From mboxrd@z Thu Jan 1 00:00:00 1970 From: Laxman Dewangan Subject: [PATCH V4 1/5] DT: mfd: add device-tree binding doc fro PMIC max77620/max20024 Date: Tue, 19 Jan 2016 15:49:39 +0530 Message-ID: <1453198783-28383-2-git-send-email-ldewangan@nvidia.com> References: <1453198783-28383-1-git-send-email-ldewangan@nvidia.com> Mime-Version: 1.0 Content-Type: text/plain Return-path: In-Reply-To: <1453198783-28383-1-git-send-email-ldewangan@nvidia.com> Sender: linux-kernel-owner@vger.kernel.org To: robh+dt@kernel.org, pawel.moll@arm.com, mark.rutland@arm.com, ijc+devicetree@hellion.org.uk, galak@codeaurora.org, linus.walleij@linaro.org, gnurou@gmail.com, lee.jones@linaro.org, broonie@kernel.org, a.zummo@towertech.it, alexandre.belloni@free-electrons.com Cc: lgirdwood@gmail.com, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org, rtc-linux@googlegroups.com, swarren@nvidia.com, treding@nvidia.com, k.kozlowski@samsung.com, vreddytalla@nvidia.com, Laxman Dewangan List-Id: linux-gpio@vger.kernel.org The MAXIM PMIC MAX77620 and MAX20024 are power management IC which supports RTC, GPIO, DCDC/LDO regulators, interrupt, watchdog etc. Add DT binding document for the different functionality of this device. Signed-off-by: Laxman Dewangan Acked-by: Rob Herring --- Changes from V1: - Added units in some of properties. - Change the boolean property to tristate type and detail some of properties. Change from V2: - added unit in period related dt property. Change from V3: None Added Rob's ack. Documentation/devicetree/bindings/mfd/max77620.txt | 397 +++++++++++++++++++++ include/dt-bindings/mfd/max77620.h | 38 ++ 2 files changed, 435 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/max77620.txt create mode 100644 include/dt-bindings/mfd/max77620.h diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt new file mode 100644 index 0000000..46f6aac --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -0,0 +1,397 @@ +* MAX77620 Power management IC from Maxim Semiconductor. + +Required properties: +------------------- +- compatible: Must be one of + "maxim,max77620" or + "maxim,max20024". +- reg: I2C device address. +- interrupt-controller: MAX77620 has internal interrupt controller which + takes the interrupt request from internal sub-blocks like RTC, + regulators, GPIOs as well as external input. +- #interrupt-cells: Should be set to 2 for IRQ number and flags. + The first cell is the IRQ number. IRQ numbers for different interrupt + source of MAX77620 are defined at dt-bindings/mfd/max77620.h + The second cell is the flags, encoded as the trigger masks from binding + document interrupts.txt, using dt-bindings/irq. + +Optional properties: +------------------- +This device also supports the power OFF of system. +Following properties are used for this purpose: +- system-power-controller: Boolean, This device will be use as + system power controller and used for power OFF of system. + Host issue necessary command to PMIC. + + +Optional submodule and their properties: +======================================= + +Flexible power sequence configuration +==================================== +This sub-node configures the Flexible Power Sequnece(FPS) for power ON slot, +power OFF slot and slot period of the device. Device has 3 FPS as FPS0, +FPS1 and FPS2. The details of FPS configuration is provided through +subnode "fps". The details of FPS0, FPS1, FPS2 are provided through the +child node under this subnodes. The FPS number is provided via reg property. + +The property for fps child nodes as: +Required properties: + -reg: FPS number like 0, 1, 2 for FPS0, FPS1 and FPS2 respectively. +Optinal properties: + -maxim,active-fps-time-period-us: Active state FPS time period in + microseconds. + -maxim,suspend-fps-time-period-us: Suspend state FPS time period in + microseconds. + -maxim,fps-enable-input: FPS enable source like EN0, EN1 or SW. The + macros are defined on dt-bindings/mfd/max77620.h for + different enable source. + FPS_EN_SRC_EN0 for EN0 enable source. + FPS_EN_SRC_EN1 for En1 enable source. + FPS_EN_SRC_SW for SW based control. + -maxim,fps-sw-enable: Boolean, applicable if enable input is SW. + If this property present then enable the FPS else + disable FPS. + -maxim,enable-sleep: Boolean, enable sleep when the external control + goes from HIGH to LOW. + -maxim,enable-global-lpm: Boolean, enable global LPM when the external + control goes from HIGH to LOW. + +Here supported time periods by device in microseconds are as follows: +MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. +MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. + +Pinmux and GPIO: +=============== +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer to pinctrl-bindings.txt for details of the common pinctrl +bindings used by client devices, including the meaning of the phrase +"pin configuration node". + +Following are properties which is needed if GPIO and pinmux functionality +is required: + Required properties: + ------------------- + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Number of GPIO cells. Refer to binding document + gpio/gpio.txt + + Optional properties: + -------------------- + Following properties are require if pin control setting is required + at boot. + - pinctrl-names: A pinctrl state named "default" be defined, using + the bindings in pinctrl/pinctrl-binding.txt. + - pinctrl[0...n]: Properties to contain the phandle that refer to + different nodes of pin control settings. These nodes + represents the pin control setting of state 0 to state n. + Each of these nodes contains different subnodes to + represents some desired configuration for a list of pins. + This configuration can include the mux function to select + on those pin(s), and various pin configuration parameters, + such as pull-up, open drain. + + Each subnode have following properties: + Required properties: + - pins: List of pins. Valid values of pins properties + are: gpio0, gpio1, gpio2, gpio3, gpio4, + gpio5, gpio6, gpio7 + + Optional properties: + function, drive-push-pull, drive-open-drain, + bias-pull-up, bias-pull-down. + Definitions are in the pinmux dt binding + devicetree/bindings/pinctrl/pinctrl-bindings.txt + Absence of properties will leave the configuration + on default. + + Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, + sd0-dvs-in, sd1-dvs-in, reference-out + Theres is also customised property for the GPIO1, + GPIO2 and GPIO3. + - maxim,active-fps-source: FPS source for the gpios in + active state of the GPIO. Valid values are + FPS_SRC_0, FPS_SRC_1, FPS_SRC_2 and + FPS_SRC_NONE. Absence of this property will + leave the pin on default. + - maxim,active-fps-power-up-slot: Power up slot on + given FPS for acive state.Valid values are 0 + to 7. + - maxim,active-fps-power-down-slot: Power down slot + on given FPS for active state. Valid values + are 0 t 7. + - maxim,suspend-fps-source: Suspend state FPS source. + - maxim,suspend-fps-power-down-slot: Suspend state + power down slot. + - maxim,suspend-fps-power-up-slot: Suspend state power + up slot. + +Regulators: +=========== +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The node "regulators" +is require if regulator functionality is needed. + +Following are properties of regulator subnode. + + Optional properties: + ------------------- + The input supply of regulators are the optional properties on the + regulator node. The input supply of these regulators are provided + through following properties: + in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. + in-sd1-supply: Input supply for SD1. + in-sd2-supply: Input supply for SD2. + in-sd3-supply: Input supply for SD3. + in-ldo0-1-supply: Input supply for LDO0 and LDO1. + in-ldo2-supply: Input supply for LDO2. + in-ldo3-5-supply: Input supply for LDO3 and LDO5 + in-ldo4-6-supply: Input supply for LDO4 and LDO6. + in-ldo7-8-supply: Input supply for LDO7 and LDO8. + + + Optional sub nodes for regulators: + --------------------------------- + The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a description + of standard properties for these sub-nodes. + Additional optional custom properties are listed below. + maxim,active-fps-source: FPS source. The macros are defined at + dt-bindings/mfd/max77620.h + maxim,shutdown-fps-source: Same as maxim,fps-source, but it + will apply during shutdown of system. + maxim,active-fps-power-up-slot: Active state Power up slot for + rail on given FPS. + maxim,active-fps-power-down-slot: Active state Power down slot + for rail on given FPS. + maxim,suspend-fps-source: Suspend state FPS source of rail. + maxim,suspend-fps-power-up-slot: Suspend state FPS power + up slot. + maxim,suspend-fps-power-down-slot: Suspend state FPS power + down slot. + maxim,enable-group-low-power: Enable Group low power mode. + maxim,enable-sd0-en2-control: Enable EN2 pincontrol for SD0. + This property is only applicable for SD0. + maxim,disable-remote-sense-on-suspend: Boolean, disable + remote sense on suspend and re-enable on resume. + If this property is not there then no change on + configuration. + +Backup Battery: +============== +This sub-node configure charging backup battery of the device. Device +has support of charging the backup battery. The subnode name is +"backup-battery". + +The property for backup-battery child nodes as: +Presense of this child node will enable the backup battery charging. + +Optinal properties: + -maxim,bb-charging-current-microamp: Charging current + setting. + The device supports 50/100/200/400/600/800uA. + If this property is unavailable then it will + charge with 50uA. + -maxim,bb-charging-voltage-microvolt: Charging Voltage Limit Setting. + Device supports 2500000/3000000/3300000/350000uV. + Default will be set to 2500mV. The voltage will be roundoff + to nearest lower side if other than above is configured. + -maxim,bb-output-resister-ohm: Output resistor on Ohm. + Device supports 100/1000/3000/6000 Ohms. + +Low-Battery Monitor: +================== +This sub-node configure low battery monitor configuration registers. +Device has support for low-battery monitor configuration through +child DT node "low-battery-monitor". + +Optinal properties: + - maxim,low-battery-dac: Tristate, enable/disable low battery DAC. + 0 for disable, + 1 for enable, + absence will left configuration to default. + - maxim,low-battery-shutdown: Tristate, enable/disable low battery + shutdown. + 0 for disable, + 1 for enable, + absence will left configuration to default. + - maxim,low-battery-reset: Tristate, enable/disable low battery reset. + 0 for disable, + 