All of lore.kernel.org
 help / color / mirror / Atom feed
* [U-Boot] [PATCH] dw_mmc: cleanups
@ 2014-09-05 10:49 Pavel Machek
  2014-09-05 11:40 ` Marek Vasut
  2014-09-11  2:06 ` Jaehoon Chung
  0 siblings, 2 replies; 7+ messages in thread
From: Pavel Machek @ 2014-09-05 10:49 UTC (permalink / raw)
  To: u-boot


dw_mmc driver was responding to errors with debug(). Change that to
prinf so that any errors are immediately obvious. Also adjust english
in comments.

Signed-off-by: Pavel Machek <pavel@denx.de>

diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
index 0df30bc..4c16e7f 100644
--- a/drivers/mmc/dw_mmc.c
+++ b/drivers/mmc/dw_mmc.c
@@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 		}
 	}
 
-	if (i == retry)
+	if (i == retry) {
+		printf("dwmci_send_cmd: timeout..\n");
 		return TIMEOUT;
+	}
 
 	if (mask & DWMCI_INTMSK_RTO) {
-		debug("Response Timeout..\n");
+		printf("dwmci_send_cmd: Response Timeout..\n");
 		return TIMEOUT;
 	} else if (mask & DWMCI_INTMSK_RE) {
-		debug("Response Error..\n");
+		printf("dwmci_send_cmd: Response Error..\n");
 		return -1;
 	}
 
@@ -204,7 +206,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 		do {
 			mask = dwmci_readl(host, DWMCI_RINTSTS);
 			if (mask & (DWMCI_DATA_ERR | DWMCI_DATA_TOUT)) {
-				debug("DATA ERROR!\n");
+				printf("dwmci_send_cmd: DATA ERROR!\n");
 				return -1;
 			}
 		} while (!(mask & DWMCI_INTMSK_DTO));
@@ -232,16 +234,16 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
 	if ((freq == host->clock) || (freq == 0))
 		return 0;
 	/*
-	 * If host->get_mmc_clk didn't define,
+	 * If host->get_mmc_clk isn't defined,
 	 * then assume that host->bus_hz is source clock value.
-	 * host->bus_hz should be set from user.
+	 * host->bus_hz should be set by user.
 	 */
 	if (host->get_mmc_clk)
 		sclk = host->get_mmc_clk(host);
 	else if (host->bus_hz)
 		sclk = host->bus_hz;
 	else {
-		printf("Didn't get source clock value..\n");
+		printf("dwmci_setup_bus: Didn't get source clock value..\n");
 		return -EINVAL;
 	}
 
@@ -260,7 +262,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
 	do {
 		status = dwmci_readl(host, DWMCI_CMD);
 		if (timeout-- < 0) {
-			printf("TIMEOUT error!!\n");
+			printf("dwmci_setup_bus: timeout!\n");
 			return -ETIMEDOUT;
 		}
 	} while (status & DWMCI_CMD_START);
@@ -275,7 +277,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
 	do {
 		status = dwmci_readl(host, DWMCI_CMD);
 		if (timeout-- < 0) {
-			printf("TIMEOUT error!!\n");
+			printf("dwmci_setup_bus: timeout!\n");
 			return -ETIMEDOUT;
 		}
 	} while (status & DWMCI_CMD_START);
@@ -290,7 +292,7 @@ static void dwmci_set_ios(struct mmc *mmc)
 	struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
 	u32 ctype, regs;
 
-	debug("Buswidth = %d, clock: %d\n",mmc->bus_width, mmc->clock);
+	debug("Buswidth = %d, clock: %d\n", mmc->bus_width, mmc->clock);
 
 	dwmci_setup_bus(host, mmc->clock);
 	switch (mmc->bus_width) {
@@ -329,7 +331,7 @@ static int dwmci_init(struct mmc *mmc)
 	dwmci_writel(host, DWMCI_PWREN, 1);
 
 	if (!dwmci_wait_reset(host, DWMCI_RESET_ALL)) {
-		debug("%s[%d] Fail-reset!!\n",__func__,__LINE__);
+		printf("%s[%d] Fail-reset!!\n", __func__, __LINE__);
 		return -1;
 	}
 
-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

^ permalink raw reply related	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH] dw_mmc: cleanups
  2014-09-05 10:49 [U-Boot] [PATCH] dw_mmc: cleanups Pavel Machek
@ 2014-09-05 11:40 ` Marek Vasut
  2014-09-05 11:59   ` Pavel Machek
  2014-09-11  2:06 ` Jaehoon Chung
  1 sibling, 1 reply; 7+ messages in thread
From: Marek Vasut @ 2014-09-05 11:40 UTC (permalink / raw)
  To: u-boot

