[U-Boot] [PATCH v7 1/1] ARM: kirkwood: add mvsdio driver

* [U-Boot] [PATCH v7 1/1] ARM: kirkwood: add mvsdio driver
@ 2014-07-25 19:07 Gerald Kerma
  2014-07-26 11:54 ` Stefan Roese
  0 siblings, 1 reply; 6+ messages in thread
From: Gerald Kerma @ 2014-07-25 19:07 UTC (permalink / raw)
  To: u-boot

This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.

Signed-off-by: Gerald Kerma <drEagle@doukki.net>
---

 Changes in v7:
 - removed unrelated stuff
 - minor code cleaning

 Changes in v6:
 - rename driver to mvebu_mmc
 - renames constants and functions
 - move mmc_init to kirkwood/cpu
 - code cleaning

 Changes in v5:
 - purge uneeded code
 - remove some extra debug

 Changes in v4:
 - rename drivers files to MVSDIO
 - fix MMC clock init which now use dev ID
 - clean debug strings
 - remove MVSDIO_TWEAK_NOSDHS quirk
 - remove dead code

 Changes in v3:
 - Add MVSDIO_TWEAK_NOSDHS quirk
 - Minor clean

 Changes in v2:
 - Fix some typo and missing lines from patch import

 arch/arm/cpu/arm926ejs/kirkwood/cpu.c         |   9 +
 arch/arm/include/asm/arch-kirkwood/kirkwood.h |   1 +
 drivers/mmc/Makefile                          |   1 +
 drivers/mmc/mvebu_mmc.c                       | 361 ++++++++++++++++++++++++++
 include/configs/openrd.h                      |   8 +
 include/configs/sheevaplug.h                  |  11 +
 include/mvebu_mmc.h                           | 278 ++++++++++++++++++++
 7 files changed, 669 insertions(+)
 create mode 100644 drivers/mmc/mvebu_mmc.c
 create mode 100644 include/mvebu_mmc.h

diff --git a/arch/arm/cpu/arm926ejs/kirkwood/cpu.c b/arch/arm/cpu/arm926ejs/kirkwood/cpu.c
index da80240..881e2de 100644
--- a/arch/arm/cpu/arm926ejs/kirkwood/cpu.c
+++ b/arch/arm/cpu/arm926ejs/kirkwood/cpu.c
@@ -13,6 +13,7 @@
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/kirkwood.h>
+#include <mvebu_mmc.h>
 
 #define BUFLEN	16
 
@@ -377,3 +378,11 @@ int cpu_eth_init(bd_t *bis)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_MVEBU_MMC
+int board_mmc_init(bd_t *bis)
+{
+	mvebu_mmc_init(bis);
+	return 0;
+}
+#endif /* CONFIG_MVEBU_MMC */
diff --git a/arch/arm/include/asm/arch-kirkwood/kirkwood.h b/arch/arm/include/asm/arch-kirkwood/kirkwood.h
index bc207f5..3ea51d7 100644
--- a/arch/arm/include/asm/arch-kirkwood/kirkwood.h
+++ b/arch/arm/include/asm/arch-kirkwood/kirkwood.h
@@ -39,6 +39,7 @@
 #define KW_EGIGA0_BASE			(KW_REGISTER(0x72000))
 #define KW_EGIGA1_BASE			(KW_REGISTER(0x76000))
 #define KW_SATA_BASE			(KW_REGISTER(0x80000))
+#define KW_SDIO_BASE			(KW_REGISTER(0x90000))
 