1 for enable, + absence will left configuration to default. + +Example: +-------- +#include +... +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + +Example: +-------- +#include +... +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + backup-battery { + maxim,bb-charging-current-microamp = <100>; + maxim,bb-charging-voltage-microvolt = <3000000>; + maxim,bb-output-resister-ohm = <100>; + }; + + fps { + #address-cells = <1>; + #size-cells = <0>; + fps@0 { + reg = <0>; + maxim,fps-time-period-us = <1280>; + maxim,fps-enable-input = ; + }; + + fps@1 { + reg = <1>; + maxim,fps-time-period-us = <2560>; + maxim,fps-enable-input = ; + }; + + fps@2 { + reg = <2>; + maxim,fps-time-period-us = <640>; + maxim,fps-enable-input = ; + }; + }; + + regulators { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + + max77620_sd0: sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,fps-source = ; + regulator-init-mode = ; + }; + + max77620_sd1: sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-init-mode = ; + maxim,fps-source = ; + }; + + max77620_sd2: sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + maxim,fps-source = ; + }; + + max77620_sd3: sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + regulator-init-mode = ; + }; + + max77620_ldo0: ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo1: ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + maxim,fps-source = ; + }; + + max77620_ldo2: ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + maxim,fps-source = ; + }; + + max77620_ldo3: ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + maxim,fps-source = ; + }; + + max77620_ldo4: ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo5: ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + maxim,fps-source = ; + }; + + max77620_ldo6: ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo7: ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo8: ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + maxim,fps-source = ; + }; + }; +}; diff --git a/include/dt-bindings/mfd/max77620.h b/include/dt-bindings/mfd/max77620.h new file mode 100644 index 0000000..8423d1d --- /dev/null +++ b/include/dt-bindings/mfd/max77620.h @@ -0,0 +1,38 @@ +/* + * This header provides macros for MAXIM MAX77620 device bindings. + * + * Copyright (c) 2016, NVIDIA Corporation. + * + * Author: Laxman Dewangan + * + */ + +#ifndef _DT_BINDINGS_MFD_MAX77620_H +#define _DT_BINDINGS_MFD_MAX77620_H + +/* MAX77620 interrupts */ +#define MAX77620_IRQ_TOP_GLBL 0 /* Low-Battery */ +#define MAX77620_IRQ_TOP_SD 1 /* SD power fail */ +#define MAX77620_IRQ_TOP_LDO 2 /* LDO power fail */ +#define MAX77620_IRQ_TOP_GPIO 3 /* GPIO internal int to MAX77620 */ +#define MAX77620_IRQ_TOP_RTC 4 /* RTC */ +#define MAX77620_IRQ_TOP_32K 5 /* 32kHz oscillator */ +#define MAX77620_IRQ_TOP_ONOFF 6 /* ON/OFF oscillator */ +#define MAX77620_IRQ_LBT_MBATLOW 7 /* Thermal alarm status, > 120C */ +#define MAX77620_IRQ_LBT_TJALRM1 8 /* Thermal alarm status, > 120C */ +#define MAX77620_IRQ_LBT_TJALRM2 9 /* Thermal alarm status, > 140C */ + +/* FPS enable -inputs */ +#define FPS_EN_SRC_EN0 0 +#define FPS_EN_SRC_EN1 1 +#define FPS_EN_SRC_SW 2 +#define FPS_EN_SRC_RSVD 3 + +/* FPS source */ +#define FPS_SRC_0 0 +#define FPS_SRC_1 1 +#define FPS_SRC_2 2 +#define FPS_SRC_NONE 3 +#define FPS_SRC_DEF 4 + +#endif -- 2.1.4 From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S932949AbcASKat (ORCPT ); Tue, 19 Jan 2016 05:30:49 -0500 Received: from hqemgate15.nvidia.com ([216.228.121.64]:15274 "EHLO hqemgate15.nvidia.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932712AbcASKal (ORCPT ); Tue, 19 Jan 2016 05:30:41 -0500 X-PGP-Universal: processed; by hqnvupgp08.nvidia.com on Tue, 19 Jan 2016 02:31:53 -0800 From: Laxman Dewangan To: , , , , , , , , , , CC: , , , , , , , , , Laxman Dewangan Subject: [PATCH V4 1/5] DT: mfd: add device-tree binding doc fro PMIC max77620/max20024 Date: Tue, 19 Jan 2016 15:49:39 +0530 Message-ID: <1453198783-28383-2-git-send-email-ldewangan@nvidia.com> X-Mailer: git-send-email 2.1.4 In-Reply-To: <1453198783-28383-1-git-send-email-ldewangan@nvidia.com> References: <1453198783-28383-1-git-send-email-ldewangan@nvidia.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org The MAXIM PMIC MAX77620 and MAX20024 are power management IC which supports RTC, GPIO, DCDC/LDO regulators, interrupt, watchdog etc. Add DT binding document for the different functionality of this device. Signed-off-by: Laxman Dewangan Acked-by: Rob Herring --- Changes from V1: - Added units in some of properties. - Change the boolean property to tristate type and detail some of properties. Change from V2: - added unit in period related dt property. Change from V3: None Added Rob's ack. Documentation/devicetree/bindings/mfd/max77620.txt | 397 +++++++++++++++++++++ include/dt-bindings/mfd/max77620.h | 38 ++ 2 files changed, 435 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/max77620.txt create mode 100644 include/dt-bindings/mfd/max77620.h diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt new file mode 100644 index 0000000..46f6aac --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -0,0 +1,397 @@ +* MAX77620 Power management IC from Maxim Semiconductor. + +Required properties: +------------------- +- compatible: Must be one