* [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: jun.nie, wim, linux, robh+dt, mark.rutland, mathieu.poirier
Cc: linux-arm-kernel, linux-watchdog, devicetree, linux-kernel,
shawnguo, baoyou.xie, xie.baoyou, chen.chaokai, wang.qiang01
This patch adds dt-binding documentation for zx2967 family
watchdog controller.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/watchdog/zte,zx2967-wdt.txt | 32 ++++++++++++++++++++++
1 file changed, 32 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
new file mode 100644
index 0000000..06ce677
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
@@ -0,0 +1,32 @@
+ZTE zx2967 Watchdog timer
+
+Required properties:
+
+- compatible : should be one of the following.
+ * zte,zx296718-wdt
+- reg : Specifies base physical address and size of the registers.
+- clocks : Pairs of phandle and specifier referencing the controller's clocks.
+- resets : Reference to the reset controller controlling the watchdog
+ controller.
+
+Optional properties:
+
+- timeout-sec : Contains the watchdog timeout in seconds.
+- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
+ if we don't want to restart system when watchdog been triggered,
+ it's not required, vice versa.
+ It should include following fields.
+ * phandle of aon-sysctrl.
+ * offset of register that be written, should be 0xb0.
+ * configure value that be written to aon-sysctrl.
+ * bit mask, corresponding bits will be affected.
+
+Example:
+
+wdt: watchdog@1465000 {
+ compatible = "zte,zx296718-wdt";
+ reg = <0x1465000 0x1000>;
+ clocks = <&topcrm WDT_WCLK>;
+ resets = <&toprst 35>;
+ zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: jun.nie-QSEj5FYQhm4dnm+yROfE0A, wim-IQzOog9fTRqzQB+pC5nmwQ,
linux-0h96xk9xTtrk1uMJSBkQmQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
baoyou.xie-QSEj5FYQhm4dnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
This patch adds dt-binding documentation for zx2967 family
watchdog controller.
Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
.../bindings/watchdog/zte,zx2967-wdt.txt | 32 ++++++++++++++++++++++
1 file changed, 32 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
new file mode 100644
index 0000000..06ce677
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
@@ -0,0 +1,32 @@
+ZTE zx2967 Watchdog timer
+
+Required properties:
+
+- compatible : should be one of the following.
+ * zte,zx296718-wdt
+- reg : Specifies base physical address and size of the registers.
+- clocks : Pairs of phandle and specifier referencing the controller's clocks.
+- resets : Reference to the reset controller controlling the watchdog
+ controller.
+
+Optional properties:
+
+- timeout-sec : Contains the watchdog timeout in seconds.
+- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
+ if we don't want to restart system when watchdog been triggered,
+ it's not required, vice versa.
+ It should include following fields.
+ * phandle of aon-sysctrl.
+ * offset of register that be written, should be 0xb0.
+ * configure value that be written to aon-sysctrl.
+ * bit mask, corresponding bits will be affected.
+
+Example:
+
+wdt: watchdog@1465000 {
+ compatible = "zte,zx296718-wdt";
+ reg = <0x1465000 0x1000>;
+ clocks = <&topcrm WDT_WCLK>;
+ resets = <&toprst 35>;
+ zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds dt-binding documentation for zx2967 family
watchdog controller.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/watchdog/zte,zx2967-wdt.txt | 32 ++++++++++++++++++++++
1 file changed, 32 insertions(+)
create mode 100644 Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
new file mode 100644
index 0000000..06ce677
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
@@ -0,0 +1,32 @@
+ZTE zx2967 Watchdog timer
+
+Required properties:
+
+- compatible : should be one of the following.
+ * zte,zx296718-wdt
+- reg : Specifies base physical address and size of the registers.
+- clocks : Pairs of phandle and specifier referencing the controller's clocks.
+- resets : Reference to the reset controller controlling the watchdog
+ controller.
+
+Optional properties:
+
+- timeout-sec : Contains the watchdog timeout in seconds.
+- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
+ if we don't want to restart system when watchdog been triggered,
+ it's not required, vice versa.
+ It should include following fields.
+ * phandle of aon-sysctrl.
+ * offset of register that be written, should be 0xb0.
+ * configure value that be written to aon-sysctrl.
+ * bit mask, corresponding bits will be affected.
+
+Example:
+
+wdt: watchdog at 1465000 {
+ compatible = "zte,zx296718-wdt";
+ reg = <0x1465000 0x1000>;
+ clocks = <&topcrm WDT_WCLK>;
+ resets = <&toprst 35>;
+ zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: jun.nie, wim, linux, robh+dt, mark.rutland, mathieu.poirier
Cc: linux-arm-kernel, linux-watchdog, devicetree, linux-kernel,
shawnguo, baoyou.xie, xie.baoyou, chen.chaokai, wang.qiang01
Add the zx2967 watchdog controller driver as maintained by ARM ZTE
architecture maintainers, as they're parts of the core IP.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
---
MAINTAINERS | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index edfdea3..275c434 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
F: drivers/reset/reset-zx2967.c
F: drivers/soc/zte/
F: drivers/thermal/zx*
+F: drivers/watchdog/zx2967_wdt.c
F: Documentation/devicetree/bindings/arm/zte.txt
F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
F: Documentation/devicetree/bindings/soc/zte/
F: Documentation/devicetree/bindings/thermal/zx*
+F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
F: include/dt-bindings/soc/zx*.h
ARM/ZYNQ ARCHITECTURE
--
2.7.4
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: jun.nie-QSEj5FYQhm4dnm+yROfE0A, wim-IQzOog9fTRqzQB+pC5nmwQ,
linux-0h96xk9xTtrk1uMJSBkQmQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
baoyou.xie-QSEj5FYQhm4dnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
Add the zx2967 watchdog controller driver as maintained by ARM ZTE
architecture maintainers, as they're parts of the core IP.
Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
MAINTAINERS | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index edfdea3..275c434 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
F: drivers/reset/reset-zx2967.c
F: drivers/soc/zte/
F: drivers/thermal/zx*
+F: drivers/watchdog/zx2967_wdt.c
F: Documentation/devicetree/bindings/arm/zte.txt
F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
F: Documentation/devicetree/bindings/soc/zte/
F: Documentation/devicetree/bindings/thermal/zx*
+F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
F: include/dt-bindings/soc/zx*.h
ARM/ZYNQ ARCHITECTURE
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: linux-arm-kernel
Add the zx2967 watchdog controller driver as maintained by ARM ZTE
architecture maintainers, as they're parts of the core IP.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
---
MAINTAINERS | 2 ++
1 file changed, 2 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index edfdea3..275c434 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
F: drivers/reset/reset-zx2967.c
F: drivers/soc/zte/
F: drivers/thermal/zx*
+F: drivers/watchdog/zx2967_wdt.c
F: Documentation/devicetree/bindings/arm/zte.txt
F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
F: Documentation/devicetree/bindings/soc/zte/
F: Documentation/devicetree/bindings/thermal/zx*
+F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
F: include/dt-bindings/soc/zx*.h
ARM/ZYNQ ARCHITECTURE
--
2.7.4
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
2017-02-04 1:34 ` Baoyou Xie
@ 2017-02-04 1:34 ` Baoyou Xie
-1 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: jun.nie, wim, linux, robh+dt, mark.rutland, mathieu.poirier
Cc: linux-arm-kernel, linux-watchdog, devicetree, linux-kernel,
shawnguo, baoyou.xie, xie.baoyou, chen.chaokai, wang.qiang01
This patch adds watchdog controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
---
drivers/watchdog/Kconfig | 10 ++
drivers/watchdog/Makefile | 1 +
drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 302 insertions(+)
create mode 100644 drivers/watchdog/zx2967_wdt.c
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index acb00b5..05093a2 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
To compile this driver as a module, choose M here: the
module will be called aspeed_wdt.
+config ZX2967_WATCHDOG
+ tristate "ZTE zx2967 SoCs watchdog support"
+ depends on ARCH_ZX
+ select WATCHDOG_CORE
+ help
+ Say Y here to include support for the watchdog timer
+ in ZTE zx2967 SoCs.
+ To compile this driver as a module, choose M here: the
+ module will be called zx2967_wdt.
+
# AVR32 Architecture
config AT32AP700X_WDT
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 0c3d35e..bf2d296 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
+obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
# AVR32 Architecture
obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
new file mode 100644
index 0000000..e290d5a
--- /dev/null
+++ b/drivers/watchdog/zx2967_wdt.c
@@ -0,0 +1,291 @@
+/*
+ * watchdog driver for ZTE's zx2967 family
+ *
+ * Copyright (C) 2017 ZTE Ltd.
+ *
+ * Author: Baoyou Xie <baoyou.xie@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/watchdog.h>
+
+#define ZX2967_WDT_CFG_REG 0x4
+#define ZX2967_WDT_LOAD_REG 0x8
+#define ZX2967_WDT_REFRESH_REG 0x18
+#define ZX2967_WDT_START_REG 0x1c
+
+#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
+
+#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
+#define ZX2967_WDT_START_EN 0x1
+
+/*
+ * Hardware magic number.
+ * When watchdog reg is written, the lowest 16 bits are valid, but
+ * the highest 16 bits should be always this number.
+ */
+#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
+#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
+
+#define ZX2967_WDT_DIV_DEFAULT 16
+#define ZX2967_WDT_DEFAULT_TIMEOUT 32
+#define ZX2967_WDT_MIN_TIMEOUT 1
+#define ZX2967_WDT_MAX_TIMEOUT 524
+#define ZX2967_WDT_MAX_COUNT 0xffff
+
+#define ZX2967_WDT_CLK_FREQ 0x8000
+
+#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
+
+struct zx2967_wdt {
+ struct watchdog_device wdt_device;
+ void __iomem *reg_base;
+ struct clk *clock;
+};
+
+static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
+{
+ return readl_relaxed(wdt->reg_base + reg);
+}
+
+static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
+{
+ writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
+}
+
+static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
+{
+ u32 val;
+
+ val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
+ /*
+ * Bit 4-5, 1 and 2: refresh config info
+ * Bit 2-3, 1 and 2: refresh counter
+ * Bit 0-1, 1 and 2: refresh int-value
+ * we shift each group value between 1 and 2 to refresh all data.
