* [U-Boot] [PATCH v3 0/7] Add support for GE PPD
@ 2017-11-01 14:23 Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 1/7] imx: mxc_i2c: tweak the i2c transfer method Martyn Welch
` (6 more replies)
0 siblings, 7 replies; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
This series adds support for the GE PPD. The initial patches in this
series resolve issues found during development and testing, extend
existing support and add new support for devices in the PPD. The final
patch in the series adds the board support for the PPD.
Ian Ray (2):
ext4: recover from filesystem corruption when reading
bootcount: add support for bootcounter on EXT filesystem
Martyn Welch (2):
pwm: imx: Enable PWM support on i.MX53
arm: mx5: Add more register definitions
Nandor Han (2):
imx: mxc_i2c: tweak the i2c transfer method
rtc: add support for s35392a
Peter Senna Tschudin (1):
mx53: Add Board support for GE PPD
README | 7 +
arch/arm/include/asm/arch-mx5/crm_regs.h | 9 +
arch/arm/include/asm/arch-mx5/imx-regs.h | 47 +++
arch/arm/include/asm/mach-types.h | 1 +
arch/arm/mach-imx/mx5/Kconfig | 5 +
board/freescale/mx53ppd/Kconfig | 17 ++
board/freescale/mx53ppd/MAINTAINERS | 7 +
board/freescale/mx53ppd/Makefile | 12 +
board/freescale/mx53ppd/imximage.cfg | 87 ++++++
board/freescale/mx53ppd/mx53ppd.c | 487 +++++++++++++++++++++++++++++++
board/freescale/mx53ppd/mx53ppd_video.c | 123 ++++++++
board/freescale/mx53ppd/ppd_gpio.h | 96 ++++++
board/freescale/mx53ppd/vpd_reader.c | 230 +++++++++++++++
board/freescale/mx53ppd/vpd_reader.h | 25 ++
configs/mx53ppd_defconfig | 39 +++
drivers/Kconfig | 2 +
drivers/bootcount/Kconfig | 57 ++++
drivers/bootcount/Makefile | 1 +
drivers/bootcount/bootcount_ext.c | 59 ++++
drivers/i2c/mxc_i2c.c | 25 +-
drivers/pwm/pwm-imx-util.c | 2 +
drivers/rtc/Kconfig | 6 +
drivers/rtc/Makefile | 1 +
drivers/rtc/s35392a.c | 360 +++++++++++++++++++++++
fs/ext4/ext4_common.c | 10 +
fs/ext4/ext4fs.c | 10 +-
include/configs/mx53ppd.h | 246 ++++++++++++++++
lib/Kconfig | 3 +
28 files changed, 1963 insertions(+), 11 deletions(-)
create mode 100644 board/freescale/mx53ppd/Kconfig
create mode 100644 board/freescale/mx53ppd/MAINTAINERS
create mode 100644 board/freescale/mx53ppd/Makefile
create mode 100644 board/freescale/mx53ppd/imximage.cfg
create mode 100644 board/freescale/mx53ppd/mx53ppd.c
create mode 100644 board/freescale/mx53ppd/mx53ppd_video.c
create mode 100644 board/freescale/mx53ppd/ppd_gpio.h
create mode 100644 board/freescale/mx53ppd/vpd_reader.c
create mode 100644 board/freescale/mx53ppd/vpd_reader.h
create mode 100644 configs/mx53ppd_defconfig
create mode 100644 drivers/bootcount/Kconfig
create mode 100644 drivers/bootcount/bootcount_ext.c
create mode 100644 drivers/rtc/s35392a.c
create mode 100644 include/configs/mx53ppd.h
--
2.1.4
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 1/7] imx: mxc_i2c: tweak the i2c transfer method
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 2/7] ext4: recover from filesystem corruption when reading Martyn Welch
` (5 subsequent siblings)
6 siblings, 0 replies; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
From: Nandor Han <nandor.han@ge.com>
Tweak the i2c transfer to work for devices that want to read data
without addressing a register.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
---
Changes for v2:
- Replacing '!= -1' with '>= 0'.
drivers/i2c/mxc_i2c.c | 25 +++++++++++++++----------
1 file changed, 15 insertions(+), 10 deletions(-)
diff --git a/drivers/i2c/mxc_i2c.c b/drivers/i2c/mxc_i2c.c
index abf1da2..205274e 100644
--- a/drivers/i2c/mxc_i2c.c
+++ b/drivers/i2c/mxc_i2c.c
@@ -317,16 +317,19 @@ static int i2c_init_transfer_(struct mxc_i2c_bus *i2c_bus, u8 chip,
temp |= I2CR_MTX | I2CR_TX_NO_AK;
writeb(temp, base + (I2CR << reg_shift));
- /* write slave address */
- ret = tx_byte(i2c_bus, chip << 1);
- if (ret < 0)
- return ret;
-
- while (alen--) {
- ret = tx_byte(i2c_bus, (addr >> (alen * 8)) & 0xff);
+ if (alen >= 0) {
+ /* write slave address */
+ ret = tx_byte(i2c_bus, chip << 1);
if (ret < 0)
return ret;
+
+ while (alen--) {
+ ret = tx_byte(i2c_bus, (addr >> (alen * 8)) & 0xff);
+ if (ret < 0)
+ return ret;
+ }
}
+
return 0;
}
@@ -537,9 +540,11 @@ static int bus_i2c_read(struct mxc_i2c_bus *i2c_bus, u8 chip, u32 addr,
if (ret < 0)
return ret;
- temp = readb(base + (I2CR << reg_shift));
- temp |= I2CR_RSTA;
- writeb(temp, base + (I2CR << reg_shift));
+ if (alen >= 0) {
+ temp = readb(base + (I2CR << reg_shift));
+ temp |= I2CR_RSTA;
+ writeb(temp, base + (I2CR << reg_shift));
+ }
ret = tx_byte(i2c_bus, (chip << 1) | 1);
if (ret < 0) {
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 2/7] ext4: recover from filesystem corruption when reading
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 1/7] imx: mxc_i2c: tweak the i2c transfer method Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53 Martyn Welch
` (4 subsequent siblings)
6 siblings, 0 replies; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
From: Ian Ray <ian.ray@ge.com>
Some fixes when reading EXT files and directory entries were identified
after using e2fuzz to corrupt an EXT3 filesystem:
- Stop reading directory entries if the offset becomes badly aligned.
