* [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support
@ 2014-05-08 5:16 Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE Tim Harvey
` (11 more replies)
0 siblings, 12 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
This series adds some necessary framework for IMX6 SPL support. The series
includes support for NAND SPL and has been tested with MMC as well. I have
tested this on five differing Ventana baseboards with a variety of memory
(32bit 512MB, 32bit 1024MB, 64bit 1024MB) and CPU configurations (IMX6Q,
IMX6DL, IMX6S).
This is based on top of Mashahiro Yamada's patch that consolidates
arch/arm/include/asm/arch-*/spl.h [1]
v3:
- re-ordered calls in board_init_f
- replace imx_iomux_v3_setup_multiple_pads_array with additional intelligence
in imx_iomux_v3_setup_multiple_pads
- added ifdef's around cpu specific mmdc iocfg functions for code-reduction
with single-variant board configs
- added checks for IMX6D
- added Freescale copyright to boot device support function
- fixed typo s/IMX6SLD/IMX6SDL
- encorporated cleanups in mxs_nand_spl.c per feedback
v2:
- use compatible linker script instead of creating new one
- remove structure passing data from SPL to u-boot
- remove dependence on mtdpart, mtdcore, nand_util, nand_ecc, nand_base
and nand_bbt to bring SPL down in size. This reduced codesize by about 32k
where now mxs_spl_nand is about 12k total
- adjust CONFIG_SPL_TEXT_BASE, CONFIG_SPL_STACK and CONFIG_SPL_MAX_SIZE
to accomodate the IMX6SOLO/DUALLITE which have half the iRAM of the
IMX6DUAL/IMX6QUAD
- move boot dev detection into imx-common/spl.c
- move macros for using pinmux array into iomux-v3.h
- remove missing/unnecessary include
- revert mtdparts change
- use get_ram_size() to detect memory
- add support for MX6SOLO and MX6DUAL
- set CS0_END for 4GB so get_ram_size() works
- updated DDR3 calibration values for ventana boards
- fixed build issue - only compile spl if doing spl build
- fixed line length issue in README
- remove CONFIG_SPL* conditions and conditionally compile instead
- removed prints for CPU type and DRAM size/width - uboot will print these l
- removed unused gw_ventana_spl.cfg
- use common read_eeprom function
- added MMC support to SPL
- added Masahiro Yamada's boot mode consolidation patch
http://patchwork.ozlabs.org/patch/341817 and rebase on top of it
[1] http://patchwork.ozlabs.org/patch/341817/
Tim Harvey (11):
SPL: NAND: remove CONFIG_SYS_NAND_PAGE_SIZE
SPL: NAND: add support for mxs nand
MX6: add common SPL configuration
MX6: add boot device support for SPL
IMX: add comments and remove unused struct fields
MX6: add structs for mmdc and ddr iomux registers
MX6: add mmdc configuration for MX6Q/MX6DL
IMX: iomux: add macros to setup iomux for multiple SoC types
IMX: ventana: split read_eeprom into standalone file
IMX: ventana: auto-configure for IMX6Q vs IMX6DL
IMX: ventana: switch to SPL
arch/arm/cpu/armv7/mx6/Makefile | 1 +
arch/arm/cpu/armv7/mx6/ddr.c | 473 ++++++++++++++++++++++
arch/arm/imx-common/Makefile | 1 +
arch/arm/imx-common/cpu.c | 16 +-
arch/arm/imx-common/iomux-v3.c | 16 +-
arch/arm/imx-common/spl.c | 81 ++++
arch/arm/include/asm/arch-mx6/mx6-ddr.h | 231 +++++++++++
arch/arm/include/asm/imx-common/iomux-v3.h | 25 ++
board/gateworks/gw_ventana/Makefile | 3 +-
board/gateworks/gw_ventana/README | 92 +++--
board/gateworks/gw_ventana/eeprom.c | 89 +++++
board/gateworks/gw_ventana/gw_ventana.c | 591 +++++++++++++++-------------
board/gateworks/gw_ventana/gw_ventana.cfg | 15 -
board/gateworks/gw_ventana/gw_ventana_spl.c | 419 ++++++++++++++++++++
board/gateworks/gw_ventana/ventana_eeprom.h | 11 +
boards.cfg | 6 +-
common/spl/spl_nand.c | 2 +-
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/mxs_nand_spl.c | 231 +++++++++++
include/configs/gw_ventana.h | 11 +
include/configs/imx6_spl.h | 71 ++++
21 files changed, 2047 insertions(+), 339 deletions(-)
create mode 100644 arch/arm/cpu/armv7/mx6/ddr.c
create mode 100644 arch/arm/imx-common/spl.c
create mode 100644 board/gateworks/gw_ventana/eeprom.c
create mode 100644 board/gateworks/gw_ventana/gw_ventana_spl.c
create mode 100644 drivers/mtd/nand/mxs_nand_spl.c
create mode 100644 include/configs/imx6_spl.h
--
1.8.3.2
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-14 8:52 ` Masahiro Yamada
2014-05-15 8:31 ` Stefano Babic
2014-05-08 5:16 ` [U-Boot] [PATCH v3 02/11] spl: nand: add support for mxs nand Tim Harvey
` (10 subsequent siblings)
11 siblings, 2 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
We only need to read in the size of struct image_header and thus don't
need to know the page size of the nand device.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
---
v3:
- no changes
v2:
- cc Scott Wood <scottwood@freescale.com> on this
- Acked-by: Stefano Babic <sbabic@denx.de>
- Acked-by: Scott Wood <scottwood@freescale.com>
---
common/spl/spl_nand.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/common/spl/spl_nand.c b/common/spl/spl_nand.c
index 9da0218..062461b 100644
--- a/common/spl/spl_nand.c
+++ b/common/spl/spl_nand.c
@@ -76,7 +76,7 @@ void spl_nand_load_image(void)
#endif
/* Load u-boot */
nand_spl_load_image(CONFIG_SYS_NAND_U_BOOT_OFFS,
- CONFIG_SYS_NAND_PAGE_SIZE, (void *)header);
+ sizeof(*header), (void *)header);
spl_parse_image_header(header);
nand_spl_load_image(CONFIG_SYS_NAND_U_BOOT_OFFS,
spl_image.size, (void *)spl_image.load_addr);
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 02/11] spl: nand: add support for mxs nand
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 03/11] mx6: add common SPL configuration Tim Harvey
` (9 subsequent siblings)
11 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
This utilizes existing mxs_nand support layer to provide a method to load an
image off nand for SPL. The flash device will be detected in order to support
multiple flash devices instead of having layout hard coded at build time.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- removed NAND_NCE and NAND_CTRL_CHANGE unused by mxc_nand.c
- return specific error types on errors
- remove register keyword - let compiler do optimizations
v2:
- remove dependence on mtdpart, mtdcore, nand_util, nand_ecc, nand_base
and nand_bbt to bring SPL down in size. This reduced codesize by about 32k
where now mxs_spl_nand is about 12k total.
---
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/mxs_nand_spl.c | 231 ++++++++++++++++++++++++++++++++++++++++
2 files changed, 232 insertions(+)
create mode 100644 drivers/mtd/nand/mxs_nand_spl.c
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 02b149c..de5b461 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -65,5 +65,6 @@ else # minimal SPL drivers
obj-$(CONFIG_NAND_FSL_ELBC) += fsl_elbc_spl.o
obj-$(CONFIG_NAND_FSL_IFC) += fsl_ifc_spl.o
obj-$(CONFIG_NAND_MXC) += mxc_nand_spl.o
+obj-$(CONFIG_NAND_MXS) += mxs_nand_spl.o mxs_nand.o
endif # drivers
diff --git a/drivers/mtd/nand/mxs_nand_spl.c b/drivers/mtd/nand/mxs_nand_spl.c
new file mode 100644
index 0000000..78ca32c
--- /dev/null
+++ b/drivers/mtd/nand/mxs_nand_spl.c
@@ -0,0 +1,231 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <nand.h>
+#include <malloc.h>
+
+static nand_info_t mtd;
+static struct nand_chip nand_chip;
+
+static void mxs_nand_command(struct mtd_info *mtd, unsigned int command,
+ int column, int page_addr)
+{
+ register struct nand_chip *chip = mtd->priv;
+ u32 timeo, time_start;
+
+ /* write out the command to the device */
+ chip->cmd_ctrl(mtd, command, NAND_CLE);
+
+ /* Serially input address */
+ if (column != -1) {
+ chip->cmd_ctrl(mtd, column, NAND_ALE);
+ chip->cmd_ctrl(mtd, column >> 8, NAND_ALE);
+ }
+ if (page_addr != -1) {
+ chip->cmd_ctrl(mtd, page_addr, NAND_ALE);
+ chip->cmd_ctrl(mtd, page_addr >> 8, NAND_ALE);
+ /* One more address cycle for devices > 128MiB */
+ if (chip->chipsize > (128 << 20))
+ chip->cmd_ctrl(mtd, page_addr >> 16, NAND_ALE);
+ }
+ chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0);
+
+ if (command == NAND_CMD_READ0) {
+ chip->cmd_ctrl(mtd, NAND_CMD_READSTART, NAND_CLE);
+ chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0);
+ }
+
+ /* wait for nand ready */
+ ndelay(100);
+ timeo = (CONFIG_SYS_HZ * 20) / 1000;
+ time_start = get_timer(0);
+ while (get_timer(time_start) < timeo) {
+ if (chip->dev_ready(mtd))
+ break;
+ }
+}
+
+static int mxs_flash_ident(struct mtd_info *mtd)
+{
+ register struct nand_chip *chip = mtd->priv;
+ int i;
+ u8 mfg_id, dev_id;
+ u8 id_data[8];
+ struct nand_onfi_params *p = &chip->onfi_params;
+
+ /* Reset the chip */
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+
+ /* Send the command for reading device ID */
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+
+ /* Read manufacturer and device IDs */
+ mfg_id = chip->read_byte(mtd);
+ dev_id = chip->read_byte(mtd);
+
+ /* Try again to make sure */
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+ for (i = 0; i < 8; i++)
+ id_data[i] = chip->read_byte(mtd);
+ if (id_data[0] != mfg_id || id_data[1] != dev_id) {
+ printf("second ID read did not match");
+ return -1;
+ }
+ debug("0x%02x:0x%02x ", mfg_id, dev_id);
+
+ /* read ONFI */
+ chip->onfi_version = 0;
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1);
+ if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' ||
+ chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I') {
+ return -2;
+ }
+
+ /* we have ONFI, probe it */
+ chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1);
+ chip->read_buf(mtd, (uint8_t *)p, sizeof(*p));
+ mtd->name = p->model;
+ mtd->writesize = le32_to_cpu(p->byte_per_page);
+ mtd->erasesize = le32_to_cpu(p->pages_per_block) * mtd->writesize;
+ mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page);
+ chip->chipsize = le32_to_cpu(p->blocks_per_lun);
+ chip->chipsize *= (uint64_t)mtd->erasesize * p->lun_count;
+ /* Calculate the address shift from the page size */
+ chip->page_shift = ffs(mtd->writesize) - 1;
+ chip->phys_erase_shift = ffs(mtd->erasesize) - 1;
+ /* Convert chipsize to number of pages per chip -1 */
+ chip->pagemask = (chip->chipsize >> chip->page_shift) - 1;
+ chip->badblockbits = 8;
+
+ debug("erasesize=%d (>>%d)\n", mtd->erasesize, chip->phys_erase_shift);
+ debug("writesize=%d (>>%d)\n", mtd->writesize, chip->page_shift);
+ debug("oobsize=%d\n", mtd->oobsize);
+ debug("chipsize=%lld\n", chip->chipsize);
+
+ return 0;
+}
+
+static int mxs_read_page_ecc(struct mtd_info *mtd, void *buf, unsigned int page)
+{
+ register struct nand_chip *chip = mtd->priv;
+ int ret;
+
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, page);
+ ret = nand_chip.ecc.read_page(mtd, chip, buf, 1, page);
+ if (ret < 0) {
+ printf("read_page failed %d\n", ret);
+ return -1;
+ }
+ return 0;
+}
+
+static int is_badblock(struct mtd_info *mtd, loff_t offs, int allowbbt)
+{
+ register struct nand_chip *chip = mtd->priv;
+ unsigned int block = offs >> chip->phys_erase_shift;
+ unsigned int page = offs >> chip->page_shift;
+
+ debug("%s offs=0x%08x block:%d page:%d\n", __func__, (int)offs, block,
+ page);
+ chip->cmdfunc(mtd, NAND_CMD_READ0, mtd->writesize, page);
+ memset(chip->oob_poi, 0, mtd->oobsize);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+ return (chip->oob_poi[0] != 0xff);
+}
+
+/* setup mtd and nand structs and init mxs_nand driver */
+static int mxs_nand_init(void)
+{
+ /* return if already initalized */
+ if (nand_chip.numchips)
+ return 0;
+
+ /* init mxs nand driver */
+ board_nand_init(&nand_chip);
+ mtd.priv = &nand_chip;
+ /* set mtd functions */
+ nand_chip.cmdfunc = mxs_nand_command;
+ nand_chip.numchips = 1;
+
+ /* identify flash device */
+ puts("NAND : ");
+ if (mxs_flash_ident(&mtd)) {
+ printf("Failed to identify\n");
+ return -1;
+ }
+
+ /* allocate and initialize buffers */
+ nand_chip.buffers = memalign(ARCH_DMA_MINALIGN,
+ sizeof(*nand_chip.buffers));
+ nand_chip.oob_poi = nand_chip.buffers->databuf + mtd.writesize;
+ /* setup flash layout (does not scan as we override that) */
+ mtd.size = nand_chip.chipsize;
+ nand_chip.scan_bbt(&mtd);
+
+ printf("%llu MiB\n", (mtd.size / (1024 * 1024)));
+ return 0;
+}
+
+int nand_spl_load_image(uint32_t offs, unsigned int size, void *buf)
+{
+ struct nand_chip *chip;
+ unsigned int page;
+ unsigned int nand_page_per_block;
+ unsigned int sz = 0;
+
+ if (mxs_nand_init())
+ return -ENODEV;
+ chip = mtd.priv;
+ page = offs >> chip->page_shift;
+ nand_page_per_block = mtd.erasesize / mtd.writesize;
+
+ debug("%s offset:0x%08x len:%d page:%d\n", __func__, offs, size, page);
+
+ size = roundup(size, mtd.writesize);
+ while (sz < size) {
+ if (mxs_read_page_ecc(&mtd, buf, page) < 0)
+ return -1;
+ sz += mtd.writesize;
+ offs += mtd.writesize;
+ page++;
+ buf += mtd.writesize;
+
+ /*
+ * Check if we have crossed a block boundary, and if so
+ * check for bad block.
+ */
+ if (!(page % nand_page_per_block)) {
+ /*
+ * Yes, new block. See if this block is good. If not,
+ * loop until we find a good block.
+ */
+ while (is_badblock(&mtd, offs, 1)) {
+ page = page + nand_page_per_block;
+ /* Check i we've reached the end of flash. */
+ if (page >= mtd.size >> chip->page_shift)
+ return -ENOMEM;
+ }
+ }
+ }
+
+ return 0;
+}
+
+int nand_default_bbt(struct mtd_info *mtd)
+{
+ return 0;
+}
+
+void nand_init(void)
+{
+}
+
+void nand_deselect(void)
+{
+}
+
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 03/11] mx6: add common SPL configuration
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 02/11] spl: nand: add support for mxs nand Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL Tim Harvey
` (8 subsequent siblings)
11 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Add a common header which can hopefully be shared amon imx6 SPL users
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
---
v3:
- fixed typo s/IMX6SLD/IMX6SDL
- add acks from Stefano and Nikita
v2:
- adjust CONFIG_SPL_TEXT_BASE, CONFIG_SPL_STACK and CONFIG_SPL_MAX_SIZE
to accomodate the IMX6SOLO/DUALLITE which have half the iRAM of the
IMX6DUAL/IMX6QUAD
---
include/configs/imx6_spl.h | 71 ++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 71 insertions(+)
create mode 100644 include/configs/imx6_spl.h
diff --git a/include/configs/imx6_spl.h b/include/configs/imx6_spl.h
new file mode 100644
index 0000000..6fdc438
--- /dev/null
+++ b/include/configs/imx6_spl.h
@@ -0,0 +1,71 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __IMX6_SPL_CONFIG_H
+#define __IMX6_SPL_CONFIG_H
+
+#ifdef CONFIG_SPL
+
+#define CONFIG_SPL_FRAMEWORK
+
+/*
+ * see Figure 8-3 in IMX6DQ/IMX6SDL Reference manuals:
+ * - IMX6SDL OCRAM (IRAM) is from 0x00907000 to 0x0091FFFF
+ * - IMX6DQ has 2x IRAM of IMX6SDL but we intend to support IMX6SDL as well
+ * - BOOT ROM stack is at 0x0091FFB8
+ * - if icache/dcache is enabled (eFuse/strapping controlled) then the
+ * IMX BOOT ROM will setup MMU table at 0x00918000, therefore we need to
+ * fit between 0x00907000 and 0x00918000.