+ */
+ val ^= ZX2967_WDT_REFRESH_MASK;
+ zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
+ val & ZX2967_WDT_VAL_MASK);
+}
+
+static int
+zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+ unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
+ u32 count;
+
+ count = timeout * ZX2967_WDT_CLK_FREQ;
+ if (count > divisor * ZX2967_WDT_MAX_COUNT)
+ divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
+ count = DIV_ROUND_UP(count, divisor);
+ zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
+ ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
+ zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
+ count & ZX2967_WDT_VAL_MASK);
+ zx2967_wdt_refresh(wdt);
+ wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
+
+ return 0;
+}
+
+static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
+{
+ u32 val;
+
+ val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
+ val |= ZX2967_WDT_START_EN;
+ zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
+ val & ZX2967_WDT_VAL_MASK);
+}
+
+static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
+{
+ u32 val;
+
+ val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
+ val &= ~ZX2967_WDT_START_EN;
+ zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
+ val & ZX2967_WDT_VAL_MASK);
+}
+
+static int zx2967_wdt_start(struct watchdog_device *wdd)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+
+ zx2967_wdt_set_timeout(wdd, wdd->timeout);
+ __zx2967_wdt_start(wdt);
+
+ return 0;
+}
+
+static int zx2967_wdt_stop(struct watchdog_device *wdd)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+
+ __zx2967_wdt_stop(wdt);
+
+ return 0;
+}
+
+static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+
+ zx2967_wdt_refresh(wdt);
+
+ return 0;
+}
+
+#define ZX2967_WDT_OPTIONS \
+ (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
+static const struct watchdog_info zx2967_wdt_ident = {
+ .options = ZX2967_WDT_OPTIONS,
+ .identity = "zx2967 watchdog",
+};
+
+static struct watchdog_ops zx2967_wdt_ops = {
+ .owner = THIS_MODULE,
+ .start = zx2967_wdt_start,
+ .stop = zx2967_wdt_stop,
+ .ping = zx2967_wdt_keepalive,
+ .set_timeout = zx2967_wdt_set_timeout,
+};
+
+static void zx2967_wdt_reset_sysctrl(struct device *dev)
+{
+ int ret;
+ void __iomem *regmap;
+ unsigned int offset, mask, config;
+ struct of_phandle_args out_args;
+
+ ret = of_parse_phandle_with_fixed_args(dev->of_node,
+ "zte,wdt-reset-sysctrl", 3, 0, &out_args);
+ if (ret)
+ return;
+
+ offset = out_args.args[0];
+ config = out_args.args[1];
+ mask = out_args.args[2];
+
+ regmap = syscon_node_to_regmap(out_args.np);
+ if (IS_ERR(regmap)) {
+ of_node_put(out_args.np);
+ return;
+ }
+
+ regmap_update_bits(regmap, offset, mask, config);
+ of_node_put(out_args.np);
+}
+
+static int zx2967_wdt_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct zx2967_wdt *wdt;
+ struct resource *base;
+ int ret;
+ struct reset_control *rstc;
+
+ wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
+ if (!wdt)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, wdt);
+
+ wdt->wdt_device.info = &zx2967_wdt_ident;
+ wdt->wdt_device.ops = &zx2967_wdt_ops;
+ wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
+ wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
+ wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
+ wdt->wdt_device.parent = &pdev->dev;
+
+ base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ wdt->reg_base = devm_ioremap_resource(dev, base);
+ if (IS_ERR(wdt->reg_base)) {
+ dev_err(dev, "ioremap failed\n");
+ return PTR_ERR(wdt->reg_base);
+ }
+
+ zx2967_wdt_reset_sysctrl(dev);
+
+ wdt->clock = devm_clk_get(dev, NULL);
+ if (IS_ERR(wdt->clock)) {
+ dev_err(dev, "failed to find watchdog clock source\n");
+ return PTR_ERR(wdt->clock);
+ }
+
+ ret = clk_prepare_enable(wdt->clock);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable clock\n");
+ return ret;
+ }
+ clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
+
+ rstc = devm_reset_control_get(dev, NULL);
+ if (IS_ERR(rstc)) {
+ dev_err(dev, "failed to get rstc");
+ ret = PTR_ERR(rstc);
+ goto err;
+ }
+
+ reset_control_assert(rstc);
+ reset_control_deassert(rstc);
+
+ watchdog_set_drvdata(&wdt->wdt_device, wdt);
+ watchdog_init_timeout(&wdt->wdt_device,
+ ZX2967_WDT_DEFAULT_TIMEOUT, dev);
+ watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
+
+ ret = watchdog_register_device(&wdt->wdt_device);
+ if (ret)
+ goto err;
+
+ dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
+ wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
+
+ return 0;
+
+err:
+ clk_disable_unprepare(wdt->clock);
+ return ret;
+}
+
+static int zx2967_wdt_remove(struct platform_device *pdev)
+{
+ struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
+
+ watchdog_unregister_device(&wdt->wdt_device);
+ clk_disable_unprepare(wdt->clock);
+
+ return 0;
+}
+
+static const struct of_device_id zx2967_wdt_match[] = {
+ { .compatible = "zte,zx296718-wdt", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
+
+static struct platform_driver zx2967_wdt_driver = {
+ .probe = zx2967_wdt_probe,
+ .remove = zx2967_wdt_remove,
+ .driver = {
+ .name = "zx2967-wdt",
+ .of_match_table = of_match_ptr(zx2967_wdt_match),
+ },
+};
+module_platform_driver(zx2967_wdt_driver);
+
+MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
+MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related [flat|nested] 30+ messages in thread
* [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-04 1:34 ` Baoyou Xie
0 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-04 1:34 UTC (permalink / raw)
To: linux-arm-kernel
This patch adds watchdog controller driver for ZTE's zx2967 family.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
---
drivers/watchdog/Kconfig | 10 ++
drivers/watchdog/Makefile | 1 +
drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 302 insertions(+)
create mode 100644 drivers/watchdog/zx2967_wdt.c
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index acb00b5..05093a2 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
To compile this driver as a module, choose M here: the
module will be called aspeed_wdt.
+config ZX2967_WATCHDOG
+ tristate "ZTE zx2967 SoCs watchdog support"
+ depends on ARCH_ZX
+ select WATCHDOG_CORE
+ help
+ Say Y here to include support for the watchdog timer
+ in ZTE zx2967 SoCs.
+ To compile this driver as a module, choose M here: the
+ module will be called zx2967_wdt.
+
# AVR32 Architecture
config AT32AP700X_WDT
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 0c3d35e..bf2d296 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
+obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
# AVR32 Architecture
obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
new file mode 100644
index 0000000..e290d5a
--- /dev/null
+++ b/drivers/watchdog/zx2967_wdt.c
@@ -0,0 +1,291 @@
+/*
+ * watchdog driver for ZTE's zx2967 family
+ *
+ * Copyright (C) 2017 ZTE Ltd.
+ *
+ * Author: Baoyou Xie <baoyou.xie@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/watchdog.h>
+
+#define ZX2967_WDT_CFG_REG 0x4
+#define ZX2967_WDT_LOAD_REG 0x8
+#define ZX2967_WDT_REFRESH_REG 0x18
+#define ZX2967_WDT_START_REG 0x1c
+
+#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
+
+#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
+#define ZX2967_WDT_START_EN 0x1
+
+/*
+ * Hardware magic number.
+ * When watchdog reg is written, the lowest 16 bits are valid, but
+ * the highest 16 bits should be always this number.
+ */
+#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
+#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
+
+#define ZX2967_WDT_DIV_DEFAULT 16
+#define ZX2967_WDT_DEFAULT_TIMEOUT 32
+#define ZX2967_WDT_MIN_TIMEOUT 1
+#define ZX2967_WDT_MAX_TIMEOUT 524
+#define ZX2967_WDT_MAX_COUNT 0xffff
+
+#define ZX2967_WDT_CLK_FREQ 0x8000
+
+#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
+
+struct zx2967_wdt {
+ struct watchdog_device wdt_device;
+ void __iomem *reg_base;
+ struct clk *clock;
+};
+
+static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
+{
+ return readl_relaxed(wdt->reg_base + reg);
+}
+
+static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
+{
+ writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
+}
+
+static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
+{
+ u32 val;
+
+ val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
+ /*
+ * Bit 4-5, 1 and 2: refresh config info
+ * Bit 2-3, 1 and 2: refresh counter
+ * Bit 0-1, 1 and 2: refresh int-value
+ * we shift each group value between 1 and 2 to refresh all data.
+ */
+ val ^= ZX2967_WDT_REFRESH_MASK;
+ zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
+ val & ZX2967_WDT_VAL_MASK);
+}
+
+static int
+zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+ unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
+ u32 count;
+
+ count = timeout * ZX2967_WDT_CLK_FREQ;
+ if (count > divisor * ZX2967_WDT_MAX_COUNT)
+ divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
+ count = DIV_ROUND_UP(count, divisor);
+ zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
+ ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
+ zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
+ count & ZX2967_WDT_VAL_MASK);
+ zx2967_wdt_refresh(wdt);
+ wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
+
+ return 0;
+}
+
+static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
+{
+ u32 val;
+
+ val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
+ val |= ZX2967_WDT_START_EN;
+ zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
+ val & ZX2967_WDT_VAL_MASK);
+}
+
+static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
+{
+ u32 val;
+
+ val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
+ val &= ~ZX2967_WDT_START_EN;
+ zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
+ val & ZX2967_WDT_VAL_MASK);
+}
+
+static int zx2967_wdt_start(struct watchdog_device *wdd)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+
+ zx2967_wdt_set_timeout(wdd, wdd->timeout);
+ __zx2967_wdt_start(wdt);
+
+ return 0;
+}
+
+static int zx2967_wdt_stop(struct watchdog_device *wdd)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+
+ __zx2967_wdt_stop(wdt);
+
+ return 0;
+}
+
+static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
+{
+ struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
+
+ zx2967_wdt_refresh(wdt);
+
+ return 0;
+}
+
+#define ZX2967_WDT_OPTIONS \
+ (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
+static const struct watchdog_info zx2967_wdt_ident = {
+ .options = ZX2967_WDT_OPTIONS,
+ .identity = "zx2967 watchdog",
+};
+
+static struct watchdog_ops zx2967_wdt_ops = {
+ .owner = THIS_MODULE,
+ .start = zx2967_wdt_start,
+ .stop = zx2967_wdt_stop,
+ .ping = zx2967_wdt_keepalive,
+ .set_timeout = zx2967_wdt_set_timeout,
+};
+
+static void zx2967_wdt_reset_sysctrl(struct device *dev)
+{
+ int ret;
+ void __iomem *regmap;
+ unsigned int offset, mask, config;
+ struct of_phandle_args out_args;
+
+ ret = of_parse_phandle_with_fixed_args(dev->of_node,
+ "zte,wdt-reset-sysctrl", 3, 0, &out_args);
+ if (ret)
+ return;
+
+ offset = out_args.args[0];
+ config = out_args.args[1];
+ mask = out_args.args[2];
+
+ regmap = syscon_node_to_regmap(out_args.np);
+ if (IS_ERR(regmap)) {
+ of_node_put(out_args.np);
+ return;
+ }
+
+ regmap_update_bits(regmap, offset, mask, config);
+ of_node_put(out_args.np);
+}
+
+static int zx2967_wdt_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct zx2967_wdt *wdt;
+ struct resource *base;
+ int ret;
+ struct reset_control *rstc;
+
+ wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
+ if (!wdt)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, wdt);
+
+ wdt->wdt_device.info = &zx2967_wdt_ident;
+ wdt->wdt_device.ops = &zx2967_wdt_ops;
+ wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
+ wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
+ wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
+ wdt->wdt_device.parent = &pdev->dev;
+
+ base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ wdt->reg_base = devm_ioremap_resource(dev, base);
+ if (IS_ERR(wdt->reg_base)) {
+ dev_err(dev, "ioremap failed\n");
+ return PTR_ERR(wdt->reg_base);
+ }
+
+ zx2967_wdt_reset_sysctrl(dev);
+
+ wdt->clock = devm_clk_get(dev, NULL);
+ if (IS_ERR(wdt->clock)) {
+ dev_err(dev, "failed to find watchdog clock source\n");
+ return PTR_ERR(wdt->clock);
+ }
+
+ ret = clk_prepare_enable(wdt->clock);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable clock\n");
+ return ret;
+ }
+ clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
+
+ rstc = devm_reset_control_get(dev, NULL);
+ if (IS_ERR(rstc)) {
+ dev_err(dev, "failed to get rstc");
+ ret = PTR_ERR(rstc);
+ goto err;
+ }
+
+ reset_control_assert(rstc);
+ reset_control_deassert(rstc);
+
+ watchdog_set_drvdata(&wdt->wdt_device, wdt);
+ watchdog_init_timeout(&wdt->wdt_device,
+ ZX2967_WDT_DEFAULT_TIMEOUT, dev);
+ watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
+
+ ret = watchdog_register_device(&wdt->wdt_device);
+ if (ret)
+ goto err;
+
+ dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
+ wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
+
+ return 0;
+
+err:
+ clk_disable_unprepare(wdt->clock);
+ return ret;
+}
+
+static int zx2967_wdt_remove(struct platform_device *pdev)
+{
+ struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
+
+ watchdog_unregister_device(&wdt->wdt_device);
+ clk_disable_unprepare(wdt->clock);
+
+ return 0;
+}
+
+static const struct of_device_id zx2967_wdt_match[] = {
+ { .compatible = "zte,zx296718-wdt", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
+
+static struct platform_driver zx2967_wdt_driver = {
+ .probe = zx2967_wdt_probe,
+ .remove = zx2967_wdt_remove,
+ .driver = {
+ .name = "zx2967-wdt",
+ .of_match_table = of_match_ptr(zx2967_wdt_match),
+ },
+};
+module_platform_driver(zx2967_wdt_driver);
+
+MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
+MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related [flat|nested] 30+ messages in thread
* Re: [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller
@ 2017-02-05 0:04 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:04 UTC (permalink / raw)
To: Baoyou Xie, jun.nie, wim, robh+dt, mark.rutland, mathieu.poirier
Cc: linux-arm-kernel, linux-watchdog, devicetree, linux-kernel,
shawnguo, xie.baoyou, chen.chaokai, wang.qiang01
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> This patch adds dt-binding documentation for zx2967 family
> watchdog controller.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> .../bindings/watchdog/zte,zx2967-wdt.txt | 32 ++++++++++++++++++++++
> 1 file changed, 32 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
>
> diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> new file mode 100644
> index 0000000..06ce677
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> @@ -0,0 +1,32 @@
> +ZTE zx2967 Watchdog timer
> +
> +Required properties:
> +
> +- compatible : should be one of the following.