 /* Kirkwood Sata controller has two ports */
 #define KW_SATA_PORT0_OFFSET		0x2000
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index 34febf5..f5be96f 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -37,3 +37,4 @@ obj-$(CONFIG_SPL_MMC_BOOT) += fsl_esdhc_spl.o
 else
 obj-$(CONFIG_GENERIC_MMC) += mmc_write.o
 endif
+obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o
diff --git a/drivers/mmc/mvebu_mmc.c b/drivers/mmc/mvebu_mmc.c
new file mode 100644
index 0000000..9759198
--- /dev/null
+++ b/drivers/mmc/mvebu_mmc.c
@@ -0,0 +1,361 @@
+/*
+ * Marvell MMC/SD/SDIO driver
+ *
+ * (C) Copyright 2012
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Maen Suleiman, Gerald Kerma
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <part.h>
+#include <mmc.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <mvebu_mmc.h>
+
+#define DRIVER_NAME "MVEBU_MMC"
+
+static void mvebu_mmc_write(u32 offs, u32 val)
+{
+	writel(val, CONFIG_SYS_MMC_BASE + (offs));
+}
+
+static u32 mvebu_mmc_read(u32 offs)
+{
+	return readl(CONFIG_SYS_MMC_BASE + (offs));
+}
+
+static int mvebu_mmc_setup_data(struct mmc_data *data)
+{
+	u32 ctrl_reg;
+
+	debug("%s, data %s : blocks=%d blksz=%d\n", DRIVER_NAME,
+	      (data->flags & MMC_DATA_READ) ? "read" : "write",
+	      data->blocks, data->blocksize);
+
+	/* default to maximum timeout */
+	ctrl_reg = mvebu_mmc_read(SDIO_HOST_CTRL);
+	ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
+	mvebu_mmc_write(SDIO_HOST_CTRL, ctrl_reg);
+
+	if (data->flags & MMC_DATA_READ) {
+		mvebu_mmc_write(SDIO_SYS_ADDR_LOW, (u32)data->dest & 0xffff);
+		mvebu_mmc_write(SDIO_SYS_ADDR_HI, (u32)data->dest >> 16);
+	} else {
+		mvebu_mmc_write(SDIO_SYS_ADDR_LOW, (u32)data->src & 0xffff);
+		mvebu_mmc_write(SDIO_SYS_ADDR_HI, (u32)data->src >> 16);
+	}
+
+	mvebu_mmc_write(SDIO_BLK_COUNT, data->blocks);
+	mvebu_mmc_write(SDIO_BLK_SIZE, data->blocksize);
+
+	return 0;
+}
+
+static int mvebu_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
+			      struct mmc_data *data)
+{
+	int timeout = 10;
+	ushort waittype = 0;
+	ushort resptype = 0;
+	ushort xfertype = 0;
+	ushort resp_indx = 0;
+
+	debug("cmdidx [0x%x] resp_type[0x%x] cmdarg[0x%x]\n",
+	      cmd->cmdidx, cmd->resp_type, cmd->cmdarg);
+
+	udelay(10*1000);
+
+	debug("%s: cmd %d (hw state 0x%04x)\n", DRIVER_NAME,
+	      cmd->cmdidx, mvebu_mmc_read(SDIO_HW_STATE));
+
+	/* Checking if card is busy */
+	while ((mvebu_mmc_read(SDIO_HW_STATE) & CARD_BUSY)) {
+		if (timeout == 0) {
+			printf("%s: card busy!\n", DRIVER_NAME);
+			return -1;
+		}
+		timeout--;
+		udelay(1000);
+	}
+
+	/* Set up for a data transfer if we have one */
+	if (data) {
