From mboxrd@z Thu Jan 1 00:00:00 1970 From: Masahiro Yamada Date: Mon, 15 Dec 2014 23:26:21 +0900 Subject: [U-Boot] [PATCH 16/26] mpc8260: remove ep8260 board support In-Reply-To: <1418653608-14177-1-git-send-email-yamada.m@jp.panasonic.com> References: <1418653608-14177-1-git-send-email-yamada.m@jp.panasonic.com> Message-ID: <1418653608-14177-17-git-send-email-yamada.m@jp.panasonic.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de This board is still a non-generic board. Signed-off-by: Masahiro Yamada Cc: Frank Panno --- arch/powerpc/cpu/mpc8260/Kconfig | 4 - board/ep8260/Kconfig | 9 - board/ep8260/MAINTAINERS | 6 - board/ep8260/Makefile | 8 - board/ep8260/ep8260.c | 304 ---------------- board/ep8260/ep8260.h | 24 -- board/ep8260/flash.c | 395 --------------------- board/ep8260/mii_phy.c | 107 ------ configs/ep8260_defconfig | 3 - doc/README.scrapyard | 1 + include/configs/ep8260.h | 744 --------------------------------------- 11 files changed, 1 insertion(+), 1604 deletions(-) delete mode 100644 board/ep8260/Kconfig delete mode 100644 board/ep8260/MAINTAINERS delete mode 100644 board/ep8260/Makefile delete mode 100644 board/ep8260/ep8260.c delete mode 100644 board/ep8260/ep8260.h delete mode 100644 board/ep8260/flash.c delete mode 100644 board/ep8260/mii_phy.c delete mode 100644 configs/ep8260_defconfig delete mode 100644 include/configs/ep8260.h diff --git a/arch/powerpc/cpu/mpc8260/Kconfig b/arch/powerpc/cpu/mpc8260/Kconfig index d4132a0..1032712 100644 --- a/arch/powerpc/cpu/mpc8260/Kconfig +++ b/arch/powerpc/cpu/mpc8260/Kconfig @@ -16,9 +16,6 @@ config TARGET_CPU86 config TARGET_CPU87 bool "Support CPU87" -config TARGET_EP8260 - bool "Support ep8260" - config TARGET_EP82XXM bool "Support ep82xxm" @@ -51,7 +48,6 @@ endchoice source "board/atc/Kconfig" source "board/cpu86/Kconfig" source "board/cpu87/Kconfig" -source "board/ep8260/Kconfig" source "board/ep82xxm/Kconfig" source "board/freescale/mpc8266ads/Kconfig" source "board/funkwerk/vovpn-gw/Kconfig" diff --git a/board/ep8260/Kconfig b/board/ep8260/Kconfig deleted file mode 100644 index 5d876f4..0000000 --- a/board/ep8260/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_EP8260 - -config SYS_BOARD - default "ep8260" - -config SYS_CONFIG_NAME - default "ep8260" - -endif diff --git a/board/ep8260/MAINTAINERS b/board/ep8260/MAINTAINERS deleted file mode 100644 index bfa923c..0000000 --- a/board/ep8260/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -EP8260 BOARD -#M: Frank Panno -S: Orphan (since 2014-06) -F: board/ep8260/ -F: include/configs/ep8260.h -F: configs/ep8260_defconfig diff --git a/board/ep8260/Makefile b/board/ep8260/Makefile deleted file mode 100644 index dd08b74..0000000 --- a/board/ep8260/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2002-2006 -# Wolfgang Denk, DENX Software Engineering, wd at denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = ep8260.o flash.o mii_phy.o diff --git a/board/ep8260/ep8260.c b/board/ep8260/ep8260.c deleted file mode 100644 index 3697d24..0000000 --- a/board/ep8260/ep8260.c +++ /dev/null @@ -1,304 +0,0 @@ -/* - * (C) Copyright 2001, 2002 - * Wolfgang Denk, DENX Software Engineering, wd at denx.de. - * - * (C) Copyright 2002 - * Frank Panno , Delphin Technology AG - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include "ep8260.h" -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA30 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA29 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA28 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA27 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA26 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA25 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA24 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA23 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA22 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA21 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA20 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA19 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA18 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA17 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA16 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA15 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA14 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA13 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA12 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA11 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA10 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PA9 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PA8 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ - /* PA6 */ { 0, 0, 0, 1, 0, 0 }, /* PA6 */ - /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ - /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ - /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ - /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ - /* PA1 */ { 0, 0, 0, 1, 0, 0 }, /* PA1 */ - /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ - }, - - /* Port B configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PB30 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB29 */ { 0, 1, 1, 1, 0, 0 }, /* */ - /* PB28 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB27 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB26 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB25 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PB24 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PB23 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PB22 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PB21 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB20 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB19 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB18 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_DV */ - /* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_ER */ - /* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TX_ER */ - /* PB14 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TX_EN */ - /* PB13 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII COL */ - /* PB12 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII CRS */ - /* PB11 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[3] */ - /* PB10 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[2] */ - /* PB9 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[1] */ - /* PB8 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[0] */ - /* PB7 */ { 0, 0, 0, 0, 0, 0 }, /* PB7 */ - /* PB6 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[1] */ - /* PB5 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[2] */ - /* PB4 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[3] */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ - /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ - /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* */ - /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ - /* PC27 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[0] */ - /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ - /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ - /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ - /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PC19 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PC18 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII CLK15 */ - /* PC16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII CLK16 */ - /* PC15 */ { 0, 0, 0, 1, 0, 0 }, /* PC15 */ - /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */ - /* PC12 */ { 0, 0, 0, 1, 0, 0 }, /* PC12 */ - /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* PC11 */ - /* PC10 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PC9 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ - /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ - /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ - /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ - /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ - /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ - /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* */ - /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* */ - /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PD30 */ { 0, 1, 1, 1, 0, 0 }, /* */ - /* PD29 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PD28 */ { 0, 0, 0, 1, 0, 0 }, /* PD28 */ - /* PD27 */ { 0, 0, 0, 1, 0, 0 }, /* PD27 */ - /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */ - /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ - /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ - /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ - /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ - /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ - /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ - /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* */ - /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* */ - /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ - /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ - /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ - /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -/* ------------------------------------------------------------------------- */ - -/* - * Setup CS4 to enable the Board Control/Status registers. - * Otherwise the smcs won't work. -*/ -int board_early_init_f (void) -{ - volatile t_ep_regs *regs = (t_ep_regs *) CONFIG_SYS_REGS_BASE; - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - - memctl->memc_br4 = CONFIG_SYS_BR4_PRELIM; - memctl->memc_or4 = CONFIG_SYS_OR4_PRELIM; - regs->bcsr1 = 0x62; /* to enable terminal on SMC1 */ - regs->bcsr2 = 0x30; /* enable NVRAM and writing FLASH */ - return 0; -} - -void reset_phy (void) -{ - volatile t_ep_regs *regs = (t_ep_regs *) CONFIG_SYS_REGS_BASE; - - regs->bcsr4 = 0xC0; -} - -/* - * Check Board Identity: - * I don' know, how the next board revisions will be coded. - * Thats why its a static interpretation ... -*/ - -int checkboard (void) -{ - volatile t_ep_regs *regs = (t_ep_regs *) CONFIG_SYS_REGS_BASE; - uint major = 0, minor = 0; - - switch (regs->bcsr0) { - case 0x02: - major = 1; - break; - case 0x03: - major = 1; - minor = 1; - break; - case 0x06: - major = 1; - minor = 3; - break; - default: - break; - } - printf ("Board: Embedded Planet EP8260, Revision %d.