> + * zte,zx296718-wdt
> +- reg : Specifies base physical address and size of the registers.
> +- clocks : Pairs of phandle and specifier referencing the controller's clocks.
> +- resets : Reference to the reset controller controlling the watchdog
> + controller.
> +
> +Optional properties:
> +
> +- timeout-sec : Contains the watchdog timeout in seconds.
> +- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
> + if we don't want to restart system when watchdog been triggered,
> + it's not required, vice versa.
> + It should include following fields.
> + * phandle of aon-sysctrl.
> + * offset of register that be written, should be 0xb0.
> + * configure value that be written to aon-sysctrl.
> + * bit mask, corresponding bits will be affected.
> +
> +Example:
> +
> +wdt: watchdog@1465000 {
> + compatible = "zte,zx296718-wdt";
> + reg = <0x1465000 0x1000>;
> + clocks = <&topcrm WDT_WCLK>;
> + resets = <&toprst 35>;
> + zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
> +};
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller
@ 2017-02-05 0:04 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:04 UTC (permalink / raw)
To: Baoyou Xie, jun.nie-QSEj5FYQhm4dnm+yROfE0A,
wim-IQzOog9fTRqzQB+pC5nmwQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> This patch adds dt-binding documentation for zx2967 family
> watchdog controller.
>
> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Reviewed-by: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
> ---
> .../bindings/watchdog/zte,zx2967-wdt.txt | 32 ++++++++++++++++++++++
> 1 file changed, 32 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
>
> diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> new file mode 100644
> index 0000000..06ce677
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> @@ -0,0 +1,32 @@
> +ZTE zx2967 Watchdog timer
> +
> +Required properties:
> +
> +- compatible : should be one of the following.
> + * zte,zx296718-wdt
> +- reg : Specifies base physical address and size of the registers.
> +- clocks : Pairs of phandle and specifier referencing the controller's clocks.
> +- resets : Reference to the reset controller controlling the watchdog
> + controller.
> +
> +Optional properties:
> +
> +- timeout-sec : Contains the watchdog timeout in seconds.
> +- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
> + if we don't want to restart system when watchdog been triggered,
> + it's not required, vice versa.
> + It should include following fields.
> + * phandle of aon-sysctrl.
> + * offset of register that be written, should be 0xb0.
> + * configure value that be written to aon-sysctrl.
> + * bit mask, corresponding bits will be affected.
> +
> +Example:
> +
> +wdt: watchdog@1465000 {
> + compatible = "zte,zx296718-wdt";
> + reg = <0x1465000 0x1000>;
> + clocks = <&topcrm WDT_WCLK>;
> + resets = <&toprst 35>;
> + zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
> +};
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller
@ 2017-02-05 0:04 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:04 UTC (permalink / raw)
To: linux-arm-kernel
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> This patch adds dt-binding documentation for zx2967 family
> watchdog controller.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> .../bindings/watchdog/zte,zx2967-wdt.txt | 32 ++++++++++++++++++++++
> 1 file changed, 32 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
>
> diff --git a/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> new file mode 100644
> index 0000000..06ce677
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> @@ -0,0 +1,32 @@
> +ZTE zx2967 Watchdog timer
> +
> +Required properties:
> +
> +- compatible : should be one of the following.
> + * zte,zx296718-wdt
> +- reg : Specifies base physical address and size of the registers.
> +- clocks : Pairs of phandle and specifier referencing the controller's clocks.
> +- resets : Reference to the reset controller controlling the watchdog
> + controller.
> +
> +Optional properties:
> +
> +- timeout-sec : Contains the watchdog timeout in seconds.
> +- zte,wdt-reset-sysctrl : Directs how to reset system by the watchdog.
> + if we don't want to restart system when watchdog been triggered,
> + it's not required, vice versa.
> + It should include following fields.
> + * phandle of aon-sysctrl.
> + * offset of register that be written, should be 0xb0.
> + * configure value that be written to aon-sysctrl.
> + * bit mask, corresponding bits will be affected.
> +
> +Example:
> +
> +wdt: watchdog at 1465000 {
> + compatible = "zte,zx296718-wdt";
> + reg = <0x1465000 0x1000>;
> + clocks = <&topcrm WDT_WCLK>;
> + resets = <&toprst 35>;
> + zte,wdt-reset-sysctrl = <&aon_sysctrl 0xb0 1 0x115>;
> +};
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 0:05 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:05 UTC (permalink / raw)
To: Baoyou Xie, jun.nie, wim, robh+dt, mark.rutland, mathieu.poirier
Cc: linux-arm-kernel, linux-watchdog, devicetree, linux-kernel,
shawnguo, xie.baoyou, chen.chaokai, wang.qiang01
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
> architecture maintainers, as they're parts of the core IP.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
I assume you'll submit this patch through the arm tree ?
Guenter
> ---
> MAINTAINERS | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index edfdea3..275c434 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
> F: drivers/reset/reset-zx2967.c
> F: drivers/soc/zte/
> F: drivers/thermal/zx*
> +F: drivers/watchdog/zx2967_wdt.c
> F: Documentation/devicetree/bindings/arm/zte.txt
> F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
> F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
> F: Documentation/devicetree/bindings/soc/zte/
> F: Documentation/devicetree/bindings/thermal/zx*
> +F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> F: include/dt-bindings/soc/zx*.h
>
> ARM/ZYNQ ARCHITECTURE
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 0:05 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:05 UTC (permalink / raw)
To: Baoyou Xie, jun.nie-QSEj5FYQhm4dnm+yROfE0A,
wim-IQzOog9fTRqzQB+pC5nmwQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
> architecture maintainers, as they're parts of the core IP.
>
> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Reviewed-by: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
I assume you'll submit this patch through the arm tree ?
Guenter
> ---
> MAINTAINERS | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index edfdea3..275c434 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
> F: drivers/reset/reset-zx2967.c
> F: drivers/soc/zte/
> F: drivers/thermal/zx*
> +F: drivers/watchdog/zx2967_wdt.c
> F: Documentation/devicetree/bindings/arm/zte.txt
> F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
> F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
> F: Documentation/devicetree/bindings/soc/zte/
> F: Documentation/devicetree/bindings/thermal/zx*
> +F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> F: include/dt-bindings/soc/zx*.h
>
> ARM/ZYNQ ARCHITECTURE
>
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 0:05 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:05 UTC (permalink / raw)
To: linux-arm-kernel
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
> architecture maintainers, as they're parts of the core IP.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
I assume you'll submit this patch through the arm tree ?
Guenter
> ---
> MAINTAINERS | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index edfdea3..275c434 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
> F: drivers/reset/reset-zx2967.c
> F: drivers/soc/zte/
> F: drivers/thermal/zx*
> +F: drivers/watchdog/zx2967_wdt.c
> F: Documentation/devicetree/bindings/arm/zte.txt
> F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
> F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
> F: Documentation/devicetree/bindings/soc/zte/
> F: Documentation/devicetree/bindings/thermal/zx*
> +F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
> F: include/dt-bindings/soc/zx*.h
>
> ARM/ZYNQ ARCHITECTURE
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-05 0:06 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:06 UTC (permalink / raw)
To: Baoyou Xie, jun.nie, wim, robh+dt, mark.rutland, mathieu.poirier
Cc: linux-arm-kernel, linux-watchdog, devicetree, linux-kernel,
shawnguo, xie.baoyou, chen.chaokai, wang.qiang01
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> This patch adds watchdog controller driver for ZTE's zx2967 family.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> drivers/watchdog/Kconfig | 10 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 302 insertions(+)
> create mode 100644 drivers/watchdog/zx2967_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index acb00b5..05093a2 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
> To compile this driver as a module, choose M here: the
> module will be called aspeed_wdt.
>
> +config ZX2967_WATCHDOG
> + tristate "ZTE zx2967 SoCs watchdog support"
> + depends on ARCH_ZX
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support for the watchdog timer
> + in ZTE zx2967 SoCs.
> + To compile this driver as a module, choose M here: the
> + module will be called zx2967_wdt.
> +
> # AVR32 Architecture
>
> config AT32AP700X_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 0c3d35e..bf2d296 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
> obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
> obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
> obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
> +obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
>
> # AVR32 Architecture
> obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
> diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
> new file mode 100644
> index 0000000..e290d5a
> --- /dev/null
> +++ b/drivers/watchdog/zx2967_wdt.c
> @@ -0,0 +1,291 @@
> +/*
> + * watchdog driver for ZTE's zx2967 family
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/watchdog.h>
> +
> +#define ZX2967_WDT_CFG_REG 0x4
> +#define ZX2967_WDT_LOAD_REG 0x8
> +#define ZX2967_WDT_REFRESH_REG 0x18
> +#define ZX2967_WDT_START_REG 0x1c
> +
> +#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
> +
> +#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
> +#define ZX2967_WDT_START_EN 0x1
> +
> +/*
> + * Hardware magic number.
> + * When watchdog reg is written, the lowest 16 bits are valid, but
> + * the highest 16 bits should be always this number.
> + */
> +#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
> +#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
> +
> +#define ZX2967_WDT_DIV_DEFAULT 16
> +#define ZX2967_WDT_DEFAULT_TIMEOUT 32
> +#define ZX2967_WDT_MIN_TIMEOUT 1
> +#define ZX2967_WDT_MAX_TIMEOUT 524
> +#define ZX2967_WDT_MAX_COUNT 0xffff
> +
> +#define ZX2967_WDT_CLK_FREQ 0x8000
> +
> +#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
> +
> +struct zx2967_wdt {
> + struct watchdog_device wdt_device;
> + void __iomem *reg_base;
> + struct clk *clock;
> +};
> +
> +static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
> +{
> + return readl_relaxed(wdt->reg_base + reg);
> +}
> +
> +static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
> +{
> + writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
> +}
> +
> +static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
> + /*
> + * Bit 4-5, 1 and 2: refresh config info
> + * Bit 2-3, 1 and 2: refresh counter
> + * Bit 0-1, 1 and 2: refresh int-value
> + * we shift each group value between 1 and 2 to refresh all data.
