* [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo
@ 2017-08-28 6:28 Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd Peng Fan
` (11 more replies)
0 siblings, 12 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Typo fix: CONIFG->CONFIG
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Tom Rini <trini@konsulko.com>
---
V2: none
scripts/Makefile.uncmd_spl | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/scripts/Makefile.uncmd_spl b/scripts/Makefile.uncmd_spl
index 15d0836..b399411 100644
--- a/scripts/Makefile.uncmd_spl
+++ b/scripts/Makefile.uncmd_spl
@@ -9,7 +9,7 @@ ifdef CONFIG_SPL_BUILD
ifndef CONFIG_SPL_DM
CONFIG_DM_SERIAL=
CONFIG_DM_GPIO=
-CONIFG_DM_I2C=
+CONFIG_DM_I2C=
CONFIG_DM_SPI=
CONFIG_DM_SPI_FLASH=
endif
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
@ 2017-08-28 6:28 ` Peng Fan
2017-08-28 6:40 ` Jagan Teki
2017-08-28 6:28 ` [U-Boot] [PATCH V2 03/12] power: pmic/regulator allow dm be omited by SPL Peng Fan
` (10 subsequent siblings)
11 siblings, 1 reply; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: none
arch/arm/dts/Makefile | 3 +
arch/arm/dts/imx6dl-sabresd.dts | 22 ++
arch/arm/dts/imx6dl.dtsi | 242 +++++++++++++
arch/arm/dts/imx6q-sabresd.dts | 30 ++
arch/arm/dts/imx6q.dtsi | 164 ++++++++-
arch/arm/dts/imx6qdl-sabresd.dtsi | 738 ++++++++++++++++++++++++++++++++++++++
arch/arm/dts/imx6qdl.dtsi | 100 ++++--
arch/arm/dts/imx6qp-sabresd.dts | 93 +++++
arch/arm/dts/imx6qp.dtsi | 153 ++++++++
arch/arm/dts/imx6sx-sdb-reva.dts | 143 ++++++++
arch/arm/dts/imx6sx-sdb.dts | 147 ++++++++
arch/arm/dts/imx6sx-sdb.dtsi | 612 +++++++++++++++++++++++++++++++
12 files changed, 2422 insertions(+), 25 deletions(-)
create mode 100644 arch/arm/dts/imx6dl-sabresd.dts
create mode 100644 arch/arm/dts/imx6q-sabresd.dts
create mode 100644 arch/arm/dts/imx6qdl-sabresd.dtsi
create mode 100644 arch/arm/dts/imx6qp-sabresd.dts
create mode 100644 arch/arm/dts/imx6qp.dtsi
create mode 100644 arch/arm/dts/imx6sx-sdb-reva.dts
create mode 100644 arch/arm/dts/imx6sx-sdb.dts
create mode 100644 arch/arm/dts/imx6sx-sdb.dtsi
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 762429c..242e4f1 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -357,7 +357,10 @@ dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \
imx6sll-evk.dtb \
imx6dl-icore.dtb \
imx6dl-icore-rqs.dtb \
+ imx6dl-sabresd.dtb \
imx6q-cm-fx6.dtb \
+ imx6q-sabresd.dtb \
+ imx6qp-sabresd.dtb \
imx6q-icore.dtb \
imx6q-icore-rqs.dtb \
imx6q-logicpd.dtb \
diff --git a/arch/arm/dts/imx6dl-sabresd.dts b/arch/arm/dts/imx6dl-sabresd.dts
new file mode 100644
index 0000000..9607afe
--- /dev/null
+++ b/arch/arm/dts/imx6dl-sabresd.dts
@@ -0,0 +1,22 @@
+/*
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-sabresd.dtsi"
+
+/ {
+ model = "Freescale i.MX6 DualLite SABRE Smart Device Board";
+ compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl";
+};
+
+&ipu1_csi1_from_ipu1_csi1_mux {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+};
diff --git a/arch/arm/dts/imx6dl.dtsi b/arch/arm/dts/imx6dl.dtsi
index 9a4c22c..8475e6c 100644
--- a/arch/arm/dts/imx6dl.dtsi
+++ b/arch/arm/dts/imx6dl.dtsi
@@ -100,6 +100,11 @@
};
};
+ capture-subsystem {
+ compatible = "fsl,imx-capture-subsystem";
+ ports = <&ipu1_csi0>, <&ipu1_csi1>;
+ };
+
display-subsystem {
compatible = "fsl,imx-display-subsystem";
ports = <&ipu1_di0>, <&ipu1_di1>;
@@ -111,6 +116,169 @@
};
};
+&gpio1 {
+ gpio-ranges = <&iomuxc 0 131 2>, <&iomuxc 2 137 8>, <&iomuxc 10 189 2>,
+ <&iomuxc 12 194 1>, <&iomuxc 13 193 1>, <&iomuxc 14 192 1>,
+ <&iomuxc 15 191 1>, <&iomuxc 16 185 2>, <&iomuxc 18 184 1>,
+ <&iomuxc 19 187 1>, <&iomuxc 20 183 1>, <&iomuxc 21 188 1>,
+ <&iomuxc 22 123 3>, <&iomuxc 25 121 1>, <&iomuxc 26 127 1>,
+ <&iomuxc 27 126 1>, <&iomuxc 28 128 1>, <&iomuxc 29 130 1>,
+ <&iomuxc 30 129 1>, <&iomuxc 31 122 1>;
+};
+
+&gpio2 {
+ gpio-ranges = <&iomuxc 0 161 8>, <&iomuxc 8 208 8>, <&iomuxc 16 74 1>,
+ <&iomuxc 17 73 1>, <&iomuxc 18 72 1>, <&iomuxc 19 71 1>,
+ <&iomuxc 20 70 1>, <&iomuxc 21 69 1>, <&iomuxc 22 68 1>,
+ <&iomuxc 23 79 2>, <&iomuxc 25 118 2>, <&iomuxc 27 117 1>,
+ <&iomuxc 28 113 4>;
+};
+
+&gpio3 {
+ gpio-ranges = <&iomuxc 0 97 2>, <&iomuxc 2 105 8>, <&iomuxc 10 99 6>,
+ <&iomuxc 16 81 16>;
+};
+
+&gpio4 {
+ gpio-ranges = <&iomuxc 5 136 1>, <&iomuxc 6 145 1>, <&iomuxc 7 150 1>,
+ <&iomuxc 8 146 1>, <&iomuxc 9 151 1>, <&iomuxc 10 147 1>,
+ <&iomuxc 11 152 1>, <&iomuxc 12 148 1>, <&iomuxc 13 153 1>,
+ <&iomuxc 14 149 1>, <&iomuxc 15 154 1>, <&iomuxc 16 39 7>,
+ <&iomuxc 23 56 1>, <&iomuxc 24 61 7>, <&iomuxc 31 46 1>;
+};
+
+&gpio5 {
+ gpio-ranges = <&iomuxc 0 120 1>, <&iomuxc 2 77 1>, <&iomuxc 4 76 1>,
+ <&iomuxc 5 47 9>, <&iomuxc 14 57 4>, <&iomuxc 18 37 1>,
+ <&iomuxc 19 36 1>, <&iomuxc 20 35 1>, <&iomuxc 21 38 1>,
+ <&iomuxc 22 29 6>, <&iomuxc 28 19 4>;
+};
+
+&gpio6 {
+ gpio-ranges = <&iomuxc 0 23 6>, <&iomuxc 6 75 1>, <&iomuxc 7 156 1>,
+ <&iomuxc 8 155 1>, <&iomuxc 9 170 1>, <&iomuxc 10 169 1>,
+ <&iomuxc 11 157 1>, <&iomuxc 14 158 3>, <&iomuxc 17 204 1>,
+ <&iomuxc 18 203 1>, <&iomuxc 19 182 1>, <&iomuxc 20 177 4>,
+ <&iomuxc 24 175 1>, <&iomuxc 25 171 1>, <&iomuxc 26 181 1>,
+ <&iomuxc 27 172 3>, <&iomuxc 30 176 1>, <&iomuxc 31 78 1>;
+};
+
+&gpio7 {
+ gpio-ranges = <&iomuxc 0 202 1>, <&iomuxc 1 201 1>, <&iomuxc 2 196 1>,
+ <&iomuxc 3 195 1>, <&iomuxc 4 197 4>, <&iomuxc 8 205 1>,
+ <&iomuxc 9 207 1>, <&iomuxc 10 206 1>, <&iomuxc 11 133 3>;
+};
+
+&gpr {
+ ipu1_csi0_mux: ipu1_csi0_mux at 34 {
+ compatible = "video-mux";
+ mux-controls = <&mux 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ ipu1_csi0_mux_from_mipi_vc0: endpoint {
+ remote-endpoint = <&mipi_vc0_to_ipu1_csi0_mux>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ ipu1_csi0_mux_from_mipi_vc1: endpoint {
+ remote-endpoint = <&mipi_vc1_to_ipu1_csi0_mux>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ ipu1_csi0_mux_from_mipi_vc2: endpoint {
+ remote-endpoint = <&mipi_vc2_to_ipu1_csi0_mux>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ ipu1_csi0_mux_from_mipi_vc3: endpoint {
+ remote-endpoint = <&mipi_vc3_to_ipu1_csi0_mux>;
+ };
+ };
+
+ port at 4 {
+ reg = <4>;
+
+ ipu1_csi0_mux_from_parallel_sensor: endpoint {
+ };
+ };
+
+ port at 5 {
+ reg = <5>;
+
+ ipu1_csi0_mux_to_ipu1_csi0: endpoint {
+ remote-endpoint = <&ipu1_csi0_from_ipu1_csi0_mux>;
+ };
+ };
+ };
+
+ ipu1_csi1_mux: ipu1_csi1_mux at 34 {
+ compatible = "video-mux";
+ mux-controls = <&mux 1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ ipu1_csi1_mux_from_mipi_vc0: endpoint {
+ remote-endpoint = <&mipi_vc0_to_ipu1_csi1_mux>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ ipu1_csi1_mux_from_mipi_vc1: endpoint {
+ remote-endpoint = <&mipi_vc1_to_ipu1_csi1_mux>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ ipu1_csi1_mux_from_mipi_vc2: endpoint {
+ remote-endpoint = <&mipi_vc2_to_ipu1_csi1_mux>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ ipu1_csi1_mux_from_mipi_vc3: endpoint {
+ remote-endpoint = <&mipi_vc3_to_ipu1_csi1_mux>;
+ };
+ };
+
+ port at 4 {
+ reg = <4>;
+
+ ipu1_csi1_mux_from_parallel_sensor: endpoint {
+ };
+ };
+
+ port at 5 {
+ reg = <5>;
+
+ ipu1_csi1_mux_to_ipu1_csi1: endpoint {
+ remote-endpoint = <&ipu1_csi1_from_ipu1_csi1_mux>;
+ };
+ };
+ };
+};
+
&gpt {
compatible = "fsl,imx6dl-gpt";
};
@@ -119,6 +287,12 @@
compatible = "fsl,imx6dl-hdmi";
};
+&ipu1_csi1 {
+ ipu1_csi1_from_ipu1_csi1_mux: endpoint {
+ remote-endpoint = <&ipu1_csi1_mux_to_ipu1_csi1>;
+ };
+};
+
&ldb {
clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
<&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
@@ -128,6 +302,74 @@
"di0", "di1";
};
+&mipi_csi {
+ port at 1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mipi_vc0_to_ipu1_csi0_mux: endpoint at 0 {
+ remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>;
+ };
+
+ mipi_vc0_to_ipu1_csi1_mux: endpoint at 1 {
+ remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc0>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mipi_vc1_to_ipu1_csi0_mux: endpoint at 0 {
+ remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc1>;
+ };
+
+ mipi_vc1_to_ipu1_csi1_mux: endpoint at 1 {
+ remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc1>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mipi_vc2_to_ipu1_csi0_mux: endpoint at 0 {
+ remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc2>;
+ };
+
+ mipi_vc2_to_ipu1_csi1_mux: endpoint at 1 {
+ remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc2>;
+ };
+ };
+
+ port at 4 {
+ reg = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mipi_vc3_to_ipu1_csi0_mux: endpoint at 0 {
+ remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc3>;
+ };
+
+ mipi_vc3_to_ipu1_csi1_mux: endpoint at 1 {
+ remote-endpoint = <&ipu1_csi1_mux_from_mipi_vc3>;
+ };
+ };
+};
+
+&mux {
+ mux-reg-masks = <0x34 0x00000007>, /* IPU_CSI0_MUX */
+ <0x34 0x00000038>, /* IPU_CSI1_MUX */
+ <0x0c 0x0000000c>, /* HDMI_MUX_CTL */
+ <0x0c 0x000000c0>, /* LVDS0_MUX_CTL */
+ <0x0c 0x00000300>, /* LVDS1_MUX_CTL */
+ <0x28 0x00000003>, /* DCIC1_MUX_CTL */
+ <0x28 0x0000000c>; /* DCIC2_MUX_CTL */
+};
+
&vpu {
compatible = "fsl,imx6dl-vpu", "cnm,coda960";
};
diff --git a/arch/arm/dts/imx6q-sabresd.dts b/arch/arm/dts/imx6q-sabresd.dts
new file mode 100644
index 0000000..527772b
--- /dev/null
+++ b/arch/arm/dts/imx6q-sabresd.dts
@@ -0,0 +1,30 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-sabresd.dtsi"
+
+/ {
+ model = "Freescale i.MX6 Quad SABRE Smart Device Board";
+ compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
+};
+
+&sata {
+ status = "okay";
+};
+
+&ipu1_csi1_from_mipi_vc1 {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+};
diff --git a/arch/arm/dts/imx6q.dtsi b/arch/arm/dts/imx6q.dtsi
index c30c836..90a74173 100644
--- a/arch/arm/dts/imx6q.dtsi
+++ b/arch/arm/dts/imx6q.dtsi
@@ -125,7 +125,7 @@
clocks = <&clks IMX6QDL_CLK_OPENVG_AXI>,
<&clks IMX6QDL_CLK_GPU2D_CORE>;
