From mboxrd@z Thu Jan 1 00:00:00 1970 From: Laurent Hardy Subject: [PATCH v4] net/ixgbe: ensure link status is updated Date: Thu, 27 Apr 2017 17:03:42 +0200 Message-ID: <1493305422-10611-1-git-send-email-laurent.hardy@6wind.com> References: <49759EB36A64CF4892C1AFEC9231E8D650A662DC@PGSMSX101.gar.corp.intel.com> Cc: ferruh.yigit@intel.com, helin.zhang@intel.com, konstantin.ananyev@intel.com, olivier.matz@6wind.com To: dev@dpdk.org, wei.dai@intel.com Return-path: Received: from proxy.6wind.com (host.76.145.23.62.rev.coltfrance.com [62.23.145.76]) by dpdk.org (Postfix) with ESMTP id 043921077 for ; Thu, 27 Apr 2017 17:04:03 +0200 (CEST) In-Reply-To: <49759EB36A64CF4892C1AFEC9231E8D650A662DC@PGSMSX101.gar.corp.intel.com> List-Id: DPDK patches and discussions List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Errors-To: dev-bounces@dpdk.org Sender: "dev" In case of fiber and link speed set to 1Gb at peer side (with autoneg or with defined speed), link status could be not properly updated at time cable is plugged-in. Indeed if cable was not plugged when device has been configured and started then link status will not be updated properly with new speed as no link setup will be triggered. To avoid this issue, IXGBE_FLAG_NEED_LINK_CONFIG is set to try a link setup each time link_update() is triggered and current link status is down. When cable is plugged-in, link setup will be performed via ixgbe_setup_link(). Signed-off-by: Laurent Hardy --- Hi Wei, please find enclosed patch v4, tested using testpmd. v1 -> v2: - rebase on top of head (change flag to 1<<4) - fix regression with copper links: only update link for fiber links v2 -> v3: - remove unnescessary check on speed mask if autoneg is false v3 -> v4: - remove default speed set to 10Gb if autoneg is false, rely on ixgbe_get_link_capabilities( ) instead. --- drivers/net/ixgbe/ixgbe_ethdev.c | 14 ++++++++++++++ drivers/net/ixgbe/ixgbe_ethdev.h | 1 + 2 files changed, 15 insertions(+) diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c index 7b856bb..8a0c0a7 100644 --- a/drivers/net/ixgbe/ixgbe_ethdev.c +++ b/drivers/net/ixgbe/ixgbe_ethdev.c @@ -3782,8 +3782,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete) struct ixgbe_hw *hw = IXGBE_DEV_PRIVATE_TO_HW(dev->data->dev_private); struct rte_eth_link link, old; ixgbe_link_speed link_speed = IXGBE_LINK_SPEED_UNKNOWN; + struct ixgbe_interrupt *intr = + IXGBE_DEV_PRIVATE_TO_INTR(dev->data->dev_private); int link_up; int diag; + u32 speed = 0; + bool autoneg = false; link.link_status = ETH_LINK_DOWN; link.link_speed = 0; @@ -3793,6 +3797,14 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete) hw->mac.get_link_status = true; + if ((intr->flags & IXGBE_FLAG_NEED_LINK_CONFIG) && + hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) { + speed = hw->phy.autoneg_advertised; + if (!speed) + ixgbe_get_link_capabilities(hw, &speed, &autoneg); + ixgbe_setup_link(hw, speed, true); + } + /* check if it needs to wait to complete, if lsc interrupt is enabled */ if (wait_to_complete == 0 || dev->data->dev_conf.intr_conf.lsc != 0) diag = ixgbe_check_link(hw, &link_speed, &link_up, 0); @@ -3810,10 +3822,12 @@ ixgbe_dev_link_update(struct rte_eth_dev *dev, int wait_to_complete) if (link_up == 0) { rte_ixgbe_dev_atomic_write_link_status(dev, &link); + intr->flags |= IXGBE_FLAG_NEED_LINK_CONFIG; if (link.link_status == old.link_status) return -1; return 0; } + intr->flags &= ~IXGBE_FLAG_NEED_LINK_CONFIG; link.link_status = ETH_LINK_UP; link.link_duplex = ETH_LINK_FULL_DUPLEX; diff --git a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h index 5176b02..b576a6f 100644 --- a/drivers/net/ixgbe/ixgbe_ethdev.h +++ b/drivers/net/ixgbe/ixgbe_ethdev.h @@ -45,6 +45,7 @@ #define IXGBE_FLAG_MAILBOX (uint32_t)(1 << 1) #define IXGBE_FLAG_PHY_INTERRUPT (uint32_t)(1 << 2) #define IXGBE_FLAG_MACSEC (uint32_t)(1 << 3) +#define IXGBE_FLAG_NEED_LINK_CONFIG (uint32_t)(1 << 4) /* * Defines that were not part of ixgbe_type.h as they are not used by the -- 2.1.4