> + */
> + val ^= ZX2967_WDT_REFRESH_MASK;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int
> +zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> + unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
> + u32 count;
> +
> + count = timeout * ZX2967_WDT_CLK_FREQ;
> + if (count > divisor * ZX2967_WDT_MAX_COUNT)
> + divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
> + count = DIV_ROUND_UP(count, divisor);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
> + ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
> + count & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_refresh(wdt);
> + wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
> +
> + return 0;
> +}
> +
> +static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val |= ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val &= ~ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int zx2967_wdt_start(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_set_timeout(wdd, wdd->timeout);
> + __zx2967_wdt_start(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_stop(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + __zx2967_wdt_stop(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_refresh(wdt);
> +
> + return 0;
> +}
> +
> +#define ZX2967_WDT_OPTIONS \
> + (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
> +static const struct watchdog_info zx2967_wdt_ident = {
> + .options = ZX2967_WDT_OPTIONS,
> + .identity = "zx2967 watchdog",
> +};
> +
> +static struct watchdog_ops zx2967_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = zx2967_wdt_start,
> + .stop = zx2967_wdt_stop,
> + .ping = zx2967_wdt_keepalive,
> + .set_timeout = zx2967_wdt_set_timeout,
> +};
> +
> +static void zx2967_wdt_reset_sysctrl(struct device *dev)
> +{
> + int ret;
> + void __iomem *regmap;
> + unsigned int offset, mask, config;
> + struct of_phandle_args out_args;
> +
> + ret = of_parse_phandle_with_fixed_args(dev->of_node,
> + "zte,wdt-reset-sysctrl", 3, 0, &out_args);
> + if (ret)
> + return;
> +
> + offset = out_args.args[0];
> + config = out_args.args[1];
> + mask = out_args.args[2];
> +
> + regmap = syscon_node_to_regmap(out_args.np);
> + if (IS_ERR(regmap)) {
> + of_node_put(out_args.np);
> + return;
> + }
> +
> + regmap_update_bits(regmap, offset, mask, config);
> + of_node_put(out_args.np);
> +}
> +
> +static int zx2967_wdt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct zx2967_wdt *wdt;
> + struct resource *base;
> + int ret;
> + struct reset_control *rstc;
> +
> + wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, wdt);
> +
> + wdt->wdt_device.info = &zx2967_wdt_ident;
> + wdt->wdt_device.ops = &zx2967_wdt_ops;
> + wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
> + wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
> + wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
> + wdt->wdt_device.parent = &pdev->dev;
> +
> + base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + wdt->reg_base = devm_ioremap_resource(dev, base);
> + if (IS_ERR(wdt->reg_base)) {
> + dev_err(dev, "ioremap failed\n");
> + return PTR_ERR(wdt->reg_base);
> + }
> +
> + zx2967_wdt_reset_sysctrl(dev);
> +
> + wdt->clock = devm_clk_get(dev, NULL);
> + if (IS_ERR(wdt->clock)) {
> + dev_err(dev, "failed to find watchdog clock source\n");
> + return PTR_ERR(wdt->clock);
> + }
> +
> + ret = clk_prepare_enable(wdt->clock);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable clock\n");
> + return ret;
> + }
> + clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
> +
> + rstc = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(rstc)) {
> + dev_err(dev, "failed to get rstc");
> + ret = PTR_ERR(rstc);
> + goto err;
> + }
> +
> + reset_control_assert(rstc);
> + reset_control_deassert(rstc);
> +
> + watchdog_set_drvdata(&wdt->wdt_device, wdt);
> + watchdog_init_timeout(&wdt->wdt_device,
> + ZX2967_WDT_DEFAULT_TIMEOUT, dev);
> + watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
> +
> + ret = watchdog_register_device(&wdt->wdt_device);
> + if (ret)
> + goto err;
> +
> + dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
> + wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
> +
> + return 0;
> +
> +err:
> + clk_disable_unprepare(wdt->clock);
> + return ret;
> +}
> +
> +static int zx2967_wdt_remove(struct platform_device *pdev)
> +{
> + struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
> +
> + watchdog_unregister_device(&wdt->wdt_device);
> + clk_disable_unprepare(wdt->clock);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_wdt_match[] = {
> + { .compatible = "zte,zx296718-wdt", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
> +
> +static struct platform_driver zx2967_wdt_driver = {
> + .probe = zx2967_wdt_probe,
> + .remove = zx2967_wdt_remove,
> + .driver = {
> + .name = "zx2967-wdt",
> + .of_match_table = of_match_ptr(zx2967_wdt_match),
> + },
> +};
> +module_platform_driver(zx2967_wdt_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
> +MODULE_LICENSE("GPL v2");
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-05 0:06 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:06 UTC (permalink / raw)
To: Baoyou Xie, jun.nie-QSEj5FYQhm4dnm+yROfE0A,
wim-IQzOog9fTRqzQB+pC5nmwQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> This patch adds watchdog controller driver for ZTE's zx2967 family.
>
> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Reviewed-by: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
> ---
> drivers/watchdog/Kconfig | 10 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 302 insertions(+)
> create mode 100644 drivers/watchdog/zx2967_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index acb00b5..05093a2 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
> To compile this driver as a module, choose M here: the
> module will be called aspeed_wdt.
>
> +config ZX2967_WATCHDOG
> + tristate "ZTE zx2967 SoCs watchdog support"
> + depends on ARCH_ZX
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support for the watchdog timer
> + in ZTE zx2967 SoCs.
> + To compile this driver as a module, choose M here: the
> + module will be called zx2967_wdt.
> +
> # AVR32 Architecture
>
> config AT32AP700X_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 0c3d35e..bf2d296 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
> obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
> obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
> obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
> +obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
>
> # AVR32 Architecture
> obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
> diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
> new file mode 100644
> index 0000000..e290d5a
> --- /dev/null
> +++ b/drivers/watchdog/zx2967_wdt.c
> @@ -0,0 +1,291 @@
> +/*
> + * watchdog driver for ZTE's zx2967 family
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/watchdog.h>
> +
> +#define ZX2967_WDT_CFG_REG 0x4
> +#define ZX2967_WDT_LOAD_REG 0x8
> +#define ZX2967_WDT_REFRESH_REG 0x18
> +#define ZX2967_WDT_START_REG 0x1c
> +
> +#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
> +
> +#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
> +#define ZX2967_WDT_START_EN 0x1
> +
> +/*
> + * Hardware magic number.
> + * When watchdog reg is written, the lowest 16 bits are valid, but
> + * the highest 16 bits should be always this number.
> + */
> +#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
> +#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
> +
> +#define ZX2967_WDT_DIV_DEFAULT 16
> +#define ZX2967_WDT_DEFAULT_TIMEOUT 32
> +#define ZX2967_WDT_MIN_TIMEOUT 1
> +#define ZX2967_WDT_MAX_TIMEOUT 524
> +#define ZX2967_WDT_MAX_COUNT 0xffff
> +
> +#define ZX2967_WDT_CLK_FREQ 0x8000
> +
> +#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
> +
> +struct zx2967_wdt {
> + struct watchdog_device wdt_device;
> + void __iomem *reg_base;
> + struct clk *clock;
> +};
> +
> +static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
> +{
> + return readl_relaxed(wdt->reg_base + reg);
> +}
> +
> +static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
> +{
> + writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
> +}
> +
> +static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
> + /*
> + * Bit 4-5, 1 and 2: refresh config info
> + * Bit 2-3, 1 and 2: refresh counter
> + * Bit 0-1, 1 and 2: refresh int-value
> + * we shift each group value between 1 and 2 to refresh all data.
> + */
> + val ^= ZX2967_WDT_REFRESH_MASK;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int
> +zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> + unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
> + u32 count;
> +
> + count = timeout * ZX2967_WDT_CLK_FREQ;
> + if (count > divisor * ZX2967_WDT_MAX_COUNT)
> + divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
> + count = DIV_ROUND_UP(count, divisor);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
> + ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
> + count & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_refresh(wdt);
> + wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
> +
> + return 0;
> +}
> +
> +static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val |= ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val &= ~ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int zx2967_wdt_start(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_set_timeout(wdd, wdd->timeout);
> + __zx2967_wdt_start(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_stop(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + __zx2967_wdt_stop(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_refresh(wdt);
> +
> + return 0;
> +}
> +
> +#define ZX2967_WDT_OPTIONS \
> + (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
> +static const struct watchdog_info zx2967_wdt_ident = {
> + .options = ZX2967_WDT_OPTIONS,
> + .identity = "zx2967 watchdog",
> +};
> +
> +static struct watchdog_ops zx2967_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = zx2967_wdt_start,
> + .stop = zx2967_wdt_stop,
> + .ping = zx2967_wdt_keepalive,
> + .set_timeout = zx2967_wdt_set_timeout,
> +};
> +
> +static void zx2967_wdt_reset_sysctrl(struct device *dev)
> +{
> + int ret;
> + void __iomem *regmap;
> + unsigned int offset, mask, config;
> + struct of_phandle_args out_args;
> +
> + ret = of_parse_phandle_with_fixed_args(dev->of_node,
> + "zte,wdt-reset-sysctrl", 3, 0, &out_args);
> + if (ret)
> + return;
> +
> + offset = out_args.args[0];
> + config = out_args.args[1];
> + mask = out_args.args[2];
> +
> + regmap = syscon_node_to_regmap(out_args.np);
> + if (IS_ERR(regmap)) {
> + of_node_put(out_args.np);
> + return;
> + }
> +
> + regmap_update_bits(regmap, offset, mask, config);
> + of_node_put(out_args.np);
> +}
> +
> +static int zx2967_wdt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct zx2967_wdt *wdt;
> + struct resource *base;
> + int ret;
> + struct reset_control *rstc;
> +
> + wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, wdt);
> +
> + wdt->wdt_device.info = &zx2967_wdt_ident;
> + wdt->wdt_device.ops = &zx2967_wdt_ops;
> + wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
> + wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
> + wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
> + wdt->wdt_device.parent = &pdev->dev;
> +
> + base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + wdt->reg_base = devm_ioremap_resource(dev, base);
> + if (IS_ERR(wdt->reg_base)) {
> + dev_err(dev, "ioremap failed\n");
> + return PTR_ERR(wdt->reg_base);
> + }
> +
> + zx2967_wdt_reset_sysctrl(dev);
> +
> + wdt->clock = devm_clk_get(dev, NULL);
> + if (IS_ERR(wdt->clock)) {
> + dev_err(dev, "failed to find watchdog clock source\n");
> + return PTR_ERR(wdt->clock);
> + }
> +
> + ret = clk_prepare_enable(wdt->clock);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable clock\n");
> + return ret;
> + }
> + clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
> +
> + rstc = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(rstc)) {
> + dev_err(dev, "failed to get rstc");
> + ret = PTR_ERR(rstc);
> + goto err;
> + }
> +
> + reset_control_assert(rstc);
> + reset_control_deassert(rstc);
> +
> + watchdog_set_drvdata(&wdt->wdt_device, wdt);
> + watchdog_init_timeout(&wdt->wdt_device,
> + ZX2967_WDT_DEFAULT_TIMEOUT, dev);
> + watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
> +
> + ret = watchdog_register_device(&wdt->wdt_device);
> + if (ret)
> + goto err;
> +
> + dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
> + wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
> +
> + return 0;
> +
> +err:
> + clk_disable_unprepare(wdt->clock);
> + return ret;
> +}
> +
> +static int zx2967_wdt_remove(struct platform_device *pdev)
> +{
> + struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
> +
> + watchdog_unregister_device(&wdt->wdt_device);
> + clk_disable_unprepare(wdt->clock);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_wdt_match[] = {
> + { .compatible = "zte,zx296718-wdt", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
> +
> +static struct platform_driver zx2967_wdt_driver = {
> + .probe = zx2967_wdt_probe,
> + .remove = zx2967_wdt_remove,
> + .driver = {
> + .name = "zx2967-wdt",
> + .of_match_table = of_match_ptr(zx2967_wdt_match),
> + },
> +};
> +module_platform_driver(zx2967_wdt_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
> +MODULE_LICENSE("GPL v2");
>
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-05 0:06 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 0:06 UTC (permalink / raw)
To: linux-arm-kernel
On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> This patch adds watchdog controller driver for ZTE's zx2967 family.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> drivers/watchdog/Kconfig | 10 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 302 insertions(+)
> create mode 100644 drivers/watchdog/zx2967_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index acb00b5..05093a2 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
> To compile this driver as a module, choose M here: the
> module will be called aspeed_wdt.
>
> +config ZX2967_WATCHDOG
> + tristate "ZTE zx2967 SoCs watchdog support"
> + depends on ARCH_ZX
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support for the watchdog timer
> + in ZTE zx2967 SoCs.
> + To compile this driver as a module, choose M here: the
> + module will be called zx2967_wdt.
> +
> # AVR32 Architecture
>
> config AT32AP700X_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 0c3d35e..bf2d296 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
> obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
> obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
> obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
> +obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
>
> # AVR32 Architecture
> obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
> diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
> new file mode 100644
> index 0000000..e290d5a
> --- /dev/null
> +++ b/drivers/watchdog/zx2967_wdt.c
> @@ -0,0 +1,291 @@
> +/*
> + * watchdog driver for ZTE's zx2967 family
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/watchdog.h>
> +
> +#define ZX2967_WDT_CFG_REG 0x4
> +#define ZX2967_WDT_LOAD_REG 0x8
> +#define ZX2967_WDT_REFRESH_REG 0x18
> +#define ZX2967_WDT_START_REG 0x1c
> +
> +#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
> +
> +#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
> +#define ZX2967_WDT_START_EN 0x1
> +
> +/*
> + * Hardware magic number.
