From mboxrd@z Thu Jan 1 00:00:00 1970 From: andrew@lunn.ch (Andrew Lunn) Date: Sat, 15 Feb 2014 11:20:03 +0100 Subject: [PATCH v2 05/23] ARM: Kirkwood: Seperate board-dt from common and pcie code. In-Reply-To: <1392459621-24003-1-git-send-email-andrew@lunn.ch> References: <1392459621-24003-1-git-send-email-andrew@lunn.ch> Message-ID: <1392459621-24003-6-git-send-email-andrew@lunn.ch> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org In order to be able to move DT support into mach-mvebu, the DT code needs to be cleanly separated from common and pcie code. Import the needed bits of these files into board-dt.c. The "common" code then becomes purely legacy, supporting none DT boards, so reflect this in the Makefile targets. Signed-off-by: Andrew Lunn --- arch/arm/mach-kirkwood/Makefile | 3 +- arch/arm/mach-kirkwood/board-dt.c | 88 ++++++++++++++++++++++++++++++++++++++- 2 files changed, 88 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-kirkwood/Makefile b/arch/arm/mach-kirkwood/Makefile index dc22bf5b21ed..3a72c5c6e747 100644 --- a/arch/arm/mach-kirkwood/Makefile +++ b/arch/arm/mach-kirkwood/Makefile @@ -1,5 +1,4 @@ -obj-y += common.o pcie.o -obj-$(CONFIG_KIRKWOOD_LEGACY) += irq.o mpp.o +obj-$(CONFIG_KIRKWOOD_LEGACY) += irq.o mpp.o common.o pcie.o obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2-setup.o lacie_v2-common.o diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c index a0c0ff39788e..64151a4a378f 100644 --- a/arch/arm/mach-kirkwood/board-dt.c +++ b/arch/arm/mach-kirkwood/board-dt.c @@ -21,11 +21,97 @@ #include #include #include +#include #include #include -#include "common.h" +#include +#include #include "pm.h" +static struct map_desc kirkwood_io_desc[] __initdata = { + { + .virtual = (unsigned long) KIRKWOOD_REGS_VIRT_BASE, + .pfn = __phys_to_pfn(KIRKWOOD_REGS_PHYS_BASE), + .length = KIRKWOOD_REGS_SIZE, + .type = MT_DEVICE, + }, +}; + +static void __init kirkwood_map_io(void) +{ + iotable_init(kirkwood_io_desc, ARRAY_SIZE(kirkwood_io_desc)); +} + +static void __init kirkwood_l2_init(void) +{ +#ifdef CONFIG_CACHE_FEROCEON_L2 +#ifdef CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH + writel(readl(L2_CONFIG_REG) | L2_WRITETHROUGH, L2_CONFIG_REG); + feroceon_l2_init(1); +#else + writel(readl(L2_CONFIG_REG) & ~L2_WRITETHROUGH, L2_CONFIG_REG); + feroceon_l2_init(0); +#endif +#endif +} + +static struct resource kirkwood_cpufreq_resources[] = { + [0] = { + .start = CPU_CONTROL_PHYS, + .end = CPU_CONTROL_PHYS + 3, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device kirkwood_cpufreq_device = { + .name = "kirkwood-cpufreq", + .id = -1, + .num_resources = ARRAY_SIZE(kirkwood_cpufreq_resources), + .resource = kirkwood_cpufreq_resources, +}; + +static void __init kirkwood_cpufreq_init(void) +{ + platform_device_register(&kirkwood_cpufreq_device); +} + +static struct resource kirkwood_cpuidle_resource[] = { + { + .flags = IORESOURCE_MEM, + .start = DDR_OPERATION_BASE, + .end = DDR_OPERATION_BASE + 3, + }, +}; + +static struct platform_device kirkwood_cpuidle = { + .name = "kirkwood_cpuidle", + .id = -1, + .resource = kirkwood_cpuidle_resource, + .num_resources = 1, +}; + +static void __init kirkwood_cpuidle_init(void) +{ + platform_device_register(&kirkwood_cpuidle); +} + +/* Temporary here since mach-mvebu has a function we can use */ +static void kirkwood_restart(enum reboot_mode mode, const char *cmd) +{ + /* + * Enable soft reset to assert RSTOUTn. + */ + writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK); + + /* + * Assert soft reset. + */ + writel(SOFT_RESET, SYSTEM_SOFT_RESET); + + while (1) + ; +} + #define MV643XX_ETH_MAC_ADDR_LOW 0x0414 #define MV643XX_ETH_MAC_ADDR_HIGH 0x0418 -- 1.8.5.3