clock-names = "bus", "core";
- power-domains = <&gpc 1>;
+ power-domains = <&pd_pu>;
};
ipu2: ipu at 02800000 {
@@ -143,10 +143,18 @@
ipu2_csi0: port at 0 {
reg = <0>;
+
+ ipu2_csi0_from_mipi_vc2: endpoint {
+ remote-endpoint = <&mipi_vc2_to_ipu2_csi0>;
+ };
};
ipu2_csi1: port at 1 {
reg = <1>;
+
+ ipu2_csi1_from_ipu2_csi1_mux: endpoint {
+ remote-endpoint = <&ipu2_csi1_mux_to_ipu2_csi1>;
+ };
};
ipu2_di0: port at 2 {
@@ -198,6 +206,11 @@
};
};
+ capture-subsystem {
+ compatible = "fsl,imx-capture-subsystem";
+ ports = <&ipu1_csi0>, <&ipu1_csi1>, <&ipu2_csi0>, <&ipu2_csi1>;
+ };
+
display-subsystem {
compatible = "fsl,imx-display-subsystem";
ports = <&ipu1_di0>, <&ipu1_di1>, <&ipu2_di0>, <&ipu2_di1>;
@@ -209,6 +222,105 @@
};
};
+&gpio1 {
+ gpio-ranges = <&iomuxc 0 136 2>, <&iomuxc 2 141 1>, <&iomuxc 3 139 1>,
+ <&iomuxc 4 142 2>, <&iomuxc 6 140 1>, <&iomuxc 7 144 2>,
+ <&iomuxc 9 138 1>, <&iomuxc 10 213 3>, <&iomuxc 13 20 1>,
+ <&iomuxc 14 19 1>, <&iomuxc 15 21 1>, <&iomuxc 16 208 1>,
+ <&iomuxc 17 207 1>, <&iomuxc 18 210 3>, <&iomuxc 21 209 1>,
+ <&iomuxc 22 116 10>;
+};
+
+&gpio2 {
+ gpio-ranges = <&iomuxc 0 191 16>, <&iomuxc 16 55 14>, <&iomuxc 30 35 1>,
+ <&iomuxc 31 44 1>;
+};
+
+&gpio3 {
+ gpio-ranges = <&iomuxc 0 69 16>, <&iomuxc 16 36 8>, <&iomuxc 24 45 8>;
+};
+
+&gpio4 {
+ gpio-ranges = <&iomuxc 5 149 1>, <&iomuxc 6 126 10>, <&iomuxc 16 87 16>;
+};
+
+&gpio5 {
+ gpio-ranges = <&iomuxc 0 85 1>, <&iomuxc 2 34 1>, <&iomuxc 4 53 1>,
+ <&iomuxc 5 103 13>, <&iomuxc 18 150 14>;
+};
+
+&gpio6 {
+ gpio-ranges = <&iomuxc 0 164 6>, <&iomuxc 6 54 1>, <&iomuxc 7 181 5>,
+ <&iomuxc 14 186 3>, <&iomuxc 17 170 2>, <&iomuxc 19 22 12>,
+ <&iomuxc 31 86 1>;
+};
+
+&gpio7 {
+ gpio-ranges = <&iomuxc 0 172 9>, <&iomuxc 9 189 2>, <&iomuxc 11 146 3>;
+};
+
+&gpr {
+ ipu1_csi0_mux {
+ compatible = "video-mux";
+ mux-controls = <&mux 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ ipu1_csi0_mux_from_mipi_vc0: endpoint {
+ remote-endpoint = <&mipi_vc0_to_ipu1_csi0_mux>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ ipu1_csi0_mux_from_parallel_sensor: endpoint {
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ ipu1_csi0_mux_to_ipu1_csi0: endpoint {
+ remote-endpoint = <&ipu1_csi0_from_ipu1_csi0_mux>;
+ };
+ };
+ };
+
+ ipu2_csi1_mux {
+ compatible = "video-mux";
+ mux-controls = <&mux 1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+
+ ipu2_csi1_mux_from_mipi_vc3: endpoint {
+ remote-endpoint = <&mipi_vc3_to_ipu2_csi1_mux>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+
+ ipu2_csi1_mux_from_parallel_sensor: endpoint {
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ ipu2_csi1_mux_to_ipu2_csi1: endpoint {
+ remote-endpoint = <&ipu2_csi1_from_ipu2_csi1_mux>;
+ };
+ };
+ };
+};
+
&hdmi {
compatible = "fsl,imx6q-hdmi";
@@ -229,6 +341,12 @@
};
};
+&ipu1_csi1 {
+ ipu1_csi1_from_mipi_vc1: endpoint {
+ remote-endpoint = <&mipi_vc1_to_ipu1_csi1>;
+ };
+};
+
&ldb {
clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
<&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
@@ -275,6 +393,40 @@
};
};
+&mipi_csi {
+ port at 1 {
+ reg = <1>;
+
+ mipi_vc0_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_mipi_vc0>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+
+ mipi_vc1_to_ipu1_csi1: endpoint {
+ remote-endpoint = <&ipu1_csi1_from_mipi_vc1>;
+ };
+ };
+
+ port at 3 {
+ reg = <3>;
+
+ mipi_vc2_to_ipu2_csi0: endpoint {
+ remote-endpoint = <&ipu2_csi0_from_mipi_vc2>;
+ };
+ };
+
+ port at 4 {
+ reg = <4>;
+
+ mipi_vc3_to_ipu2_csi1_mux: endpoint {
+ remote-endpoint = <&ipu2_csi1_mux_from_mipi_vc3>;
+ };
+ };
+};
+
&mipi_dsi {
ports {
port at 2 {
@@ -295,6 +447,16 @@
};
};
+&mux {
+ mux-reg-masks = <0x04 0x00080000>, /* MIPI_IPU1_MUX */
+ <0x04 0x00100000>, /* MIPI_IPU2_MUX */
+ <0x0c 0x0000000c>, /* HDMI_MUX_CTL */
+ <0x0c 0x000000c0>, /* LVDS0_MUX_CTL */
+ <0x0c 0x00000300>, /* LVDS1_MUX_CTL */
+ <0x28 0x00000003>, /* DCIC1_MUX_CTL */
+ <0x28 0x0000000c>; /* DCIC2_MUX_CTL */
+};
+
&vpu {
compatible = "fsl,imx6q-vpu", "cnm,coda960";
};
diff --git a/arch/arm/dts/imx6qdl-sabresd.dtsi b/arch/arm/dts/imx6qdl-sabresd.dtsi
new file mode 100644
index 0000000..b72b6fa
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-sabresd.dtsi
@@ -0,0 +1,738 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usb_otg_vbus: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 0>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
+
+ reg_usb_h1_vbus: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 29 0>;
+ enable-active-high;
+ vin-supply = <&swbst_reg>;
+ };
+
+ reg_audio: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "wm8962-supply";
+ gpio = <&gpio4 10 0>;
+ enable-active-high;
+ };
+
+ reg_pcie: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_reg>;
+ regulator-name = "MPCIE_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 19 0>;
+ regulator-always-on;
+ enable-active-high;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ linux,code = <KEY_POWER>;
+ };
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "Volume Down";
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx6q-sabresd-wm8962",
+ "fsl,imx-audio-wm8962";
+ model = "wm8962-audio";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "Ext Spk", "SPKOUTL",
+ "Ext Spk", "SPKOUTR",
+ "AMIC", "MICBIAS",
+ "IN3R", "AMIC";
+ mux-int-port = <2>;
+ mux-ext-port = <3>;
+ };
+
+ backlight_lvds: backlight-lvds {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ red {
+ gpios = <&gpio1 2 0>;
+ default-state = "on";
+ };
+ };
+
+ panel {
+ compatible = "hannstar,hsd100pxn1";
+ backlight = <&backlight_lvds>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+ data-shift = <12>; /* Lines 19:12 used */
+ hsync-active = <1>;
+ vsync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
+&mipi_csi {
+ status = "okay";
+
+ port at 0 {
+ reg = <0>;
+
+ mipi_csi2_in: endpoint {
+ remote-endpoint = <&ov5640_to_mipi_csi2>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 9 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash: m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p32", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ codec: wm8962 at 1a {
+ compatible = "wlf,wm8962";
+ reg = <0x1a>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ DCVDD-supply = <®_audio>;
+ DBVDD-supply = <®_audio>;
+ AVDD-supply = <®_audio>;
+ CPVDD-supply = <®_audio>;
+ MICVDD-supply = <®_audio>;
+ PLLVDD-supply = <®_audio>;
+ SPKVDD1-supply = <®_audio>;
+ SPKVDD2-supply = <®_audio>;
+ gpio-cfg = <
+ 0x0000 /* 0:Default */
+ 0x0000 /* 1:Default */
+ 0x0013 /* 2:FN_DMICCLK */
+ 0x0000 /* 3:Default */
+ 0x8014 /* 4:FN_DMICCDAT */
+ 0x0000 /* 5:Default */
+ >;
+ };
+
+ ov5642: camera at 3c {
+ compatible = "ovti,ov5642";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5642>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ reg = <0x3c>;
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v, rev C board is VGEN3
+ rev B board is VGEN5 */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v*/
+ powerdown-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+
+ port {
+ ov5642_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ ov5640: camera at 3c {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clks IMX6QDL_CLK_CKO>;
+ clock-names = "xclk";
+ DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+ AVDD-supply = <&vgen3_reg>; /* 2.8v, rev C board is VGEN3
+ rev B board is VGEN5 */
+ DVDD-supply = <&vgen2_reg>; /* 1.5v*/
+ powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ov5640_to_mipi_csi2: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ };
+ };
+ };
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ egalax_ts at 04 {
+ compatible = "eeti,egalax_ts";
+ reg = <0x04>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <7 2>;
+ wakeup-gpios = <&gpio6 7 0>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ imx6qdl-sabresd {
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+ MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+ MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+ MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+ MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0
+ MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ >;
+ };
+
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
+ >;
+ };
+
+ pinctrl_ov5640: ov5640grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+ MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_ov5642: ov5642grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+ MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_pcie_reg: pciereggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x17059
+ MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x17059
+ MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x17059
+ MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
+ >;
+ };
+ };
+
+ gpio_leds {
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel at 1 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <18>;
+ status = "okay";
+
+ port at 4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+®_arm {
+ vin-supply = <&sw1a_reg>;
+};
+
+®_pu {
+ vin-supply = <&sw1c_reg>;
+};
+
+®_soc {
+ vin-supply = <&sw1c_reg>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ no-1-8-v;
+ status = "okay";
+};
+
+&wdog1 {
+ status = "disabled";
+};
+
+&wdog2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
diff --git a/arch/arm/dts/imx6qdl.dtsi b/arch/arm/dts/imx6qdl.dtsi
index b13b0b2..a9723b9 100644
--- a/arch/arm/dts/imx6qdl.dtsi
+++ b/arch/arm/dts/imx6qdl.dtsi
@@ -13,9 +13,18 @@
#include <dt-bindings/clock/imx6qdl-clock.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include "skeleton.dtsi"
-
/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /*
+ * The decompressor and also some bootloaders rely on a
+ * pre-existing /chosen node to be available to insert the
+ * command line and merge other ATAGS info.