> + * When watchdog reg is written, the lowest 16 bits are valid, but
> + * the highest 16 bits should be always this number.
> + */
> +#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
> +#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
> +
> +#define ZX2967_WDT_DIV_DEFAULT 16
> +#define ZX2967_WDT_DEFAULT_TIMEOUT 32
> +#define ZX2967_WDT_MIN_TIMEOUT 1
> +#define ZX2967_WDT_MAX_TIMEOUT 524
> +#define ZX2967_WDT_MAX_COUNT 0xffff
> +
> +#define ZX2967_WDT_CLK_FREQ 0x8000
> +
> +#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
> +
> +struct zx2967_wdt {
> + struct watchdog_device wdt_device;
> + void __iomem *reg_base;
> + struct clk *clock;
> +};
> +
> +static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
> +{
> + return readl_relaxed(wdt->reg_base + reg);
> +}
> +
> +static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
> +{
> + writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
> +}
> +
> +static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
> + /*
> + * Bit 4-5, 1 and 2: refresh config info
> + * Bit 2-3, 1 and 2: refresh counter
> + * Bit 0-1, 1 and 2: refresh int-value
> + * we shift each group value between 1 and 2 to refresh all data.
> + */
> + val ^= ZX2967_WDT_REFRESH_MASK;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int
> +zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> + unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
> + u32 count;
> +
> + count = timeout * ZX2967_WDT_CLK_FREQ;
> + if (count > divisor * ZX2967_WDT_MAX_COUNT)
> + divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
> + count = DIV_ROUND_UP(count, divisor);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
> + ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
> + count & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_refresh(wdt);
> + wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
> +
> + return 0;
> +}
> +
> +static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val |= ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val &= ~ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int zx2967_wdt_start(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_set_timeout(wdd, wdd->timeout);
> + __zx2967_wdt_start(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_stop(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + __zx2967_wdt_stop(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_refresh(wdt);
> +
> + return 0;
> +}
> +
> +#define ZX2967_WDT_OPTIONS \
> + (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
> +static const struct watchdog_info zx2967_wdt_ident = {
> + .options = ZX2967_WDT_OPTIONS,
> + .identity = "zx2967 watchdog",
> +};
> +
> +static struct watchdog_ops zx2967_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = zx2967_wdt_start,
> + .stop = zx2967_wdt_stop,
> + .ping = zx2967_wdt_keepalive,
> + .set_timeout = zx2967_wdt_set_timeout,
> +};
> +
> +static void zx2967_wdt_reset_sysctrl(struct device *dev)
> +{
> + int ret;
> + void __iomem *regmap;
> + unsigned int offset, mask, config;
> + struct of_phandle_args out_args;
> +
> + ret = of_parse_phandle_with_fixed_args(dev->of_node,
> + "zte,wdt-reset-sysctrl", 3, 0, &out_args);
> + if (ret)
> + return;
> +
> + offset = out_args.args[0];
> + config = out_args.args[1];
> + mask = out_args.args[2];
> +
> + regmap = syscon_node_to_regmap(out_args.np);
> + if (IS_ERR(regmap)) {
> + of_node_put(out_args.np);
> + return;
> + }
> +
> + regmap_update_bits(regmap, offset, mask, config);
> + of_node_put(out_args.np);
> +}
> +
> +static int zx2967_wdt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct zx2967_wdt *wdt;
> + struct resource *base;
> + int ret;
> + struct reset_control *rstc;
> +
> + wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, wdt);
> +
> + wdt->wdt_device.info = &zx2967_wdt_ident;
> + wdt->wdt_device.ops = &zx2967_wdt_ops;
> + wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
> + wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
> + wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
> + wdt->wdt_device.parent = &pdev->dev;
> +
> + base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + wdt->reg_base = devm_ioremap_resource(dev, base);
> + if (IS_ERR(wdt->reg_base)) {
> + dev_err(dev, "ioremap failed\n");
> + return PTR_ERR(wdt->reg_base);
> + }
> +
> + zx2967_wdt_reset_sysctrl(dev);
> +
> + wdt->clock = devm_clk_get(dev, NULL);
> + if (IS_ERR(wdt->clock)) {
> + dev_err(dev, "failed to find watchdog clock source\n");
> + return PTR_ERR(wdt->clock);
> + }
> +
> + ret = clk_prepare_enable(wdt->clock);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable clock\n");
> + return ret;
> + }
> + clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
> +
> + rstc = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(rstc)) {
> + dev_err(dev, "failed to get rstc");
> + ret = PTR_ERR(rstc);
> + goto err;
> + }
> +
> + reset_control_assert(rstc);
> + reset_control_deassert(rstc);
> +
> + watchdog_set_drvdata(&wdt->wdt_device, wdt);
> + watchdog_init_timeout(&wdt->wdt_device,
> + ZX2967_WDT_DEFAULT_TIMEOUT, dev);
> + watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
> +
> + ret = watchdog_register_device(&wdt->wdt_device);
> + if (ret)
> + goto err;
> +
> + dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
> + wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
> +
> + return 0;
> +
> +err:
> + clk_disable_unprepare(wdt->clock);
> + return ret;
> +}
> +
> +static int zx2967_wdt_remove(struct platform_device *pdev)
> +{
> + struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
> +
> + watchdog_unregister_device(&wdt->wdt_device);
> + clk_disable_unprepare(wdt->clock);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_wdt_match[] = {
> + { .compatible = "zte,zx296718-wdt", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
> +
> +static struct platform_driver zx2967_wdt_driver = {
> + .probe = zx2967_wdt_probe,
> + .remove = zx2967_wdt_remove,
> + .driver = {
> + .name = "zx2967-wdt",
> + .of_match_table = of_match_ptr(zx2967_wdt_match),
> + },
> +};
> +module_platform_driver(zx2967_wdt_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
> +MODULE_LICENSE("GPL v2");
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
2017-02-05 0:05 ` Guenter Roeck
(?)
(?)
@ 2017-02-05 2:36 ` Baoyou Xie
2017-02-05 3:45 ` Shawn Guo
-1 siblings, 1 reply; 30+ messages in thread
From: Baoyou Xie @ 2017-02-05 2:36 UTC (permalink / raw)
To: Guenter Roeck
Cc: Jun Nie, wim, Rob Herring, Mark Rutland, Mathieu Poirier,
linux-arm Mailing List, linux-watchdog, devicetree,
Linux Kernel Mailing List, Shawn Guo, xie.baoyou, chen.chaokai,
wang.qiang01
[-- Attachment #1: Type: text/plain, Size: 1355 bytes --]
On 5 February 2017 at 08:05, Guenter Roeck <linux@roeck-us.net> wrote:
> On 02/03/2017 05:34 PM, Baoyou Xie wrote:
>
>> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
>> architecture maintainers, as they're parts of the core IP.
>>
>> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
>>
>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>
> I assume you'll submit this patch through the arm tree ?
>
> Could you please submit all three patches through your tree? Thanks a lot
:)
> Guenter
>
>
> ---
>> MAINTAINERS | 2 ++
>> 1 file changed, 2 insertions(+)
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index edfdea3..275c434 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -1990,11 +1990,13 @@ F: drivers/clk/zte/
>> F: drivers/reset/reset-zx2967.c
>> F: drivers/soc/zte/
>> F: drivers/thermal/zx*
>> +F: drivers/watchdog/zx2967_wdt.c
>> F: Documentation/devicetree/bindings/arm/zte.txt
>> F: Documentation/devicetree/bindings/clock/zx296702-clk.txt
>> F: Documentation/devicetree/bindings/reset/zte,zx2967-reset.txt
>> F: Documentation/devicetree/bindings/soc/zte/
>> F: Documentation/devicetree/bindings/thermal/zx*
>> +F: Documentation/devicetree/bindings/watchdog/zte,zx2967-wdt.txt
>> F: include/dt-bindings/soc/zx*.h
>>
>> ARM/ZYNQ ARCHITECTURE
>>
>>
>
[-- Attachment #2: Type: text/html, Size: 2518 bytes --]
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
2017-02-05 2:36 ` Baoyou Xie
@ 2017-02-05 3:45 ` Shawn Guo
0 siblings, 0 replies; 30+ messages in thread
From: Shawn Guo @ 2017-02-05 3:45 UTC (permalink / raw)
To: Baoyou Xie
Cc: Guenter Roeck, Jun Nie, wim, Rob Herring, Mark Rutland,
Mathieu Poirier, linux-arm Mailing List, linux-watchdog,
devicetree, Linux Kernel Mailing List, xie.baoyou, chen.chaokai,
wang.qiang01
Hi Baoyou,
On Sun, Feb 05, 2017 at 10:36:38AM +0800, Baoyou Xie wrote:
> On 5 February 2017 at 08:05, Guenter Roeck <linux@roeck-us.net> wrote:
>
> > On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> >
> >> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
> >> architecture maintainers, as they're parts of the core IP.
> >>
> >> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> >>
> >
> > Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> >
> > I assume you'll submit this patch through the arm tree ?
> >
> Could you please submit all three patches through your tree? Thanks a lot
> :)
Patch #2 is the only one that Guenter is concerned about, as there are
other subsystem related updates on the file. I think Guenter's
suggestion is good, i.e. we have patch #1 and #3 go upstream through
watchdog tree, and later we update MAINTAINERS as needed via arm-soc
tree.
Shawn
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 3:45 ` Shawn Guo
0 siblings, 0 replies; 30+ messages in thread
From: Shawn Guo @ 2017-02-05 3:45 UTC (permalink / raw)
To: linux-arm-kernel
Hi Baoyou,
On Sun, Feb 05, 2017 at 10:36:38AM +0800, Baoyou Xie wrote:
> On 5 February 2017 at 08:05, Guenter Roeck <linux@roeck-us.net> wrote:
>
> > On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> >
> >> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
> >> architecture maintainers, as they're parts of the core IP.
> >>
> >> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> >>
> >
> > Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> >
> > I assume you'll submit this patch through the arm tree ?
> >
> Could you please submit all three patches through your tree? Thanks a lot
> :)
Patch #2 is the only one that Guenter is concerned about, as there are
other subsystem related updates on the file. I think Guenter's
suggestion is good, i.e. we have patch #1 and #3 go upstream through
watchdog tree, and later we update MAINTAINERS as needed via arm-soc
tree.
Shawn
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
2017-02-05 3:45 ` Shawn Guo
(?)
@ 2017-02-05 3:57 ` Baoyou Xie
-1 siblings, 0 replies; 30+ messages in thread
From: Baoyou Xie @ 2017-02-05 3:57 UTC (permalink / raw)
To: Shawn Guo
Cc: Guenter Roeck, Jun Nie, wim, Rob Herring, Mark Rutland,
Mathieu Poirier, linux-arm Mailing List, linux-watchdog,
devicetree, Linux Kernel Mailing List, xie.baoyou, chen.chaokai,
wang.qiang01
[-- Attachment #1: Type: text/plain, Size: 1091 bytes --]
On 5 February 2017 at 11:45, Shawn Guo <shawnguo@kernel.org> wrote:
> Hi Baoyou,
>
> On Sun, Feb 05, 2017 at 10:36:38AM +0800, Baoyou Xie wrote:
> > On 5 February 2017 at 08:05, Guenter Roeck <linux@roeck-us.net> wrote:
> >
> > > On 02/03/2017 05:34 PM, Baoyou Xie wrote:
> > >
> > >> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
> > >> architecture maintainers, as they're parts of the core IP.
> > >>
> > >> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> > >>
> > >
> > > Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> > >
> > > I assume you'll submit this patch through the arm tree ?
> > >
> > Could you please submit all three patches through your tree? Thanks a lot
> > :)
>
> Patch #2 is the only one that Guenter is concerned about, as there are
> other subsystem related updates on the file. I think Guenter's
> suggestion is good, i.e. we have patch #1 and #3 go upstream through
> watchdog tree, and later we update MAINTAINERS as needed via arm-soc
> tree.
>
> That's great :) It's better to submit this patch through *arm-soc* tree.
> Shawn
>
[-- Attachment #2: Type: text/html, Size: 2095 bytes --]
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
2017-02-05 3:45 ` Shawn Guo
(?)