- Avoid overwriting memory by clamping the length used to zero the buffer
in ext4fs_read_file. Also sanity check blocksize.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
---
fs/ext4/ext4_common.c | 10 ++++++++++
fs/ext4/ext4fs.c | 10 +++++++++-
2 files changed, 19 insertions(+), 1 deletion(-)
diff --git a/fs/ext4/ext4_common.c b/fs/ext4/ext4_common.c
index 31952f4..dac9545 100644
--- a/fs/ext4/ext4_common.c
+++ b/fs/ext4/ext4_common.c
@@ -660,6 +660,11 @@ static int search_dir(struct ext2_inode *parent_inode, char *dirname)
offset = 0;
do {
+ if (offset & 3) {
+ printf("Badly aligned ext2_dirent\n");
+ break;
+ }
+
dir = (struct ext2_dirent *)(block_buffer + offset);
direntname = (char*)(dir) + sizeof(struct ext2_dirent);
@@ -880,6 +885,11 @@ static int unlink_filename(char *filename, unsigned int blknr)
offset = 0;
do {
+ if (offset & 3) {
+ printf("Badly aligned ext2_dirent\n");
+ break;
+ }
+
previous_dir = dir;
dir = (struct ext2_dirent *)(block_buffer + offset);
direntname = (char *)(dir) + sizeof(struct ext2_dirent);
diff --git a/fs/ext4/ext4fs.c b/fs/ext4/ext4fs.c
index b0c7303..9ee2caf 100644
--- a/fs/ext4/ext4fs.c
+++ b/fs/ext4/ext4fs.c
@@ -64,6 +64,9 @@ int ext4fs_read_file(struct ext2fs_node *node, loff_t pos,
char *delayed_buf = NULL;
short status;
+ if (blocksize <= 0)
+ return -1;
+
/* Adjust len so it we can't read past the end of the file. */
if (len + pos > filesize)
len = (filesize - pos);
@@ -127,6 +130,7 @@ int ext4fs_read_file(struct ext2fs_node *node, loff_t pos,
(blockend >> log2blksz);
}
} else {
+ int n;
if (previous_block_number != -1) {
/* spill */
status = ext4fs_devread(delayed_start,
@@ -137,7 +141,11 @@ int ext4fs_read_file(struct ext2fs_node *node, loff_t pos,
return -1;
previous_block_number = -1;
}
- memset(buf, 0, blocksize - skipfirst);
+ /* Zero no more than `len' bytes. */
+ n = blocksize - skipfirst;
+ if (n > len)
+ n = len;
+ memset(buf, 0, n);
}
buf += blocksize - skipfirst;
}
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 1/7] imx: mxc_i2c: tweak the i2c transfer method Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 2/7] ext4: recover from filesystem corruption when reading Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 15:31 ` Stefano Babic
2017-11-01 14:23 ` [U-Boot] [PATCH v3 4/7] arm: mx5: Add more register definitions Martyn Welch
` (3 subsequent siblings)
6 siblings, 1 reply; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
Add missing parts for i.MX53 PWM support
Acked-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
---
arch/arm/include/asm/arch-mx5/imx-regs.h | 19 +++++++++++++++++++
drivers/pwm/pwm-imx-util.c | 2 ++
2 files changed, 21 insertions(+)
diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
index 3e79fa3..c2ff798 100644
--- a/arch/arm/include/asm/arch-mx5/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
@@ -508,6 +508,25 @@ struct fuse_bank4_regs {
};
#endif
+#if defined(CONFIG_MX53)
+#define PWMCR_PRESCALER(x) (((x - 1) & 0xFFF) << 4)
+#define PWMCR_DOZEEN (1 << 24)
+#define PWMCR_WAITEN (1 << 23)
+#define PWMCR_DBGEN (1 << 22)
+#define PWMCR_CLKSRC_IPG_HIGH (2 << 16)
+#define PWMCR_CLKSRC_IPG (1 << 16)
+#define PWMCR_EN (1 << 0)
+
+struct pwm_regs {
+ u32 cr;
+ u32 sr;
+ u32 ir;
+ u32 sar;
+ u32 pr;
+ u32 cnr;
+};
+#endif
+
#endif /* __ASSEMBLER__*/
#endif /* __ASM_ARCH_MX5_IMX_REGS_H__ */
diff --git a/drivers/pwm/pwm-imx-util.c b/drivers/pwm/pwm-imx-util.c
index 534dd8e..97ac0c8 100644
--- a/drivers/pwm/pwm-imx-util.c
+++ b/drivers/pwm/pwm-imx-util.c
@@ -23,10 +23,12 @@ struct pwm_regs *pwm_id_to_reg(int pwm_id)
return (struct pwm_regs *)PWM1_BASE_ADDR;
case 1:
return (struct pwm_regs *)PWM2_BASE_ADDR;
+#ifdef CONFIG_MX6
case 2:
return (struct pwm_regs *)PWM3_BASE_ADDR;
case 3:
return (struct pwm_regs *)PWM4_BASE_ADDR;
+#endif
#ifdef CONFIG_MX6SX
case 4:
return (struct pwm_regs *)PWM5_BASE_ADDR;
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 4/7] arm: mx5: Add more register definitions
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
` (2 preceding siblings ...)
2017-11-01 14:23 ` [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53 Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 15:33 ` Stefano Babic
2017-11-01 14:23 ` [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem Martyn Welch
` (2 subsequent siblings)
6 siblings, 1 reply; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
Add register definitions require for video configuration.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
---
arch/arm/include/asm/arch-mx5/crm_regs.h | 9 +++++++++
arch/arm/include/asm/arch-mx5/imx-regs.h | 28 ++++++++++++++++++++++++++++
2 files changed, 37 insertions(+)
diff --git a/arch/arm/include/asm/arch-mx5/crm_regs.h b/arch/arm/include/asm/arch-mx5/crm_regs.h
index b61c7b9..c0af832 100644
--- a/arch/arm/include/asm/arch-mx5/crm_regs.h
+++ b/arch/arm/include/asm/arch-mx5/crm_regs.h
@@ -210,6 +210,15 @@ struct mxc_ccm_reg {
#define MXC_CCM_CSCMR1_SSI_EXT2_COM_CLK_SEL (0x1 << 1)
#define MXC_CCM_CSCMR1_SSI_EXT1_COM_CLK_SEL 0x1
+/* Define the bits in register CSCMR2 */
+#define MXC_CCM_CSCMR2_DI0_CLK_SEL_OFFSET 26
+#define MXC_CCM_CSCMR2_DI0_CLK_SEL_MASK (0x7 << 26)
+#define MXC_CCM_CSCMR2_DI0_CLK_SEL(v) (((v) & 0x7) << 26)
+#define MXC_CCM_CSCMR2_DI0_CLK_SEL_RD(r) (((r) >> 26) & 0x7)
+
+#define MXC_CCM_CSCMR2_DI0_CLK_SEL_LDB_DI0_CLK 5
+
+
/* Define the bits in register CSCDR2 */
#define MXC_CCM_CSCDR2_CSPI_CLK_PRED_OFFSET 25
#define MXC_CCM_CSCDR2_CSPI_CLK_PRED_MASK (0x7 << 25)
diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
index c2ff798..60c1bb9 100644
--- a/arch/arm/include/asm/arch-mx5/imx-regs.h
+++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
@@ -416,6 +416,34 @@ struct iomuxc {
};
#endif
+
+#define IOMUXC_GPR2_BITMAP_SPWG 0
+#define IOMUXC_GPR2_BITMAP_JEIDA 1
+
+#define IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET 6
+#define IOMUXC_GPR2_BIT_MAPPING_CH0_MASK (1<<IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET)
+#define IOMUXC_GPR2_BIT_MAPPING_CH0_JEIDA (IOMUXC_GPR2_BITMAP_JEIDA<<IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET)
+#define IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG (IOMUXC_GPR2_BITMAP_SPWG<<IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET)
+
+#define IOMUXC_GPR2_DATA_WIDTH_18 0
+#define IOMUXC_GPR2_DATA_WIDTH_24 1
+
+#define IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET 5
+#define IOMUXC_GPR2_DATA_WIDTH_CH0_MASK (1<<IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET)
+#define IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT (IOMUXC_GPR2_DATA_WIDTH_18<<IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET)
+#define IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT (IOMUXC_GPR2_DATA_WIDTH_24<<IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET)
+
+#define IOMUXC_GPR2_MODE_DISABLED 0
+#define IOMUXC_GPR2_MODE_ENABLED_DI0 1
+#define IOMUXC_GPR2_MODE_ENABLED_DI1 3
+
+#define IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET 0
+#define IOMUXC_GPR2_LVDS_CH0_MODE_MASK (3<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
+#define IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED (IOMUXC_GPR2_MODE_DISABLED<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
+#define IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 (IOMUXC_GPR2_MODE_ENABLED_DI0<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
+#define IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI1 (IOMUXC_GPR2_MODE_ENABLED_DI1<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
+
+
/* System Reset Controller (SRC) */
struct src {
u32 scr;
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
` (3 preceding siblings ...)
2017-11-01 14:23 ` [U-Boot] [PATCH v3 4/7] arm: mx5: Add more register definitions Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 14:41 ` Tom Rini
2017-11-01 15:28 ` Stefano Babic
2017-11-01 14:23 ` [U-Boot] [PATCH v3 6/7] rtc: add support for s35392a Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD Martyn Welch
6 siblings, 2 replies; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
From: Ian Ray <ian.ray@ge.com>
Add support for bootcounter on an EXT filesystem.
Sync configuration whitelist.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
---
Changes for v2:
- Adding Kconfig for EXT bootcount.
Changes for v3:
- Add over-arching BOOTCOUNT Kconfig entry.
README | 7 +++++
drivers/Kconfig | 2 ++
drivers/bootcount/Kconfig | 57 +++++++++++++++++++++++++++++++++++++
drivers/bootcount/Makefile | 1 +
drivers/bootcount/bootcount_ext.c | 59 +++++++++++++++++++++++++++++++++++++++
5 files changed, 126 insertions(+)
create mode 100644 drivers/bootcount/Kconfig
create mode 100644 drivers/bootcount/bootcount_ext.c
diff --git a/README b/README
index f288176..6336c5c 100644
--- a/README
+++ b/README
@@ -2362,6 +2362,13 @@ The following options need to be configured:
CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
the bootcounter.
