From mboxrd@z Thu Jan 1 00:00:00 1970 From: Stefan Roese Date: Tue, 14 Apr 2015 12:46:55 +0200 Subject: [U-Boot] [PATCH v2 13/13] arm: mvebu: Add Armada A38x DB-88F6820-GP board support In-Reply-To: <1429008415-27458-1-git-send-email-sr@denx.de> References: <1429008415-27458-1-git-send-email-sr@denx.de> Message-ID: <1429008415-27458-14-git-send-email-sr@denx.de> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de This patch adds support for the Marvell DB-88F6820-GP Armada A38x evaluation board. Supported peripherals are: - UART - Ethernet (mvneta) - I2C - SPI (including SPI NOR flash) Please note that this board support right now only supports the main U-Boot. Without the bin_hdr integration (DDR training etc). This will be added in a few days / weeks to complete this board port. But till then this U-Boot version can be run on the target via the original Marvell U-Boot via this command: tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000 Signed-off-by: Stefan Roese --- Changes in v2: - Update to 256KiB env sector as required for M25P128 - Add I2C IO expander initialization (fan etc) - Enable PL310 L2 cache as this is needed for correct caching OPs arch/arm/Kconfig | 6 ++ board/Marvell/db-88f6820-gp/Kconfig | 15 ++++ board/Marvell/db-88f6820-gp/Makefile | 7 ++ board/Marvell/db-88f6820-gp/binary.0 | 16 +++++ board/Marvell/db-88f6820-gp/db-88f6820-gp.c | 103 ++++++++++++++++++++++++++++ board/Marvell/db-88f6820-gp/kwbimage.cfg | 12 ++++ configs/db-88f6820-gp_defconfig | 2 + include/configs/db-88f6820-gp.h | 72 +++++++++++++++++++ 8 files changed, 233 insertions(+) create mode 100644 board/Marvell/db-88f6820-gp/Kconfig create mode 100644 board/Marvell/db-88f6820-gp/Makefile create mode 100644 board/Marvell/db-88f6820-gp/binary.0 create mode 100644 board/Marvell/db-88f6820-gp/db-88f6820-gp.c create mode 100644 board/Marvell/db-88f6820-gp/kwbimage.cfg create mode 100644 configs/db-88f6820-gp_defconfig create mode 100644 include/configs/db-88f6820-gp.h diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 7ed0e20..96b3f0c 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -118,6 +118,11 @@ config KIRKWOOD bool "Marvell Kirkwood" select CPU_ARM926EJS +config TARGET_DB_88F6820_GP + bool "Support DB-88F6820-GP" + select CPU_V7 + select SUPPORT_SPL + config TARGET_DB_MV784MP_GP bool "Support db-mv784mp-gp" select CPU_V7 @@ -780,6 +785,7 @@ source "board/BuR/kwb/Kconfig" source "board/BuR/tseries/Kconfig" source "board/CarMediaLab/flea3/Kconfig" source "board/Marvell/aspenite/Kconfig" +source "board/Marvell/db-88f6820-gp/Kconfig" source "board/Marvell/db-mv784mp-gp/Kconfig" source "board/Marvell/gplugd/Kconfig" source "board/altera/socfpga/Kconfig" diff --git a/board/Marvell/db-88f6820-gp/Kconfig b/board/Marvell/db-88f6820-gp/Kconfig new file mode 100644 index 0000000..b2e9115 --- /dev/null +++ b/board/Marvell/db-88f6820-gp/Kconfig @@ -0,0 +1,15 @@ +if TARGET_DB_88F6820_GP + +config SYS_BOARD + default "db-88f6820-gp" + +config SYS_VENDOR + default "Marvell" + +config SYS_SOC + default "mvebu" + +config SYS_CONFIG_NAME + default "db-88f6820-gp" + +endif diff --git a/board/Marvell/db-88f6820-gp/Makefile b/board/Marvell/db-88f6820-gp/Makefile new file mode 100644 index 0000000..58d40dd --- /dev/null +++ b/board/Marvell/db-88f6820-gp/Makefile @@ -0,0 +1,7 @@ +# +# Copyright (C) 2015 Stefan Roese +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := db-88f6820-gp.o diff --git a/board/Marvell/db-88f6820-gp/binary.0 b/board/Marvell/db-88f6820-gp/binary.0 new file mode 100644 index 0000000..57a4cbf --- /dev/null +++ b/board/Marvell/db-88f6820-gp/binary.0 @@ -0,0 +1,16 @@ +-------- +WARNING: +-------- +This file should contain the bin_hdr generated by the original Marvell +U-Boot implementation. As this is currently not included in this +U-Boot version, we have added this placeholder, so that the U-Boot +image can be generated without errors. + +If you have a known to be working bin_hdr for your board, then you +just need to replace this text file here with the binary header +and recompile U-Boot. + +In a few weeks, mainline U-Boot will get support to generate the +bin_hdr with the DDR training code itself. By implementing this code +as SPL U-Boot. Then this file will not be needed any more and will +get removed. diff --git a/board/Marvell/db-88f6820-gp/db-88f6820-gp.c b/board/Marvell/db-88f6820-gp/db-88f6820-gp.c new file mode 100644 index 0000000..51ac495 --- /dev/null +++ b/board/Marvell/db-88f6820-gp/db-88f6820-gp.c @@ -0,0 +1,103 @@ +/* + * Copyright (C) 2015 Stefan Roese + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#define BIT(nr) (1UL << (nr)) + +#define ETH_PHY_CTRL_REG 0 +#define ETH_PHY_CTRL_POWER_DOWN_BIT 11 +#define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT) + +/* + * Those