%d\n", - major, minor); - return 0; -} - - -/* ------------------------------------------------------------------------- */ - - -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - volatile uchar c = 0; - volatile uchar *ramaddr = (uchar *) (CONFIG_SYS_SDRAM_BASE) + 0x110; - -/* - ulong psdmr = CONFIG_SYS_PSDMR; -#ifdef CONFIG_SYS_LSDRAM - ulong lsdmr = CONFIG_SYS_LSDMR; -#endif -*/ - long size = CONFIG_SYS_SDRAM0_SIZE; - int i; - - -/* -* Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): -* -* "At system reset, initialization software must set up the -* programmable parameters in the memory controller banks registers -* (ORx, BRx, P/LSDMR). After all memory parameters are configured, -* system software should execute the following initialization sequence -* for each SDRAM device. -* -* 1. Issue a PRECHARGE-ALL-BANKS command -* 2. Issue eight CBR REFRESH commands -* 3. Issue a MODE-SET command to initialize the mode register -* -* The initial commands are executed by setting P/LSDMR[OP] and -* accessing the SDRAM with a single-byte transaction." -* -* The appropriate BRx/ORx registers have already been set when we -* get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. -*/ - - memctl->memc_psrt = CONFIG_SYS_PSRT; - memctl->memc_mptpr = CONFIG_SYS_MPTPR; - - memctl->memc_psdmr = (ulong) CONFIG_SYS_PSDMR | PSDMR_OP_PREA; - *ramaddr = c; - - memctl->memc_psdmr = (ulong) CONFIG_SYS_PSDMR | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) - *ramaddr = c; - - memctl->memc_psdmr = (ulong) CONFIG_SYS_PSDMR | PSDMR_OP_MRW; - *ramaddr = c; - - memctl->memc_psdmr = (ulong) CONFIG_SYS_PSDMR | PSDMR_OP_NORM | PSDMR_RFEN; - *ramaddr = c; - -#ifndef CONFIG_SYS_RAMBOOT -#ifdef CONFIG_SYS_LSDRAM - size += CONFIG_SYS_SDRAM1_SIZE; - ramaddr = (uchar *) (CONFIG_SYS_SDRAM1_BASE) + 0x8c; - memctl->memc_lsrt = CONFIG_SYS_LSRT; - - memctl->memc_lsdmr = (ulong) CONFIG_SYS_LSDMR | PSDMR_OP_PREA; - *ramaddr = c; - - memctl->memc_lsdmr = (ulong) CONFIG_SYS_LSDMR | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) - *ramaddr = c; - - memctl->memc_lsdmr = (ulong) CONFIG_SYS_LSDMR | PSDMR_OP_MRW; - *ramaddr = c; - - memctl->memc_lsdmr = (ulong) CONFIG_SYS_LSDMR | PSDMR_OP_NORM | PSDMR_RFEN; - *ramaddr = c; -#endif /* CONFIG_SYS_LSDRAM */ -#endif /* CONFIG_SYS_RAMBOOT */ - return (size * 1024 * 1024); -} diff --git a/board/ep8260/ep8260.h b/board/ep8260/ep8260.h deleted file mode 100644 index 3032b14..0000000 --- a/board/ep8260/ep8260.h +++ /dev/null @@ -1,24 +0,0 @@ -#ifndef __EP8260_H__ -#define __EP8260_H__ - -typedef struct tt_ep_regs { - volatile unsigned char bcsr0; - volatile unsigned char bcsr1; - volatile unsigned char bcsr2; - volatile unsigned char bcsr3; - volatile unsigned char bcsr4; - volatile unsigned char bcsr5; - volatile unsigned char bcsr6; - volatile unsigned char bcsr7; - volatile unsigned char bcsr8; - volatile unsigned char bcsr9; - volatile unsigned char bcsr10; - volatile unsigned char bcsr11; - volatile unsigned char bcsr12; - volatile unsigned char bcsr13; - volatile unsigned char bcsr14; - volatile unsigned char bcsr15; -} t_ep_regs; -typedef t_ep_regs *tp_ep_regs; - -#endif diff --git a/board/ep8260/flash.c b/board/ep8260/flash.c deleted file mode 100644 index 44f63ee..0000000 --- a/board/ep8260/flash.c +++ /dev/null @@ -1,395 +0,0 @@ -/* - * (C) Copyright 2001, 2002 - * Wolfgang Denk, DENX Software Engineering, wd at denx.de. - * - * (C) Copyright 2002 - * Frank Panno , Delphin Technology AG - * - * Flash Routines for AMD device AM29DL323DB on the EP8260 board. - * - * This file is based on board/tqm8260/flash.c. - *-------------------------------------------------------------------- - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -#define V_ULONG(a) (*(volatile unsigned long *)( a )) -#define V_BYTE(a) (*(volatile unsigned char *)( a )) - - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - - -/*----------------------------------------------------------------------- - */ -void flash_reset(void) -{ - if( flash_info[0].flash_id != FLASH_UNKNOWN ) { - V_ULONG( flash_info[0].start[0] ) = 0x00F000F0; - V_ULONG( flash_info[0].start[0] + 4 ) = 0x00F000F0; - } -} - -/*----------------------------------------------------------------------- - */ -ulong flash_get_size( ulong baseaddr, flash_info_t *info ) -{ - short i; - unsigned long flashtest_h, flashtest_l; - - /* Write auto select command sequence and test FLASH answer */ - V_ULONG(baseaddr + ((ulong)0x0555 << 3)) = 0x00AA00AA; - V_ULONG(baseaddr + ((ulong)0x02AA << 3)) = 0x00550055; - V_ULONG(baseaddr + ((ulong)0x0555 << 3)) = 0x00900090; - V_ULONG(baseaddr + 4 + ((ulong)0x0555 << 3)) = 0x00AA00AA; - V_ULONG(baseaddr + 4 + ((ulong)0x02AA << 3)) = 0x00550055; - V_ULONG(baseaddr + 4 + ((ulong)0x0555 << 