/include/asm/arch-tegra/tegra.h | 1 +
2 files changed, 2 insertions(+)
diff --git a/arch/arm/cpu/tegra-common/ap.c b/arch/arm/cpu/tegra-common/ap.c
index 6fb11cb..60d71a6 100644
--- a/arch/arm/cpu/tegra-common/ap.c
+++ b/arch/arm/cpu/tegra-common/ap.c
@@ -71,6 +71,7 @@ int tegra_get_chip_sku(void)
switch (sku_id) {
case SKU_ID_T33:
case SKU_ID_T30:
+ case SKU_ID_TM30MQS_P_A3:
return TEGRA_SOC_T30;
}
break;
diff --git a/arch/arm/include/asm/arch-tegra/tegra.h b/arch/arm/include/asm/arch-tegra/tegra.h
index 25d1fc4..e99f681 100644
--- a/arch/arm/include/asm/arch-tegra/tegra.h
+++ b/arch/arm/include/asm/arch-tegra/tegra.h
@@ -65,6 +65,7 @@ enum {
SKU_ID_T25E = 0x1c,
SKU_ID_T33 = 0x80,
SKU_ID_T30 = 0x81, /* Cardhu value */
+ SKU_ID_TM30MQS_P_A3 = 0xb1,
SKU_ID_T114_ENG = 0x00, /* Dalmore value, unfused */
SKU_ID_T114_1 = 0x01,
};
--
1.8.4.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v4 2/3] i2c: tegra: Add the fifth bus on SoC with more than 4 buses
2013-11-13 16:27 [U-Boot] [PATCH v4 0/3] ARM: tegra: Add the Tamonten-NG Evaluation carrier boards Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 1/3] ARM: tegra: support SKU b1 of Tegra30 Alban Bedel
@ 2013-11-13 16:27 ` Alban Bedel
2013-11-14 5:27 ` Heiko Schocher
2013-11-13 16:27 ` [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board Alban Bedel
2 siblings, 1 reply; 8+ messages in thread
From: Alban Bedel @ 2013-11-13 16:27 UTC (permalink / raw)
To: u-boot
Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
drivers/i2c/tegra_i2c.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/i2c/tegra_i2c.c b/drivers/i2c/tegra_i2c.c
index 9847cf1..594e5dd 100644
--- a/drivers/i2c/tegra_i2c.c
+++ b/drivers/i2c/tegra_i2c.c
@@ -629,3 +629,8 @@ U_BOOT_I2C_ADAP_COMPLETE(tegra2, tegra_i2c_init, tegra_i2c_probe,
U_BOOT_I2C_ADAP_COMPLETE(tegra3, tegra_i2c_init, tegra_i2c_probe,
tegra_i2c_read, tegra_i2c_write,
tegra_i2c_set_bus_speed, 100000, 0, 3)
+#if TEGRA_I2C_NUM_CONTROLLERS > 4
+U_BOOT_I2C_ADAP_COMPLETE(tegra4, tegra_i2c_init, tegra_i2c_probe,
+ tegra_i2c_read, tegra_i2c_write,
+ tegra_i2c_set_bus_speed, 100000, 0, 4)
+#endif
--
1.8.4.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board
2013-11-13 16:27 [U-Boot] [PATCH v4 0/3] ARM: tegra: Add the Tamonten-NG Evaluation carrier boards Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 1/3] ARM: tegra: support SKU b1 of Tegra30 Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 2/3] i2c: tegra: Add the fifth bus on SoC with more than 4 buses Alban Bedel
@ 2013-11-13 16:27 ` Alban Bedel
2013-11-13 17:37 ` Stephen Warren
2013-11-14 9:58 ` [U-Boot] [PATCH v5] " Alban Bedel
2 siblings, 2 replies; 8+ messages in thread
From: Alban Bedel @ 2013-11-13 16:27 UTC (permalink / raw)
To: u-boot
Add support for the new Tamonten? NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
V3: * Removed the retries from pmu_write()
* Removed the not strictly needed power init
V4: * Removed the unused PMU defines
* Removed the useless #ifdef
* Reworked the DTS to enable the device at the proper level
* Re-numbered the i2c bus to match the kernel numbering
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
.../common/pinmux-config-tamonten-ng.h | 385 +++++++++++++++++++++
board/avionic-design/common/tamonten-ng.c | 85 +++++
board/avionic-design/dts/tegra30-tamonten.dtsi | 69 ++++
board/avionic-design/dts/tegra30-tec-ng.dts | 18 +
board/avionic-design/tec-ng/Makefile | 32 ++
boards.cfg | 1 +
include/configs/tec-ng.h | 84 +++++
7 files changed, 674 insertions(+)
create mode 100644 board/avionic-design/common/pinmux-config-tamonten-ng.h
create mode 100644 board/avionic-design/common/tamonten-ng.c
create mode 100644 board/avionic-design/dts/tegra30-tamonten.dtsi
create mode 100644 board/avionic-design/dts/tegra30-tec-ng.dts
create mode 100644 board/avionic-design/tec-ng/Makefile
create mode 100644 include/configs/tec-ng.h
diff --git a/board/avionic-design/common/pinmux-config-tamonten-ng.h b/board/avionic-design/common/pinmux-config-tamonten-ng.h
new file mode 100644
index 0000000..39df731
--- /dev/null
+++ b/board/avionic-design/common/pinmux-config-tamonten-ng.h
@@ -0,0 +1,385 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _PINMUX_CONFIG_TAMONTEN_NG_H_
+#define _PINMUX_CONFIG_TAMONTEN_NG_H_
+
+#define DEFAULT_PINMUX(_pingroup, _mux, _pull, _tri, _io) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_DEFAULT, \
+ .od = PMUX_PIN_OD_DEFAULT, \
+ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \
+ }
+
+#define I2C_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _od) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_##_lock, \
+ .od = PMUX_PIN_OD_##_od, \
+ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \
+ }
+
+#define LV_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _ioreset) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_##_lock, \
+ .od = PMUX_PIN_OD_DEFAULT, \
+ .ioreset = PMUX_PIN_IO_RESET_##_ioreset \
+ }
+
+#define DEFAULT_PADCFG(_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \
+ { \
+ .padgrp = PDRIVE_PINGROUP_##_padgrp, \
+ .slwf = _slwf, \
+ .slwr = _slwr, \
+ .drvup = _drvup, \
+ .drvdn = _drvdn, \
+ .lpmd = PGRP_LPMD_##_lpmd, \
+ .schmt = PGRP_SCHMT_##_schmt, \
+ .hsm = PGRP_HSM_##_hsm, \
+ }
+
+static struct pingroup_config tamonten_ng_pinmux_common[] = {
+ /* SDMMC1 pinmux */
+ DEFAULT_PINMUX(SDMMC1_CLK, SDMMC1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_CMD, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT0, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT1, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT2, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT3, SDMMC1, UP, NORMAL, INPUT),
+
+ /* SDMMC3 pinmux */
+ DEFAULT_PINMUX(SDMMC3_CLK, SDMMC3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_CMD, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT0, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT1, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT2, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT3, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT4, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT5, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT6, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT7, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_IORDY, RSVD1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_CS6_N, RSVD1, UP, NORMAL, INPUT),
+
+ /* SDMMC4 pinmux */
+ LV_PINMUX(SDMMC4_CLK, SDMMC4, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_CMD, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT0, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT1, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT2, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT3, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT4, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT5, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT6, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT7, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_RST_N, RSVD1, DOWN, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* I2C1 pinmux */
+ I2C_PINMUX(GEN1_I2C_SCL, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(GEN1_I2C_SDA, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C2 pinmux */
