All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-10  8:55 ` klightspeed
  0 siblings, 0 replies; 12+ messages in thread
From: klightspeed-aslSrjg9ejhWX4hkXwHRhw @ 2014-09-10  8:55 UTC (permalink / raw)
  To: Jason Cooper, Ezequiel Garcia, Brian Norris, Russell King
  Cc: Ben Peddell, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Thomas Petazzoni, Gregory Clement,
	devicetree-u79uwXL29TY76Z2rM5mHXA

The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses 
Hamming ECC (strength = 1).

This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.

Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
---
 arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index d6d572e..285524f 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -143,6 +143,10 @@
 				marvell,nand-enable-arbiter;
 				nand-on-flash-bbt;
 
+				/* Use Hardware BCH ECC */
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+
 				partition@0 {
 					label = "u-boot";
 					reg = <0x0000000 0x180000>;  /* 1.5MB */
-- 
1.8.5.5

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-10  8:55 ` klightspeed
  0 siblings, 0 replies; 12+ messages in thread
From: klightspeed @ 2014-09-10  8:55 UTC (permalink / raw)
  To: Jason Cooper, Ezequiel Garcia, Brian Norris, Russell King
  Cc: Thomas Petazzoni, devicetree, Ben Peddell, Arnaud Ebalard,
	linux-mtd, Gregory Clement, linux-arm-kernel

The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses 
Hamming ECC (strength = 1).

This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.

Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
---
 arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index d6d572e..285524f 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -143,6 +143,10 @@
 				marvell,nand-enable-arbiter;
 				nand-on-flash-bbt;
 
+				/* Use Hardware BCH ECC */
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+
 				partition@0 {
 					label = "u-boot";
 					reg = <0x0000000 0x180000>;  /* 1.5MB */
-- 
1.8.5.5

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-10  8:55 ` klightspeed
  0 siblings, 0 replies; 12+ messages in thread
From: klightspeed at killerwolves.net @ 2014-09-10  8:55 UTC (permalink / raw)
  To: linux-arm-kernel

The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
(strength = 4), while the pxa3xx NAND driver by default uses 
Hamming ECC (strength = 1).

This patch changes the ECC mode on these machines to match that
of the bootloader and of the stock firmware. That way, it is
now possible to update the kernel from userland (e.g. using
standard tools from mtd-utils package); u-boot will happily
load and boot it.

Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
---
 arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
index d6d572e..285524f 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts
@@ -143,6 +143,10 @@
 				marvell,nand-enable-arbiter;
 				nand-on-flash-bbt;
 
+				/* Use Hardware BCH ECC */
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+
 				partition at 0 {
 					label = "u-boot";
 					reg = <0x0000000 0x180000>;  /* 1.5MB */
-- 
1.8.5.5

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
  2014-09-10  8:55 ` klightspeed
  (?)
@ 2014-09-13 21:08     ` Jason Cooper
  -1 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-13 21:08 UTC (permalink / raw)
  To: klightspeed-aslSrjg9ejhWX4hkXwHRhw
  Cc: Ezequiel Garcia, Brian Norris, Russell King,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Thomas Petazzoni, Gregory Clement,
	devicetree-u79uwXL29TY76Z2rM5mHXA

On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org wrote:
> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> (strength = 4), while the pxa3xx NAND driver by default uses 
> Hamming ECC (strength = 1).
> 
> This patch changes the ECC mode on these machines to match that
> of the bootloader and of the stock firmware. That way, it is
> now possible to update the kernel from userland (e.g. using
> standard tools from mtd-utils package); u-boot will happily
> load and boot it.
> 
> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
> Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
> ---
>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>  1 file changed, 4 insertions(+)

I've already applied this the mvebu/fixes:

  500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC

thx,

Jason.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-13 21:08     ` Jason Cooper
  0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-13 21:08 UTC (permalink / raw)
  To: klightspeed
  Cc: Thomas Petazzoni, devicetree, Russell King, Arnaud Ebalard,
	linux-mtd, Ezequiel Garcia, Gregory Clement, Brian Norris,
	linux-arm-kernel

On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed@killerwolves.net wrote:
> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> (strength = 4), while the pxa3xx NAND driver by default uses 
> Hamming ECC (strength = 1).
> 
> This patch changes the ECC mode on these machines to match that
> of the bootloader and of the stock firmware. That way, it is
> now possible to update the kernel from userland (e.g. using
> standard tools from mtd-utils package); u-boot will happily
> load and boot it.
> 
> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> ---
>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>  1 file changed, 4 insertions(+)

I've already applied this the mvebu/fixes:

  500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC

thx,

Jason.