+		int err = mvebu_mmc_setup_data(data);
+
+		if (err)
+			return err;
+	}
+
+	resptype = SDIO_CMD_INDEX(cmd->cmdidx);
+
+	/* Analyzing resptype/xfertype/waittype for the command */
+	if (cmd->resp_type & MMC_RSP_BUSY)
+		resptype |= SDIO_CMD_RSP_48BUSY;
+	else if (cmd->resp_type & MMC_RSP_136)
+		resptype |= SDIO_CMD_RSP_136;
+	else if (cmd->resp_type & MMC_RSP_PRESENT)
+		resptype |= SDIO_CMD_RSP_48;
+	else
+		resptype |= SDIO_CMD_RSP_NONE;
+
+	if (cmd->resp_type & MMC_RSP_CRC)
+		resptype |= SDIO_CMD_CHECK_CMDCRC;
+
+	if (cmd->resp_type & MMC_RSP_OPCODE)
+		resptype |= SDIO_CMD_INDX_CHECK;
+
+	if (cmd->resp_type & MMC_RSP_PRESENT) {
+		resptype |= SDIO_UNEXPECTED_RESP;
+		waittype |= SDIO_NOR_UNEXP_RSP;
+	}
+
+	if (data) {
+		resptype |= SDIO_CMD_DATA_PRESENT | SDIO_CMD_CHECK_DATACRC16;
+		xfertype |= SDIO_XFER_MODE_HW_WR_DATA_EN;
+		if (data->flags & MMC_DATA_READ) {
+			xfertype |= SDIO_XFER_MODE_TO_HOST;
+			waittype = SDIO_NOR_DMA_INI;
+		} else {
+			waittype |= SDIO_NOR_XFER_DONE;
+		}
+	} else {
+		waittype |= SDIO_NOR_CMD_DONE;
+	}
+
+	/* Setting cmd arguments */
+	mvebu_mmc_write(SDIO_ARG_LOW, cmd->cmdarg & 0xffff);
+	mvebu_mmc_write(SDIO_ARG_HI, cmd->cmdarg >> 16);
+
+	/* Setting Xfer mode */
+	mvebu_mmc_write(SDIO_XFER_MODE, xfertype);
+
+	mvebu_mmc_write(SDIO_NOR_INTR_STATUS, ~SDIO_NOR_CARD_INT);
+	mvebu_mmc_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
+
+	/* Sending command */
+	mvebu_mmc_write(SDIO_CMD, resptype);
+
+	mvebu_mmc_write(SDIO_NOR_INTR_EN, SDIO_POLL_MASK);
+	mvebu_mmc_write(SDIO_ERR_INTR_EN, SDIO_POLL_MASK);
+
+	/* Waiting for completion */
+	timeout = 1000000;
+
+	while (!((mvebu_mmc_read(SDIO_NOR_INTR_STATUS)) & waittype)) {
+		if (mvebu_mmc_read(SDIO_NOR_INTR_STATUS) & SDIO_NOR_ERROR) {
+			debug("%s: error! cmdidx : %d, err reg: %04x\n",
+			      DRIVER_NAME, cmd->cmdidx,
+			      mvebu_mmc_read(SDIO_ERR_INTR_STATUS));
+			if (mvebu_mmc_read(SDIO_ERR_INTR_STATUS) &
+				(SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT))
+				return TIMEOUT;
+			return COMM_ERR;
+		}
+
+		timeout--;
+		udelay(1);
+		if (timeout <= 0) {
+			printf("%s: command timed out\n", DRIVER_NAME);
+			return TIMEOUT;
+		}
+	}
+
+	/* Handling response */
+	if (cmd->resp_type & MMC_RSP_136) {
+		uint response[8];
+
+		for (resp_indx = 0; resp_indx < 8; resp_indx++)
+			response[resp_indx]
+				= mvebu_mmc_read(SDIO_RSP(resp_indx));
+
+		cmd->response[0] =	((response[0] & 0x03ff) << 22) |
+					((response[1] & 0xffff) << 6) |
+					((response[2] & 0xfc00) >> 10);
+		cmd->response[1] =	((response[2] & 0x03ff) << 22) |
+					((response[3] & 0xffff) << 6) |
+					((response[4] & 0xfc00) >> 10);