+ I2C_PINMUX(GEN2_I2C_SCL, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(GEN2_I2C_SDA, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C3 pinmux */
+ I2C_PINMUX(CAM_I2C_SCL, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(CAM_I2C_SDA, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C4 pinmux */
+ I2C_PINMUX(DDC_SCL, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(DDC_SDA, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* Power I2C pinmux */
+ I2C_PINMUX(PWR_I2C_SCL, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(PWR_I2C_SDA, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* UART1 */
+ DEFAULT_PINMUX(ULPI_DATA0, UARTA, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(ULPI_DATA1, UARTA, NORMAL, NORMAL, INPUT),
+
+ /* UART2 */
+ DEFAULT_PINMUX(UART2_RXD, UARTB, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART2_TXD, UARTB, NORMAL, NORMAL, OUTPUT),
+
+ /* UART3 */
+ DEFAULT_PINMUX(UART3_TXD, UARTC, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(UART3_RXD, UARTC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART3_CTS_N, UARTC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART3_RTS_N, UARTC, NORMAL, NORMAL, OUTPUT),
+
+ /* UART4 */
+ DEFAULT_PINMUX(ULPI_CLK, UARTD, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(ULPI_DIR, UARTD, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_NXT, UARTD, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_STP, UARTD, NORMAL, NORMAL, OUTPUT),
+
+ /* DAP */
+ DEFAULT_PINMUX(CLK1_OUT, EXTPERIPH1, NORMAL, NORMAL, INPUT),
+
+ /* I2S1 */
+ DEFAULT_PINMUX(DAP2_FS, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_DIN, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_DOUT, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_SCLK, I2S1, NORMAL, NORMAL, INPUT),
+
+ /* SPDIF */
+ DEFAULT_PINMUX(SPDIF_IN, SPDIF, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPDIF_OUT, SPDIF, NORMAL, NORMAL, OUTPUT),
+
+ /* I2S2 */
+ DEFAULT_PINMUX(DAP3_FS, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_DIN, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_DOUT, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_SCLK, I2S2, NORMAL, NORMAL, INPUT),
+
+ /* DAP4 */
+ DEFAULT_PINMUX(DAP4_FS, I2S3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP4_DIN, I2S3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP4_SCLK, I2S3, NORMAL, NORMAL, INPUT),
+
+ /* Tamonten GPIO */
+ DEFAULT_PINMUX(GPIO_PV2, RSVD1, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GPIO_PV3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI2_CS1_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* LCD */
+ DEFAULT_PINMUX(LCD_PWR1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PWR2, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SDIN, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SDOUT, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_WR_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_CS0_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DC0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SCK, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PWR0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PCLK, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DE, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_HSYNC, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_VSYNC, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D2, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D3, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D4, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D5, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D6, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D7, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D8, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D9, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D10, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D11, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D12, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D13, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D14, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D15, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D16, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D17, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D18, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D19, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D20, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D21, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D22, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D23, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_CS1_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_M1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DC1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CRT_HSYNC, CRT, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(CRT_VSYNC, CRT, NORMAL, NORMAL, OUTPUT),
+
+ /* BT656 */
+ LV_PINMUX(VI_MCLK, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_PCLK, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_HSYNC, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_VSYNC, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D2, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D3, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D4, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D5, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D6, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D7, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D8, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D9, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D11, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* GPIOs */
+ DEFAULT_PINMUX(GPIO_PU5, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU6, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_AD12, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* LCD BL */
+ DEFAULT_PINMUX(GMI_AD8, PWM0, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD10, RSVD4, NORMAL, NORMAL, OUTPUT),
+
+ /* SPI4 */
+ DEFAULT_PINMUX(GMI_A16, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A17, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A18, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A19, SPI4, NORMAL, NORMAL, INPUT),
+
+ /* Video input GPIO */
+ DEFAULT_PINMUX(GPIO_PCC1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB0, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB7, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Sensor GPIO */
+ DEFAULT_PINMUX(GPIO_PCC2, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* JTAG */
+ DEFAULT_PINMUX(JTAG_RTCK, RTCK, NORMAL, NORMAL, OUTPUT),
+
+ /* Power controls */
+ DEFAULT_PINMUX(GMI_CS2_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* SPI1 */
+ DEFAULT_PINMUX(SPI1_MOSI, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_SCK, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_CS0_N, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_MISO, SPI1, NORMAL, NORMAL, INPUT),
+
+ /* PMU */
+ DEFAULT_PINMUX(GPIO_PV0, RSVD1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SYS_CLK_REQ, SYSCLK, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(CLK_32K_IN, SYSCLK, NORMAL, NORMAL, INPUT),
+
+ /* PCI */