+ * - Additionally the BOOT ROM loads what they consider the firmware image
+ * which consists of a 4K header in front of us that contains the IVT, DCD
+ * and some padding thus 'our' max size is really 0x00908000 - 0x00918000
+ * or 64KB
+ */
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/omap-common/u-boot-spl.lds"
+#define CONFIG_SPL_TEXT_BASE 0x00908000
+#define CONFIG_SPL_MAX_SIZE (64 * 1024)
+#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/armv7"
+#define CONFIG_SPL_STACK 0x0091FFB8
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+/* NAND support */
+#if defined(CONFIG_SPL_NAND_SUPPORT)
+#define CONFIG_SPL_NAND_MXS
+#define CONFIG_SPL_DMA_SUPPORT
+#endif
+
+/* MMC support */
+#if defined(CONFIG_SPL_MMC_SUPPORT)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 138 /* offset 69KB */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 800 /* 400 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
+#define CONFIG_SYS_MONITOR_LEN (CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS/2*1024)
+#endif
+
+/* SATA support */
+#if defined(CONFIG_SPL_SATA_SUPPORT)
+#define CONFIG_SPL_SATA_BOOT_DEVICE 0
+#define CONFIG_SYS_SATA_FAT_BOOT_PARTITION 1
+#endif
+
+/* Define the payload for FAT/EXT support */
+#if defined(CONFIG_SPL_FAT_SUPPORT) || defined(CONFIG_SPL_EXT_SUPPORT)
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#endif
+
+#define CONFIG_SPL_BSS_START_ADDR 0x18200000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
+#define CONFIG_SYS_SPL_MALLOC_START 0x18300000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x3200000 /* 50 MB */
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+#endif
+
+#endif
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (2 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 03/11] mx6: add common SPL configuration Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-28 16:38 ` Nikita Kiryanov
2014-05-08 5:16 ` [U-Boot] [PATCH v3 05/11] imx: add comments and remove unused struct fields Tim Harvey
` (7 subsequent siblings)
11 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Add a common spl.c file to support boot device functions needed for SPL
such as detecting the boot device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- added Freescale copyright
v2:
- re-base on top of Masahiro Yamada's consolidation patch:
http://patchwork.ozlabs.org/patch/341817/
- moved spl_boot_device() and get_boot_mode() into own common imx spl.c file
- use mem-mapped structure for smbr reg access
---
arch/arm/imx-common/Makefile | 1 +
arch/arm/imx-common/spl.c | 81 ++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 82 insertions(+)
create mode 100644 arch/arm/imx-common/spl.c
diff --git a/arch/arm/imx-common/Makefile b/arch/arm/imx-common/Makefile
index b04dfbb..c97ea48 100644
--- a/arch/arm/imx-common/Makefile
+++ b/arch/arm/imx-common/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_SYS_I2C_MXC) += i2c-mxv7.o
endif
ifeq ($(SOC),$(filter $(SOC),mx6 mxs))
obj-y += misc.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
endif
ifeq ($(SOC),$(filter $(SOC),mx6))
obj-$(CONFIG_CMD_SATA) += sata.o
diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
new file mode 100644
index 0000000..9a02a64
--- /dev/null
+++ b/arch/arm/imx-common/spl.c
@@ -0,0 +1,81 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Copyright (C) 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/spl.h>
+#include <spl.h>
+
+#if defined(CONFIG_MX6)
+/* determine boot device from SRC_SBMR1 register (BOOT_CFG[4:1]) */
+u32 spl_boot_device(void)
+{
+ struct src *psrc = (struct src *)SRC_BASE_ADDR;
+ unsigned reg = readl(&psrc->sbmr1);
+
+ /* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
+ switch ((reg & 0x000000FF) >> 4) {
+ /* EIM: See 8.5.1, Table 8-9 */
+ case 0x0:
+ /* BOOT_CFG1[3]: NOR/OneNAND Selection */
+ if ((reg & 0x00000008) >> 3)
+ return BOOT_DEVICE_ONENAND;
+ else
+ return BOOT_DEVICE_NOR;
+ break;
+ /* SATA: See 8.5.4, Table 8-20 */
+ case 0x2:
+ return BOOT_DEVICE_SATA;
+ /* Serial ROM: See 8.5.5.1, Table 8-22 */
+ case 0x3:
+ /* BOOT_CFG4[2:0] */
+ switch ((reg & 0x07000000) >> 24) {
+ case 0x0 ... 0x4:
+ return BOOT_DEVICE_SPI;
+ case 0x5 ... 0x7:
+ return BOOT_DEVICE_I2C;
+ }
+ break;
+ /* SD/eSD: 8.5.3, Table 8-15 */
+ case 0x4:
+ case 0x5:
+ return BOOT_DEVICE_MMC1;
+ /* MMC/eMMC: 8.5.3 */
+ case 0x6:
+ case 0x7:
+ return BOOT_DEVICE_MMC1;
+ /* NAND Flash: 8.5.2 */
+ case 0x8 ... 0xf:
+ return BOOT_DEVICE_NAND;
+ }
+ return BOOT_DEVICE_NONE;
+}
+#endif
+
+#if defined(CONFIG_SPL_MMC_SUPPORT)
+/* called from spl_mmc to see type of boot mode for storage (RAW or FAT) */
+u32 spl_boot_mode(void)
+{
+ switch (spl_boot_device()) {
+ /* for MMC return either RAW or FAT mode */
+ case BOOT_DEVICE_MMC1:
+ case BOOT_DEVICE_MMC2:
+#ifdef CONFIG_SPL_FAT_SUPPORT
+ return MMCSD_MODE_FAT;
+#else
+ return MMCSD_MODE_RAW;
+#endif
+ break;
+ default:
+ puts("spl: ERROR: unsupported device\n");
+ hang();
+ }
+}
+#endif
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 05/11] imx: add comments and remove unused struct fields
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (3 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-28 16:38 ` Nikita Kiryanov
2014-05-08 5:16 ` [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers Tim Harvey
` (6 subsequent siblings)
11 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Add comment block for the imx_ddr_size function and remove the extra unused
fields from struct esd_mmdc_regs which are also not common between IMX53 and
IMX6.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
---
v3:
- fixed doxygen-style comment block
- added Stefano's Ack
v2:
- new patch in series
---
arch/arm/imx-common/cpu.c | 16 +++++++---------
1 file changed, 7 insertions(+), 9 deletions(-)
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index a77c4de..5a09107 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -58,6 +58,7 @@ char *get_reset_cause(void)
static const unsigned char col_lookup[] = {9, 10, 11, 8, 12, 9, 9, 9};
static const unsigned char bank_lookup[] = {3, 2};
+/* these MMDC registers are common to the IMX53 and IMX6 */
struct esd_mmdc_regs {
uint32_t ctl;
uint32_t pdc;
@@ -66,15 +67,6 @@ struct esd_mmdc_regs {
uint32_t cfg1;
uint32_t cfg2;
uint32_t misc;
- uint32_t scr;
- uint32_t ref;
- uint32_t rsvd1;
- uint32_t rsvd2;
- uint32_t rwd;
- uint32_t or;
- uint32_t mrr;
- uint32_t cfg3lp;
- uint32_t mr4;
};
#define ESD_MMDC_CTL_GET_ROW(mdctl) ((ctl >> 24) & 7)
@@ -83,6 +75,12 @@ struct esd_mmdc_regs {
#define ESD_MMDC_CTL_GET_CS1(mdctl) ((ctl >> 30) & 1)
#define ESD_MMDC_MISC_GET_BANK(mdmisc) ((misc >> 5) & 1)
+/*
+ * imx_ddr_size - return size in bytes of DRAM according MMDC config
+ * The MMDC MDCTL register holds the number of bits for row, col, and data
+ * width and the MMDC MDMISC register holds the number of banks. Combine
+ * all these bits to determine the meme size the MMDC has been configured for
+ */
unsigned imx_ddr_size(void)
{
struct esd_mmdc_regs *mem = (struct esd_mmdc_regs *)MEMCTL_BASE;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (4 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 05/11] imx: add comments and remove unused struct fields Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-28 17:06 ` Nikita Kiryanov
2014-05-08 5:16 ` [U-Boot] [PATCH v3 07/11] mx6: add mmdc configuration for MX6Q/MX6DL Tim Harvey
` (5 subsequent siblings)
11 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Add memory-mapped structures for MMDC iomux and configuration. Note that
the MMDC configuration registers are common between the IMX6DQ
(IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) the iomux
register addresses differ. This requires two sets of structures.
Add structures to describe DDR3 device information, system information
(memory layout, etc), and MMDC calibration regitsers that can be used to
configure the MMDC dynamically.
We define these structures for SPL builds instead of including mx6q-ddr.h an
mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- moved portions into following patch
v2:
- split out from original mmdc configuration patch
- only define for SPL build
- do not include mx6q-ddr.h and mx6dl-ddr.h for SPL build - these use the
same namespace and are only useful for imximage cfg files
---
arch/arm/include/asm/arch-mx6/mx6-ddr.h | 159 ++++++++++++++++++++++++++++++++
1 file changed, 159 insertions(+)
diff --git a/arch/arm/include/asm/arch-mx6/mx6-ddr.h b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
index 43d377a..c2a31d2 100644
--- a/arch/arm/include/asm/arch-mx6/mx6-ddr.h
+++ b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
@@ -6,6 +6,7 @@
#ifndef __ASM_ARCH_MX6_DDR_H__
#define __ASM_ARCH_MX6_DDR_H__
+#ifndef CONFIG_SPL_BUILD
#ifdef CONFIG_MX6Q
#include "mx6q-ddr.h"
#else
@@ -15,6 +16,164 @@
#error "Please select cpu"
#endif /* CONFIG_MX6DL or CONFIG_MX6S */
#endif /* CONFIG_MX6Q */
+#else
+
+/* MMDC P0/P1 Registers */
+struct mmdc_p_regs {
+ u32 mdctl;
+ u32 mdpdc;
+ u32 mdotc;
+ u32 mdcfg0;
+ u32 mdcfg1;
+ u32 mdcfg2;
+ u32 mdmisc;
+ u32 mdscr;
+ u32 mdref;
+ u32 res1[2];
+ u32 mdrwd;
+ u32 mdor;
+ u32 res2[3];
+ u32 mdasp;
+ u32 res3[240];
+ u32 mapsr;
+ u32 res4[254];
+ u32 mpzqhwctrl;
+ u32 res5[2];
+ u32 mpwldectrl0;
+ u32 mpwldectrl1;
+ u32 res6;
+ u32 mpodtctrl;
+ u32 mprddqby0dl;
+ u32 mprddqby1dl;
+ u32 mprddqby2dl;
+ u32 mprddqby3dl;
+ u32 res7[4];
+ u32 mpdgctrl0;
+ u32 mpdgctrl1;
+ u32 res8;
+ u32 mprddlctl;
+ u32 res9;
+ u32 mpwrdlctl;
+ u32 res10[25];
+ u32 mpmur0;
+};
+
+/*
+ * MMDC iomux registers (pinctl/padctl) - (different for IMX6DQ vs IMX6SDL)
+ */
+#define MX6DQ_IOM_DDR_BASE 0x020e0500
+struct mx6dq_iomux_ddr_regs {
+ u32 res1[3];
+ u32 dram_sdqs5;
+ u32 dram_dqm5;
+ u32 dram_dqm4;
+ u32 dram_sdqs4;
+ u32 dram_sdqs3;
+ u32 dram_dqm3;
+ u32 dram_sdqs2;
+ u32 dram_dqm2;
+ u32 res2[16];
+ u32 dram_cas;
+ u32 res3[2];
+ u32 dram_ras;
+ u32 dram_reset;
+ u32 res4[2];
+ u32 dram_sdclk_0;
+ u32 dram_sdba2;
+ u32 dram_sdcke0;
+ u32 dram_sdclk_1;
+ u32 dram_sdcke1;
+ u32 dram_sdodt0;
+ u32 dram_sdodt1;
+ u32 res5;
+ u32 dram_sdqs0;
+ u32 dram_dqm0;
+ u32 dram_sdqs1;
+ u32 dram_dqm1;
+ u32 dram_sdqs6;
+ u32 dram_dqm6;
+ u32 dram_sdqs7;
+ u32 dram_dqm7;
+};
+
+#define MX6DQ_IOM_GRP_BASE 0x020e0700
+struct mx6dq_iomux_grp_regs {
+ u32 res1[18];
+ u32 grp_b7ds;
+ u32 grp_addds;
+ u32 grp_ddrmode_ctl;
+ u32 res2;
+ u32 grp_ddrpke;
+ u32 res3[6];
+ u32 grp_ddrmode;
+ u32 res4[3];
+ u32 grp_b0ds;
+ u32 grp_b1ds;
+ u32 grp_ctlds;
+ u32 res5;
+ u32 grp_b2ds;
+ u32 grp_ddr_type;
+ u32 grp_b3ds;
+ u32 grp_b4ds;
+ u32 grp_b5ds;
+ u32 grp_b6ds;
+};
+
+#define MX6SDL_IOM_DDR_BASE 0x020e0400
+struct mx6sdl_iomux_ddr_regs {
+ u32 res1[25];
+ u32 dram_cas;
+ u32 res2[2];
+ u32 dram_dqm0;
+ u32 dram_dqm1;
+ u32 dram_dqm2;
+ u32 dram_dqm3;
+ u32 dram_dqm4;
+ u32 dram_dqm5;
+ u32 dram_dqm6;
+ u32 dram_dqm7;
+ u32 dram_ras;
+ u32 dram_reset;
+ u32 res3[2];
+ u32 dram_sdba2;
+ u32 dram_sdcke0;
+ u32 dram_sdcke1;
+ u32 dram_sdclk_0;
+ u32 dram_sdclk_1;
+ u32 dram_sdodt0;
+ u32 dram_sdodt1;
+ u32 dram_sdqs0;
+ u32 dram_sdqs1;
+ u32 dram_sdqs2;
+ u32 dram_sdqs3;
+ u32 dram_sdqs4;
+ u32 dram_sdqs5;
+ u32 dram_sdqs6;
+ u32 dram_sdqs7;
+};
+
+#define MX6SDL_IOM_GRP_BASE 0x020e0700
+struct mx6sdl_iomux_grp_regs {
+ u32 res1[18];
+ u32 grp_b7ds;
+ u32 grp_addds;
+ u32 grp_ddrmode_ctl;
+ u32 grp_ddrpke;
+ u32 res2[2];
+ u32 grp_ddrmode;
+ u32 grp_b0ds;
+ u32 res3;
+ u32 grp_ctlds;
+ u32 grp_b1ds;
+ u32 grp_ddr_type;
+ u32 grp_b2ds;
+ u32 grp_b3ds;
+ u32 grp_b4ds;
+ u32 grp_b5ds;
+ u32 res4;
+ u32 grp_b6ds;
+};
+#endif /* CONFIG_SPL_BUILD */
#define MX6_MMDC_P0_MDCTL 0x021b0000
#define MX6_MMDC_P0_MDPDC 0x021b0004
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 07/11] mx6: add mmdc configuration for MX6Q/MX6DL
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (5 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-22 22:28 ` [U-Boot] [PATCH v4 " Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 08/11] imx: iomux: add macros to setup iomux for multiple SoC types Tim Harvey
` (4 subsequent siblings)
11 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Add functions for configuring iomux based on board-specific regs and
for configuring mmdc based on board-specific and chip-specific data.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- added ifdef's around cpu specific iocfg functions for code-reduction with
single-variant board configs
- moved portions from previous patch here
- added check for IMX6D
v2:
- split out mmdc and iomux structs into separate patch
---
arch/arm/cpu/armv7/mx6/Makefile | 1 +
arch/arm/cpu/armv7/mx6/ddr.c | 473 ++++++++++++++++++++++++++++++++
arch/arm/include/asm/arch-mx6/mx6-ddr.h | 72 +++++
3 files changed, 546 insertions(+)
create mode 100644 arch/arm/cpu/armv7/mx6/ddr.c
diff --git a/arch/arm/cpu/armv7/mx6/Makefile b/arch/arm/cpu/armv7/mx6/Makefile
index d7285fc..6dc9f8e 100644
--- a/arch/arm/cpu/armv7/mx6/Makefile
+++ b/arch/arm/cpu/armv7/mx6/Makefile
@@ -8,4 +8,5 @@
#
obj-y := soc.o clock.o
+obj-$(CONFIG_SPL_BUILD) += ddr.o
obj-$(CONFIG_SECURE_BOOT) += hab.o
diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
new file mode 100644
index 0000000..e64fa91
--- /dev/null
+++ b/arch/arm/cpu/armv7/mx6/ddr.c
@@ -0,0 +1,473 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/types.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/types.h>
+
+#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
+/* Configure MX6DQ mmdc iomux */
+void mx6dq_dram_iocfg(unsigned width,
+ const struct mx6dq_iomux_ddr_regs *ddr,
+ const struct mx6dq_iomux_grp_regs *grp)
+{
+ volatile struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux;
+ volatile struct mx6dq_iomux_grp_regs *mx6_grp_iomux;
+
+ mx6_ddr_iomux = (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
+ mx6_grp_iomux = (struct mx6dq_iomux_grp_regs *)MX6DQ_IOM_GRP_BASE;
+
+ /* DDR IO Type */
+ mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
+ mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
+
+ /* Clock */
+ mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
+ mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1;
+
+ /* Address */
+ mx6_ddr_iomux->dram_cas = ddr->dram_cas;
+ mx6_ddr_iomux->dram_ras = ddr->dram_ras;
+ mx6_grp_iomux->grp_addds = grp->grp_addds;
+
+ /* Control */
+ mx6_ddr_iomux->dram_reset = ddr->dram_reset;
+ mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0;
+ mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1;
+ mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
+ mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0;
+ mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1;
+ mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
+
+ /* Data Strobes */
+ mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
+ mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
+ mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
+ mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4;
+ mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5;
+ mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6;
+ mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7;
+ }
+
+ /* Data */
+ mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
+ mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
+ mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
+ if (width >= 32) {
+ mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
+ mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
+ }
+ if (width >= 64) {
+ mx6_grp_iomux->grp_b4ds = grp->grp_b4ds;
+ mx6_grp_iomux->grp_b5ds = grp->grp_b5ds;
+ mx6_grp_iomux->grp_b6ds = grp->grp_b6ds;
+ mx6_grp_iomux->grp_b7ds = grp->grp_b7ds;
+ }
+ mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
+ mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
+ mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4;
+ mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5;
+ mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6;
+ mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7;
+ }
+}
+#endif
+
+#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
+/* Configure MX6SDL mmdc iomux */
+void mx6sdl_dram_iocfg(unsigned width,
+ const struct mx6sdl_iomux_ddr_regs *ddr,
+ const struct mx6sdl_iomux_grp_regs *grp)
+{
+ volatile struct mx6sdl_iomux_ddr_regs *mx6_ddr_iomux;
+ volatile struct mx6sdl_iomux_grp_regs *mx6_grp_iomux;
+
+ mx6_ddr_iomux = (struct mx6sdl_iomux_ddr_regs *)MX6SDL_IOM_DDR_BASE;
+ mx6_grp_iomux = (struct mx6sdl_iomux_grp_regs *)MX6SDL_IOM_GRP_BASE;
+
+ /* DDR IO Type */
+ mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
+ mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
+
+ /* Clock */
+ mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
+ mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1;
+
+ /* Address */
+ mx6_ddr_iomux->dram_cas = ddr->dram_cas;
+ mx6_ddr_iomux->dram_ras = ddr->dram_ras;
+ mx6_grp_iomux->grp_addds = grp->grp_addds;
+
+ /* Control */
+ mx6_ddr_iomux->dram_reset = ddr->dram_reset;
+ mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0;
+ mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1;
+ mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
+ mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0;
+ mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1;
+ mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
+
+ /* Data Strobes */
+ mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
+ mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
+ mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
+ mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4;
+ mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5;
+ mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6;
+ mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7;
+ }
+
+ /* Data */
+ mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
+ mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
+ mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
+ if (width >= 32) {
+ mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
+ mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
+ }
+ if (width >= 64) {
+ mx6_grp_iomux->grp_b4ds = grp->grp_b4ds;
+ mx6_grp_iomux->grp_b5ds = grp->grp_b5ds;
+ mx6_grp_iomux->grp_b6ds = grp->grp_b6ds;
+ mx6_grp_iomux->grp_b7ds = grp->grp_b7ds;
+ }
+ mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
+ mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
+ mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4;
+ mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5;
+ mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6;
+ mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7;
+ }
+}
+#endif
+
+/*
+ * Configure mx6 mmdc registers based on:
+ * - board-specific memory configuration
+ * - board-specific calibration data
+ * - ddr3 chip details
+ *
+ * The various calculations here are derived from the Freescale
+ * i.Mx6DQSDL DDR3 Script Aid spreadsheet (DOC-94917) designed to generate MMDC
+ * configuration registers based on memory system and memory chip parameters.
+ *
+ * The defaults here are those which were specified in the spreadsheet.