+		cmd->response[2] =	((response[4] & 0x03ff) << 22) |
+					((response[5] & 0xffff) << 6) |
+					((response[6] & 0xfc00) >> 10);
+		cmd->response[3] =	((response[6] & 0x03ff) << 22) |
+					((response[7] & 0x3fff) << 8);
+	} else if (cmd->resp_type & MMC_RSP_PRESENT) {
+		uint response[3];
+
+		for (resp_indx = 0; resp_indx < 3; resp_indx++)
+			response[resp_indx]
+				= mvebu_mmc_read(SDIO_RSP(resp_indx));
+
+		cmd->response[0] =	((response[2] & 0x003f) << (8 - 8)) |
+					((response[1] & 0xffff) << (14 - 8)) |
+					((response[0] & 0x03ff) << (30 - 8));
+		cmd->response[1] =	((response[0] & 0xfc00) >> 10);
+		cmd->response[2] =	0;
+		cmd->response[3] =	0;
+	}
+
+	debug("%s: resp[0x%x] ", DRIVER_NAME, cmd->resp_type);
+	debug("[0x%x] ", cmd->response[0]);
+	debug("[0x%x] ", cmd->response[1]);
+	debug("[0x%x] ", cmd->response[2]);
+	debug("[0x%x] ", cmd->response[3]);
+	debug("\n");
+
+	return 0;
+}
+
+static void mvebu_mmc_power_up(void)
+{
+	debug("%s: power up\n", DRIVER_NAME);
+
+	/* disable interrupts */
+	mvebu_mmc_write(SDIO_NOR_INTR_EN, 0);
+	mvebu_mmc_write(SDIO_ERR_INTR_EN, 0);
+
+	/* SW reset */
+	mvebu_mmc_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
+
+	mvebu_mmc_write(SDIO_XFER_MODE, 0);
+
+	/* enable status */
+	mvebu_mmc_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK);
+	mvebu_mmc_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK);
+
+	/* enable interrupts status */
+	mvebu_mmc_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK);
+	mvebu_mmc_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK);
+}
+
+static void mvebu_mmc_set_clk(unsigned int clock)
+{
+	unsigned int m;
+
+	if (clock == 0) {
+		debug("%s: clock off\n", DRIVER_NAME);
+		mvebu_mmc_write(SDIO_XFER_MODE, SDIO_XFER_MODE_STOP_CLK);
+		mvebu_mmc_write(SDIO_CLK_DIV, MVEBU_MMC_BASE_DIV_MAX);
+	} else {
+		m = MVEBU_MMC_BASE_FAST_CLOCK/(2*clock) - 1;
+		if (m > MVEBU_MMC_BASE_DIV_MAX)
+			m = MVEBU_MMC_BASE_DIV_MAX;
+		mvebu_mmc_write(SDIO_CLK_DIV, m & MVEBU_MMC_BASE_DIV_MAX);
+	}
+
+	udelay(10*1000);
+}
+
+static void mvebu_mmc_set_bus(unsigned int bus)
+{
+	u32 ctrl_reg = 0;
+
+	ctrl_reg = mvebu_mmc_read(SDIO_HOST_CTRL);
+	ctrl_reg &= ~SDIO_HOST_CTRL_DATA_WIDTH_4_BITS;
+
+	switch (bus) {
+	case 4:
+		ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_4_BITS;
+		break;
+	case 1:
+	default:
+		ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_1_BIT;
+	}
+
+	/* default transfer mode */
+	ctrl_reg |= SDIO_HOST_CTRL_BIG_ENDIAN;
+	ctrl_reg &= ~SDIO_HOST_CTRL_LSB_FIRST;
+
+	/* default to maximum timeout */
+	ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX);
+
+	ctrl_reg |= SDIO_HOST_CTRL_PUSH_PULL_EN;
+