On Friday, September 05, 2014 at 12:49:48 PM, Pavel Machek wrote:
> dw_mmc driver was responding to errors with debug(). Change that to
> prinf so that any errors are immediately obvious. Also adjust english
> in comments.
> 
> Signed-off-by: Pavel Machek <pavel@denx.de>
> 
> diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> index 0df30bc..4c16e7f 100644
> --- a/drivers/mmc/dw_mmc.c
> +++ b/drivers/mmc/dw_mmc.c
> @@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> mmc_cmd *cmd, }
>  	}
> 
> -	if (i == retry)
> +	if (i == retry) {
> +		printf("dwmci_send_cmd: timeout..\n");

puts(), please fix globally.
[...]

Best regards,
Marek Vasut

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH] dw_mmc: cleanups
  2014-09-05 11:40 ` Marek Vasut
@ 2014-09-05 11:59   ` Pavel Machek
  2014-09-05 12:05     ` Marek Vasut
  0 siblings, 1 reply; 7+ messages in thread
From: Pavel Machek @ 2014-09-05 11:59 UTC (permalink / raw)
  To: u-boot

On Fri 2014-09-05 13:40:58, Marek Vasut wrote:
> On Friday, September 05, 2014 at 12:49:48 PM, Pavel Machek wrote:
> > dw_mmc driver was responding to errors with debug(). Change that to
> > prinf so that any errors are immediately obvious. Also adjust english
> > in comments.
> > 
> > Signed-off-by: Pavel Machek <pavel@denx.de>
> > 
> > diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> > index 0df30bc..4c16e7f 100644
> > --- a/drivers/mmc/dw_mmc.c
> > +++ b/drivers/mmc/dw_mmc.c
> > @@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> > mmc_cmd *cmd, }
> >  	}
> > 
> > -	if (i == retry)
> > +	if (i == retry) {
> > +		printf("dwmci_send_cmd: timeout..\n");
> 
> puts(), please fix globally.

Won't.

printf() is canonical way of printing, and is used in such way at 1000
places in u-boot.

But feel free to prepare patchv2 yourself if you think it is worth the
effort.

									Pavel

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH] dw_mmc: cleanups
  2014-09-05 11:59   ` Pavel Machek
@ 2014-09-05 12:05     ` Marek Vasut
  2014-09-05 12:25       ` Pavel Machek
  0 siblings, 1 reply; 7+ messages in thread
From: Marek Vasut @ 2014-09-05 12:05 UTC (permalink / raw)
  To: u-boot

On Friday, September 05, 2014 at 01:59:19 PM, Pavel Machek wrote:
> On Fri 2014-09-05 13:40:58, Marek Vasut wrote:
> > On Friday, September 05, 2014 at 12:49:48 PM, Pavel Machek wrote:
> > > dw_mmc driver was responding to errors with debug(). Change that to
> > > prinf so that any errors are immediately obvious. Also adjust english
> > > in comments.
> > > 
> > > Signed-off-by: Pavel Machek <pavel@denx.de>
> > > 
> > > diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> > > index 0df30bc..4c16e7f 100644
> > > --- a/drivers/mmc/dw_mmc.c
> > > +++ b/drivers/mmc/dw_mmc.c
> > > @@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> > > mmc_cmd *cmd, }
> > > 
> > >  	}
> > > 
> > > -	if (i == retry)
> > > +	if (i == retry) {
> > > +		printf("dwmci_send_cmd: timeout..\n");
> > 
> > puts(), please fix globally.
> 
> Won't.
> 
> printf() is canonical way of printing, and is used in such way at 1000
> places in u-boot.

The agreement is to use puts() when there are no args attached to the print,
so that the code size is reduced.

Best regards,
Marek Vasut

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH] dw_mmc: cleanups
  2014-09-05 12:05     ` Marek Vasut
@ 2014-09-05 12:25       ` Pavel Machek
  0 siblings, 0 replies; 7+ messages in thread
From: Pavel Machek @ 2014-09-05 12:25 UTC (permalink / raw)
  To: u-boot