CONFIG_BOOTCOUNT_ALEN = address len
+ CONFIG_BOOTCOUNT_EXT
+ enable support for the bootcounter in EXT filesystem
+ CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
+ and write.
+ CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
+ CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
+ CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 613e602..c2e813f 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -10,6 +10,8 @@ source "drivers/ata/Kconfig"
source "drivers/block/Kconfig"
+source "drivers/bootcount/Kconfig"
+
source "drivers/clk/Kconfig"
source "drivers/cpu/Kconfig"
diff --git a/drivers/bootcount/Kconfig b/drivers/bootcount/Kconfig
new file mode 100644
index 0000000..acffbcf
--- /dev/null
+++ b/drivers/bootcount/Kconfig
@@ -0,0 +1,57 @@
+#
+# Boot count configuration
+#
+
+menu "Boot count support"
+
+config BOOTCOUNT
+ bool "Enable Boot count support"
+ help
+ Enable boot count support, which provides the ability to store the
+ number of times the board has booted on a number of different
+ persistent storage mediums.
+
+if BOOTCOUNT
+
+config BOOTCOUNT_EXT
+ bool "Boot counter on EXT filesystem"
+ help
+ Add support for bootcounter on an EXT filesystem.
+
+if BOOTCOUNT_EXT
+
+config SYS_BOOTCOUNT_EXT_INTERFACE
+ string "Interface on which to find boot counter EXT filesystem"
+ default "mmc"
+ depends on BOOTCOUNT_EXT
+ help
+ Set the interface to use when locating the filesystem to use for the
+ boot counter.
+
+config SYS_BOOTCOUNT_EXT_DEVPART
+ string "Partition of the boot counter EXT filesystem"
+ default "0:1"
+ depends on BOOTCOUNT_EXT
+ help
+ Set the partition to use when locating the filesystem to use for the
+ boot counter.
+
+config SYS_BOOTCOUNT_EXT_NAME
+ string "Path and filename of the EXT filesystem based boot counter"
+ default "/boot/failures"
+ depends on BOOTCOUNT_EXT
+ help
+ Set the filename and path of the file used to store the boot counter.
+
+config SYS_BOOTCOUNT_ADDR
+ hex "RAM address used for reading and writing the boot counter"
+ default 0x7000A000
+ depends on BOOTCOUNT_EXT
+ help
+ Set the address used for reading and writing the boot counter.
+
+endif
+
+endif
+
+endmenu
diff --git a/drivers/bootcount/Makefile b/drivers/bootcount/Makefile
index ed9659a..45445d2 100644
--- a/drivers/bootcount/Makefile
+++ b/drivers/bootcount/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_BOOTCOUNT_AM33XX) += bootcount_davinci.o
obj-$(CONFIG_BOOTCOUNT_RAM) += bootcount_ram.o
obj-$(CONFIG_BOOTCOUNT_ENV) += bootcount_env.o
obj-$(CONFIG_BOOTCOUNT_I2C) += bootcount_i2c.o
+obj-$(CONFIG_BOOTCOUNT_EXT) += bootcount_ext.o
diff --git a/drivers/bootcount/bootcount_ext.c b/drivers/bootcount/bootcount_ext.c
new file mode 100644
index 0000000..d36bb0e
--- /dev/null
+++ b/drivers/bootcount/bootcount_ext.c
@@ -0,0 +1,59 @@
+/*
+ * Copyright (c) 2017 General Electric Company. All rights reserved.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <bootcount.h>
+#include <fs.h>
+#include <mapmem.h>
+
+#define BC_MAGIC 0xbc
+
+void bootcount_store(ulong a)
+{
+ uint8_t *buf;
+ loff_t len;
+ int ret;
+
+ if (fs_set_blk_dev(CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE, CONFIG_SYS_BOOTCOUNT_EXT_DEVPART, FS_TYPE_EXT)) {
+ puts("Error selecting device\n");
+ return;
+ }
+
+ buf = map_sysmem(CONFIG_SYS_BOOTCOUNT_ADDR, 2);
+ buf[0] = BC_MAGIC;
+ buf[1] = (a & 0xff);
+ unmap_sysmem(buf);
+
+ ret = fs_write(CONFIG_SYS_BOOTCOUNT_EXT_NAME, CONFIG_SYS_BOOTCOUNT_ADDR, 0, 2, &len);
+ if (ret != 0) {
+ puts("Error storing bootcount\n");
+ }
+}
+
+ulong bootcount_load(void)
+{
+ uint8_t *buf;
+ loff_t len_read;
+ int ret;
+
+ if (fs_set_blk_dev(CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE, CONFIG_SYS_BOOTCOUNT_EXT_DEVPART, FS_TYPE_EXT)) {
+ puts("Error selecting device\n");
+ return 0;
+ }
+
+ ret = fs_read(CONFIG_SYS_BOOTCOUNT_EXT_NAME, CONFIG_SYS_BOOTCOUNT_ADDR, 0, 2, &len_read);
+ if (ret != 0 || len_read != 2) {
+ puts("Error loading bootcount\n");
+ return 0;
+ }
+
+ buf = map_sysmem(CONFIG_SYS_BOOTCOUNT_ADDR, 2);
+ if (buf[0] == BC_MAGIC) {
+ ret = buf[1];
+ }
+ unmap_sysmem(buf);
+
+ return ret;
+}
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 6/7] rtc: add support for s35392a
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
` (4 preceding siblings ...)
2017-11-01 14:23 ` [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD Martyn Welch
6 siblings, 0 replies; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
From: Nandor Han <nandor.han@ge.com>
Add support for S35392A RTC. The driver supports both U-Boot driver
models.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Heiko Schocher <hs@denx.de>
---
drivers/rtc/Kconfig | 6 +
drivers/rtc/Makefile | 1 +
drivers/rtc/s35392a.c | 360 ++++++++++++++++++++++++++++++++++++++++++++++++++
lib/Kconfig | 3 +
4 files changed, 370 insertions(+)
create mode 100644 drivers/rtc/s35392a.c
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index d06130c7..2964bb2 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -30,4 +30,10 @@ config RTC_DS1307
Support for Dallas Semiconductor (now Maxim) DS1307 and DS1338/9 and
compatible Real Time Clock devices.
+config RTC_S35392A
+ bool "Enable S35392A driver"
+ select BITREVERSE
+ help
+ Enable s35392a driver which provides rtc get and set function.
+
endmenu
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 003e31a..7a8f97a 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -49,5 +49,6 @@ obj-$(CONFIG_RTC_RS5C372A) += rs5c372.o
obj-$(CONFIG_RTC_RV3029) += rv3029.o
obj-$(CONFIG_RTC_RX8025) += rx8025.o
obj-$(CONFIG_RTC_S3C24X0) += s3c24x0_rtc.o
+obj-$(CONFIG_RTC_S35392A) += s35392a.o
obj-$(CONFIG_SANDBOX) += sandbox_rtc.o
obj-$(CONFIG_RTC_X1205) += x1205.o
diff --git a/drivers/rtc/s35392a.c b/drivers/rtc/s35392a.c
new file mode 100644
index 0000000..0aa7865
--- /dev/null
+++ b/drivers/rtc/s35392a.c
@@ -0,0 +1,360 @@
+/*
+ * SII Semiconductor Corporation S35392A RTC driver.
+ *
+ * Copyright (c) 2017, General Electric Company
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+
+#include <command.h>
+#include <common.h>
+#include <dm.h>
+#include <i2c.h>
+#include <linux/bitrev.h>
+#include <rtc.h>
+
+#define S35390A_CMD_STATUS1 0x30
+#define S35390A_CMD_STATUS2 0x31
+#define S35390A_CMD_TIME1 0x32
+#define S35390A_CMD_TIME2 0x33
+#define S35390A_CMD_INT2_REG1 0x35
+
+#define S35390A_BYTE_YEAR 0
+#define S35390A_BYTE_MONTH 1
+#define S35390A_BYTE_DAY 2
+#define S35390A_BYTE_WDAY 3
+#define S35390A_BYTE_HOURS 4
+#define S35390A_BYTE_MINS 5
+#define S35390A_BYTE_SECS 6
+
+/* flags for STATUS1 */
+#define S35390A_FLAG_POC 0x01
+#define S35390A_FLAG_BLD 0x02
+#define S35390A_FLAG_INT2 0x04
+#define S35390A_FLAG_24H 0x40
+#define S35390A_FLAG_RESET 0x80
+
+/* If either BLD or POC is set, then the chip has lost power long enough for
+ * the time value to become invalid. */
+#define S35390A_LOW_VOLTAGE (S35390A_FLAG_POC | S35390A_FLAG_BLD)
+
+/*---------------------------------------------------------------------*/
+#undef DEBUG_RTC
+
+#ifdef DEBUG_RTC
+#define DEBUGR(fmt,args...) printf(fmt ,##args)
+#else
+#define DEBUGR(fmt,args...)