+	ctrl_reg |= SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY;
+
+	debug("%s: ctrl 0x%04x: %s %s %s\n", DRIVER_NAME, ctrl_reg,
+	      (ctrl_reg & SDIO_HOST_CTRL_PUSH_PULL_EN) ?
+	      "push-pull" : "open-drain",
+	      (ctrl_reg & SDIO_HOST_CTRL_DATA_WIDTH_4_BITS) ?
+	      "4bit-width" : "1bit-width",
+	      (ctrl_reg & SDIO_HOST_CTRL_HI_SPEED_EN) ?
+	      "high-speed" : "");
+
+	mvebu_mmc_write(SDIO_HOST_CTRL, ctrl_reg);
+	udelay(10*1000);
+}
+
+static void mvebu_mmc_set_ios(struct mmc *mmc)
+{
+	debug("%s: bus[%d] clock[%d]\n", DRIVER_NAME,
+	      mmc->bus_width, mmc->clock);
+	mvebu_mmc_set_bus(mmc->bus_width);
+	mvebu_mmc_set_clk(mmc->clock);
+}
+
+static int mvebu_mmc_initialize(struct mmc *mmc)
+{
+	debug("%s: mvebu_mmc_initialize", DRIVER_NAME);
+
+	/*
+	 * Setting host parameters
+	 * Initial Host Ctrl : Timeout : max , Normal Speed mode,
+	 * 4-bit data mode, Big Endian, SD memory Card, Push_pull CMD Line
+	 */
+	mvebu_mmc_write(SDIO_HOST_CTRL,
+			SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX) |
+			SDIO_HOST_CTRL_DATA_WIDTH_4_BITS |
+			SDIO_HOST_CTRL_BIG_ENDIAN |
+			SDIO_HOST_CTRL_PUSH_PULL_EN |
+			SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY);
+
+	mvebu_mmc_write(SDIO_CLK_CTRL, 0);
+
+	/* enable status */
+	mvebu_mmc_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK);
+	mvebu_mmc_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK);
+
+	/* disable interrupts */
+	mvebu_mmc_write(SDIO_NOR_INTR_EN, 0);
+	mvebu_mmc_write(SDIO_ERR_INTR_EN, 0);
+
+	/* SW reset */
+	mvebu_mmc_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW);
+
+	udelay(10*1000);
+
+	return 0;
+}
+
+static const struct mmc_ops mvebu_mmc_ops = {
+	.send_cmd	= mvebu_mmc_send_cmd,
+	.set_ios	= mvebu_mmc_set_ios,
+	.init		= mvebu_mmc_initialize,
+};
+
+static struct mmc_config mvebu_mmc_cfg = {
+	.name		= DRIVER_NAME,
+	.ops		= &mvebu_mmc_ops,
+	.f_min		= MVEBU_MMC_BASE_FAST_CLOCK / MVEBU_MMC_BASE_DIV_MAX,
+	.f_max		= MVEBU_MMC_CLOCKRATE_MAX,
+	.voltages	= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.host_caps	= MMC_MODE_4BIT | MMC_MODE_HS,
+	.part_type	= PART_TYPE_DOS,
+	.b_max		= CONFIG_SYS_MMC_MAX_BLK_COUNT,
+};
+
+int mvebu_mmc_init(bd_t *bis)
+{
+	struct mmc *mmc;
+
+	mvebu_mmc_power_up();
+
+	mmc = mmc_create(&mvebu_mmc_cfg, bis);
+	if (mmc == NULL)
+		return -1;
+
+	return 0;
+}
diff --git a/include/configs/openrd.h b/include/configs/openrd.h
index 8fab6e6..3eb408f 100644
--- a/include/configs/openrd.h
+++ b/include/configs/openrd.h
@@ -49,6 +49,7 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_USB
@@ -123,4 +124,11 @@
 #define CONFIG_SYS_ATA_IDE1_OFFSET	MV_SATA_PORT1_OFFSET
 #endif /*CONFIG_MVSATA_IDE*/
 
