From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1751464AbdH1NAL (ORCPT ); Mon, 28 Aug 2017 09:00:11 -0400 Received: from mx07-00178001.pphosted.com ([62.209.51.94]:53775 "EHLO mx07-00178001.pphosted.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751164AbdH1NAJ (ORCPT ); Mon, 28 Aug 2017 09:00:09 -0400 From: Fabrice Gasnier To: , , , CC: , , , , , , Subject: [RESEND PATCH 2/3] regulator: Add support for stm32-vrefbuf Date: Mon, 28 Aug 2017 14:58:52 +0200 Message-ID: <1503925133-30722-3-git-send-email-fabrice.gasnier@st.com> X-Mailer: git-send-email 1.9.1 In-Reply-To: <1503925133-30722-1-git-send-email-fabrice.gasnier@st.com> References: <1503925133-30722-1-git-send-email-fabrice.gasnier@st.com> MIME-Version: 1.0 Content-Type: text/plain X-Originating-IP: [10.75.127.47] X-ClientProxiedBy: SFHDAG3NODE1.st.com (10.75.127.7) To SFHDAG5NODE3.st.com (10.75.127.15) X-Proofpoint-Virus-Version: vendor=fsecure engine=2.50.10432:,, definitions=2017-08-28_06:,, signatures=0 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Add regulator driver for STM32 voltage reference buffer which can be used as voltage reference for ADCs, DACs and external components through dedicated VREF+ pin. Signed-off-by: Fabrice Gasnier --- drivers/regulator/Kconfig | 12 +++ drivers/regulator/Makefile | 1 + drivers/regulator/stm32-vrefbuf.c | 215 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 228 insertions(+) create mode 100644 drivers/regulator/stm32-vrefbuf.c diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index 99b9362..2cb2c63 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -746,6 +746,18 @@ config REGULATOR_SKY81452 This driver can also be built as a module. If so, the module will be called sky81452-regulator. +config REGULATOR_STM32_VREFBUF + tristate "STMicroelectronics STM32 VREFBUF" + depends on ARCH_STM32 || COMPILE_TEST + help + This driver supports STMicroelectronics STM32 VREFBUF (voltage + reference buffer) which can be used as voltage reference for + internal ADCs, DACs and also for external components through + dedicated Vref+ pin. + + This driver can also be built as a module. If so, the module + will be called stm32-vrefbuf. + config REGULATOR_TI_ABB tristate "TI Adaptive Body Bias on-chip LDO" depends on ARCH_OMAP diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 95b1e86..5af3788 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -94,6 +94,7 @@ obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o +obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o diff --git a/drivers/regulator/stm32-vrefbuf.c b/drivers/regulator/stm32-vrefbuf.c new file mode 100644 index 0000000..a4efa3b --- /dev/null +++ b/drivers/regulator/stm32-vrefbuf.c @@ -0,0 +1,215 @@ +/* + * Copyright (C) STMicroelectronics 2017 + * + * Author: Fabrice Gasnier + * + * License terms: GNU General Public License (GPL), version 2 + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* STM32 VREFBUF registers */ +#define STM32_VREFBUF_CSR 0x00 + +/* STM32 VREFBUF CSR bitfields */ +#define STM32_VRS GENMASK(6, 4) +#define STM32_VRR BIT(3) +#define STM32_HIZ BIT(1) +#define STM32_ENVR BIT(0) + +struct stm32_vrefbuf { + void __iomem *base; + struct clk *clk; +}; + +static const unsigned int stm32_vrefbuf_voltages[] = { + /* Matches resp. VRS = 000b, 001b, 010b, 011b */ + 2500000, 2048000, 1800000, 1500000, +}; + +static int stm32_vrefbuf_enable(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + int ret; + + val = (val & ~STM32_HIZ) | STM32_ENVR; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + /* + * Vrefbuf startup time depends on external capacitor: wait here for + * VRR to be set. That means output has reached expected value. + * ~650us sleep should be enough for caps up to 1.5uF. Use 10ms as + * arbitrary timeout. + */ + ret = readl_poll_timeout(priv->base + STM32_VREFBUF_CSR, val, + !