+ * For details on each register, refer to the IMX6DQRM and/or IMX6SDLRM
+ */
+#define MR(val, ba, cmd, cs1) \
+ ((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba)
+void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
+ const struct mx6_mmdc_calibration *c,
+ const struct mx6_ddr3_cfg *m)
+{
+ volatile struct mmdc_p_regs *mmdc0;
+ volatile struct mmdc_p_regs *mmdc1;
+ u32 reg;
+ u8 tcke, tcksrx, tcksre, txpdll, taofpd, taonpd, trrd;
+ u8 todtlon, taxpd, tanpd, tcwl, txp, tfaw, tcl;
+ u8 todt_idle_off = 0x4; /* from DDR3 Script Aid spreadsheet */
+ u16 trcd, trc, tras, twr, tmrd, trtp, trp, twtr, trfc, txs, txpr;
+ u16 CS0_END;
+ u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
+ int clkper; /* clock period in picoseconds */
+ int clock; /* clock freq in mHz */
+ int cs;
+
+ mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
+ mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
+
+ /* MX6D/MX6Q: 1066 MHz memory clock, clkper = 1.894ns = 1894ps */
+ if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) {
+ clock = 528;
+ tcwl = 4;
+ }
+ /* MX6S/MX6DL: 800 MHz memory clock, clkper = 2.5ns = 2500ps */
+ else {
+ clock = 400;
+ tcwl = 3;
+ }
+ clkper = (1000*1000)/clock; /* ps */
+ todtlon = tcwl;
+ taxpd = tcwl;
+ tanpd = tcwl;
+ tcwl = tcwl;
+
+ switch (m->density) {
+ case 1: /* 1Gb per chip */
+ trfc = DIV_ROUND_UP(110000, clkper) - 1;
+ txs = DIV_ROUND_UP(120000, clkper) - 1;
+ break;
+ case 2: /* 2Gb per chip */
+ trfc = DIV_ROUND_UP(160000, clkper) - 1;
+ txs = DIV_ROUND_UP(170000, clkper) - 1;
+ break;
+ case 4: /* 4Gb per chip */
+ trfc = DIV_ROUND_UP(260000, clkper) - 1;
+ txs = DIV_ROUND_UP(270000, clkper) - 1;
+ break;
+ case 8: /* 8Gb per chip */
+ trfc = DIV_ROUND_UP(350000, clkper) - 1;
+ txs = DIV_ROUND_UP(360000, clkper) - 1;
+ break;
+ default:
+ /* invalid density */
+ printf("invalid chip density\n");
+ hang();
+ break;
+ }
+ txpr = txs;
+
+ switch (m->mem_speed) {
+ case 800:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(40000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(50000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ }
+ break;
+ case 1066:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(37500, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(50000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ }
+ break;
+ case 1333:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(30000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(45000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ }
+ break;
+ case 1600:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 5000), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(30000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(40000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ }
+ break;
+ default:
+ printf("invalid memory speed\n");
+ hang();
+ break;
+ }
+ txpdll = DIV_ROUND_UP(MAX(10*clkper, 24000), clkper) - 1;
+ tcl = DIV_ROUND_UP(m->trcd, clkper/10) - 3;
+ tcksre = DIV_ROUND_UP(MAX(5*clkper, 10000), clkper);
+ tcksrx = tcksre;
+ taonpd = DIV_ROUND_UP(2000, clkper) - 1;
+ taofpd = taonpd;
+ trp = DIV_ROUND_UP(m->trcd, clkper/10) - 1;
+ trcd = trp;
+ trc = DIV_ROUND_UP(m->trcmin, clkper/10) - 1;
+ tras = DIV_ROUND_UP(m->trasmin, clkper/10) - 1;
+ twr = DIV_ROUND_UP(15000, clkper) - 1;
+ tmrd = DIV_ROUND_UP(MAX(12*clkper, 15000), clkper) - 1;
+ twtr = ROUND(MAX(4*clkper, 7500)/clkper, 1) - 1;
+ trtp = twtr;
+ CS0_END = ((4*i->cs_density) <= 120) ? (4*i->cs_density)+7 : 127;
+ debug("density:%d Gb (%d Gb per chip)\n", i->cs_density, m->density);
+ debug("clock: %dMHz (%d ps)\n", clock, clkper);
+ debug("memspd:%d\n", m->mem_speed);
+ debug("tcke=%d\n", tcke);
+ debug("tcksrx=%d\n", tcksrx);
+ debug("tcksre=%d\n", tcksre);
+ debug("taofpd=%d\n", taofpd);
+ debug("taonpd=%d\n", taonpd);
+ debug("todtlon=%d\n", todtlon);
+ debug("tanpd=%d\n", tanpd);
+ debug("taxpd=%d\n", taxpd);
+ debug("trfc=%d\n", trfc);
+ debug("txs=%d\n", txs);
+ debug("txp=%d\n", txp);
+ debug("txpdll=%d\n", txpdll);
+ debug("tfaw=%d\n", tfaw);
+ debug("tcl=%d\n", tcl);
+ debug("trcd=%d\n", trcd);
+ debug("trp=%d\n", trp);
+ debug("trc=%d\n", trc);
+ debug("tras=%d\n", tras);
+ debug("twr=%d\n", twr);
+ debug("tmrd=%d\n", tmrd);
+ debug("tcwl=%d\n", tcwl);
+ debug("tdllk=%d\n", tdllk);
+ debug("trtp=%d\n", trtp);
+ debug("twtr=%d\n", twtr);
+ debug("trrd=%d\n", trrd);
+ debug("txpr=%d\n", txpr);
+ debug("CS0_END=%d\n", CS0_END);
+ debug("ncs=%d\n", i->ncs);
+ debug("Rtt_wr=%d\n", i->rtt_wr);
+ debug("Rtt_nom=%d\n", i->rtt_nom);
+ debug("SRT=%d\n", m->SRT);
+ debug("tcl=%d\n", tcl);
+ debug("twr=%d\n", twr);
+
+ /* ZQ: enable both one-time & periodic (1ms) HW ZQ calibration */
+ mmdc0->mpzqhwctrl = (u32)0xa1390003;
+ if (i->dsize > 1)
+ mmdc1->mpzqhwctrl = (u32)0xa1390003;
+
+ /*
+ * board-specific configuration:
+ * These values are determined empirically and vary per board layout
+ * see:
+ * appnote, ddr3 spreadsheet
+ */
+ mmdc0->mpwldectrl0 = c->p0_mpwldectrl0;
+ mmdc0->mpwldectrl1 = c->p0_mpwldectrl1;
+ mmdc0->mpdgctrl0 = c->p0_mpdgctrl0;
+ mmdc0->mpdgctrl1 = c->p0_mpdgctrl1;
+ mmdc0->mprddlctl = c->p0_mprddlctl;
+ mmdc0->mpwrdlctl = c->p0_mpwrdlctl;
+ if (i->dsize > 1) {
+ mmdc1->mpwldectrl0 = c->p1_mpwldectrl0;
+ mmdc1->mpwldectrl1 = c->p1_mpwldectrl1;
+ mmdc1->mpdgctrl0 = c->p1_mpdgctrl0;
+ mmdc1->mpdgctrl1 = c->p1_mpdgctrl1;
+ mmdc1->mprddlctl = c->p1_mprddlctl;
+ mmdc1->mpwrdlctl = c->p1_mpwrdlctl;
+ }
+
+ /* Read data DQ Byte0-3 delay */
+ mmdc0->mprddqby0dl = (u32)0x33333333;
+ mmdc0->mprddqby1dl = (u32)0x33333333;
+ if (i->dsize > 0) {
+ mmdc0->mprddqby2dl = (u32)0x33333333;
+ mmdc0->mprddqby3dl = (u32)0x33333333;
+ }
+ if (i->dsize > 1) {
+ mmdc1->mprddqby0dl = (u32)0x33333333;
+ mmdc1->mprddqby1dl = (u32)0x33333333;
+ mmdc1->mprddqby2dl = (u32)0x33333333;
+ mmdc1->mprddqby3dl = (u32)0x33333333;
+ }
+
+ /* complete calibration by forced measurement */
+ mmdc0->mpmur0 = (u32)0x00000800;
+ if (i->dsize > 1)
+ mmdc1->mpmur0 = (u32)0x00000800;
+
+ /* MMDC init */
+ reg = (tcke << 16) | (tcksrx << 3) | tcksre;
+ mmdc0->mdpdc = reg;
+ reg = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) | (taxpd << 16) |
+ (todtlon << 12) | (todt_idle_off << 4);
+ mmdc0->mdotc = reg;
+
+ /* Timing configuration */
+ reg = (trfc << 24) | (txs << 16) | (txp << 13) | (txpdll << 9) |
+ (tfaw << 4) | tcl;
+ mmdc0->mdcfg0 = reg;
+ reg = (trcd << 29) | (trp << 26) | (trc << 21) | (tras << 16) |
+ (1 << 15) | /* trpa */
+ (twr << 9) | (tmrd << 5) | tcwl;
+ mmdc0->mdcfg1 = reg;
+ reg = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
+ mmdc0->mdcfg2 = reg;
+ reg = (i->cs1_mirror << 19) | (i->walat << 16) | (i->bi_on << 12) |
+ (i->mif3_mode << 9) | (i->ralat << 6);
+ mmdc0->mdmisc = reg;
+
+ /* configuration request */
+ mmdc0->mdscr = (u32)(1 << 15); /* config request */
+ mmdc0->mdrwd = (u32)0x000026d2;
+ reg = (txpr << 16) | (i->sde_to_rst << 8) | (i->rst_to_cke << 0);
+ mmdc0->mdor = reg;
+
+ /* addressing */
+ mmdc0->mdasp = CS0_END;
+ reg = (1 << 31) | /* SDE_0 */
+ ((i->ncs == 2) ? 1 : 0) << 30 | /* SDE_1 */
+ (m->rowaddr - 11) << 24 | /* ROW */
+ (m->coladdr - 9) << 20 | /* COL */
+ (1 << 19) | /* Burst Length = 8 for DDR3 */
+ (i->dsize << 16); /* DDR data bus size */
+ mmdc0->mdctl = reg;
+
+ /* Write Mode Registers to Init DDR3 devices */
+ for (cs = 0; cs < i->ncs; cs++) {
+ /* MR2 */
+ reg = (i->rtt_wr & 3) << 9 | (m->SRT & 1) << 7 |
+ ((tcwl - 3) & 3) << 3;
+ mmdc0->mdscr = (u32)MR(reg, 2, 3, cs);
+ /* MR3 */
+ mmdc0->mdscr = (u32)MR(0, 3, 3, cs);
+ /* MR1 */
+ reg = ((i->rtt_nom & 1) ? 1 : 0) << 2 |
+ ((i->rtt_nom & 2) ? 1 : 0) << 6;
+ mmdc0->mdscr = (u32)MR(reg, 1, 3, cs);
+ reg = ((tcl - 1) << 4) | /* CAS */
+ (1 << 8) | /* DLL Reset */
+ ((twr - 3) << 9); /* Write Recovery */
+ /* MR0 */
+ mmdc0->mdscr = (u32)MR(reg, 0, 3, cs);
+ /* ZQ calibration */
+ reg = (1 << 10);
+ mmdc0->mdscr = (u32)MR(reg, 0, 4, cs);
+ }
+
+ /* refresh control register */
+ reg = (1 << 14) | /* REF_SEL: Periodic refresh cycles of 32kHz */
+ (7 << 11); /* REFR: Refresh Rate - 8 refreshes */
+ mmdc0->mdref = reg;
+
+ /* MMDC Termination: rtt_nom:2 RZQ/2(120ohm), rtt_nom:1 RZQ/4(60ohm) */
+ reg = (i->rtt_nom == 2) ? 0x00011117 : 0x00022227;
+ mmdc0->mpodtctrl = reg;
+ if (i->dsize > 1)
+ mmdc1->mpodtctrl = reg;
+ /* Power down control */
+ reg = (tcke & 0x7) << 16 |
+ 5 << 12 | /* PWDT_1: 256 cycles */
+ 5 << 8 | /* PWDT_0: 256 cycles */
+ 1 << 6 | /* BOTH_CS_PD */
+ (tcksrx & 0x7) << 3 |
+ (tcksre & 0x7);
+ mmdc0->mdpdc = reg; /* SDCTL power down enabled */
+ mmdc0->mapsr = (u32)0x00011006; /* ADOPT power down enabled */
+ mmdc0->mdscr = (u32)0x00000000; /* init complete */
+}
diff --git a/arch/arm/include/asm/arch-mx6/mx6-ddr.h b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
index c2a31d2..d544d2e 100644
--- a/arch/arm/include/asm/arch-mx6/mx6-ddr.h
+++ b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
@@ -173,6 +173,78 @@ struct mx6sdl_iomux_grp_regs {
u32 res4;
u32 grp_b6ds;
};
+
+/* Device Information: Varies per DDR3 part number and speed grade */
+struct mx6_ddr3_cfg {
+ u16 mem_speed; /* ie 1600 for DDR3-1600 (800,1066,1333,1600) */
+ u8 density; /* chip density (Gb) (1,2,4,8) */
+ u8 width; /* bus width (bits) (4,8,16) */
+ u8 banks; /* number of banks */
+ u8 rowaddr; /* row address bits (11-16)*/
+ u8 coladdr; /* col address bits (9-12) */
+ u8 pagesz; /* page size (K) (1-2) */
+ u16 trcd; /* tRCD=tRP=CL (ns*100) */
+ u16 trcmin; /* tRC min (ns*100) */
+ u16 trasmin; /* tRAS min (ns*100) */
+ u8 SRT; /* self-refresh temperature: 0=normal, 1=extended */
+};
+
+/* System Information: Varies per board design, layout, and term choices */
+struct mx6_ddr_sysinfo {
+ u8 dsize; /* size of bus (in dwords: 0=16bit,1=32bit,2=64bit) */
+ u8 cs_density; /* density per chip select (Gb) */
+ u8 ncs; /* number chip selects used (1|2) */
+ char cs1_mirror;/* enable address mirror (0|1) */
+ char bi_on; /* Bank interleaving enable */
+ u8 rtt_nom; /* Rtt_Nom (DDR3_RTT_*) */
+ u8 rtt_wr; /* Rtt_Wr (DDR3_RTT_*) */
+ u8 ralat; /* Read Additional Latency (0-7) */
+ u8 walat; /* Write Additional Latency (0-3) */
+ u8 mif3_mode; /* Command prediction working mode */
+ u8 rst_to_cke; /* Time from SDE enable to CKE rise */
+ u8 sde_to_rst; /* Time from SDE enable until DDR reset# is high */
+};
+
+/*
+ * Board specific calibration:
+ * This includes write leveling calibration values as well as DQS gating
+ * and read/write delays. These values are board/layout/device specific.
+ * Freescale recommends using the i.MX6 DDR Stress Test Tool V1.0.2
+ * (DOC-96412) to determine these values over a range of boards and
+ * temperatures.
+ */
+struct mx6_mmdc_calibration {
+ /* write leveling calibration */
+ u32 p0_mpwldectrl0;
+ u32 p0_mpwldectrl1;
+ u32 p1_mpwldectrl0;
+ u32 p1_mpwldectrl1;
+ /* read DQS gating */
+ u32 p0_mpdgctrl0;
+ u32 p0_mpdgctrl1;
+ u32 p1_mpdgctrl0;
+ u32 p1_mpdgctrl1;
+ /* read delay */
+ u32 p0_mprddlctl;
+ u32 p1_mprddlctl;
+ /* write delay */
+ u32 p0_mpwrdlctl;
+ u32 p1_mpwrdlctl;
+};
+
+/* configure iomux (pinctl/padctl) */
+void mx6dq_dram_iocfg(unsigned width,
+ const struct mx6dq_iomux_ddr_regs *,
+ const struct mx6dq_iomux_grp_regs *);
+void mx6sdl_dram_iocfg(unsigned width,
+ const struct mx6sdl_iomux_ddr_regs *,
+ const struct mx6sdl_iomux_grp_regs *);
+
+/* configure mx6 mmdc registers */
+void mx6_dram_cfg(const struct mx6_ddr_sysinfo *,
+ const struct mx6_mmdc_calibration *,
+ const struct mx6_ddr3_cfg *);
+
#endif /* CONFIG_SPL_BUILD */
#define MX6_MMDC_P0_MDCTL 0x021b0000
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 08/11] imx: iomux: add macros to setup iomux for multiple SoC types
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (6 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 07/11] mx6: add mmdc configuration for MX6Q/MX6DL Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 09/11] imx: ventana: split read_eeprom into standalone file Tim Harvey
` (3 subsequent siblings)
11 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Allow imx_iomux_v3_setup_multiple_pads to take a multi-cpu pad_list
and add macros for declaring the pad_list that take into account the
SoC types supported using CONFIG_MX6QDL (supports both the MX6Q and MX6DL
iomux).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- remove commit msg 2nd paragrap about prior approaches
- re-work to avoid needing to add a new function by making
imx_iomux_v3_setup_multiple_pads more intelligent and adding macros
that depend on SoC type support
v2:
- moved macros for declaring and using structs for array variant
- removed non-related whitespace cleanup
---
arch/arm/imx-common/iomux-v3.c | 16 ++++++++++++++--
arch/arm/include/asm/imx-common/iomux-v3.h | 25 +++++++++++++++++++++++++
2 files changed, 39 insertions(+), 2 deletions(-)
diff --git a/arch/arm/imx-common/iomux-v3.c b/arch/arm/imx-common/iomux-v3.c
index b59b802..9bd8dfb 100644
--- a/arch/arm/imx-common/iomux-v3.c
+++ b/arch/arm/imx-common/iomux-v3.c
@@ -11,6 +11,7 @@
#include <common.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
#include <asm/imx-common/iomux-v3.h>
static void *base = (void *)IOMUXC_BASE_ADDR;
@@ -46,12 +47,23 @@ void imx_iomux_v3_setup_pad(iomux_v3_cfg_t pad)
#endif
}
+/* configures a list of pads within declared with IOMUX_PADS macro */
void imx_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t const *pad_list,
unsigned count)
{
iomux_v3_cfg_t const *p = pad_list;
+ int stride;
int i;
- for (i = 0; i < count; i++)
- imx_iomux_v3_setup_pad(*p++);
+#if defined(CONFIG_MX6QDL)
+ stride = 2;
+ if (!is_cpu_type(MXC_CPU_MX6Q) && !is_cpu_type(MXC_CPU_MX6D))
+ p += 1;
+#else
+ stride = 1;
+#endif
+ for (i = 0; i < count; i++) {
+ imx_iomux_v3_setup_pad(*p);
+ p += stride;
+ }
}
diff --git a/arch/arm/include/asm/imx-common/iomux-v3.h b/arch/arm/include/asm/imx-common/iomux-v3.h
index dec11a1..3b0759a 100644
--- a/arch/arm/include/asm/imx-common/iomux-v3.h
+++ b/arch/arm/include/asm/imx-common/iomux-v3.h
@@ -170,4 +170,29 @@ void imx_iomux_v3_setup_pad(iomux_v3_cfg_t pad);
void imx_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t const *pad_list,
unsigned count);
+/* macros for declaring and using pinmux array */
+#if defined(CONFIG_MX6QDL)
+#define IOMUX_PADS(x) (MX6Q_##x), (MX6DL_##x)
+#define SETUP_IOMUX_PAD(def) \
+if (is_cpu_type(MXC_CPU_MX6Q)) { \
+ imx_iomux_v3_setup_pad(MX6Q_##def); \
+} else { \
+ imx_iomux_v3_setup_pad(MX6DL_##def); \
+}
+#define SETUP_IOMUX_PADS(x) \
+ imx_iomux_v3_setup_multiple_pads(x, ARRAY_SIZE(x)/2)
+#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
+#define IOMUX_PADS(x) MX6Q_##x
+#define SETUP_IOMUX_PAD(def) \
+ imx_iomux_v3_setup_pad(MX6Q_##def);
+#define SETUP_IOMUX_PADS(x) \
+ imx_iomux_v3_setup_multiple_pads(x, ARRAY_SIZE(x))
+#else
+#define IOMUX_PADS(x) MX6DL_##x
+#define SETUP_IOMUX_PAD(def) \
+ imx_iomux_v3_setup_pad(MX6DL_##def);
+#define SETUP_IOMUX_PADS(x) \
+ imx_iomux_v3_setup_multiple_pads(x, ARRAY_SIZE(x))
+#endif
+
#endif /* __MACH_IOMUX_V3_H__*/
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 09/11] imx: ventana: split read_eeprom into standalone file
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (7 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 08/11] imx: iomux: add macros to setup iomux for multiple SoC types Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 10/11] imx: ventana: auto-configure for IMX6Q vs IMX6DL Tim Harvey
` (2 subsequent siblings)
11 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Split the read_eeprom function out so that it can be shared (ie with SPL)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- no changes
v2:
- new patch in series
---
board/gateworks/gw_ventana/Makefile | 2 +-
board/gateworks/gw_ventana/eeprom.c | 89 +++++++++++++++++++++++++++++
board/gateworks/gw_ventana/gw_ventana.c | 89 +----------------------------
board/gateworks/gw_ventana/ventana_eeprom.h | 11 ++++
4 files changed, 102 insertions(+), 89 deletions(-)
create mode 100644 board/gateworks/gw_ventana/eeprom.c
diff --git a/board/gateworks/gw_ventana/Makefile b/board/gateworks/gw_ventana/Makefile
index e8dab89..03bd1fd 100644
--- a/board/gateworks/gw_ventana/Makefile
+++ b/board/gateworks/gw_ventana/Makefile
@@ -6,5 +6,5 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y := gw_ventana.o gsc.o
+obj-y := gw_ventana.o gsc.o eeprom.o
diff --git a/board/gateworks/gw_ventana/eeprom.c b/board/gateworks/gw_ventana/eeprom.c
new file mode 100644
index 0000000..e90186e
--- /dev/null
+++ b/board/gateworks/gw_ventana/eeprom.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include "gsc.h"
+#include "ventana_eeprom.h"
+
+/* read ventana EEPROM, check for validity, and return baseboard type */
+int
+read_eeprom(int bus, struct ventana_board_info *info)
+{
+ int i;
+ int chksum;
+ char baseboard;
+ int type;
+ unsigned char *buf = (unsigned char *)info;
+
+ memset(info, 0, sizeof(*info));
+
+ /*
+ * On a board with a missing/depleted backup battery for GSC, the
+ * board may be ready to probe the GSC before its firmware is
+ * running. We will wait here indefinately for the GSC/EEPROM.