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MVEBU_MMC
+#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
+#endif /* CONFIG_CMD_MMC */
+
 #endif /* _CONFIG_OPENRD_BASE_H */
diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h
index ecc93bc..3d6ff09 100644
--- a/include/configs/sheevaplug.h
+++ b/include/configs/sheevaplug.h
@@ -31,6 +31,7 @@
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_MMC
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_USB
@@ -82,6 +83,16 @@
 #endif /* CONFIG_CMD_NET */
 
 /*
+ * SDIO/MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MVEBU_MMC
+#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
+#endif /* CONFIG_CMD_MMC */
+
+/*
  * File system
  */
 #define CONFIG_CMD_EXT2
diff --git a/include/mvebu_mmc.h b/include/mvebu_mmc.h
new file mode 100644
index 0000000..28d98fe
--- /dev/null
+++ b/include/mvebu_mmc.h
@@ -0,0 +1,278 @@
+/*
+ * Marvell MMC/SD/SDIO driver
+ *
+ * (C) Copyright 2012
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Maen Suleiman, Gerald Kerma
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MVEBU_MMC_H__
+#define __MVEBU_MMC_H__
+
+/* needed for the mmc_cfg definition */
+#include <mmc.h>
+
+#define MMC_BLOCK_SIZE				512
+
+/*
+ * Clock rates
+ */
+
+#define MVEBU_MMC_CLOCKRATE_MAX			50000000
+#define MVEBU_MMC_BASE_DIV_MAX			0x7ff
+#define MVEBU_MMC_BASE_FAST_CLOCK		CONFIG_SYS_TCLK
+#define MVEBU_MMC_BASE_FAST_CLK_100		100000000
+#define MVEBU_MMC_BASE_FAST_CLK_200		200000000
+
+/* SDIO register */
+#define SDIO_SYS_ADDR_LOW			0x000
+#define SDIO_SYS_ADDR_HI			0x004
+#define SDIO_BLK_SIZE				0x008
+#define SDIO_BLK_COUNT				0x00c
+#define SDIO_ARG_LOW				0x010
+#define SDIO_ARG_HI				0x014
+#define SDIO_XFER_MODE				0x018
+#define SDIO_CMD				0x01c
+#define SDIO_RSP(i)				(0x020 + ((i)<<2))
+#define SDIO_RSP0				0x020
+#define SDIO_RSP1				0x024
+#define SDIO_RSP2				0x028
+#define SDIO_RSP3				0x02c
+#define SDIO_RSP4				0x030
+#define SDIO_RSP5				0x034
+#define SDIO_RSP6				0x038
+#define SDIO_RSP7				0x03c
+#define SDIO_BUF_DATA_PORT			0x040
+#define SDIO_RSVED				0x044
+#define SDIO_HW_STATE				0x048
+#define SDIO_PRESENT_STATE0			0x048
+#define SDIO_PRESENT_STATE1			0x04c
+#define SDIO_HOST_CTRL				0x050
+#define SDIO_BLK_GAP_CTRL			0x054
+#define SDIO_CLK_CTRL				0x058
+#define SDIO_SW_RESET				0x05c
+#define SDIO_NOR_INTR_STATUS			0x060
+#define SDIO_ERR_INTR_STATUS			0x064
+#define SDIO_NOR_STATUS_EN			0x068
+#define SDIO_ERR_STATUS_EN			0x06c
+#define SDIO_NOR_INTR_EN			0x070
+#define SDIO_ERR_INTR_EN			0x074
+#define SDIO_AUTOCMD12_ERR_STATUS		0x078
+#define SDIO_CURR_BYTE_LEFT			0x07c
+#define SDIO_CURR_BLK_LEFT			0x080
+#define SDIO_AUTOCMD12_ARG_LOW			0x084
+#define SDIO_AUTOCMD12_ARG_HI			0x088
+#define SDIO_AUTOCMD12_INDEX			0x08c
+#define SDIO_AUTO_RSP(i)			(0x090 + ((i)<<2))
+#define SDIO_AUTO_RSP0				0x090
+#define SDIO_AUTO_RSP1				0x094
+#define SDIO_AUTO_RSP2				0x098
+#define SDIO_CLK_DIV				0x128
+
+#define WINDOW_CTRL(i)				(0x108 + ((i) << 3))
+#define WINDOW_BASE(i)				(0x10c + ((i) << 3))