@ 2017-02-05 4:29 ` Guenter Roeck
-1 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 4:29 UTC (permalink / raw)
To: Shawn Guo, Baoyou Xie
Cc: Jun Nie, wim, Rob Herring, Mark Rutland, Mathieu Poirier,
linux-arm Mailing List, linux-watchdog, devicetree,
Linux Kernel Mailing List, xie.baoyou, chen.chaokai,
wang.qiang01
On 02/04/2017 07:45 PM, Shawn Guo wrote:
> Hi Baoyou,
>
> On Sun, Feb 05, 2017 at 10:36:38AM +0800, Baoyou Xie wrote:
>> On 5 February 2017 at 08:05, Guenter Roeck <linux@roeck-us.net> wrote:
>>
>>> On 02/03/2017 05:34 PM, Baoyou Xie wrote:
>>>
>>>> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
>>>> architecture maintainers, as they're parts of the core IP.
>>>>
>>>> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
>>>>
>>>
>>> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>>>
>>> I assume you'll submit this patch through the arm tree ?
>>>
>> Could you please submit all three patches through your tree? Thanks a lot
>> :)
>
> Patch #2 is the only one that Guenter is concerned about, as there are
> other subsystem related updates on the file. I think Guenter's
> suggestion is good, i.e. we have patch #1 and #3 go upstream through
> watchdog tree, and later we update MAINTAINERS as needed via arm-soc
> tree.
>
Yes. One of the problems is that the patch doesn't apply to my tree
(which is based on v4.10-rc3), and it doesn't have a common anchestor,
meaning it is most likely not based on mainline. I would prefer to avoid
conflicts with the arm tree if possible.
Guenter
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 4:29 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 4:29 UTC (permalink / raw)
To: Shawn Guo, Baoyou Xie
Cc: Jun Nie, wim-IQzOog9fTRqzQB+pC5nmwQ, Rob Herring, Mark Rutland,
Mathieu Poirier, linux-arm Mailing List,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA, devicetree,
Linux Kernel Mailing List, xie.baoyou,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
On 02/04/2017 07:45 PM, Shawn Guo wrote:
> Hi Baoyou,
>
> On Sun, Feb 05, 2017 at 10:36:38AM +0800, Baoyou Xie wrote:
>> On 5 February 2017 at 08:05, Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org> wrote:
>>
>>> On 02/03/2017 05:34 PM, Baoyou Xie wrote:
>>>
>>>> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
>>>> architecture maintainers, as they're parts of the core IP.
>>>>
>>>> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
>>>>
>>>
>>> Reviewed-by: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
>>>
>>> I assume you'll submit this patch through the arm tree ?
>>>
>> Could you please submit all three patches through your tree? Thanks a lot
>> :)
>
> Patch #2 is the only one that Guenter is concerned about, as there are
> other subsystem related updates on the file. I think Guenter's
> suggestion is good, i.e. we have patch #1 and #3 go upstream through
> watchdog tree, and later we update MAINTAINERS as needed via arm-soc
> tree.
>
Yes. One of the problems is that the patch doesn't apply to my tree
(which is based on v4.10-rc3), and it doesn't have a common anchestor,
meaning it is most likely not based on mainline. I would prefer to avoid
conflicts with the arm tree if possible.
Guenter
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 4:29 ` Guenter Roeck
0 siblings, 0 replies; 30+ messages in thread
From: Guenter Roeck @ 2017-02-05 4:29 UTC (permalink / raw)
To: linux-arm-kernel
On 02/04/2017 07:45 PM, Shawn Guo wrote:
> Hi Baoyou,
>
> On Sun, Feb 05, 2017 at 10:36:38AM +0800, Baoyou Xie wrote:
>> On 5 February 2017 at 08:05, Guenter Roeck <linux@roeck-us.net> wrote:
>>
>>> On 02/03/2017 05:34 PM, Baoyou Xie wrote:
>>>
>>>> Add the zx2967 watchdog controller driver as maintained by ARM ZTE
>>>> architecture maintainers, as they're parts of the core IP.
>>>>
>>>> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
>>>>
>>>
>>> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
>>>
>>> I assume you'll submit this patch through the arm tree ?
>>>
>> Could you please submit all three patches through your tree? Thanks a lot
>> :)
>
> Patch #2 is the only one that Guenter is concerned about, as there are
> other subsystem related updates on the file. I think Guenter's
> suggestion is good, i.e. we have patch #1 and #3 go upstream through
> watchdog tree, and later we update MAINTAINERS as needed via arm-soc
> tree.
>
Yes. One of the problems is that the patch doesn't apply to my tree
(which is based on v4.10-rc3), and it doesn't have a common anchestor,
meaning it is most likely not based on mainline. I would prefer to avoid
conflicts with the arm tree if possible.
Guenter
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 4:54 ` Shawn Guo
0 siblings, 0 replies; 30+ messages in thread
From: Shawn Guo @ 2017-02-05 4:54 UTC (permalink / raw)
To: Guenter Roeck
Cc: Baoyou Xie, Jun Nie, wim, Rob Herring, Mark Rutland,
Mathieu Poirier, linux-arm Mailing List, linux-watchdog,
devicetree, Linux Kernel Mailing List, xie.baoyou, chen.chaokai,
wang.qiang01
Hi Guenter,
On Sat, Feb 04, 2017 at 08:29:27PM -0800, Guenter Roeck wrote:
> Yes. One of the problems is that the patch doesn't apply to my tree
> (which is based on v4.10-rc3), and it doesn't have a common anchestor,
> meaning it is most likely not based on mainline. I would prefer to avoid
> conflicts with the arm tree if possible.
Understood. You only need to handle patch #1 and #3, and we will sort
out MAINTAINERS update separately. Thanks.
Shawn
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 4:54 ` Shawn Guo
0 siblings, 0 replies; 30+ messages in thread
From: Shawn Guo @ 2017-02-05 4:54 UTC (permalink / raw)
To: Guenter Roeck
Cc: Baoyou Xie, Jun Nie, wim-IQzOog9fTRqzQB+pC5nmwQ, Rob Herring,
Mark Rutland, Mathieu Poirier, linux-arm Mailing List,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA, devicetree,
Linux Kernel Mailing List, xie.baoyou,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
Hi Guenter,
On Sat, Feb 04, 2017 at 08:29:27PM -0800, Guenter Roeck wrote:
> Yes. One of the problems is that the patch doesn't apply to my tree
> (which is based on v4.10-rc3), and it doesn't have a common anchestor,
> meaning it is most likely not based on mainline. I would prefer to avoid
> conflicts with the arm tree if possible.
Understood. You only need to handle patch #1 and #3, and we will sort
out MAINTAINERS update separately. Thanks.
Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture
@ 2017-02-05 4:54 ` Shawn Guo
0 siblings, 0 replies; 30+ messages in thread
From: Shawn Guo @ 2017-02-05 4:54 UTC (permalink / raw)
To: linux-arm-kernel
Hi Guenter,
On Sat, Feb 04, 2017 at 08:29:27PM -0800, Guenter Roeck wrote:
> Yes. One of the problems is that the patch doesn't apply to my tree
> (which is based on v4.10-rc3), and it doesn't have a common anchestor,
> meaning it is most likely not based on mainline. I would prefer to avoid
> conflicts with the arm tree if possible.
Understood. You only need to handle patch #1 and #3, and we will sort
out MAINTAINERS update separately. Thanks.
Shawn
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-06 17:13 ` Mathieu Poirier
0 siblings, 0 replies; 30+ messages in thread
From: Mathieu Poirier @ 2017-02-06 17:13 UTC (permalink / raw)
To: Baoyou Xie
Cc: jun.nie, wim, linux, robh+dt, mark.rutland, linux-arm-kernel,
linux-watchdog, devicetree, linux-kernel, shawnguo, xie.baoyou,
chen.chaokai, wang.qiang01
On Sat, Feb 04, 2017 at 09:34:15AM +0800, Baoyou Xie wrote:
> This patch adds watchdog controller driver for ZTE's zx2967 family.
>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> ---
> drivers/watchdog/Kconfig | 10 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 302 insertions(+)
> create mode 100644 drivers/watchdog/zx2967_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index acb00b5..05093a2 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
> To compile this driver as a module, choose M here: the
> module will be called aspeed_wdt.
>
> +config ZX2967_WATCHDOG
> + tristate "ZTE zx2967 SoCs watchdog support"
> + depends on ARCH_ZX
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support for the watchdog timer
> + in ZTE zx2967 SoCs.
> + To compile this driver as a module, choose M here: the
> + module will be called zx2967_wdt.
> +
> # AVR32 Architecture
>
> config AT32AP700X_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 0c3d35e..bf2d296 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
> obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
> obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
> obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
> +obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
>
> # AVR32 Architecture
> obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
> diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
> new file mode 100644
> index 0000000..e290d5a
> --- /dev/null
> +++ b/drivers/watchdog/zx2967_wdt.c
> @@ -0,0 +1,291 @@
> +/*
> + * watchdog driver for ZTE's zx2967 family
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/watchdog.h>
> +
> +#define ZX2967_WDT_CFG_REG 0x4
> +#define ZX2967_WDT_LOAD_REG 0x8
> +#define ZX2967_WDT_REFRESH_REG 0x18
> +#define ZX2967_WDT_START_REG 0x1c
> +
> +#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
> +
> +#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
> +#define ZX2967_WDT_START_EN 0x1
> +
> +/*
> + * Hardware magic number.
> + * When watchdog reg is written, the lowest 16 bits are valid, but
> + * the highest 16 bits should be always this number.
> + */
> +#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
> +#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
> +
> +#define ZX2967_WDT_DIV_DEFAULT 16
> +#define ZX2967_WDT_DEFAULT_TIMEOUT 32
> +#define ZX2967_WDT_MIN_TIMEOUT 1
> +#define ZX2967_WDT_MAX_TIMEOUT 524
> +#define ZX2967_WDT_MAX_COUNT 0xffff
> +
> +#define ZX2967_WDT_CLK_FREQ 0x8000
> +
> +#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
> +
> +struct zx2967_wdt {
> + struct watchdog_device wdt_device;
> + void __iomem *reg_base;
> + struct clk *clock;
> +};
> +
> +static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
> +{
> + return readl_relaxed(wdt->reg_base + reg);
> +}
> +
> +static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
> +{
> + writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
> +}
> +
> +static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
> + /*
> + * Bit 4-5, 1 and 2: refresh config info
> + * Bit 2-3, 1 and 2: refresh counter
> + * Bit 0-1, 1 and 2: refresh int-value
> + * we shift each group value between 1 and 2 to refresh all data.