+#endif
+/*---------------------------------------------------------------------*/
+
+#ifdef CONFIG_DM_RTC
+#define DEV_TYPE struct udevice
+
+#else
+/* Local udevice */
+struct ludevice {
+ u8 chip;
+};
+#define DEV_TYPE struct ludevice
+struct ludevice dev;
+
+#endif
+
+#define msleep(a) udelay(a * 1000)
+
+int lowvoltage = 0;
+
+static int s35392a_rtc_reset(DEV_TYPE *dev);
+
+static int s35392a_rtc_read(DEV_TYPE *dev, u8 reg, u8* buf, int len)
+{
+ int ret;
+
+#ifdef CONFIG_DM_RTC
+ /* TODO: we need to tweak the chip address to reg */
+ ret = dm_i2c_read(dev, 0, buf, len);
+#else
+ (void)dev;
+ ret = i2c_read(reg, 0, -1, buf, len);
+#endif
+
+ return ret;
+}
+
+static int s35392a_rtc_write(DEV_TYPE *dev, u8 reg, u8* buf, int len)
+{
+ int ret;
+
+#ifdef CONFIG_DM_RTC
+ /* TODO: we need to tweak the chip address to reg */
+ ret = dm_i2c_write(dev, 0, buf, 1);
+#else
+ (void)dev;
+ ret = i2c_write(reg, 0, 0, buf, len);
+#endif
+
+ return ret;
+}
+
+static int s35392a_rtc_read8(DEV_TYPE *dev, unsigned int reg)
+{
+ u8 val;
+ int ret;
+
+ ret = s35392a_rtc_read(dev, reg, &val, sizeof(val));
+ return ret < 0 ? ret : val;
+}
+
+static int s35392a_rtc_write8(DEV_TYPE *dev, unsigned int reg, int val)
+{
+ int ret;
+ u8 lval = val;
+
+ ret = s35392a_rtc_write(dev, reg, &lval, sizeof(lval));
+ return ret < 0 ? ret : 0;
+}
+
+static int validate_time(const struct rtc_time *tm)
+{
+ if ((tm->tm_year < 2000) || (tm->tm_year > 2099))
+ return -EINVAL;
+
+ if ((tm->tm_mon < 1) || (tm->tm_mon > 12))
+ return -EINVAL;
+
+ if ((tm->tm_mday < 1) || (tm->tm_mday > 31))
+ return -EINVAL;
+
+ if ((tm->tm_wday < 0) || (tm->tm_wday > 6))
+ return -EINVAL;
+
+ if ((tm->tm_hour < 0) || (tm->tm_hour > 23))
+ return -EINVAL;
+
+ if ((tm->tm_min < 0) || (tm->tm_min > 59))
+ return -EINVAL;
+
+ if ((tm->tm_sec < 0) || (tm->tm_sec > 59))
+ return -EINVAL;
+
+ return 0;
+}
+
+void s35392a_rtc_init(DEV_TYPE *dev)
+{
+ int status = s35392a_rtc_read8(dev, S35390A_CMD_STATUS1);
+ if (status < 0)
+ goto error;
+
+ DEBUGR("init: S35390A_CMD_STATUS1: 0x%x\n", status);
+
+ lowvoltage = status & S35390A_LOW_VOLTAGE ? 1 : 0;
+
+ if (status & S35390A_FLAG_POC)
+ /*
+ * Do not communicate for 0.5 seconds since the power-on
+ * detection circuit is in operation.
+ */
+ msleep(500);
+
+ else if (!lowvoltage)
+ /*
+ * If both POC and BLD are unset everything is fine.
+ */
+ return;
+
+ if(lowvoltage)
+ printf("RTC low voltage detected\n");
+
+ if (!s35392a_rtc_reset(dev))
+ return;
+
+error:
+ printf("Error RTC init. \n");
+}
+
+/* Get the current time from the RTC */
+static int s35392a_rtc_get(DEV_TYPE *dev, struct rtc_time *tm)
+{
+ u8 date[7];
+ int ret, i;
+
+ if (lowvoltage) {
+ DEBUGR("RTC low voltage detected\n");
+ return -EINVAL;
+ }
+
+ ret = s35392a_rtc_read(dev, S35390A_CMD_TIME1, date, sizeof(date));
+ if (ret < 0) {
+ DEBUGR("Error reading date from RTC\n");
+ return -EIO;
+ }
+
+ /* This chip returns the bits of each byte in reverse order */
+ for (i = 0; i < 7; ++i)
+ date[i] = bitrev8(date[i]);
+
+ tm->tm_sec = bcd2bin(date[S35390A_BYTE_SECS]);
+ tm->tm_min = bcd2bin(date[S35390A_BYTE_MINS]);
+ tm->tm_hour = bcd2bin(date[S35390A_BYTE_HOURS] & ~S35390A_FLAG_24H);
+ tm->tm_wday = bcd2bin(date[S35390A_BYTE_WDAY]);
+ tm->tm_mday = bcd2bin(date[S35390A_BYTE_DAY]);
+ tm->tm_mon = bcd2bin(date[S35390A_BYTE_MONTH]);
+ tm->tm_year = bcd2bin(date[S35390A_BYTE_YEAR]) + 2000;
+
+ DEBUGR ("Get DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
+ tm->tm_year, tm->tm_mon, tm->tm_mday, tm->tm_wday,
+ tm->tm_hour, tm->tm_min, tm->tm_sec);
+
+ return 0;
+}
+
+/* Set the RTC */
+static int s35392a_rtc_set(DEV_TYPE *dev, const struct rtc_time *tm)
+{
+ int i, ret;
+ int status;
+ u8 date[7];
+
+ DEBUGR ("Set DATE: %4d-%02d-%02d (wday=%d) TIME: %2d:%02d:%02d\n",
+ tm->tm_year, tm->tm_mon, tm->tm_mday, tm->tm_wday,
+ tm->tm_hour, tm->tm_min, tm->tm_sec);
+
+ ret = validate_time(tm);
+ if (ret < 0)
+ return -EINVAL;
+
+ /* We support only 24h mode */
+ ret = s35392a_rtc_read8(dev, S35390A_CMD_STATUS1);
+ if (ret < 0)
+ return -EIO;
+ status = ret;
+
+ ret = s35392a_rtc_write8(dev, S35390A_CMD_STATUS1, status | S35390A_FLAG_24H);
+ if (ret < 0)
+ return -EIO;
+
+ date[S35390A_BYTE_YEAR] = bin2bcd(tm->tm_year - 2000);
+ date[S35390A_BYTE_MONTH] = bin2bcd(tm->tm_mon );
+ date[S35390A_BYTE_DAY] = bin2bcd(tm->tm_mday);
+ date[S35390A_BYTE_WDAY] = bin2bcd(tm->tm_wday);
+ date[S35390A_BYTE_HOURS] = bin2bcd(tm->tm_hour);
+ date[S35390A_BYTE_MINS] = bin2bcd(tm->tm_min);
+ date[S35390A_BYTE_SECS] = bin2bcd(tm->tm_sec);
+
+ /* This chip expects the bits of each byte to be in reverse order */
+ for (i = 0; i < 7; ++i)
+ date[i] = bitrev8(date[i]);
+
+ ret = s35392a_rtc_write(dev, S35390A_CMD_TIME1, date, sizeof(date));
+ if (ret < 0) {
+ DEBUGR("Error writing date to RTC\n");
+ return -EIO;
+ }
+
+ /* Now we have time. Reset the low voltage status */
+ lowvoltage = 0;
+
+ return 0;
+}
+
+/* Reset the RTC. */
+static int s35392a_rtc_reset(DEV_TYPE *dev)
+{
+ int buf;
+ int ret;
+ unsigned initcount = 0;
+
+ buf = S35390A_FLAG_RESET;
+
+initialize:
+ ret = s35392a_rtc_write8(dev, S35390A_CMD_STATUS1, buf);
+ if (ret < 0)
+ return -EIO;
+
+ ret = s35392a_rtc_read8(dev, S35390A_CMD_STATUS1);
+ if (ret < 0)
+ return -EIO;
+ buf = ret;
+
+ if (!lowvoltage)
+ lowvoltage = buf & S35390A_LOW_VOLTAGE ? 1 : 0;
+
+ if (buf & S35390A_LOW_VOLTAGE) {
+ /* Try up to five times to reset the chip */
+ if (initcount < 5) {
+ ++initcount;
+ goto initialize;
+ } else
+ return -EIO;
+ }
+
+ return 0;
+}
+
+#ifndef CONFIG_DM_RTC
+
+int rtc_get(struct rtc_time * tm)
+{
+ return s35392a_rtc_get(&dev, tm);
+}
+
+int rtc_set(struct rtc_time * tm)
+{
+ return s35392a_rtc_set(&dev, tm);
+}
+
+void rtc_reset(void)
+{
+ s35392a_rtc_reset(&dev);
+}
+
+void rtc_init(void)
+{
+ s35392a_rtc_init(&dev);
+}
+
+#else
+
+static int s35392a_probe(struct udevice *dev)
+{
+ s35392a_rtc_init(dev);
+ return 0;
+}
+
+static const struct rtc_ops s35392a_rtc_ops = {
+ .get = s35392a_rtc_get,
+ .set = s35392a_rtc_set,
+ .read8 = s35392a_rtc_read8,
+ .write8 = s35392a_rtc_write8,
+ .reset = s35392a_rtc_reset,
+};
+
+static const struct udevice_id s35392a_rtc_ids[] = {
+ { .compatible = "sii,s35392a-rtc" },
+ { }
+};
+
+U_BOOT_DRIVER(s35392a_rtc) = {
+ .name = "s35392a_rtc",
+ .id = UCLASS_RTC,
+ .probe = s35392a_probe,
+ .of_match = s35392a_rtc_ids,
+ .ops = &s35392a_rtc_ops,
+};
+
+#endif
diff --git a/lib/Kconfig b/lib/Kconfig
index 18663ba..f447c53 100644
--- a/lib/Kconfig
+++ b/lib/Kconfig
@@ -80,6 +80,9 @@ config TPL_TINY_MEMSET
config RBTREE
bool
+config BITREVERSE
+ bool "Bit reverse library from Linux"
+
source lib/dhry/Kconfig
menu "Security support"
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
` (5 preceding siblings ...)