+
+/* SDIO_PRESENT_STATE */
+#define CARD_BUSY				(1 << 1)
+#define CMD_INHIBIT				(1 << 0)
+#define CMD_TXACTIVE				(1 << 8)
+#define CMD_RXACTIVE				(1 << 9)
+#define CMD_AUTOCMD12ACTIVE			(1 << 14)
+#define CMD_BUS_BUSY				(CMD_AUTOCMD12ACTIVE |	\
+						CMD_RXACTIVE |	\
+						CMD_TXACTIVE |	\
+						CMD_INHIBIT |	\
+						CARD_BUSY)
+
+/*
+ * SDIO_CMD
+ */
+
+#define SDIO_CMD_RSP_NONE			(0 << 0)
+#define SDIO_CMD_RSP_136			(1 << 0)
+#define SDIO_CMD_RSP_48				(2 << 0)
+#define SDIO_CMD_RSP_48BUSY			(3 << 0)
+
+#define SDIO_CMD_CHECK_DATACRC16		(1 << 2)
+#define SDIO_CMD_CHECK_CMDCRC			(1 << 3)
+#define SDIO_CMD_INDX_CHECK			(1 << 4)
+#define SDIO_CMD_DATA_PRESENT			(1 << 5)
+#define SDIO_UNEXPECTED_RESP			(1 << 7)
+
+#define SDIO_CMD_INDEX(x)			((x) << 8)
+
+/*
+ * SDIO_XFER_MODE
+ */
+
+#define SDIO_XFER_MODE_STOP_CLK			(1 << 5)
+#define SDIO_XFER_MODE_HW_WR_DATA_EN		(1 << 1)
+#define SDIO_XFER_MODE_AUTO_CMD12		(1 << 2)
+#define SDIO_XFER_MODE_INT_CHK_EN		(1 << 3)
+#define SDIO_XFER_MODE_TO_HOST			(1 << 4)
+#define SDIO_XFER_MODE_DMA			(0 << 6)
+
+/*
+ * SDIO_HOST_CTRL
+ */
+
+#define SDIO_HOST_CTRL_PUSH_PULL_EN		(1 << 0)
+
+#define SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY	(0 << 1)
+#define SDIO_HOST_CTRL_CARD_TYPE_IO_ONLY	(1 << 1)
+#define SDIO_HOST_CTRL_CARD_TYPE_IO_MEM_COMBO	(2 << 1)
+#define SDIO_HOST_CTRL_CARD_TYPE_IO_MMC		(3 << 1)
+#define SDIO_HOST_CTRL_CARD_TYPE_MASK		(3 << 1)
+
+#define SDIO_HOST_CTRL_BIG_ENDIAN		(1 << 3)
+#define SDIO_HOST_CTRL_LSB_FIRST		(1 << 4)
+#define SDIO_HOST_CTRL_DATA_WIDTH_1_BIT		(0 << 9)
+#define SDIO_HOST_CTRL_DATA_WIDTH_4_BITS	(1 << 9)
+#define SDIO_HOST_CTRL_HI_SPEED_EN		(1 << 10)
+
+#define SDIO_HOST_CTRL_TMOUT_MAX		0xf
+#define SDIO_HOST_CTRL_TMOUT_MASK		(0xf << 11)
+#define SDIO_HOST_CTRL_TMOUT(x)			((x) << 11)
+#define SDIO_HOST_CTRL_TMOUT_EN			(1 << 15)
+
+/*
+ * SDIO_SW_RESET
+ */
+
+#define SDIO_SW_RESET_NOW			(1 << 8)
+
+/*
+ * Normal interrupt status bits
+ */
+
+#define SDIO_NOR_ERROR				(1 << 15)
+#define SDIO_NOR_UNEXP_RSP			(1 << 14)
+#define SDIO_NOR_AUTOCMD12_DONE			(1 << 13)
+#define SDIO_NOR_SUSPEND_ON			(1 << 12)
+#define SDIO_NOR_LMB_FF_8W_AVAIL		(1 << 11)
+#define SDIO_NOR_LMB_FF_8W_FILLED		(1 << 10)
+#define SDIO_NOR_READ_WAIT_ON			(1 << 9)
+#define SDIO_NOR_CARD_INT			(1 << 8)
+#define SDIO_NOR_READ_READY			(1 << 5)
+#define SDIO_NOR_WRITE_READY			(1 << 4)
+#define SDIO_NOR_DMA_INI			(1 << 3)
+#define SDIO_NOR_BLK_GAP_EVT			(1 << 2)
+#define SDIO_NOR_XFER_DONE			(1 << 1)
+#define SDIO_NOR_CMD_DONE			(1 << 0)
+
+/*
+ * Error status bits
+ */
+
+#define SDIO_ERR_CRC_STATUS			(1 << 14)
+#define SDIO_ERR_CRC_STARTBIT			(1 << 13)
+#define SDIO_ERR_CRC_ENDBIT			(1 << 12)
+#define SDIO_ERR_RESP_TBIT			(1 << 11)
+#define SDIO_ERR_XFER_SIZE			(1 << 10)
+#define SDIO_ERR_CMD_STARTBIT			(1 << 9)
+#define SDIO_ERR_AUTOCMD12			(1 << 8)
+#define SDIO_ERR_DATA_ENDBIT			(1 << 6)
+#define SDIO_ERR_DATA_CRC			(1 << 5)
+#define SDIO_ERR_DATA_TIMEOUT			(1 << 4)
+#define SDIO_ERR_CMD_INDEX			(1 << 3)
