From: Arnd Bergmann <arnd@arndb.de>
To: linux-wireless@vger.kernel.org
Cc: Rachel Kim <rachel.kim@atmel.com>,
devel@driverdev.osuosl.org, Chris Park <chris.park@atmel.com>,
gregkh@linuxfoundation.org,
Stanislav Kholmanskikh <kholmanskikh.s.s@gmail.com>,
Johnny Kim <johnny.kim@atmel.com>,
linux-kernel@vger.kernel.org, Tony Cho <tony.cho@atmel.com>,
Glen Lee <glen.lee@atmel.com>, Leo Kim <leo.kim@atmel.com>,
Arnd Bergmann <arnd@arndb.de>
Subject: [PATCH 06/19] staging/wilc1000: avoid static definitions in header
Date: Wed, 21 Oct 2015 00:47:25 +0200 [thread overview]
Message-ID: <1445381258-1455986-7-git-send-email-arnd@arndb.de> (raw)
In-Reply-To: <1445381258-1455986-1-git-send-email-arnd@arndb.de>
The wilc_wfi_cfgoperations.h header defines the ieee80211_txrx_stypes
and cipher_suites variables that are only used in wilc_wfi_cfgoperations.c
and should not be shared in a header file.
This moves over all that data into the .c file, and also moves all
the macro definitions from the file that are also not needed here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
drivers/staging/wilc1000/wilc_wfi_cfgoperations.c | 84 +++++++++++++++++++++++
drivers/staging/wilc1000/wilc_wfi_cfgoperations.h | 83 ----------------------
2 files changed, 84 insertions(+), 83 deletions(-)
diff --git a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
index 0ed05aafa5bf..702c40c1df4b 100644
--- a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
+++ b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.c
@@ -17,6 +17,90 @@
#include "host_interface.h"
#include <linux/errno.h>
+/* The following macros describe the bitfield map used by the firmware to determine its 11i mode */
+#define NO_ENCRYPT 0
+#define ENCRYPT_ENABLED BIT(0)
+#define WEP BIT(1)
+#define WEP_EXTENDED BIT(2)
+#define WPA BIT(3)
+#define WPA2 BIT(4)
+#define AES BIT(5)
+#define TKIP BIT(6)
+
+/*Public action frame index IDs*/
+#define FRAME_TYPE_ID 0
+#define ACTION_CAT_ID 24
+#define ACTION_SUBTYPE_ID 25
+#define P2P_PUB_ACTION_SUBTYPE 30
+
+/*Public action frame Attribute IDs*/
+#define ACTION_FRAME 0xd0
+#define GO_INTENT_ATTR_ID 0x04
+#define CHANLIST_ATTR_ID 0x0b
+#define OPERCHAN_ATTR_ID 0x11
+#define PUB_ACTION_ATTR_ID 0x04
+#define P2PELEM_ATTR_ID 0xdd
+
+/*Public action subtype values*/
+#define GO_NEG_REQ 0x00
+#define GO_NEG_RSP 0x01
+#define GO_NEG_CONF 0x02
+#define P2P_INV_REQ 0x03
+#define P2P_INV_RSP 0x04
+#define PUBLIC_ACT_VENDORSPEC 0x09
+#define GAS_INTIAL_REQ 0x0a
+#define GAS_INTIAL_RSP 0x0b
+
+#define INVALID_CHANNEL 0
+
+#define nl80211_SCAN_RESULT_EXPIRE (3 * HZ)
+#define SCAN_RESULT_EXPIRE (40 * HZ)
+
+static const u32 cipher_suites[] = {
+ WLAN_CIPHER_SUITE_WEP40,
+ WLAN_CIPHER_SUITE_WEP104,
+ WLAN_CIPHER_SUITE_TKIP,
+ WLAN_CIPHER_SUITE_CCMP,
+ WLAN_CIPHER_SUITE_AES_CMAC,
+};
+
+static const struct ieee80211_txrx_stypes
+ wilc_wfi_cfg80211_mgmt_types[NUM_NL80211_IFTYPES] = {
+ [NL80211_IFTYPE_STATION] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
+ BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
+ },
+ [NL80211_IFTYPE_AP] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_REASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_PROBE_REQ >> 4) |
+ BIT(IEEE80211_STYPE_DISASSOC >> 4) |
+ BIT(IEEE80211_STYPE_AUTH >> 4) |
+ BIT(IEEE80211_STYPE_DEAUTH >> 4) |
+ BIT(IEEE80211_STYPE_ACTION >> 4)
+ },