2017-11-01 14:23 ` [U-Boot] [PATCH v3 6/7] rtc: add support for s35392a Martyn Welch
@ 2017-11-01 14:23 ` Martyn Welch
2017-11-01 15:53 ` Stefano Babic
6 siblings, 1 reply; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 14:23 UTC (permalink / raw)
To: u-boot
From: Peter Senna Tschudin <peter.senna@collabora.com>
Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
---
Changes for v2:
- Replacing boot count related defines with default config.
Changes for v3:
- Update config due to BOOTCOUNT Kconfig addition.
arch/arm/include/asm/mach-types.h | 1 +
arch/arm/mach-imx/mx5/Kconfig | 5 +
board/freescale/mx53ppd/Kconfig | 17 ++
board/freescale/mx53ppd/MAINTAINERS | 7 +
board/freescale/mx53ppd/Makefile | 12 +
board/freescale/mx53ppd/imximage.cfg | 87 ++++++
board/freescale/mx53ppd/mx53ppd.c | 487 ++++++++++++++++++++++++++++++++
board/freescale/mx53ppd/mx53ppd_video.c | 123 ++++++++
board/freescale/mx53ppd/ppd_gpio.h | 96 +++++++
board/freescale/mx53ppd/vpd_reader.c | 230 +++++++++++++++
board/freescale/mx53ppd/vpd_reader.h | 25 ++
configs/mx53ppd_defconfig | 39 +++
include/configs/mx53ppd.h | 246 ++++++++++++++++
13 files changed, 1375 insertions(+)
create mode 100644 board/freescale/mx53ppd/Kconfig
create mode 100644 board/freescale/mx53ppd/MAINTAINERS
create mode 100644 board/freescale/mx53ppd/Makefile
create mode 100644 board/freescale/mx53ppd/imximage.cfg
create mode 100644 board/freescale/mx53ppd/mx53ppd.c
create mode 100644 board/freescale/mx53ppd/mx53ppd_video.c
create mode 100644 board/freescale/mx53ppd/ppd_gpio.h
create mode 100644 board/freescale/mx53ppd/vpd_reader.c
create mode 100644 board/freescale/mx53ppd/vpd_reader.h
create mode 100644 configs/mx53ppd_defconfig
create mode 100644 include/configs/mx53ppd.h
diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h
index 9f82efe..2a257cc 100644
--- a/arch/arm/include/asm/mach-types.h
+++ b/arch/arm/include/asm/mach-types.h
@@ -5057,4 +5057,5 @@
#define MACH_TYPE_NASM25 5112
#define MACH_TYPE_TOMATO 5113
#define MACH_TYPE_OMAP3_MRC3D 5114
+#define MACH_TYPE_MX53_PPD 5134
#endif
diff --git a/arch/arm/mach-imx/mx5/Kconfig b/arch/arm/mach-imx/mx5/Kconfig
index ef37c35..330101d 100644
--- a/arch/arm/mach-imx/mx5/Kconfig
+++ b/arch/arm/mach-imx/mx5/Kconfig
@@ -45,6 +45,10 @@ config TARGET_MX53LOCO
select BOARD_LATE_INIT
select MX53
+config TARGET_MX53PPD
+ bool "Support mx53ppd"
+ select MX53
+
config TARGET_MX53SMD
bool "Support mx53smd"
select MX53
@@ -69,6 +73,7 @@ source "board/freescale/mx51evk/Kconfig"
source "board/freescale/mx53ard/Kconfig"
source "board/freescale/mx53evk/Kconfig"
source "board/freescale/mx53loco/Kconfig"
+source "board/freescale/mx53ppd/Kconfig"
source "board/freescale/mx53smd/Kconfig"
source "board/inversepath/usbarmory/Kconfig"
source "board/technologic/ts4800/Kconfig"
diff --git a/board/freescale/mx53ppd/Kconfig b/board/freescale/mx53ppd/Kconfig
new file mode 100644
index 0000000..c66d6a7
--- /dev/null
+++ b/board/freescale/mx53ppd/Kconfig
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+if TARGET_MX53PPD
+
+config SYS_BOARD
+ default "mx53ppd"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "mx5"
+
+config SYS_CONFIG_NAME
+ default "mx53ppd"
+
+endif
diff --git a/board/freescale/mx53ppd/MAINTAINERS b/board/freescale/mx53ppd/MAINTAINERS
new file mode 100644
index 0000000..9b64b5d
--- /dev/null
+++ b/board/freescale/mx53ppd/MAINTAINERS
@@ -0,0 +1,7 @@
+MX53PPD BOARD
+M: Antti Mäentausta <antti.maentausta@ge.com>
+M: Martyn Welch <martyn.welch@collabora.co.uk>
+S: Maintained
+F: board/freescale/mx53ppd/
+F: include/configs/mx53ppd.h
+F: configs/mx53ppd_defconfig
diff --git a/board/freescale/mx53ppd/Makefile b/board/freescale/mx53ppd/Makefile
new file mode 100644
index 0000000..df6c61f
--- /dev/null
+++ b/board/freescale/mx53ppd/Makefile
@@ -0,0 +1,12 @@
+# Copyright 2017 General Electric Company
+#
+# Based on board/freescale/mx53loco/Makefile:
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+# Jason Liu <r64343@freescale.com>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += mx53ppd.o vpd_reader.o
+obj-$(CONFIG_VIDEO) += mx53ppd_video.o
diff --git a/board/freescale/mx53ppd/imximage.cfg b/board/freescale/mx53ppd/imximage.cfg
new file mode 100644
index 0000000..83ff4b8
--- /dev/null
+++ b/board/freescale/mx53ppd/imximage.cfg
@@ -0,0 +1,87 @@
+/*
+ * Copyright 2017 General Electric Company
+ *
+ * Based on board/freescale/mx53loco/imximage.cfg:
+ *
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+BOOT_FROM sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+DATA 4 0x53fa8004 0x00194005
+DATA 4 0x53fa8554 0x00300000
+DATA 4 0x53fa8558 0x00300040
+DATA 4 0x53fa8560 0x00300000
+DATA 4 0x53fa8564 0x00300040
+DATA 4 0x53fa8568 0x00300040
+DATA 4 0x53fa8570 0x00300000
+DATA 4 0x53fa8574 0x00300000
+DATA 4 0x53fa8578 0x00300000
+DATA 4 0x53fa857c 0x00300040
+DATA 4 0x53fa8580 0x00300040
+DATA 4 0x53fa8584 0x00300000
+DATA 4 0x53fa8588 0x00300000
+DATA 4 0x53fa8590 0x00300040
+DATA 4 0x53fa8594 0x00300000
+DATA 4 0x53fa86f0 0x00300000
+DATA 4 0x53fa86f4 0x00000000
+DATA 4 0x53fa86fc 0x00000000
+DATA 4 0x53fa8714 0x00000000
+DATA 4 0x53fa8718 0x00300000
+DATA 4 0x53fa871c 0x00300000
+DATA 4 0x53fa8720 0x00300000
+DATA 4 0x53fa8728 0x00300000
+DATA 4 0x53fa872c 0x00300000
+DATA 4 0x63fd9088 0x35343535
+DATA 4 0x63fd9090 0x4d444c44
+DATA 4 0x63fd907c 0x01370138
+DATA 4 0x63fd9080 0x013b013c
+DATA 4 0x63fd9018 0x00111740
+DATA 4 0x63fd9000 0x85190000
+DATA 4 0x63fd900c 0x8b8f52e3
+DATA 4 0x63fd9010 0xb68e8a63
+DATA 4 0x63fd9014 0x01ff00db
+DATA 4 0x63fd902c 0x000026d2
+DATA 4 0x63fd9030 0x008f0e21
+DATA 4 0x63fd9008 0x09333030
+DATA 4 0x63fd9004 0x0002002d
+DATA 4 0x63fd901c 0x00008032
+DATA 4 0x63fd901c 0x00008033
+DATA 4 0x63fd901c 0x00468031
+DATA 4 0x63fd901c 0x052080b0
+DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd901c 0x0000803a
+DATA 4 0x63fd901c 0x0000803b
+DATA 4 0x63fd901c 0x00028039
+DATA 4 0x63fd901c 0x05208138
+DATA 4 0x63fd901c 0x04008048
+DATA 4 0x63fd9020 0x00005800
+DATA 4 0x63fd9040 0x05380003
+DATA 4 0x63fd9058 0x00011110
+DATA 4 0x63fd901c 0x00000000
