From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S2992668AbbHHTm2 (ORCPT ); Sat, 8 Aug 2015 15:42:28 -0400 Received: from 7of9.schinagl.nl ([88.159.158.68]:51970 "EHLO 7of9.schinagl.nl" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S2992605AbbHHTmH (ORCPT ); Sat, 8 Aug 2015 15:42:07 -0400 From: Olliver Schinagl To: Mark Brown , Maxime Ripard Cc: Olliver Schinagl , dev@linux-sunxi.org, linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, Alexandru Gagniuc , Olliver Schinagl Subject: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size Date: Sat, 8 Aug 2015 21:41:52 +0200 Message-Id: <1439062912-4405-2-git-send-email-oliver@schinagl.nl> X-Mailer: git-send-email 2.1.4 In-Reply-To: <1439062912-4405-1-git-send-email-oliver@schinagl.nl> References: <1439062912-4405-1-git-send-email-oliver@schinagl.nl> Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org From: Alexandru Gagniuc SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts. Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time. For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it. Signed-off-by: Alexandru Gagniuc Acked-by: Maxime Ripard Signed-off-by: Olliver Schinagl --- drivers/spi/spi-sun4i.c | 76 +++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 67 insertions(+), 9 deletions(-) diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c index fbb0a4d..9a30e49 100644 --- a/drivers/spi/spi-sun4i.c +++ b/drivers/spi/spi-sun4i.c @@ -46,6 +46,8 @@ #define SUN4I_CTL_TP BIT(18) #define SUN4I_INT_CTL_REG 0x0c +#define SUN4I_INT_CTL_RF_F34 BIT(4) +#define SUN4I_INT_CTL_TF_E34 BIT(12) #define SUN4I_INT_CTL_TC BIT(16) #define SUN4I_INT_STA_REG 0x10 @@ -61,11 +63,14 @@ #define SUN4I_CLK_CTL_CDR1(div) (((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8) #define SUN4I_CLK_CTL_DRS BIT(12) +#define SUN4I_MAX_XFER_SIZE 0xffffff + #define SUN4I_BURST_CNT_REG 0x20 -#define SUN4I_BURST_CNT(cnt) ((cnt) & 0xffffff) +#define SUN4I_BURST_CNT(cnt) ((cnt) & SUN4I_MAX_XFER_SIZE) #define SUN4I_XMIT_CNT_REG 0x24 -#define SUN4I_XMIT_CNT(cnt) ((cnt) & 0xffffff) +#define SUN4I_XMIT_CNT(cnt) ((cnt) & SUN4I_MAX_XFER_SIZE) + #define SUN4I_FIFO_STA_REG 0x28 #define SUN4I_FIFO_STA_RF_CNT_MASK 0x7f @@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value) writel(value, sspi->base_addr + reg); } +static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG); + + reg >>= SUN4I_FIFO_STA_TF_CNT_BITS; + + return reg & SUN4I_FIFO_STA_TF_CNT_MASK; +} + +static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG); + + reg |= mask; + sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg); +} + +static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG); + + reg &= ~mask; + sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg); +} + static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) { u32 reg, cnt; @@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len) { + u32 cnt; u8 byte; - if (len > sspi->len) - len = sspi->len; + /* See how much data we can fit */ + cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi); + + len = min3(len, (int)cnt, sspi->len); while (len--) { byte = sspi->tx_buf ? *sspi->tx_buf++ : 0; @@ -174,8 +207,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master, int ret = 0; u32 reg; - /* We don't support transfer larger than the FIFO */ - if (tfr->len > SUN4I_FIFO_DEPTH) + /* This is the maximum SPI burst size supported by the hardware */ + if (tfr->len > SUN4I_MAX_XFER_SIZE) return -EINVAL; reinit_completion(&sspi->done); @@ -273,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master, sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH); /* Enable the interrupts */ - sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC); + sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | + SUN4I_INT_CTL_RF_F34); + /* Only enable Tx FIFO interrupt if we really need it */ + if (tx_len > SUN4I_FIFO_DEPTH) + sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34); /* Start the transfer */ reg = sun4i_spi_read(sspi, SUN4I_CTL_REG); @@ -286,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master, goto out; } - sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); - out: sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0); @@ -302,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id) /* Transfer complete */ if (status & SUN4I_INT_CTL_TC) { sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC); + sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); complete(&sspi->done); return IRQ_HANDLED; } + /* Receive FIFO 3/4 full */ + if (status & SUN4I_INT_CTL_RF_F34) { + sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); + /* Only clear the interrupt _after_ draining the FIFO */ + sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34); + return IRQ_HANDLED; + } + + /* Transmit FIFO 3/4 empty */ + if (status & SUN4I_INT_CTL_TF_E34) { + sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH); + + if (!sspi->len) + /* nothing left to transmit */ + sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34); + + /* Only clear the interrupt _after_ re-seeding the FIFO */ + sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34); + + return IRQ_HANDLED; + } + return IRQ_NONE; } -- 2.1.4 From mboxrd@z Thu Jan 1 00:00:00 1970 From: Olliver Schinagl Subject: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size Date: Sat, 8 Aug 2015 21:41:52 +0200 Message-ID: <1439062912-4405-2-git-send-email-oliver@schinagl.nl> References: <1439062912-4405-1-git-send-email-oliver@schinagl.nl> Reply-To: oliver-dxLnbx3+1qmEVqv0pETR8A@public.gmane.org Mime-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Cc: Olliver Schinagl , dev-3kdeTeqwOZ9EV1b7eY7vFQ@public.gmane.org, linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Alexandru Gagniuc , Olliver Schinagl To: Mark Brown , Maxime Ripard Return-path: In-Reply-To: <1439062912-4405-1-git-send-email-oliver-dxLnbx3+1qmEVqv0pETR8A@public.gmane.org> List-Post: , List-Help: , List-Archive: , List-Unsubscribe: , List-Id: linux-spi.vger.kernel.org From: Alexandru Gagniuc SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts. Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time. For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it. Signed-off-by: Alexandru Gagniuc Acked-by: Maxime Ripard Signed-off-by: Olliver Schinagl --- drivers/spi/spi-sun4i.c | 76 +++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 67 insertions(+), 9 deletions(-) diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c index fbb0a4d..9a30e49 100644 --- a/drivers/spi/spi-sun4i.c +++ b/drivers/spi/spi-sun4i.c @@ -46,6 +46,8 @@ #define SUN4I_CTL_TP BIT(18) #define SUN4I_INT_CTL_REG 0x0c +#define SUN4I_INT_CTL_RF_F34 BIT(4) +#define SUN4I_INT_CTL_TF_E34 BIT(12) #define SUN4I_INT_CTL_TC BIT(16) #define SUN4I_INT_STA_REG 0x10 @@ -61,11 +63,14 @@ #define SUN4I_CLK_CTL_CDR1(div) (((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8) #define SUN4I_CLK_CTL_DRS BIT(12) +#define SUN4I_MAX_XFER_SIZE 0xffffff + #define SUN4I_BURST_CNT_REG 0x20 -#define SUN4I_BURST_CNT(cnt) ((cnt) & 0xffffff) +#define SUN4I_BURST_CNT(cnt) ((cnt) & SUN4I_MAX_XFER_SIZE) #define SUN4I_XMIT_CNT_REG 0x24 -#define SUN4I_XMIT_CNT(cnt) ((cnt) & 0xffffff) +#define SUN4I_XMIT_CNT(cnt) ((cnt) & SUN4I_MAX_XFER_SIZE) + #define SUN4I_FIFO_STA_REG 0x28 #define SUN4I_FIFO_STA_RF_CNT_MASK 0x7f @@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value) writel(value, sspi->base_addr + reg); } +static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG); + + reg >>= SUN4I_FIFO_STA_TF_CNT_BITS; + + return reg & SUN4I_FIFO_STA_TF_CNT_MASK; +} + +static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG); + + reg |= mask; + sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg); +} + +static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG); + + reg &= ~mask; + sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg); +} + static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) { u32 reg, cnt; @@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len) { + u32 cnt; u8 byte; - if (len > sspi->len) - len = sspi->len; + /* See