> + */
> + val ^= ZX2967_WDT_REFRESH_MASK;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int
> +zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> + unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
> + u32 count;
> +
> + count = timeout * ZX2967_WDT_CLK_FREQ;
> + if (count > divisor * ZX2967_WDT_MAX_COUNT)
> + divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
> + count = DIV_ROUND_UP(count, divisor);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
> + ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
> + count & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_refresh(wdt);
> + wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
> +
> + return 0;
> +}
> +
> +static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val |= ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val &= ~ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int zx2967_wdt_start(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_set_timeout(wdd, wdd->timeout);
> + __zx2967_wdt_start(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_stop(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + __zx2967_wdt_stop(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_refresh(wdt);
> +
> + return 0;
> +}
> +
> +#define ZX2967_WDT_OPTIONS \
> + (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
> +static const struct watchdog_info zx2967_wdt_ident = {
> + .options = ZX2967_WDT_OPTIONS,
> + .identity = "zx2967 watchdog",
> +};
> +
> +static struct watchdog_ops zx2967_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = zx2967_wdt_start,
> + .stop = zx2967_wdt_stop,
> + .ping = zx2967_wdt_keepalive,
> + .set_timeout = zx2967_wdt_set_timeout,
> +};
> +
> +static void zx2967_wdt_reset_sysctrl(struct device *dev)
> +{
> + int ret;
> + void __iomem *regmap;
> + unsigned int offset, mask, config;
> + struct of_phandle_args out_args;
> +
> + ret = of_parse_phandle_with_fixed_args(dev->of_node,
> + "zte,wdt-reset-sysctrl", 3, 0, &out_args);
> + if (ret)
> + return;
> +
> + offset = out_args.args[0];
> + config = out_args.args[1];
> + mask = out_args.args[2];
> +
> + regmap = syscon_node_to_regmap(out_args.np);
> + if (IS_ERR(regmap)) {
> + of_node_put(out_args.np);
> + return;
> + }
> +
> + regmap_update_bits(regmap, offset, mask, config);
> + of_node_put(out_args.np);
> +}
> +
> +static int zx2967_wdt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct zx2967_wdt *wdt;
> + struct resource *base;
> + int ret;
> + struct reset_control *rstc;
> +
> + wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, wdt);
> +
> + wdt->wdt_device.info = &zx2967_wdt_ident;
> + wdt->wdt_device.ops = &zx2967_wdt_ops;
> + wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
> + wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
> + wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
> + wdt->wdt_device.parent = &pdev->dev;
> +
> + base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + wdt->reg_base = devm_ioremap_resource(dev, base);
> + if (IS_ERR(wdt->reg_base)) {
> + dev_err(dev, "ioremap failed\n");
> + return PTR_ERR(wdt->reg_base);
> + }
> +
> + zx2967_wdt_reset_sysctrl(dev);
> +
> + wdt->clock = devm_clk_get(dev, NULL);
> + if (IS_ERR(wdt->clock)) {
> + dev_err(dev, "failed to find watchdog clock source\n");
> + return PTR_ERR(wdt->clock);
> + }
> +
> + ret = clk_prepare_enable(wdt->clock);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable clock\n");
> + return ret;
> + }
> + clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
> +
> + rstc = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(rstc)) {
> + dev_err(dev, "failed to get rstc");
> + ret = PTR_ERR(rstc);
> + goto err;
> + }
> +
> + reset_control_assert(rstc);
> + reset_control_deassert(rstc);
> +
> + watchdog_set_drvdata(&wdt->wdt_device, wdt);
> + watchdog_init_timeout(&wdt->wdt_device,
> + ZX2967_WDT_DEFAULT_TIMEOUT, dev);
> + watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
> +
> + ret = watchdog_register_device(&wdt->wdt_device);
> + if (ret)
> + goto err;
> +
> + dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
> + wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
> +
> + return 0;
> +
> +err:
> + clk_disable_unprepare(wdt->clock);
> + return ret;
> +}
> +
> +static int zx2967_wdt_remove(struct platform_device *pdev)
> +{
> + struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
> +
> + watchdog_unregister_device(&wdt->wdt_device);
> + clk_disable_unprepare(wdt->clock);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_wdt_match[] = {
> + { .compatible = "zte,zx296718-wdt", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
> +
> +static struct platform_driver zx2967_wdt_driver = {
> + .probe = zx2967_wdt_probe,
> + .remove = zx2967_wdt_remove,
> + .driver = {
> + .name = "zx2967-wdt",
> + .of_match_table = of_match_ptr(zx2967_wdt_match),
> + },
> +};
> +module_platform_driver(zx2967_wdt_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 30+ messages in thread
* Re: [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-06 17:13 ` Mathieu Poirier
0 siblings, 0 replies; 30+ messages in thread
From: Mathieu Poirier @ 2017-02-06 17:13 UTC (permalink / raw)
To: Baoyou Xie
Cc: jun.nie-QSEj5FYQhm4dnm+yROfE0A, wim-IQzOog9fTRqzQB+pC5nmwQ,
linux-0h96xk9xTtrk1uMJSBkQmQ, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-watchdog-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
On Sat, Feb 04, 2017 at 09:34:15AM +0800, Baoyou Xie wrote:
> This patch adds watchdog controller driver for ZTE's zx2967 family.
>
Reviewed-by: Mathieu Poirier <mathieu.poirier-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> ---
> drivers/watchdog/Kconfig | 10 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 302 insertions(+)
> create mode 100644 drivers/watchdog/zx2967_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index acb00b5..05093a2 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
> To compile this driver as a module, choose M here: the
> module will be called aspeed_wdt.
>
> +config ZX2967_WATCHDOG
> + tristate "ZTE zx2967 SoCs watchdog support"
> + depends on ARCH_ZX
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support for the watchdog timer
> + in ZTE zx2967 SoCs.
> + To compile this driver as a module, choose M here: the
> + module will be called zx2967_wdt.
> +
> # AVR32 Architecture
>
> config AT32AP700X_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 0c3d35e..bf2d296 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
> obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
> obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
> obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
> +obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
>
> # AVR32 Architecture
> obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
> diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
> new file mode 100644
> index 0000000..e290d5a
> --- /dev/null
> +++ b/drivers/watchdog/zx2967_wdt.c
> @@ -0,0 +1,291 @@
> +/*
> + * watchdog driver for ZTE's zx2967 family
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/watchdog.h>
> +
> +#define ZX2967_WDT_CFG_REG 0x4
> +#define ZX2967_WDT_LOAD_REG 0x8
> +#define ZX2967_WDT_REFRESH_REG 0x18
> +#define ZX2967_WDT_START_REG 0x1c
> +
> +#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
> +
> +#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
> +#define ZX2967_WDT_START_EN 0x1
> +
> +/*
> + * Hardware magic number.
> + * When watchdog reg is written, the lowest 16 bits are valid, but
> + * the highest 16 bits should be always this number.
> + */
> +#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
> +#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
> +
> +#define ZX2967_WDT_DIV_DEFAULT 16
> +#define ZX2967_WDT_DEFAULT_TIMEOUT 32
> +#define ZX2967_WDT_MIN_TIMEOUT 1
> +#define ZX2967_WDT_MAX_TIMEOUT 524
> +#define ZX2967_WDT_MAX_COUNT 0xffff
> +
> +#define ZX2967_WDT_CLK_FREQ 0x8000
> +
> +#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
> +
> +struct zx2967_wdt {
> + struct watchdog_device wdt_device;
> + void __iomem *reg_base;
> + struct clk *clock;
> +};
> +
> +static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
> +{
> + return readl_relaxed(wdt->reg_base + reg);
> +}
> +
> +static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
> +{
> + writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
> +}
> +
> +static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
> + /*
> + * Bit 4-5, 1 and 2: refresh config info
> + * Bit 2-3, 1 and 2: refresh counter
> + * Bit 0-1, 1 and 2: refresh int-value
> + * we shift each group value between 1 and 2 to refresh all data.
> + */
> + val ^= ZX2967_WDT_REFRESH_MASK;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int
> +zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> + unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
> + u32 count;
> +
> + count = timeout * ZX2967_WDT_CLK_FREQ;
> + if (count > divisor * ZX2967_WDT_MAX_COUNT)
> + divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
> + count = DIV_ROUND_UP(count, divisor);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
> + ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
> + count & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_refresh(wdt);
> + wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
> +
> + return 0;
> +}
> +
> +static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val |= ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val &= ~ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int zx2967_wdt_start(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_set_timeout(wdd, wdd->timeout);
> + __zx2967_wdt_start(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_stop(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + __zx2967_wdt_stop(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_refresh(wdt);
> +
> + return 0;
> +}
> +
> +#define ZX2967_WDT_OPTIONS \
> + (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
> +static const struct watchdog_info zx2967_wdt_ident = {
> + .options = ZX2967_WDT_OPTIONS,
> + .identity = "zx2967 watchdog",
> +};
> +
> +static struct watchdog_ops zx2967_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = zx2967_wdt_start,
> + .stop = zx2967_wdt_stop,
> + .ping = zx2967_wdt_keepalive,
> + .set_timeout = zx2967_wdt_set_timeout,
> +};
> +
> +static void zx2967_wdt_reset_sysctrl(struct device *dev)
> +{
> + int ret;
> + void __iomem *regmap;
> + unsigned int offset, mask, config;
> + struct of_phandle_args out_args;
> +
> + ret = of_parse_phandle_with_fixed_args(dev->of_node,
> + "zte,wdt-reset-sysctrl", 3, 0, &out_args);
> + if (ret)
> + return;
> +
> + offset = out_args.args[0];
> + config = out_args.args[1];
> + mask = out_args.args[2];
> +
> + regmap = syscon_node_to_regmap(out_args.np);
> + if (IS_ERR(regmap)) {
> + of_node_put(out_args.np);
> + return;
> + }
> +
> + regmap_update_bits(regmap, offset, mask, config);
> + of_node_put(out_args.np);
> +}
> +
> +static int zx2967_wdt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct zx2967_wdt *wdt;
> + struct resource *base;
> + int ret;
> + struct reset_control *rstc;
> +
> + wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, wdt);
> +
> + wdt->wdt_device.info = &zx2967_wdt_ident;
> + wdt->wdt_device.ops = &zx2967_wdt_ops;
> + wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
> + wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
> + wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
> + wdt->wdt_device.parent = &pdev->dev;
> +
> + base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + wdt->reg_base = devm_ioremap_resource(dev, base);
> + if (IS_ERR(wdt->reg_base)) {
> + dev_err(dev, "ioremap failed\n");
> + return PTR_ERR(wdt->reg_base);
> + }
> +
> + zx2967_wdt_reset_sysctrl(dev);
> +
> + wdt->clock = devm_clk_get(dev, NULL);
> + if (IS_ERR(wdt->clock)) {
> + dev_err(dev, "failed to find watchdog clock source\n");
> + return PTR_ERR(wdt->clock);
> + }
> +
> + ret = clk_prepare_enable(wdt->clock);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable clock\n");
> + return ret;
> + }
> + clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
> +
> + rstc = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(rstc)) {
> + dev_err(dev, "failed to get rstc");
> + ret = PTR_ERR(rstc);
> + goto err;
> + }
> +
> + reset_control_assert(rstc);
> + reset_control_deassert(rstc);
> +
> + watchdog_set_drvdata(&wdt->wdt_device, wdt);
> + watchdog_init_timeout(&wdt->wdt_device,
> + ZX2967_WDT_DEFAULT_TIMEOUT, dev);
> + watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
> +
> + ret = watchdog_register_device(&wdt->wdt_device);
> + if (ret)
> + goto err;
> +
> + dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
> + wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
> +
> + return 0;
> +
> +err:
> + clk_disable_unprepare(wdt->clock);
> + return ret;
> +}
> +
> +static int zx2967_wdt_remove(struct platform_device *pdev)
> +{
> + struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
> +
> + watchdog_unregister_device(&wdt->wdt_device);
> + clk_disable_unprepare(wdt->clock);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_wdt_match[] = {
> + { .compatible = "zte,zx296718-wdt", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
> +
> +static struct platform_driver zx2967_wdt_driver = {
> + .probe = zx2967_wdt_probe,
> + .remove = zx2967_wdt_remove,
> + .driver = {
> + .name = "zx2967-wdt",
> + .of_match_table = of_match_ptr(zx2967_wdt_match),
> + },
> +};
> +module_platform_driver(zx2967_wdt_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 30+ messages in thread
* [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
@ 2017-02-06 17:13 ` Mathieu Poirier
0 siblings, 0 replies; 30+ messages in thread
From: Mathieu Poirier @ 2017-02-06 17:13 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Feb 04, 2017 at 09:34:15AM +0800, Baoyou Xie wrote:
> This patch adds watchdog controller driver for ZTE's zx2967 family.
>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> ---
> drivers/watchdog/Kconfig | 10 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/zx2967_wdt.c | 291 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 302 insertions(+)
> create mode 100644 drivers/watchdog/zx2967_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index acb00b5..05093a2 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -714,6 +714,16 @@ config ASPEED_WATCHDOG
> To compile this driver as a module, choose M here: the
> module will be called aspeed_wdt.
>
> +config ZX2967_WATCHDOG
> + tristate "ZTE zx2967 SoCs watchdog support"
> + depends on ARCH_ZX
> + select WATCHDOG_CORE
> + help
> + Say Y here to include support for the watchdog timer
> + in ZTE zx2967 SoCs.
> + To compile this driver as a module, choose M here: the
> + module will be called zx2967_wdt.