+ DEFAULT_PINMUX(PEX_L0_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L0_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L0_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_WAKE_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L1_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L1_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L1_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L2_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L2_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L2_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+
+ /* HDMI */
+ DEFAULT_PINMUX(HDMI_CEC, CEC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(HDMI_INT, RSVD1, NORMAL, TRISTATE, INPUT),
+};
+
+static struct pingroup_config unused_pins_lowpower[] = {
+ /* UART1 - NC */
+ DEFAULT_PINMUX(ULPI_DATA2, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA3, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA4, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA5, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA6, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA7, UARTA, NORMAL, NORMAL, INPUT),
+
+ /* UART2 - NC */
+ DEFAULT_PINMUX(UART2_RTS_N, UARTB, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART2_CTS_N, UARTB, NORMAL, NORMAL, INPUT),
+
+ /* DAP - NC */
+ DEFAULT_PINMUX(CLK1_REQ, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK3_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK3_REQ, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* DAP4 - NC */
+ DEFAULT_PINMUX(DAP4_DOUT, I2S3, NORMAL, NORMAL, INPUT),
+
+ /* Tamonten GPIO - NC */
+ DEFAULT_PINMUX(CLK2_OUT, EXTPERIPH2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK2_REQ, DAP, NORMAL, NORMAL, INPUT),
+
+ /* BT656 - NC */
+ LV_PINMUX(VI_D0, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D1, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D10, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* GPIO - NC */
+ DEFAULT_PINMUX(GPIO_PU0, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU2, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU4, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Video input - NC */
+ DEFAULT_PINMUX(CAM_MCLK, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB5, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB6, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW11, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* KBC keys - NC */
+ DEFAULT_PINMUX(KB_ROW0, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW1, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW2, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW3, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW4, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW5, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW6, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW7, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW8, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW9, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW10, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW12, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW13, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW14, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW15, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL0, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL1, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL2, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL3, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL4, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL5, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL6, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL7, KBC, UP, NORMAL, INPUT),
+
+ /* PMU - NC */
+ DEFAULT_PINMUX(CLK_32K_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Power rails GPIO - NC */
+ DEFAULT_PINMUX(SPI2_SCK, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB4, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Others - NC */
+ DEFAULT_PINMUX(GMI_WP_N, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PV1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_WAIT, NAND, UP, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_ADV_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_CLK, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_CS3_N, NAND, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_CS7_N, NAND, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_AD0, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD1, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD2, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD3, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD4, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD5, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD6, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD7, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD9, PWM1, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD11, NAND, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD13, NAND, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_WR_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_OE_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_DQS, NAND, NORMAL, TRISTATE, OUTPUT),
+};
+
+static struct padctrl_config tamonten_ng_padctrl[] = {
+ /* (_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) */
+ DEFAULT_PADCFG(SDIO1, SDIOCFG_DRVUP_SLWF, SDIOCFG_DRVDN_SLWR,
+ SDIOCFG_DRVUP, SDIOCFG_DRVDN, NONE, DISABLE, DISABLE),
+};
+#endif /* _PINMUX_CONFIG_TAMONTEN_NG_H_ */
diff --git a/board/avionic-design/common/tamonten-ng.c b/board/avionic-design/common/tamonten-ng.c
new file mode 100644
index 0000000..9d395c6
--- /dev/null
+++ b/board/avionic-design/common/tamonten-ng.c
@@ -0,0 +1,85 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/gp_padctrl.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include "pinmux-config-tamonten-ng.h"
+#include <i2c.h>
+
+#define PMU_I2C_ADDRESS 0x2D
+
+#define PMU_REG_LDO5 0x32
+
+#define PMU_REG_LDO_HIGH_POWER 1
+
+/* Voltage selection for the LDOs with 100mV resolution */
+#define PMU_REG_LDO_SEL_100(mV) ((((mV - 1000) / 100) + 2) << 2)
+
+#define PMU_REG_LDO_100(st, mV) (PMU_REG_LDO_##st | PMU_REG_LDO_SEL_100(mV))
+
+#define PMU_LDO5(st, mV) PMU_REG_LDO_100(st, mV)
+
+void pinmux_init(void)
+{
+ pinmux_config_table(tamonten_ng_pinmux_common,
+ ARRAY_SIZE(tamonten_ng_pinmux_common));
+ pinmux_config_table(unused_pins_lowpower,
+ ARRAY_SIZE(unused_pins_lowpower));
+
+ /* Initialize any non-default pad configs (APB_MISC_GP regs) */
+ padgrp_config_table(tamonten_ng_padctrl,
+ ARRAY_SIZE(tamonten_ng_padctrl));
+}
+
+void gpio_early_init(void)
+{
+ /* Turn on the alive signal */
+ gpio_request(GPIO_PV2, "ALIVE");
+ gpio_direction_output(GPIO_PV2, 1);
+
+ /* Remove the reset on the external periph */
+ gpio_request(GPIO_PI4, "nRST_PERIPH");
+ gpio_direction_output(GPIO_PI4, 1);
+}
+
+void pmu_write(uchar reg, uchar data)
+{
+ i2c_set_bus_num(4); /* PMU is on bus 4 */
+ i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1);
+}
+
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+ /* Enable LDO5 with 3.3v for SDMMC3 */
+ pmu_write(PMU_REG_LDO5, PMU_LDO5(HIGH_POWER, 3300));
+
+ /* Switch the power on */
+ gpio_request(GPIO_PJ2, "EN_3V3_EMMC");
+ gpio_direction_output(GPIO_PJ2, 1);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+ /*
+ * NOTE: We don't do mmc-specific pin muxes here.
+ * They were done globally in pinmux_init().