+ [NL80211_IFTYPE_P2P_CLIENT] = {
+ .tx = 0xffff,
+ .rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
+ BIT(IEEE80211_STYPE_PROBE_REQ >> 4) |
+ BIT(IEEE80211_STYPE_ASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_REASSOC_REQ >> 4) |
+ BIT(IEEE80211_STYPE_DISASSOC >> 4) |
+ BIT(IEEE80211_STYPE_AUTH >> 4) |
+ BIT(IEEE80211_STYPE_DEAUTH >> 4)
+ }
+};
+
+/* Time to stay on the channel */
+#define WILC_WFI_DWELL_PASSIVE 100
+#define WILC_WFI_DWELL_ACTIVE 40
+
+#define TCP_ACK_FILTER_LINK_SPEED_THRESH 54
+#define DEFAULT_LINK_SPEED 72
+
+
#define IS_MANAGMEMENT 0x100
#define IS_MANAGMEMENT_CALLBACK 0x080
#define IS_MGMT_STATUS_SUCCES 0x040
diff --git a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.h b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.h
index ae2aaea508db..158d98c0eb87 100644
--- a/drivers/staging/wilc1000/wilc_wfi_cfgoperations.h
+++ b/drivers/staging/wilc1000/wilc_wfi_cfgoperations.h
@@ -10,86 +10,6 @@
#define NM_WFI_CFGOPERATIONS
#include "wilc_wfi_netdevice.h"
-/* The following macros describe the bitfield map used by the firmware to determine its 11i mode */
-#define NO_ENCRYPT 0
-#define ENCRYPT_ENABLED BIT(0)
-#define WEP BIT(1)
-#define WEP_EXTENDED BIT(2)
-#define WPA BIT(3)
-#define WPA2 BIT(4)
-#define AES BIT(5)
-#define TKIP BIT(6)
-
-/*Public action frame index IDs*/
-#define FRAME_TYPE_ID 0
-#define ACTION_CAT_ID 24
-#define ACTION_SUBTYPE_ID 25
-#define P2P_PUB_ACTION_SUBTYPE 30
-
-/*Public action frame Attribute IDs*/
-#define ACTION_FRAME 0xd0
-#define GO_INTENT_ATTR_ID 0x04
-#define CHANLIST_ATTR_ID 0x0b
-#define OPERCHAN_ATTR_ID 0x11
-#define PUB_ACTION_ATTR_ID 0x04
-#define P2PELEM_ATTR_ID 0xdd
-
-/*Public action subtype values*/
-#define GO_NEG_REQ 0x00
-#define GO_NEG_RSP 0x01
-#define GO_NEG_CONF 0x02
-#define P2P_INV_REQ 0x03
-#define P2P_INV_RSP 0x04
-#define PUBLIC_ACT_VENDORSPEC 0x09
-#define GAS_INTIAL_REQ 0x0a
-#define GAS_INTIAL_RSP 0x0b
-
-#define INVALID_CHANNEL 0
-
-#define nl80211_SCAN_RESULT_EXPIRE (3 * HZ)
-#define SCAN_RESULT_EXPIRE (40 * HZ)
-
-static const u32 cipher_suites[] = {
- WLAN_CIPHER_SUITE_WEP40,
- WLAN_CIPHER_SUITE_WEP104,
- WLAN_CIPHER_SUITE_TKIP,
- WLAN_CIPHER_SUITE_CCMP,
- WLAN_CIPHER_SUITE_AES_CMAC,
-};
-
-static const struct ieee80211_txrx_stypes
- wilc_wfi_cfg80211_mgmt_types[NUM_NL80211_IFTYPES] = {
- [NL80211_IFTYPE_STATION] = {
- .tx = 0xffff,
- .rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
- BIT(IEEE80211_STYPE_PROBE_REQ >> 4)
- },
- [NL80211_IFTYPE_AP] = {
- .tx = 0xffff,
- .rx = BIT(IEEE80211_STYPE_ASSOC_REQ >> 4) |
- BIT(IEEE80211_STYPE_REASSOC_REQ >> 4) |
- BIT(IEEE80211_STYPE_PROBE_REQ >> 4) |
- BIT(IEEE80211_STYPE_DISASSOC >> 4) |
- BIT(IEEE80211_STYPE_AUTH >> 4) |
- BIT(IEEE80211_STYPE_DEAUTH >> 4) |
- BIT(IEEE80211_STYPE_ACTION >> 4)
- },
- [NL80211_IFTYPE_P2P_CLIENT] = {
- .tx = 0xffff,
- .rx = BIT(IEEE80211_STYPE_ACTION >> 4) |
- BIT(IEEE80211_STYPE_PROBE_REQ >> 4) |
- BIT(IEEE80211_STYPE_ASSOC_REQ >> 4) |
- BIT(IEEE80211_STYPE_REASSOC_REQ >> 4) |
- BIT(IEEE80211_STYPE_DISASSOC >> 4) |
- BIT(IEEE80211_STYPE_AUTH >> 4) |
- BIT(IEEE80211_STYPE_DEAUTH >> 4)
- }
-};
-
-/* Time to stay on the channel */
-#define WILC_WFI_DWELL_PASSIVE 100
-#define WILC_WFI_DWELL_ACTIVE 40
-
struct wireless_dev *wilc_create_wiphy(struct net_device *net);
void wilc_free_wiphy(struct net_device *net);
