From mboxrd@z Thu Jan 1 00:00:00 1970 From: Aaron Conole Subject: [PATCH v10] virtio-net: add Max MTU configuration field Date: Tue, 13 Sep 2016 11:18:12 -0400 Message-ID: <1473779892-6234-1-git-send-email-aconole__23813.9074914672$1473779917$gmane$org@redhat.com> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: virtualization-bounces@lists.linux-foundation.org Errors-To: virtualization-bounces@lists.linux-foundation.org To: virtio-dev@lists.oasis-open.org, virtualization@lists.linux-foundation.org Cc: Victor Kaplansky , Maxime Coquelin , "Michael S. Tsirkin" List-Id: virtualization@lists.linuxfoundation.org It is helpful for a host to indicate it's MTU to be set on guest NICs other than the assumed 1500 byte value. This helps in situations where the host network is using Jumbo Frames, or aiding in PMTU discovery by configuring a homogenous network. It is also helpful for sizing receive buffers correctly. The change adds a new field to configuration area of network devices. It will be used to pass a maximum MTU from the device to the driver. This will be used by the driver as a maximum value for packet sizes during transmission, without segmentation offloading. In addition, in order to support backward and forward compatibility, we introduce a new feature bit called VIRTIO_NET_F_MTU. VIRTIO-152 Signed-off-by: Aaron Conole Cc: Victor Kaplansky Acked-by: Michael S. Tsirkin Acked-by: Maxime Coquelin --- v1: This is an attempt at continuing the work done by Victor Kaplansky on mtu negiotiation for virtio-net devices. It attempts to pick up from https://lists.oasis-open.org/archives/virtio-dev/201508/msg00007.html and is just a minor blurb from the first patch along with the 2nd patch from the series, and some of the feedback integrated. v2: Rephrase and provide a mechanism for guest->host and host->guest communication through a driver read-only and driver write-only field. v3: Converted to just support initial MTU. Guest->host and Host->guest MTU changes are outside the scope of this change. v4: Removed references to 'initial', since that condition cannot be tested. Simply state that if the driver will use the mtu field, it must negotiate the feature bit, and if not, it must not. v5: After feedback from Michael S. Tsirkin v6: Bit has to change to bit 25 due to an undocumented bit 24 being taken. v7: Partial rewrite with feedback from MST. Additional conformance statements added. v8: Clarified the new conformance statements. v9: Updated the commit log for correctness. Added ACKs from Michael S. Tsirkin, and Maxime Coquelin. Included the virtio issue id. v10: Update the conformance statement wordings from previous 'offered' form to 'succesfully negotiated' form. content.tex | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/content.tex b/content.tex index 4b45678..42c0568 100644 --- a/content.tex +++ b/content.tex @@ -3049,6 +3049,11 @@ features. \item[VIRTIO_NET_F_CTRL_GUEST_OFFLOADS (2)] Control channel offloads reconfiguration support. +\item[VIRTIO_NET_F_MTU(3)] Maximum negotiated MTU is supported. If + offered by the device, device advises driver about the value of + MTU to be used. If negotiated, the driver uses \field{mtu} as + the maximum MTU value supplied to the driver. + \item[VIRTIO_NET_F_MAC (5)] Device has given MAC address. \item[VIRTIO_NET_F_GUEST_TSO4 (7)] Driver can receive TSOv4. @@ -3140,11 +3145,16 @@ of each of transmit and receive virtqueues (receiveq1\ldots receiveqN and transmitq1\ldots transmitqN respectively) that can be configured once VIRTIO_NET_F_MQ is negotiated. +The following driver-read-only field, \field{mtu} only exists if +VIRTIO_NET_F_MTU is set. This field specifies the maximum MTU for the driver to +use. + \begin{lstlisting} struct virtio_net_config { u8 mac[6]; le16 status; le16 max_virtqueue_pairs; + le16 mtu; }; \end{lstlisting} @@ -3153,6 +3163,19 @@ struct virtio_net_config { The device MUST set \field{max_virtqueue_pairs} to between 1 and 0x8000 inclusive, if it offers VIRTIO_NET_F_MQ. +The device MUST set \field{mtu} to between 68 and 65535 inclusive, +if it offers VIRTIO_NET_F_MTU. + +The device MUST NOT modify \field{mtu} once it has been set. + +The device MUST NOT pass received packets that exceed \field{mtu} size +with \field{gso_type} NONE or ECN after VIRTIO_NET_F_MTU has been successfully +negotiated. + +The device MUST forward transmitted packets of up to MTU size with +\field{gso_type} NONE or ECN, and do so without fragmentation, after +VIRTIO_NET_F_MTU has been successfully negotiated. + \drivernormative{\subsubsection}{Device configuration layout}{Device Types / Network Device / Device configuration layout} A driver SHOULD negotiate VIRTIO_NET_F_MAC if the device offers it. @@ -3165,6 +3188,15 @@ If the driver does not negotiate the VIRTIO_NET_F_STATUS feature, it SHOULD assume the link is active, otherwise it SHOULD read the link status from the bottom bit of \field{status}. +A driver SHOULD negotiate VIRTIO_NET_F_MTU if the device offers it. + +If the driver negotiates VIRTIO_NET_F_MTU, it MUST supply enough receive +buffers of size \field{mtu} to be able to receive at least one receive +packet with \field{gso_type} NONE or ECN. + +If the driver negotiates VIRTIO_NET_F_MTU, it MUST NOT transmit packets of +size exceeding the value of \field{mtu} with \field{gso_type} NONE or ECN + \subsubsection{Legacy Interface: Device configuration layout}\label{sec:Device Types / Network Device / Device configuration layout / Legacy Interface: Device configuration layout} \label{sec:Device Types / Block Device / Feature bits / Device configuration layout / Legacy Interface: Device configuration layout} When using the legacy interface, transitional devices and drivers -- 2.7.4