+ * Also for U-Boot there must be a pre-existing /memory node.
+ */
+ chosen {};
+ memory { device_type = "memory"; reg = <0 0>; };
+
aliases {
ethernet0 = &fec;
can0 = &can1;
@@ -147,7 +156,7 @@
<&clks IMX6QDL_CLK_GPU3D_CORE>,
<&clks IMX6QDL_CLK_GPU3D_SHADER>;
clock-names = "bus", "core", "shader";
- power-domains = <&gpc 1>;
+ power-domains = <&pd_pu>;
};
gpu_2d: gpu at 00134000 {
@@ -157,7 +166,7 @@
clocks = <&clks IMX6QDL_CLK_GPU2D_AXI>,
<&clks IMX6QDL_CLK_GPU2D_CORE>;
clock-names = "bus", "core";
- power-domains = <&gpc 1>;
+ power-domains = <&pd_pu>;
};
timer at 00a00600 {
@@ -188,7 +197,7 @@
arm,shared-override;
};
- pcie: pcie at 0x01000000 {
+ pcie: pcie at 1ffc000 {
compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
reg = <0x01ffc000 0x04000>,
<0x01f00000 0x80000>;
@@ -196,6 +205,7 @@
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ bus-range = <0x00 0xff>;
ranges = <0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */
num-lanes = <1>;
@@ -204,9 +214,9 @@
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
- <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+ <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
<&clks IMX6QDL_CLK_LVDS1_GATE>,
<&clks IMX6QDL_CLK_PCIE_REF_125M>;
@@ -424,7 +434,7 @@
clocks = <&clks IMX6QDL_CLK_VPU_AXI>,
<&clks IMX6QDL_CLK_MMDC_CH0_AXI>;
clock-names = "per", "ahb";
- power-domains = <&gpc 1>;
+ power-domains = <&pd_pu>;
resets = <&src 1>;
iram = <&ocram>;
};
@@ -625,8 +635,8 @@
regulator-1p1 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd1p1";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1375000>;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1200000>;
regulator-always-on;
anatop-reg-offset = <0x110>;
anatop-vol-bit-shift = <8>;
@@ -634,6 +644,7 @@
anatop-min-bit-val = <4>;
anatop-min-voltage = <800000>;
anatop-max-voltage = <1375000>;
+ anatop-enable-bit = <0>;
};
regulator-3p0 {
@@ -648,20 +659,22 @@
anatop-min-bit-val = <0>;
anatop-min-voltage = <2625000>;
anatop-max-voltage = <3400000>;
+ anatop-enable-bit = <0>;
};
regulator-2p5 {
compatible = "fsl,anatop-regulator";
regulator-name = "vdd2p5";
- regulator-min-microvolt = <2000000>;
+ regulator-min-microvolt = <2250000>;
regulator-max-microvolt = <2750000>;
regulator-always-on;
anatop-reg-offset = <0x130>;
anatop-vol-bit-shift = <8>;
anatop-vol-bit-width = <5>;
anatop-min-bit-val = <0>;
- anatop-min-voltage = <2000000>;
- anatop-max-voltage = <2750000>;
+ anatop-min-voltage = <2100000>;
+ anatop-max-voltage = <2875000>;
+ anatop-enable-bit = <0>;
};
reg_arm: regulator-vddcore {
@@ -787,19 +800,39 @@
interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
<0 90 IRQ_TYPE_LEVEL_HIGH>;
interrupt-parent = <&intc>;
- pu-supply = <®_pu>;
- clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>,
- <&clks IMX6QDL_CLK_GPU3D_SHADER>,
- <&clks IMX6QDL_CLK_GPU2D_CORE>,
- <&clks IMX6QDL_CLK_GPU2D_AXI>,
- <&clks IMX6QDL_CLK_OPENVG_AXI>,
- <&clks IMX6QDL_CLK_VPU_AXI>;
- #power-domain-cells = <1>;
+ clocks = <&clks IMX6QDL_CLK_IPG>;
+ clock-names = "ipg";
+
+ pgc {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-domain at 0 {
+ reg = <0>;
+ #power-domain-cells = <0>;
+ };
+ pd_pu: power-domain at 1 {
+ reg = <1>;
+ #power-domain-cells = <0>;
+ power-supply = <®_pu>;
+ clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>,
+ <&clks IMX6QDL_CLK_GPU3D_SHADER>,
+ <&clks IMX6QDL_CLK_GPU2D_CORE>,
+ <&clks IMX6QDL_CLK_GPU2D_AXI>,
+ <&clks IMX6QDL_CLK_OPENVG_AXI>,
+ <&clks IMX6QDL_CLK_VPU_AXI>;
+ };
+ };
};
gpr: iomuxc-gpr at 020e0000 {
- compatible = "fsl,imx6q-iomuxc-gpr", "syscon";
+ compatible = "fsl,imx6q-iomuxc-gpr", "syscon", "simple-mfd";
reg = <0x020e0000 0x38>;
+
+ mux: mux-controller {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ };
};
iomuxc: iomuxc at 020e0000 {
@@ -807,7 +840,7 @@
reg = <0x020e0000 0x4000>;
};
- ldb: ldb at 020e0008 {
+ ldb: ldb {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,imx6q-ldb", "fsl,imx53-ldb";
@@ -1092,10 +1125,14 @@
};
weim: weim at 021b8000 {
+ #address-cells = <2>;
+ #size-cells = <1>;
compatible = "fsl,imx6q-weim";
reg = <0x021b8000 0x4000>;
interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks IMX6QDL_CLK_EIM_SLOW>;
+ fsl,weim-cs-gpr = <&gpr>;
+ status = "disabled";
};
ocotp: ocotp at 021bc000 {
@@ -1121,7 +1158,16 @@
};
mipi_csi: mipi at 021dc000 {
+ compatible = "fsl,imx6-mipi-csi2";
reg = <0x021dc000 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 100 0x04>, <0 101 0x04>;
+ clocks = <&clks IMX6QDL_CLK_HSI_TX>,
+ <&clks IMX6QDL_CLK_VIDEO_27M>,
+ <&clks IMX6QDL_CLK_EIM_PODF>;
+ clock-names = "dphy", "ref", "pix";
+ status = "disabled";
};
mipi_dsi: mipi at 021e0000 {
@@ -1153,8 +1199,10 @@
};
vdoa at 021e4000 {
+ compatible = "fsl,imx6q-vdoa";
reg = <0x021e4000 0x4000>;
interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_VDOA>;
};
uart2: serial at 021e8000 {
@@ -1221,6 +1269,10 @@
ipu1_csi0: port at 0 {
reg = <0>;
+
+ ipu1_csi0_from_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_to_ipu1_csi0>;
+ };
};
ipu1_csi1: port at 1 {
diff --git a/arch/arm/dts/imx6qp-sabresd.dts b/arch/arm/dts/imx6qp-sabresd.dts
new file mode 100644
index 0000000..a8a5004
--- /dev/null
+++ b/arch/arm/dts/imx6qp-sabresd.dts
@@ -0,0 +1,93 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6qdl-sabresd.dtsi"
+
+/ {
+ model = "Freescale i.MX6 Quad Plus SABRE Smart Device Board";
+ compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp";
+};
+
+®_arm {
+ vin-supply = <&sw2_reg>;
+};
+
+&iomuxc {
+ imx6qdl-sabresd {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10071
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x17059
+ MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x17059
+ MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x17059
+ MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10071
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ >;
+ };
+ };
+};
+
+&pcie {
+ status = "disabled";
+};
diff --git a/arch/arm/dts/imx6qp.dtsi b/arch/arm/dts/imx6qp.dtsi
new file mode 100644
index 0000000..299d863
--- /dev/null
+++ b/arch/arm/dts/imx6qp.dtsi
@@ -0,0 +1,153 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6q.dtsi"
+
+/ {
+ soc {
+ ocram2: sram at 00940000 {
+ compatible = "mmio-sram";
+ reg = <0x00940000 0x20000>;
+ clocks = <&clks IMX6QDL_CLK_OCRAM>;
+ };
+
+ ocram3: sram at 00960000 {
+ compatible = "mmio-sram";
+ reg = <0x00960000 0x20000>;
+ clocks = <&clks IMX6QDL_CLK_OCRAM>;
+ };
+
+ aips-bus at 02100000 {
+ pre1: pre at 21c8000 {
+ compatible = "fsl,imx6qp-pre";
+ reg = <0x021c8000 0x1000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clks IMX6QDL_CLK_PRE0>;
+ clock-names = "axi";
+ fsl,iram = <&ocram2>;
+ };
+
+ pre2: pre at 21c9000 {
+ compatible = "fsl,imx6qp-pre";
+ reg = <0x021c9000 0x1000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clks IMX6QDL_CLK_PRE1>;
+ clock-names = "axi";
+ fsl,iram = <&ocram2>;
+ };
+
+ pre3: pre at 21ca000 {
+ compatible = "fsl,imx6qp-pre";
+ reg = <0x021ca000 0x1000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clks IMX6QDL_CLK_PRE2>;
+ clock-names = "axi";
+ fsl,iram = <&ocram3>;
+ };
+
+ pre4: pre at 21cb000 {
+ compatible = "fsl,imx6qp-pre";
+ reg = <0x021cb000 0x1000>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clks IMX6QDL_CLK_PRE3>;
+ clock-names = "axi";
+ fsl,iram = <&ocram3>;
+ };
+
+ prg1: prg at 21cc000 {
+ compatible = "fsl,imx6qp-prg";
+ reg = <0x021cc000 0x1000>;
+ clocks = <&clks IMX6QDL_CLK_PRG0_APB>,
+ <&clks IMX6QDL_CLK_PRG0_AXI>;
+ clock-names = "ipg", "axi";
+ fsl,pres = <&pre1>, <&pre2>, <&pre3>;
+ };
+
+ prg2: prg at 21cd000 {
+ compatible = "fsl,imx6qp-prg";
+ reg = <0x021cd000 0x1000>;
+ clocks = <&clks IMX6QDL_CLK_PRG1_APB>,
+ <&clks IMX6QDL_CLK_PRG1_AXI>;
+ clock-names = "ipg", "axi";
+ fsl,pres = <&pre4>, <&pre2>, <&pre3>;
+ };
+ };
+ };
+};
+
+&fec {
+ /delete-property/interrupts-extended;
+ interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>,
+ <0 119 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&gpc {
+ compatible = "fsl,imx6qp-gpc", "fsl,imx6q-gpc";
+};
+
+&ipu1 {
+ compatible = "fsl,imx6qp-ipu", "fsl,imx6q-ipu";
+ fsl,prg = <&prg1>;
+};
+
+&ipu2 {
+ compatible = "fsl,imx6qp-ipu", "fsl,imx6q-ipu";
+ fsl,prg = <&prg2>;
+};
+
+&ldb {
+ clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_LDB_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU1_DI0_SEL>, <&clks IMX6QDL_CLK_IPU1_DI1_SEL>,
+ <&clks IMX6QDL_CLK_IPU2_DI0_SEL>, <&clks IMX6QDL_CLK_IPU2_DI1_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI0_PODF>, <&clks IMX6QDL_CLK_LDB_DI1_PODF>;
+ clock-names = "di0_pll", "di1_pll",
+ "di0_sel", "di1_sel", "di2_sel", "di3_sel",
+ "di0", "di1";
+};
+
+&mmdc0 {
+ compatible = "fsl,imx6qp-mmdc", "fsl,imx6q-mmdc";
+};
+
+&pcie {
+ compatible = "fsl,imx6qp-pcie", "snps,dw-pcie";
+};
diff --git a/arch/arm/dts/imx6sx-sdb-reva.dts b/arch/arm/dts/imx6sx-sdb-reva.dts
new file mode 100644
index 0000000..7100547
--- /dev/null
+++ b/arch/arm/dts/imx6sx-sdb-reva.dts
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "imx6sx-sdb.dtsi"
+
+/ {
+ model = "Freescale i.MX6 SoloX SDB RevA Board";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&qspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi2>;
+ status = "okay";
+
+ flash0: s25fl128s at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25fl128s", "jedec,spi-nor";
+ spi-max-frequency = <66000000>;
+ };
+
+ flash1: s25fl128s at 1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25fl128s", "jedec,spi-nor";
+ spi-max-frequency = <66000000>;
+ };
+};
diff --git a/arch/arm/dts/imx6sx-sdb.dts b/arch/arm/dts/imx6sx-sdb.dts
new file mode 100644
index 0000000..5bb8fd5
--- /dev/null
+++ b/arch/arm/dts/imx6sx-sdb.dts
@@ -0,0 +1,147 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "imx6sx-sdb.dtsi"
+
+/ {
+ model = "Freescale i.MX6 SoloX SDB RevB Board";
+};
+
+&cpu0 {
+ operating-points = <
+ /* kHz uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+ fsl,soc-operating-points = <
+ /* ARM kHz SOC uV */
+ 996000 1250000
+ 792000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze200";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&qspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi2>;
+ status = "okay";
+
+ flash0: n25q256a at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a", "jedec,spi-nor";
+ spi-max-frequency = <29000000>;
+ reg = <0>;
+ };
+
+ flash1: n25q256a at 1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a", "jedec,spi-nor";
+ spi-max-frequency = <29000000>;
+ reg = <1>;
+ };
+};
diff --git a/arch/arm/dts/imx6sx-sdb.dtsi b/arch/arm/dts/imx6sx-sdb.dtsi
new file mode 100644
index 0000000..da81552
--- /dev/null
+++ b/arch/arm/dts/imx6sx-sdb.dtsi
@@ -0,0 +1,612 @@
+/*
+ * Copyright (C) 2014 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+ model = "Freescale i.MX6 SoloX SDB Board";
+ compatible = "fsl,imx6sx-sdb", "fsl,imx6sx";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x40000000>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm3 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ volume-up {
+ label = "Volume Up";
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ volume-down {
+ label = "Volume Down";
+ gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vcc_sd3: regulator at 0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_vcc_sd3>;
+ regulator-name = "VCC_SD3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg1_vbus: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg2>;
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_psu_5v: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "PSU-5V0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_lcd_3v3: regulator at 4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "lcd-3v3";
+ gpio = <&gpio3 27 0>;
+ enable-active-high;
+ };
+
+ reg_peri_3v3: regulator at 5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_peri_3v3>;
+ regulator-name = "peri_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_enet_3v3: regulator at 6 {
+ compatible = "regulator-fixed";
+ reg = <6>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet_3v3>;
