From mboxrd@z Thu Jan 1 00:00:00 1970 From: harninder.rai@nxp.com (Harninder Rai) Date: Thu, 23 Mar 2017 20:19:28 +0530 Subject: [PATCH][v2] arm64: dts: Add support for FSL's LS1088A SoC Message-ID: <1490280568-13695-1-git-send-email-harninder.rai@nxp.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org LS1088A contains eight ARM v8 CortexA53 processor cores with 32 KB L1-D cache and 32 KB L1-I cache Features summary Eight 32-bit / 64-bit ARM v8 Cortex-A53 CPUs - Arranged as two clusters of four cores sharing a 1 MB L2 cache - Speed Up to 1.5 GHz - Support for cluster power-gating. Cache coherent interconnect (CCI-400) - Hardware-managed data coherency - Up to 700 MHz One 64-bit DDR4 SDRAM memory controller with ECC Data path acceleration architecture 2.0 (DPAA2) Three PCIe 3.0 controllers One serial ATA (SATA 3.0) controller Three high-speed USB 3.0 controllers with integrated PHY Following levels of DTSI/DTS files have been created for the LS1088A SoC family: - fsl-ls1088a.dtsi: DTS-Include file for NXP LS1088A SoC. - fsl-ls1088a-qds.dts: DTS file for NXP LS1088A QDS board. - fsl-ls1088a-rdb.dts: DTS file for NXP LS1088A RDB board Signed-off-by: Harninder Rai Signed-off-by: Ashish Kumar Signed-off-by: Raghav Dogra --- Changes in v2: Incorporated Shawn's comments - License changed to GPL/X11 dual license - Device nodes in dtsi are disabled - Properly named temp-sensor node - Adjusted timer node to just after gic - Miscellaneous minor comments arch/arm64/boot/dts/freescale/Makefile | 2 + arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts | 123 ++++++++++ arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts | 106 +++++++++ arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 275 ++++++++++++++++++++++ 4 files changed, 506 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 6d5df45..72c4b52 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -5,6 +5,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1043a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1046a-rdb.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-qds.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts new file mode 100644 index 0000000..2edab57 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-qds.dts @@ -0,0 +1,123 @@ +/* + * Device Tree file for NXP LS1088A QDS Board. + * + * Copyright 2017 NXP + * + * Harninder Rai + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "fsl-ls1088a.dtsi" + +/ { + model = "LS1088A QDS Board"; + compatible = "fsl,ls1088a-qds", "fsl,ls1088a"; +}; + +&i2c0 { + status = "okay"; + + pca9547 at 77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c at 2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + + ina220 at 40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + + ina220 at 41 { + compatible = "ti,ina220"; + reg = <0x41>; + shunt-resistor = <1000>; + }; + }; + + i2c at 3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + rtc at 51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + /* IRQ10_B */ + interrupts = <0 150 0x4>; + }; + + eeprom at 56 { + compatible = "atmel,24c512"; + reg = <0x56>; + }; + + eeprom at 57 { + compatible = "atmel,24c512"; + reg = <0x57>; + }; + + temp-sensor at 4c { + compatible = "adi,adt7461a"; + reg = <0x4c>; + }; + }; + }; +}; + +&sata0 { + status = "okay"; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts new file mode 100644 index 0000000..6e4cfbb --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts @@ -0,0 +1,106 @@ +/* + * Device Tree file for NXP LS1088A RDB Board. + * + * Copyright 2017 NXP + * + * Harninder Rai + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "fsl-ls1088a.dtsi" + +/ { + model = "L1088A RDB Board"; + compatible = "fsl,ls1088a-rdb", "fsl,ls1088a"; +}; + +&i2c0 { + status = "okay"; + pca9547 at 77 { + compatible = "nxp,pca9547"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>; + + i2c at 2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2>; + + ina220 at 40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <1000>; + }; + }; + + i2c at 3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x3>; + + rtc at 51 { + compatible = "nxp,pcf2129"; + reg = <0x51>; + /* IRQ10_B */ + interrupts = <0 150 0x4>; + }; + + temp-sensor at 4c { + compatible = "adi,adt7461a"; + reg = <0x4c>; + }; + }; + }; +}; + +&sata0 { + status = "okay"; +}; + +&duart0 { + status = "okay"; +}; + +&duart1 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi new file mode 100644 index 0000000..63c0a8e --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi @@ -0,0 +1,275 @@ +/* + * Device Tree Include file for NXP Layerscape-1088A family SoC. + * + * Copyright 2017 NXP + * + * Harninder Rai + * + * This file is dual-licensed: you can use it either under the terms + * of the GPLv2 or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +#include + +/ { + compatible = "fsl,ls1088a"; + interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + /* We have 2 clusters having 4 Cortex-A53 cores each */ + cpu0: cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + clocks = <&clockgen 1 0>; + }; + + cpu1: cpu at 1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + clocks = <&clockgen 1 0>; + }; + + cpu2: cpu at 2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + clocks = <&clockgen 1 0>; + }; + + cpu3: cpu at 3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + clocks = <&clockgen 1 0>; + }; + + cpu4: cpu at 100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x100>; + clocks = <&clockgen 1 1>; + }; + + cpu5: cpu at 101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x101>; + clocks = <&clockgen 1 1>; + }; + + cpu6: cpu at 102 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x102>; + clocks = <&clockgen 1 1>; + }; + + cpu7: cpu at 103 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x103>; + clocks = <&clockgen 1 1>; + }; + }; + + gic: interrupt-controller at 6000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */ + <0x0 0x06100000 0 0x100000>, /* GICR(RD_base+SGI_base)*/ + <0x0 0x0c0c0000 0 0x2000>, /* GICC */ + <0x0 0x0c0d0000 0 0x1000>, /* GICH */ + <0x0 0x0c0e0000 0 0x20000>; /* GICV */ + interrupts = <1 9 0x4>; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <1 13 IRQ_TYPE_LEVEL_LOW>,/* Physical Secure PPI */ + <1 14 IRQ_TYPE_LEVEL_LOW>,/* Physical Non-Secure PPI */ + <1 11 IRQ_TYPE_LEVEL_LOW>,/* Virtual PPI */ + <1 10 IRQ_TYPE_LEVEL_LOW>;/* Hypervisor PPI */ + }; + + sysclk: sysclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "sysclk"; + }; + + soc { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clockgen: clocking at 1300000 { + compatible = "fsl,ls1088a-clockgen"; + reg = <0 0x1300000 0 0xa0000>; + #clock-cells = <2>; + clocks = <&sysclk>; + }; + + duart0: serial at 21c0500 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0500 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + duart1: serial at 21c0600 { + compatible = "fsl,ns16550", "ns16550a"; + reg = <0x0 0x21c0600 0x0 0x100>; + clocks = <&clockgen 4 3>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + gpio0: gpio at 2300000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2300000 0x0 0x10000>; + interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio at 2310000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2310000 0x0 0x10000>; + interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio at 2320000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2320000 0x0 0x10000>; + interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio at 2330000 { + compatible = "fsl,qoriq-gpio"; + reg = <0x0 0x2330000 0x0 0x10000>; + interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + ifc: ifc at 2240000 { + compatible = "fsl,ifc", "simple-bus"; + reg = <0x0 0x2240000 0x0 0x20000>; + interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>; + little-endian; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0x5 0x80000000 0x08000000 + 2 0 0x5 0x30000000 0x00010000 + 3 0 0x5 0x20000000 0x00010000>; + status = "disabled"; + }; + + i2c0: i2c at 2000000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + i2c1: i2c at 2010000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2010000 0x0 0x10000>; + interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + i2c2: i2c at 2020000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2020000 0x0 0x10000>; + interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + i2c3: i2c at 2030000 { + compatible = "fsl,vf610-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x2030000 0x0 0x10000>; + interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + + sata0: sata at 3200000 { + compatible = "fsl,ls1088a-ahci", "fsl,ls1043a-ahci"; + reg = <0x0 0x3200000 0x0 0x10000>; + interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clockgen 4 3>; + status = "disabled"; + }; + }; + +}; -- 2.7.4