On Fri 2014-09-05 14:05:48, Marek Vasut wrote:
> On Friday, September 05, 2014 at 01:59:19 PM, Pavel Machek wrote:
> > On Fri 2014-09-05 13:40:58, Marek Vasut wrote:
> > > On Friday, September 05, 2014 at 12:49:48 PM, Pavel Machek wrote:
> > > > dw_mmc driver was responding to errors with debug(). Change that to
> > > > prinf so that any errors are immediately obvious. Also adjust english
> > > > in comments.
> > > > 
> > > > Signed-off-by: Pavel Machek <pavel@denx.de>
> > > > 
> > > > diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> > > > index 0df30bc..4c16e7f 100644
> > > > --- a/drivers/mmc/dw_mmc.c
> > > > +++ b/drivers/mmc/dw_mmc.c
> > > > @@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct
> > > > mmc_cmd *cmd, }
> > > > 
> > > >  	}
> > > > 
> > > > -	if (i == retry)
> > > > +	if (i == retry) {
> > > > +		printf("dwmci_send_cmd: timeout..\n");
> > > 
> > > puts(), please fix globally.
> > 
> > Won't.
> > 
> > printf() is canonical way of printing, and is used in such way at 1000
> > places in u-boot.
> 
> The agreement is to use puts() when there are no args attached to the print,
> so that the code size is reduced.

I did not make such agreement with you, and don't think obfuscating
code with printf->puts conversion is a good idea. If there's
codingstyle document I missed somewhere, please point me to it.

If you think global conversion is a good idea, please do it, so that
old code does not serve as a bad example. But I don't think it saves
any size, compared to speed of serial line it does not save any time,
either.
									Pavel
PS: Sorry for flames on the mailing list, but marex explicitely asked
me to take discussion there.

-- 
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH] dw_mmc: cleanups
  2014-09-05 10:49 [U-Boot] [PATCH] dw_mmc: cleanups Pavel Machek
  2014-09-05 11:40 ` Marek Vasut
@ 2014-09-11  2:06 ` Jaehoon Chung
  2014-09-12  7:21   ` Chin Liang See
  1 sibling, 1 reply; 7+ messages in thread
From: Jaehoon Chung @ 2014-09-11  2:06 UTC (permalink / raw)
  To: u-boot

Hi, Pavel.

It looks good to me. 
If you're ok, can i suggest one thing?

On 09/05/2014 07:49 PM, Pavel Machek wrote:
> 
> dw_mmc driver was responding to errors with debug(). Change that to
> prinf so that any errors are immediately obvious. Also adjust english
> in comments.
> 
> Signed-off-by: Pavel Machek <pavel@denx.de>
> 
> diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> index 0df30bc..4c16e7f 100644
> --- a/drivers/mmc/dw_mmc.c
> +++ b/drivers/mmc/dw_mmc.c
> @@ -177,14 +177,16 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
>  		}
>  	}
>  
> -	if (i == retry)
> +	if (i == retry) {
> +		printf("dwmci_send_cmd: timeout..\n");
>  		return TIMEOUT;
> +	}
>  
>  	if (mask & DWMCI_INTMSK_RTO) {
> -		debug("Response Timeout..\n");
> +		printf("dwmci_send_cmd: Response Timeout..\n");
>  		return TIMEOUT;
>  	} else if (mask & DWMCI_INTMSK_RE) {
> -		debug("Response Error..\n");
> +		printf("dwmci_send_cmd: Response Error..\n");
>  		return -1;
>  	}
>  
> @@ -204,7 +206,7 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
>  		do {
>  			mask = dwmci_readl(host, DWMCI_RINTSTS);
>  			if (mask & (DWMCI_DATA_ERR | DWMCI_DATA_TOUT)) {
> -				debug("DATA ERROR!\n");
> +				printf("dwmci_send_cmd: DATA ERROR!\n");
>  				return -1;
>  			}
>  		} while (!(mask & DWMCI_INTMSK_DTO));
> @@ -232,16 +234,16 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
>  	if ((freq == host->clock) || (freq == 0))
>  		return 0;
>  	/*
> -	 * If host->get_mmc_clk didn't define,
> +	 * If host->get_mmc_clk isn't defined,
>  	 * then assume that host->bus_hz is source clock value.
> -	 * host->bus_hz should be set from user.
> +	 * host->bus_hz should be set by user.
>  	 */
>  	if (host->get_mmc_clk)
>  		sclk = host->get_mmc_clk(host);
>  	else if (host->bus_hz)
>  		sclk = host->bus_hz;
>  	else {
> -		printf("Didn't get source clock value..\n");
> +		printf("dwmci_setup_bus: Didn't get source clock value..\n");
>  		return -EINVAL;
>  	}
>  
> @@ -260,7 +262,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
>  	do {
>  		status = dwmci_readl(host, DWMCI_CMD);
>  		if (timeout-- < 0) {
> -			printf("TIMEOUT error!!\n");
> +			printf("dwmci_setup_bus: timeout!\n");
>  			return -ETIMEDOUT;
>  		}
>  	} while (status & DWMCI_CMD_START);
> @@ -275,7 +277,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
>  	do {
>  		status = dwmci_readl(host, DWMCI_CMD);
>  		if (timeout-- < 0) {
> -			printf("TIMEOUT error!!\n");
> +			printf("dwmci_setup_bus: timeout!\n");
According to your the main purpose, this patch is goal that noticed where/what error is occurred.
Then i think good that add the "__LINE__".
Because there are same message like "dwmci_setup_bus: tiemout!\n" at some place.

