From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1030305AbbD1N0D (ORCPT ); Tue, 28 Apr 2015 09:26:03 -0400 Received: from mga11.intel.com ([192.55.52.93]:11674 "EHLO mga11.intel.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1030261AbbD1NZU (ORCPT ); Tue, 28 Apr 2015 09:25:20 -0400 X-ExtLoop1: 1 X-IronPort-AV: E=Sophos;i="5.11,663,1422950400"; d="scan'208";a="702108458" From: Heikki Krogerus To: Felipe Balbi Cc: David Cohen , Greg Kroah-Hartman , Stephen Boyd , Baolu Lu , Paul Bolle , linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org, Kishon Vijay Abraham I Subject: [PATCHv3 11/11] phy: add driver for TI TUSB1210 ULPI PHY Date: Tue, 28 Apr 2015 16:24:46 +0300 Message-Id: <1430227486-225197-12-git-send-email-heikki.krogerus@linux.intel.com> X-Mailer: git-send-email 2.1.4 In-Reply-To: <1430227486-225197-1-git-send-email-heikki.krogerus@linux.intel.com> References: <1430227486-225197-1-git-send-email-heikki.krogerus@linux.intel.com> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org TUSB1210 ULPI PHY has vendor specific register for eye diagram tuning. On some platforms the system firmware has set optimized value to it. In order to not loose the optimized value, the driver stores it during probe and restores it every time the PHY is powered back on. Signed-off-by: Heikki Krogerus Acked-by: David Cohen Cc: Kishon Vijay Abraham I --- drivers/phy/Kconfig | 7 +++ drivers/phy/Makefile | 1 + drivers/phy/phy-tusb1210.c | 153 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 161 insertions(+) create mode 100644 drivers/phy/phy-tusb1210.c diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index a53bd5b..fceac96 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -309,4 +309,11 @@ config PHY_QCOM_UFS help Support for UFS PHY on QCOM chipsets. +config PHY_TUSB1210 + tristate "TI TUSB1210 ULPI PHY module" + depends on USB_ULPI_BUS + select GENERIC_PHY + help + Support for TI TUSB1210 USB ULPI PHY. + endmenu diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index f126251..0a20418 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -40,3 +40,4 @@ obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o +obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o diff --git a/drivers/phy/phy-tusb1210.c b/drivers/phy/phy-tusb1210.c new file mode 100644 index 0000000..07efdd3 --- /dev/null +++ b/drivers/phy/phy-tusb1210.c @@ -0,0 +1,153 @@ +/** + * tusb1210.c - TUSB1210 USB ULPI PHY driver + * + * Copyright (C) 2015 Intel Corporation + * + * Author: Heikki Krogerus + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include + +#include "ulpi_phy.h" + +#define TUSB1210_VENDOR_SPECIFIC2 0x80 +#define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT 0 +#define TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT 4 +#define TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT 6 + +struct tusb1210 { + struct ulpi *ulpi; + struct phy *phy; + struct gpio_desc *gpio_reset; + struct gpio_desc *gpio_cs; + u8 vendor_specific2; +}; + +static int tusb1210_power_on(struct phy *phy) +{ + struct tusb1210 *tusb = phy_get_drvdata(phy); + + gpiod_set_value_cansleep(tusb->gpio_reset, 1); + gpiod_set_value_cansleep(tusb->gpio_cs, 1); + + /* Restore the optional eye diagram optimization value */ + if (tusb->vendor_specific2) + ulpi_write(tusb->ulpi, TUSB1210_VENDOR_SPECIFIC2, + tusb->vendor_specific2); + + return 0; +} + +static int tusb1210_power_off(struct phy *phy) +{ + struct tusb1210 *tusb = phy_get_drvdata(phy); + + gpiod_set_value_cansleep(tusb->gpio_reset, 0); + gpiod_set_value_cansleep(tusb->gpio_cs, 0); + + return 0; +} + +static struct phy_ops phy_ops = { + .power_on = tusb1210_power_on, + .power_off = tusb1210_power_off, + .owner = THIS_MODULE, +}; + +static int tusb1210_probe(struct ulpi *ulpi) +{ + struct gpio_desc *gpio; + struct tusb1210 *tusb; + u8 val, reg; + int ret; + + tusb = devm_kzalloc(&ulpi->dev, sizeof(*tusb), GFP_KERNEL); + if (!tusb) + return -ENOMEM; + + gpio = devm_gpiod_get(&ulpi->dev, "reset"); + if (!IS_ERR(gpio)) { + ret = gpiod_direction_output(gpio, 0); + if (ret) + return ret; + gpiod_set_value_cansleep(gpio, 1); + tusb->gpio_reset = gpio; + } + + gpio = devm_gpiod_get(&ulpi->dev, "cs"); + if (!IS_ERR(gpio)) { + ret = gpiod_direction_output(gpio, 0); + if (ret) + return ret; + gpiod_set_value_cansleep(gpio, 1); + tusb->gpio_cs = gpio; + } + + /* + * VENDOR_SPECIFIC2 register in TUSB1210 can be used for configuring eye + * diagram optimization and DP/DM swap. + */ + + /* High speed output drive strength configuration */ + device_property_read_u8(&ulpi->dev, "ihstx", &val); + reg = val << TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT; + + /* High speed output impedance configuration */ + device_property_read_u8(&ulpi->dev, "zhsdrv", &val); + reg |= val << TUSB1210_VENDOR_SPECIFIC2_ZHSDRV_SHIFT; + + /* DP/DM swap control */ + device_property_read_u8(&ulpi->dev, "datapolarity", &val); + reg |= val << TUSB1210_VENDOR_SPECIFIC2_DP_SHIFT; + + if (reg) { + ulpi_write(ulpi, TUSB1210_VENDOR_SPECIFIC2, reg); + tusb->vendor_specific2 = reg; + } + + tusb->phy = ulpi_phy_create(ulpi, &phy_ops); + if (IS_ERR(tusb->phy)) + return PTR_ERR(tusb->phy); + + tusb->ulpi = ulpi; + + phy_set_drvdata(tusb->phy, tusb); + ulpi_set_drvdata(ulpi, tusb); + return 0; +} + +static void tusb1210_remove(struct ulpi *ulpi) +{ + struct tusb1210 *tusb = ulpi_get_drvdata(ulpi); + + ulpi_phy_destroy(ulpi, tusb->phy); +} + +#define TI_VENDOR_ID 0x0451 + +static const struct ulpi_device_id tusb1210_ulpi_id[] = { + { TI_VENDOR_ID, 0x1507, }, + { }, +}; +MODULE_DEVICE_TABLE(ulpi, tusb1210_ulpi_id); + +static struct ulpi_driver tusb1210_driver = { + .id_table = tusb1210_ulpi_id, + .probe = tusb1210_probe, + .remove = tusb1210_remove, + .driver = { + .name = "tusb1210", + .owner = THIS_MODULE, + }, +}; + +module_ulpi_driver(tusb1210_driver); + +MODULE_AUTHOR("Intel Corporation"); +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("TUSB1210 ULPI PHY driver"); -- 2.1.4