+#define SDIO_ERR_CMD_ENDBIT			(1 << 2)
+#define SDIO_ERR_CMD_CRC			(1 << 1)
+#define SDIO_ERR_CMD_TIMEOUT			(1 << 0)
+/* enable all for polling */
+#define SDIO_POLL_MASK				0xffff
+
+/*
+ * CMD12 error status bits
+ */
+
+#define SDIO_AUTOCMD12_ERR_NOTEXE		(1 << 0)
+#define SDIO_AUTOCMD12_ERR_TIMEOUT		(1 << 1)
+#define SDIO_AUTOCMD12_ERR_CRC			(1 << 2)
+#define SDIO_AUTOCMD12_ERR_ENDBIT		(1 << 3)
+#define SDIO_AUTOCMD12_ERR_INDEX		(1 << 4)
+#define SDIO_AUTOCMD12_ERR_RESP_T_BIT		(1 << 5)
+#define SDIO_AUTOCMD12_ERR_RESP_STARTBIT	(1 << 6)
+
+#define MMC_RSP_PRESENT				(1 << 0)
+/* 136 bit response */
+#define MMC_RSP_136				(1 << 1)
+/* expect valid crc */
+#define MMC_RSP_CRC				(1 << 2)
+/* card may send busy */
+#define MMC_RSP_BUSY				(1 << 3)
+/* response contains opcode */
+#define MMC_RSP_OPCODE				(1 << 4)
+
+#define MMC_BUSMODE_OPENDRAIN			1
+#define MMC_BUSMODE_PUSHPULL			2
+
+#define MMC_BUS_WIDTH_1				0
+#define MMC_BUS_WIDTH_4				2
+#define MMC_BUS_WIDTH_8				3
+
+/* Can the host do 4 bit transfers */
+#define MMC_CAP_4_BIT_DATA			(1 << 0)
+/* Can do MMC high-speed timing */
+#define MMC_CAP_MMC_HIGHSPEED			(1 << 1)
+/* Can do SD high-speed timing */
+#define MMC_CAP_SD_HIGHSPEED			(1 << 2)
+/* Can signal pending SDIO IRQs */
+#define MMC_CAP_SDIO_IRQ			(1 << 3)
+/* Talks only SPI protocols */
+#define MMC_CAP_SPI				(1 << 4)
+/* Needs polling for card-detection */
+#define MMC_CAP_NEEDS_POLL			(1 << 5)
+/* Can the host do 8 bit transfers */
+#define MMC_CAP_8_BIT_DATA			(1 << 6)
+
+/* Nonremovable e.g. eMMC */
+#define MMC_CAP_NONREMOVABLE			(1 << 8)
+/* Waits while card is busy */
+#define MMC_CAP_WAIT_WHILE_BUSY			(1 << 9)
+/* Allow erase/trim commands */
+#define MMC_CAP_ERASE				(1 << 10)
+/* can support DDR mode at 1.8V */
+#define MMC_CAP_1_8V_DDR			(1 << 11)
+/* can support DDR mode@1.2V */
+#define MMC_CAP_1_2V_DDR			(1 << 12)
+/* Can power off after boot */
+#define MMC_CAP_POWER_OFF_CARD			(1 << 13)
+/* CMD14/CMD19 bus width ok */
+#define MMC_CAP_BUS_WIDTH_TEST			(1 << 14)
+/* Host supports UHS SDR12 mode */
+#define MMC_CAP_UHS_SDR12			(1 << 15)
+/* Host supports UHS SDR25 mode */
+#define MMC_CAP_UHS_SDR25			(1 << 16)
+/* Host supports UHS SDR50 mode */
+#define MMC_CAP_UHS_SDR50			(1 << 17)
+/* Host supports UHS SDR104 mode */
+#define MMC_CAP_UHS_SDR104			(1 << 18)
+/* Host supports UHS DDR50 mode */
+#define MMC_CAP_UHS_DDR50			(1 << 19)
+/* Host supports Driver Type A */
+#define MMC_CAP_DRIVER_TYPE_A			(1 << 23)
+/* Host supports Driver Type C */
+#define MMC_CAP_DRIVER_TYPE_C			(1 << 24)
+/* Host supports Driver Type D */
+#define MMC_CAP_DRIVER_TYPE_D			(1 << 25)
+/* CMD23 supported. */
+#define MMC_CAP_CMD23				(1 << 30)
+/* Hardware reset */
+#define MMC_CAP_HW_RESET			(1 << 31)
+
+struct mvebu_mmc_cfg {
+	u32	mvebu_mmc_base;
+	u32	mvebu_mmc_clk;
+	u8	max_bus_width;
+	struct mmc_config cfg;
+};
+
+/*
+ * Functions prototypes
+ */
+
+int mvebu_mmc_init(bd_t *bis);
+
+#endif /* __MVEBU_MMC_H__ */
-- 
1.9.1

^ permalink raw reply related	[flat|nested] 6+ messages in thread