+ regulator-name = "enet_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
+ model = "wm8962-audio";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&codec>;
+ audio-routing =
+ "Headphone Jack", "HPOUTL",
+ "Headphone Jack", "HPOUTR",
+ "Ext Spk", "SPKOUTL",
+ "Ext Spk", "SPKOUTR",
+ "AMIC", "MICBIAS",
+ "IN3R", "AMIC";
+ mux-int-port = <2>;
+ mux-ext-port = <6>;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-supply = <®_enet_3v3>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+
+ ethphy2: ethernet-phy at 2 {
+ reg = <2>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ codec: wm8962 at 1a {
+ compatible = "wlf,wm8962";
+ reg = <0x1a>;
+ clocks = <&clks IMX6SX_CLK_AUDIO>;
+ DCVDD-supply = <&vgen4_reg>;
+ DBVDD-supply = <&vgen4_reg>;
+ AVDD-supply = <&vgen4_reg>;
+ CPVDD-supply = <&vgen4_reg>;
+ MICVDD-supply = <&vgen3_reg>;
+ PLLVDD-supply = <&vgen4_reg>;
+ SPKVDD1-supply = <®_psu_5v>;
+ SPKVDD2-supply = <®_psu_5v>;
+ };
+};
+
+&lcdif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd>;
+ lcd-supply = <®_lcd_3v3>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <89>;
+ hfront-porch = <164>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ hsync-len = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&sai1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ status = "disabled";
+};
+
+&ssi2 {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart5 { /* for bluetooth */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1_id>;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ cd-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <&vcc_sd3>;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ cd-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ imx6x-sdb {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6SX_PAD_CSI_DATA00__AUDMUX_AUD6_TXC 0x130b0
+ MX6SX_PAD_CSI_DATA01__AUDMUX_AUD6_TXFS 0x130b0
+ MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD 0x120b0
+ MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD 0x130b0
+ MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK 0x130b0
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0b1
+ MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0b1
+ MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC 0xa0b1
+ MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0b1
+ MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0b1
+ MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 0xa0b1
+ MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 0xa0b1
+ MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0b1
+ MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK 0x3081
+ MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x3081
+ MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081
+ MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081
+ MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
+ MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
+ MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91
+ >;
+ };
+
+ pinctrl_enet_3v3: enet3v3grp {
+ fsl,pins = <
+ MX6SX_PAD_ENET2_COL__GPIO2_IO_6 0x80000000
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1
+ MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1
+ MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1
+ MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081
+ MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081
+ MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio_keysgrp {
+ fsl,pins = <
+ MX6SX_PAD_CSI_DATA04__GPIO1_IO_18 0x17059
+ MX6SX_PAD_CSI_DATA05__GPIO1_IO_19 0x17059
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1
+ MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6SX_PAD_KEY_ROW4__I2C3_SDA 0x4001b8b1
+ MX6SX_PAD_KEY_COL4__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6SX_PAD_CSI_DATA07__I2C4_SDA 0x4001b8b1
+ MX6SX_PAD_CSI_DATA06__I2C4_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_lcd: lcdgrp {
+ fsl,pins = <
+ MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22 0x4001b0b0
+ MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23 0x4001b0b0
+ MX6SX_PAD_LCD1_CLK__LCDIF1_CLK 0x4001b0b0
+ MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE 0x4001b0b0
+ MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC 0x4001b0b0
+ MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC 0x4001b0b0
+ MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 0x4001b0b0
+ >;
+ };
+
+ pinctrl_peri_3v3: peri3v3grp {
+ fsl,pins = <
+ MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16 0x80000000
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp-1 {
+ fsl,pins = <
+ MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_qspi2: qspi2grp {
+ fsl,pins = <
+ MX6SX_PAD_NAND_WP_B__QSPI2_A_DATA_0 0x70f1
+ MX6SX_PAD_NAND_READY_B__QSPI2_A_DATA_1 0x70f1
+ MX6SX_PAD_NAND_CE0_B__QSPI2_A_DATA_2 0x70f1
+ MX6SX_PAD_NAND_CE1_B__QSPI2_A_DATA_3 0x70f1
+ MX6SX_PAD_NAND_CLE__QSPI2_A_SCLK 0x70f1
+ MX6SX_PAD_NAND_ALE__QSPI2_A_SS0_B 0x70f1
+ MX6SX_PAD_NAND_DATA01__QSPI2_B_DATA_0 0x70f1
+ MX6SX_PAD_NAND_DATA00__QSPI2_B_DATA_1 0x70f1
+ MX6SX_PAD_NAND_WE_B__QSPI2_B_DATA_2 0x70f1
+ MX6SX_PAD_NAND_RE_B__QSPI2_B_DATA_3 0x70f1
+ MX6SX_PAD_NAND_DATA02__QSPI2_B_SCLK 0x70f1
+ MX6SX_PAD_NAND_DATA03__QSPI2_B_SS0_B 0x70f1
+ >;
+ };
+
+ pinctrl_vcc_sd3: vccsd3grp {
+ fsl,pins = <
+ MX6SX_PAD_KEY_COL1__GPIO2_IO_11 0x17059
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ MX6SX_PAD_CSI_DATA00__SAI1_TX_BCLK 0x130b0
+ MX6SX_PAD_CSI_DATA01__SAI1_TX_SYNC 0x130b0
+ MX6SX_PAD_CSI_HSYNC__SAI1_TX_DATA_0 0x120b0
+ MX6SX_PAD_CSI_VSYNC__SAI1_RX_DATA_0 0x130b0
+ MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK 0x130b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO04__UART1_TX 0x1b0b1
+ MX6SX_PAD_GPIO1_IO05__UART1_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6SX_PAD_KEY_ROW3__UART5_RX 0x1b0b1
+ MX6SX_PAD_KEY_COL3__UART5_TX 0x1b0b1
+ MX6SX_PAD_KEY_ROW2__UART5_CTS_B 0x1b0b1
+ MX6SX_PAD_KEY_COL2__UART5_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0
+ >;
+ };
+
+ pinctrl_usb_otg1_id: usbotg1idgrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_usb_otg2: usbot2ggrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO12__GPIO1_IO_12 0x10b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059
+ MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059
+ MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059
+ MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059
+ MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059
+ MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x17059
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x10059
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x17059
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x17059
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x17059
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x17059
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x17059
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x17059
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x17059
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x17059
+ MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x17059 /* CD */
+ MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x17059 /* WP */
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170b9
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100b9
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170b9
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170b9
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170b9
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170b9
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170b9
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170b9
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170b9
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+ fsl,pins = <
+ MX6SX_PAD_SD3_CMD__USDHC3_CMD 0x170f9
+ MX6SX_PAD_SD3_CLK__USDHC3_CLK 0x100f9
+ MX6SX_PAD_SD3_DATA0__USDHC3_DATA0 0x170f9
+ MX6SX_PAD_SD3_DATA1__USDHC3_DATA1 0x170f9
+ MX6SX_PAD_SD3_DATA2__USDHC3_DATA2 0x170f9
+ MX6SX_PAD_SD3_DATA3__USDHC3_DATA3 0x170f9
+ MX6SX_PAD_SD3_DATA4__USDHC3_DATA4 0x170f9
+ MX6SX_PAD_SD3_DATA5__USDHC3_DATA5 0x170f9
+ MX6SX_PAD_SD3_DATA6__USDHC3_DATA6 0x170f9
+ MX6SX_PAD_SD3_DATA7__USDHC3_DATA7 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059
+ MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059
+ MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059
+ MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059
+ MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059
+ MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059
+ MX6SX_PAD_SD4_DATA7__GPIO6_IO_21 0x17059 /* CD */
+ MX6SX_PAD_SD4_DATA6__GPIO6_IO_20 0x17059 /* WP */
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6SX_PAD_GPIO1_IO13__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+ };
+};
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 03/12] power: pmic/regulator allow dm be omited by SPL
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd Peng Fan
@ 2017-08-28 6:28 ` Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 04/12] Makefile: build FIT image if CONFIG_SPL_FIT_GENERATOR defined Peng Fan
` (9 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Allow the dm driver be omited by SPL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Jacob Chen <jacob-chen@iotwrt.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: add r-b tag
drivers/power/pmic/Makefile | 4 ++--
drivers/power/regulator/Makefile | 2 +-
2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile
index f7bdfa5..4abdaf6 100644
--- a/drivers/power/pmic/Makefile
+++ b/drivers/power/pmic/Makefile
@@ -5,10 +5,10 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_DM_PMIC) += pmic-uclass.o
+obj-$(CONFIG_$(SPL_)DM_PMIC) += pmic-uclass.o
obj-$(CONFIG_DM_PMIC_MAX77686) += max77686.o
obj-$(CONFIG_DM_PMIC_MAX8998) += max8998.o
-obj-$(CONFIG_DM_PMIC_PFUZE100) += pfuze100.o
+obj-$(CONFIG_$(SPL_)DM_PMIC_PFUZE100) += pfuze100.o
obj-$(CONFIG_PMIC_S2MPS11) += s2mps11.o
obj-$(CONFIG_DM_PMIC_SANDBOX) += sandbox.o i2c_pmic_emul.o
obj-$(CONFIG_PMIC_ACT8846) += act8846.o
diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
index 18fb870..ec1b1e0 100644
--- a/drivers/power/regulator/Makefile
+++ b/drivers/power/regulator/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_$(SPL_)DM_REGULATOR) += regulator-uclass.o
obj-$(CONFIG_REGULATOR_ACT8846) += act8846.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722_regulator.o
obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
-obj-$(CONFIG_DM_REGULATOR_PFUZE100) += pfuze100.o
+obj-$(CONFIG_$(SPL_)DM_REGULATOR_PFUZE100) += pfuze100.o
obj-$(CONFIG_REGULATOR_PWM) += pwm_regulator.o
obj-$(CONFIG_$(SPL_)DM_REGULATOR_FIXED) += fixed.o
obj-$(CONFIG_$(SPL_)DM_REGULATOR_GPIO) += gpio-regulator.o
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 04/12] Makefile: build FIT image if CONFIG_SPL_FIT_GENERATOR defined
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 03/12] power: pmic/regulator allow dm be omited by SPL Peng Fan
@ 2017-08-28 6:28 ` Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 05/12] imx: introduce mkimage_fit.sh Peng Fan
` (8 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Build FIT image if CONFIG_SPL_FIT_GENERATOR defined.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: "Cooper Jr., Franklin" <fcooper@ti.com>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: none
Makefile | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Makefile b/Makefile
index a0f3bfd..a1d7394 100644
--- a/Makefile
+++ b/Makefile
@@ -805,6 +805,10 @@ ALL-y += u-boot-tegra.bin u-boot-nodtb-tegra.bin
ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb-tegra.bin
endif
+ifneq ($(CONFIG_SPL_FIT_GENERATOR),)
+ALL-y += u-boot.itb
+endif
+
# Add optional build target if defined in board/cpu/soc headers
ifneq ($(CONFIG_BUILD_TARGET),)
ALL-y += $(CONFIG_BUILD_TARGET:"%"=%)
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 05/12] imx: introduce mkimage_fit.sh
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (2 preceding siblings ...)