3)) = 0x00900090; - - flashtest_h = V_ULONG(baseaddr); /* manufacturer ID */ - flashtest_l = V_ULONG(baseaddr + 4); - - if ((int)flashtest_h == AMD_MANUFACT) { - info->flash_id = FLASH_MAN_AMD; - } else { - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - return (0); /* no or unknown flash */ - } - - flashtest_h = V_ULONG(baseaddr + 8); /* device ID */ - flashtest_l = V_ULONG(baseaddr + 12); - if (flashtest_h != flashtest_l) { - info->flash_id = FLASH_UNKNOWN; - return(0); - } - - switch((int)flashtest_h) { - case AMD_ID_DL323B: - info->flash_id += FLASH_AMDL323B; - info->sector_count = 71; - info->size = 0x01000000; /* 4 * 4 MB = 16 MB */ - break; - case AMD_ID_LV640U: /* AMDLV640 and AMDLV641 have same ID */ - info->flash_id += FLASH_AMLV640U; - info->sector_count = 128; - info->size = 0x02000000; /* 4 * 8 MB = 32 MB */ - break; - default: - info->flash_id = FLASH_UNKNOWN; - return(0); /* no or unknown flash */ - } - - if(flashtest_h == AMD_ID_LV640U) { - /* set up sector start adress table (uniform sector type) */ - for (i = 0; i < info->sector_count; i++) - info->start[i] = baseaddr + (i * 0x00040000); - } else { - /* set up sector start adress table (bottom sector type) */ - for (i = 0; i < 8; i++) { - info->start[i] = baseaddr + (i * 0x00008000); - } - for (i = 8; i < info->sector_count; i++) { - info->start[i] = baseaddr + (i * 0x00040000) - 0x001C0000; - } - } - /* check for protected sectors */ - for (i = 0; i < info->sector_count; i++) { - /* read sector protection at sector address, (A7 .. A0) = 0x02 */ - if ((V_ULONG( info->start[i] + 16 ) & 0x00010001) || - (V_ULONG( info->start[i] + 20 ) & 0x00010001)) { - info->protect[i] = 1; /* D0 = 1 if protected */ - } else { - info->protect[i] = 0; - } - } - - flash_reset(); - return(info->size); -} - -/*----------------------------------------------------------------------- - */ -unsigned long flash_init (void) -{ - unsigned long size_b0 = 0; - int i; - - /* Init: no FLASHes known */ - for (i=0; i>20); - } - - /* - * protect monitor and environment sectors - */ - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH0_BASE - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1, - &flash_info[0]); -#endif - -#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) -# ifndef CONFIG_ENV_SIZE -# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -# endif - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, - &flash_info[0]); -#endif - - return (size_b0); -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch ((info->flash_id >> 16) & 0xff) { - case FLASH_MAN_AMD: printf ("AMD "); break; - default: printf ("Unknown Vendor "); break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_AMDL323B: printf ("29DL323B (32 M, bottom sector)\n"); - break; - case FLASH_AMLV640U: printf ("29LV640U (64 M, uniform sector)\n"); - break; - default: printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i=0; isector_count; ++i) { - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s", - info->start[i], - info->protect[i] ? " (RO)" : " " - ); - } - printf ("\n"); - return; -} - -/*----------------------------------------------------------------------- - */ -int flash_erase (flash_info_t *info, int s_first, int s_last) -{ - int flag, prot, sect, l_sect; - ulong start, now, last; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect]) - prot++; - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - l_sect = -1; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - V_ULONG( info->start[0] + (0x0555 << 3) ) = 0x00AA00AA; - V_ULONG( info->start[0] + (0x02AA << 3) ) = 0x00550055; - V_ULONG( info->start[0] + (0x0555 << 3) ) = 0x00800080; - V_ULONG( info->start[0] + (0x0555 << 3) ) = 0x00AA00AA; - V_ULONG( info->start[0] + (0x02AA << 3) ) = 0x00550055; - V_ULONG( info->start[0] + 4 + (0x0555 << 3) ) = 0x00AA00AA; - V_ULONG( info->start[0] + 4 + (0x02AA << 3) ) = 0x00550055; - V_ULONG( info->start[0] + 4 + (0x0555 << 3) ) = 0x00800080; - V_ULONG( info->start[0] + 4 + (0x0555 << 3) ) = 0x00AA00AA; - V_ULONG( info->start[0] + 4 + (0x02AA << 3) ) = 0x00550055; - udelay (1000); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - V_ULONG( info->start[sect] ) = 0x00300030; - V_ULONG( info->start[sect] + 4 ) = 0x00300030; - l_sect = sect; - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* wait at least 80us - let's wait 1 ms */ - udelay (1000); - - /* - * We wait for the last triggered sector - */ - if (l_sect < 0) - goto DONE; - - start = get_timer (0); - last = start; - while ((V_ULONG( info->start[l_sect] ) & 0x00800080) != 0x00800080 || - (V_ULONG( info->start[l_sect] + 4 ) & 0x00800080) != 0x00800080) - { - if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - return 1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - serial_putc ('.'); - last = now; - } - } - - DONE: - /* reset to read mode */ - flash_reset (); - - printf (" done\n"); - return 0; -} - -static int write_dword (flash_info_t *, ulong, unsigned char *); - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - ulong dp; - static unsigned char