+ */
+ while (1) {
+ if (0 == i2c_set_bus_num(bus) &&
+ 0 == i2c_probe(GSC_EEPROM_ADDR))
+ break;
+ mdelay(1);
+ }
+
+ /* read eeprom config section */
+ if (gsc_i2c_read(GSC_EEPROM_ADDR, 0x00, 1, buf, sizeof(*info))) {
+ puts("EEPROM: Failed to read EEPROM\n");
+ info->model[0] = 0;
+ return GW_UNKNOWN;
+ }
+
+ /* sanity checks */
+ if (info->model[0] != 'G' || info->model[1] != 'W') {
+ puts("EEPROM: Invalid Model in EEPROM\n");
+ info->model[0] = 0;
+ return GW_UNKNOWN;
+ }
+
+ /* validate checksum */
+ for (chksum = 0, i = 0; i < sizeof(*info)-2; i++)
+ chksum += buf[i];
+ if ((info->chksum[0] != chksum>>8) ||
+ (info->chksum[1] != (chksum&0xff))) {
+ puts("EEPROM: Failed EEPROM checksum\n");
+ info->model[0] = 0;
+ return GW_UNKNOWN;
+ }
+
+ /* original GW5400-A prototype */
+ baseboard = info->model[3];
+ if (strncasecmp((const char *)info->model, "GW5400-A", 8) == 0)
+ baseboard = '0';
+
+ switch (baseboard) {
+ case '0': /* original GW5400-A prototype */
+ type = GW54proto;
+ break;
+ case '1':
+ type = GW51xx;
+ break;
+ case '2':
+ type = GW52xx;
+ break;
+ case '3':
+ type = GW53xx;
+ break;
+ case '4':
+ type = GW54xx;
+ break;
+ default:
+ printf("EEPROM: Unknown model in EEPROM: %s\n", info->model);
+ type = GW_UNKNOWN;
+ break;
+ }
+ return type;
+}
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index 2113740..3b6bc01 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -81,15 +81,6 @@ DECLARE_GLOBAL_DATA_PTR;
*/
static struct ventana_board_info ventana_info;
-enum {
- GW54proto, /* original GW5400-A prototype */
- GW51xx,
- GW52xx,
- GW53xx,
- GW54xx,
- GW_UNKNOWN,
-};
-
int board_type;
/* UART1: Function varies per baseboard */
@@ -368,84 +359,6 @@ int board_eth_init(bd_t *bis)
return 0;
}
-/* read ventana EEPROM, check for validity, and return baseboard type */
-static int
-read_eeprom(void)
-{
- int i;
- int chksum;
- char baseboard;
- int type;
- struct ventana_board_info *info = &ventana_info;
- unsigned char *buf = (unsigned char *)&ventana_info;
-
- memset(info, 0, sizeof(ventana_info));
-
- /*
- * On a board with a missing/depleted backup battery for GSC, the
- * board may be ready to probe the GSC before its firmware is
- * running. We will wait here indefinately for the GSC/EEPROM.
- */
- while (1) {
- if (0 == i2c_set_bus_num(I2C_GSC) &&
- 0 == i2c_probe(GSC_EEPROM_ADDR))
- break;
- mdelay(1);
- }
-
- /* read eeprom config section */
- if (gsc_i2c_read(GSC_EEPROM_ADDR, 0x00, 1, buf, sizeof(ventana_info))) {
- puts("EEPROM: Failed to read EEPROM\n");
- info->model[0] = 0;
- return GW_UNKNOWN;
- }
-
- /* sanity checks */
- if (info->model[0] != 'G' || info->model[1] != 'W') {
- puts("EEPROM: Invalid Model in EEPROM\n");
- info->model[0] = 0;
- return GW_UNKNOWN;
- }
-
- /* validate checksum */
- for (chksum = 0, i = 0; i < sizeof(*info)-2; i++)
- chksum += buf[i];
- if ((info->chksum[0] != chksum>>8) ||
- (info->chksum[1] != (chksum&0xff))) {
- puts("EEPROM: Failed EEPROM checksum\n");
- info->model[0] = 0;
- return GW_UNKNOWN;
- }
-
- /* original GW5400-A prototype */
- baseboard = info->model[3];
- if (strncasecmp((const char *)info->model, "GW5400-A", 8) == 0)
- baseboard = '0';
-
- switch (baseboard) {
- case '0': /* original GW5400-A prototype */
- type = GW54proto;
- break;
- case '1':
- type = GW51xx;
- break;
- case '2':
- type = GW52xx;
- break;
- case '3':
- type = GW53xx;
- break;
- case '4':
- type = GW54xx;
- break;
- default:
- printf("EEPROM: Unknown model in EEPROM: %s\n", info->model);
- type = GW_UNKNOWN;
- break;
- }
- return type;
-}
-
/*
* Baseboard specific GPIO
*/
@@ -924,7 +837,7 @@ int board_init(void)
setup_sata();
#endif
/* read Gateworks EEPROM into global struct (used later) */
- board_type = read_eeprom();
+ board_type = read_eeprom(I2C_GSC, &ventana_info);
/* board-specifc GPIO iomux */
if (board_type < GW_UNKNOWN) {
diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h
index 434b604..5b065be 100644
--- a/board/gateworks/gw_ventana/ventana_eeprom.h
+++ b/board/gateworks/gw_ventana/ventana_eeprom.h
@@ -103,4 +103,15 @@ enum {
EECONFIG_RES15,
};
+enum {
+ GW54proto, /* original GW5400-A prototype */
+ GW51xx,
+ GW52xx,
+ GW53xx,
+ GW54xx,
+ GW_UNKNOWN,
+};
+
+int read_eeprom(int bus, struct ventana_board_info *);
+
#endif
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 10/11] imx: ventana: auto-configure for IMX6Q vs IMX6DL
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (8 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 09/11] imx: ventana: split read_eeprom into standalone file Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL Tim Harvey
2014-05-22 6:14 ` [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
11 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
use the new iomux function and a macros to create a multi-dimensional array
of iomux values without duplicating the defintions.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- replace use of imx_iomux_v3_setup_multiple_pads_array with
imx_iomux_v3_setup_multiple_pads
v2:
- use macros that have been moved to iomux-v3.h
---
board/gateworks/gw_ventana/gw_ventana.c | 492 ++++++++++++++++++++------------
1 file changed, 310 insertions(+), 182 deletions(-)
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index 3b6bc01..4ae458f 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -85,109 +85,149 @@ int board_type;
/* UART1: Function varies per baseboard */
iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
/* UART2: Serial Console */
iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IOMUX_PADS(PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/* I2C1: GSC */
-struct i2c_pads_info i2c_pad_info0 = {
+struct i2c_pads_info mx6q_i2c_pad_info0 = {
.scl = {
- .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_EIM_D21__GPIO3_IO21 | PC,
+ .i2c_mode = MX6Q_PAD_EIM_D21__I2C1_SCL | PC,
+ .gpio_mode = MX6Q_PAD_EIM_D21__GPIO3_IO21 | PC,
.gp = IMX_GPIO_NR(3, 21)
},
.sda = {
- .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_EIM_D28__GPIO3_IO28 | PC,
+ .i2c_mode = MX6Q_PAD_EIM_D28__I2C1_SDA | PC,
+ .gpio_mode = MX6Q_PAD_EIM_D28__GPIO3_IO28 | PC,
+ .gp = IMX_GPIO_NR(3, 28)
+ }
+};
+struct i2c_pads_info mx6dl_i2c_pad_info0 = {
+ .scl = {
+ .i2c_mode = MX6DL_PAD_EIM_D21__I2C1_SCL | PC,
+ .gpio_mode = MX6DL_PAD_EIM_D21__GPIO3_IO21 | PC,
+ .gp = IMX_GPIO_NR(3, 21)
+ },
+ .sda = {
+ .i2c_mode = MX6DL_PAD_EIM_D28__I2C1_SDA | PC,
+ .gpio_mode = MX6DL_PAD_EIM_D28__GPIO3_IO28 | PC,
.gp = IMX_GPIO_NR(3, 28)
}
};
/* I2C2: PMIC/PCIe Switch/PCIe Clock/Mezz */
-struct i2c_pads_info i2c_pad_info1 = {
+struct i2c_pads_info mx6q_i2c_pad_info1 = {
.scl = {
- .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC,
+ .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
+ .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
.gp = IMX_GPIO_NR(4, 12)
},
.sda = {
- .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+ .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
+ .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+ .gp = IMX_GPIO_NR(4, 13)
+ }
+};
+struct i2c_pads_info mx6dl_i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC,
+ .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC,
+ .gp = IMX_GPIO_NR(4, 12)
+ },
+ .sda = {
+ .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC,
+ .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC,
.gp = IMX_GPIO_NR(4, 13)
}
};
/* I2C3: Misc/Expansion */
-struct i2c_pads_info i2c_pad_info2 = {
+struct i2c_pads_info mx6q_i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6Q_PAD_GPIO_3__I2C3_SCL | PC,
+ .gpio_mode = MX6Q_PAD_GPIO_3__GPIO1_IO03 | PC,
+ .gp = IMX_GPIO_NR(1, 3)
+ },
+ .sda = {
+ .i2c_mode = MX6Q_PAD_GPIO_6__I2C3_SDA | PC,
+ .gpio_mode = MX6Q_PAD_GPIO_6__GPIO1_IO06 | PC,
+ .gp = IMX_GPIO_NR(1, 6)
+ }
+};
+struct i2c_pads_info mx6dl_i2c_pad_info2 = {
.scl = {
- .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC,
+ .i2c_mode = MX6DL_PAD_GPIO_3__I2C3_SCL | PC,
+ .gpio_mode = MX6DL_PAD_GPIO_3__GPIO1_IO03 | PC,
.gp = IMX_GPIO_NR(1, 3)
},
.sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
+ .i2c_mode = MX6DL_PAD_GPIO_6__I2C3_SDA | PC,
+ .gpio_mode = MX6DL_PAD_GPIO_6__GPIO1_IO06 | PC,
.gp = IMX_GPIO_NR(1, 6)
}
};
/* MMC */
iomux_v3_cfg_t const usdhc3_pads[] = {
- MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ /* CD */
+ IOMUX_PADS(PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
/* ENET */
iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
+ MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |
+ MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
+ MUX_PAD_CTRL(ENET_PAD_CTRL)),
/* PHY nRST */
- MX6_PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
/* NAND */
iomux_v3_cfg_t const nfc_pads[] = {
- MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
#ifdef CONFIG_CMD_NAND
@@ -196,7 +236,7 @@ static void setup_gpmi_nand(void)
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* config gpmi nand iomux */
- imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
+ SETUP_IOMUX_PADS(nfc_pads);
/* config gpmi and bch clock to 100 MHz */
clrsetbits_le32(&mxc_ccm->cs2cdr,
@@ -222,7 +262,7 @@ static void setup_gpmi_nand(void)
static void setup_iomux_enet(void)
{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+ SETUP_IOMUX_PADS(enet_pads);
/* toggle PHY_RST# */
gpio_direction_output(GP_PHY_RST, 0);
@@ -232,35 +272,36 @@ static void setup_iomux_enet(void)
static void setup_iomux_uart(void)
{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+ SETUP_IOMUX_PADS(uart1_pads);
+ SETUP_IOMUX_PADS(uart2_pads);
}
#ifdef CONFIG_USB_EHCI_MX6
iomux_v3_cfg_t const usb_pads[] = {
- MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(DIO_PAD_CTRL),
- MX6_PAD_KEY_COL4__USB_OTG_OC | MUX_PAD_CTRL(DIO_PAD_CTRL),
- MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(DIO_PAD_CTRL), /* OTG PWR */
+ IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(DIO_PAD_CTRL)),
+ IOMUX_PADS(PAD_KEY_COL4__USB_OTG_OC | MUX_PAD_CTRL(DIO_PAD_CTRL)),
+ /* OTG PWR */
+ IOMUX_PADS(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(DIO_PAD_CTRL)),
};
int board_ehci_hcd_init(int port)
{
struct ventana_board_info *info = &ventana_info;
- imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads));
+ SETUP_IOMUX_PADS(usb_pads);
/* Reset USB HUB (present on GW54xx/GW53xx) */
switch (info->model[3]) {
case '3': /* GW53xx */
- imx_iomux_v3_setup_pad(MX6_PAD_GPIO_9__GPIO1_IO09|
- MUX_PAD_CTRL(NO_PAD_CTRL));
+ SETUP_IOMUX_PAD(PAD_GPIO_9__GPIO1_IO09 |
+ MUX_PAD_CTRL(NO_PAD_CTRL));
gpio_direction_output(IMX_GPIO_NR(1, 9), 0);
mdelay(2);
gpio_set_value(IMX_GPIO_NR(1, 9), 1);
break;
case '4': /* GW54xx */
- imx_iomux_v3_setup_pad(MX6_PAD_SD1_DAT0__GPIO1_IO16 |
- MUX_PAD_CTRL(NO_PAD_CTRL));
+ SETUP_IOMUX_PAD(PAD_SD1_DAT0__GPIO1_IO16 |
+ MUX_PAD_CTRL(NO_PAD_CTRL));
gpio_direction_output(IMX_GPIO_NR(1, 16), 0);
mdelay(2);
gpio_set_value(IMX_GPIO_NR(1, 16), 1);
@@ -292,7 +333,7 @@ int board_mmc_getcd(struct mmc *mmc)
int board_mmc_init(bd_t *bis)
{
/* Only one USDHC controller on Ventana */
- imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ SETUP_IOMUX_PADS(usdhc3_pads);
usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
usdhc_cfg.max_bus_width = 4;
@@ -303,17 +344,16 @@ int board_mmc_init(bd_t *bis)
#ifdef CONFIG_MXC_SPI
iomux_v3_cfg_t const ecspi1_pads[] = {
/* SS1 */
- MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
};
static void setup_spi(void)
{
gpio_direction_output(CONFIG_SF_DEFAULT_CS, 1);
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
- ARRAY_SIZE(ecspi1_pads));
+ SETUP_IOMUX_PADS(ecspi1_pads);
}
#endif
@@ -366,118 +406,118 @@ int board_eth_init(bd_t *bis)
/* common to add baseboards */
static iomux_v3_cfg_t const gw_gpio_pads[] = {
/* MSATA_EN */
- MX6_PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* RS232_EN# */
- MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
/* prototype */
static iomux_v3_cfg_t const gwproto_gpio_pads[] = {
/* PANLEDG# */
- MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PANLEDR# */
- MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* LOCLED# */
- MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* RS485_EN */
- MX6_PAD_SD3_DAT4__GPIO7_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_SD3_DAT4__GPIO7_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_PWREN# */
- MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_IRQ# */
- MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* VID_EN */
- MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* DIOI2C_DIS# */
- MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCICK_SSON */
- MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCI_RST# */
- MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const gw51xx_gpio_pads[] = {
/* PANLEDG# */
- MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PANLEDR# */
- MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_PWREN# */
- MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_IRQ# */
- MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* GPS_SHDN */
- MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* VID_PWR */
- MX6_PAD_CSI0_DATA_EN__GPIO5_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCI_RST# */
- MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const gw52xx_gpio_pads[] = {
/* PANLEDG# */
- MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PANLEDR# */
- MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_PWREN# */
- MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_IRQ# */
- MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* MX6_LOCLED# */
- MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* GPS_SHDN */
- MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* USBOTG_SEL */
- MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* VID_PWR */
- MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCI_RST# */
- MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const gw53xx_gpio_pads[] = {
/* PANLEDG# */
- MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PANLEDR# */
- MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_PWREN# */
- MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_IRQ# */
- MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* MX6_LOCLED# */
- MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* GPS_SHDN */
- MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* VID_EN */
- MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCI_RST# */
- MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const gw54xx_gpio_pads[] = {
/* PANLEDG# */
- MX6_PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PANLEDR# */
- MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* MX6_LOCLED# */
- MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* MIPI_DIO */
- MX6_PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_SD1_DAT3__GPIO1_IO21 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* RS485_EN */
- MX6_PAD_EIM_D24__GPIO3_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D24__GPIO3_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_PWREN# */
- MX6_PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* IOEXP_IRQ# */
- MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* DIOI2C_DIS# */
- MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* DIOI2C_DIS# */
- MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCICK_SSON */
- MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* PCI_RST# */
- MX6_PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
/*
@@ -485,9 +525,9 @@ static iomux_v3_cfg_t const gw54xx_gpio_pads[] = {
* be pinmuxed as a GPIO or in some cases a PWM
*/
struct dio_cfg {
- iomux_v3_cfg_t gpio_padmux;
+ iomux_v3_cfg_t gpio_padmux[2];
unsigned gpio_param;
- iomux_v3_cfg_t pwm_padmux;
+ iomux_v3_cfg_t pwm_padmux[2];
unsigned pwm_param;
};
@@ -514,16 +554,32 @@ struct ventana gpio_cfg[] = {
/* GW5400proto */
{
.gpio_pads = gw54xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw54xx_gpio_pads),
+ .num_pads = ARRAY_SIZE(gw54xx_gpio_pads)/2,
.dio_cfg = {
- { MX6_PAD_GPIO_9__GPIO1_IO09, IMX_GPIO_NR(1, 9),
- MX6_PAD_GPIO_9__PWM1_OUT, 1 },
- { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
- MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
- { MX6_PAD_SD4_DAT1__GPIO2_IO09, IMX_GPIO_NR(2, 9),
- MX6_PAD_SD4_DAT1__PWM3_OUT, 3 },
- { MX6_PAD_SD4_DAT2__GPIO2_IO10, IMX_GPIO_NR(2, 10),
- MX6_PAD_SD4_DAT2__PWM4_OUT, 4 },
+ {
+ { IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09) },
+ IMX_GPIO_NR(1, 9),
+ { IOMUX_PADS(PAD_GPIO_9__PWM1_OUT) },
+ 1
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD4_DAT1__GPIO2_IO09) },
+ IMX_GPIO_NR(2, 9),
+ { IOMUX_PADS(PAD_SD4_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ { IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10) },
+ IMX_GPIO_NR(2, 10),
+ { IOMUX_PADS(PAD_SD4_DAT2__PWM4_OUT) },
+ 4
+ },
},
.leds = {
IMX_GPIO_NR(4, 6),
@@ -541,16 +597,32 @@ struct ventana gpio_cfg[] = {
/* GW51xx */
{
.gpio_pads = gw51xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw51xx_gpio_pads),
+ .num_pads = ARRAY_SIZE(gw51xx_gpio_pads)/2,
.dio_cfg = {
- { MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16),
- 0, 0 },
- { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
- MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
- { MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17),
- MX6_PAD_SD1_DAT1__PWM3_OUT, 3 },
- { MX6_PAD_SD1_CMD__GPIO1_IO18, IMX_GPIO_NR(1, 18),
- MX6_PAD_SD1_CMD__PWM4_OUT, 4 },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+ IMX_GPIO_NR(1, 16),
+ { 0, 0 },
+ 0
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+ IMX_GPIO_NR(1, 17),
+ { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
+ IMX_GPIO_NR(1, 18),
+ { IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
+ 4
+ },
},
.leds = {
IMX_GPIO_NR(4, 6),
@@ -566,16 +638,32 @@ struct ventana gpio_cfg[] = {
/* GW52xx */
{
.gpio_pads = gw52xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw52xx_gpio_pads),
+ .num_pads = ARRAY_SIZE(gw52xx_gpio_pads)/2,
.dio_cfg = {
- { MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16),
- 0, 0 },
- { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
- MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
- { MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17),
- MX6_PAD_SD1_DAT1__PWM3_OUT, 3 },
- { MX6_PAD_SD1_CLK__GPIO1_IO20, IMX_GPIO_NR(1, 20),
- 0, 0 },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+ IMX_GPIO_NR(1, 16),
+ { 0, 0 },
+ 0
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+ IMX_GPIO_NR(1, 17),
+ { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+ IMX_GPIO_NR(1, 20),
+ { 0, 0 },
+ 0
+ },
},
.leds = {
IMX_GPIO_NR(4, 6),
@@ -593,16 +681,32 @@ struct ventana gpio_cfg[] = {
/* GW53xx */
{
.gpio_pads = gw53xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw53xx_gpio_pads),
+ .num_pads = ARRAY_SIZE(gw53xx_gpio_pads)/2,
.dio_cfg = {
- { MX6_PAD_SD1_DAT0__GPIO1_IO16, IMX_GPIO_NR(1, 16),
- 0, 0 },
- { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
- MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
- { MX6_PAD_SD1_DAT1__GPIO1_IO17, IMX_GPIO_NR(1, 17),
- MX6_PAD_SD1_DAT1__PWM3_OUT, 3 },
- { MX6_PAD_SD1_CLK__GPIO1_IO20, IMX_GPIO_NR(1, 20),
- 0, 0 },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
+ IMX_GPIO_NR(1, 16),
+ { 0, 0 },
+ 0
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
+ IMX_GPIO_NR(1, 17),
+ { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ {IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
+ IMX_GPIO_NR(1, 20),
+ { 0, 0 },
+ 0
+ },
},
.leds = {
IMX_GPIO_NR(4, 6),
@@ -619,16 +723,32 @@ struct ventana gpio_cfg[] = {
/* GW54xx */
{
.gpio_pads = gw54xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw54xx_gpio_pads),
+ .num_pads = ARRAY_SIZE(gw54xx_gpio_pads)/2,
.dio_cfg = {
- { MX6_PAD_GPIO_9__GPIO1_IO09, IMX_GPIO_NR(1, 9),
- MX6_PAD_GPIO_9__PWM1_OUT, 1 },
- { MX6_PAD_SD1_DAT2__GPIO1_IO19, IMX_GPIO_NR(1, 19),
- MX6_PAD_SD1_DAT2__PWM2_OUT, 2 },
- { MX6_PAD_SD4_DAT1__GPIO2_IO09, IMX_GPIO_NR(2, 9),
- MX6_PAD_SD4_DAT1__PWM3_OUT, 3 },
- { MX6_PAD_SD4_DAT2__GPIO2_IO10, IMX_GPIO_NR(2, 10),
- MX6_PAD_SD4_DAT2__PWM4_OUT, 4 },
+ {
+ { IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09) },
+ IMX_GPIO_NR(1, 9),
+ { IOMUX_PADS(PAD_GPIO_9__PWM1_OUT) },
+ 1
+ },
+ {
+ { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
+ IMX_GPIO_NR(1, 19),
+ { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
+ 2
+ },
+ {
+ { IOMUX_PADS(PAD_SD4_DAT1__GPIO2_IO09) },
+ IMX_GPIO_NR(2, 9),
+ { IOMUX_PADS(PAD_SD4_DAT1__PWM3_OUT) },
+ 3
+ },
+ {
+ { IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10) },