2017-08-28 6:28 ` [U-Boot] [PATCH V2 04/12] Makefile: build FIT image if CONFIG_SPL_FIT_GENERATOR defined Peng Fan
@ 2017-08-28 6:28 ` Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 06/12] imx: mx6sabresd: implement board_fit_config_name_match Peng Fan
` (7 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Introduce mkimage_fit.sh which is modifed from
board/sunxi/mksunxi_fit_atf.sh.
ATF is dropped and modified for arm32 arch.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
---
V2: none
arch/arm/mach-imx/mkimage_fit.sh | 63 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 63 insertions(+)
create mode 100755 arch/arm/mach-imx/mkimage_fit.sh
diff --git a/arch/arm/mach-imx/mkimage_fit.sh b/arch/arm/mach-imx/mkimage_fit.sh
new file mode 100755
index 0000000..18628de
--- /dev/null
+++ b/arch/arm/mach-imx/mkimage_fit.sh
@@ -0,0 +1,63 @@
+#!/bin/sh
+#
+# script to generate FIT image source for 32-bit imx boards with
+# multiple device trees (given on the command line)
+#
+# usage: $0 <dt_name> [<dt_name> [<dt_name] ...]
+
+cat << __HEADER_EOF
+/dts-v1/;
+
+/ {
+ description = "Configuration to load ATF before U-Boot";
+ #address-cells = <1>;
+
+ images {
+ uboot at 1 {
+ description = "U-Boot (32-bit)";
+ data = /incbin/("u-boot-nodtb.bin");
+ type = "standalone";
+ arch = "arm32";
+ compression = "none";
+ load = <0x17800000>;
+ };
+__HEADER_EOF
+
+cnt=1
+for dtname in $*
+do
+ cat << __FDT_IMAGE_EOF
+ fdt@$cnt {
+ description = "$(basename $dtname .dtb)";
+ data = /incbin/("$dtname");
+ type = "flat_dt";
+ compression = "none";
+ };
+__FDT_IMAGE_EOF
+ cnt=$((cnt+1))
+done
+
+cat << __CONF_HEADER_EOF
+ };
+ configurations {
+ default = "config at 1";
+
+__CONF_HEADER_EOF
+
+cnt=1
+for dtname in $*
+do
+ cat << __CONF_SECTION_EOF
+ config@$cnt {
+ description = "$(basename $dtname .dtb)";
+ firmware = "uboot@1";
+ fdt = "fdt@$cnt";
+ };
+__CONF_SECTION_EOF
+ cnt=$((cnt+1))
+done
+
+cat << __ITS_EOF
+ };
+};
+__ITS_EOF
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 06/12] imx: mx6sabresd: implement board_fit_config_name_match
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (3 preceding siblings ...)
2017-08-28 6:28 ` [U-Boot] [PATCH V2 05/12] imx: introduce mkimage_fit.sh Peng Fan
@ 2017-08-28 6:28 ` Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 07/12] imx: mx6sabresd: enable SPL FIT Peng Fan
` (6 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Implement board_fit_config_name_match.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
---
V2: none
board/freescale/mx6sabresd/mx6sabresd.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 9a562b3..fa75ab0 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -734,6 +734,19 @@ int spl_start_uboot(void)
}
#endif
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+ if (is_mx6dq() && !strcmp(name, "imx6q-sabresd"))
+ return 0;
+ else if (is_mx6sdl() && !strcmp(name, "imx6dl-sabresd"))
+ return 0;
+ else if (is_mx6dqp() && !strcmp(name, "imx6qp-sabresd"))
+ return 0;
+ return -EINVAL;
+}
+#endif
+
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 07/12] imx: mx6sabresd: enable SPL FIT
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (4 preceding siblings ...)
2017-08-28 6:28 ` [U-Boot] [PATCH V2 06/12] imx: mx6sabresd: implement board_fit_config_name_match Peng Fan
@ 2017-08-28 6:28 ` Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 08/12] mmc: fsl_esdhc: switch to use CONFIG_IS_ENABLED Peng Fan
` (5 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:28 UTC (permalink / raw)
To: u-boot
Enable SPL FIT. Now DM drivers are not enabled, so boards boot as before
with only the difference that loading dtb.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
---
V2: none
configs/mx6sabresd_defconfig | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/configs/mx6sabresd_defconfig b/configs/mx6sabresd_defconfig
index 7949c5e..7491e9c 100644
--- a/configs/mx6sabresd_defconfig
+++ b/configs/mx6sabresd_defconfig
@@ -9,6 +9,10 @@ CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_WATCHDOG_SUPPORT=y
CONFIG_VIDEO=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-sabresd"
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit.sh"
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6QDL"
CONFIG_ENV_IS_IN_MMC=y
CONFIG_BOOTDELAY=3
@@ -41,6 +45,8 @@ CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_LIST="imx6q-sabresd imx6dl-sabresd imx6qp-sabresd"
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
@@ -54,4 +60,3 @@ CONFIG_G_DNL_MANUFACTURER="FSL"
CONFIG_G_DNL_VENDOR_NUM=0x0525
CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 08/12] mmc: fsl_esdhc: switch to use CONFIG_IS_ENABLED
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (5 preceding siblings ...)
2017-08-28 6:28 ` [U-Boot] [PATCH V2 07/12] imx: mx6sabresd: enable SPL FIT Peng Fan
@ 2017-08-28 6:29 ` Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 09/12] power: pmic.h: include dm/ofnode.h Peng Fan
` (4 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:29 UTC (permalink / raw)
To: u-boot
Switch to use CONFIG_IS_ENABLED.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: none
drivers/mmc/fsl_esdhc.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index cc188c4..aa02bd6 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -113,7 +113,7 @@ struct fsl_esdhc_priv {
int non_removable;
int wp_enable;
int vs18_enable;
-#ifdef CONFIG_DM_GPIO
+#if CONFIG_IS_ENABLED(DM_GPIO)
struct gpio_desc cd_gpio;
struct gpio_desc wp_gpio;
#endif
@@ -695,7 +695,7 @@ static int esdhc_getcd_common(struct fsl_esdhc_priv *priv)
#if CONFIG_IS_ENABLED(DM_MMC)
if (priv->non_removable)
return 1;
-#ifdef CONFIG_DM_GPIO
+#if CONFIG_IS_ENABLED(DM_GPIO)
if (dm_gpio_is_valid(&priv->cd_gpio))
return dm_gpio_get_value(&priv->cd_gpio);
#endif
@@ -1048,7 +1048,7 @@ static int fsl_esdhc_probe(struct udevice *dev)
priv->non_removable = 1;
} else {
priv->non_removable = 0;
-#ifdef CONFIG_DM_GPIO
+#if CONFIG_IS_ENABLED(DM_GPIO)
gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
GPIOD_IS_IN);
#endif
@@ -1056,7 +1056,7 @@ static int fsl_esdhc_probe(struct udevice *dev)
priv->wp_enable = 1;
-#ifdef CONFIG_DM_GPIO
+#if CONFIG_IS_ENABLED(DM_GPIO)
ret = gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio,
GPIOD_IS_IN);
if (ret)
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 09/12] power: pmic.h: include dm/ofnode.h
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (6 preceding siblings ...)
2017-08-28 6:29 ` [U-Boot] [PATCH V2 08/12] mmc: fsl_esdhc: switch to use CONFIG_IS_ENABLED Peng Fan
@ 2017-08-28 6:29 ` Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 10/12] board: freescale: common: add pfuze dm code Peng Fan
` (3 subsequent siblings)
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:29 UTC (permalink / raw)
To: u-boot
Include dm/ofnode.h.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: add r-b tag
include/power/pmic.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/power/pmic.h b/include/power/pmic.h
index 4b34316..e2517f2 100644
--- a/include/power/pmic.h
+++ b/include/power/pmic.h
@@ -12,6 +12,7 @@
#define __CORE_PMIC_H_
#include <i2c.h>
+#include <dm/ofnode.h>
#include <linux/list.h>
#include <power/power_chrg.h>
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 10/12] board: freescale: common: add pfuze dm code
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (7 preceding siblings ...)