> +
> # AVR32 Architecture
>
> config AT32AP700X_WDT
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 0c3d35e..bf2d296 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -82,6 +82,7 @@ obj-$(CONFIG_BCM7038_WDT) += bcm7038_wdt.o
> obj-$(CONFIG_ATLAS7_WATCHDOG) += atlas7_wdt.o
> obj-$(CONFIG_RENESAS_WDT) += renesas_wdt.o
> obj-$(CONFIG_ASPEED_WATCHDOG) += aspeed_wdt.o
> +obj-$(CONFIG_ZX2967_WATCHDOG) += zx2967_wdt.o
>
> # AVR32 Architecture
> obj-$(CONFIG_AT32AP700X_WDT) += at32ap700x_wdt.o
> diff --git a/drivers/watchdog/zx2967_wdt.c b/drivers/watchdog/zx2967_wdt.c
> new file mode 100644
> index 0000000..e290d5a
> --- /dev/null
> +++ b/drivers/watchdog/zx2967_wdt.c
> @@ -0,0 +1,291 @@
> +/*
> + * watchdog driver for ZTE's zx2967 family
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + *
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/watchdog.h>
> +
> +#define ZX2967_WDT_CFG_REG 0x4
> +#define ZX2967_WDT_LOAD_REG 0x8
> +#define ZX2967_WDT_REFRESH_REG 0x18
> +#define ZX2967_WDT_START_REG 0x1c
> +
> +#define ZX2967_WDT_REFRESH_MASK GENMASK(5, 0)
> +
> +#define ZX2967_WDT_CFG_DIV(n) ((((n) & 0xff) - 1) << 8)
> +#define ZX2967_WDT_START_EN 0x1
> +
> +/*
> + * Hardware magic number.
> + * When watchdog reg is written, the lowest 16 bits are valid, but
> + * the highest 16 bits should be always this number.
> + */
> +#define ZX2967_WDT_WRITEKEY (0x1234 << 16)
> +#define ZX2967_WDT_VAL_MASK GENMASK(15, 0)
> +
> +#define ZX2967_WDT_DIV_DEFAULT 16
> +#define ZX2967_WDT_DEFAULT_TIMEOUT 32
> +#define ZX2967_WDT_MIN_TIMEOUT 1
> +#define ZX2967_WDT_MAX_TIMEOUT 524
> +#define ZX2967_WDT_MAX_COUNT 0xffff
> +
> +#define ZX2967_WDT_CLK_FREQ 0x8000
> +
> +#define ZX2967_WDT_FLAG_REBOOT_MON BIT(0)
> +
> +struct zx2967_wdt {
> + struct watchdog_device wdt_device;
> + void __iomem *reg_base;
> + struct clk *clock;
> +};
> +
> +static inline u32 zx2967_wdt_readl(struct zx2967_wdt *wdt, u16 reg)
> +{
> + return readl_relaxed(wdt->reg_base + reg);
> +}
> +
> +static inline void zx2967_wdt_writel(struct zx2967_wdt *wdt, u16 reg, u32 val)
> +{
> + writel_relaxed(val | ZX2967_WDT_WRITEKEY, wdt->reg_base + reg);
> +}
> +
> +static void zx2967_wdt_refresh(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_REFRESH_REG);
> + /*
> + * Bit 4-5, 1 and 2: refresh config info
> + * Bit 2-3, 1 and 2: refresh counter
> + * Bit 0-1, 1 and 2: refresh int-value
> + * we shift each group value between 1 and 2 to refresh all data.
> + */
> + val ^= ZX2967_WDT_REFRESH_MASK;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_REFRESH_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int
> +zx2967_wdt_set_timeout(struct watchdog_device *wdd, unsigned int timeout)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> + unsigned int divisor = ZX2967_WDT_DIV_DEFAULT;
> + u32 count;
> +
> + count = timeout * ZX2967_WDT_CLK_FREQ;
> + if (count > divisor * ZX2967_WDT_MAX_COUNT)
> + divisor = DIV_ROUND_UP(count, ZX2967_WDT_MAX_COUNT);
> + count = DIV_ROUND_UP(count, divisor);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_CFG_REG,
> + ZX2967_WDT_CFG_DIV(divisor) & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_writel(wdt, ZX2967_WDT_LOAD_REG,
> + count & ZX2967_WDT_VAL_MASK);
> + zx2967_wdt_refresh(wdt);
> + wdd->timeout = (count * divisor) / ZX2967_WDT_CLK_FREQ;
> +
> + return 0;
> +}
> +
> +static void __zx2967_wdt_start(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val |= ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static void __zx2967_wdt_stop(struct zx2967_wdt *wdt)
> +{
> + u32 val;
> +
> + val = zx2967_wdt_readl(wdt, ZX2967_WDT_START_REG);
> + val &= ~ZX2967_WDT_START_EN;
> + zx2967_wdt_writel(wdt, ZX2967_WDT_START_REG,
> + val & ZX2967_WDT_VAL_MASK);
> +}
> +
> +static int zx2967_wdt_start(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_set_timeout(wdd, wdd->timeout);
> + __zx2967_wdt_start(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_stop(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + __zx2967_wdt_stop(wdt);
> +
> + return 0;
> +}
> +
> +static int zx2967_wdt_keepalive(struct watchdog_device *wdd)
> +{
> + struct zx2967_wdt *wdt = watchdog_get_drvdata(wdd);
> +
> + zx2967_wdt_refresh(wdt);
> +
> + return 0;
> +}
> +
> +#define ZX2967_WDT_OPTIONS \
> + (WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING | WDIOF_MAGICCLOSE)
> +static const struct watchdog_info zx2967_wdt_ident = {
> + .options = ZX2967_WDT_OPTIONS,
> + .identity = "zx2967 watchdog",
> +};
> +
> +static struct watchdog_ops zx2967_wdt_ops = {
> + .owner = THIS_MODULE,
> + .start = zx2967_wdt_start,
> + .stop = zx2967_wdt_stop,
> + .ping = zx2967_wdt_keepalive,
> + .set_timeout = zx2967_wdt_set_timeout,
> +};
> +
> +static void zx2967_wdt_reset_sysctrl(struct device *dev)
> +{
> + int ret;
> + void __iomem *regmap;
> + unsigned int offset, mask, config;
> + struct of_phandle_args out_args;
> +
> + ret = of_parse_phandle_with_fixed_args(dev->of_node,
> + "zte,wdt-reset-sysctrl", 3, 0, &out_args);
> + if (ret)
> + return;
> +
> + offset = out_args.args[0];
> + config = out_args.args[1];
> + mask = out_args.args[2];
> +
> + regmap = syscon_node_to_regmap(out_args.np);
> + if (IS_ERR(regmap)) {
> + of_node_put(out_args.np);
> + return;
> + }
> +
> + regmap_update_bits(regmap, offset, mask, config);
> + of_node_put(out_args.np);
> +}
> +
> +static int zx2967_wdt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct zx2967_wdt *wdt;
> + struct resource *base;
> + int ret;
> + struct reset_control *rstc;
> +
> + wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL);
> + if (!wdt)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, wdt);
> +
> + wdt->wdt_device.info = &zx2967_wdt_ident;
> + wdt->wdt_device.ops = &zx2967_wdt_ops;
> + wdt->wdt_device.timeout = ZX2967_WDT_DEFAULT_TIMEOUT;
> + wdt->wdt_device.max_timeout = ZX2967_WDT_MAX_TIMEOUT;
> + wdt->wdt_device.min_timeout = ZX2967_WDT_MIN_TIMEOUT;
> + wdt->wdt_device.parent = &pdev->dev;
> +
> + base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + wdt->reg_base = devm_ioremap_resource(dev, base);
> + if (IS_ERR(wdt->reg_base)) {
> + dev_err(dev, "ioremap failed\n");
> + return PTR_ERR(wdt->reg_base);
> + }
> +
> + zx2967_wdt_reset_sysctrl(dev);
> +
> + wdt->clock = devm_clk_get(dev, NULL);
> + if (IS_ERR(wdt->clock)) {
> + dev_err(dev, "failed to find watchdog clock source\n");
> + return PTR_ERR(wdt->clock);
> + }
> +
> + ret = clk_prepare_enable(wdt->clock);
> + if (ret < 0) {
> + dev_err(dev, "failed to enable clock\n");
> + return ret;
> + }
> + clk_set_rate(wdt->clock, ZX2967_WDT_CLK_FREQ);
> +
> + rstc = devm_reset_control_get(dev, NULL);
> + if (IS_ERR(rstc)) {
> + dev_err(dev, "failed to get rstc");
> + ret = PTR_ERR(rstc);
> + goto err;
> + }
> +
> + reset_control_assert(rstc);
> + reset_control_deassert(rstc);
> +
> + watchdog_set_drvdata(&wdt->wdt_device, wdt);
> + watchdog_init_timeout(&wdt->wdt_device,
> + ZX2967_WDT_DEFAULT_TIMEOUT, dev);
> + watchdog_set_nowayout(&wdt->wdt_device, WATCHDOG_NOWAYOUT);
> +
> + ret = watchdog_register_device(&wdt->wdt_device);
> + if (ret)
> + goto err;
> +
> + dev_info(dev, "watchdog enabled (timeout=%d sec, nowayout=%d)",
> + wdt->wdt_device.timeout, WATCHDOG_NOWAYOUT);
> +
> + return 0;
> +
> +err:
> + clk_disable_unprepare(wdt->clock);
> + return ret;
> +}
> +
> +static int zx2967_wdt_remove(struct platform_device *pdev)
> +{
> + struct zx2967_wdt *wdt = platform_get_drvdata(pdev);
> +
> + watchdog_unregister_device(&wdt->wdt_device);
> + clk_disable_unprepare(wdt->clock);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id zx2967_wdt_match[] = {
> + { .compatible = "zte,zx296718-wdt", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, zx2967_wdt_match);
> +
> +static struct platform_driver zx2967_wdt_driver = {
> + .probe = zx2967_wdt_probe,
> + .remove = zx2967_wdt_remove,
> + .driver = {
> + .name = "zx2967-wdt",
> + .of_match_table = of_match_ptr(zx2967_wdt_match),
> + },
> +};
> +module_platform_driver(zx2967_wdt_driver);
> +
> +MODULE_AUTHOR("Baoyou Xie <baoyou.xie@linaro.org>");
> +MODULE_DESCRIPTION("ZTE zx2967 Watchdog Device Driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 30+ messages in thread
end of thread, other threads:[~2017-02-06 17:14 UTC | newest]
Thread overview: 30+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-02-04 1:34 [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller Baoyou Xie
2017-02-04 1:34 ` Baoyou Xie
2017-02-04 1:34 ` Baoyou Xie
2017-02-04 1:34 ` [PATCH v9 2/3] MAINTAINERS: add zx2967 watchdog controller driver to ARM ZTE architecture Baoyou Xie
2017-02-04 1:34 ` Baoyou Xie
2017-02-04 1:34 ` Baoyou Xie
2017-02-05 0:05 ` Guenter Roeck
2017-02-05 0:05 ` Guenter Roeck
2017-02-05 0:05 ` Guenter Roeck
2017-02-05 2:36 ` Baoyou Xie
2017-02-05 3:45 ` Shawn Guo
2017-02-05 3:45 ` Shawn Guo
2017-02-05 3:57 ` Baoyou Xie
2017-02-05 4:29 ` Guenter Roeck
2017-02-05 4:29 ` Guenter Roeck
2017-02-05 4:29 ` Guenter Roeck
2017-02-05 4:54 ` Shawn Guo
2017-02-05 4:54 ` Shawn Guo
2017-02-05 4:54 ` Shawn Guo
2017-02-04 1:34 ` [PATCH v9 3/3] watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family Baoyou Xie
2017-02-04 1:34 ` Baoyou Xie
2017-02-05 0:06 ` Guenter Roeck
2017-02-05 0:06 ` Guenter Roeck
2017-02-05 0:06 ` Guenter Roeck
2017-02-06 17:13 ` Mathieu Poirier
2017-02-06 17:13 ` Mathieu Poirier
2017-02-06 17:13 ` Mathieu Poirier
2017-02-05 0:04 ` [PATCH v9 1/3] dt: bindings: add documentation for zx2967 family watchdog controller Guenter Roeck
2017-02-05 0:04 ` Guenter Roeck
2017-02-05 0:04 ` Guenter Roeck
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.