All of lore.kernel.org
 help / color / mirror / Atom feed
From: Olliver Schinagl <oliver@schinagl.nl>
To: Mark Brown <broonie@kernel.org>,
	Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Olliver Schinagl <oliver+list@schinagl.nl>,
	dev@linux-sunxi.org, linux-spi@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org,
	Alexandru Gagniuc <mr.nuke.me@gmail.com>,
	Olliver Schinagl <o.schinagl@ultimaker.com>
Subject: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size
Date: Sat,  8 Aug 2015 21:41:52 +0200	[thread overview]
Message-ID: <1439062912-4405-2-git-send-email-oliver@schinagl.nl> (raw)
In-Reply-To: <1439062912-4405-1-git-send-email-oliver@schinagl.nl>

From: Alexandru Gagniuc <mr.nuke.me@gmail.com>

SPI transfers were limited to one FIFO depth, which is 64 bytes.
This was an artificial limitation, however, as the hardware can handle
much larger bursts. To accommodate this, we enable the interrupt when
the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt
handler. The 3/4 ratio was chosen arbitrarily, with the intention to
reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause
transmission whenever the FIFO is full, so there is no risk of losing
data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to
replenish the FIFO on large SPI bursts. This requires more care in
when the interrupt is left enabled, as this interrupt will continually
trigger when the FIFO is less than 1/4 full, even though we
acknowledge it.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
---
 drivers/spi/spi-sun4i.c | 76 +++++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 67 insertions(+), 9 deletions(-)

diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c
index fbb0a4d..9a30e49 100644
--- a/drivers/spi/spi-sun4i.c
+++ b/drivers/spi/spi-sun4i.c
@@ -46,6 +46,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10
@@ -61,11 +63,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
@@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;
@@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
-	if (len > sspi->len)
-		len = sspi->len;
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	len = min3(len, (int)cnt, sspi->len);
 
 	while (len--) {
 		byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;
@@ -174,8 +207,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);
@@ -273,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC |
+					 SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
@@ -286,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 
@@ -302,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if (!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
 
-- 
2.1.4


WARNING: multiple messages have this Message-ID
From: Olliver Schinagl <oliver-dxLnbx3+1qmEVqv0pETR8A@public.gmane.org>
To: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
	Maxime Ripard
	<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Cc: Olliver Schinagl
	<oliver+list-dxLnbx3+1qmEVqv0pETR8A@public.gmane.org>,
	dev-3kdeTeqwOZ9EV1b7eY7vFQ@public.gmane.org,
	linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	Alexandru Gagniuc
	<mr.nuke.me-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>,
	Olliver Schinagl
	<o.schinagl-U3FVU11NWA554TAoqtyWWQ@public.gmane.org>
Subject: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size
Date: Sat,  8 Aug 2015 21:41:52 +0200	[thread overview]
Message-ID: <1439062912-4405-2-git-send-email-oliver@schinagl.nl> (raw)
In-Reply-To: <1439062912-4405-1-git-send-email-oliver-dxLnbx3+1qmEVqv0pETR8A@public.gmane.org>

From: Alexandru Gagniuc <mr.nuke.me-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

SPI transfers were limited to one FIFO depth, which is 64 bytes.
This was an artificial limitation, however, as the hardware can handle
much larger bursts. To accommodate this, we enable the interrupt when
the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt
handler. The 3/4 ratio was chosen arbitrarily, with the intention to
reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause
transmission whenever the FIFO is full, so there is no risk of losing
data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to
replenish the FIFO on large SPI bursts. This requires more care in
when the interrupt is left enabled, as this interrupt will continually
trigger when the FIFO is less than 1/4 full, even though we
acknowledge it.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Acked-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Signed-off-by: Olliver Schinagl <o.schinagl-U3FVU11NWA554TAoqtyWWQ@public.gmane.org>
---
 drivers/spi/spi-sun4i.c | 76 +++++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 67 insertions(+), 9 deletions(-)

diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c
index fbb0a4d..9a30e49 100644
--- a/drivers/spi/spi-sun4i.c
+++ b/drivers/spi/spi-sun4i.c
@@ -46,6 +46,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10
@@ -61,11 +63,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
@@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;
@@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
-	if (len > sspi->len)
-		len = sspi->len;
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	len = min3(len, (int)cnt, sspi->len);
 
 	while (len--) {
 		byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;
@@ -174,8 +207,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);
@@ -273,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC |
+					 SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
@@ -286,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 
@@ -302,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if (!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
 
-- 
2.1.4

WARNING: multiple messages have this Message-ID
From: oliver@schinagl.nl (Olliver Schinagl)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size
Date: Sat,  8 Aug 2015 21:41:52 +0200	[thread overview]
Message-ID: <1439062912-4405-2-git-send-email-oliver@schinagl.nl> (raw)
In-Reply-To: <1439062912-4405-1-git-send-email-oliver@schinagl.nl>

From: Alexandru Gagniuc <mr.nuke.me@gmail.com>

SPI transfers were limited to one FIFO depth, which is 64 bytes.
This was an artificial limitation, however, as the hardware can handle
much larger bursts. To accommodate this, we enable the interrupt when
the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt
handler. The 3/4 ratio was chosen arbitrarily, with the intention to
reduce the potential number of interrupts.

Since the SUN4I_CTL_TP bit is set, the hardware will pause
transmission whenever the FIFO is full, so there is no risk of losing
data if we can't service the interrupt in time.