+ */
+
+ /* Bring up the SDIO1 power rail */
+ board_sdmmc_voltage_init();
+}
diff --git a/board/avionic-design/dts/tegra30-tamonten.dtsi b/board/avionic-design/dts/tegra30-tamonten.dtsi
new file mode 100644
index 0000000..50d5762
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tamonten.dtsi
@@ -0,0 +1,69 @@
+#include "tegra30.dtsi"
+
+/ {
+ model = "Avionic Design Tamonten NG";
+ compatible = "ad,tamonten-ng", "nvidia,tegra30";
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ aliases {
+ i2c0 = "/i2c at 7000c000";
+ i2c1 = "/i2c at 7000c700";
+ i2c2 = "/i2c at 7000c400";
+ i2c3 = "/i2c at 7000c500";
+ i2c4 = "/i2c at 7000d000";
+ sdhci0 = "/sdhci at 78000600";
+ sdhci1 = "/sdhci at 78000400";
+ sdhci2 = "/sdhci at 78000000";
+ usb0 = "/usb at 7d008000";
+ };
+
+ /* GEN1 */
+ i2c at 7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* GEN2 */
+ i2c at 7000c400 {
+ clock-frequency = <100000>;
+ };
+
+ /* CAM */
+ i2c at 7000c500 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* DDC */
+ i2c at 7000c700 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* PWR */
+ i2c at 7000d000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* SD slot on the base board */
+ sdhci at 78000400 {
+ cd-gpios = <&gpio 69 1>; /* gpio PI5 */
+ wp-gpios = <&gpio 67 0>; /* gpio PI3 */
+ bus-width = <4>;
+ };
+
+ /* EMMC on the COM module */
+ sdhci at 78000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ usb at 7d008000 {
+ status = "okay";
+ };
+
+};
diff --git a/board/avionic-design/dts/tegra30-tec-ng.dts b/board/avionic-design/dts/tegra30-tec-ng.dts
new file mode 100644
index 0000000..8a69e81
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tec-ng.dts
@@ -0,0 +1,18 @@
+/dts-v1/;
+
+#include "tegra30-tamonten.dtsi"
+
+/ {
+ model = "Avionic Design Tamonten? NG Evaluation Carrier";
+ compatible = "ad,tec-ng", "nvidia,tegra30";
+
+ /* GEN2 */
+ i2c at 7000c400 {
+ status = "okay";
+ };
+
+ /* SD card slot */
+ sdhci at 78000400 {
+ status = "okay";
+ };
+};
diff --git a/board/avionic-design/tec-ng/Makefile b/board/avionic-design/tec-ng/Makefile
new file mode 100644
index 0000000..22e19e0
--- /dev/null
+++ b/board/avionic-design/tec-ng/Makefile
@@ -0,0 +1,32 @@
+#
+# (C) Copyright 2013
+# Avionic Design GmbH <www.avionic-design.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common)
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS-y := ../common/tamonten-ng.o
+
+include ../../nvidia/common/common.mk
+
+COBJS := $(COBJS-y)
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/boards.cfg b/boards.cfg
index caba64e..fc5cb2d 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -353,6 +353,7 @@ Active arm armv7:arm720t tegra114 nvidia dalmore
Active arm armv7:arm720t tegra20 avionic-design medcom-wide medcom-wide - Thierry Reding <thierry.reding@avionic-design.de>
Active arm armv7:arm720t tegra20 avionic-design plutux plutux - Thierry Reding <thierry.reding@avionic-design.de>
Active arm armv7:arm720t tegra20 avionic-design tec tec - Thierry Reding <thierry.reding@avionic-design.de>
+Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel <alban.bedel@avionic-design.de>
Active arm armv7:arm720t tegra20 compal paz00 paz00 - Tom Warren <twarren@nvidia.com>:Stephen Warren <swarren@nvidia.com>
Active arm armv7:arm720t tegra20 compulab trimslice trimslice - Tom Warren <twarren@nvidia.com>:Stephen Warren <swarren@nvidia.com>
Active arm armv7:arm720t tegra20 nvidia harmony harmony - Tom Warren <twarren@nvidia.com>
diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
new file mode 100644
index 0000000..13baa76
--- /dev/null
+++ b/include/configs/tec-ng.h
@@ -0,0 +1,84 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "tegra30-common.h"
+
+/* Enable fdt support for tec-ng. Flash the image in u-boot-dtb.bin */
+#define CONFIG_DEFAULT_DEVICE_TREE tegra30-tec-ng
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* High-level configuration options */
+#define V_PROMPT "Tegra30 (TEC-NG) # "
+#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten? NG Evaluation Carrier"
+
+/* Board-specific serial config */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_TEGRA_ENABLE_UARTD
+#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* I2C */
+#define CONFIG_SYS_I2C_TEGRA
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_TEGRA_MMC
+#define CONFIG_CMD_MMC
+
+/* Environment in eMMC, at the end of 2nd "boot sector" */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 2
+
+/* SPI */
+#define CONFIG_TEGRA20_SLINK
+#define CONFIG_TEGRA_SLINK_CTRLS 6
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_SIZE (4 << 20)
+
+/* USB Host support */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_TEGRA
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB
+
+/* USB networking support */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/* General networking support */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+
+/* Tag support */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+/* support the new (FDT-based) image format */
+#define CONFIG_FIT
+
+#include "tegra-common-post.h"
+
+#endif /* __CONFIG_H */
--
1.8.4.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board
2013-11-13 16:27 ` [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board Alban Bedel
@ 2013-11-13 17:37 ` Stephen Warren
2013-11-14 9:58 ` [U-Boot] [PATCH v5] " Alban Bedel
1 sibling, 0 replies; 8+ messages in thread
From: Stephen Warren @ 2013-11-13 17:37 UTC (permalink / raw)
To: u-boot
On 11/13/2013 09:27 AM, Alban Bedel wrote:
> Add support for the new Tamonten? NG platform from Avionic Design.
> Currently only I2C, MMC, USB and ethernet have been tested.
>
> Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
> ---
> V3: * Removed the retries from pmu_write()
> * Removed the not strictly needed power init
> V4: * Removed the unused PMU defines
> * Removed the useless #ifdef
> * Reworked the DTS to enable the device at the proper level
> * Re-numbered the i2c bus to match the kernel numbering
Note that the kernel doesn't have a defined I2C bus numbering; any
numbering that exists is a side-effect of the non-guaranteed I2C node
enumeration order. That said, feel free to make the bus ordering in
U-Boot be whatever you want.
> diff --git a/board/avionic-design/tec-ng/Makefile b/board/avionic-design/tec-ng/Makefile
I believe there's been a recent cleanup pass on all the Makefiles, so a
lot of this boiler-plate needs to be removed to conform with the new
style. Take a look at board/nvidia/*/Makefile for some examples.