+ IMX_GPIO_NR(2, 10),
+ { IOMUX_PADS(PAD_SD4_DAT2__PWM4_OUT) },
+ 4
+ },
},
.leds = {
IMX_GPIO_NR(4, 6),
@@ -718,6 +838,7 @@ static void setup_board_gpio(int board)
for (i = 0; i < 4; i++) {
struct dio_cfg *cfg = &gpio_cfg[board].dio_cfg[i];
unsigned ctrl = DIO_PAD_CTRL;
+ unsigned cputype = is_cpu_type(MXC_CPU_MX6Q) ? 0 : 1;
sprintf(arg, "dio%d", i);
if (!hwconfig(arg))
@@ -732,14 +853,14 @@ static void setup_board_gpio(int board)
cfg->gpio_param%32,
cfg->gpio_param);
}
- imx_iomux_v3_setup_pad(cfg->gpio_padmux |
+ imx_iomux_v3_setup_pad(cfg->gpio_padmux[cputype] |
MUX_PAD_CTRL(ctrl));
gpio_direction_input(cfg->gpio_param);
} else if (hwconfig_subarg_cmp("dio2", "mode", "pwm") &&
cfg->pwm_padmux) {
if (!quiet)
printf("DIO%d: pwm%d\n", i, cfg->pwm_param);
- imx_iomux_v3_setup_pad(cfg->pwm_padmux |
+ imx_iomux_v3_setup_pad(cfg->pwm_padmux[cputype] |
MUX_PAD_CTRL(ctrl));
}
}
@@ -759,9 +880,10 @@ static void setup_board_gpio(int board)
int imx6_pcie_toggle_reset(void)
{
if (board_type < GW_UNKNOWN) {
- gpio_direction_output(gpio_cfg[board_type].pcie_rst, 0);
+ uint pin = gpio_cfg[board_type].pcie_rst;
+ gpio_direction_output(pin, 0);
mdelay(50);
- gpio_direction_output(gpio_cfg[board_type].pcie_rst, 1);
+ gpio_direction_output(pin, 1);
}
return 0;
}
@@ -807,7 +929,6 @@ int dram_init(void)
{
gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
CONFIG_DDR_MB*1024*1024);
-
return 0;
}
@@ -829,9 +950,15 @@ int board_init(void)
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+ if (is_cpu_type(MXC_CPU_MX6Q)) {
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info0);
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info2);
+ } else {
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info0);
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
+ setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info2);
+ }
#ifdef CONFIG_CMD_SATA
setup_sata();
@@ -840,11 +967,12 @@ int board_init(void)
board_type = read_eeprom(I2C_GSC, &ventana_info);
/* board-specifc GPIO iomux */
+ SETUP_IOMUX_PADS(gw_gpio_pads);
if (board_type < GW_UNKNOWN) {
- imx_iomux_v3_setup_multiple_pads(gw_gpio_pads,
- ARRAY_SIZE(gw_gpio_pads));
- imx_iomux_v3_setup_multiple_pads(gpio_cfg[board_type].gpio_pads,
- gpio_cfg[board_type].num_pads);
+ iomux_v3_cfg_t const *p = gpio_cfg[board_type].gpio_pads;
+ int count = gpio_cfg[board_type].num_pads;
+
+ imx_iomux_v3_setup_multiple_pads(p, count);
}
return 0;
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (9 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 10/11] imx: ventana: auto-configure for IMX6Q vs IMX6DL Tim Harvey
@ 2014-05-08 5:16 ` Tim Harvey
2014-05-29 7:02 ` Stefano Babic
2014-05-22 6:14 ` [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
11 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-08 5:16 UTC (permalink / raw)
To: u-boot
Switch to an SPL image. The SPL for Ventana does the following:
- setup i2c and read the factory programmed EEPROM to obtain DRAM config
and model for board-specific calibration data
- configure DRAM per CPU/size/layout/devices/calibration
- load u-boot.img from NAND and jump to it
This allows for a single SPL+u-boot.img to replace the previous multiple boa
configurations.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v3:
- re-ordered calls in board_init_f
v2:
- remove missing/unnecessary include
- revert mtdparts change
- use imx_ddr_size() which uses MMDC configuration to determine mem size
explicitly
- add support for MX6SOLO and MX6DUAL
- set CS0_END for 4GB so get_ram_size() works
- updated DDR3 calibration values for ventana boards
- fixed build issue - only compile spl if doing spl build
- fixed line length issue in README
- remove CONFIG_SPL* conditions and conditionally compile instead
- removed prints for CPU type and DRAM size/width - uboot will print these
later
- removed unused gw_ventana_spl.cfg
- use common read_eeprom function
- added MMC support to SPL
---
board/gateworks/gw_ventana/Makefile | 1 +
board/gateworks/gw_ventana/README | 92 +++---
board/gateworks/gw_ventana/gw_ventana.c | 10 +-
board/gateworks/gw_ventana/gw_ventana.cfg | 15 -
board/gateworks/gw_ventana/gw_ventana_spl.c | 419 ++++++++++++++++++++++++++++
boards.cfg | 6 +-
include/configs/gw_ventana.h | 11 +
7 files changed, 498 insertions(+), 56 deletions(-)
create mode 100644 board/gateworks/gw_ventana/gw_ventana_spl.c
diff --git a/board/gateworks/gw_ventana/Makefile b/board/gateworks/gw_ventana/Makefile
index 03bd1fd..33a1788 100644
--- a/board/gateworks/gw_ventana/Makefile
+++ b/board/gateworks/gw_ventana/Makefile
@@ -7,4 +7,5 @@
#
obj-y := gw_ventana.o gsc.o eeprom.o
+obj-$(CONFIG_SPL_BUILD) += gw_ventana_spl.o
diff --git a/board/gateworks/gw_ventana/README b/board/gateworks/gw_ventana/README
index 9e697d6..888657c 100644
--- a/board/gateworks/gw_ventana/README
+++ b/board/gateworks/gw_ventana/README
@@ -3,53 +3,81 @@ U-Boot for the Gateworks Ventana Product Family boards
This file contains information for the port of U-Boot to the Gateworks
Ventana Product family boards.
-1. Boot source, boot from NAND
+1. Secondary Program Loader (SPL)
+---------------------------------
+
+The i.MX6 has a BOOT ROM PPL (Primary Program Loader) which supports loading
+an executable image from various boot devices.
+
+The Gateworks Ventana board config uses an SPL build configuration. This
+will build the following artifacts from u-boot source:
+ - SPL - Secondary Program Loader that the i.MX6 BOOT ROM (Primary Program
+ Loader) boots. This detects CPU/DRAM configuration, configures
+ The DRAM controller, loads u-boot.img from the detected boot device,
+ and jumps to it. As this is booted from the PPL, it has an IVT/DCD
+ table.
+ - u-boot.img - The main u-boot core which is u-boot.bin with a image header.
+
+
+2. Build
+--------
+
+To build U-Boot for the Gateworks Ventana product family:
+
+ make gwventana_config
+ make
+
+
+3. Boot source, boot from NAND
------------------------------
The i.MX6 BOOT ROM expects some structures that provide details of NAND layout
and bad block information (referred to as 'bootstreams') which are replicated
-multiple times in NAND. The number of replications is configurable through
-board strapping options and eFUSE settings. The Freescale 'kobs-ng'
-application from the Freescale LTIB BSP, which runs under Linux, must be used
-to program the bootstream in order to setup the replicated headers correctly.
+multiple times in NAND. The number of replications and their spacing (referred
+to as search stride) is configurable through board strapping options and/or
+eFUSE settings (BOOT_SEARCH_COUNT / Pages in block from BOOT_CFG2). In
+addition, the i.MX6 BOOT ROM Flash Configuration Block (FCB) supports two
+copies of a bootloader in flash in the case that a bad block has corrupted one.
+The Freescale 'kobs-ng' application from the Freescale LTIB BSP, which runs
+under Linux and operates on an MTD partition, must be used to program the
+bootstream in order to setup this flash structure correctly.
The Gateworks Ventana boards with NAND flash have been factory programmed
such that their eFUSE settings expect 2 copies of the boostream (this is
specified by providing kobs-ng with the --search_exponent=1 argument). Once in
-Linux with MTD support for the NAND on /dev/mtd0 you can program the boostream
+Linux with MTD support for the NAND on /dev/mtd0 you can program the SPL
with:
-kobs-ng init -v -x --search_exponent=1 u-boot.imx
+kobs-ng init -v -x --search_exponent=1 SPL
-The kobs-ng application uses an imximage (u-boot.imx) which contains the
-Image Vector Table (IVT) and Device Configuration Data (DCD) structures that
-the i.MX6 BOOT ROM requires to boot. The kobs-ng adds the Firmware
-Configuration Block (FCB) and Discovered Bad Block Table (DBBT).
+The kobs-ng application uses an imximage which contains the Image Vector Table
+(IVT) and Device Configuration Data (DCD) structures that the i.MX6 BOOT ROM
+requires to boot. The kobs-ng adds the Firmware Configuration Block (FCB) and
+Discovered Bad Block Table (DBBT). The SPL build artifact from u-boot is
+an imximage.
-This information is taken from:
- http://trac.gateworks.com/wiki/ventana/bootloader#NANDFLASH
+The u-boot.img, which is the non SPL u-boot binary appended to a u-boot image
+header must be programmed in the NAND flash boot device at an offset hard
+coded in the SPL. For the Ventana boards, this has been chosen to be 14MB.
+The image can be programmed from either u-boot or Linux:
-More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
-
-2. Build
---------
+u-boot:
+Ventana > setenv mtdparts mtdparts=nand:14m(spl),2m(uboot),1m(env),-(rootfs)
+Ventana > tftp ${loadaddr} u-boot.img && nand erase.part uboot && \
+ nand write ${loadaddr} uboot ${filesize}
-There are several Gateworks Ventana boards that share a simliar design but
-vary based on CPU, Memory configuration, and subloaded devices. Although
-the subloaded devices are handled dynamically in the bootloader using
-factory configured EEPROM data to modify the device-tree, the CPU choice
-(IMX6Q vs IMX6DL) and memory configurations are currently compile-time
-options.
+Linux:
+nandwrite /dev/mtd1 u-boot.img
-The following Gateworks Ventana configurations exist:
- gwventanaq1gspi: MX6Q,1GB,SPI FLASH
- gwventanaq : MX6Q,512MB,NAND FLASH
- gwventanaq1g : MX6Q,1GB,NAND FLASH
- gwventanadl : MX6DL,512MB,NAND FLASH
- gwventanadl1g : MX6DL,1GB,NAND FLASH
+The above assumes the default Ventana partitioning scheme which is configured
+via the mtdparts env var:
+ - spl: 14MB
+ - uboot: 2M
+ - env: 1M
+ - rootfs: the rest
-To build U-Boot for the MX6Q,1GB,NAND FLASH for example:
+This information is taken from:
+ http://trac.gateworks.com/wiki/ventana/bootloader#NANDFLASH
- make gwventanaq1g_config
- make
+More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
index 4ae458f..e581459 100644
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ b/board/gateworks/gw_ventana/gw_ventana.c
@@ -917,6 +917,7 @@ void get_board_serial(struct tag_serialnr *serialnr)
* Board Support
*/
+/* called from SPL board_init_f() */
int board_early_init_f(void)
{
setup_iomux_uart();
@@ -927,8 +928,7 @@ int board_early_init_f(void)
int dram_init(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
- CONFIG_DDR_MB*1024*1024);
+ gd->ram_size = imx_ddr_size();
return 0;
}
@@ -1070,9 +1070,11 @@ int misc_init_r(void)
* env scripts will try loading each from most specific to
* least.
*/
- if (is_cpu_type(MXC_CPU_MX6Q))
+ if (is_cpu_type(MXC_CPU_MX6Q) ||
+ is_cpu_type(MXC_CPU_MX6D))
cputype = "imx6q";
- else if (is_cpu_type(MXC_CPU_MX6DL))
+ else if (is_cpu_type(MXC_CPU_MX6DL) ||
+ is_cpu_type(MXC_CPU_MX6SOLO))
cputype = "imx6dl";
memset(str, 0, sizeof(str));
for (i = 0; i < (sizeof(str)-1) && info->model[i]; i++)
diff --git a/board/gateworks/gw_ventana/gw_ventana.cfg b/board/gateworks/gw_ventana/gw_ventana.cfg
index 27f0974..9ab95f5 100644
--- a/board/gateworks/gw_ventana/gw_ventana.cfg
+++ b/board/gateworks/gw_ventana/gw_ventana.cfg
@@ -24,21 +24,6 @@ BOOT_FROM nand
#define __ASSEMBLY__
#include <config.h>
-#include "asm/arch/mx6-ddr.h"
#include "asm/arch/iomux.h"
#include "asm/arch/crm_regs.h"
-
-/* Memory configuration (size is overridden via eeprom config) */
-#include "../../boundary/nitrogen6x/ddr-setup.cfg"
-#if defined(CONFIG_MX6Q) && CONFIG_DDR_MB == 1024
- #include "../../boundary/nitrogen6x/1066mhz_4x128mx16.cfg"
-#elif defined(CONFIG_MX6DL) && CONFIG_DDR_MB == 1024
- #include "../../boundary/nitrogen6x/800mhz_4x128mx16.cfg"
-#elif defined(CONFIG_MX6DL) && CONFIG_DDR_MB == 512
- #include "../../boundary/nitrogen6x/800mhz_2x128mx16.cfg"
-#elif defined(CONFIG_MX6Q) && CONFIG_DDR_MB == 512
- #include "../../boundary/nitrogen6x/800mhz_2x128mx16.cfg"
-#else
- #error "Unsupported CPU/Memory configuration"
-#endif
#include "clocks.cfg"
diff --git a/board/gateworks/gw_ventana/gw_ventana_spl.c b/board/gateworks/gw_ventana/gw_ventana_spl.c
new file mode 100644
index 0000000..e943879
--- /dev/null
+++ b/board/gateworks/gw_ventana/gw_ventana_spl.c
@@ -0,0 +1,419 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <spl.h>
+
+#include "ventana_eeprom.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
+#define I2C_GSC 0
+#define GSC_EEPROM_ADDR 0x51
+#define GSC_EEPROM_DDR_SIZE 0x2B /* enum (512,1024,2048) MB */
+#define GSC_EEPROM_DDR_WIDTH 0x2D /* enum (32,64) bit */
+#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* I2C1: GSC */
+static struct i2c_pads_info mx6q_i2c_pad_info0 = {
+ .scl = {
+ .i2c_mode = MX6Q_PAD_EIM_D21__I2C1_SCL | PC,
+ .gpio_mode = MX6Q_PAD_EIM_D21__GPIO3_IO21 | PC,
+ .gp = IMX_GPIO_NR(3, 21)
+ },
+ .sda = {
+ .i2c_mode = MX6Q_PAD_EIM_D28__I2C1_SDA | PC,
+ .gpio_mode = MX6Q_PAD_EIM_D28__GPIO3_IO28 | PC,
+ .gp = IMX_GPIO_NR(3, 28)
+ }
+};
+static struct i2c_pads_info mx6dl_i2c_pad_info0 = {
+ .scl = {
+ .i2c_mode = MX6DL_PAD_EIM_D21__I2C1_SCL | PC,
+ .gpio_mode = MX6DL_PAD_EIM_D21__GPIO3_IO21 | PC,
+ .gp = IMX_GPIO_NR(3, 21)
+ },
+ .sda = {
+ .i2c_mode = MX6DL_PAD_EIM_D28__I2C1_SDA | PC,
+ .gpio_mode = MX6DL_PAD_EIM_D28__GPIO3_IO28 | PC,
+ .gp = IMX_GPIO_NR(3, 28)
+ }
+};
+
+static void i2c_setup_iomux(void)
+{
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info0);
+ else
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info0);
+}
+
+/* configure MX6Q/DUAL mmdc DDR io registers */
+struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
+ /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ /* SDCKE[0:1]: 100k pull-up */
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ /* SDBA2: pull-up disabled */
+ .dram_sdba2 = 0x00000000,
+ /* SDODT[0:1]: 100k pull-up, 40 ohm */
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+
+ /* DQM[0:7]: Differential input, 40 ohm */
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+/* configure MX6Q/DUAL mmdc GRP io registers */
+struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
+ /* DDR3 */
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ /* disable DDR pullups */
+ .grp_ddrpke = 0x00000000,
+ /* ADDR[00:16], SDBA[0:1]: 40 ohm */
+ .grp_addds = 0x00000030,
+ /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+ .grp_ctlds = 0x00000030,
+ /* DATA[00:63]: Differential input, 40 ohm */
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
+struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
+ /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ /* SDCKE[0:1]: 100k pull-up */
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ /* SDBA2: pull-up disabled */
+ .dram_sdba2 = 0x00000000,
+ /* SDODT[0:1]: 100k pull-up, 40 ohm */
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+
+ /* DQM[0:7]: Differential input, 40 ohm */
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
+struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+ /* DDR3 */
+ .grp_ddr_type = 0x000c0000,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .grp_ddrmode_ctl = 0x00020000,
+ /* disable DDR pullups */
+ .grp_ddrpke = 0x00000000,
+ /* ADDR[00:16], SDBA[0:1]: 40 ohm */
+ .grp_addds = 0x00000030,
+ /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+ .grp_ctlds = 0x00000030,
+ /* DATA[00:63]: Differential input, 40 ohm */
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+/* MT41K128M16JT-125 */
+static struct mx6_ddr3_cfg mt41k128m16jt_125 = {
+ .mem_speed = 1600,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+/* GW54xx specific calibration */
+static struct mx6_mmdc_calibration gw54xxq_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x00190018,
+ .p0_mpwldectrl1 = 0x0021001D,
+ .p1_mpwldectrl0 = 0x00160027,
+ .p1_mpwldectrl1 = 0x0012001E,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x43370346,
+ .p0_mpdgctrl1 = 0x032A0321,
+ .p1_mpdgctrl0 = 0x433A034D,
+ .p1_mpdgctrl1 = 0x032F0235,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x3C313539,
+ .p1_mprddlctl = 0x37333140,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x37393C38,
+ .p1_mpwrdlctl = 0x42334538,
+};
+
+/* GW53xx specific calibration */
+static struct mx6_mmdc_calibration gw53xxq_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x00160013,
+ .p0_mpwldectrl1 = 0x00090024,
+ .p1_mpwldectrl0 = 0x001F0018,
+ .p1_mpwldectrl1 = 0x000C001C,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x433A034C,
+ .p0_mpdgctrl1 = 0x0336032F,
+ .p1_mpdgctrl0 = 0x4343034A,
+ .p1_mpdgctrl1 = 0x03370222,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x3F343638,
+ .p1_mprddlctl = 0x38373442,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x343A3E39,
+ .p1_mpwrdlctl = 0x44344239,
+};
+static struct mx6_mmdc_calibration gw53xxdl_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x003C003C,
+ .p0_mpwldectrl1 = 0x00330038,
+ .p1_mpwldectrl0 = 0x001F002A,
+ .p1_mpwldectrl1 = 0x0022003F,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x42410244,
+ .p0_mpdgctrl1 = 0x022D022D,
+ .p1_mpdgctrl0 = 0x4234023A,
+ .p1_mpdgctrl1 = 0x021C0228,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x484A4C4B,
+ .p1_mprddlctl = 0x4B4D4E4B,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x33342B32,
+ .p1_mpwrdlctl = 0x3933332B,
+};
+
+/* GW52xx specific calibration */
+static struct mx6_mmdc_calibration gw52xxdl_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x0040003F,
+ .p0_mpwldectrl1 = 0x00370037,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x42420244,
+ .p0_mpdgctrl1 = 0x022F022F,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x49464B4A,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x32362C32,
+};
+
+/* GW51xx specific calibration */
+static struct mx6_mmdc_calibration gw51xxq_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x00150016,
+ .p0_mpwldectrl1 = 0x001F0017,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x433D034D,
+ .p0_mpdgctrl1 = 0x033D032F,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x3F313639,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x33393F36,
+};
+
+static struct mx6_mmdc_calibration gw51xxdl_mmdc_calib = {
+ /* write leveling calibration determine */
+ .p0_mpwldectrl0 = 0x003D003F,
+ .p0_mpwldectrl1 = 0x002F0038,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x423A023A,
+ .p0_mpdgctrl1 = 0x022A0228,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x48494C4C,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x34352D31,
+};
+
+static void spl_dram_init(int width, int size, int board_model)
+{
+ struct mx6_ddr3_cfg *mem = &mt41k128m16jt_125;
+ struct mx6_mmdc_calibration *calib;
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus:0=16,1=32,2=64 */
+ .dsize = width/32,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ /* single chip select */
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+ .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
+#else
+ .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
+#endif
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ };
+
+ /*
+ * MMDC Calibration requires the following data:
+ * mx6_mmdc_calibration - board-specific calibration (routing delays)
+ * mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
+ * mx6_ddr_cfg - chip specific timing/layout details
+ */
+ switch (board_model) {
+ default:
+ case GW51xx:
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ calib = &gw51xxq_mmdc_calib;
+ else
+ calib = &gw51xxdl_mmdc_calib;
+ break;
+ case GW52xx:
+ calib = &gw52xxdl_mmdc_calib;
+ break;
+ case GW53xx:
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ calib = &gw53xxq_mmdc_calib;
+ else
+ calib = &gw53xxdl_mmdc_calib;
+ break;
+ case GW54xx:
+ calib = &gw54xxq_mmdc_calib;
+ break;
+ }
+
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ mx6dq_dram_iocfg(width, &mx6dq_ddr_ioregs,
+ &mx6dq_grp_ioregs);
+ else
+ mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs,
+ &mx6sdl_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, calib, mem);
+}
+
+/*
+ * called from C runtime startup code (arch/arm/lib/crt0.S:_main)
+ * - we have a stack and a place to store GD, both in SRAM
+ * - no variable global data is available
+ */
+void board_init_f(ulong dummy)
+{
+ struct ventana_board_info ventana_info;
+ int board_model;
+
+ /*
+ * Zero out global data:
+ * - this shoudl be done by crt0.S
+ * - failure to zero it will cause i2c_setup to fail
+ */
+ memset((void *)gd, 0, sizeof(struct global_data));
+
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ /* iomux and setup of i2c */
+ board_early_init_f();
+ i2c_setup_iomux();
+
+ /* setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* read/validate EEPROM info to determine board model and SDRAM cfg */