diff --git a/board/freescale/mx53ppd/mx53ppd.c b/board/freescale/mx53ppd/mx53ppd.c
new file mode 100644
index 0000000..8c26f27
--- /dev/null
+++ b/board/freescale/mx53ppd/mx53ppd.c
@@ -0,0 +1,487 @@
+/*
+ * Copyright 2017 General Electric Company
+ *
+ * Based on board/freescale/mx53loco/mx53loco.c:
+ *
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux-mx53.h>
+#include <asm/arch/clock.h>
+#include <linux/errno.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/mach-imx/mx5_video.h>
+#include <netdev.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/gpio.h>
+#include <power/pmic.h>
+#include <dialog_pmic.h>
+#include <fsl_pmic.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <watchdog.h>
+#include "ppd_gpio.h"
+#include <stdlib.h>
+#include "vpd_reader.h"
+#include <rtc.h>
+
+#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Index of I2C1, SEGMENT 1 (see CONFIG_SYS_I2C_BUSES). */
+#define VPD_EEPROM_BUS 2
+
+/* Address of 24C08 EEPROM. */
+#define VPD_EEPROM_ADDR 0x50
+#define VPD_EEPROM_ADDR_LEN 1
+
+static uint32_t mx53_dram_size[2];
+
+phys_size_t get_effective_memsize(void)
+{
+ /*
+ * WARNING: We must override get_effective_memsize() function here
+ * to report only the size of the first DRAM bank. This is to make
+ * U-Boot relocator place U-Boot into valid memory, that is, at the
+ * end of the first DRAM bank. If we did not override this function
+ * like so, U-Boot would be placed at the address of the first DRAM
+ * bank + total DRAM size - sizeof(uboot), which in the setup where
+ * each DRAM bank contains 512MiB of DRAM would result in placing
+ * U-Boot into invalid memory area close to the end of the first
+ * DRAM bank.
+ */
+ return mx53_dram_size[0];
+}
+
+int dram_init(void)
+{
+ mx53_dram_size[0] = get_ram_size((void *)PHYS_SDRAM_1, 1 << 30);
+ mx53_dram_size[1] = get_ram_size((void *)PHYS_SDRAM_2, 1 << 30);
+
+ gd->ram_size = mx53_dram_size[0] + mx53_dram_size[1];
+
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+ gd->bd->bi_dram[0].size = mx53_dram_size[0];
+
+ gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
+ gd->bd->bi_dram[1].size = mx53_dram_size[1];
+
+ return 0;
+}
+
+u32 get_board_rev(void)
+{
+ struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
+ struct fuse_bank *bank = &iim->bank[0];
+ struct fuse_bank0_regs *fuse =
+ (struct fuse_bank0_regs *)bank->fuse_regs;
+
+ int rev = readl(&fuse->gp[6]);
+
+ rev = 0;
+
+ return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
+}
+
+#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+
+#ifdef CONFIG_USB_EHCI_MX5
+int board_ehci_hcd_init(int port)
+{
+ /* request VBUS power enable pin, GPIO7_8 */
+ imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
+ gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
+ return 0;
+}
+#endif
+
+static void setup_iomux_fec(void)
+{
+ static const iomux_v3_cfg_t fec_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
+ PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
+ NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
+ PAD_CTL_HYS | PAD_CTL_PKE),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg esdhc_cfg[2] = {
+ {MMC_SDHC3_BASE_ADDR},
+ {MMC_SDHC1_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return 1;
+}
+
+#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP)
+#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_DSE_HIGH)
+
+int board_mmc_init(bd_t *bis)
+{
+ static const iomux_v3_cfg_t sd1_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
+ SD_CMD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
+ MX53_PAD_EIM_DA11__GPIO3_11,
+ };
+
+ static const iomux_v3_cfg_t sd2_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
+ MX53_PAD_EIM_DA13__GPIO3_13,
+ };
+
+ u32 index;
+ int ret;
+
+ esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+
+ for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
+ switch (index) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(sd1_pads,
+ ARRAY_SIZE(sd1_pads));
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(sd2_pads,
+ ARRAY_SIZE(sd2_pads));
+ break;
+ default:
+ printf("Warning: you configured more ESDHC controller"
+ "(%d) as supported by the board(2)\n",
+ CONFIG_SYS_FSL_ESDHC_NUM);
+ return -EINVAL;
+ }
+ ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+#endif
+
+#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
+
+static void setup_iomux_i2c(void)
+{
+ static const iomux_v3_cfg_t i2c1_pads[] = {
+ NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
+ };
+
+ imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads));
+}
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX53_PAD_EIM_D21__I2C1_SCL | I2C_PAD,
+ .gpio_mode = MX53_PAD_EIM_D28__GPIO3_28 | I2C_PAD,
+ .gp = IMX_GPIO_NR(3, 28)
+ },
+ .sda = {
+ .i2c_mode = MX53_PAD_EIM_D28__I2C1_SDA | I2C_PAD,
+ .gpio_mode = MX53_PAD_EIM_D21__GPIO3_21 | I2C_PAD,
+ .gp = IMX_GPIO_NR(3, 21)
+ }
+};
+
+static void clock_1GHz(void)
+{
+ int ret;
+ u32 ref_clk = MXC_HCLK;
+ /*
+ * After increasing voltage to 1.25V, we can switch
+ * CPU clock to 1GHz and DDR to 400MHz safely
+ */
+ ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
+ if (ret)
+ printf("CPU: Switch CPU clock to 1GHZ failed\n");
+
+ ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
+ ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
+ if (ret)
+ printf("CPU: Switch DDR clock to 400MHz failed\n");
+}
+
+void ppd_gpio_init(void)
+{
+ int i;
+ imx_iomux_v3_setup_multiple_pads(ppd_pads, ARRAY_SIZE(ppd_pads));
+ for (i = 0; i < ARRAY_SIZE(ppd_gpios); ++i) {
+ gpio_direction_output(ppd_gpios[i].gpio, ppd_gpios[i].value);
+ }
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_fec();
+ setup_iomux_lcd();
+ ppd_gpio_init();
+
+ return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
+#define VPD_TYPE_INVALID 0x00
+#define VPD_BLOCK_NETWORK 0x20
+#define VPD_BLOCK_HWID 0x44
+#define VPD_PRODUCT_PPD 4
+#define VPD_HAS_MAC1 0x1
+#define VPD_MAC_ADDRESS_LENGTH 6
+
+struct vpd_cache {
+ uint8_t product_id;
+ uint8_t has;
+ unsigned char mac1[VPD_MAC_ADDRESS_LENGTH];
+};
+
+/*
+ * Extracts MAC and product information from the VPD.