Aside from that, the series briefly,
Reviewed-by: Stephen Warren <swarren@nvidia.com>
^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v4 2/3] i2c: tegra: Add the fifth bus on SoC with more than 4 buses
2013-11-13 16:27 ` [U-Boot] [PATCH v4 2/3] i2c: tegra: Add the fifth bus on SoC with more than 4 buses Alban Bedel
@ 2013-11-14 5:27 ` Heiko Schocher
0 siblings, 0 replies; 8+ messages in thread
From: Heiko Schocher @ 2013-11-14 5:27 UTC (permalink / raw)
To: u-boot
Hello Alban,
Am 13.11.2013 17:27, schrieb Alban Bedel:
> Create the i2c adapter object for the fifth bus on SoC with more than
> 4 buses. This allow using all the bus available on T30.
>
> Signed-off-by: Alban Bedel<alban.bedel@avionic-design.de>
> ---
> drivers/i2c/tegra_i2c.c | 5 +++++
> 1 file changed, 5 insertions(+)
Acked-by: Heiko Schocher <hs@denx.de>
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v5] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board
2013-11-13 16:27 ` [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board Alban Bedel
2013-11-13 17:37 ` Stephen Warren
@ 2013-11-14 9:58 ` Alban Bedel
2013-11-14 22:45 ` Stephen Warren
1 sibling, 1 reply; 8+ messages in thread
From: Alban Bedel @ 2013-11-14 9:58 UTC (permalink / raw)
To: u-boot
Add support for the new Tamonten? NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
---
V3: * Removed the retries from pmu_write()
* Removed the not strictly needed power init
V4: * Removed the unused PMU defines
* Removed the useless #ifdef
* Reworked the DTS to enable the device at the proper level
* Re-numbered the i2c bus to match the numbering we use in kernel
V5: * Updated the board Makefile to use the new style
---
.../common/pinmux-config-tamonten-ng.h | 385 +++++++++++++++++++++
board/avionic-design/common/tamonten-ng.c | 85 +++++
board/avionic-design/dts/tegra30-tamonten.dtsi | 69 ++++
board/avionic-design/dts/tegra30-tec-ng.dts | 18 +
board/avionic-design/tec-ng/Makefile | 12 +
boards.cfg | 1 +
include/configs/tec-ng.h | 84 +++++
7 files changed, 654 insertions(+)
create mode 100644 board/avionic-design/common/pinmux-config-tamonten-ng.h
create mode 100644 board/avionic-design/common/tamonten-ng.c
create mode 100644 board/avionic-design/dts/tegra30-tamonten.dtsi
create mode 100644 board/avionic-design/dts/tegra30-tec-ng.dts
create mode 100644 board/avionic-design/tec-ng/Makefile
create mode 100644 include/configs/tec-ng.h
diff --git a/board/avionic-design/common/pinmux-config-tamonten-ng.h b/board/avionic-design/common/pinmux-config-tamonten-ng.h
new file mode 100644
index 0000000..39df731
--- /dev/null
+++ b/board/avionic-design/common/pinmux-config-tamonten-ng.h
@@ -0,0 +1,385 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _PINMUX_CONFIG_TAMONTEN_NG_H_
+#define _PINMUX_CONFIG_TAMONTEN_NG_H_
+
+#define DEFAULT_PINMUX(_pingroup, _mux, _pull, _tri, _io) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_DEFAULT, \
+ .od = PMUX_PIN_OD_DEFAULT, \
+ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \
+ }
+
+#define I2C_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _od) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_##_lock, \
+ .od = PMUX_PIN_OD_##_od, \
+ .ioreset = PMUX_PIN_IO_RESET_DEFAULT, \
+ }
+
+#define LV_PINMUX(_pingroup, _mux, _pull, _tri, _io, _lock, _ioreset) \
+ { \
+ .pingroup = PINGRP_##_pingroup, \
+ .func = PMUX_FUNC_##_mux, \
+ .pull = PMUX_PULL_##_pull, \
+ .tristate = PMUX_TRI_##_tri, \
+ .io = PMUX_PIN_##_io, \
+ .lock = PMUX_PIN_LOCK_##_lock, \
+ .od = PMUX_PIN_OD_DEFAULT, \
+ .ioreset = PMUX_PIN_IO_RESET_##_ioreset \
+ }
+
+#define DEFAULT_PADCFG(_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) \
+ { \
+ .padgrp = PDRIVE_PINGROUP_##_padgrp, \
+ .slwf = _slwf, \
+ .slwr = _slwr, \
+ .drvup = _drvup, \
+ .drvdn = _drvdn, \
+ .lpmd = PGRP_LPMD_##_lpmd, \
+ .schmt = PGRP_SCHMT_##_schmt, \
+ .hsm = PGRP_HSM_##_hsm, \
+ }
+
+static struct pingroup_config tamonten_ng_pinmux_common[] = {
+ /* SDMMC1 pinmux */
+ DEFAULT_PINMUX(SDMMC1_CLK, SDMMC1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_CMD, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT0, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT1, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT2, SDMMC1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC1_DAT3, SDMMC1, UP, NORMAL, INPUT),
+
+ /* SDMMC3 pinmux */
+ DEFAULT_PINMUX(SDMMC3_CLK, SDMMC3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_CMD, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT0, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT1, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT2, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT3, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT4, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT5, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT6, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SDMMC3_DAT7, SDMMC3, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_IORDY, RSVD1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_CS6_N, RSVD1, UP, NORMAL, INPUT),
+
+ /* SDMMC4 pinmux */
+ LV_PINMUX(SDMMC4_CLK, SDMMC4, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_CMD, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT0, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT1, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT2, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT3, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT4, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT5, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT6, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_DAT7, SDMMC4, UP, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(SDMMC4_RST_N, RSVD1, DOWN, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* I2C1 pinmux */
+ I2C_PINMUX(GEN1_I2C_SCL, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(GEN1_I2C_SDA, I2C1, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C2 pinmux */
+ I2C_PINMUX(GEN2_I2C_SCL, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(GEN2_I2C_SDA, I2C2, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C3 pinmux */
+ I2C_PINMUX(CAM_I2C_SCL, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(CAM_I2C_SDA, I2C3, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* I2C4 pinmux */
+ I2C_PINMUX(DDC_SCL, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(DDC_SDA, I2C4, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* Power I2C pinmux */
+ I2C_PINMUX(PWR_I2C_SCL, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+ I2C_PINMUX(PWR_I2C_SDA, I2CPWR, NORMAL, NORMAL, INPUT, DISABLE, ENABLE),
+
+ /* UART1 */
+ DEFAULT_PINMUX(ULPI_DATA0, UARTA, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(ULPI_DATA1, UARTA, NORMAL, NORMAL, INPUT),
+
+ /* UART2 */
+ DEFAULT_PINMUX(UART2_RXD, UARTB, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART2_TXD, UARTB, NORMAL, NORMAL, OUTPUT),
+
+ /* UART3 */
