* [PATCH v3 1/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
@ 2016-06-12 11:07 ` Hans de Goede
0 siblings, 0 replies; 6+ messages in thread
From: Hans de Goede @ 2016-06-12 11:07 UTC (permalink / raw)
To: Chen-Yu Tsai, Maxime Ripard
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree,
Hans de Goede
Add pmic / regulator nodes to Mele A1000G quad dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
Changes in v2:
-Add a bit to the commit msg explaining why dldo4 is marked regulator-always-on
Changes in v3:
-Also add a comment explaining why dldo4 is marked regulator-always-on
---
arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts | 93 +++++++++++++++++++++++-
1 file changed, 92 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
index e063dab..5faeae4 100644
--- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
+++ b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
@@ -72,6 +72,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
@@ -85,6 +89,7 @@
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy@1 {
@@ -101,13 +106,26 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins@0 {
allwinner,pins = "PH13";
@@ -131,6 +149,78 @@
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
@@ -151,5 +241,6 @@
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 1/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
@ 2016-06-12 11:07 ` Hans de Goede
0 siblings, 0 replies; 6+ messages in thread
From: Hans de Goede @ 2016-06-12 11:07 UTC (permalink / raw)
To: linux-arm-kernel
Add pmic / regulator nodes to Mele A1000G quad dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
-Add a bit to the commit msg explaining why dldo4 is marked regulator-always-on
Changes in v3:
-Also add a comment explaining why dldo4 is marked regulator-always-on
---
arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts | 93 +++++++++++++++++++++++-
1 file changed, 92 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
index e063dab..5faeae4 100644
--- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
+++ b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
@@ -72,6 +72,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
@@ -85,6 +89,7 @@
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy at 1 {
@@ -101,13 +106,26 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic at 68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins at 0 {
allwinner,pins = "PH13";
@@ -131,6 +149,78 @@
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
@@ -151,5 +241,6 @@
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
2016-06-12 11:07 ` Hans de Goede
@ 2016-06-12 11:07 ` Hans de Goede
-1 siblings, 0 replies; 6+ messages in thread
From: Hans de Goede @ 2016-06-12 11:07 UTC (permalink / raw)
To: Chen-Yu Tsai, Maxime Ripard
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree,
Hans de Goede
Add pmic / regulator nodes to Mele M9 dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
Changes in v2:
-Add a bit to the commit msg explaining why dldo4 is marked regulator-always-on
Changes in v3:
-Also add a comment explaining why dldo4 is marked regulator-always-on
---
arch/arm/boot/dts/sun6i-a31-m9.dts | 93 +++++++++++++++++++++++++++++++++++++-
1 file changed, 92 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/sun6i-a31-m9.dts
index 66d29b8..29016a1 100644
--- a/arch/arm/boot/dts/sun6i-a31-m9.dts
+++ b/arch/arm/boot/dts/sun6i-a31-m9.dts
@@ -72,6 +72,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
@@ -85,6 +89,7 @@
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy@1 {
@@ -101,13 +106,26 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins@0 {
allwinner,pins = "PH13";
@@ -131,6 +149,78 @@
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
@@ -146,5 +236,6 @@
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
@ 2016-06-12 11:07 ` Hans de Goede
0 siblings, 0 replies; 6+ messages in thread
From: Hans de Goede @ 2016-06-12 11:07 UTC (permalink / raw)
To: linux-arm-kernel
Add pmic / regulator nodes to Mele M9 dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
-Add a bit to the commit msg explaining why dldo4 is marked regulator-always-on
Changes in v3:
-Also add a comment explaining why dldo4 is marked regulator-always-on
---
arch/arm/boot/dts/sun6i-a31-m9.dts | 93 +++++++++++++++++++++++++++++++++++++-
1 file changed, 92 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/sun6i-a31-m9.dts
index 66d29b8..29016a1 100644
--- a/arch/arm/boot/dts/sun6i-a31-m9.dts
+++ b/arch/arm/boot/dts/sun6i-a31-m9.dts
@@ -72,6 +72,10 @@
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
@@ -85,6 +89,7 @@
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy at 1 {
@@ -101,13 +106,26 @@
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic at 68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins at 0 {
allwinner,pins = "PH13";
@@ -131,6 +149,78 @@
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
@@ -146,5 +236,6 @@
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 1/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
2016-06-12 11:07 ` Hans de Goede
@ 2016-06-13 8:18 ` Maxime Ripard
-1 siblings, 0 replies; 6+ messages in thread
From: Maxime Ripard @ 2016-06-13 8:18 UTC (permalink / raw)
To: Hans de Goede
Cc: Chen-Yu Tsai, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree
[-- Attachment #1: Type: text/plain, Size: 541 bytes --]
On Sun, Jun 12, 2016 at 01:07:00PM +0200, Hans de Goede wrote:
> Add pmic / regulator nodes to Mele A1000G quad dts.
>
> Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
> to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
> marked as regulator-always-on.
>
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Applied both, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
@ 2016-06-13 8:18 ` Maxime Ripard
0 siblings, 0 replies; 6+ messages in thread
From: Maxime Ripard @ 2016-06-13 8:18 UTC (permalink / raw)
To: linux-arm-kernel
On Sun, Jun 12, 2016 at 01:07:00PM +0200, Hans de Goede wrote:
> Add pmic / regulator nodes to Mele A1000G quad dts.
>
> Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
> to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
> marked as regulator-always-on.
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Applied both, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20160613/468ecfda/attachment.sig>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-06-13 8:18 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-12 11:07 [PATCH v3 1/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts Hans de Goede
2016-06-12 11:07 ` Hans de Goede
[not found] ` <1465729621-27378-1-git-send-email-hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
2016-06-12 11:07 ` [PATCH v3 2/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts Hans de Goede
2016-06-12 11:07 ` Hans de Goede
2016-06-13 8:18 ` [PATCH v3 1/2] ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts Maxime Ripard
2016-06-13 8:18 ` Maxime Ripard
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.