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-13 21:08     ` Jason Cooper
  0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-13 21:08 UTC (permalink / raw)
  To: linux-arm-kernel

On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed at killerwolves.net wrote:
> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> (strength = 4), while the pxa3xx NAND driver by default uses 
> Hamming ECC (strength = 1).
> 
> This patch changes the ECC mode on these machines to match that
> of the bootloader and of the stock firmware. That way, it is
> now possible to update the kernel from userland (e.g. using
> standard tools from mtd-utils package); u-boot will happily
> load and boot it.
> 
> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> ---
>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>  1 file changed, 4 insertions(+)

I've already applied this the mvebu/fixes:

  500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC

thx,

Jason.

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
  2014-09-13 21:08     ` Jason Cooper
  (?)
@ 2014-09-14  2:54         ` Ben Peddell
  -1 siblings, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-09-14  2:54 UTC (permalink / raw)
  To: Jason Cooper
  Cc: Ezequiel Garcia, Brian Norris, Russell King,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Thomas Petazzoni, Gregory Clement,
	devicetree-u79uwXL29TY76Z2rM5mHXA

On 14/09/14 07:08, Jason Cooper wrote:
> On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org wrote:
>> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
>> (strength = 4), while the pxa3xx NAND driver by default uses 
>> Hamming ECC (strength = 1).
>>
>> This patch changes the ECC mode on these machines to match that
>> of the bootloader and of the stock firmware. That way, it is
>> now possible to update the kernel from userland (e.g. using
>> standard tools from mtd-utils package); u-boot will happily
>> load and boot it.
>>
>> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
>> Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
>> Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
>> Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
>> ---
>>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>>  1 file changed, 4 insertions(+)
> 
> I've already applied this the mvebu/fixes:
> 
>   500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC

That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts

The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14  2:54         ` Ben Peddell
  0 siblings, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-09-14  2:54 UTC (permalink / raw)
  To: Jason Cooper
  Cc: Thomas Petazzoni, devicetree, Russell King, Arnaud Ebalard,
	linux-mtd, Ezequiel Garcia, Gregory Clement, Brian Norris,
	linux-arm-kernel

On 14/09/14 07:08, Jason Cooper wrote:
> On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed@killerwolves.net wrote:
>> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
>> (strength = 4), while the pxa3xx NAND driver by default uses 
>> Hamming ECC (strength = 1).
>>
>> This patch changes the ECC mode on these machines to match that
>> of the bootloader and of the stock firmware. That way, it is
>> now possible to update the kernel from userland (e.g. using
>> standard tools from mtd-utils package); u-boot will happily
>> load and boot it.
>>
>> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
>> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
>> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
>> Tested-by: Arnaud Ebalard <arno@natisbad.org>
>> ---
>>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>>  1 file changed, 4 insertions(+)
> 
> I've already applied this the mvebu/fixes:
> 
>   500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC

That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts

The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14  2:54         ` Ben Peddell
  0 siblings, 0 replies; 12+ messages in thread
From: Ben Peddell @ 2014-09-14  2:54 UTC (permalink / raw)
  To: linux-arm-kernel

On 14/09/14 07:08, Jason Cooper wrote:
> On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed at killerwolves.net wrote:
>> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
>> (strength = 4), while the pxa3xx NAND driver by default uses 
>> Hamming ECC (strength = 1).
>>
>> This patch changes the ECC mode on these machines to match that
>> of the bootloader and of the stock firmware. That way, it is
>> now possible to update the kernel from userland (e.g. using
>> standard tools from mtd-utils package); u-boot will happily
>> load and boot it.
>>
>> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
>> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
>> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
>> Tested-by: Arnaud Ebalard <arno@natisbad.org>
>> ---
>>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
>>  1 file changed, 4 insertions(+)
> 
> I've already applied this the mvebu/fixes:
> 
>   500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC

That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts

The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
  2014-09-14  2:54         ` Ben Peddell
  (?)
@ 2014-09-14  4:18             ` Jason Cooper
  -1 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-14  4:18 UTC (permalink / raw)
  To: Ben Peddell
  Cc: Ezequiel Garcia, Brian Norris, Russell King,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Arnaud Ebalard, linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
	Thomas Petazzoni, Gregory Clement,
	devicetree-u79uwXL29TY76Z2rM5mHXA

On Sun, Sep 14, 2014 at 12:54:01PM +1000, Ben Peddell wrote:
> On 14/09/14 07:08, Jason Cooper wrote:
> > On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org wrote:
> >> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> >> (strength = 4), while the pxa3xx NAND driver by default uses 
> >> Hamming ECC (strength = 1).
> >>
> >> This patch changes the ECC mode on these machines to match that
> >> of the bootloader and of the stock firmware. That way, it is
> >> now possible to update the kernel from userland (e.g. using
> >> standard tools from mtd-utils package); u-boot will happily
> >> load and boot it.
> >>
> >> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> >> Signed-off-by: Ben Peddell <klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
> >> Acked-by: Ezequiel Garcia <ezequiel.garcia-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> >> Tested-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>
> >> ---
> >>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> >>  1 file changed, 4 insertions(+)
> > 
> > I've already applied this the mvebu/fixes:
> > 
> >   500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
> 
> That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
> 
> The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts

Gah!  You're right.  Applied to mvebu/fixes and Cc'd the stable v3.14+

thx,

Jason.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14  4:18             ` Jason Cooper
  0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-14  4:18 UTC (permalink / raw)
  To: Ben Peddell
  Cc: Thomas Petazzoni, devicetree, Russell King, Arnaud Ebalard,
	linux-mtd, Ezequiel Garcia, Gregory Clement, Brian Norris,
	linux-arm-kernel

On Sun, Sep 14, 2014 at 12:54:01PM +1000, Ben Peddell wrote:
> On 14/09/14 07:08, Jason Cooper wrote:
> > On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed@killerwolves.net wrote:
> >> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> >> (strength = 4), while the pxa3xx NAND driver by default uses 
> >> Hamming ECC (strength = 1).
> >>
> >> This patch changes the ECC mode on these machines to match that
> >> of the bootloader and of the stock firmware. That way, it is
> >> now possible to update the kernel from userland (e.g. using
> >> standard tools from mtd-utils package); u-boot will happily
> >> load and boot it.
> >>
> >> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> >> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> >> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> >> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> >> ---
> >>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> >>  1 file changed, 4 insertions(+)
> > 
> > I've already applied this the mvebu/fixes:
> > 
> >   500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
> 
> That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
> 
> The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts

Gah!  You're right.  Applied to mvebu/fixes and Cc'd the stable v3.14+

thx,

Jason.

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC
@ 2014-09-14  4:18             ` Jason Cooper
  0 siblings, 0 replies; 12+ messages in thread
From: Jason Cooper @ 2014-09-14  4:18 UTC (permalink / raw)
  To: linux-arm-kernel

On Sun, Sep 14, 2014 at 12:54:01PM +1000, Ben Peddell wrote:
> On 14/09/14 07:08, Jason Cooper wrote:
> > On Wed, Sep 10, 2014 at 06:55:41PM +1000, klightspeed at killerwolves.net wrote:
> >> The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC
> >> (strength = 4), while the pxa3xx NAND driver by default uses 
> >> Hamming ECC (strength = 1).
> >>
> >> This patch changes the ECC mode on these machines to match that
> >> of the bootloader and of the stock firmware. That way, it is
> >> now possible to update the kernel from userland (e.g. using
> >> standard tools from mtd-utils package); u-boot will happily
> >> load and boot it.
> >>
> >> Fixes: 92beaccd8b49 ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file")
> >> Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
> >> Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
> >> Tested-by: Arnaud Ebalard <arno@natisbad.org>
> >> ---
> >>  arch/arm/boot/dts/armada-370-netgear-rn102.dts | 4 ++++
> >>  1 file changed, 4 insertions(+)
> > 
> > I've already applied this the mvebu/fixes:
> > 
> >   500abb6ccb9e ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
> 
> That patch only affects arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
> 
> The patch I posted affects arch/arm/boot/dts/armada-370-netgear-rn102.dts

Gah!  You're right.  Applied to mvebu/fixes and Cc'd the stable v3.14+

thx,

Jason.

^ permalink raw reply	[flat|nested] 12+ messages in thread

end of thread, other threads:[~2014-09-14  4:18 UTC | newest]

Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-09-10  8:55 [PATCH reword] ARM: MVEBU: Netgear RN102: Use Hardware BCH ECC klightspeed-aslSrjg9ejhWX4hkXwHRhw
2014-09-10  8:55 ` klightspeed at killerwolves.net
2014-09-10  8:55 ` klightspeed
     [not found] ` <1410339341-3372-1-git-send-email-klightspeed-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-09-13 21:08   ` Jason Cooper
2014-09-13 21:08     ` Jason Cooper
2014-09-13 21:08     ` Jason Cooper
     [not found]     ` <20140913210829.GI30828-u4khhh1J0LxI1Ri9qeTfzeTW4wlIGRCZ@public.gmane.org>
2014-09-14  2:54       ` Ben Peddell
2014-09-14  2:54         ` Ben Peddell
2014-09-14  2:54         ` Ben Peddell
     [not found]         ` <54150349.7050503-aslSrjg9ejhWX4hkXwHRhw@public.gmane.org>
2014-09-14  4:18           ` Jason Cooper
2014-09-14  4:18             ` Jason Cooper
2014-09-14  4:18             ` Jason Cooper

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.