+ board_model = read_eeprom(I2C_GSC, &ventana_info);
+
+ /* provide some some default: 32bit 128MB */
+ if (GW_UNKNOWN == board_model) {
+ ventana_info.sdram_width = 2;
+ ventana_info.sdram_size = 3;
+ }
+
+ /* configure MMDC for SDRAM width/size and per-model calibration */
+ spl_dram_init(8 << ventana_info.sdram_width,
+ 16 << ventana_info.sdram_size,
+ board_model);
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
+
+void reset_cpu(ulong addr)
+{
+}
diff --git a/boards.cfg b/boards.cfg
index 983c657..0dc8c2e 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -322,11 +322,7 @@ Active arm armv7 mx6 freescale mx6qsabreauto
Active arm armv7 mx6 freescale mx6sabresd mx6dlsabresd mx6sabresd:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL Fabio Estevam <fabio.estevam@freescale.com>
Active arm armv7 mx6 freescale mx6sabresd mx6qsabresd mx6sabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q Fabio Estevam <fabio.estevam@freescale.com>
Active arm armv7 mx6 freescale mx6slevk mx6slevk mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL Fabio Estevam <fabio.estevam@freescale.com>
-Active arm armv7 mx6 gateworks gw_ventana gwventanadl gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6DL,DDR_MB=512 Tim Harvey <tharvey@gateworks.com>
-Active arm armv7 mx6 gateworks gw_ventana gwventanadl1g gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6DL,DDR_MB=1024 Tim Harvey <tharvey@gateworks.com>
-Active arm armv7 mx6 gateworks gw_ventana gwventanaq gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6Q,DDR_MB=512 Tim Harvey <tharvey@gateworks.com>
-Active arm armv7 mx6 gateworks gw_ventana gwventanaq1g gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6Q,DDR_MB=1024 Tim Harvey <tharvey@gateworks.com>
-Active arm armv7 mx6 gateworks gw_ventana gwventanaq1gspi gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6Q,DDR_MB=1024,SPI_FLASH Tim Harvey <tharvey@gateworks.com>
+Active arm armv7 mx6 gateworks gw_ventana gwventana gw_ventana:IMX_CONFIG=board/gateworks/gw_ventana/gw_ventana.cfg,MX6QDL,SPL Tim Harvey <tharvey@gateworks.com>
Active arm armv7 mx6 solidrun hummingboard hummingboard_solo hummingboard:IMX_CONFIG=board/solidrun/hummingboard/solo.cfg,MX6S,DDR_MB=512 Jon Nettleton <jon.nettleton@gmail.com>
Active arm armv7 omap3 - overo omap3_overo - Steve Sakoman <sakoman@gmail.com>
Active arm armv7 omap3 - pandora omap3_pandora - Grazvydas Ignotas <notasas@gmail.com>
diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
index 3398390..cd53737 100644
--- a/include/configs/gw_ventana.h
+++ b/include/configs/gw_ventana.h
@@ -7,6 +7,17 @@
#ifndef __CONFIG_H
#define __CONFIG_H
+/* SPL */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+/*
+#define CONFIG_SPL_SATA_SUPPORT
+*/
+/* Location in NAND to read U-Boot from */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * 1024 * 1024)
+
+#include "imx6_spl.h" /* common IMX6 SPL configuration */
#include "mx6_common.h"
#define CONFIG_MX6
#define CONFIG_DISPLAY_CPUINFO /* display cpu info */
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE
2014-05-08 5:16 ` [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE Tim Harvey
@ 2014-05-14 8:52 ` Masahiro Yamada
2014-05-14 10:14 ` Stefano Babic
2014-05-15 8:31 ` Stefano Babic
1 sibling, 1 reply; 30+ messages in thread
From: Masahiro Yamada @ 2014-05-14 8:52 UTC (permalink / raw)
To: u-boot
Hi.
On Wed, 7 May 2014 22:16:12 -0700
Tim Harvey <tharvey@gateworks.com> wrote:
> We only need to read in the size of struct image_header and thus don't
> need to know the page size of the nand device.
>
> Cc: Scott Wood <scottwood@freescale.com>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> Acked-by: Stefano Babic <sbabic@denx.de>
> Acked-by: Scott Wood <scottwood@freescale.com>
> ---
> v3:
> - no changes
>
> v2:
> - cc Scott Wood <scottwood@freescale.com> on this
> - Acked-by: Stefano Babic <sbabic@denx.de>
> - Acked-by: Scott Wood <scottwood@freescale.com>
When and by whom will this patch be applied?
Since this is not IMX-specific,
I'd like this patch to be applied first.
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE
2014-05-14 8:52 ` Masahiro Yamada
@ 2014-05-14 10:14 ` Stefano Babic
0 siblings, 0 replies; 30+ messages in thread
From: Stefano Babic @ 2014-05-14 10:14 UTC (permalink / raw)
To: u-boot
Hi Masahiro,
On 14/05/2014 10:52, Masahiro Yamada wrote:
> Hi.
>
> On Wed, 7 May 2014 22:16:12 -0700
> Tim Harvey <tharvey@gateworks.com> wrote:
>
>> We only need to read in the size of struct image_header and thus don't
>> need to know the page size of the nand device.
>>
>> Cc: Scott Wood <scottwood@freescale.com>
>> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
>> Acked-by: Stefano Babic <sbabic@denx.de>
>> Acked-by: Scott Wood <scottwood@freescale.com>
>> ---
>> v3:
>> - no changes
>>
>> v2:
>> - cc Scott Wood <scottwood@freescale.com> on this
>> - Acked-by: Stefano Babic <sbabic@denx.de>
>> - Acked-by: Scott Wood <scottwood@freescale.com>
>
> When and by whom will this patch be applied?
>
> Since this is not IMX-specific,
> I'd like this patch to be applied first.
>
It is not iMX specific, but in the last iteration Scott acked it and
give us indication to let it in the patchset - plan was to apply the
patchset as a whole in one shot, that is by me.
I can propose I apply this (and maybe a couple of other patches in this
patchset that have already passed the review and they were acked) and
this is part of my next pull request to Albert. Or maybe Tom decides to
apply it directly to master, and Tim drops it from the patchset.
Best regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE
2014-05-08 5:16 ` [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE Tim Harvey
2014-05-14 8:52 ` Masahiro Yamada
@ 2014-05-15 8:31 ` Stefano Babic
1 sibling, 0 replies; 30+ messages in thread
From: Stefano Babic @ 2014-05-15 8:31 UTC (permalink / raw)
To: u-boot
On 08/05/2014 07:16, Tim Harvey wrote:
> We only need to read in the size of struct image_header and thus don't
> need to know the page size of the nand device.
>
> Cc: Scott Wood <scottwood@freescale.com>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> Acked-by: Stefano Babic <sbabic@denx.de>
> Acked-by: Scott Wood <scottwood@freescale.com>
> ---
As discussed : applied to u-boot-imx, thanks.
Tim, please remove it in your next post, thanks.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
` (10 preceding siblings ...)
2014-05-08 5:16 ` [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL Tim Harvey
@ 2014-05-22 6:14 ` Tim Harvey
2014-05-22 6:34 ` Stefano Babic
11 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-22 6:14 UTC (permalink / raw)
To: u-boot
On Wed, May 7, 2014 at 10:16 PM, Tim Harvey <tharvey@gateworks.com> wrote:
> This series adds some necessary framework for IMX6 SPL support. The series
> includes support for NAND SPL and has been tested with MMC as well. I have
> tested this on five differing Ventana baseboards with a variety of memory
> (32bit 512MB, 32bit 1024MB, 64bit 1024MB) and CPU configurations (IMX6Q,
> IMX6DL, IMX6S).
>
> This is based on top of Mashahiro Yamada's patch that consolidates
> arch/arm/include/asm/arch-*/spl.h [1]
>
> v3:
> - re-ordered calls in board_init_f
> - replace imx_iomux_v3_setup_multiple_pads_array with additional intelligence
> in imx_iomux_v3_setup_multiple_pads
> - added ifdef's around cpu specific mmdc iocfg functions for code-reduction
> with single-variant board configs
> - added checks for IMX6D
> - added Freescale copyright to boot device support function
> - fixed typo s/IMX6SLD/IMX6SDL
> - encorporated cleanups in mxs_nand_spl.c per feedback
>
> v2:
> - use compatible linker script instead of creating new one
> - remove structure passing data from SPL to u-boot
> - remove dependence on mtdpart, mtdcore, nand_util, nand_ecc, nand_base
> and nand_bbt to bring SPL down in size. This reduced codesize by about 32k
> where now mxs_spl_nand is about 12k total
> - adjust CONFIG_SPL_TEXT_BASE, CONFIG_SPL_STACK and CONFIG_SPL_MAX_SIZE
> to accomodate the IMX6SOLO/DUALLITE which have half the iRAM of the
> IMX6DUAL/IMX6QUAD
> - move boot dev detection into imx-common/spl.c
> - move macros for using pinmux array into iomux-v3.h
> - remove missing/unnecessary include
> - revert mtdparts change
> - use get_ram_size() to detect memory
> - add support for MX6SOLO and MX6DUAL
> - set CS0_END for 4GB so get_ram_size() works
> - updated DDR3 calibration values for ventana boards
> - fixed build issue - only compile spl if doing spl build
> - fixed line length issue in README
> - remove CONFIG_SPL* conditions and conditionally compile instead
> - removed prints for CPU type and DRAM size/width - uboot will print these l
> - removed unused gw_ventana_spl.cfg
> - use common read_eeprom function
> - added MMC support to SPL
> - added Masahiro Yamada's boot mode consolidation patch
> http://patchwork.ozlabs.org/patch/341817 and rebase on top of it
>
> [1] http://patchwork.ozlabs.org/patch/341817/
>
> Tim Harvey (11):
> SPL: NAND: remove CONFIG_SYS_NAND_PAGE_SIZE
> SPL: NAND: add support for mxs nand
> MX6: add common SPL configuration
> MX6: add boot device support for SPL
> IMX: add comments and remove unused struct fields
> MX6: add structs for mmdc and ddr iomux registers
> MX6: add mmdc configuration for MX6Q/MX6DL
> IMX: iomux: add macros to setup iomux for multiple SoC types
> IMX: ventana: split read_eeprom into standalone file
> IMX: ventana: auto-configure for IMX6Q vs IMX6DL
> IMX: ventana: switch to SPL
>
> arch/arm/cpu/armv7/mx6/Makefile | 1 +
> arch/arm/cpu/armv7/mx6/ddr.c | 473 ++++++++++++++++++++++
> arch/arm/imx-common/Makefile | 1 +
> arch/arm/imx-common/cpu.c | 16 +-
> arch/arm/imx-common/iomux-v3.c | 16 +-
> arch/arm/imx-common/spl.c | 81 ++++
> arch/arm/include/asm/arch-mx6/mx6-ddr.h | 231 +++++++++++
> arch/arm/include/asm/imx-common/iomux-v3.h | 25 ++
> board/gateworks/gw_ventana/Makefile | 3 +-
> board/gateworks/gw_ventana/README | 92 +++--
> board/gateworks/gw_ventana/eeprom.c | 89 +++++
> board/gateworks/gw_ventana/gw_ventana.c | 591 +++++++++++++++-------------
> board/gateworks/gw_ventana/gw_ventana.cfg | 15 -
> board/gateworks/gw_ventana/gw_ventana_spl.c | 419 ++++++++++++++++++++
> board/gateworks/gw_ventana/ventana_eeprom.h | 11 +
> boards.cfg | 6 +-
> common/spl/spl_nand.c | 2 +-
> drivers/mtd/nand/Makefile | 1 +
> drivers/mtd/nand/mxs_nand_spl.c | 231 +++++++++++
> include/configs/gw_ventana.h | 11 +
> include/configs/imx6_spl.h | 71 ++++
> 21 files changed, 2047 insertions(+), 339 deletions(-)
> create mode 100644 arch/arm/cpu/armv7/mx6/ddr.c
> create mode 100644 arch/arm/imx-common/spl.c
> create mode 100644 board/gateworks/gw_ventana/eeprom.c
> create mode 100644 board/gateworks/gw_ventana/gw_ventana_spl.c
> create mode 100644 drivers/mtd/nand/mxs_nand_spl.c
> create mode 100644 include/configs/imx6_spl.h
>
> --
> 1.8.3.2
>
Stefano,
Any comments on this series? I realize you've applied the first one
and I'll remove that from any subsequent posts.
Regards,
Tim
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support
2014-05-22 6:14 ` [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
@ 2014-05-22 6:34 ` Stefano Babic
2014-05-22 22:17 ` Tim Harvey
0 siblings, 1 reply; 30+ messages in thread
From: Stefano Babic @ 2014-05-22 6:34 UTC (permalink / raw)
To: u-boot
Hi Tim,
On 22/05/2014 08:14, Tim Harvey wrote:
> Stefano,
>
> Any comments on this series? I realize you've applied the first one
> and I'll remove that from any subsequent posts.
Right.
>
I think we have a very good point (nice work !) and we are near to merge
the patchset. If I am not wrong, you want to post an update for the MMDC
config patch, do you ?
Patch 2 should be acked by Scott because it belongs to his area of
competence.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support
2014-05-22 6:34 ` Stefano Babic
@ 2014-05-22 22:17 ` Tim Harvey
0 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-22 22:17 UTC (permalink / raw)
To: u-boot
On Wed, May 21, 2014 at 11:34 PM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Tim,
>
> On 22/05/2014 08:14, Tim Harvey wrote:
>
>> Stefano,
>>
>> Any comments on this series? I realize you've applied the first one
>> and I'll remove that from any subsequent posts.
>
> Right.
>>
>
> I think we have a very good point (nice work !) and we are near to merge
> the patchset. If I am not wrong, you want to post an update for the MMDC
> config patch, do you ?
Yes, I do have an update for that particular patch, but I don't think
anyone has commented on that patch either way. I'll go ahead and
respond to that thread with my update as that is the only
non-submitted change I have.
Thanks,
Tim
>
> Patch 2 should be acked by Scott because it belongs to his area of
> competence.
>
> Best regards,
> Stefano Babic
>
> --
> =====================================================================
> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> =====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v4 07/11] mx6: add mmdc configuration for MX6Q/MX6DL
2014-05-08 5:16 ` [U-Boot] [PATCH v3 07/11] mx6: add mmdc configuration for MX6Q/MX6DL Tim Harvey
@ 2014-05-22 22:28 ` Tim Harvey
0 siblings, 0 replies; 30+ messages in thread
From: Tim Harvey @ 2014-05-22 22:28 UTC (permalink / raw)
To: u-boot
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
chip-specific data
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v4:
- added delay following configure to allow ZQ calibration to complete
- update MMDC configuration to match Freescale RM
v3:
- added ifdef's around cpu specific iocfg functions for code-reduction with
single-variant board configs
- moved portions from previous patch here
- added check for IMX6D
v2:
- split out mmdc and iomux structs into separate patch
---
arch/arm/cpu/armv7/mx6/Makefile | 1 +
arch/arm/cpu/armv7/mx6/ddr.c | 490 ++++++++++++++++++++++++++++++++
arch/arm/include/asm/arch-mx6/mx6-ddr.h | 72 +++++
3 files changed, 563 insertions(+)
create mode 100644 arch/arm/cpu/armv7/mx6/ddr.c
diff --git a/arch/arm/cpu/armv7/mx6/Makefile b/arch/arm/cpu/armv7/mx6/Makefile
index d7285fc..6dc9f8e 100644
--- a/arch/arm/cpu/armv7/mx6/Makefile
+++ b/arch/arm/cpu/armv7/mx6/Makefile
@@ -8,4 +8,5 @@
#
obj-y := soc.o clock.o
+obj-$(CONFIG_SPL_BUILD) += ddr.o
obj-$(CONFIG_SECURE_BOOT) += hab.o
diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
new file mode 100644
index 0000000..0434211
--- /dev/null
+++ b/arch/arm/cpu/armv7/mx6/ddr.c
@@ -0,0 +1,490 @@
+/*
+ * Copyright (C) 2014 Gateworks Corporation
+ * Author: Tim Harvey <tharvey@gateworks.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/types.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/types.h>
+
+#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
+/* Configure MX6DQ mmdc iomux */
+void mx6dq_dram_iocfg(unsigned width,
+ const struct mx6dq_iomux_ddr_regs *ddr,
+ const struct mx6dq_iomux_grp_regs *grp)
+{
+ volatile struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux;
+ volatile struct mx6dq_iomux_grp_regs *mx6_grp_iomux;
+
+ mx6_ddr_iomux = (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE;
+ mx6_grp_iomux = (struct mx6dq_iomux_grp_regs *)MX6DQ_IOM_GRP_BASE;
+
+ /* DDR IO Type */
+ mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
+ mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
+
+ /* Clock */
+ mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
+ mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1;
+
+ /* Address */
+ mx6_ddr_iomux->dram_cas = ddr->dram_cas;
+ mx6_ddr_iomux->dram_ras = ddr->dram_ras;
+ mx6_grp_iomux->grp_addds = grp->grp_addds;
+
+ /* Control */
+ mx6_ddr_iomux->dram_reset = ddr->dram_reset;
+ mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0;
+ mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1;
+ mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
+ mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0;
+ mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1;
+ mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
+
+ /* Data Strobes */
+ mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
+ mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
+ mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
+ mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4;
+ mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5;
+ mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6;
+ mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7;
+ }
+
+ /* Data */
+ mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
+ mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
+ mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
+ if (width >= 32) {
+ mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
+ mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
+ }
+ if (width >= 64) {
+ mx6_grp_iomux->grp_b4ds = grp->grp_b4ds;
+ mx6_grp_iomux->grp_b5ds = grp->grp_b5ds;
+ mx6_grp_iomux->grp_b6ds = grp->grp_b6ds;
+ mx6_grp_iomux->grp_b7ds = grp->grp_b7ds;
+ }
+ mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
+ mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
+ mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4;
+ mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5;
+ mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6;
+ mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7;
+ }
+}
+#endif
+
+#if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
+/* Configure MX6SDL mmdc iomux */
+void mx6sdl_dram_iocfg(unsigned width,
+ const struct mx6sdl_iomux_ddr_regs *ddr,
+ const struct mx6sdl_iomux_grp_regs *grp)
+{
+ volatile struct mx6sdl_iomux_ddr_regs *mx6_ddr_iomux;
+ volatile struct mx6sdl_iomux_grp_regs *mx6_grp_iomux;
+
+ mx6_ddr_iomux = (struct mx6sdl_iomux_ddr_regs *)MX6SDL_IOM_DDR_BASE;
+ mx6_grp_iomux = (struct mx6sdl_iomux_grp_regs *)MX6SDL_IOM_GRP_BASE;
+
+ /* DDR IO Type */
+ mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type;
+ mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke;
+
+ /* Clock */
+ mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0;
+ mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1;
+
+ /* Address */
+ mx6_ddr_iomux->dram_cas = ddr->dram_cas;
+ mx6_ddr_iomux->dram_ras = ddr->dram_ras;
+ mx6_grp_iomux->grp_addds = grp->grp_addds;
+
+ /* Control */
+ mx6_ddr_iomux->dram_reset = ddr->dram_reset;
+ mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0;
+ mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1;
+ mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2;
+ mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0;
+ mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1;
+ mx6_grp_iomux->grp_ctlds = grp->grp_ctlds;
+
+ /* Data Strobes */
+ mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl;
+ mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0;
+ mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2;
+ mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4;
+ mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5;
+ mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6;
+ mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7;
+ }
+
+ /* Data */
+ mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode;
+ mx6_grp_iomux->grp_b0ds = grp->grp_b0ds;
+ mx6_grp_iomux->grp_b1ds = grp->grp_b1ds;
+ if (width >= 32) {
+ mx6_grp_iomux->grp_b2ds = grp->grp_b2ds;
+ mx6_grp_iomux->grp_b3ds = grp->grp_b3ds;
+ }
+ if (width >= 64) {
+ mx6_grp_iomux->grp_b4ds = grp->grp_b4ds;
+ mx6_grp_iomux->grp_b5ds = grp->grp_b5ds;
+ mx6_grp_iomux->grp_b6ds = grp->grp_b6ds;
+ mx6_grp_iomux->grp_b7ds = grp->grp_b7ds;
+ }
+ mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0;
+ mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1;
+ if (width >= 32) {
+ mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2;
+ mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3;
+ }
+ if (width >= 64) {
+ mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4;
+ mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5;
+ mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6;
+ mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7;
+ }
+}
+#endif
+
+/*
+ * Configure mx6 mmdc registers based on:
+ * - board-specific memory configuration
+ * - board-specific calibration data
+ * - ddr3 chip details
+ *
+ * The various calculations here are derived from the Freescale
+ * i.Mx6DQSDL DDR3 Script Aid spreadsheet (DOC-94917) designed to generate MMDC
+ * configuration registers based on memory system and memory chip parameters.