(val & STM32_VRR), 650, 10000); + if (ret) { + dev_err(&rdev->dev, "stm32 vrefbuf timed out!\n"); + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + val = (val & ~STM32_ENVR) | STM32_HIZ; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + } + + return ret; +} + +static int stm32_vrefbuf_disable(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + val = (val & ~STM32_ENVR) | STM32_HIZ; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + return 0; +} + +static int stm32_vrefbuf_is_enabled(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + return readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR; +} + +static int stm32_vrefbuf_set_voltage_sel(struct regulator_dev *rdev, + unsigned sel) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + val = (val & ~STM32_VRS) | FIELD_PREP(STM32_VRS, sel); + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + return 0; +} + +static int stm32_vrefbuf_get_voltage_sel(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + return FIELD_GET(STM32_VRS, val); +} + +static const struct regulator_ops stm32_vrefbuf_volt_ops = { + .enable = stm32_vrefbuf_enable, + .disable = stm32_vrefbuf_disable, + .is_enabled = stm32_vrefbuf_is_enabled, + .get_voltage_sel = stm32_vrefbuf_get_voltage_sel, + .set_voltage_sel = stm32_vrefbuf_set_voltage_sel, + .list_voltage = regulator_list_voltage_table, +}; + +static const struct regulator_desc stm32_vrefbuf_regu = { + .name = "vref", + .supply_name = "vdda", + .volt_table = stm32_vrefbuf_voltages, + .n_voltages = ARRAY_SIZE(stm32_vrefbuf_voltages), + .ops = &stm32_vrefbuf_volt_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static int stm32_vrefbuf_probe(struct platform_device *pdev) +{ + struct resource *res; + struct stm32_vrefbuf *priv; + struct regulator_config config = { }; + struct regulator_dev *rdev; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + ret = clk_prepare_enable(priv->clk); + if (ret) { + dev_err(&pdev->dev, "clk prepare failed\n"); + return ret; + } + + config.dev = &pdev->dev; + config.driver_data = priv; + config.of_node = pdev->dev.of_node; + config.init_data = of_get_regulator_init_data(&pdev->dev, + pdev->dev.of_node, + &stm32_vrefbuf_regu); + + rdev = regulator_register(&stm32_vrefbuf_regu, &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "vrefbuf register failed\n"); + ret = PTR_ERR(rdev); + goto err_clk_dis; + } + platform_set_drvdata(pdev, rdev); + + dev_info(&pdev->dev, "STM32 VREFBUF initialized\n"); + + return 0; + +err_clk_dis: + clk_disable_unprepare(priv->clk); + + return ret; +} + +static int stm32_vrefbuf_remove(struct platform_device *pdev) +{ + struct regulator_dev *rdev = platform_get_drvdata(pdev); + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + regulator_unregister(rdev); + clk_disable_unprepare(priv->clk); + + return 0; +}; + +static const struct of_device_id stm32_vrefbuf_of_match[] = { + { .compatible = "st,stm32-vrefbuf", }, + {}, +}; +MODULE_DEVICE_TABLE(of, stm32_vrefbuf_of_match); + +static struct platform_driver stm32_vrefbuf_driver = { + .probe = stm32_vrefbuf_probe, + .remove = stm32_vrefbuf_remove, + .driver = { + .name = "stm32-vrefbuf", + .of_match_table = of_match_ptr(stm32_vrefbuf_of_match), + }, +}; + +static int __init stm32_vrefbuf_init(void) +{ + return platform_driver_register(&stm32_vrefbuf_driver); +} +subsys_initcall(stm32_vrefbuf_init); + +static void __exit stm32_vrefbuf_exit(void) +{ + platform_driver_unregister(&stm32_vrefbuf_driver); +} +module_exit(stm32_vrefbuf_exit) + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Fabrice