+ DEFAULT_PINMUX(UART3_TXD, UARTC, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(UART3_RXD, UARTC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART3_CTS_N, UARTC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART3_RTS_N, UARTC, NORMAL, NORMAL, OUTPUT),
+
+ /* UART4 */
+ DEFAULT_PINMUX(ULPI_CLK, UARTD, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(ULPI_DIR, UARTD, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_NXT, UARTD, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_STP, UARTD, NORMAL, NORMAL, OUTPUT),
+
+ /* DAP */
+ DEFAULT_PINMUX(CLK1_OUT, EXTPERIPH1, NORMAL, NORMAL, INPUT),
+
+ /* I2S1 */
+ DEFAULT_PINMUX(DAP2_FS, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_DIN, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_DOUT, I2S1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP2_SCLK, I2S1, NORMAL, NORMAL, INPUT),
+
+ /* SPDIF */
+ DEFAULT_PINMUX(SPDIF_IN, SPDIF, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPDIF_OUT, SPDIF, NORMAL, NORMAL, OUTPUT),
+
+ /* I2S2 */
+ DEFAULT_PINMUX(DAP3_FS, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_DIN, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_DOUT, I2S2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP3_SCLK, I2S2, NORMAL, NORMAL, INPUT),
+
+ /* DAP4 */
+ DEFAULT_PINMUX(DAP4_FS, I2S3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP4_DIN, I2S3, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(DAP4_SCLK, I2S3, NORMAL, NORMAL, INPUT),
+
+ /* Tamonten GPIO */
+ DEFAULT_PINMUX(GPIO_PV2, RSVD1, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GPIO_PV3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI2_CS1_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* LCD */
+ DEFAULT_PINMUX(LCD_PWR1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PWR2, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SDIN, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SDOUT, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_WR_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_CS0_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DC0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_SCK, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PWR0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_PCLK, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DE, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_HSYNC, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_VSYNC, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D0, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D2, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D3, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D4, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D5, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D6, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D7, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D8, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D9, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D10, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D11, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D12, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D13, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D14, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D15, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D16, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D17, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D18, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D19, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D20, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D21, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D22, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_D23, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_CS1_N, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_M1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(LCD_DC1, DISPA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CRT_HSYNC, CRT, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(CRT_VSYNC, CRT, NORMAL, NORMAL, OUTPUT),
+
+ /* BT656 */
+ LV_PINMUX(VI_MCLK, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_PCLK, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_HSYNC, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_VSYNC, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D2, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D3, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D4, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D5, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D6, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D7, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D8, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D9, VI, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D11, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* GPIOs */
+ DEFAULT_PINMUX(GPIO_PU5, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU6, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_AD12, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* LCD BL */
+ DEFAULT_PINMUX(GMI_AD8, PWM0, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD10, RSVD4, NORMAL, NORMAL, OUTPUT),
+
+ /* SPI4 */
+ DEFAULT_PINMUX(GMI_A16, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A17, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A18, SPI4, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_A19, SPI4, NORMAL, NORMAL, INPUT),
+
+ /* Video input GPIO */
+ DEFAULT_PINMUX(GPIO_PCC1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB0, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB7, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Sensor GPIO */
+ DEFAULT_PINMUX(GPIO_PCC2, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* JTAG */
+ DEFAULT_PINMUX(JTAG_RTCK, RTCK, NORMAL, NORMAL, OUTPUT),
+
+ /* Power controls */
+ DEFAULT_PINMUX(GMI_CS2_N, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* SPI1 */
+ DEFAULT_PINMUX(SPI1_MOSI, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_SCK, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_CS0_N, SPI1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(SPI1_MISO, SPI1, NORMAL, NORMAL, INPUT),
+
+ /* PMU */
+ DEFAULT_PINMUX(GPIO_PV0, RSVD1, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(SYS_CLK_REQ, SYSCLK, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(CLK_32K_IN, SYSCLK, NORMAL, NORMAL, INPUT),
+
+ /* PCI */
+ DEFAULT_PINMUX(PEX_L0_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L0_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L0_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_WAKE_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L1_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L1_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L1_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L2_PRSNT_N, PCIE, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(PEX_L2_RST_N, PCIE, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(PEX_L2_CLKREQ_N, PCIE, NORMAL, NORMAL, INPUT),
+
+ /* HDMI */