For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to
replenish the FIFO on large SPI bursts. This requires more care in
when the interrupt is left enabled, as this interrupt will continually
trigger when the FIFO is less than 1/4 full, even though we
acknowledge it.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
---
 drivers/spi/spi-sun4i.c | 76 +++++++++++++++++++++++++++++++++++++++++++------
 1 file changed, 67 insertions(+), 9 deletions(-)

diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c
index fbb0a4d..9a30e49 100644
--- a/drivers/spi/spi-sun4i.c
+++ b/drivers/spi/spi-sun4i.c
@@ -46,6 +46,8 @@
 #define SUN4I_CTL_TP				BIT(18)
 
 #define SUN4I_INT_CTL_REG		0x0c
+#define SUN4I_INT_CTL_RF_F34			BIT(4)
+#define SUN4I_INT_CTL_TF_E34			BIT(12)
 #define SUN4I_INT_CTL_TC			BIT(16)
 
 #define SUN4I_INT_STA_REG		0x10
@@ -61,11 +63,14 @@
 #define SUN4I_CLK_CTL_CDR1(div)			(((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8)
 #define SUN4I_CLK_CTL_DRS			BIT(12)
 
+#define SUN4I_MAX_XFER_SIZE			0xffffff
+
 #define SUN4I_BURST_CNT_REG		0x20
-#define SUN4I_BURST_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_BURST_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
 
 #define SUN4I_XMIT_CNT_REG		0x24
-#define SUN4I_XMIT_CNT(cnt)			((cnt) & 0xffffff)
+#define SUN4I_XMIT_CNT(cnt)			((cnt) & SUN4I_MAX_XFER_SIZE)
+
 
 #define SUN4I_FIFO_STA_REG		0x28
 #define SUN4I_FIFO_STA_RF_CNT_MASK		0x7f
@@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value)
 	writel(value, sspi->base_addr + reg);
 }
 
+static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG);
+
+	reg >>= SUN4I_FIFO_STA_TF_CNT_BITS;
+
+	return reg & SUN4I_FIFO_STA_TF_CNT_MASK;
+}
+
+static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg |= mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
+static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask)
+{
+	u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG);
+
+	reg &= ~mask;
+	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg);
+}
+
 static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 {
 	u32 reg, cnt;
@@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len)
 
 static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 {
+	u32 cnt;
 	u8 byte;
 
-	if (len > sspi->len)
-		len = sspi->len;
+	/* See how much data we can fit */
+	cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi);
+
+	len = min3(len, (int)cnt, sspi->len);
 
 	while (len--) {
 		byte = sspi->tx_buf ? *sspi->tx_buf++ : 0;
@@ -174,8 +207,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
+	/* This is the maximum SPI burst size supported by the hardware */
+	if (tfr->len > SUN4I_MAX_XFER_SIZE)
 		return -EINVAL;
 
 	reinit_completion(&sspi->done);
@@ -273,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
 
 	/* Enable the interrupts */
-	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
+	sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC |
+					 SUN4I_INT_CTL_RF_F34);
+	/* Only enable Tx FIFO interrupt if we really need it */
+	if (tx_len > SUN4I_FIFO_DEPTH)
+		sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
 
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
@@ -286,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
 
@@ -302,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id)
 	/* Transfer complete */
 	if (status & SUN4I_INT_CTL_TC) {
 		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC);
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
 		complete(&sspi->done);
 		return IRQ_HANDLED;
 	}
 
+	/* Receive FIFO 3/4 full */
+	if (status & SUN4I_INT_CTL_RF_F34) {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+		/* Only clear the interrupt _after_ draining the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34);
+		return IRQ_HANDLED;
+	}
+
+	/* Transmit FIFO 3/4 empty */
+	if (status & SUN4I_INT_CTL_TF_E34) {
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+
+		if (!sspi->len)
+			/* nothing left to transmit */
+			sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34);
+
+		/* Only clear the interrupt _after_ re-seeding the FIFO */
+		sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34);
+
+		return IRQ_HANDLED;
+	}
+
 	return IRQ_NONE;
 }
 
-- 
2.1.4

  reply	other threads:[~2015-08-08 19:42 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-08-08 19:41 Olliver Schinagl
2015-08-08 19:41 ` Olliver Schinagl
2015-08-08 19:41 ` Olliver Schinagl
2015-08-08 19:41 ` Olliver Schinagl [this message]
2015-08-08 19:41   ` Olliver Schinagl
2015-08-08 19:41   ` Olliver Schinagl
2016-07-21 11:27 ` Michael Weiser
2016-07-21 11:27   ` Michael Weiser
2016-07-21 11:27   ` Michael Weiser
2016-07-21 16:31   ` Mark Brown
2016-07-21 16:31     ` Mark Brown
2016-07-21 16:31     ` Mark Brown
2016-07-21 17:27     ` Michael Weiser
2016-07-21 17:27       ` Michael Weiser
2016-07-21 17:27       ` Michael Weiser
     [not found]       ` <20160721172712.GA10640-kvmrdUZdB1uagOi/AmBnLNHuzzzSOjJt@public.gmane.org>
2016-07-21 18:03         ` Olliver Schinagl
2016-07-21 18:15           ` Mark Brown
2016-07-21 18:15             ` Mark Brown
2016-07-21 18:15             ` Mark Brown
2016-07-21 18:20       ` Mark Brown
2016-07-21 18:20         ` Mark Brown
2016-07-21 18:20         ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1439062912-4405-2-git-send-email-oliver@schinagl.nl \
    --to=oliver@schinagl.nl \
    --cc=broonie@kernel.org \
    --cc=dev@linux-sunxi.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=maxime.ripard@free-electrons.com \
    --cc=mr.nuke.me@gmail.com \
    --cc=o.schinagl@ultimaker.com \
    --cc=oliver+list@schinagl.nl \
    --subject='Re: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.