Then i think we don't need to discuss about this patch with Marek. :)

Best Regards,
Jaehoon Chung

>  			return -ETIMEDOUT;
>  		}
>  	} while (status & DWMCI_CMD_START);
> @@ -290,7 +292,7 @@ static void dwmci_set_ios(struct mmc *mmc)
>  	struct dwmci_host *host = (struct dwmci_host *)mmc->priv;
>  	u32 ctype, regs;
>  
> -	debug("Buswidth = %d, clock: %d\n",mmc->bus_width, mmc->clock);
> +	debug("Buswidth = %d, clock: %d\n", mmc->bus_width, mmc->clock);
>  
>  	dwmci_setup_bus(host, mmc->clock);
>  	switch (mmc->bus_width) {
> @@ -329,7 +331,7 @@ static int dwmci_init(struct mmc *mmc)
>  	dwmci_writel(host, DWMCI_PWREN, 1);
>  
>  	if (!dwmci_wait_reset(host, DWMCI_RESET_ALL)) {
> -		debug("%s[%d] Fail-reset!!\n",__func__,__LINE__);
> +		printf("%s[%d] Fail-reset!!\n", __func__, __LINE__);
>  		return -1;
>  	}
>  
> 

^ permalink raw reply	[flat|nested] 7+ messages in thread

* [U-Boot] [PATCH] dw_mmc: cleanups
  2014-09-11  2:06 ` Jaehoon Chung
@ 2014-09-12  7:21   ` Chin Liang See
  0 siblings, 0 replies; 7+ messages in thread
From: Chin Liang See @ 2014-09-12  7:21 UTC (permalink / raw)
  To: u-boot

Hi,

On Thu, 2014-09-11 at 11:06 +0900, Jaehoon Chung wrote:
> Hi, Pavel.
> 
> It looks good to me. 
> If you're ok, can i suggest one thing?
> 
> On 09/05/2014 07:49 PM, Pavel Machek wrote:
> > 
> > dw_mmc driver was responding to errors with debug(). Change that to
> > prinf so that any errors are immediately obvious. Also adjust english
> > in comments.
> > 
> > Signed-off-by: Pavel Machek <pavel@denx.de>
> > 
> > diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c
> > index 0df30bc..4c16e7f 100644
> > --- a/drivers/mmc/dw_mmc.c
> > +++ b/drivers/mmc/dw_mmc.c
> > @@ -260,7 +262,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
> >  	do {
> >  		status = dwmci_readl(host, DWMCI_CMD);
> >  		if (timeout-- < 0) {
> > -			printf("TIMEOUT error!!\n");
> > +			printf("dwmci_setup_bus: timeout!\n");
> >  			return -ETIMEDOUT;
> >  		}
> >  	} while (status & DWMCI_CMD_START);
> > @@ -275,7 +277,7 @@ static int dwmci_setup_bus(struct dwmci_host *host, u32 freq)
> >  	do {
> >  		status = dwmci_readl(host, DWMCI_CMD);
> >  		if (timeout-- < 0) {
> > -			printf("TIMEOUT error!!\n");
> > +			printf("dwmci_setup_bus: timeout!\n");
> According to your the main purpose, this patch is goal that noticed where/what error is occurred.
> Then i think good that add the "__LINE__".
> Because there are same message like "dwmci_setup_bus: tiemout!\n" at some place.
> 
> Then i think we don't need to discuss about this patch with Marek. :)
> 

This patch looks good except need to distinguish the error location as
pointed by Jaehoon.

Thanks
Chin Liang


> Best Regards,
> Jaehoon Chung
> 

^ permalink raw reply	[flat|nested] 7+ messages in thread

end of thread, other threads:[~2014-09-12  7:21 UTC | newest]

Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2014-09-05 10:49 [U-Boot] [PATCH] dw_mmc: cleanups Pavel Machek
2014-09-05 11:40 ` Marek Vasut
2014-09-05 11:59   ` Pavel Machek
2014-09-05 12:05     ` Marek Vasut
2014-09-05 12:25       ` Pavel Machek
2014-09-11  2:06 ` Jaehoon Chung
2014-09-12  7:21   ` Chin Liang See

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.