how much data we can fit */ + cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi); + + len = min3(len, (int)cnt, sspi->len); while (len--) { byte = sspi->tx_buf ? *sspi->tx_buf++ : 0; @@ -174,8 +207,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master, int ret = 0; u32 reg; - /* We don't support transfer larger than the FIFO */ - if (tfr->len > SUN4I_FIFO_DEPTH) + /* This is the maximum SPI burst size supported by the hardware */ + if (tfr->len > SUN4I_MAX_XFER_SIZE) return -EINVAL; reinit_completion(&sspi->done); @@ -273,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master, sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH); /* Enable the interrupts */ - sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC); + sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | + SUN4I_INT_CTL_RF_F34); + /* Only enable Tx FIFO interrupt if we really need it */ + if (tx_len > SUN4I_FIFO_DEPTH) + sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34); /* Start the transfer */ reg = sun4i_spi_read(sspi, SUN4I_CTL_REG); @@ -286,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master, goto out; } - sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); - out: sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0); @@ -302,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id) /* Transfer complete */ if (status & SUN4I_INT_CTL_TC) { sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC); + sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); complete(&sspi->done); return IRQ_HANDLED; } + /* Receive FIFO 3/4 full */ + if (status & SUN4I_INT_CTL_RF_F34) { + sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); + /* Only clear the interrupt _after_ draining the FIFO */ + sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34); + return IRQ_HANDLED; + } + + /* Transmit FIFO 3/4 empty */ + if (status & SUN4I_INT_CTL_TF_E34) { + sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH); + + if (!sspi->len) + /* nothing left to transmit */ + sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34); + + /* Only clear the interrupt _after_ re-seeding the FIFO */ + sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34); + + return IRQ_HANDLED; + } + return IRQ_NONE; } -- 2.1.4 From mboxrd@z Thu Jan 1 00:00:00 1970 From: oliver@schinagl.nl (Olliver Schinagl) Date: Sat, 8 Aug 2015 21:41:52 +0200 Subject: [PATCH v6] ARM: sun4i: spi: Allow transfers larger than FIFO size In-Reply-To: <1439062912-4405-1-git-send-email-oliver@schinagl.nl> References: <1439062912-4405-1-git-send-email-oliver@schinagl.nl> Message-ID: <1439062912-4405-2-git-send-email-oliver@schinagl.nl> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org From: Alexandru Gagniuc SPI transfers were limited to one FIFO depth, which is 64 bytes. This was an artificial limitation, however, as the hardware can handle much larger bursts. To accommodate this, we enable the interrupt when the Rx FIFO is 3/4 full, and drain the FIFO within the interrupt handler. The 3/4 ratio was chosen arbitrarily, with the intention to reduce the potential number of interrupts. Since the SUN4I_CTL_TP bit is set, the hardware will pause transmission whenever the FIFO is full, so there is no risk of losing data if we can't service the interrupt in time. For the Tx side, enable and use the Tx FIFO 3/4 empty interrupt to replenish the FIFO on large SPI bursts. This requires more care in when the interrupt is left enabled, as this interrupt will continually trigger when the FIFO is less than 1/4 full, even though we acknowledge it. Signed-off-by: Alexandru Gagniuc Acked-by: Maxime Ripard Signed-off-by: Olliver Schinagl --- drivers/spi/spi-sun4i.c | 76 +++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 67 insertions(+), 9 deletions(-) diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c index fbb0a4d..9a30e49 100644 --- a/drivers/spi/spi-sun4i.c +++ b/drivers/spi/spi-sun4i.c @@ -46,6 +46,8 @@ #define SUN4I_CTL_TP BIT(18) #define SUN4I_INT_CTL_REG 0x0c +#define SUN4I_INT_CTL_RF_F34 BIT(4) +#define