Gasnier "); +MODULE_DESCRIPTION("STMicroelectronics STM32 VREFBUF driver"); +MODULE_ALIAS("platform:stm32-vrefbuf"); -- 1.9.1 From mboxrd@z Thu Jan 1 00:00:00 1970 From: Fabrice Gasnier Subject: [RESEND PATCH 2/3] regulator: Add support for stm32-vrefbuf Date: Mon, 28 Aug 2017 14:58:52 +0200 Message-ID: <1503925133-30722-3-git-send-email-fabrice.gasnier@st.com> References: <1503925133-30722-1-git-send-email-fabrice.gasnier@st.com> Mime-Version: 1.0 Content-Type: text/plain Return-path: In-Reply-To: <1503925133-30722-1-git-send-email-fabrice.gasnier-qxv4g6HH51o@public.gmane.org> Sender: devicetree-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org, lgirdwood-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org, alexandre.torgue-qxv4g6HH51o@public.gmane.org Cc: mark.rutland-5wv7dgnIgG8@public.gmane.org, mcoquelin.stm32-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, fabrice.gasnier-qxv4g6HH51o@public.gmane.org, linux-I+IVW8TIWO2tmTQ+vhA3Yw@public.gmane.org, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org List-Id: devicetree@vger.kernel.org Add regulator driver for STM32 voltage reference buffer which can be used as voltage reference for ADCs, DACs and external components through dedicated VREF+ pin. Signed-off-by: Fabrice Gasnier --- drivers/regulator/Kconfig | 12 +++ drivers/regulator/Makefile | 1 + drivers/regulator/stm32-vrefbuf.c | 215 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 228 insertions(+) create mode 100644 drivers/regulator/stm32-vrefbuf.c diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index 99b9362..2cb2c63 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -746,6 +746,18 @@ config REGULATOR_SKY81452 This driver can also be built as a module. If so, the module will be called sky81452-regulator. +config REGULATOR_STM32_VREFBUF + tristate "STMicroelectronics STM32 VREFBUF" + depends on ARCH_STM32 || COMPILE_TEST + help + This driver supports STMicroelectronics STM32 VREFBUF (voltage + reference buffer) which can be used as voltage reference for + internal ADCs, DACs and also for external components through + dedicated Vref+ pin. + + This driver can also be built as a module. If so, the module + will be called stm32-vrefbuf. + config REGULATOR_TI_ABB tristate "TI Adaptive Body Bias on-chip LDO" depends on ARCH_OMAP diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 95b1e86..5af3788 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -94,6 +94,7 @@ obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o +obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o diff --git a/drivers/regulator/stm32-vrefbuf.c b/drivers/regulator/stm32-vrefbuf.c new file mode 100644 index 0000000..a4efa3b --- /dev/null +++ b/drivers/regulator/stm32-vrefbuf.c @@ -0,0 +1,215 @@ +/* + * Copyright (C) STMicroelectronics 2017 + * + * Author: Fabrice Gasnier + * + * License terms: GNU General Public License (GPL), version 2 + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* STM32 VREFBUF registers */ +#define STM32_VREFBUF_CSR 0x00 + +/* STM32 VREFBUF CSR bitfields */ +#define STM32_VRS GENMASK(6, 4) +#define STM32_VRR BIT(3) +#define STM32_HIZ BIT(1) +#define STM32_ENVR BIT(0) + +struct stm32_vrefbuf { + void __iomem *base; + struct clk *clk; +}; + +static const unsigned int stm32_vrefbuf_voltages[] = { + /* Matches resp. VRS = 000b, 001b, 010b, 011b */ + 2500000, 2048000, 1800000, 1500000, +}; + +static int stm32_vrefbuf_enable(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + int ret; + + val = (val & ~STM32_HIZ) | STM32_ENVR; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + /* + * Vrefbuf startup time depends on external capacitor: wait here for + * VRR to be set. That means output has reached expected value. + * ~650us sleep should be enough for caps up to 1.5uF. Use 10ms as + * arbitrary timeout. + */ + ret = readl_poll_timeout(priv->base + STM32_VREFBUF_CSR, val, + !