+ DEFAULT_PINMUX(HDMI_CEC, CEC, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(HDMI_INT, RSVD1, NORMAL, TRISTATE, INPUT),
+};
+
+static struct pingroup_config unused_pins_lowpower[] = {
+ /* UART1 - NC */
+ DEFAULT_PINMUX(ULPI_DATA2, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA3, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA4, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA5, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA6, UARTA, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(ULPI_DATA7, UARTA, NORMAL, NORMAL, INPUT),
+
+ /* UART2 - NC */
+ DEFAULT_PINMUX(UART2_RTS_N, UARTB, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(UART2_CTS_N, UARTB, NORMAL, NORMAL, INPUT),
+
+ /* DAP - NC */
+ DEFAULT_PINMUX(CLK1_REQ, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK3_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK3_REQ, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* DAP4 - NC */
+ DEFAULT_PINMUX(DAP4_DOUT, I2S3, NORMAL, NORMAL, INPUT),
+
+ /* Tamonten GPIO - NC */
+ DEFAULT_PINMUX(CLK2_OUT, EXTPERIPH2, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(CLK2_REQ, DAP, NORMAL, NORMAL, INPUT),
+
+ /* BT656 - NC */
+ LV_PINMUX(VI_D0, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D1, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+ LV_PINMUX(VI_D10, RSVD1, NORMAL, NORMAL, INPUT, DISABLE, DISABLE),
+
+ /* GPIO - NC */
+ DEFAULT_PINMUX(GPIO_PU0, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU2, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PU4, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Video input - NC */
+ DEFAULT_PINMUX(CAM_MCLK, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB3, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB5, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB6, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW11, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* KBC keys - NC */
+ DEFAULT_PINMUX(KB_ROW0, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW1, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW2, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW3, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW4, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW5, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW6, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW7, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW8, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW9, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW10, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW12, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW13, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW14, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_ROW15, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL0, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL1, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL2, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL3, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL4, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL5, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL6, KBC, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(KB_COL7, KBC, UP, NORMAL, INPUT),
+
+ /* PMU - NC */
+ DEFAULT_PINMUX(CLK_32K_OUT, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Power rails GPIO - NC */
+ DEFAULT_PINMUX(SPI2_SCK, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PBB4, RSVD1, NORMAL, NORMAL, INPUT),
+
+ /* Others - NC */
+ DEFAULT_PINMUX(GMI_WP_N, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GPIO_PV1, RSVD1, NORMAL, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_WAIT, NAND, UP, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_ADV_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_CLK, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_CS3_N, NAND, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_CS7_N, NAND, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_AD0, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD1, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD2, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD3, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD4, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD5, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD6, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD7, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD9, PWM1, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD11, NAND, NORMAL, NORMAL, OUTPUT),
+ DEFAULT_PINMUX(GMI_AD13, NAND, UP, NORMAL, INPUT),
+ DEFAULT_PINMUX(GMI_WR_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_OE_N, NAND, NORMAL, TRISTATE, OUTPUT),
+ DEFAULT_PINMUX(GMI_DQS, NAND, NORMAL, TRISTATE, OUTPUT),
+};
+
+static struct padctrl_config tamonten_ng_padctrl[] = {
+ /* (_padgrp, _slwf, _slwr, _drvup, _drvdn, _lpmd, _schmt, _hsm) */
+ DEFAULT_PADCFG(SDIO1, SDIOCFG_DRVUP_SLWF, SDIOCFG_DRVDN_SLWR,
+ SDIOCFG_DRVUP, SDIOCFG_DRVDN, NONE, DISABLE, DISABLE),
+};
+#endif /* _PINMUX_CONFIG_TAMONTEN_NG_H_ */
diff --git a/board/avionic-design/common/tamonten-ng.c b/board/avionic-design/common/tamonten-ng.c
new file mode 100644
index 0000000..9d395c6
--- /dev/null
+++ b/board/avionic-design/common/tamonten-ng.c
@@ -0,0 +1,85 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/gp_padctrl.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+#include "pinmux-config-tamonten-ng.h"
+#include <i2c.h>
+
+#define PMU_I2C_ADDRESS 0x2D
+
+#define PMU_REG_LDO5 0x32
+
+#define PMU_REG_LDO_HIGH_POWER 1
+
+/* Voltage selection for the LDOs with 100mV resolution */
+#define PMU_REG_LDO_SEL_100(mV) ((((mV - 1000) / 100) + 2) << 2)
+
+#define PMU_REG_LDO_100(st, mV) (PMU_REG_LDO_##st | PMU_REG_LDO_SEL_100(mV))
+
+#define PMU_LDO5(st, mV) PMU_REG_LDO_100(st, mV)
+
+void pinmux_init(void)
+{
+ pinmux_config_table(tamonten_ng_pinmux_common,
+ ARRAY_SIZE(tamonten_ng_pinmux_common));
+ pinmux_config_table(unused_pins_lowpower,
+ ARRAY_SIZE(unused_pins_lowpower));
+
+ /* Initialize any non-default pad configs (APB_MISC_GP regs) */
+ padgrp_config_table(tamonten_ng_padctrl,
+ ARRAY_SIZE(tamonten_ng_padctrl));
+}
+
+void gpio_early_init(void)
+{
+ /* Turn on the alive signal */
+ gpio_request(GPIO_PV2, "ALIVE");
+ gpio_direction_output(GPIO_PV2, 1);
+
+ /* Remove the reset on the external periph */
+ gpio_request(GPIO_PI4, "nRST_PERIPH");
+ gpio_direction_output(GPIO_PI4, 1);
+}
+
+void pmu_write(uchar reg, uchar data)
+{
+ i2c_set_bus_num(4); /* PMU is on bus 4 */
+ i2c_write(PMU_I2C_ADDRESS, reg, 1, &data, 1);
+}
+
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+ /* Enable LDO5 with 3.3v for SDMMC3 */
+ pmu_write(PMU_REG_LDO5, PMU_LDO5(HIGH_POWER, 3300));
+
+ /* Switch the power on */
+ gpio_request(GPIO_PJ2, "EN_3V3_EMMC");
+ gpio_direction_output(GPIO_PJ2, 1);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+ /*
+ * NOTE: We don't do mmc-specific pin muxes here.
+ * They were done globally in pinmux_init().