+ */
+static int vpd_callback(
+ void *userdata,
+ uint8_t id,
+ uint8_t version,
+ uint8_t type,
+ size_t size,
+ uint8_t const *data)
+{
+ struct vpd_cache *vpd = (struct vpd_cache *)userdata;
+
+ if ( id == VPD_BLOCK_HWID
+ && version == 1
+ && type != VPD_TYPE_INVALID
+ && size >= 1) {
+ vpd->product_id = data[0];
+
+ } else if ( id == VPD_BLOCK_NETWORK
+ && version == 1
+ && type != VPD_TYPE_INVALID) {
+ if (size >= 6) {
+ vpd->has |= VPD_HAS_MAC1;
+ memcpy(vpd->mac1, data, VPD_MAC_ADDRESS_LENGTH);
+ }
+ }
+
+ return 0;
+}
+
+static void process_vpd(struct vpd_cache *vpd)
+{
+ int fec_index = -1;
+
+ switch (vpd->product_id)
+ {
+ case VPD_PRODUCT_PPD:
+ fec_index = 0;
+ break;
+ }
+
+ if (fec_index >= 0 && (vpd->has & VPD_HAS_MAC1)) {
+ eth_env_set_enetaddr("ethaddr", vpd->mac1);
+ }
+}
+
+static int read_vpd(uint eeprom_bus)
+{
+ struct vpd_cache vpd;
+ int res;
+ int size = 1024;
+ uint8_t *data;
+ unsigned int current_i2c_bus = i2c_get_bus_num();
+
+ res = i2c_set_bus_num(eeprom_bus);
+ if (res < 0)
+ return res;
+
+ data = (uint8_t *)malloc(size);
+ if (!data)
+ return -ENOMEM;
+
+ res = i2c_read(VPD_EEPROM_ADDR, 0,
+ VPD_EEPROM_ADDR_LEN, data, size);
+
+ if (res == 0) {
+ memset(&vpd, 0, sizeof(vpd));
+ vpd_reader(size, data, &vpd, vpd_callback);
+ process_vpd(&vpd);
+ }
+
+ free(data);
+
+ i2c_set_bus_num(current_i2c_bus);
+ return res;
+}
+
+void check_time(void)
+{
+ int ret, i;
+ struct rtc_time tm;
+ u8 retry = 3;
+
+ unsigned int current_i2c_bus = i2c_get_bus_num();
+
+ ret = i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM);
+ if (ret < 0)
+ return;
+
+ rtc_init();
+
+ for (i = 0; i < retry; i++) {
+ ret = rtc_get(&tm);
+ if(!ret || ret == -EINVAL) {
+ break;
+ }
+ }
+
+ if (ret < 0) {
+ env_set("rtc_status", "RTC_ERROR");
+ }
+
+ if (tm.tm_year > 2037) {
+ tm.tm_sec = 0;
+ tm.tm_min = 0;
+ tm.tm_hour = 0;
+ tm.tm_mday = 1;
+ tm.tm_wday = 2;
+ tm.tm_mon = 1;
+ tm.tm_year = 2036;
+
+ for (i = 0; i < retry; i++) {
+ ret = rtc_set(&tm);
+ if(!ret) {
+ break;
+ }
+ }
+
+ if (ret < 0)
+ env_set("rtc_status", "RTC_ERROR");
+ }
+
+ i2c_set_bus_num(current_i2c_bus);
+}
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ mxc_set_sata_internal_clock();
+ setup_iomux_i2c();
+
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ const char *cause;
+
+ /* We care about WDOG only, treating everything else as
+ * a power-on-reset.
+ */
+ if (get_imx_reset_cause() & 0x0010) {
+ cause = "WDOG";
+ } else {
+ cause = "POR";
+ }
+
+ env_set("bootcause", cause);
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ read_vpd(VPD_EEPROM_BUS);
+
+ clock_1GHz();
+ print_cpuinfo();
+ hw_watchdog_init();
+
+ check_time();
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: GE PPD\n");
+
+ return 0;
+}
+
+static int do_lcd_enable(cmd_tbl_t *cmdtp, int flag, int argc,
+ char * const argv[])
+{
+ lcd_enable();
+ return 0;
+}
+
+U_BOOT_CMD(
+ ppd_lcd_enable, 1, 1, do_lcd_enable,
+ "enable PPD LCD",
+ "no parameters"
+);
diff --git a/board/freescale/mx53ppd/mx53ppd_video.c b/board/freescale/mx53ppd/mx53ppd_video.c
new file mode 100644
index 0000000..338f00f
--- /dev/null
+++ b/board/freescale/mx53ppd/mx53ppd_video.c
@@ -0,0 +1,123 @@
+/*
+ * Copyright 2017 General Electric Company
+ *
+ * Based on board/freescale/mx53loco/mx53loco_video.c:
+ *
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ * Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/list.h>
+#include <asm/gpio.h>
+#include <asm/arch/iomux-mx53.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/io.h>
+#include <pwm.h>
+#include "ppd_gpio.h"
+
+#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
+
+static struct fb_videomode const nv_spwg = {
+ .name = "NV-SPWGRGB888",
+ .refresh = 60,
+ .xres = 800,
+ .yres = 480,
+ .pixclock = 15384,
+ .left_margin = 16,
+ .right_margin = 210,
+ .upper_margin = 10,
+ .lower_margin = 22,
+ .hsync_len = 30,
+ .vsync_len = 13,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED
+};
+
+
+void setup_iomux_lcd(void)
+{
+ static const iomux_v3_cfg_t lcd_pads[] = {
+ MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
+ MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
+ MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
+ MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
+ MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
+ MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
+ MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
+ MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
+ MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
+ MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
+ MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
+ MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
+ MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
+ MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
+ MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
+ MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
+ MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
+ MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
+ MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
+ MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
+ MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
+ MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
+ MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
+ MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
+ MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
+ MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
+ MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
+ MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
+ };
+
+ imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+}
+
+void lcd_enable(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* Set LDB_DI0 as clock source for IPU_DI0 */
+ clrsetbits_le32(&mxc_ccm->cscmr2,
+ MXC_CCM_CSCMR2_DI0_CLK_SEL_MASK,
+ MXC_CCM_CSCMR2_DI0_CLK_SEL(MXC_CCM_CSCMR2_DI0_CLK_SEL_LDB_DI0_CLK));
+
+ /* Turn on IPU LDB DI0 clocks */
+ setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_LDB_DI0(3));
+
+ /* Turn on IPU DI0 clocks */
+ setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_IPU_DI0(3));
+
+ /* Configure LDB */
+ writel(IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+ IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
+ IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