of + "maxim,max77620" or + "maxim,max20024". +- reg: I2C device address. +- interrupt-controller: MAX77620 has internal interrupt controller which + takes the interrupt request from internal sub-blocks like RTC, + regulators, GPIOs as well as external input. +- #interrupt-cells: Should be set to 2 for IRQ number and flags. + The first cell is the IRQ number. IRQ numbers for different interrupt + source of MAX77620 are defined at dt-bindings/mfd/max77620.h + The second cell is the flags, encoded as the trigger masks from binding + document interrupts.txt, using dt-bindings/irq. + +Optional properties: +------------------- +This device also supports the power OFF of system. +Following properties are used for this purpose: +- system-power-controller: Boolean, This device will be use as + system power controller and used for power OFF of system. + Host issue necessary command to PMIC. + + +Optional submodule and their properties: +======================================= + +Flexible power sequence configuration +==================================== +This sub-node configures the Flexible Power Sequnece(FPS) for power ON slot, +power OFF slot and slot period of the device. Device has 3 FPS as FPS0, +FPS1 and FPS2. The details of FPS configuration is provided through +subnode "fps". The details of FPS0, FPS1, FPS2 are provided through the +child node under this subnodes. The FPS number is provided via reg property. + +The property for fps child nodes as: +Required properties: + -reg: FPS number like 0, 1, 2 for FPS0, FPS1 and FPS2 respectively. +Optinal properties: + -maxim,active-fps-time-period-us: Active state FPS time period in + microseconds. + -maxim,suspend-fps-time-period-us: Suspend state FPS time period in + microseconds. + -maxim,fps-enable-input: FPS enable source like EN0, EN1 or SW. The + macros are defined on dt-bindings/mfd/max77620.h for + different enable source. + FPS_EN_SRC_EN0 for EN0 enable source. + FPS_EN_SRC_EN1 for En1 enable source. + FPS_EN_SRC_SW for SW based control. + -maxim,fps-sw-enable: Boolean, applicable if enable input is SW. + If this property present then enable the FPS else + disable FPS. + -maxim,enable-sleep: Boolean, enable sleep when the external control + goes from HIGH to LOW. + -maxim,enable-global-lpm: Boolean, enable global LPM when the external + control goes from HIGH to LOW. + +Here supported time periods by device in microseconds are as follows: +MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. +MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. + +Pinmux and GPIO: +=============== +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer to pinctrl-bindings.txt for details of the common pinctrl +bindings used by client devices, including the meaning of the phrase +"pin configuration node". + +Following are properties which is needed if GPIO and pinmux functionality +is required: + Required properties: + ------------------- + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Number of GPIO cells. Refer to binding document + gpio/gpio.txt + + Optional properties: + -------------------- + Following properties are require if pin control setting is required + at boot. + - pinctrl-names: A pinctrl state named "default" be defined, using + the bindings in pinctrl/pinctrl-binding.txt. + - pinctrl[0...n]: Properties to contain the phandle that refer to + different nodes of pin control settings. These nodes + represents the pin control setting of state 0 to state n. + Each of these nodes contains different subnodes to + represents some desired configuration for a list of pins. + This configuration can include the mux function to select + on those pin(s), and various pin configuration parameters, + such as pull-up, open drain. + + Each subnode have following properties: + Required properties: + - pins: List of pins. Valid values of pins properties + are: gpio0, gpio1, gpio2, gpio3, gpio4, + gpio5, gpio6, gpio7 + + Optional properties: + function, drive-push-pull, drive-open-drain, + bias-pull-up, bias-pull-down. + Definitions are in the pinmux dt binding + devicetree/bindings/pinctrl/pinctrl-bindings.txt + Absence of properties will leave the configuration + on default. + + Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, + sd0-dvs-in, sd1-dvs-in, reference-out + Theres is also customised property for the GPIO1, + GPIO2 and GPIO3. + - maxim,active-fps-source: FPS source for the gpios in + active state of the GPIO. Valid values are + FPS_SRC_0, FPS_SRC_1, FPS_SRC_2 and + FPS_SRC_NONE. Absence of this property will + leave the pin on default. + - maxim,active-fps-power-up-slot: Power up slot on + given FPS for acive state.Valid values are 0 + to 7. + - maxim,active-fps-power-down-slot: Power down slot + on given FPS for active state. Valid values + are 0 t 7. + - maxim,suspend-fps-source: Suspend state FPS source. + - maxim,suspend-fps-power-down-slot: Suspend state + power down slot. + - maxim,suspend-fps-power-up-slot: Suspend state power + up slot. + +Regulators: +=========== +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The node "regulators" +is require if regulator functionality is needed. + +Following are properties of regulator subnode. + + Optional properties: + ------------------- + The input supply of regulators are the