[PATCH] net/ixgbe: ensure link status is updated

[Laurent Hardy <laurent.hardy@6wind.com>]

In case of link speed set to 1Gb at peer side (with autoneg or with
defined speed) and cable not plugged-in when device is configured
and started, then link status is not updated properly with new speed
as no link setup is triggered.

To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link
setup each time link_update() is triggered and current link status is
down. When cable is plugged-in, link setup will be performed via
ixgbe_setup_link().

Signed-off-by: Laurent Hardy <laurent.hardy@6wind.com>
---
 drivers/net/ixgbe/ixgbe_ethdev.c |   20 ++++++++++++++++++++
 drivers/net/ixgbe/ixgbe_ethdev.h |    1 +
 2 files changed, 21 insertions(+)

diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
index 52ebbe4..513d1d5 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.c
+++ b/drivers/net/ixgbe/ixgbe_ethdev.c
@@ -2095,6 +2095,7 @@ ixgbe_dev_configure(struct rte_eth_dev *dev)
 
 	/* set flag to update link status after init */
 	intr->flags |= IXGBE_FLAG_NEED_LINK_UPDATE;
+	intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
 
 	/*
 	 * Initialize to TRUE. If any of Rx queues doesn't meet the bulk
@@ -3117,8 +3118,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
 	struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private);
 	struct rte_eth_link link, old;
 	ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN;
+	struct ixgbe_interrupt *intr =
+		IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private);
 	int link_up;
 	int diag;
+	u32 speed = 0;
+	bool autoneg = false;
 
 	link.link_status = ETH_LINK_DOWN;
 	link.link_speed = 0;
@@ -3128,6 +3133,19 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
 
 	hw->mac.get_link_status = true;
 
+	if (intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) {
+		speed = hw->phy.autoneg_advertised;
+		if (!speed) {
+			ixgbe_get_link_capabilities(hw, &speed, &autoneg);
+			/* setup the highest link when no autoneg */
+			if (!autoneg) {
+				if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+					speed = IXGBE_LINK_SPEED_10GB_FULL;
+			}
+		}
+		ixgbe_setup_link(hw, speed, true);
+	}
+
 	/* check if it needs to wait to complete, if lsc interrupt is enabled */
 	if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0)
 		diag = ixgbe_check_link(hw, &link_speed, &link_up, 0);
@@ -3145,10 +3163,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete)
 
 	if (link_up == 0) {
 		rte_ixgbe_dev_atomic_write_link_status(dev, &link);
+		intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG;
 		if (link.link_status == old.link_status)
 			return -1;
 		return 0;
 	}
+	intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG;
 	link.link_status = ETH_LINK_UP;
 	link.link_duplex = ETH_LINK_FULL_DUPLEX;
 
diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
index e060c3d..9d335ba 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.h
+++ b/drivers/net/ixgbe/ixgbe_ethdev.h
@@ -43,6 +43,7 @@
 #define IXGBE_FLAG_NEED_LINK_UPDATE (uint32_t)(1 << 0)
 #define IXGBE_FLAG_MAILBOX          (uint32_t)(1 << 1)
 #define IXGBE_FLAG_PHY_INTERRUPT    (uint32_t)(1 << 2)
+#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 3)
 
 /*
  * Defines that were not part of ixgbe_type.h as they are not used by the
-- 
1.7.10.4