+ *
+ * The defaults here are those which were specified in the spreadsheet.
+ * For details on each register, refer to the IMX6DQRM and/or IMX6SDLRM
+ * section titled MMDC initialization
+ */
+#define MR(val, ba, cmd, cs1) \
+ ((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba)
+void mx6_dram_cfg(const struct mx6_ddr_sysinfo *i,
+ const struct mx6_mmdc_calibration *c,
+ const struct mx6_ddr3_cfg *m)
+{
+ volatile struct mmdc_p_regs *mmdc0;
+ volatile struct mmdc_p_regs *mmdc1;
+ u32 reg;
+ u8 tcke, tcksrx, tcksre, txpdll, taofpd, taonpd, trrd;
+ u8 todtlon, taxpd, tanpd, tcwl, txp, tfaw, tcl;
+ u8 todt_idle_off = 0x4; /* from DDR3 Script Aid spreadsheet */
+ u16 trcd, trc, tras, twr, tmrd, trtp, trp, twtr, trfc, txs, txpr;
+ u16 CS0_END;
+ u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
+ int clkper; /* clock period in picoseconds */
+ int clock; /* clock freq in mHz */
+ int cs;
+
+ mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
+ mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
+
+ /* MX6D/MX6Q: 1066 MHz memory clock, clkper = 1.894ns = 1894ps */
+ if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) {
+ clock = 528;
+ tcwl = 4;
+ }
+ /* MX6S/MX6DL: 800 MHz memory clock, clkper = 2.5ns = 2500ps */
+ else {
+ clock = 400;
+ tcwl = 3;
+ }
+ clkper = (1000*1000)/clock; /* ps */
+ todtlon = tcwl;
+ taxpd = tcwl;
+ tanpd = tcwl;
+ tcwl = tcwl;
+
+ switch (m->density) {
+ case 1: /* 1Gb per chip */
+ trfc = DIV_ROUND_UP(110000, clkper) - 1;
+ txs = DIV_ROUND_UP(120000, clkper) - 1;
+ break;
+ case 2: /* 2Gb per chip */
+ trfc = DIV_ROUND_UP(160000, clkper) - 1;
+ txs = DIV_ROUND_UP(170000, clkper) - 1;
+ break;
+ case 4: /* 4Gb per chip */
+ trfc = DIV_ROUND_UP(260000, clkper) - 1;
+ txs = DIV_ROUND_UP(270000, clkper) - 1;
+ break;
+ case 8: /* 8Gb per chip */
+ trfc = DIV_ROUND_UP(350000, clkper) - 1;
+ txs = DIV_ROUND_UP(360000, clkper) - 1;
+ break;
+ default:
+ /* invalid density */
+ printf("invalid chip density\n");
+ hang();
+ break;
+ }
+ txpr = txs;
+
+ switch (m->mem_speed) {
+ case 800:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(40000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(50000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ }
+ break;
+ case 1066:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 7500), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(37500, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(50000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 10000), clkper) - 1;
+ }
+ break;
+ case 1333:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 5625), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(30000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(45000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ }
+ break;
+ case 1600:
+ txp = DIV_ROUND_UP(MAX(3*clkper, 6000), clkper) - 1;
+ tcke = DIV_ROUND_UP(MAX(3*clkper, 5000), clkper) - 1;
+ if (m->pagesz == 1) {
+ tfaw = DIV_ROUND_UP(30000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 6000), clkper) - 1;
+ } else {
+ tfaw = DIV_ROUND_UP(40000, clkper) - 1;
+ trrd = DIV_ROUND_UP(MAX(4*clkper, 7500), clkper) - 1;
+ }
+ break;
+ default:
+ printf("invalid memory speed\n");
+ hang();
+ break;
+ }
+ txpdll = DIV_ROUND_UP(MAX(10*clkper, 24000), clkper) - 1;
+ tcl = DIV_ROUND_UP(m->trcd, clkper/10) - 3;
+ tcksre = DIV_ROUND_UP(MAX(5*clkper, 10000), clkper);
+ tcksrx = tcksre;
+ taonpd = DIV_ROUND_UP(2000, clkper) - 1;
+ taofpd = taonpd;
+ trp = DIV_ROUND_UP(m->trcd, clkper/10) - 1;
+ trcd = trp;
+ trc = DIV_ROUND_UP(m->trcmin, clkper/10) - 1;
+ tras = DIV_ROUND_UP(m->trasmin, clkper/10) - 1;
+ twr = DIV_ROUND_UP(15000, clkper) - 1;
+ tmrd = DIV_ROUND_UP(MAX(12*clkper, 15000), clkper) - 1;
+ twtr = ROUND(MAX(4*clkper, 7500)/clkper, 1) - 1;
+ trtp = twtr;
+ CS0_END = ((4*i->cs_density) <= 120) ? (4*i->cs_density)+7 : 127;
+ debug("density:%d Gb (%d Gb per chip)\n", i->cs_density, m->density);
+ debug("clock: %dMHz (%d ps)\n", clock, clkper);
+ debug("memspd:%d\n", m->mem_speed);
+ debug("tcke=%d\n", tcke);
+ debug("tcksrx=%d\n", tcksrx);
+ debug("tcksre=%d\n", tcksre);
+ debug("taofpd=%d\n", taofpd);
+ debug("taonpd=%d\n", taonpd);
+ debug("todtlon=%d\n", todtlon);
+ debug("tanpd=%d\n", tanpd);
+ debug("taxpd=%d\n", taxpd);
+ debug("trfc=%d\n", trfc);
+ debug("txs=%d\n", txs);
+ debug("txp=%d\n", txp);
+ debug("txpdll=%d\n", txpdll);
+ debug("tfaw=%d\n", tfaw);
+ debug("tcl=%d\n", tcl);
+ debug("trcd=%d\n", trcd);
+ debug("trp=%d\n", trp);
+ debug("trc=%d\n", trc);
+ debug("tras=%d\n", tras);
+ debug("twr=%d\n", twr);
+ debug("tmrd=%d\n", tmrd);
+ debug("tcwl=%d\n", tcwl);
+ debug("tdllk=%d\n", tdllk);
+ debug("trtp=%d\n", trtp);
+ debug("twtr=%d\n", twtr);
+ debug("trrd=%d\n", trrd);
+ debug("txpr=%d\n", txpr);
+ debug("CS0_END=%d\n", CS0_END);
+ debug("ncs=%d\n", i->ncs);
+ debug("Rtt_wr=%d\n", i->rtt_wr);
+ debug("Rtt_nom=%d\n", i->rtt_nom);
+ debug("SRT=%d\n", m->SRT);
+ debug("tcl=%d\n", tcl);
+ debug("twr=%d\n", twr);
+
+ /*
+ * board-specific configuration:
+ * These values are determined empirically and vary per board layout
+ * see:
+ * appnote, ddr3 spreadsheet
+ */
+ mmdc0->mpwldectrl0 = c->p0_mpwldectrl0;
+ mmdc0->mpwldectrl1 = c->p0_mpwldectrl1;
+ mmdc0->mpdgctrl0 = c->p0_mpdgctrl0;
+ mmdc0->mpdgctrl1 = c->p0_mpdgctrl1;
+ mmdc0->mprddlctl = c->p0_mprddlctl;
+ mmdc0->mpwrdlctl = c->p0_mpwrdlctl;
+ if (i->dsize > 1) {
+ mmdc1->mpwldectrl0 = c->p1_mpwldectrl0;
+ mmdc1->mpwldectrl1 = c->p1_mpwldectrl1;
+ mmdc1->mpdgctrl0 = c->p1_mpdgctrl0;
+ mmdc1->mpdgctrl1 = c->p1_mpdgctrl1;
+ mmdc1->mprddlctl = c->p1_mprddlctl;
+ mmdc1->mpwrdlctl = c->p1_mpwrdlctl;
+ }
+
+ /* Read data DQ Byte0-3 delay */
+ mmdc0->mprddqby0dl = (u32)0x33333333;
+ mmdc0->mprddqby1dl = (u32)0x33333333;
+ if (i->dsize > 0) {
+ mmdc0->mprddqby2dl = (u32)0x33333333;
+ mmdc0->mprddqby3dl = (u32)0x33333333;
+ }
+ if (i->dsize > 1) {
+ mmdc1->mprddqby0dl = (u32)0x33333333;
+ mmdc1->mprddqby1dl = (u32)0x33333333;
+ mmdc1->mprddqby2dl = (u32)0x33333333;
+ mmdc1->mprddqby3dl = (u32)0x33333333;
+ }
+
+ /* MMDC Termination: rtt_nom:2 RZQ/2(120ohm), rtt_nom:1 RZQ/4(60ohm) */
+ reg = (i->rtt_nom == 2) ? 0x00011117 : 0x00022227;
+ mmdc0->mpodtctrl = reg;
+ if (i->dsize > 1)
+ mmdc1->mpodtctrl = reg;
+
+ /* complete calibration */
+ reg = (1 << 11); /* Force measurement on delay-lines */
+ mmdc0->mpmur0 = reg;
+ if (i->dsize > 1)
+ mmdc1->mpmur0 = reg;
+
+ /* Step 1: configuration request */
+ mmdc0->mdscr = (u32)(1 << 15); /* config request */
+
+ /* Step 2: Timing configuration */
+ reg = (trfc << 24) | (txs << 16) | (txp << 13) | (txpdll << 9) |
+ (tfaw << 4) | tcl;
+ mmdc0->mdcfg0 = reg;
+ reg = (trcd << 29) | (trp << 26) | (trc << 21) | (tras << 16) |
+ (1 << 15) | /* trpa */
+ (twr << 9) | (tmrd << 5) | tcwl;
+ mmdc0->mdcfg1 = reg;
+ reg = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd;
+ mmdc0->mdcfg2 = reg;
+ reg = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) | (taxpd << 16) |
+ (todtlon << 12) | (todt_idle_off << 4);
+ mmdc0->mdotc = reg;
+ mmdc0->mdasp = CS0_END; /* CS addressing */
+
+ /* Step 3: Configure DDR type */
+ reg = (i->cs1_mirror << 19) | (i->walat << 16) | (i->bi_on << 12) |
+ (i->mif3_mode << 9) | (i->ralat << 6);
+ mmdc0->mdmisc = reg;
+
+ /* Step 4: Configure delay while leaving reset */
+ reg = (txpr << 16) | (i->sde_to_rst << 8) | (i->rst_to_cke << 0);
+ mmdc0->mdor = reg;
+
+ /* Step 5: Configure DDR physical parameters (density and burst len) */
+ reg = (m->rowaddr - 11) << 24 | /* ROW */
+ (m->coladdr - 9) << 20 | /* COL */
+ (1 << 19) | /* Burst Length = 8 for DDR3 */
+ (i->dsize << 16); /* DDR data bus size */
+ mmdc0->mdctl = reg;
+
+ /* Step 6: Perform ZQ calibration */
+ reg = (u32)0xa1390001; /* one-time HW ZQ calib */
+ mmdc0->mpzqhwctrl = reg;
+ if (i->dsize > 1)
+ mmdc1->mpzqhwctrl = reg;
+
+ /* Step 7: Enable MMDC with desired chip select */
+ reg = mmdc0->mdctl |
+ (1 << 31) | /* SDE_0 for CS0 */
+ ((i->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */
+ mmdc0->mdctl = reg;
+
+ /* Step 8: Write Mode Registers to Init DDR3 devices */
+ for (cs = 0; cs < i->ncs; cs++) {
+ /* MR2 */
+ reg = (i->rtt_wr & 3) << 9 | (m->SRT & 1) << 7 |
+ ((tcwl - 3) & 3) << 3;
+ mmdc0->mdscr = (u32)MR(reg, 2, 3, cs);
+ /* MR3 */
+ mmdc0->mdscr = (u32)MR(0, 3, 3, cs);
+ /* MR1 */
+ reg = ((i->rtt_nom & 1) ? 1 : 0) << 2 |
+ ((i->rtt_nom & 2) ? 1 : 0) << 6;
+ mmdc0->mdscr = (u32)MR(reg, 1, 3, cs);
+ reg = ((tcl - 1) << 4) | /* CAS */
+ (1 << 8) | /* DLL Reset */
+ ((twr - 3) << 9); /* Write Recovery */
+ /* MR0 */
+ mmdc0->mdscr = (u32)MR(reg, 0, 3, cs);
+ /* ZQ calibration */
+ reg = (1 << 10);
+ mmdc0->mdscr = (u32)MR(reg, 0, 4, cs);
+ }
+
+ /* Step 10: Power down control and self-refresh */
+ reg = (tcke & 0x7) << 16 |
+ 5 << 12 | /* PWDT_1: 256 cycles */
+ 5 << 8 | /* PWDT_0: 256 cycles */
+ 1 << 6 | /* BOTH_CS_PD */
+ (tcksrx & 0x7) << 3 |
+ (tcksre & 0x7);
+ mmdc0->mdpdc = reg;
+ mmdc0->mapsr = (u32)0x00011006; /* ADOPT power down enabled */
+
+ /* Step 11: Configure ZQ calibration: one-time and periodic 1ms */
+ mmdc0->mpzqhwctrl = (u32)0xa1390003;
+ if (i->dsize > 1)
+ mmdc1->mpzqhwctrl = (u32)0xa1390003;
+
+ /* Step 12: Configure and activate periodic refresh */
+ reg = (1 << 14) | /* REF_SEL: Periodic refresh cycles of 32kHz */
+ (7 << 11); /* REFR: Refresh Rate - 8 refreshes */
+ mmdc0->mdref = reg;
+
+ /* Step 13: Deassert config request - init complete */
+ mmdc0->mdscr = (u32)0x00000000;
+
+ /* wait for auto-ZQ calibration to complete */
+ mdelay(1);
+}
diff --git a/arch/arm/include/asm/arch-mx6/mx6-ddr.h b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
index c2a31d2..d544d2e 100644
--- a/arch/arm/include/asm/arch-mx6/mx6-ddr.h
+++ b/arch/arm/include/asm/arch-mx6/mx6-ddr.h
@@ -173,6 +173,78 @@ struct mx6sdl_iomux_grp_regs {
u32 res4;
u32 grp_b6ds;
};
+
+/* Device Information: Varies per DDR3 part number and speed grade */
+struct mx6_ddr3_cfg {
+ u16 mem_speed; /* ie 1600 for DDR3-1600 (800,1066,1333,1600) */
+ u8 density; /* chip density (Gb) (1,2,4,8) */
+ u8 width; /* bus width (bits) (4,8,16) */
+ u8 banks; /* number of banks */
+ u8 rowaddr; /* row address bits (11-16)*/
+ u8 coladdr; /* col address bits (9-12) */
+ u8 pagesz; /* page size (K) (1-2) */
+ u16 trcd; /* tRCD=tRP=CL (ns*100) */
+ u16 trcmin; /* tRC min (ns*100) */
+ u16 trasmin; /* tRAS min (ns*100) */
+ u8 SRT; /* self-refresh temperature: 0=normal, 1=extended */
+};
+
+/* System Information: Varies per board design, layout, and term choices */
+struct mx6_ddr_sysinfo {
+ u8 dsize; /* size of bus (in dwords: 0=16bit,1=32bit,2=64bit) */
+ u8 cs_density; /* density per chip select (Gb) */
+ u8 ncs; /* number chip selects used (1|2) */
+ char cs1_mirror;/* enable address mirror (0|1) */
+ char bi_on; /* Bank interleaving enable */
+ u8 rtt_nom; /* Rtt_Nom (DDR3_RTT_*) */
+ u8 rtt_wr; /* Rtt_Wr (DDR3_RTT_*) */
+ u8 ralat; /* Read Additional Latency (0-7) */
+ u8 walat; /* Write Additional Latency (0-3) */
+ u8 mif3_mode; /* Command prediction working mode */
+ u8 rst_to_cke; /* Time from SDE enable to CKE rise */
+ u8 sde_to_rst; /* Time from SDE enable until DDR reset# is high */
+};
+
+/*
+ * Board specific calibration:
+ * This includes write leveling calibration values as well as DQS gating
+ * and read/write delays. These values are board/layout/device specific.
+ * Freescale recommends using the i.MX6 DDR Stress Test Tool V1.0.2
+ * (DOC-96412) to determine these values over a range of boards and
+ * temperatures.
+ */
+struct mx6_mmdc_calibration {
+ /* write leveling calibration */
+ u32 p0_mpwldectrl0;
+ u32 p0_mpwldectrl1;
+ u32 p1_mpwldectrl0;
+ u32 p1_mpwldectrl1;
+ /* read DQS gating */
+ u32 p0_mpdgctrl0;
+ u32 p0_mpdgctrl1;
+ u32 p1_mpdgctrl0;
+ u32 p1_mpdgctrl1;
+ /* read delay */
+ u32 p0_mprddlctl;
+ u32 p1_mprddlctl;
+ /* write delay */
+ u32 p0_mpwrdlctl;
+ u32 p1_mpwrdlctl;
+};
+
+/* configure iomux (pinctl/padctl) */
+void mx6dq_dram_iocfg(unsigned width,
+ const struct mx6dq_iomux_ddr_regs *,
+ const struct mx6dq_iomux_grp_regs *);
+void mx6sdl_dram_iocfg(unsigned width,
+ const struct mx6sdl_iomux_ddr_regs *,
+ const struct mx6sdl_iomux_grp_regs *);
+
+/* configure mx6 mmdc registers */
+void mx6_dram_cfg(const struct mx6_ddr_sysinfo *,
+ const struct mx6_mmdc_calibration *,
+ const struct mx6_ddr3_cfg *);
+
#endif /* CONFIG_SPL_BUILD */
#define MX6_MMDC_P0_MDCTL 0x021b0000
--
1.8.3.2
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 05/11] imx: add comments and remove unused struct fields
2014-05-08 5:16 ` [U-Boot] [PATCH v3 05/11] imx: add comments and remove unused struct fields Tim Harvey
@ 2014-05-28 16:38 ` Nikita Kiryanov
0 siblings, 0 replies; 30+ messages in thread
From: Nikita Kiryanov @ 2014-05-28 16:38 UTC (permalink / raw)
To: u-boot
On 08/05/14 08:16, Tim Harvey wrote:
> Add comment block for the imx_ddr_size function and remove the extra unused
> fields from struct esd_mmdc_regs which are also not common between IMX53 and
> IMX6.