2017-08-28 6:29 ` [U-Boot] [PATCH V2 09/12] power: pmic.h: include dm/ofnode.h Peng Fan
@ 2017-08-28 6:29 ` Peng Fan
2017-08-28 16:26 ` York Sun
2017-08-28 6:29 ` [U-Boot] [PATCH V2 11/12] imx: mx6sabresd: enable dm drivers Peng Fan
` (2 subsequent siblings)
11 siblings, 1 reply; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:29 UTC (permalink / raw)
To: u-boot
Add pfuze dm code, this code does the same thing as pfuze.c, but
only effects when CONFIG_$(SPL_)DM_PMIC_PFUZE100 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: none
board/freescale/common/Makefile | 1 +
board/freescale/common/pfuze.h | 5 +++
board/freescale/common/pfuze_dm.c | 89 +++++++++++++++++++++++++++++++++++++++
3 files changed, 95 insertions(+)
create mode 100644 board/freescale/common/pfuze_dm.c
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 1c53fb6..620dced 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_VSC_CROSSBAR) += vsc3316_3308.o
obj-$(CONFIG_IDT8T49N222A) += idt8t49n222a_serdes_clk.o
obj-$(CONFIG_ZM7300) += zm7300.o
obj-$(CONFIG_POWER_PFUZE100) += pfuze.o
+obj-$(CONFIG_$(SPL_)DM_PMIC_PFUZE100) += pfuze_dm.o
obj-$(CONFIG_POWER_MC34VR500) += mc34vr500.o
obj-$(CONFIG_LS102XA_STREAM_ID) += ls102xa_stream_id.o
diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h
index 53cfc99..9c4c92a 100644
--- a/board/freescale/common/pfuze.h
+++ b/board/freescale/common/pfuze.h
@@ -7,7 +7,12 @@
#ifndef __PFUZE_BOARD_HELPER__
#define __PFUZE_BOARD_HELPER__
+#if CONFIG_IS_ENABLED(DM_PMIC_PFUZE100)
+struct udevice *pfuze_common_init(void);
+int pfuze_mode_init(struct udevice *dev, u32 mode);
+#else
struct pmic *pfuze_common_init(unsigned char i2cbus);
int pfuze_mode_init(struct pmic *p, u32 mode);
+#endif
#endif
diff --git a/board/freescale/common/pfuze_dm.c b/board/freescale/common/pfuze_dm.c
new file mode 100644
index 0000000..c6af627
--- /dev/null
+++ b/board/freescale/common/pfuze_dm.c
@@ -0,0 +1,89 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+
+int pfuze_mode_init(struct udevice *dev, u32 mode)
+{
+ unsigned char offset, i, switch_num;
+ u32 id;
+ int ret;
+
+ id = pmic_reg_read(dev, PFUZE100_DEVICEID);
+ id = id & 0xf;
+
+ if (id == 0) {
+ switch_num = 6;
+ offset = PFUZE100_SW1CMODE;
+ } else if (id == 1) {
+ switch_num = 4;
+ offset = PFUZE100_SW2MODE;
+ } else {
+ printf("Not supported, id=%d\n", id);
+ return -EINVAL;
+ }
+
+ ret = pmic_reg_write(dev, PFUZE100_SW1ABMODE, mode);
+ if (ret < 0) {
+ printf("Set SW1AB mode error!\n");
+ return ret;
+ }
+
+ for (i = 0; i < switch_num - 1; i++) {
+ ret = pmic_reg_write(dev, offset + i * SWITCH_SIZE, mode);
+ if (ret < 0) {
+ printf("Set switch 0x%x mode error!\n",
+ offset + i * SWITCH_SIZE);
+ return ret;
+ }
+ }
+
+ return ret;
+}
+
+struct udevice *pfuze_common_init(void)
+{
+ struct udevice *dev;
+ int ret;
+ unsigned int reg, dev_id, rev_id;
+
+ ret = pmic_get("pfuze100", &dev);
+ if (ret == -ENODEV)
+ return NULL;
+
+ dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
+ rev_id = pmic_reg_read(dev, PFUZE100_REVID);
+ printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+ /* Set SW1AB stanby volage to 0.975V */
+ reg = pmic_reg_read(dev, PFUZE100_SW1ABSTBY);
+ reg &= ~SW1x_STBY_MASK;
+ reg |= SW1x_0_975V;
+ pmic_reg_write(dev, PFUZE100_SW1ABSTBY, reg);
+
+ /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+ reg = pmic_reg_read(dev, PFUZE100_SW1ABCONF);
+ reg &= ~SW1xCONF_DVSSPEED_MASK;
+ reg |= SW1xCONF_DVSSPEED_4US;
+ pmic_reg_write(dev, PFUZE100_SW1ABCONF, reg);
+
+ /* Set SW1C standby voltage to 0.975V */
+ reg = pmic_reg_read(dev, PFUZE100_SW1CSTBY);
+ reg &= ~SW1x_STBY_MASK;
+ reg |= SW1x_0_975V;
+ pmic_reg_write(dev, PFUZE100_SW1CSTBY, reg);
+
+ /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
+ reg = pmic_reg_read(dev, PFUZE100_SW1CCONF);
+ reg &= ~SW1xCONF_DVSSPEED_MASK;
+ reg |= SW1xCONF_DVSSPEED_4US;
+ pmic_reg_write(dev, PFUZE100_SW1CCONF, reg);
+
+ return dev;
+}
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 11/12] imx: mx6sabresd: enable dm drivers
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (8 preceding siblings ...)
2017-08-28 6:29 ` [U-Boot] [PATCH V2 10/12] board: freescale: common: add pfuze dm code Peng Fan
@ 2017-08-28 6:29 ` Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 12/12] imx: mx6sabresd: update README Peng Fan
2017-08-28 7:32 ` [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Stefano Babic
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:29 UTC (permalink / raw)
To: u-boot
Enable DM MMC/I2C/PMIC/GPIO/REGULATOR.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: none
board/freescale/mx6sabresd/mx6sabresd.c | 326 +++++++++++++-------------------
configs/mx6sabresd_defconfig | 15 ++
include/configs/mx6sabresd.h | 15 +-
3 files changed, 146 insertions(+), 210 deletions(-)
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index fa75ab0..2123a9d 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -12,7 +12,6 @@
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/video.h>
@@ -24,7 +23,6 @@
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
-#include <i2c.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"
@@ -46,14 +44,6 @@ DECLARE_GLOBAL_DATA_PTR;
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PMIC 1
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
#define DISP0_PWR_EN IMX_GPIO_NR(1, 21)
#define KEY_VOL_UP IMX_GPIO_NR(1, 4)
@@ -93,6 +83,7 @@ static void setup_iomux_enet(void)
{
SETUP_IOMUX_PADS(enet_pads);
+ gpio_request(IMX_GPIO_NR(1, 25), "phy_rst");
/* Reset AR8031 PHY */
gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
mdelay(10);
@@ -100,47 +91,6 @@ static void setup_iomux_enet(void)
udelay(100);
}
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-
static iomux_v3_cfg_t const ecspi1_pads[] = {
IOMUX_PADS(PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
IOMUX_PADS(PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
@@ -187,6 +137,7 @@ static iomux_v3_cfg_t const bl_pads[] = {
static void enable_backlight(void)
{
SETUP_IOMUX_PADS(bl_pads);
+ gpio_request(DISP0_PWR_EN, "disp0_pwr_en");
gpio_direction_output(DISP0_PWR_EN, 1);
}
@@ -201,32 +152,6 @@ static void enable_lvds(struct display_info_t const *dev)
enable_backlight();
}
-static struct i2c_pads_info mx6q_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
static void setup_spi(void)
{
SETUP_IOMUX_PADS(ecspi1_pads);
@@ -253,121 +178,11 @@ static void setup_iomux_uart(void)
SETUP_IOMUX_PADS(uart1_pads);
}
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC2_BASE_ADDR},
- {USDHC3_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
-#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
-
int board_mmc_get_env_dev(int devno)
{
return devno - 1;
}
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = !gpio_get_value(USDHC3_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-#ifndef CONFIG_SPL_BUILD
- int ret;
- int i;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 SD2
- * mmc1 SD3
- * mmc2 eMMC
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- SETUP_IOMUX_PADS(usdhc2_pads);
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 1:
- SETUP_IOMUX_PADS(usdhc3_pads);
- gpio_direction_input(USDHC3_CD_GPIO);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- case 2:
- SETUP_IOMUX_PADS(usdhc4_pads);
- usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
-
- return 0;
-#else
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned reg = readl(&psrc->sbmr1) >> 11;
- /*
- * Upon reading BOOT_CFG register the following map is done:
- * Bit 11 and 12 of BOOT_CFG register can determine the current
- * mmc port
- * 0x1 SD1
- * 0x2 SD2
- * 0x3 SD4
- */
-
- switch (reg & 0x3) {
- case 0x1:
- SETUP_IOMUX_PADS(usdhc2_pads);
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- case 0x2:
- SETUP_IOMUX_PADS(usdhc3_pads);
- usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- case 0x3:
- SETUP_IOMUX_PADS(usdhc4_pads);
- usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- }
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
-}
-#endif
-
static int ar8031_phy_fixup(struct phy_device *phydev)
{
unsigned short val;
@@ -580,6 +395,8 @@ static void setup_usb(void)
imx_iomux_set_gpr_register(1, 13, 1, 0);
SETUP_IOMUX_PADS(usb_hc1_pads);
+
+ gpio_request(IMX_GPIO_NR(1, 29), "usb1");
}
int board_ehci_hcd_init(int port)
@@ -632,13 +449,13 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ gpio_request(IMX_GPIO_NR(3, 19), "pcie_power");
+ gpio_request(IMX_GPIO_NR(7, 12), "pcie_reset");
+
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
- else
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
+
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
@@ -646,34 +463,36 @@ int board_init(void)
return 0;
}
+#ifndef CONFIG_SPL_BUILD
int power_init_board(void)
{
- struct pmic *p;
+ struct udevice *dev;
unsigned int reg;
int ret;
- p = pfuze_common_init(I2C_PMIC);
- if (!p)
+ dev = pfuze_common_init();
+ if (!dev)
return -ENODEV;
- ret = pfuze_mode_init(p, APS_PFM);
+ ret = pfuze_mode_init(dev, APS_PFM);
if (ret < 0)
return ret;
/* Increase VGEN3 from 2.5 to 2.8V */
- pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
+ reg = pmic_reg_read(dev, PFUZE100_VGEN3VOL);
reg &= ~LDO_VOL_MASK;
reg |= LDOB_2_80V;
- pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
+ pmic_reg_write(dev, PFUZE100_VGEN3VOL, reg);
/* Increase VGEN5 from 2.8 to 3V */
- pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
+ reg = pmic_reg_read(dev, PFUZE100_VGEN5VOL);
reg &= ~LDO_VOL_MASK;
reg |= LDOB_3_00V;
- pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
+ pmic_reg_write(dev, PFUZE100_VGEN5VOL, reg);
return 0;
}
+#endif
#ifdef CONFIG_MXC_SPI
int board_spi_cs_gpio(unsigned bus, unsigned cs)
@@ -747,6 +566,115 @@ int board_fit_config_name_match(const char *name)
}
#endif
+#ifdef CONFIG_FSL_ESDHC
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+ IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+};
+
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC2_BASE_ADDR},
+ {USDHC3_BASE_ADDR},
+ {USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ case USDHC4_BASE_ADDR:
+ ret = 1; /* eMMC/uSDHC4 is always present */
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ struct src *psrc = (struct src *)SRC_BASE_ADDR;
+ unsigned reg = readl(&psrc->sbmr1) >> 11;
+ /*
+ * Upon reading BOOT_CFG register the following map is done:
+ * Bit 11 and 12 of BOOT_CFG register can determine the current
+ * mmc port
+ * 0x1 SD1
+ * 0x2 SD2
+ * 0x3 SD4
+ */
+
+ switch (reg & 0x3) {
+ case 0x1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ break;
+ case 0x2:
+ SETUP_IOMUX_PADS(usdhc3_pads);
+ usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ break;
+ case 0x3:
+ SETUP_IOMUX_PADS(usdhc4_pads);
+ usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ break;
+ }
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+#endif
+
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
diff --git a/configs/mx6sabresd_defconfig b/configs/mx6sabresd_defconfig
index 7491e9c..3eab67e 100644
--- a/configs/mx6sabresd_defconfig
+++ b/configs/mx6sabresd_defconfig
@@ -40,6 +40,8 @@ CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
@@ -47,10 +49,23 @@ CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
CONFIG_OF_LIST="imx6q-sabresd imx6dl-sabresd imx6qp-sabresd"
+# CONFIG_BLK is not set
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+# CONFIG_DM_MMC_OPS is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PCI=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index 5410881..a945641 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -43,20 +43,9 @@
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(3, 19)
#endif
-/* I2C Configs */
-#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-
/* USB Configs */
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
@@ -67,4 +56,8 @@
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Enabled USB controller number */
#endif
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_SYS_I2C_MXC
+#endif
+
#endif /* __MX6SABRESD_CONFIG_H */
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 12/12] imx: mx6sabresd: update README
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (9 preceding siblings ...)