(val & STM32_VRR), 650, 10000); + if (ret) { + dev_err(&rdev->dev, "stm32 vrefbuf timed out!\n"); + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + val = (val & ~STM32_ENVR) | STM32_HIZ; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + } + + return ret; +} + +static int stm32_vrefbuf_disable(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + val = (val & ~STM32_ENVR) | STM32_HIZ; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + return 0; +} + +static int stm32_vrefbuf_is_enabled(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + return readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR; +} + +static int stm32_vrefbuf_set_voltage_sel(struct regulator_dev *rdev, + unsigned sel) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + val = (val & ~STM32_VRS) | FIELD_PREP(STM32_VRS, sel); + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + return 0; +} + +static int stm32_vrefbuf_get_voltage_sel(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + return FIELD_GET(STM32_VRS, val); +} + +static const struct regulator_ops stm32_vrefbuf_volt_ops = { + .enable = stm32_vrefbuf_enable, + .disable = stm32_vrefbuf_disable, + .is_enabled = stm32_vrefbuf_is_enabled, + .get_voltage_sel = stm32_vrefbuf_get_voltage_sel, + .set_voltage_sel = stm32_vrefbuf_set_voltage_sel, + .list_voltage = regulator_list_voltage_table, +}; + +static const struct regulator_desc stm32_vrefbuf_regu = { + .name = "vref", + .supply_name = "vdda", + .volt_table = stm32_vrefbuf_voltages, + .n_voltages = ARRAY_SIZE(stm32_vrefbuf_voltages), + .ops = &stm32_vrefbuf_volt_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static int stm32_vrefbuf_probe(struct platform_device *pdev) +{ + struct resource *res; + struct stm32_vrefbuf *priv; + struct regulator_config config = { }; + struct regulator_dev *rdev; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + ret = clk_prepare_enable(priv->clk); + if (ret) { + dev_err(&pdev->dev, "clk prepare failed\n"); + return ret; + } + + config.dev = &pdev->dev; + config.driver_data = priv; + config.of_node = pdev->dev.of_node; + config.init_data = of_get_regulator_init_data(&pdev->dev, + pdev->dev.of_node, + &stm32_vrefbuf_regu); + + rdev = regulator_register(&stm32_vrefbuf_regu, &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "vrefbuf register failed\n"); + ret = PTR_ERR(rdev); + goto err_clk_dis; + } + platform_set_drvdata(pdev, rdev); + + dev_info(&pdev->dev, "STM32 VREFBUF initialized\n"); + + return 0; + +err_clk_dis: + clk_disable_unprepare(priv->clk); + + return ret; +} + +static int stm32_vrefbuf_remove(struct platform_device *pdev) +{ + struct regulator_dev *rdev = platform_get_drvdata(pdev); + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + regulator_unregister(rdev); + clk_disable_unprepare(priv->clk); + + return 0; +}; + +static const struct of_device_id stm32_vrefbuf_of_match[] = { + { .compatible = "st,stm32-vrefbuf", }, + {}, +}; +MODULE_DEVICE_TABLE(of, stm32_vrefbuf_of_match); + +static struct platform_driver stm32_vrefbuf_driver = { + .probe = stm32_vrefbuf_probe, + .remove = stm32_vrefbuf_remove, + .driver = { + .name = "stm32-vrefbuf", + .of_match_table = of_match_ptr(stm32_vrefbuf_of_match), + }, +}; + +static int __init stm32_vrefbuf_init(void) +{ + return platform_driver_register(&stm32_vrefbuf_driver); +} +subsys_initcall(stm32_vrefbuf_init); + +static void __exit stm32_vrefbuf_exit(void) +{ + platform_driver_unregister(&stm32_vrefbuf_driver); +} +module_exit(stm32_vrefbuf_exit) + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Fabrice Gasnier "); +MODULE_DESCRIPTION("STMicroelectronics STM32 VREFBUF driver"); +MODULE_ALIAS("platform:stm32-vrefbuf"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html From mboxrd@z Thu Jan 1 00:00:00 1970 From: fabrice.gasnier@st.com (Fabrice Gasnier) Date: Mon, 28 Aug 2017 14:58:52 +0200 Subject: [RESEND PATCH 2/3] regulator: Add support for stm32-vrefbuf In-Reply-To: <1503925133-30722-1-git-send-email-fabrice.gasnier@st.com> References: <1503925133-30722-1-git-send-email-fabrice.gasnier@st.com> Message-ID: <1503925133-30722-3-git-send-email-fabrice.gasnier@st.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Add regulator driver for STM32 voltage reference buffer which can be used as voltage reference for ADCs, DACs and external components through dedicated VREF+ pin. Signed-off-by: Fabrice Gasnier --- drivers/regulator/Kconfig | 12 +++ drivers/regulator/Makefile | 1 + drivers/regulator/stm32-vrefbuf.c | 215 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 228 insertions(+) create mode 100644 drivers/regulator/stm32-vrefbuf.c diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index 99b9362..2cb2c63 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -746,6 +746,18 @@ config REGULATOR_SKY81452 This driver can also be built as a module. If so, the module will be called sky81452-regulator. +config REGULATOR_STM32_VREFBUF + tristate "STMicroelectronics STM32 VREFBUF" + depends on ARCH_STM32 || COMPILE_TEST + help + This driver supports STMicroelectronics STM32 VREFBUF (voltage + reference buffer) which can be used as voltage reference for + internal ADCs, DACs and also for external components through + dedicated Vref+ pin. + + This driver can also be built as a module. If so, the module + will be called stm32-vrefbuf. + config REGULATOR_TI_ABB tristate "TI Adaptive Body Bias on-chip LDO" depends on ARCH_OMAP diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index 95b1e86..5af3788 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -94,6 +94,7 @@ obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o +obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o diff --git a/drivers/regulator/stm32-vrefbuf.c b/drivers/regulator/stm32-vrefbuf.c new file mode 100644 index 0000000..a4efa3b --- /dev/null +++ b/drivers/regulator/stm32-vrefbuf.c @@ -0,0 +1,215 @@ +/* + * Copyright (C) STMicroelectronics 2017 + * + * Author: Fabrice Gasnier + * + * License terms: GNU General Public License (GPL), version 2 + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* STM32 VREFBUF registers */ +#define STM32_VREFBUF_CSR 0x00 + +/* STM32 VREFBUF CSR bitfields */ +#define STM32_VRS GENMASK(6, 4) +#define STM32_VRR BIT(3) +#define STM32_HIZ BIT(1) +#define STM32_ENVR BIT(0) + +struct stm32_vrefbuf { + void __iomem *base; + struct clk *clk; +}; + +static const unsigned int stm32_vrefbuf_voltages[] = { + /* Matches resp. VRS = 000b, 001b, 010b, 011b */ + 2500000, 2048000, 1800000, 1500000, +}; + +static int stm32_vrefbuf_enable(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + int ret; + + val = (val & ~STM32_HIZ) | STM32_ENVR; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + /* + * Vrefbuf startup time depends on external capacitor: wait here for + * VRR to be set. That means output has reached expected value. + * ~650us sleep should be enough for caps up to 1.5uF. Use 10ms as + * arbitrary timeout. + */ + ret = readl_poll_timeout(priv->base + STM32_VREFBUF_CSR, val, + !(val & STM32_VRR), 650, 10000); + if (ret) { + dev_err(&rdev->dev, "stm32 vrefbuf timed out!