From mboxrd@z Thu Jan 1 00:00:00 1970 From: Wenzhuo Lu Subject: [PATCH] app/testpmd: fix DCB config issue on ixgbe Date: Fri, 5 Aug 2016 13:20:29 +0800 Message-ID: <1470374429-14848-1-git-send-email-wenzhuo.lu@intel.com> Cc: pablo.de.lara.guarch@intel.com, Wenzhuo Lu To: dev@dpdk.org Return-path: Received: from mga03.intel.com (mga03.intel.com [134.134.136.65]) by dpdk.org (Postfix) with ESMTP id 2899E2B98 for ; Fri, 5 Aug 2016 07:20:38 +0200 (CEST) List-Id: patches and discussions about DPDK List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Errors-To: dev-bounces@dpdk.org Sender: "dev" An issue is found that DCB cannot be configured on ixgbe NICs. It's said the TX queue number is not right. On ixgbe the max TX queue number is not fixed, it depends on the multi-queue mode. This patch adds the device configuration before getting info in the DCB configuration process. So the right info can be got depending on the configuration. Fixes: 96c0450dff86 (ixgbe: fix dropping packets from unsupported Tx queues) Signed-off-by: Wenzhuo Lu --- app/test-pmd/testpmd.c | 39 +++++++++++++++++++++------------------ 1 file changed, 21 insertions(+), 18 deletions(-) diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c index 1428974..ba41bea 100644 --- a/app/test-pmd/testpmd.c +++ b/app/test-pmd/testpmd.c @@ -1962,17 +1962,30 @@ init_port_dcb_config(portid_t pid, uint8_t pfc_en) { struct rte_eth_conf port_conf; - struct rte_eth_dev_info dev_info; struct rte_port *rte_port; int retval; uint16_t i; - rte_eth_dev_info_get(pid, &dev_info); + rte_port = &ports[pid]; + + memset(&port_conf, 0, sizeof(struct rte_eth_conf)); + /* Enter DCB configuration status */ + dcb_config = 1; + + /*set configuration of DCB in vt mode and DCB in non-vt mode*/ + retval = get_eth_dcb_conf(&port_conf, dcb_mode, num_tcs, pfc_en); + if (retval < 0) + return retval; + port_conf.rxmode.hw_vlan_filter = 1; + + (void)rte_eth_dev_configure(pid, 0, 0, &port_conf); + rte_eth_dev_info_get(pid, &rte_port->dev_info); /* If dev_info.vmdq_pool_base is greater than 0, * the queue id of vmdq pools is started after pf queues. */ - if (dcb_mode == DCB_VT_ENABLED && dev_info.vmdq_pool_base > 0) { + if (dcb_mode == DCB_VT_ENABLED && + rte_port->dev_info.vmdq_pool_base > 0) { printf("VMDQ_DCB multi-queue mode is nonsensical" " for port %d.", pid); return -1; @@ -1982,13 +1995,13 @@ init_port_dcb_config(portid_t pid, * and has the same number of rxq and txq in dcb mode */ if (dcb_mode == DCB_VT_ENABLED) { - nb_rxq = dev_info.max_rx_queues; - nb_txq = dev_info.max_tx_queues; + nb_rxq = rte_port->dev_info.max_rx_queues; + nb_txq = rte_port->dev_info.max_tx_queues; } else { /*if vt is disabled, use all pf queues */ - if (dev_info.vmdq_pool_base == 0) { - nb_rxq = dev_info.max_rx_queues; - nb_txq = dev_info.max_tx_queues; + if (rte_port->dev_info.vmdq_pool_base == 0) { + nb_rxq = rte_port->dev_info.max_rx_queues; + nb_txq = rte_port->dev_info.max_tx_queues; } else { nb_rxq = (queueid_t)num_tcs; nb_txq = (queueid_t)num_tcs; @@ -1997,16 +2010,6 @@ init_port_dcb_config(portid_t pid, } rx_free_thresh = 64; - memset(&port_conf, 0, sizeof(struct rte_eth_conf)); - /* Enter DCB configuration status */ - dcb_config = 1; - - /*set configuration of DCB in vt mode and DCB in non-vt mode*/ - retval = get_eth_dcb_conf(&port_conf, dcb_mode, num_tcs, pfc_en); - if (retval < 0) - return retval; - - rte_port = &ports[pid]; memcpy(&rte_port->dev_conf, &port_conf, sizeof(struct rte_eth_conf)); rxtx_port_config(rte_port); -- 1.9.3