2017-08-28 6:29 ` [U-Boot] [PATCH V2 11/12] imx: mx6sabresd: enable dm drivers Peng Fan
@ 2017-08-28 6:29 ` Peng Fan
2017-08-28 7:32 ` [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Stefano Babic
11 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:29 UTC (permalink / raw)
To: u-boot
Update README since we use FIT now.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
---
V2: none
board/freescale/mx6sabresd/README | 18 +++++++++---------
1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a/board/freescale/mx6sabresd/README b/board/freescale/mx6sabresd/README
index 4b4df06..8b10fe7 100644
--- a/board/freescale/mx6sabresd/README
+++ b/board/freescale/mx6sabresd/README
@@ -21,15 +21,15 @@ $ make mx6sabresd_defconfig
$ make
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot.itb binaries.
- Flash the SPL binary into the SD card:
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-- Flash the u-boot.img binary into the SD card:
+- Flash the u-boot.itb binary into the SD card:
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot.itb of=/dev/sdX bs=1K seek=69 && sync
2. Booting from eMMC
@@ -39,7 +39,7 @@ $ make mx6sabresd_defconfig
$ make
-This will generate the SPL and u-boot.img binaries.
+This will generate the SPL and u-boot.itb binaries.
- Boot first from SD card as shown in the previous section
@@ -51,10 +51,10 @@ Mount the eMMC in the host PC:
=> ums 0 mmc 2
-- Flash SPL and u-boot.img binaries into the eMMC:
+- Flash SPL and u-boot.itb binaries into the eMMC:
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot.itb of=/dev/sdX bs=1K seek=69 && sync
Set SW6 to eMMC 8-bit boot: 11010110
@@ -65,15 +65,15 @@ Set SW6 to eMMC 8-bit boot: 11010110
$ make mx6sabresd_defconfig
$ make
-This will generate the SPL image called SPL and the u-boot.img.
+This will generate the SPL image called SPL and the u-boot.itb.
- Flash the SPL image into the SD card:
$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync
-- Flash the u-boot.img image into the SD card:
+- Flash the u-boot.itb image into the SD card:
-$ sudo dd if=u-boot.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
+$ sudo dd if=u-boot.itb of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
Create a partition for root file system and extract it there:
--
2.6.2
^ permalink raw reply related [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 6:28 ` [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd Peng Fan
@ 2017-08-28 6:40 ` Jagan Teki
2017-08-28 6:45 ` Peng Fan
0 siblings, 1 reply; 23+ messages in thread
From: Jagan Teki @ 2017-08-28 6:40 UTC (permalink / raw)
To: u-boot
On Mon, Aug 28, 2017 at 11:58 AM, Peng Fan <peng.fan@nxp.com> wrote:
> Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd board.
>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
Similar series[1] with DTB support for sabresd
[1] https://lists.denx.de/pipermail/u-boot/2017-May/293206.html
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 6:40 ` Jagan Teki
@ 2017-08-28 6:45 ` Peng Fan
2017-08-28 7:06 ` Stefano Babic
0 siblings, 1 reply; 23+ messages in thread
From: Peng Fan @ 2017-08-28 6:45 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Jagan Teki [mailto:jagannadh.teki at gmail.com]
> Sent: Monday, August 28, 2017 2:41 PM
> To: Peng Fan <peng.fan@nxp.com>
> Cc: Stefano Babic <sbabic@denx.de>; u-boot at lists.denx.de
> Subject: Re: [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
>
> On Mon, Aug 28, 2017 at 11:58 AM, Peng Fan <peng.fan@nxp.com> wrote:
> > Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd board.
> >
> > Signed-off-by: Peng Fan <peng.fan@nxp.com>
> > Cc: Stefano Babic <sbabic@denx.de>
> > ---
>
> Similar series[1] with DTB support for sabresd
>
>
> [1] https://lists.denx.de/pipermail/u-boot/2017-May/293206.html
I thought that thread was not active, since past 3 months. I'll leave Stefano to decide.
Regards,
Peng.
>
> thanks!
> --
> Jagan Teki
> Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream
> Maintainer Hyderabad, India.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 6:45 ` Peng Fan
@ 2017-08-28 7:06 ` Stefano Babic
2017-08-28 7:17 ` Peng Fan
` (2 more replies)
0 siblings, 3 replies; 23+ messages in thread
From: Stefano Babic @ 2017-08-28 7:06 UTC (permalink / raw)
To: u-boot
Hi Jagan, Peng, Fabio,
On 28/08/2017 08:45, Peng Fan wrote:
>
>
>> -----Original Message-----
>> From: Jagan Teki [mailto:jagannadh.teki at gmail.com]
>> Sent: Monday, August 28, 2017 2:41 PM
>> To: Peng Fan <peng.fan@nxp.com>
>> Cc: Stefano Babic <sbabic@denx.de>; u-boot at lists.denx.de
>> Subject: Re: [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
>>
>> On Mon, Aug 28, 2017 at 11:58 AM, Peng Fan <peng.fan@nxp.com> wrote:
>>> Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd board.
>>>
>>> Signed-off-by: Peng Fan <peng.fan@nxp.com>
>>> Cc: Stefano Babic <sbabic@denx.de>
>>> ---
>>
>> Similar series[1] with DTB support for sabresd
>>
>>
>> [1] https://lists.denx.de/pipermail/u-boot/2017-May/293206.html
>
> I thought that thread was not active, since past 3 months. I'll leave Stefano to decide.
>
In my understanding, Jagan's series has still open coments from Joe
regarding phy-reset. I have not seen a new post, and I confess I have
then forgotten this series. I have not seen a review by Fabio, too, and
he's the maintainer for sabre boards.
Peng, I have just tried to build with your series, but it breaks many
boards due to DTC issue. I have also tried to build with last DTC from
git, but it does not help. Is it known to you ?
Best regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 7:06 ` Stefano Babic
@ 2017-08-28 7:17 ` Peng Fan
2017-08-28 7:20 ` Jagan Teki
2017-08-28 11:14 ` Fabio Estevam
2 siblings, 0 replies; 23+ messages in thread
From: Peng Fan @ 2017-08-28 7:17 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Stefano Babic [mailto:sbabic at denx.de]
> Sent: Monday, August 28, 2017 3:07 PM
> To: Peng Fan <peng.fan@nxp.com>; Jagan Teki <jagannadh.teki@gmail.com>
> Cc: Stefano Babic <sbabic@denx.de>; u-boot at lists.denx.de; Fabio Estevam
> <fabio.estevam@freescale.com>
> Subject: Re: [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
>
> Hi Jagan, Peng, Fabio,
>
> On 28/08/2017 08:45, Peng Fan wrote:
> >
> >
> >> -----Original Message-----
> >> From: Jagan Teki [mailto:jagannadh.teki at gmail.com]
> >> Sent: Monday, August 28, 2017 2:41 PM
> >> To: Peng Fan <peng.fan@nxp.com>
> >> Cc: Stefano Babic <sbabic@denx.de>; u-boot at lists.denx.de
> >> Subject: Re: [U-Boot] [PATCH V2 02/12] arm: dts: include dts for
> >> imx6sabresd
> >>
> >> On Mon, Aug 28, 2017 at 11:58 AM, Peng Fan <peng.fan@nxp.com> wrote:
> >>> Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd
> board.
> >>>
> >>> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> >>> Cc: Stefano Babic <sbabic@denx.de>
> >>> ---
> >>
> >> Similar series[1] with DTB support for sabresd
> >>
> >>
> >> [1] https://lists.denx.de/pipermail/u-boot/2017-May/293206.html
> >
> > I thought that thread was not active, since past 3 months. I'll leave Stefano to
> decide.
> >
>
> In my understanding, Jagan's series has still open coments from Joe regarding
> phy-reset. I have not seen a new post, and I confess I have then forgotten this
> series. I have not seen a review by Fabio, too, and he's the maintainer for sabre
> boards.
>
> Peng, I have just tried to build with your series, but it breaks many boards due
> to DTC issue. I have also tried to build with last DTC from git, but it does not
> help. Is it known to you ?
I only build mx6sabresd_defconfig, did not run buildman to build other boards,
Because I always met
/usr/include/python2.7/pyconfig.h:1207:0: warning: "_XOPEN_SOURCE" redefined [enabled by default]
#define _XOPEN_SOURCE 600
^
In file included from /usr/include/stdint.h:25:0,
I'll build other boards and fix the issue.
Thanks,
Peng.
>
> Best regards,
> Stefano
>
> --
> ============================================================
> =========
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> ============================================================
> =========
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 7:06 ` Stefano Babic
2017-08-28 7:17 ` Peng Fan
@ 2017-08-28 7:20 ` Jagan Teki
2017-08-28 7:29 ` Stefano Babic
2017-08-28 11:14 ` Fabio Estevam
2 siblings, 1 reply; 23+ messages in thread
From: Jagan Teki @ 2017-08-28 7:20 UTC (permalink / raw)
To: u-boot
Hi Stefano,
On Mon, Aug 28, 2017 at 12:36 PM, Stefano Babic <sbabic@denx.de> wrote:
> Hi Jagan, Peng, Fabio,
>
> On 28/08/2017 08:45, Peng Fan wrote:
>>
>>
>>> -----Original Message-----
>>> From: Jagan Teki [mailto:jagannadh.teki at gmail.com]
>>> Sent: Monday, August 28, 2017 2:41 PM
>>> To: Peng Fan <peng.fan@nxp.com>
>>> Cc: Stefano Babic <sbabic@denx.de>; u-boot at lists.denx.de
>>> Subject: Re: [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
>>>
>>> On Mon, Aug 28, 2017 at 11:58 AM, Peng Fan <peng.fan@nxp.com> wrote:
>>>> Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd board.
>>>>
>>>> Signed-off-by: Peng Fan <peng.fan@nxp.com>
>>>> Cc: Stefano Babic <sbabic@denx.de>
>>>> ---
>>>
>>> Similar series[1] with DTB support for sabresd
>>>
>>>
>>> [1] https://lists.denx.de/pipermail/u-boot/2017-May/293206.html
>>
>> I thought that thread was not active, since past 3 months. I'll leave Stefano to decide.
>>
>
> In my understanding, Jagan's series has still open coments from Joe
> regarding phy-reset. I have not seen a new post, and I confess I have
> then forgotten this series. I have not seen a review by Fabio, too, and
> he's the maintainer for sabre boards.
Yes, It's pause at NET and few dm errors. I will try to send next
version in couple of days if you're OK?
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 7:20 ` Jagan Teki
@ 2017-08-28 7:29 ` Stefano Babic
0 siblings, 0 replies; 23+ messages in thread
From: Stefano Babic @ 2017-08-28 7:29 UTC (permalink / raw)
To: u-boot
On 28/08/2017 09:20, Jagan Teki wrote:
> Hi Stefano,
>
> On Mon, Aug 28, 2017 at 12:36 PM, Stefano Babic <sbabic@denx.de> wrote:
>> Hi Jagan, Peng, Fabio,
>>
>> On 28/08/2017 08:45, Peng Fan wrote:
>>>
>>>
>>>> -----Original Message-----
>>>> From: Jagan Teki [mailto:jagannadh.teki at gmail.com]
>>>> Sent: Monday, August 28, 2017 2:41 PM
>>>> To: Peng Fan <peng.fan@nxp.com>
>>>> Cc: Stefano Babic <sbabic@denx.de>; u-boot at lists.denx.de
>>>> Subject: Re: [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
>>>>
>>>> On Mon, Aug 28, 2017 at 11:58 AM, Peng Fan <peng.fan@nxp.com> wrote:
>>>>> Import dts from commit aae4e7a8bc("Linux 4.13-rc4") for imx6sabresd board.