bb[8]; - int i, l, rc, cc = cnt; - - dp = (addr & ~7); /* get lower dword aligned address */ - - /* - * handle unaligned start bytes - */ - if ((l = addr - dp) != 0) { - for (i = 0; i < 8; i++) - bb[i] = (i < l || (i-l) >= cc) ? V_BYTE(dp+i) : *src++; - if ((rc = write_dword(info, dp, bb)) != 0) - { - return (rc); - } - dp += 8; - cc -= 8 - l; - } - - /* - * handle word aligned part - */ - while (cc >= 8) { - if ((rc = write_dword(info, dp, src)) != 0) { - return (rc); - } - dp += 8; - src += 8; - cc -= 8; - } - - if (cc <= 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - for (i = 0; i < 8; i++) { - bb[i] = (i < cc) ? *src++ : V_BYTE(dp+i); - } - return (write_dword(info, dp, bb)); -} - -/*----------------------------------------------------------------------- - * Write a dword to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_dword (flash_info_t *info, ulong dest, unsigned char * pdata) -{ - ulong start; - ulong cl = 0, ch =0; - int flag, i; - - for (ch=0, i=0; i < 4; i++) - ch = (ch << 8) + *pdata++; /* high word */ - for (cl=0, i=0; i < 4; i++) - cl = (cl << 8) + *pdata++; /* low word */ - - /* Check if Flash is (sufficiently) erased */ - if ((*((vu_long *)dest) & ch) != ch - ||(*((vu_long *)(dest + 4)) & cl) != cl) - { - return (2); - } - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - V_ULONG( info->start[0] + (0x0555 << 3) ) = 0x00AA00AA; - V_ULONG( info->start[0] + (0x02AA << 3) ) = 0x00550055; - V_ULONG( info->start[0] + (0x0555 << 3) ) = 0x00A000A0; - V_ULONG( dest ) = ch; - V_ULONG( info->start[0] + 4 + (0x0555 << 3) ) = 0x00AA00AA; - V_ULONG( info->start[0] + 4 + (0x02AA << 3) ) = 0x00550055; - V_ULONG( info->start[0] + 4 + (0x0555 << 3) ) = 0x00A000A0; - V_ULONG( dest + 4 ) = cl; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* data polling for D7 */ - start = get_timer (0); - while (((V_ULONG( dest ) & 0x00800080) != (ch & 0x00800080)) || - ((V_ULONG( dest + 4 ) & 0x00800080) != (cl & 0x00800080))) { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - return (1); - } - } - return (0); -} diff --git a/board/ep8260/mii_phy.c b/board/ep8260/mii_phy.c deleted file mode 100644 index c7aa275..0000000 --- a/board/ep8260/mii_phy.c +++ /dev/null @@ -1,107 +0,0 @@ -#include -#include -#include "ep8260.h" - -#define MII_MDIO 0x01 -#define MII_MDCK 0x02 -#define MII_MDIR 0x04 - -void -mii_discover_phy(void) -{ - int known; - unsigned short phy_reg; - unsigned long phy_id; - - known = 0; - printf("Discovering phy @ 0: "); - phy_id = mii_phy_read(2) << 16; - phy_id |= mii_phy_read(3); - if ((phy_id & 0xFFFFFC00) == 0x00137800) { - printf("Level One "); - if ((phy_id & 0x000003F0) == 0xE0) { - printf("LXT971A Revision %d\n", (int)(phy_id & 0xF)); - known = 1; - } - else printf("unknown type\n"); - } - else printf("unknown OUI = 0x%08lX\n", phy_id); - - phy_reg = mii_phy_read(1); - if (!(phy_reg & 0x0004)) printf("Link is down\n"); - if (!(phy_reg & 0x0020)) printf("Auto-negotiation not complete\n"); - if (phy_reg & 0x0002) printf("Jabber condition detected\n"); - if (phy_reg & 0x0010) printf("Remote fault condition detected \n"); - - if (known) { - phy_reg = mii_phy_read(17); - if (phy_reg & 0x0400) - printf("Phy operating@%d MBit/s in %s-duplex mode\n", - phy_reg & 0x4000 ? 100 : 10, - phy_reg & 0x0200 ? "full" : "half"); - else - printf("bad link!!\n"); -/* -left off: no link, green 100MBit, yellow 10MBit -right off: no activity, green full-duplex, yellow half-duplex -*/ - mii_phy_write(20, 0x0452); - } -} - -unsigned short -mii_phy_read(unsigned short reg) -{ - int i; - unsigned short tmp, val = 0, adr = 0; - t_ep_regs *regs = (t_ep_regs*)CONFIG_SYS_REGS_BASE; - - tmp = 0x6002 | (adr << 7) | (reg << 2); - regs->bcsr4 = 0xC3; - for (i = 0; i < 64; i++) { - regs->bcsr4 ^= MII_MDCK; - } - for (i = 0; i < 16; i++) { - regs->bcsr4 &= ~MII_MDCK; - if (tmp & 0x8000) regs->bcsr4 |= MII_MDIO; - else regs->bcsr4 &= ~MII_MDIO; - regs->bcsr4 |= MII_MDCK; - tmp <<= 1; - } - regs->bcsr4 |= MII_MDIR; - for (i = 0; i < 16; i++) { - val <<= 1; - regs->bcsr4 = MII_MDIO | (regs->bcsr4 | MII_MDCK); - if (regs->bcsr4 & MII_MDIO) val |= 1; - regs->bcsr4 = MII_MDIO | (regs->bcsr4 &= ~MII_MDCK); - } - return val; -} - -void -mii_phy_write(unsigned short reg, unsigned short val) -{ - int i; - unsigned short tmp, adr = 0; - t_ep_regs *regs = (t_ep_regs*)CONFIG_SYS_REGS_BASE; - - tmp = 0x5002 | (adr << 7) | (reg << 2); - regs->bcsr4 = 0xC3; - for (i = 0; i < 64; i++) { - regs->bcsr4 ^= MII_MDCK; - } - for (i = 0; i < 16; i++) { - regs->bcsr4 &= ~MII_MDCK; - if (tmp & 0x8000) regs->bcsr4 |= MII_MDIO; - else regs->bcsr4 &= ~MII_MDIO; - regs->bcsr4 |= MII_MDCK; - tmp <<= 1; - } - for (i = 0; i < 16; i++) { - regs->bcsr4 &= ~MII_MDCK; - if (val & 0x8000) regs->bcsr4 |= MII_MDIO; - else regs->bcsr4 &= ~MII_MDIO; - regs->bcsr4 |= MII_MDCK; - val <<= 1; - } -} diff --git a/configs/ep8260_defconfig b/configs/ep8260_defconfig deleted file mode 100644 index 1cce900..0000000 --- a/configs/ep8260_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_MPC8260=y -CONFIG_TARGET_EP8260=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index 0845651..46b6dbe 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +ep8260 powerpc mpc8260 - - Frank Panno ppmc8260 powerpc mpc8260 - - Brad Kemp sacsng powerpc mpc8260 - - Jerry Van Baren cogent_mpc8260 powerpc mpc8260 - - Murray Jensen diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h deleted file mode 100644 index 9cd3054..0000000 --- a/include/configs/ep8260.h +++ /dev/null @@ -1,744 +0,0 @@ -/* - * (C) Copyright 2002 - * Frank Panno , Delphin Technology AG - * - * This file is based on similar values for other boards found in other - * U-Boot config files, and some that I found in the EP8260 manual. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - * - * "EP8260 H, V.1.1" - * - 64M 60x Bus SDRAM - * - 32M Local Bus SDRAM - * - 16M Flash (4 x AM29DL323DB90WDI) - * - 128k NVRAM with RTC - * - * "EP8260 H2, V.1.3" (CONFIG_SYS_EP8260_H2) - * - 300MHz/133MHz/66MHz - * - 64M 60x Bus SDRAM - * - 32M Local Bus SDRAM - * - 32M Flash - * - 128k NVRAM with RTC - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* Define this to enable support the EP8260 H2 version */ -#define CONFIG_SYS_EP8260_H2 1 -/* #undef CONFIG_SYS_EP8260_H2 */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -/* What is the oscillator's (UX2) frequency in Hz? */ -#define CONFIG_8260_CLKIN (66 * 1000 * 1000) - -/*----------------------------------------------------------------------- - * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual - *----------------------------------------------------------------------- - * What should MODCK_H be? It is dependent on the oscillator - * frequency, MODCK[1-3], and desired CPM and core frequencies. - * Here are some example values (all frequencies are in MHz): - * - * MODCK_H MODCK[1-3] Osc CPM Core - * ------- ---------- --- --- ---- - * 0x2 0x2 33 133 133 - * 0x2 0x3 33 133 166 - * 0x2 0x4 33 133 200 - * 0x2 0x5 33 133 233 - * 0x2 0x6 33 133 266 - * - * 0x5 0x5 66 133 133 - * 0x5 0x6 66 133 166 - * 0x5 0x7 66 133 200 * - * 0x6 0x0 66 133 233 - * 0x6 0x1 66 133 266 - * 0x6 0x2 66 133 300 - */ -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110) -#else -#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110) -#endif - -/* Define this if you want to boot from 0x00000100. If you don't define - * this, you will need to program the bootloader to 0xfff00000, and - * get the hardware reset config words at 0xfe000000. The simplest - * way to do that is to program the bootloader at both addresses. - * It is suggested that you just let U-Boot live at 0x00000000. - */ -/* #define CONFIG_SYS_SBC_BOOT_LOW 1 */ /* only for HRCW */ -/* #undef CONFIG_SYS_SBC_BOOT_LOW */ - -/* The reset command will not work as expected if the reset address does - * not point to the correct address. - */ - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 - -/* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/ep8260/config.mk - * The main FLASH is whichever is connected to *CS0. U-Boot expects - * this to be the SIMM. - */ -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_FLASH0_BASE 0xFE000000 -#define CONFIG_SYS_FLASH0_SIZE 32 -#else -#define CONFIG_SYS_FLASH0_BASE 0xFF000000 -#define CONFIG_SYS_FLASH0_SIZE 16 -#endif - -/* What should the base address of the secondary FLASH be and how big - * is it (in Mbytes)? The secondary FLASH is whichever is connected - * to *CS6. U-Boot expects this to be the on board FLASH. If you don't - * want it enabled, don't define these constants. - */ -#define CONFIG_SYS_FLASH1_BASE 0 -#define CONFIG_SYS_FLASH1_SIZE 0 -#undef CONFIG_SYS_FLASH1_BASE -#undef CONFIG_SYS_FLASH1_SIZE - -/* What should be the base address of SDRAM DIMM (60x bus) and how big is - * it (in Mbytes)? -*/ -#define CONFIG_SYS_SDRAM0_BASE 0x00000000 -#define CONFIG_SYS_SDRAM0_SIZE 64 - -/* define CONFIG_SYS_LSDRAM if you want to enable the 32M SDRAM on the - * local bus (8260 local bus is NOT cacheable!) -*/ -/* #define CONFIG_SYS_LSDRAM */ -#undef CONFIG_SYS_LSDRAM - -#ifdef CONFIG_SYS_LSDRAM -/* What should be the base address of SDRAM DIMM (local bus) and how big is - * it (in Mbytes)? -*/ - #define CONFIG_SYS_SDRAM1_BASE 0x04000000 - #define CONFIG_SYS_SDRAM1_SIZE 32 -#else - #define CONFIG_SYS_SDRAM1_BASE 0 - #define CONFIG_SYS_SDRAM1_SIZE 0 - #undef CONFIG_SYS_SDRAM1_BASE - #undef CONFIG_SYS_SDRAM1_SIZE -#endif /* CONFIG_SYS_LSDRAM */ - -/* What should be the base address of NVRAM and how big is - * it (in Bytes) - */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000 -#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16 - -/* The RTC is a Dallas DS1556 - */ -#define CONFIG_RTC_DS1556 - -/* What should be the base address of the LEDs and switch S0? - * If you don't want them enabled, don't define this. - */ -#define CONFIG_SYS_LED_BASE 0x00000000 -#undef CONFIG_SYS_LED_BASE - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere. - */ -#define CONFIG_CONS_ON_SMC /* define if console on SMC */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on neither */ -#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ -#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ -#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */ - -#if ( CONFIG_ETHER_INDEX == 3 ) - -/* - * - Rx-CLK is CLK15 - * - Tx-CLK is CLK16 - * - RAM for BD/Buffers is on the local Bus (see 28-13) - * - Enable Half Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) - -/* - * - RAM for BD/Buffers is on the local Bus (see 28-13) - */ -#ifdef CONFIG_SYS_LSDRAM - #define CONFIG_SYS_CPMFCR_RAMTYPE 3 -#else /* CONFIG_SYS_LSDRAM */ - #define CONFIG_SYS_CPMFCR_RAMTYPE 0 -#endif /* CONFIG_SYS_LSDRAM */ - -/* - Enable Half Duplex in FSMR */ -/* # define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ -# define CONFIG_SYS_FCC_PSMR 0 - -#else /* CONFIG_ETHER_INDEX */ -# error "on EP8260 ethernet must be FCC3" -#endif /* CONFIG_ETHER_INDEX */ - -/* - * select i2c support configuration - * - * Supported configurations are {none, software, hardware} drivers. - * If the software driver is chosen, there are some additional - * configuration items that the driver uses to drive the port pins. - */ -#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ - -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* This is for HARD, must go */ - -/* - * Software (bit-bang) I2C driver configuration - */ -#ifdef CONFIG_SYS_I2C_SOFT -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT_SPEED 50000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SYS_I2C_SOFT */ - -/* #define CONFIG_RTC_DS174x */ - -/* Define this to reserve an entire FLASH sector (256 KB) for - * environment variables. Otherwise, the environment will be - * put in the same sector as U-Boot, and changing variables - * will erase U-Boot temporarily - */ -#define CONFIG_ENV_IN_OWN_SECT - -/* Define to allow the user to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* What should the console's baud rate be? */ -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_BAUDRATE 9600 -#else -#define CONFIG_BAUDRATE 115200 -#endif - -/* Ethernet MAC address */ -#define CONFIG_ETHADDR 00:10:EC:00:30:8C - -#define CONFIG_IPADDR 192.168.254.130 -#define CONFIG_SERVERIP 192.168.254.49 - -/* Set to a positive value to delay for running BOOTCOMMAND */ -#define CONFIG_BOOTDELAY -1 - -/* undef this to save memory */ -#define CONFIG_SYS_LONGHELP - -/* Monitor Command Prompt */ - -/* Define this variable to enable the "hush" shell (from - Busybox) as command line interpreter, thus enabling - powerful command line syntax like - if...then...else...fi conditionals or `&&' and '||' - constructs ("shell scripts"). - If undefined, you get the old, much simpler behaviour - with a somewhat smapper memory footprint. -*/ -#define CONFIG_SYS_HUSH_PARSER - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_CDP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_PING -#define CONFIG_CMD_PORTIO -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SAVES -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_SNTP - -#undef CONFIG_CMD_XIMG - -/* Where do the internal registers live? */ -#define CONFIG_SYS_IMMR 0xF0000000 -#define CONFIG_SYS_DEFAULT_IMMR 0x00010000 - -/* Where do the on board registers (CS4) live? */ -#define CONFIG_SYS_REGS_BASE 0xFA000000 - -/***************************************************************************** - * - * You should not have to modify any of the following settings - * - *****************************************************************************/ - -#define CONFIG_EP8260 11 /* on an Embedded Planet EP8260 Board, Rev. 11 */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ - -/* - * Miscellaneous configurable options - */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) - -#define CONFIG_SYS_MAXARGS 8 /* max number of command args */ - -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#ifdef CONFIG_SYS_LSDRAM - #define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */ - #define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ -#else - #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ - #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */ -#endif /* CONFIG_SYS_LSDRAM */ - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - */ - -#if defined(CONFIG_SYS_SBC_BOOT_LOW) -# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) -#else -# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0x00000000) -#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */ - -#ifdef CONFIG_SYS_EP8260_H2 -/* get the HRCW ISB field from CONFIG_SYS_DEFAULT_IMMR */ -#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_DEFAULT_IMMR & 0x10000000) >> 10) |\ - ((CONFIG_SYS_DEFAULT_IMMR & 0x01000000) >> 7) |\ - ((CONFIG_SYS_DEFAULT_IMMR & 0x00100000) >> 4) ) - -#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM |\ - HRCW_L2CPC01 |\ - CONFIG_SYS_SBC_HRCW_IMMR |\ - HRCW_APPC10 |\ - HRCW_CS10PC01 |\ - CONFIG_SYS_SBC_MODCK_H |\ - CONFIG_SYS_SBC_HRCW_BOOT_FLAGS) -#else -#define CONFIG_SYS_HRCW_MASTER 0x10400245 -#endif - -/* no slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent. - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#else -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ -#endif - -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#else -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ -#endif - -#ifndef CONFIG_SYS_RAMBOOT -# define CONFIG_ENV_IS_IN_FLASH 1 - -# ifdef CONFIG_ENV_IN_OWN_SECT -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) -# define CONFIG_ENV_SECT_SIZE 0x40000 -# else -# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE) -# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ -# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ -# endif /* CONFIG_ENV_IN_OWN_SECT */ -#else -# define CONFIG_ENV_IS_IN_NVRAM 1 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -# define CONFIG_ENV_SIZE 0x200 -#endif /* CONFIG_SYS_RAMBOOT */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE |\ - HID0_DCE |\ - HID0_ICFI |\ - HID0_DCI |\ - HID0_IFEM |\ - HID0_ABE) -#ifdef CONFIG_SYS_LSDRAM -/* 8260 local bus is NOT cacheable */ -#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\ - HID0_IFEM |\ - HID0_ABE |\ - HID0_EMCP) -#else /* !CONFIG_SYS_LSDRAM */ -#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\ - HID0_IFEM |\ - HID0_ABE |\ - HID0_EMCP) -#endif /* CONFIG_SYS_LSDRAM */ - -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMR 0 - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BCR (BCR_EBM |\ - BCR_PLDP |\ - BCR_EAV |\ - BCR_NPQM0) - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\ - SIUMCR_APPC10 |\ - SIUMCR_CS10PC01) - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#ifdef CONFIG_SYS_EP8260_H2 -/* TBD: Find out why setting the BMT to 0xff causes the FCC to - * generate TX buffer underrun errors for large packets under - * Linux - */ -#define CONFIG_SYS_SYPCR_BMT 0x00000600 -#else -#define CONFIG_SYS_SYPCR_BMT SYPCR_BMT -#endif - -#ifdef CONFIG_SYS_LSDRAM -#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ - CONFIG_SYS_SYPCR_BMT |\ - SYPCR_PBME |\ - SYPCR_LBME |\ - SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ - CONFIG_SYS_SYPCR_BMT |\ - SYPCR_PBME |\ - SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\ - TMCNTSC_ALR |\ - TMCNTSC_TCF |\ - TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_PISCR (PISCR_PS |\ - PISCR_PTF |\ - PISCR_PTE) -#else -#define CONFIG_SYS_PISCR 0 -#endif - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - */ -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_SCCR (SCCR_DFBRG00) -#else -#define CONFIG_SYS_SCCR (SCCR_DFBRG01) -#endif - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/*----------------------------------------------------------------------- - * MPTPR - Memory Refresh Timer Prescale Register 10-32 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_MPTPR (0x0A00 & MPTPR_PTP_MSK) - -/* - * Init Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90WDI) - * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Micron 48LC8M16A2TG) - * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Micron 48LC8M16A2TG) - * 3 unused - * 4 60x GPCM 8 bit Board Regs, NVRTC - * 5 unused - * 6 unused - * 7 unused - * 8 PCMCIA - * 9 unused - * 10 unused - * 11 unused -*/ - -/*----------------------------------------------------------------------- - * BRx - Base Register - * Ref: Section 10.3.1 on page 10-14 - * ORx - Option Register - * Ref: Section 10.3.2 on page 10-18 - *----------------------------------------------------------------------- - */ - -/* Bank 0 - FLASH - * - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_DECC_NONE |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_8_CLK |\ - ORxG_EHTR) - -/* Bank 1 - SDRAM - * PSDRAM - */ -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI1_A6 |\ - ORxS_NUMR_12) - -#ifdef CONFIG_SYS_EP8260_H2 -#define CONFIG_SYS_PSDMR 0xC34E246E -#else -#define CONFIG_SYS_PSDMR 0xC34E2462 -#endif - -#define CONFIG_SYS_PSRT 0x64 - -#ifdef CONFIG_SYS_LSDRAM -/* Bank 2 - SDRAM - * LSDRAM - */ - - #define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\ - BRx_PS_32 |\ - BRx_MS_SDRAM_L |\ - BRx_V) - - #define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI0_A9 |\ - ORxS_NUMR_12) - - #define CONFIG_SYS_LSDMR 0x416A2562 - #define CONFIG_SYS_LSRT 0x64 -#else - #define CONFIG_SYS_LSRT 0x0 -#endif /* CONFIG_SYS_LSDRAM */ - -/* Bank 4 - On board registers - * NVRTC and BCSR - */ -#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\ - BRx_PS_8 |\ - BRx_MS_GPCM_P |\ - BRx_V) -/* -#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_10_CLK |\ - ORxG_TRLX) -*/ -#define CONFIG_SYS_OR4_PRELIM 0xfff00854 - -#ifdef _NOT_USED_SINCE_NOT_WORKING_ -/* Bank 8 - On board registers - * PCMCIA (currently not working!) - */ -#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\ - BRx_PS_16 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR8_PRELIM (ORxG_AM_MSK |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SETA |\ - ORxG_SCY_10_CLK) -#endif - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "" -#define MTDPARTS_DEFAULT "" -*/ - -#endif /* __CONFIG_H */ -- 1.9.1