optional properties on the + regulator node. The input supply of these regulators are provided + through following properties: + in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. + in-sd1-supply: Input supply for SD1. + in-sd2-supply: Input supply for SD2. + in-sd3-supply: Input supply for SD3. + in-ldo0-1-supply: Input supply for LDO0 and LDO1. + in-ldo2-supply: Input supply for LDO2. + in-ldo3-5-supply: Input supply for LDO3 and LDO5 + in-ldo4-6-supply: Input supply for LDO4 and LDO6. + in-ldo7-8-supply: Input supply for LDO7 and LDO8. + + + Optional sub nodes for regulators: + --------------------------------- + The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a description + of standard properties for these sub-nodes. + Additional optional custom properties are listed below. + maxim,active-fps-source: FPS source. The macros are defined at + dt-bindings/mfd/max77620.h + maxim,shutdown-fps-source: Same as maxim,fps-source, but it + will apply during shutdown of system. + maxim,active-fps-power-up-slot: Active state Power up slot for + rail on given FPS. + maxim,active-fps-power-down-slot: Active state Power down slot + for rail on given FPS. + maxim,suspend-fps-source: Suspend state FPS source of rail. + maxim,suspend-fps-power-up-slot: Suspend state FPS power + up slot. + maxim,suspend-fps-power-down-slot: Suspend state FPS power + down slot. + maxim,enable-group-low-power: Enable Group low power mode. + maxim,enable-sd0-en2-control: Enable EN2 pincontrol for SD0. + This property is only applicable for SD0. + maxim,disable-remote-sense-on-suspend: Boolean, disable + remote sense on suspend and re-enable on resume. + If this property is not there then no change on + configuration. + +Backup Battery: +============== +This sub-node configure charging backup battery of the device. Device +has support of charging the backup battery. The subnode name is +"backup-battery". + +The property for backup-battery child nodes as: +Presense of this child node will enable the backup battery charging. + +Optinal properties: + -maxim,bb-charging-current-microamp: Charging current + setting. + The device supports 50/100/200/400/600/800uA. + If this property is unavailable then it will + charge with 50uA. + -maxim,bb-charging-voltage-microvolt: Charging Voltage Limit Setting. + Device supports 2500000/3000000/3300000/350000uV. + Default will be set to 2500mV. The voltage will be roundoff + to nearest lower side if other than above is configured. + -maxim,bb-output-resister-ohm: Output resistor on Ohm. + Device supports 100/1000/3000/6000 Ohms. + +Low-Battery Monitor: +================== +This sub-node configure low battery monitor configuration registers. +Device has support for low-battery monitor configuration through +child DT node "low-battery-monitor". + +Optinal properties: + - maxim,low-battery-dac: Tristate, enable/disable low battery DAC. + 0 for disable, + 1 for enable, + absence will left configuration to default. + - maxim,low-battery-shutdown: Tristate, enable/disable low battery + shutdown. + 0 for disable, + 1 for enable, + absence will left configuration to default. + - maxim,low-battery-reset: Tristate, enable/disable low battery reset. + 0 for disable, + 1 for enable, + absence will left configuration to default. + +Example: +-------- +#include +... +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + +Example: +-------- +#include +... +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + backup-battery { + maxim,bb-charging-current-microamp = <100>; + maxim,bb-charging-voltage-microvolt = <3000000>; + maxim,bb-output-resister-ohm = <100>; + }; + + fps { + #address-cells = <1>; + #size-cells = <0>; + fps@0 { + reg = <0>; + maxim,fps-time-period-us = <1280>; + maxim,fps-enable-input = ; + }; + + fps@1 { + reg = <1>; + maxim,fps-time-period-us = <2560>; + maxim,fps-enable-input = ; + }; + + fps@2 { + reg = <2>; + maxim,fps-time-period-us = <640>; + maxim,fps-enable-input = ; + }; + }; + + regulators { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + + max77620_sd0: sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,fps-source = ; + regulator-init-mode = ; + }; + + max77620_sd1: sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-init-mode = ; + maxim,fps-source = ; + }; + + max77620_sd2: sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + maxim,fps-source = ; + }; + + max77620_sd3: sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + regulator-init-mode = ; + }; + + max77620_ldo0: ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo1: ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + maxim,fps-source = ; + }; + + max77620_ldo2: ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + maxim,fps-source = ; + }; + + max77620_ldo3: ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + maxim,fps-source = ; + }; + + max77620_ldo4: ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo5: ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + maxim,fps-source = ; + }; + + max77620_ldo6: ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo7: ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo8: ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + maxim,fps-source = ; + }; + }; +}; diff --git a/include/dt-bindings/mfd/max77620.h b/include/dt-bindings/mfd/max77620.h