>>>>>
>>>>> Signed-off-by: Peng Fan <peng.fan@nxp.com>
>>>>> Cc: Stefano Babic <sbabic@denx.de>
>>>>> ---
>>>>
>>>> Similar series[1] with DTB support for sabresd
>>>>
>>>>
>>>> [1] https://lists.denx.de/pipermail/u-boot/2017-May/293206.html
>>>
>>> I thought that thread was not active, since past 3 months. I'll leave Stefano to decide.
>>>
>>
>> In my understanding, Jagan's series has still open coments from Joe
>> regarding phy-reset. I have not seen a new post, and I confess I have
>> then forgotten this series. I have not seen a review by Fabio, too, and
>> he's the maintainer for sabre boards.
>
> Yes, It's pause at NET and few dm errors. I will try to send next
> version in couple of days if you're OK?
The thing is that you and Peng series change the same set of files and
we need a kind of synchronization to avoid conflicts. I have seen V2
today from Peng, but this does not fix build issues.
Cheers,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
` (10 preceding siblings ...)
2017-08-28 6:29 ` [U-Boot] [PATCH V2 12/12] imx: mx6sabresd: update README Peng Fan
@ 2017-08-28 7:32 ` Stefano Babic
2017-08-28 7:36 ` Peng Fan
11 siblings, 1 reply; 23+ messages in thread
From: Stefano Babic @ 2017-08-28 7:32 UTC (permalink / raw)
To: u-boot
On 28/08/2017 08:28, Peng Fan wrote:
> Typo fix: CONIFG->CONFIG
>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> Cc: Tom Rini <trini@konsulko.com>
> ---
>
> V2: none
Just to reduce my confusion: this was V2 or V3 ?
Regards,
Stefano
>
> scripts/Makefile.uncmd_spl | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/scripts/Makefile.uncmd_spl b/scripts/Makefile.uncmd_spl
> index 15d0836..b399411 100644
> --- a/scripts/Makefile.uncmd_spl
> +++ b/scripts/Makefile.uncmd_spl
> @@ -9,7 +9,7 @@ ifdef CONFIG_SPL_BUILD
> ifndef CONFIG_SPL_DM
> CONFIG_DM_SERIAL=
> CONFIG_DM_GPIO=
> -CONIFG_DM_I2C=
> +CONFIG_DM_I2C=
> CONFIG_DM_SPI=
> CONFIG_DM_SPI_FLASH=
> endif
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo
2017-08-28 7:32 ` [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Stefano Babic
@ 2017-08-28 7:36 ` Peng Fan
2017-08-28 7:41 ` Stefano Babic
0 siblings, 1 reply; 23+ messages in thread
From: Peng Fan @ 2017-08-28 7:36 UTC (permalink / raw)
To: u-boot
> -----Original Message-----
> From: Stefano Babic [mailto:sbabic at denx.de]
> Sent: Monday, August 28, 2017 3:33 PM
> To: Peng Fan <peng.fan@nxp.com>; sbabic at denx.de
> Cc: van.freenix at gmail.com; u-boot at lists.denx.de; Tom Rini
> <trini@konsulko.com>
> Subject: Re: [PATCH V2 01/12] scripts: spl: fix typo
>
> On 28/08/2017 08:28, Peng Fan wrote:
> > Typo fix: CONIFG->CONFIG
> >
> > Signed-off-by: Peng Fan <peng.fan@nxp.com>
> > Cc: Tom Rini <trini@konsulko.com>
> > ---
> >
> > V2: none
>
> Just to reduce my confusion: this was V2 or V3 ?
Sorry, this should be v3. In this patchset, only
added Simon's r-b and addressed a few minor comments.
No much changed.
Thanks,
Peng.
>
> Regards,
> Stefano
>
> >
> > scripts/Makefile.uncmd_spl | 2 +-
> > 1 file changed, 1 insertion(+), 1 deletion(-)
> >
> > diff --git a/scripts/Makefile.uncmd_spl b/scripts/Makefile.uncmd_spl
> > index 15d0836..b399411 100644
> > --- a/scripts/Makefile.uncmd_spl
> > +++ b/scripts/Makefile.uncmd_spl
> > @@ -9,7 +9,7 @@ ifdef CONFIG_SPL_BUILD ifndef CONFIG_SPL_DM
> > CONFIG_DM_SERIAL= CONFIG_DM_GPIO= -CONIFG_DM_I2C=
> > +CONFIG_DM_I2C=
> > CONFIG_DM_SPI=
> > CONFIG_DM_SPI_FLASH=
> > endif
> >
>
>
> --
> ============================================================
> =========
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
> ============================================================
> =========
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo
2017-08-28 7:36 ` Peng Fan
@ 2017-08-28 7:41 ` Stefano Babic
0 siblings, 0 replies; 23+ messages in thread
From: Stefano Babic @ 2017-08-28 7:41 UTC (permalink / raw)
To: u-boot
On 28/08/2017 09:36, Peng Fan wrote:
>
>
>> -----Original Message-----
>> From: Stefano Babic [mailto:sbabic at denx.de]
>> Sent: Monday, August 28, 2017 3:33 PM
>> To: Peng Fan <peng.fan@nxp.com>; sbabic at denx.de
>> Cc: van.freenix at gmail.com; u-boot at lists.denx.de; Tom Rini
>> <trini@konsulko.com>
>> Subject: Re: [PATCH V2 01/12] scripts: spl: fix typo
>>
>> On 28/08/2017 08:28, Peng Fan wrote:
>>> Typo fix: CONIFG->CONFIG
>>>
>>> Signed-off-by: Peng Fan <peng.fan@nxp.com>
>>> Cc: Tom Rini <trini@konsulko.com>
>>> ---
>>>
>>> V2: none
>>
>> Just to reduce my confusion: this was V2 or V3 ?
>
> Sorry, this should be v3. In this patchset, only
> added Simon's r-b and addressed a few minor comments.
> No much changed.
>
Ok, thanks. I put the status into "Changes requested" and I'll wait for V4.
Regards,
Stefano
> Thanks,
> Peng.
>
>
>>
>> Regards,
>> Stefano
>>
>>>
>>> scripts/Makefile.uncmd_spl | 2 +-
>>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>>
>>> diff --git a/scripts/Makefile.uncmd_spl b/scripts/Makefile.uncmd_spl
>>> index 15d0836..b399411 100644
>>> --- a/scripts/Makefile.uncmd_spl
>>> +++ b/scripts/Makefile.uncmd_spl
>>> @@ -9,7 +9,7 @@ ifdef CONFIG_SPL_BUILD ifndef CONFIG_SPL_DM
>>> CONFIG_DM_SERIAL= CONFIG_DM_GPIO= -CONIFG_DM_I2C=
>>> +CONFIG_DM_I2C=
>>> CONFIG_DM_SPI=
>>> CONFIG_DM_SPI_FLASH=
>>> endif
>>>
>>
>>
>> --
>> ============================================================
>> =========
>> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
>> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
>> Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
>> ============================================================
>> =========
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd
2017-08-28 7:06 ` Stefano Babic
2017-08-28 7:17 ` Peng Fan
2017-08-28 7:20 ` Jagan Teki
@ 2017-08-28 11:14 ` Fabio Estevam
2 siblings, 0 replies; 23+ messages in thread
From: Fabio Estevam @ 2017-08-28 11:14 UTC (permalink / raw)
To: u-boot
On Mon, Aug 28, 2017 at 4:06 AM, Stefano Babic <sbabic@denx.de> wrote:
> In my understanding, Jagan's series has still open coments from Joe
> regarding phy-reset. I have not seen a new post, and I confess I have
> then forgotten this series. I have not seen a review by Fabio, too, and
> he's the maintainer for sabre boards.
Yes, last time I tested Jagan's series Ethernet was not functional
with dtb support.
Thanks
^ permalink raw reply [flat|nested] 23+ messages in thread
* [U-Boot] [PATCH V2 10/12] board: freescale: common: add pfuze dm code
2017-08-28 6:29 ` [U-Boot] [PATCH V2 10/12] board: freescale: common: add pfuze dm code Peng Fan
@ 2017-08-28 16:26 ` York Sun
0 siblings, 0 replies; 23+ messages in thread
From: York Sun @ 2017-08-28 16:26 UTC (permalink / raw)
To: u-boot
On 08/27/2017 11:30 PM, Peng Fan wrote:
> Add pfuze dm code, this code does the same thing as pfuze.c, but
> only effects when CONFIG_$(SPL_)DM_PMIC_PFUZE100 enabled.
>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> Cc: York Sun <york.sun@nxp.com>
> Cc: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
>
> V2: none
>
> board/freescale/common/Makefile | 1 +
> board/freescale/common/pfuze.h | 5 +++
> board/freescale/common/pfuze_dm.c | 89 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 95 insertions(+)
> create mode 100644 board/freescale/common/pfuze_dm.c
>
> diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
> index 1c53fb6..620dced 100644
> --- a/board/freescale/common/Makefile
> +++ b/board/freescale/common/Makefile
> @@ -61,6 +61,7 @@ obj-$(CONFIG_VSC_CROSSBAR) += vsc3316_3308.o
> obj-$(CONFIG_IDT8T49N222A) += idt8t49n222a_serdes_clk.o
> obj-$(CONFIG_ZM7300) += zm7300.o
> obj-$(CONFIG_POWER_PFUZE100) += pfuze.o
> +obj-$(CONFIG_$(SPL_)DM_PMIC_PFUZE100) += pfuze_dm.o
> obj-$(CONFIG_POWER_MC34VR500) += mc34vr500.o
>
> obj-$(CONFIG_LS102XA_STREAM_ID) += ls102xa_stream_id.o
> diff --git a/board/freescale/common/pfuze.h b/board/freescale/common/pfuze.h
> index 53cfc99..9c4c92a 100644
> --- a/board/freescale/common/pfuze.h
> +++ b/board/freescale/common/pfuze.h
> @@ -7,7 +7,12 @@
> #ifndef __PFUZE_BOARD_HELPER__
> #define __PFUZE_BOARD_HELPER__
>
> +#if CONFIG_IS_ENABLED(DM_PMIC_PFUZE100)
Is this SPL safe? I guess you can have CONFIG_SPL_DM_PMIC_PFUZE100
according to you change to Makefile.
York
^ permalink raw reply [flat|nested] 23+ messages in thread
end of thread, other threads:[~2017-08-28 16:26 UTC | newest]
Thread overview: 23+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-08-28 6:28 [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 02/12] arm: dts: include dts for imx6sabresd Peng Fan
2017-08-28 6:40 ` Jagan Teki
2017-08-28 6:45 ` Peng Fan
2017-08-28 7:06 ` Stefano Babic
2017-08-28 7:17 ` Peng Fan
2017-08-28 7:20 ` Jagan Teki
2017-08-28 7:29 ` Stefano Babic
2017-08-28 11:14 ` Fabio Estevam
2017-08-28 6:28 ` [U-Boot] [PATCH V2 03/12] power: pmic/regulator allow dm be omited by SPL Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 04/12] Makefile: build FIT image if CONFIG_SPL_FIT_GENERATOR defined Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 05/12] imx: introduce mkimage_fit.sh Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 06/12] imx: mx6sabresd: implement board_fit_config_name_match Peng Fan
2017-08-28 6:28 ` [U-Boot] [PATCH V2 07/12] imx: mx6sabresd: enable SPL FIT Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 08/12] mmc: fsl_esdhc: switch to use CONFIG_IS_ENABLED Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 09/12] power: pmic.h: include dm/ofnode.h Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 10/12] board: freescale: common: add pfuze dm code Peng Fan
2017-08-28 16:26 ` York Sun
2017-08-28 6:29 ` [U-Boot] [PATCH V2 11/12] imx: mx6sabresd: enable dm drivers Peng Fan
2017-08-28 6:29 ` [U-Boot] [PATCH V2 12/12] imx: mx6sabresd: update README Peng Fan
2017-08-28 7:32 ` [U-Boot] [PATCH V2 01/12] scripts: spl: fix typo Stefano Babic
2017-08-28 7:36 ` Peng Fan
2017-08-28 7:41 ` Stefano Babic
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.