+ */
+
+ /* Bring up the SDIO1 power rail */
+ board_sdmmc_voltage_init();
+}
diff --git a/board/avionic-design/dts/tegra30-tamonten.dtsi b/board/avionic-design/dts/tegra30-tamonten.dtsi
new file mode 100644
index 0000000..50d5762
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tamonten.dtsi
@@ -0,0 +1,69 @@
+#include "tegra30.dtsi"
+
+/ {
+ model = "Avionic Design Tamonten NG";
+ compatible = "ad,tamonten-ng", "nvidia,tegra30";
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ aliases {
+ i2c0 = "/i2c at 7000c000";
+ i2c1 = "/i2c at 7000c700";
+ i2c2 = "/i2c at 7000c400";
+ i2c3 = "/i2c at 7000c500";
+ i2c4 = "/i2c at 7000d000";
+ sdhci0 = "/sdhci at 78000600";
+ sdhci1 = "/sdhci at 78000400";
+ sdhci2 = "/sdhci at 78000000";
+ usb0 = "/usb at 7d008000";
+ };
+
+ /* GEN1 */
+ i2c at 7000c000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* GEN2 */
+ i2c at 7000c400 {
+ clock-frequency = <100000>;
+ };
+
+ /* CAM */
+ i2c at 7000c500 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* DDC */
+ i2c at 7000c700 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* PWR */
+ i2c at 7000d000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ /* SD slot on the base board */
+ sdhci at 78000400 {
+ cd-gpios = <&gpio 69 1>; /* gpio PI5 */
+ wp-gpios = <&gpio 67 0>; /* gpio PI3 */
+ bus-width = <4>;
+ };
+
+ /* EMMC on the COM module */
+ sdhci at 78000600 {
+ status = "okay";
+ bus-width = <8>;
+ };
+
+ usb at 7d008000 {
+ status = "okay";
+ };
+
+};
diff --git a/board/avionic-design/dts/tegra30-tec-ng.dts b/board/avionic-design/dts/tegra30-tec-ng.dts
new file mode 100644
index 0000000..8a69e81
--- /dev/null
+++ b/board/avionic-design/dts/tegra30-tec-ng.dts
@@ -0,0 +1,18 @@
+/dts-v1/;
+
+#include "tegra30-tamonten.dtsi"
+
+/ {
+ model = "Avionic Design Tamonten? NG Evaluation Carrier";
+ compatible = "ad,tec-ng", "nvidia,tegra30";
+
+ /* GEN2 */
+ i2c at 7000c400 {
+ status = "okay";
+ };
+
+ /* SD card slot */
+ sdhci at 78000400 {
+ status = "okay";
+ };
+};
diff --git a/board/avionic-design/tec-ng/Makefile b/board/avionic-design/tec-ng/Makefile
new file mode 100644
index 0000000..f41eb30
--- /dev/null
+++ b/board/avionic-design/tec-ng/Makefile
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2013
+# Avionic Design GmbH <www.avionic-design.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+$(shell mkdir -p $(obj)../common $(obj)../../nvidia/common)
+
+obj-y := ../common/tamonten-ng.o
+
+include ../../nvidia/common/common.mk
diff --git a/boards.cfg b/boards.cfg
index caba64e..fc5cb2d 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -353,6 +353,7 @@ Active arm armv7:arm720t tegra114 nvidia dalmore
Active arm armv7:arm720t tegra20 avionic-design medcom-wide medcom-wide - Thierry Reding <thierry.reding@avionic-design.de>
Active arm armv7:arm720t tegra20 avionic-design plutux plutux - Thierry Reding <thierry.reding@avionic-design.de>
Active arm armv7:arm720t tegra20 avionic-design tec tec - Thierry Reding <thierry.reding@avionic-design.de>
+Active arm armv7:arm720t tegra30 avionic-design tec-ng tec-ng - Alban Bedel <alban.bedel@avionic-design.de>
Active arm armv7:arm720t tegra20 compal paz00 paz00 - Tom Warren <twarren@nvidia.com>:Stephen Warren <swarren@nvidia.com>
Active arm armv7:arm720t tegra20 compulab trimslice trimslice - Tom Warren <twarren@nvidia.com>:Stephen Warren <swarren@nvidia.com>
Active arm armv7:arm720t tegra20 nvidia harmony harmony - Tom Warren <twarren@nvidia.com>
diff --git a/include/configs/tec-ng.h b/include/configs/tec-ng.h
new file mode 100644
index 0000000..13baa76
--- /dev/null
+++ b/include/configs/tec-ng.h
@@ -0,0 +1,84 @@
+/*
+ * (C) Copyright 2013
+ * Avionic Design GmbH <www.avionic-design.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "tegra30-common.h"
+
+/* Enable fdt support for tec-ng. Flash the image in u-boot-dtb.bin */
+#define CONFIG_DEFAULT_DEVICE_TREE tegra30-tec-ng
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* High-level configuration options */
+#define V_PROMPT "Tegra30 (TEC-NG) # "
+#define CONFIG_TEGRA_BOARD_STRING "Avionic Design Tamonten? NG Evaluation Carrier"
+
+/* Board-specific serial config */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_TEGRA_ENABLE_UARTD
+#define CONFIG_SYS_NS16550_COM1 NV_PA_APB_UARTD_BASE
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* I2C */
+#define CONFIG_SYS_I2C_TEGRA
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_MAX_I2C_BUS TEGRA_I2C_NUM_CONTROLLERS
+#define CONFIG_SYS_I2C_SPEED 100000
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_TEGRA_MMC
+#define CONFIG_CMD_MMC
+
+/* Environment in eMMC, at the end of 2nd "boot sector" */
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE)
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_SYS_MMC_ENV_PART 2
+
+/* SPI */
+#define CONFIG_TEGRA20_SLINK
+#define CONFIG_TEGRA_SLINK_CTRLS 6
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED 24000000
+#define CONFIG_CMD_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_SIZE (4 << 20)
+
+/* USB Host support */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_TEGRA
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_USB
+
+/* USB networking support */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+
+/* General networking support */
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+
+/* Tag support */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+/* support the new (FDT-based) image format */
+#define CONFIG_FIT
+
+#include "tegra-common-post.h"
+
+#endif /* __CONFIG_H */
--
1.8.4.2
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [U-Boot] [PATCH v5] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board
2013-11-14 9:58 ` [U-Boot] [PATCH v5] " Alban Bedel
@ 2013-11-14 22:45 ` Stephen Warren
0 siblings, 0 replies; 8+ messages in thread
From: Stephen Warren @ 2013-11-14 22:45 UTC (permalink / raw)
To: u-boot
On 11/14/2013 02:58 AM, Alban Bedel wrote:
> Add support for the new Tamonten? NG platform from Avionic Design.
> Currently only I2C, MMC, USB and ethernet have been tested.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
It's odd to take patch v4 3/3, revise that, and just repost that one
patch, since now Tom has to take patch 1/3 and 2/3 from v4 and patch 3/3
from v5. Still, I guess he can work that out.
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2013-11-14 22:45 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-11-13 16:27 [U-Boot] [PATCH v4 0/3] ARM: tegra: Add the Tamonten-NG Evaluation carrier boards Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 1/3] ARM: tegra: support SKU b1 of Tegra30 Alban Bedel
2013-11-13 16:27 ` [U-Boot] [PATCH v4 2/3] i2c: tegra: Add the fifth bus on SoC with more than 4 buses Alban Bedel
2013-11-14 5:27 ` Heiko Schocher
2013-11-13 16:27 ` [U-Boot] [PATCH v4 3/3] ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board Alban Bedel
2013-11-13 17:37 ` Stephen Warren
2013-11-14 9:58 ` [U-Boot] [PATCH v5] " Alban Bedel
2013-11-14 22:45 ` Stephen Warren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.