values and defines are taken from the Marvell U-Boot version + * "u-boot-2013.01-2014_T3.0" + */ +#define DB_GP_88F68XX_GPP_OUT_ENA_LOW \ + (~(BIT(1) | BIT(4) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | \ + BIT(10) | BIT(11) | BIT(19) | BIT(22) | BIT(23) | BIT(25) | \ + BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31))) +#define DB_GP_88F68XX_GPP_OUT_ENA_MID \ + (~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) | \ + BIT(16) | BIT(17) | BIT(18))) + +#define DB_GP_88F68XX_GPP_OUT_VAL_LOW 0x0 +#define DB_GP_88F68XX_GPP_OUT_VAL_MID 0x0 +#define DB_GP_88F68XX_GPP_POL_LOW 0x0 +#define DB_GP_88F68XX_GPP_POL_MID 0x0 + +/* IO expander on Marvell GP board includes e.g. fan enabling */ +struct marvell_io_exp { + u8 chip; + u8 addr; + u8 val; +}; + +static struct marvell_io_exp io_exp[] = { + { 0x20, 6, 0x20 }, /* Configuration registers: Bit on --> Input bits */ + { 0x20, 7, 0xC3 }, /* Configuration registers: Bit on --> Input bits */ + { 0x20, 2, 0x1D }, /* Output Data, register#0 */ + { 0x20, 3, 0x18 }, /* Output Data, register#1 */ + { 0x21, 6, 0xC3 }, /* Configuration registers: Bit on --> Input bits */ + { 0x21, 7, 0x31 }, /* Configuration registers: Bit on --> Input bits */ + { 0x21, 2, 0x08 }, /* Output Data, register#0 */ + { 0x21, 3, 0xC0 } /* Output Data, register#1 */ +}; + +int board_early_init_f(void) +{ + /* Configure MPP */ + writel(0x11111111, MVEBU_MPP_BASE + 0x00); + writel(0x11111111, MVEBU_MPP_BASE + 0x04); + writel(0x11244011, MVEBU_MPP_BASE + 0x08); + writel(0x22222111, MVEBU_MPP_BASE + 0x0c); + writel(0x22200002, MVEBU_MPP_BASE + 0x10); + writel(0x30042022, MVEBU_MPP_BASE + 0x14); + writel(0x55550555, MVEBU_MPP_BASE + 0x18); + writel(0x00005550, MVEBU_MPP_BASE + 0x1c); + + /* Set GPP Out value */ + writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); + writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); + + /* Set GPP Polarity */ + writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); + writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); + + /* Set GPP Out Enable */ + writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); + writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); + + return 0; +} + +int board_init(void) +{ + int i; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + /* Init I2C IO expanders */ + for (i = 0; i < ARRAY_SIZE(io_exp); i++) + i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1); + + return 0; +} + +int checkboard(void) +{ + puts("Board: Marvell DB-88F6820-GP\n"); + + return 0; +} diff --git a/board/Marvell/db-88f6820-gp/kwbimage.cfg b/board/Marvell/db-88f6820-gp/kwbimage.cfg new file mode 100644 index 0000000..e812454 --- /dev/null +++ b/board/Marvell/db-88f6820-gp/kwbimage.cfg @@ -0,0 +1,12 @@ +# +# Copyright (C) 2014 Stefan Roese +# + +# Armada XP uses version 1 image format +VERSION 1 + +# Boot Media configurations +BOOT_FROM spi + +# Binary Header (bin_hdr) with DDR3 training code +BINARY board/Marvell/db-88f6820-gp/binary.0 0000005b 00000068 diff --git a/configs/db-88f6820-gp_defconfig b/configs/db-88f6820-gp_defconfig new file mode 100644 index 0000000..0d6f0de --- /dev/null +++ b/configs/db-88f6820-gp_defconfig @@ -0,0 +1,2 @@ +CONFIG_ARM=y +CONFIG_TARGET_DB_88F6820_GP=y diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h new file mode 100644 index 0000000..05a3a38 --- /dev/null +++ b/include/configs/db-88f6820-gp.h @@ -0,0 +1,72 @@ +/* + * Copyright (C) 2014 Stefan Roese + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_DB_88F6820_GP_H +#define _CONFIG_DB_88F6820_GP_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_ARMADA_XP /* SOC Family Name */ +#define CONFIG_DB_88F6820_GP /* Board target name for DDR training */ + +#define CONFIG_SYS_L2_PL310 + +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_DISPLAY_BOARDINFO_LATE + +#define CONFIG_SYS_TEXT_BASE 0x04000000 +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#include +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_CMD_TFTPPUT +#define CONFIG_CMD_TIME + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MVTWSI +#define CONFIG_I2C_MVTWSI_BASE MVEBU_TWSI_BASE +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 +#define CONFIG_SPI_FLASH_STMICRO + +/* Environment in SPI NOR flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET (1 << 20) /* 1MiB in */ +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ +#define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ + +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ +#define CONFIG_PHY_ADDR { 1, 0 } +#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ +#define CONFIG_SYS_ALT_MEMTEST + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +#endif /* _CONFIG_DB_88F6820_GP_H */ -- 2.3.5