SUN4I_INT_CTL_TF_E34 BIT(12) #define SUN4I_INT_CTL_TC BIT(16) #define SUN4I_INT_STA_REG 0x10 @@ -61,11 +63,14 @@ #define SUN4I_CLK_CTL_CDR1(div) (((div) & SUN4I_CLK_CTL_CDR1_MASK) << 8) #define SUN4I_CLK_CTL_DRS BIT(12) +#define SUN4I_MAX_XFER_SIZE 0xffffff + #define SUN4I_BURST_CNT_REG 0x20 -#define SUN4I_BURST_CNT(cnt) ((cnt) & 0xffffff) +#define SUN4I_BURST_CNT(cnt) ((cnt) & SUN4I_MAX_XFER_SIZE) #define SUN4I_XMIT_CNT_REG 0x24 -#define SUN4I_XMIT_CNT(cnt) ((cnt) & 0xffffff) +#define SUN4I_XMIT_CNT(cnt) ((cnt) & SUN4I_MAX_XFER_SIZE) + #define SUN4I_FIFO_STA_REG 0x28 #define SUN4I_FIFO_STA_RF_CNT_MASK 0x7f @@ -96,6 +101,31 @@ static inline void sun4i_spi_write(struct sun4i_spi *sspi, u32 reg, u32 value) writel(value, sspi->base_addr + reg); } +static inline u32 sun4i_spi_get_tx_fifo_count(struct sun4i_spi *sspi) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_FIFO_STA_REG); + + reg >>= SUN4I_FIFO_STA_TF_CNT_BITS; + + return reg & SUN4I_FIFO_STA_TF_CNT_MASK; +} + +static inline void sun4i_spi_enable_interrupt(struct sun4i_spi *sspi, u32 mask) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG); + + reg |= mask; + sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg); +} + +static inline void sun4i_spi_disable_interrupt(struct sun4i_spi *sspi, u32 mask) +{ + u32 reg = sun4i_spi_read(sspi, SUN4I_INT_CTL_REG); + + reg &= ~mask; + sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, reg); +} + static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) { u32 reg, cnt; @@ -118,10 +148,13 @@ static inline void sun4i_spi_drain_fifo(struct sun4i_spi *sspi, int len) static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len) { + u32 cnt; u8 byte; - if (len > sspi->len) - len = sspi->len; + /* See how much data we can fit */ + cnt = SUN4I_FIFO_DEPTH - sun4i_spi_get_tx_fifo_count(sspi); + + len = min3(len, (int)cnt, sspi->len); while (len--) { byte = sspi->tx_buf ? *sspi->tx_buf++ : 0; @@ -174,8 +207,8 @@ static int sun4i_spi_transfer_one(struct spi_master *master, int ret = 0; u32 reg; - /* We don't support transfer larger than the FIFO */ - if (tfr->len > SUN4I_FIFO_DEPTH) + /* This is the maximum SPI burst size supported by the hardware */ + if (tfr->len > SUN4I_MAX_XFER_SIZE) return -EINVAL; reinit_completion(&sspi->done); @@ -273,7 +306,11 @@ static int sun4i_spi_transfer_one(struct spi_master *master, sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH); /* Enable the interrupts */ - sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC); + sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TC | + SUN4I_INT_CTL_RF_F34); + /* Only enable Tx FIFO interrupt if we really need it */ + if (tx_len > SUN4I_FIFO_DEPTH) + sun4i_spi_enable_interrupt(sspi, SUN4I_INT_CTL_TF_E34); /* Start the transfer */ reg = sun4i_spi_read(sspi, SUN4I_CTL_REG); @@ -286,8 +323,6 @@ static int sun4i_spi_transfer_one(struct spi_master *master, goto out; } - sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); - out: sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0); @@ -302,10 +337,33 @@ static irqreturn_t sun4i_spi_handler(int irq, void *dev_id) /* Transfer complete */ if (status & SUN4I_INT_CTL_TC) { sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TC); + sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); complete(&sspi->done); return IRQ_HANDLED; } + /* Receive FIFO 3/4 full */ + if (status & SUN4I_INT_CTL_RF_F34) { + sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH); + /* Only clear the interrupt _after_ draining the FIFO */ + sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_RF_F34); + return IRQ_HANDLED; + } + + /* Transmit FIFO 3/4 empty */ + if (status & SUN4I_INT_CTL_TF_E34) { + sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH); + + if (!sspi->len) + /* nothing left to transmit */ + sun4i_spi_disable_interrupt(sspi, SUN4I_INT_CTL_TF_E34); + + /* Only clear the interrupt _after_ re-seeding the FIFO */ + sun4i_spi_write(sspi, SUN4I_INT_STA_REG, SUN4I_INT_CTL_TF_E34); + + return IRQ_HANDLED; + } + return IRQ_NONE; } -- 2.1.4