new file mode 100644 index 0000000..8423d1d --- /dev/null +++ b/include/dt-bindings/mfd/max77620.h @@ -0,0 +1,38 @@ +/* + * This header provides macros for MAXIM MAX77620 device bindings. + * + * Copyright (c) 2016, NVIDIA Corporation. + * + * Author: Laxman Dewangan + * + */ + +#ifndef _DT_BINDINGS_MFD_MAX77620_H +#define _DT_BINDINGS_MFD_MAX77620_H + +/* MAX77620 interrupts */ +#define MAX77620_IRQ_TOP_GLBL 0 /* Low-Battery */ +#define MAX77620_IRQ_TOP_SD 1 /* SD power fail */ +#define MAX77620_IRQ_TOP_LDO 2 /* LDO power fail */ +#define MAX77620_IRQ_TOP_GPIO 3 /* GPIO internal int to MAX77620 */ +#define MAX77620_IRQ_TOP_RTC 4 /* RTC */ +#define MAX77620_IRQ_TOP_32K 5 /* 32kHz oscillator */ +#define MAX77620_IRQ_TOP_ONOFF 6 /* ON/OFF oscillator */ +#define MAX77620_IRQ_LBT_MBATLOW 7 /* Thermal alarm status, > 120C */ +#define MAX77620_IRQ_LBT_TJALRM1 8 /* Thermal alarm status, > 120C */ +#define MAX77620_IRQ_LBT_TJALRM2 9 /* Thermal alarm status, > 140C */ + +/* FPS enable -inputs */ +#define FPS_EN_SRC_EN0 0 +#define FPS_EN_SRC_EN1 1 +#define FPS_EN_SRC_SW 2 +#define FPS_EN_SRC_RSVD 3 + +/* FPS source */ +#define FPS_SRC_0 0 +#define FPS_SRC_1 1 +#define FPS_SRC_2 2 +#define FPS_SRC_NONE 3 +#define FPS_SRC_DEF 4 + +#endif -- 2.1.4 From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: from hqemgate15.nvidia.com (hqemgate15.nvidia.com. [216.228.121.64]) by gmr-mx.google.com with ESMTPS id i25si2958441pfj.2.2016.01.19.02.30.40 for (version=TLS1_2 cipher=ECDHE-RSA-AES128-GCM-SHA256 bits=128/128); Tue, 19 Jan 2016 02:30:41 -0800 (PST) From: Laxman Dewangan To: , , , , , , , , , , CC: , , , , , , , , , Laxman Dewangan Subject: [rtc-linux] [PATCH V4 1/5] DT: mfd: add device-tree binding doc fro PMIC max77620/max20024 Date: Tue, 19 Jan 2016 15:49:39 +0530 Message-ID: <1453198783-28383-2-git-send-email-ldewangan@nvidia.com> In-Reply-To: <1453198783-28383-1-git-send-email-ldewangan@nvidia.com> References: <1453198783-28383-1-git-send-email-ldewangan@nvidia.com> MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Reply-To: rtc-linux@googlegroups.com List-ID: List-Post: , List-Help: , List-Archive: , List-Unsubscribe: , The MAXIM PMIC MAX77620 and MAX20024 are power management IC which supports RTC, GPIO, DCDC/LDO regulators, interrupt, watchdog etc. Add DT binding document for the different functionality of this device. Signed-off-by: Laxman Dewangan Acked-by: Rob Herring --- Changes from V1: - Added units in some of properties. - Change the boolean property to tristate type and detail some of properties. Change from V2: - added unit in period related dt property. Change from V3: None Added Rob's ack. Documentation/devicetree/bindings/mfd/max77620.txt | 397 +++++++++++++++++++++ include/dt-bindings/mfd/max77620.h | 38 ++ 2 files changed, 435 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/max77620.txt create mode 100644 include/dt-bindings/mfd/max77620.h diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt new file mode 100644 index 0000000..46f6aac --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77620.txt @@ -0,0 +1,397 @@ +* MAX77620 Power management IC from Maxim Semiconductor. + +Required properties: +------------------- +- compatible: Must be one of + "maxim,max77620" or + "maxim,max20024". +- reg: I2C device address. +- interrupt-controller: MAX77620 has internal interrupt controller which + takes the interrupt request from internal sub-blocks like RTC, + regulators, GPIOs as well as external input. +- #interrupt-cells: Should be set to 2 for IRQ number and flags. + The first cell is the IRQ number. IRQ numbers for different interrupt + source of MAX77620 are defined at dt-bindings/mfd/max77620.h + The second cell is the flags, encoded as the trigger masks from binding + document interrupts.txt, using dt-bindings/irq. + +Optional properties: +------------------- +This device also supports the power OFF of system. +Following properties are used for this purpose: +- system-power-controller: Boolean, This device will be use as + system power controller and used for power OFF of system. + Host issue necessary command to PMIC. + + +Optional submodule and their properties: +======================================= + +Flexible power sequence configuration +==================================== +This sub-node configures the Flexible Power Sequnece(FPS) for power ON slot, +power OFF slot and slot period of the device. Device has 3 FPS as FPS0, +FPS1 and FPS2. The details of FPS configuration is provided through +subnode "fps". The details of FPS0, FPS1, FPS2 are provided through the +child node under this subnodes. The FPS number is provided via reg property. + +The property for fps child nodes as: +Required properties: + -reg: FPS number like 0, 1, 2 for FPS0, FPS1 and FPS2 respectively. +Optinal properties: + -maxim,active-fps-time-period-us: Active state FPS time period in + microseconds. + -maxim,suspend-fps-time-period-us: Suspend state FPS time period in + microseconds. + -maxim,fps-enable-input: FPS enable source like EN0, EN1 or SW. The + macros are defined on dt-bindings/mfd/max77620.h for + different enable source. + FPS_EN_SRC_EN0 for EN0 enable source. + FPS_EN_SRC_EN1 for En1 enable source. + FPS_EN_SRC_SW for SW based control. + -maxim,fps-sw-enable: Boolean, applicable if enable input is SW. + If this property present then enable the FPS else + disable FPS. + -maxim,enable-sleep: Boolean, enable sleep when the external control + goes from HIGH to LOW. + -maxim,enable-global-lpm: Boolean, enable global LPM when the external + control goes from HIGH to LOW. + +Here supported time periods by device in microseconds are as follows: +MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds. +MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds. + +Pinmux and GPIO: +=============== +Device has 8 GPIO pins which can be configured as GPIO as well as the +special IO functions. + +Please refer to pinctrl-bindings.txt for details of the common pinctrl +bindings used by client devices, including the meaning of the phrase +"pin configuration node". + +Following are properties which is needed if GPIO and pinmux functionality +is required: + Required properties: + ------------------- + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Number of GPIO cells. Refer to binding document + gpio/gpio.txt + + Optional properties: + -------------------- + Following properties are require if pin control setting is required + at boot. + - pinctrl-names: A pinctrl state named "default" be defined, using + the bindings in pinctrl/pinctrl-binding.txt. + - pinctrl[0...n]: Properties to contain the phandle that refer to + different nodes of pin control settings. These nodes + represents the pin control setting of state 0 to state n. + Each of these nodes contains different subnodes to + represents some desired configuration for a list of pins. + This configuration can include the mux function to select + on those pin(s), and various pin configuration parameters, + such as pull-up, open drain. + + Each subnode have following properties: + Required properties: + - pins: List of pins. Valid values of pins properties + are: gpio0, gpio1, gpio2, gpio3, gpio4, + gpio5, gpio6, gpio7 + + Optional properties: + function, drive-push-pull, drive-open-drain, + bias-pull-up, bias-pull-down. + Definitions are in the pinmux dt binding + devicetree/bindings/pinctrl/pinctrl-bindings.txt + Absence of properties will leave the configuration + on default. + + Valid values for function properties are: + gpio, lpm-control-in, fps-out, 32k-out, + sd0-dvs-in, sd1-dvs-in, reference-out + Theres is also customised property for the GPIO1, + GPIO2 and GPIO3. + - maxim,active-fps-source: FPS source for the gpios in + active state of the GPIO. Valid values are + FPS_SRC_0, FPS_SRC_1, FPS_SRC_2 and + FPS_SRC_NONE. Absence of this property will + leave the pin on default. + - maxim,active-fps-power-up-slot: Power up slot on + given FPS for acive state.Valid values are 0 + to 7. + - maxim,active-fps-power-down-slot: Power down slot + on given FPS for active state. Valid values + are 0 t 7. + - maxim,suspend-fps-source: Suspend state FPS source. + - maxim,suspend-fps-power-down-slot: Suspend state + power down slot. + - maxim,suspend-fps-power-up-slot: Suspend state power + up slot. + +Regulators: +=========== +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The node "regulators" +is require if regulator functionality is needed. + +Following are properties of regulator subnode. + + Optional properties: + ------------------- + The input supply of regulators are the optional properties on the + regulator node. The input supply of these regulators are provided + through following properties: + in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. + in-sd1-supply: Input supply for SD1. + in-sd2-supply: Input supply for SD2. + in-sd3-supply: Input supply for SD3. + in-ldo0-1-supply: Input supply for LDO0 and LDO1. + in-ldo2-supply: Input supply for LDO2. + in-ldo3-5-supply: Input supply for LDO3 and LDO5 + in-ldo4-6-supply: Input supply for LDO4 and LDO6. + in-ldo7-8-supply: Input supply for LDO7 and LDO8. + + + Optional sub nodes for regulators: + --------------------------------- + The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a description + of standard properties for these sub-nodes. + Additional optional custom properties are listed below. + maxim,active-fps-source: FPS source. The macros are defined at + dt-bindings/mfd/max77620.h + maxim,shutdown-fps-source: Same as maxim,fps-source, but it + will apply during shutdown of system. + maxim,active-fps-power-up-slot: Active state Power up slot for + rail on given FPS. + maxim,active-fps-power-down-slot: Active state Power down slot + for rail on given FPS. + maxim,suspend-fps-source: Suspend state FPS source of rail. + maxim,suspend-fps-power-up-slot: Suspend state FPS power + up slot. + maxim,suspend-fps-power-down-slot: Suspend state FPS power + down slot. + maxim,enable-group-low-power: Enable Group low power mode. + maxim,enable-sd0-en2-control: Enable EN2 pincontrol for SD0. + This property is only applicable for SD0. + maxim,disable-remote-sense-on-suspend: Boolean, disable + remote sense on suspend and re-enable on resume. + If this property is not there then no change on + configuration. + +Backup Battery: +============== +This sub-node configure charging backup battery of the device. Device +has support of charging the backup battery. The subnode name is +"backup-battery". + +The property for backup-battery child nodes as: +Presense of this child node will enable the backup battery charging. + +Optinal properties: + -maxim,bb-charging-current-microamp: Charging current + setting. + The device supports 50/100/200/400/600/800uA. + If this property is unavailable then it will + charge with 50uA. + -maxim,bb-charging-voltage-microvolt: Charging Voltage Limit Setting. + Device supports 2500000/3000000/3300000/350000uV. + Default will be set to 2500mV. The voltage will be roundoff + to nearest lower side if other than above is configured. + -maxim,bb-output-resister-ohm: Output resistor on Ohm. + Device supports 100/1000/3000/6000 Ohms. + +Low-Battery Monitor: +================== +This sub-node configure low battery monitor configuration registers. +Device has support for low-battery monitor configuration through +child DT node "low-battery-monitor". + +Optinal properties: + - maxim,low-battery-dac: Tristate, enable/disable low battery DAC. + 0 for disable, + 1 for enable, + absence will left configuration to default. + - maxim,low-battery-shutdown: Tristate, enable/disable low battery + shutdown. + 0 for disable, + 1 for enable, + absence will left configuration to default. + - maxim,low-battery-reset: Tristate, enable/disable low battery reset. + 0 for disable, + 1 for enable, + absence will left configuration to default. + +Example: +-------- +#include +... +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + +Example: +-------- +#include +... +max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + + interrupt-parent = <&intc>; + interrupts = <0 86 IRQ_TYPE_NONE>; + + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + backup-battery { + maxim,bb-charging-current-microamp = <100>; + maxim,bb-charging-voltage-microvolt = <3000000>; + maxim,bb-output-resister-ohm = <100>; + }; + + fps { + #address-cells = <1>; + #size-cells = <0>; + fps@0 { + reg = <0>; + maxim,fps-time-period-us = <1280>; + maxim,fps-enable-input = ; + }; + + fps@1 { + reg = <1>; + maxim,fps-time-period-us = <2560>; + maxim,fps-enable-input = ; + }; + + fps@2 { + reg = <2>; + maxim,fps-time-period-us = <640>; + maxim,fps-enable-input = ; + }; + }; + + regulators { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + + max77620_sd0: sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,fps-source = ; + regulator-init-mode = ; + }; + + max77620_sd1: sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + regulator-init-mode = ; + maxim,fps-source = ; + }; + + max77620_sd2: sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + maxim,fps-source = ; + }; + + max77620_sd3: sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + regulator-init-mode = ; + }; + + max77620_ldo0: ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo1: ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + maxim,fps-source = ; + }; + + max77620_ldo2: ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + maxim,fps-source = ; + }; + + max77620_ldo3: ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + maxim,fps-source = ; + }; + + max77620_ldo4: ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo5: ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + maxim,fps-source = ; + }; + + max77620_ldo6: ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo7: ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + maxim,fps-source = ; + }; + + max77620_ldo8: ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + maxim,fps-source = ; + }; + }; +}; diff --git a/include/dt-bindings/mfd/max77620.h b/include/dt-bindings/mfd/max77620.h new file mode 100644 index 0000000..8423d1d --- /dev/null +++ b/include/dt-bindings/mfd/max77620.h @@ -0,0 +1,38 @@ +/* + * This header provides macros for MAXIM MAX77620 device bindings. + * + * Copyright (c) 2016, NVIDIA Corporation. + * + * Author: Laxman Dewangan + * + */ + +#ifndef _DT_BINDINGS_MFD_MAX77620_H +#define _DT_BINDINGS_MFD_MAX77620_H + +/* MAX77620 interrupts */ +#define MAX77620_IRQ_TOP_GLBL 0 /* Low-Battery */ +#define MAX77620_IRQ_TOP_SD 1 /* SD power fail */ +#define MAX77620_IRQ_TOP_LDO 2 /* LDO power fail */ +#define MAX77620_IRQ_TOP_GPIO 3 /* GPIO internal int to MAX77620 */ +#define MAX77620_IRQ_TOP_RTC 4 /* RTC */ +#define MAX77620_IRQ_TOP_32K 5 /* 32kHz oscillator */ +#define MAX77620_IRQ_TOP_ONOFF 6 /* ON/OFF oscillator */ +#define MAX77620_IRQ_LBT_MBATLOW 7 /* Thermal alarm status, > 120C */ +#define MAX77620_IRQ_LBT_TJALRM1 8 /* Thermal alarm status, > 120C */ +#define MAX77620_IRQ_LBT_TJALRM2 9 /* Thermal alarm status, > 140C */ + +/* FPS enable -inputs */ +#define FPS_EN_SRC_EN0 0 +#define FPS_EN_SRC_EN1 1 +#define FPS_EN_SRC_SW 2 +#define FPS_EN_SRC_RSVD 3 + +/* FPS source */ +#define FPS_SRC_0 0 +#define FPS_SRC_1 1 +#define FPS_SRC_2 2 +#define FPS_SRC_NONE 3 +#define FPS_SRC_DEF 4 + +#endif -- 2.1.4 -- -- You received this message because you are subscribed to "rtc-linux". Membership options at http://groups.google.com/group/rtc-linux . Please read http://groups.google.com/group/rtc-linux/web/checklist before submitting a driver. --- You received this message because you are subscribed to the Google Groups "rtc-linux" group. To unsubscribe from this group and stop receiving emails from it, send an email to rtc-linux+unsubscribe@googlegroups.com. For more options, visit https://groups.google.com/d/optout.