\n"); + val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + val = (val & ~STM32_ENVR) | STM32_HIZ; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + } + + return ret; +} + +static int stm32_vrefbuf_disable(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + val = (val & ~STM32_ENVR) | STM32_HIZ; + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + return 0; +} + +static int stm32_vrefbuf_is_enabled(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + return readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR; +} + +static int stm32_vrefbuf_set_voltage_sel(struct regulator_dev *rdev, + unsigned sel) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + val = (val & ~STM32_VRS) | FIELD_PREP(STM32_VRS, sel); + writel_relaxed(val, priv->base + STM32_VREFBUF_CSR); + + return 0; +} + +static int stm32_vrefbuf_get_voltage_sel(struct regulator_dev *rdev) +{ + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + u32 val = readl_relaxed(priv->base + STM32_VREFBUF_CSR); + + return FIELD_GET(STM32_VRS, val); +} + +static const struct regulator_ops stm32_vrefbuf_volt_ops = { + .enable = stm32_vrefbuf_enable, + .disable = stm32_vrefbuf_disable, + .is_enabled = stm32_vrefbuf_is_enabled, + .get_voltage_sel = stm32_vrefbuf_get_voltage_sel, + .set_voltage_sel = stm32_vrefbuf_set_voltage_sel, + .list_voltage = regulator_list_voltage_table, +}; + +static const struct regulator_desc stm32_vrefbuf_regu = { + .name = "vref", + .supply_name = "vdda", + .volt_table = stm32_vrefbuf_voltages, + .n_voltages = ARRAY_SIZE(stm32_vrefbuf_voltages), + .ops = &stm32_vrefbuf_volt_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static int stm32_vrefbuf_probe(struct platform_device *pdev) +{ + struct resource *res; + struct stm32_vrefbuf *priv; + struct regulator_config config = { }; + struct regulator_dev *rdev; + int ret; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + ret = clk_prepare_enable(priv->clk); + if (ret) { + dev_err(&pdev->dev, "clk prepare failed\n"); + return ret; + } + + config.dev = &pdev->dev; + config.driver_data = priv; + config.of_node = pdev->dev.of_node; + config.init_data = of_get_regulator_init_data(&pdev->dev, + pdev->dev.of_node, + &stm32_vrefbuf_regu); + + rdev = regulator_register(&stm32_vrefbuf_regu, &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "vrefbuf register failed\n"); + ret = PTR_ERR(rdev); + goto err_clk_dis; + } + platform_set_drvdata(pdev, rdev); + + dev_info(&pdev->dev, "STM32 VREFBUF initialized\n"); + + return 0; + +err_clk_dis: + clk_disable_unprepare(priv->clk); + + return ret; +} + +static int stm32_vrefbuf_remove(struct platform_device *pdev) +{ + struct regulator_dev *rdev = platform_get_drvdata(pdev); + struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev); + + regulator_unregister(rdev); + clk_disable_unprepare(priv->clk); + + return 0; +}; + +static const struct of_device_id stm32_vrefbuf_of_match[] = { + { .compatible = "st,stm32-vrefbuf", }, + {}, +}; +MODULE_DEVICE_TABLE(of, stm32_vrefbuf_of_match); + +static struct platform_driver stm32_vrefbuf_driver = { + .probe = stm32_vrefbuf_probe, + .remove = stm32_vrefbuf_remove, + .driver = { + .name = "stm32-vrefbuf", + .of_match_table = of_match_ptr(stm32_vrefbuf_of_match), + }, +}; + +static int __init stm32_vrefbuf_init(void) +{ + return platform_driver_register(&stm32_vrefbuf_driver); +} +subsys_initcall(stm32_vrefbuf_init); + +static void __exit stm32_vrefbuf_exit(void) +{ + platform_driver_unregister(&stm32_vrefbuf_driver); +} +module_exit(stm32_vrefbuf_exit) + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Fabrice Gasnier "); +MODULE_DESCRIPTION("STMicroelectronics STM32 VREFBUF driver"); +MODULE_ALIAS("platform:stm32-vrefbuf"); -- 1.9.1