From: Matej Vido <vido@cesnet.cz>
To: dev@dpdk.org
Subject: [PATCH 0/2] Virtual PMD using sze2 layer for COMBO cards
Date: Fri, 19 Jun 2015 10:24:59 +0200 [thread overview]
Message-ID: <1434702301-4509-1-git-send-email-vido@cesnet.cz> (raw)
This is virtual PMD which communicates with COMBO-80G and COMBO-100G
cards through sze2 layer. Communication with COMBO card is managed
through interface provided by libsze2 library and kernel modules
(combov3, szedata2_cv3).
To compile and use PMD, it is necessary to have libsze2 library installed and
kernel modules (combov3, szedata2_cv3) loaded.
Therefore in default configuration PMD compilation is disabled. To compile
szedata2 PMD, it is necessary to enable CONFIG_RTE_LIBRTE_PMD_SZEDATA2=y.
We have done performance measurement. Results are available in pdf file:
https://www.liberouter.org/wp-content/uploads/2015/06/pmd_szedata2_dpdk_measurement.pdf
Measurement was not done with final version of firmware. Performance will
be increased soon with new firmware version.
Matej Vido (2):
szedata2: new poll mode driver
doc: added documentation for szedata2 PMD
config/common_bsdapp | 5 +
config/common_linuxapp | 5 +
doc/guides/nics/index.rst | 1 +
doc/guides/nics/szedata2.rst | 105 ++
doc/guides/prog_guide/source_org.rst | 1 +
drivers/net/Makefile | 1 +
drivers/net/szedata2/Makefile | 62 ++
drivers/net/szedata2/rte_eth_szedata2.c | 1120 +++++++++++++++++++++
drivers/net/szedata2/rte_eth_szedata2.h | 96 ++
drivers/net/szedata2/rte_pmd_szedata2_version.map | 4 +
mk/rte.app.mk | 3 +
11 files changed, 1403 insertions(+)
create mode 100644 doc/guides/nics/szedata2.rst
create mode 100644 drivers/net/szedata2/Makefile
create mode 100644 drivers/net/szedata2/rte_eth_szedata2.c
create mode 100644 drivers/net/szedata2/rte_eth_szedata2.h
create mode 100644 drivers/net/szedata2/rte_pmd_szedata2_version.map
--
Matej Vido
Software Developer
CESNET, a. l. e.
next reply other threads:[~2015-06-19 8:25 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-19 8:24 Matej Vido [this message]
2015-06-19 8:25 ` [PATCH 1/2] szedata2: new poll mode driver Matej Vido
2016-03-21 17:45 ` Stephen Hemminger
2016-03-24 17:52 ` Matej Vido
2015-06-19 8:25 ` [PATCH 2/2] doc: added documentation for szedata2 PMD Matej Vido
2015-09-18 8:32 ` [PATCH v2 0/5] Virtual PMD using sze2 layer for COMBO cards Matej Vido
2015-09-18 8:32 ` [PATCH v2 1/5] szedata2: add new poll mode driver Matej Vido
2015-10-26 15:10 ` Thomas Monjalon
2015-09-18 8:32 ` [PATCH v2 2/5] szedata2: add handling of scattered packets in RX Matej Vido
2015-09-18 8:32 ` [PATCH v2 3/5] szedata2: add handling of scattered packets in TX Matej Vido
2015-10-26 14:55 ` Thomas Monjalon
2015-10-27 17:40 ` Matej Vido
2015-09-18 8:32 ` [PATCH v2 4/5] doc: add documentation for szedata2 PMD Matej Vido
2015-10-26 15:00 ` Thomas Monjalon
2015-10-26 15:09 ` Thomas Monjalon
2015-10-27 17:33 ` Matej Vido
2015-10-27 18:00 ` Thomas Monjalon
2015-11-02 14:26 ` Matej Vido
2015-10-30 12:16 ` Mcnamara, John
2015-11-06 14:34 ` Matej Vido
2015-09-18 8:32 ` [PATCH v2 5/5] doc: update 2.2 release notes Matej Vido
2015-09-24 16:23 ` [PATCH v2] doc: update the dpdk " John McNamara
2015-09-24 21:14 ` Thomas Monjalon
2015-11-10 14:18 ` [PATCH v3 0/6] Virtual PMD using sze2 layer for COMBO cards Matej Vido
2015-11-10 14:18 ` [PATCH v3 1/6] szedata2: add new poll mode driver Matej Vido
2015-11-20 15:04 ` Thomas Monjalon
2015-11-20 19:25 ` Matej Vido
2015-11-21 10:27 ` Thomas Monjalon
2015-11-10 14:18 ` [PATCH v3 2/6] szedata2: add non-scattered RX function Matej Vido
2015-11-10 14:18 ` [PATCH v3 3/6] szedata2: add TX function Matej Vido
2015-11-10 14:18 ` [PATCH v3 4/6] szedata2: add support for scattered packets in RX Matej Vido
2015-11-10 14:18 ` [PATCH v3 5/6] doc: add documentation for szedata2 PMD Matej Vido
2015-11-10 14:55 ` Mcnamara, John
2015-11-10 14:18 ` [PATCH v3 6/6] doc: update 2.2 release notes Matej Vido
2015-11-16 14:22 ` Mcnamara, John
2015-11-20 16:19 ` [PATCH v3 0/6] Virtual PMD using sze2 layer for COMBO cards Thomas Monjalon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1434702301-4509-1-git-send-email-vido@cesnet.cz \
--to=vido@cesnet.cz \
--cc=dev@dpdk.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.