int WILC_WFI_update_stats(struct wiphy *wiphy, u32 pktlen, u8 changed);
@@ -101,7 +21,4 @@ struct net_device *WILC_WFI_init_mon_interface(const char *name, struct net_devi
void wilc_mgmt_frame_register(struct wiphy *wiphy, struct wireless_dev *wdev,
u16 frame_type, bool reg);
-#define TCP_ACK_FILTER_LINK_SPEED_THRESH 54
-#define DEFAULT_LINK_SPEED 72
-
#endif
--
2.1.0.rc2
next prev parent reply other threads:[~2015-10-20 22:48 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-20 22:47 [PATCH 00/19] staging/wilc1000 cleanups Arnd Bergmann
2015-10-20 22:47 ` [PATCH 01/19] staging/wilc1000: remove unused functions Arnd Bergmann
2015-10-25 1:20 ` Greg KH
2015-10-20 22:47 ` [PATCH 02/19] staging/wilc1000: make symbols static if possible Arnd Bergmann
2015-10-20 22:47 ` [PATCH 03/19] staging/wilc1000: use proper naming for global symbols Arnd Bergmann
2015-10-20 22:47 ` [PATCH 04/19] staging/wilc1000: move extern declarations to headers Arnd Bergmann
2015-10-20 22:47 ` [PATCH 05/19] staging/wilc1000: use NO_SECURITY instead of NO_ENCRYPT Arnd Bergmann
2015-10-20 22:47 ` Arnd Bergmann [this message]
2015-10-20 22:47 ` [PATCH 07/19] staging/wilc1000: remove linux_wlan_{device_power,device_detection} Arnd Bergmann
2015-10-20 22:47 ` [PATCH 08/19] staging/wilc1000: move wilc_wlan_inp_t into struct wilc Arnd Bergmann
2015-10-20 22:47 ` [PATCH 09/19] staging/wilc1000: move init/exit functions to driver files Arnd Bergmann
2015-10-20 22:47 ` [PATCH 10/19] staging/wilc1000: unify device pointer Arnd Bergmann
2015-10-20 22:47 ` [PATCH 11/19] staging/wilc1000: move wilc1000_ops to drivers Arnd Bergmann
2015-10-20 22:47 ` [PATCH 12/19] staging/wilc1000: use device pointer for phy creation Arnd Bergmann
2015-10-20 22:47 ` [PATCH 13/19] staging/wilc1000: move COMPLEMENT_BOOT code to linux_wlan_sdio.c Arnd Bergmann
2015-10-20 22:47 ` [PATCH 14/19] staging/wilc1000: get rid of WILC_SDIO_IRQ_GPIO Arnd Bergmann
2015-10-20 22:47 ` [PATCH 15/19] staging/wilc1000: turn enable_irq/disable_irq into callbacks Arnd Bergmann
2015-10-20 22:47 ` [PATCH 16/19] staging/wilc1000: remove WILC_SDIO/WILC_SPI macros Arnd Bergmann
2015-10-20 22:47 ` [PATCH 17/19] staging/wilc1000: pass hif operations through initialization Arnd Bergmann
2015-10-20 22:47 ` [PATCH 18/19] staging/wilc1000: split out bus specific modules Arnd Bergmann
2015-10-21 14:20 ` [PATCH] fixup! " Arnd Bergmann
2015-10-20 22:47 ` [PATCH 19/19] [RFC] staging/wilc1000: use more regular probing Arnd Bergmann
2015-10-21 10:06 ` [PATCH 00/19] staging/wilc1000 cleanups glen lee
2015-10-21 10:53 ` Arnd Bergmann
2015-10-22 12:23 ` Arnd Bergmann
2015-10-23 1:37 ` glen lee
2015-10-23 7:51 ` Tony Cho
2015-10-27 7:10 ` Tony Cho
2015-11-02 21:34 ` Arnd Bergmann
2015-11-16 14:04 [PATCH 00/19 v5] " Arnd Bergmann
2015-11-16 14:04 ` [PATCH 06/19] staging/wilc1000: avoid static definitions in header Arnd Bergmann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1445381258-1455986-7-git-send-email-arnd@arndb.de \
--to=arnd@arndb.de \
--cc=chris.park@atmel.com \
--cc=devel@driverdev.osuosl.org \
--cc=glen.lee@atmel.com \
--cc=gregkh@linuxfoundation.org \
--cc=johnny.kim@atmel.com \
--cc=kholmanskikh.s.s@gmail.com \
--cc=leo.kim@atmel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=rachel.kim@atmel.com \
--cc=tony.cho@atmel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.