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> Acked-by: Stefano Babic <sbabic@denx.de>
> ---
> v3:
> - fixed doxygen-style comment block
> - added Stefano's Ack
>
> v2:
> - new patch in series
> ---
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL
2014-05-08 5:16 ` [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL Tim Harvey
@ 2014-05-28 16:38 ` Nikita Kiryanov
2014-05-29 4:11 ` Tim Harvey
0 siblings, 1 reply; 30+ messages in thread
From: Nikita Kiryanov @ 2014-05-28 16:38 UTC (permalink / raw)
To: u-boot
Hi Tim,
Sorry for the late reply.
On 08/05/14 08:16, Tim Harvey wrote:
> Add a common spl.c file to support boot device functions needed for SPL
> such as detecting the boot device.
>
> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
> ---
> v3:
> - added Freescale copyright
>
> v2:
> - re-base on top of Masahiro Yamada's consolidation patch:
> http://patchwork.ozlabs.org/patch/341817/
> - moved spl_boot_device() and get_boot_mode() into own common imx spl.c file
> - use mem-mapped structure for smbr reg access
> ---
[..snip..]
> + }
> + break;
> + /* SD/eSD: 8.5.3, Table 8-15 */
> + case 0x4:
> + case 0x5:
> + return BOOT_DEVICE_MMC1;
> + /* MMC/eMMC: 8.5.3 */
> + case 0x6:
> + case 0x7:
> + return BOOT_DEVICE_MMC1;
> + /* NAND Flash: 8.5.2 */
> + case 0x8 ... 0xf:
> + return BOOT_DEVICE_NAND;
> + }
> + return BOOT_DEVICE_NONE;
> +}
> +#endif
> +
> +#if defined(CONFIG_SPL_MMC_SUPPORT)
> +/* called from spl_mmc to see type of boot mode for storage (RAW or FAT) */
> +u32 spl_boot_mode(void)
> +{
> + switch (spl_boot_device()) {
> + /* for MMC return either RAW or FAT mode */
> + case BOOT_DEVICE_MMC1:
> + case BOOT_DEVICE_MMC2:
spl_boot_device() returns only BOOT_DEVICE_MMC1. Was the MMC/eMMC case
supposed to return a BOOT_DEVICE_MMC2?
Aside from this nitpick,
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers
2014-05-08 5:16 ` [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers Tim Harvey
@ 2014-05-28 17:06 ` Nikita Kiryanov
2014-05-29 4:16 ` Tim Harvey
0 siblings, 1 reply; 30+ messages in thread
From: Nikita Kiryanov @ 2014-05-28 17:06 UTC (permalink / raw)
To: u-boot
Hi Tim,
On 08/05/14 08:16, Tim Harvey wrote:
> Add memory-mapped structures for MMDC iomux and configuration. Note that
> the MMDC configuration registers are common between the IMX6DQ
> (IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) the iomux
> register addresses differ. This requires two sets of structures.
>
> Add structures to describe DDR3 device information, system information
> (memory layout, etc), and MMDC calibration regitsers that can be used to
> configure the MMDC dynamically.
s/regitsers/registers
>
> We define these structures for SPL builds instead of including mx6q-ddr.h an
> mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
> files.
What about the usefulness of the structs for U-Boot code? For example,
it might be necessary for U-Boot code to query the MMDC registers to
setup memory related variables like gd->ram_size and
gd->bd->bi_dram[i].size. Sure this can be done using the #defines
in the header files, but we lose nothing by making the structs
available to U-Boot as well.
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL
2014-05-28 16:38 ` Nikita Kiryanov
@ 2014-05-29 4:11 ` Tim Harvey
2014-05-29 6:45 ` Igor Grinberg
0 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-29 4:11 UTC (permalink / raw)
To: u-boot
On Wed, May 28, 2014 at 9:38 AM, Nikita Kiryanov <nikita@compulab.co.il> wrote:
> Hi Tim,
> Sorry for the late reply.
no worries - your the only review of this revision thus far ;)
>
>
> On 08/05/14 08:16, Tim Harvey wrote:
>>
>> Add a common spl.c file to support boot device functions needed for SPL
>> such as detecting the boot device.
>>
>> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
>> ---
>> v3:
>> - added Freescale copyright
>>
>> v2:
>> - re-base on top of Masahiro Yamada's consolidation patch:
>> http://patchwork.ozlabs.org/patch/341817/
>> - moved spl_boot_device() and get_boot_mode() into own common imx spl.c
>> file
>> - use mem-mapped structure for smbr reg access
>> ---
>
>
> [..snip..]
>
>
>> + }
>> + break;
>> + /* SD/eSD: 8.5.3, Table 8-15 */
>> + case 0x4:
>> + case 0x5:
>> + return BOOT_DEVICE_MMC1;
>> + /* MMC/eMMC: 8.5.3 */
>> + case 0x6:
>> + case 0x7:
>> + return BOOT_DEVICE_MMC1;
>> + /* NAND Flash: 8.5.2 */
>> + case 0x8 ... 0xf:
>> + return BOOT_DEVICE_NAND;
>> + }
>> + return BOOT_DEVICE_NONE;
>> +}
>> +#endif
>> +
>> +#if defined(CONFIG_SPL_MMC_SUPPORT)
>> +/* called from spl_mmc to see type of boot mode for storage (RAW or FAT)
>> */
>> +u32 spl_boot_mode(void)
>> +{
>> + switch (spl_boot_device()) {
>> + /* for MMC return either RAW or FAT mode */
>> + case BOOT_DEVICE_MMC1:
>> + case BOOT_DEVICE_MMC2:
>
>
> spl_boot_device() returns only BOOT_DEVICE_MMC1. Was the MMC/eMMC case
> supposed to return a BOOT_DEVICE_MMC2?
Its hard to say - I think the use of BOOT_DEVICE_* is very
implementation specific. I don't quite understand why there is a
BOOT_DEVICE_MMC{1,2,2_2} defined in arch/arm/include/asm/spl.h - the
BOOT_DEVICE_MMC2_2 is certainly quite odd. In uboot/common/spl/spl.c
they are all treated the same and spl_mmc_load_image() always assumes
the 'first' mmc device anyway.
In the IMX6 case I'm not sure an SD/uSD card would be treated any
different than an MMC card so it would come down to which specific
device is flagged as the boot device, of which there are 4 sdhc's. So
eventually, one might need to add more BOOT_DEVICE_MMC enums if that
is to be supported. For now, I'm keeping it simple and there is an
issue with IMX6 spl_mmc_load_image() anyway which I plan on addressing
later.
Tim
>
> Aside from this nitpick,
> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers
2014-05-28 17:06 ` Nikita Kiryanov
@ 2014-05-29 4:16 ` Tim Harvey
2014-05-29 6:48 ` Stefano Babic
0 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-29 4:16 UTC (permalink / raw)
To: u-boot
On Wed, May 28, 2014 at 10:06 AM, Nikita Kiryanov <nikita@compulab.co.il> wrote:
> Hi Tim,
>
>
> On 08/05/14 08:16, Tim Harvey wrote:
>>
>> Add memory-mapped structures for MMDC iomux and configuration. Note that
>> the MMDC configuration registers are common between the IMX6DQ
>> (IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) the iomux
>> register addresses differ. This requires two sets of structures.
>>
>> Add structures to describe DDR3 device information, system information
>> (memory layout, etc), and MMDC calibration regitsers that can be used to
>> configure the MMDC dynamically.
>
>
> s/regitsers/registers
thanks - will address in the next revision or in a following the
commit if we can ever get this series committed.
>
>
>>
>> We define these structures for SPL builds instead of including mx6q-ddr.h
>> an
>> mx6dl-ddr.h which use the same namespace and are only useful for imximage
>> cf
>> files.
>
>
> What about the usefulness of the structs for U-Boot code? For example,
> it might be necessary for U-Boot code to query the MMDC registers to
> setup memory related variables like gd->ram_size and
> gd->bd->bi_dram[i].size. Sure this can be done using the #defines
> in the header files, but we lose nothing by making the structs
> available to U-Boot as well.
>
perhaps, but I would assume if anyone needs these in u-boot they can
broaden the scope when needed. There is an imx_ddr_size() function in
spl/arch/arm/imx-common/cpu.c that returns dram size based on MMDC
configuration already, yet it uses a subset of this structure that is
common to imx in general.
Regards,
Tim
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL
2014-05-29 4:11 ` Tim Harvey
@ 2014-05-29 6:45 ` Igor Grinberg
0 siblings, 0 replies; 30+ messages in thread
From: Igor Grinberg @ 2014-05-29 6:45 UTC (permalink / raw)
To: u-boot
Hi Tim,
On 05/29/14 07:11, Tim Harvey wrote:
> On Wed, May 28, 2014 at 9:38 AM, Nikita Kiryanov <nikita@compulab.co.il> wrote:
>> Hi Tim,
>> Sorry for the late reply.
>
> no worries - your the only review of this revision thus far ;)
>
>>
>>
>> On 08/05/14 08:16, Tim Harvey wrote:
>>>
>>> Add a common spl.c file to support boot device functions needed for SPL
>>> such as detecting the boot device.
>>>
>>> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
>>> ---
>>> v3:
>>> - added Freescale copyright
>>>
>>> v2:
>>> - re-base on top of Masahiro Yamada's consolidation patch:
>>> http://patchwork.ozlabs.org/patch/341817/
>>> - moved spl_boot_device() and get_boot_mode() into own common imx spl.c
>>> file
>>> - use mem-mapped structure for smbr reg access
>>> ---
>>
>>
>> [..snip..]
>>
>>
>>> + }
>>> + break;
>>> + /* SD/eSD: 8.5.3, Table 8-15 */
>>> + case 0x4:
>>> + case 0x5:
>>> + return BOOT_DEVICE_MMC1;
>>> + /* MMC/eMMC: 8.5.3 */
>>> + case 0x6:
>>> + case 0x7:
>>> + return BOOT_DEVICE_MMC1;
>>> + /* NAND Flash: 8.5.2 */
>>> + case 0x8 ... 0xf:
>>> + return BOOT_DEVICE_NAND;
>>> + }
>>> + return BOOT_DEVICE_NONE;
>>> +}
>>> +#endif
>>> +
>>> +#if defined(CONFIG_SPL_MMC_SUPPORT)
>>> +/* called from spl_mmc to see type of boot mode for storage (RAW or FAT)
>>> */
>>> +u32 spl_boot_mode(void)
>>> +{
>>> + switch (spl_boot_device()) {
>>> + /* for MMC return either RAW or FAT mode */
>>> + case BOOT_DEVICE_MMC1:
>>> + case BOOT_DEVICE_MMC2:
>>
>>
>> spl_boot_device() returns only BOOT_DEVICE_MMC1. Was the MMC/eMMC case
>> supposed to return a BOOT_DEVICE_MMC2?
>
> Its hard to say - I think the use of BOOT_DEVICE_* is very
> implementation specific. I don't quite understand why there is a
> BOOT_DEVICE_MMC{1,2,2_2} defined in arch/arm/include/asm/spl.h - the
> BOOT_DEVICE_MMC2_2 is certainly quite odd.
AFAIK, this is needed to support eMMC boot partitions which are physical
and not logical, but they are still within the same device.
> In uboot/common/spl/spl.c
> they are all treated the same and spl_mmc_load_image() always assumes
> the 'first' mmc device anyway.
>
> In the IMX6 case I'm not sure an SD/uSD card would be treated any
> different than an MMC card so it would come down to which specific
> device is flagged as the boot device, of which there are 4 sdhc's. So
> eventually, one might need to add more BOOT_DEVICE_MMC enums if that
> is to be supported. For now, I'm keeping it simple and there is an
> issue with IMX6 spl_mmc_load_image() anyway which I plan on addressing
> later.
>
> Tim
>
>>
>> Aside from this nitpick,
>> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
--
Regards,
Igor.
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers
2014-05-29 4:16 ` Tim Harvey
@ 2014-05-29 6:48 ` Stefano Babic
2014-05-29 7:20 ` Nikita Kiryanov
0 siblings, 1 reply; 30+ messages in thread
From: Stefano Babic @ 2014-05-29 6:48 UTC (permalink / raw)
To: u-boot
Hi Tim,
On 29/05/2014 06:16, Tim Harvey wrote:
>>
>
> perhaps, but I would assume if anyone needs these in u-boot they can
> broaden the scope when needed.
Agree. At the moment, there is only one user of the structure and it is ok.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL
2014-05-08 5:16 ` [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL Tim Harvey
@ 2014-05-29 7:02 ` Stefano Babic
2014-05-30 4:52 ` Tim Harvey
0 siblings, 1 reply; 30+ messages in thread
From: Stefano Babic @ 2014-05-29 7:02 UTC (permalink / raw)
To: u-boot
Hi Tim,
I cannot build with this version. A setup for a couple of pins is not
yet replaces.
In fact, I have:
/* Enable Backlight */
imx_iomux_v3_setup_pad(MX6_PAD_SD1_CMD__GPIO1_IO18 |
and it should be:
SETUP_IOMUX_PAD(PAD_SD1_CMD__GPIO1_IO18 |
The same some lines later:
/* Backlight CABEN on LVDS connector */
- imx_iomux_v3_setup_pad(MX6_PAD_SD2_CLK__GPIO1_IO10 |
+ SETUP_IOMUX_PAD(PAD_SD2_CLK__GPIO1_IO10 |
Can you check and fix it ? Thanks !
Regarding your patchset: I had no remarkable comments and, as I have not
seen any comments from other developers, your patchset is ready to be
merged. I am also waiting for Masahiro's patch to be applied.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers
2014-05-29 6:48 ` Stefano Babic
@ 2014-05-29 7:20 ` Nikita Kiryanov
0 siblings, 0 replies; 30+ messages in thread
From: Nikita Kiryanov @ 2014-05-29 7:20 UTC (permalink / raw)
To: u-boot
On 29/05/14 09:48, Stefano Babic wrote:
> Hi Tim,
>
> On 29/05/2014 06:16, Tim Harvey wrote:
>
>>>
>>
>> perhaps, but I would assume if anyone needs these in u-boot they can
>> broaden the scope when needed.
>
> Agree. At the moment, there is only one user of the structure and it is ok.
>
> Best regards,
> Stefano Babic
>
Alright. Then:
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL
2014-05-29 7:02 ` Stefano Babic
@ 2014-05-30 4:52 ` Tim Harvey
2014-05-30 7:36 ` Stefano Babic
0 siblings, 1 reply; 30+ messages in thread
From: Tim Harvey @ 2014-05-30 4:52 UTC (permalink / raw)
To: u-boot
On Thu, May 29, 2014 at 12:02 AM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Tim,
>
> I cannot build with this version. A setup for a couple of pins is not
> yet replaces.
>
> In fact, I have:
>
> /* Enable Backlight */
> imx_iomux_v3_setup_pad(MX6_PAD_SD1_CMD__GPIO1_IO18 |
>
> and it should be:
>
> SETUP_IOMUX_PAD(PAD_SD1_CMD__GPIO1_IO18 |
>
> The same some lines later:
>
> /* Backlight CABEN on LVDS connector */
> - imx_iomux_v3_setup_pad(MX6_PAD_SD2_CLK__GPIO1_IO10 |
> + SETUP_IOMUX_PAD(PAD_SD2_CLK__GPIO1_IO10 |
>
>
> Can you check and fix it ? Thanks !
>
> Regarding your patchset: I had no remarkable comments and, as I have not
> seen any comments from other developers, your patchset is ready to be
> merged. I am also waiting for Masahiro's patch to be applied.
>
> Best regards,
> Stefano Babic
>
Stefano,
Those should be patched from patch 10. However, I can't seem to get
patch 9 to apply cleanly from current u-boot-imx/master so perhaps I
should just rebase the whole series and post again?
Tim
^ permalink raw reply [flat|nested] 30+ messages in thread
* [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL
2014-05-30 4:52 ` Tim Harvey
@ 2014-05-30 7:36 ` Stefano Babic
0 siblings, 0 replies; 30+ messages in thread
From: Stefano Babic @ 2014-05-30 7:36 UTC (permalink / raw)
To: u-boot
Hi Tim,
On 30/05/2014 06:52, Tim Harvey wrote:
> On Thu, May 29, 2014 at 12:02 AM, Stefano Babic <sbabic@denx.de> wrote:
>> Hi Tim,
>>
>> I cannot build with this version. A setup for a couple of pins is not
>> yet replaces.
>>
>> In fact, I have:
>>
>> /* Enable Backlight */
>> imx_iomux_v3_setup_pad(MX6_PAD_SD1_CMD__GPIO1_IO18 |
>>
>> and it should be:
>>
>> SETUP_IOMUX_PAD(PAD_SD1_CMD__GPIO1_IO18 |
>>
>> The same some lines later:
>>
>> /* Backlight CABEN on LVDS connector */
>> - imx_iomux_v3_setup_pad(MX6_PAD_SD2_CLK__GPIO1_IO10 |
>> + SETUP_IOMUX_PAD(PAD_SD2_CLK__GPIO1_IO10 |
>>
>>
>> Can you check and fix it ? Thanks !
>>
>> Regarding your patchset: I had no remarkable comments and, as I have not
>> seen any comments from other developers, your patchset is ready to be
>> merged. I am also waiting for Masahiro's patch to be applied.
>>
>> Best regards,
>> Stefano Babic
>>
>
> Stefano,
>
> Those should be patched from patch 10.
Sure ? Patch 10 replaces a lot of occurrencies, but I do not see the
ones introduced by "imx: ventana: add HDMI and LVDS display capability"
that is already applied.
> However, I can't seem to get
> patch 9 to apply cleanly from current u-boot-imx/master so perhaps I
> should just rebase the whole series and post again?
Please take a look and repost if required. If you repost, you could also
fix yourself this styling issue in Patch 3:
ERROR: return is not a function, parentheses are not required
#192: FILE: drivers/mtd/nand/mxs_nand_spl.c:138:
+ return (chip->oob_poi[0] != 0xff);
Regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 30+ messages in thread
end of thread, other threads:[~2014-05-30 7:36 UTC | newest]
Thread overview: 30+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-05-08 5:16 [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 01/11] nand: remove CONFIG_SYS_NAND_PAGE_SIZE Tim Harvey
2014-05-14 8:52 ` Masahiro Yamada
2014-05-14 10:14 ` Stefano Babic
2014-05-15 8:31 ` Stefano Babic
2014-05-08 5:16 ` [U-Boot] [PATCH v3 02/11] spl: nand: add support for mxs nand Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 03/11] mx6: add common SPL configuration Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 04/11] mx6: add boot device support for SPL Tim Harvey
2014-05-28 16:38 ` Nikita Kiryanov
2014-05-29 4:11 ` Tim Harvey
2014-05-29 6:45 ` Igor Grinberg
2014-05-08 5:16 ` [U-Boot] [PATCH v3 05/11] imx: add comments and remove unused struct fields Tim Harvey
2014-05-28 16:38 ` Nikita Kiryanov
2014-05-08 5:16 ` [U-Boot] [PATCH v3 06/11] mx6: add structs for mmdc and ddr iomux registers Tim Harvey
2014-05-28 17:06 ` Nikita Kiryanov
2014-05-29 4:16 ` Tim Harvey
2014-05-29 6:48 ` Stefano Babic
2014-05-29 7:20 ` Nikita Kiryanov
2014-05-08 5:16 ` [U-Boot] [PATCH v3 07/11] mx6: add mmdc configuration for MX6Q/MX6DL Tim Harvey
2014-05-22 22:28 ` [U-Boot] [PATCH v4 " Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 08/11] imx: iomux: add macros to setup iomux for multiple SoC types Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 09/11] imx: ventana: split read_eeprom into standalone file Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 10/11] imx: ventana: auto-configure for IMX6Q vs IMX6DL Tim Harvey
2014-05-08 5:16 ` [U-Boot] [PATCH v3 11/11] imx: ventana: switch to SPL Tim Harvey
2014-05-29 7:02 ` Stefano Babic
2014-05-30 4:52 ` Tim Harvey
2014-05-30 7:36 ` Stefano Babic
2014-05-22 6:14 ` [U-Boot] [PATCH v3 00/11] mx6: SPL NAND support Tim Harvey
2014-05-22 6:34 ` Stefano Babic
2014-05-22 22:17 ` Tim Harvey
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.