+ &iomux->gpr[2]);
+
+ /* Enable backlights */
+ pwm_init(1, 0, 0);
+
+ /* duty cycle 5000000ns, period: 5000000ns */
+ pwm_config(1, 5000000, 5000000);
+
+ /* Backlight Power */
+ gpio_direction_output(BACKLIGHT_ENABLE, 1);
+
+ pwm_enable(1);
+}
+
+
+int board_video_skip(void)
+{
+ int ret;
+
+ ret = ipuv3_fb_init(&nv_spwg, 0, IPU_PIX_FMT_RGB24);
+ if (ret)
+ printf("Display cannot be configured: %d\n", ret);
+
+ return ret;
+}
diff --git a/board/freescale/mx53ppd/ppd_gpio.h b/board/freescale/mx53ppd/ppd_gpio.h
new file mode 100644
index 0000000..a722435
--- /dev/null
+++ b/board/freescale/mx53ppd/ppd_gpio.h
@@ -0,0 +1,96 @@
+/*
+ * (C) Copyright 2015 General Electric Company
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PPD_GPIO_H_
+#define __PPD_GPIO_H_
+
+#include <asm/arch/iomux-mx53.h>
+#include <asm/gpio.h>
+
+#define PPD_UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
+ PAD_CTL_PUS_100K_UP)
+
+static const iomux_v3_cfg_t ppd_pads[] = {
+ /* FEC */
+ MX53_PAD_EIM_A22__GPIO2_16,
+ /* UART */
+ NEW_PAD_CTRL(MX53_PAD_PATA_DMACK__UART1_RXD_MUX, PPD_UART_PAD_CTRL),
+ NEW_PAD_CTRL(MX53_PAD_PATA_DIOW__UART1_TXD_MUX, PPD_UART_PAD_CTRL),
+ /* Video */
+ MX53_PAD_CSI0_DATA_EN__GPIO5_20, /* LR_SCAN_CTRL */
+ MX53_PAD_CSI0_VSYNC__GPIO5_21, /* UD_SCAN_CTRL */
+ MX53_PAD_CSI0_DAT10__GPIO5_28, /* DATA_WIDTH_CTRL */
+ MX53_PAD_CSI0_PIXCLK__GPIO5_18, /* HOST_CONTROLLED_RESET_TO_LCD_N */
+ MX53_PAD_EIM_DA2__GPIO3_2, /* LVDS1_MUX_CTRL */
+ MX53_PAD_EIM_DA3__GPIO3_3, /* LVDS0_MUX_CTRL */
+ MX53_PAD_EIM_A21__GPIO2_17, /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
+ MX53_PAD_CSI0_DAT11__GPIO5_29, /* BACKLIGHT_ENABLE */
+ MX53_PAD_DISP0_DAT9__PWM2_PWMO, /* IMX535_PWM2_TO_LCD_CONNECTOR */
+ /* I2C */
+ MX53_PAD_EIM_A20__GPIO2_18, /* RESET_I2C1_BUS_SEGMENT_MUX_N */
+
+ /* SPI */
+ MX53_PAD_DISP0_DAT23__GPIO5_17,
+ MX53_PAD_KEY_COL2__GPIO4_10,
+ MX53_PAD_KEY_ROW2__GPIO4_11,
+ MX53_PAD_KEY_COL3__GPIO4_12,
+};
+
+struct gpio_cfg {
+ unsigned gpio;
+ int value;
+};
+
+#define RESET_IMX535_ETHERNET_PHY_N IMX_GPIO_NR(2, 16)
+#define UD_SCAN_CTRL IMX_GPIO_NR(5, 21)
+#define LR_SCAN_CTRL IMX_GPIO_NR(5, 20)
+#define LVDS0_MUX_CTRL IMX_GPIO_NR(3, 3)
+#define LVDS1_MUX_CTRL IMX_GPIO_NR(3, 2)
+#define HOST_CONTROLLED_RESET_TO_LCD_N IMX_GPIO_NR(5, 18)
+#define DATA_WIDTH_CTRL IMX_GPIO_NR(5, 28)
+#define RESET_DP0_TRANSMITTER_N IMX_GPIO_NR(2, 28)
+#define RESET_DP1_TRANSMITTER_N IMX_GPIO_NR(2, 29)
+#define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22)
+#define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27)
+#define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17)
+#define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29)
+#define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18)
+#define ECSPI1_CS0 IMX_GPIO_NR(5, 17)
+#define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
+#define ECSPI1_CS2 IMX_GPIO_NR(4, 11)
+#define ECSPI1_CS3 IMX_GPIO_NR(4, 12)
+
+static const struct gpio_cfg ppd_gpios[] = {
+ /* FEC */
+ /* Drive Low as GPIO output for 25ms per Eth Phy IX spec */
+ /* Then Drive High as GPIO output to bring Eth Phy IC out of reset */
+ { RESET_IMX535_ETHERNET_PHY_N, 0 },
+ { RESET_IMX535_ETHERNET_PHY_N, 1 },
+ /* Video */
+ { UD_SCAN_CTRL, 0 },
+ { LR_SCAN_CTRL, 1 },
+#ifdef PROPRIETARY_CHANGES
+ { LVDS0_MUX_CTRL, 1 },
+#else
+ { LVDS0_MUX_CTRL, 0 },
+#endif
+ { LVDS1_MUX_CTRL, 1 },
+ { HOST_CONTROLLED_RESET_TO_LCD_N, 1 },
+ { DATA_WIDTH_CTRL, 0 },
+ { RESET_DP0_TRANSMITTER_N, 1 },
+ { RESET_DP1_TRANSMITTER_N, 1 },
+ { POWER_DOWN_LVDS0_DESERIALIZER_N, 1 },
+ { POWER_DOWN_LVDS1_DESERIALIZER_N, 1 },
+ { ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 },
+ { BACKLIGHT_ENABLE, 0 },
+ { RESET_I2C1_BUS_SEGMENT_MUX_N, 1 },
+ { ECSPI1_CS0, 1 },
+ { ECSPI1_CS1, 1 },
+ { ECSPI1_CS2, 1 },
+ { ECSPI1_CS3, 1 },
+};
+
+#endif /* __PPD_GPIO_H_ */
diff --git a/board/freescale/mx53ppd/vpd_reader.c b/board/freescale/mx53ppd/vpd_reader.c
new file mode 100644
index 0000000..ea6daf7
--- /dev/null
+++ b/board/freescale/mx53ppd/vpd_reader.c
@@ -0,0 +1,230 @@
+/*
+ * Copyright 2016 General Electric Company
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include "vpd_reader.h"
+
+#include <linux/bch.h>
+#include <stdlib.h>
+#include <errno.h>
+
+
+/* BCH configuration */
+
+const struct {
+ int header_ecc_capability_bits;
+ int data_ecc_capability_bits;
+ unsigned int prim_poly;
+ struct {
+ int min;
+ int max;
+ } galois_field_order;
+} bch_configuration = {
+ .header_ecc_capability_bits = 4,
+ .data_ecc_capability_bits = 16,
+ .prim_poly = 0,
+ .galois_field_order = {
+ .min = 5,
+ .max = 15,
+ },
+};
+
+static int calculate_galois_field_order(size_t source_length)
+{
+ int gfo = bch_configuration.galois_field_order.min;
+
+ for (; gfo < bch_configuration.galois_field_order.max &&
+ ((((1 << gfo) - 1) - ((int)source_length * 8)) < 0);
+ gfo++) {
+ }
+
+ if (gfo == bch_configuration.galois_field_order.max) {
+ return -1;
+ }
+
+ return gfo + 1;
+}
+
+static int verify_bch(int ecc_bits, unsigned int prim_poly,
+ uint8_t * data, size_t data_length,
+ const uint8_t * ecc, size_t ecc_length)
+{
+ int gfo = calculate_galois_field_order(data_length);
+ if (gfo < 0) {
+ return -1;
+ }
+
+ struct bch_control * bch = init_bch(gfo, ecc_bits, prim_poly);
+ if (!bch) {
+ return -1;
+ }
+
+ if (bch->ecc_bytes != ecc_length) {
+ free_bch(bch);
+ return -1;
+ }
+
+ unsigned * errloc = (unsigned *)calloc(data_length, sizeof(unsigned));
+ int errors = decode_bch(
+ bch, data, data_length, ecc, NULL, NULL, errloc);
+ free_bch(bch);
+ if (errors < 0) {
+ free(errloc);
+ return -1;
+ }
+
+ if (errors > 0) {
+ int n;
+ for (n = 0; n < errors; n++) {
+ if (errloc[n] >= 8 * data_length) {
+ /* n-th error located in ecc (no need for data correction) */
+ } else {
+ /* n-th error located in data */
+ data[errloc[n] / 8] ^= 1 << (errloc[n] % 8);
+ }
+ }
+ }
+
+ free(errloc);
+ return 0;
+}
+
+
+static const int ID = 0;
+static const int LEN = 1;
+static const int VER = 2;
+static const int TYP = 3;
+static const int BLOCK_SIZE = 4;
+
+static const uint8_t HEADER_BLOCK_ID = 0x00;
+static const uint8_t HEADER_BLOCK_LEN = 18;
+static const uint32_t HEADER_BLOCK_MAGIC = 0xca53ca53;
+static const size_t HEADER_BLOCK_VERIFY_LEN = 14;
+static const size_t HEADER_BLOCK_ECC_OFF = 14;
+static const size_t HEADER_BLOCK_ECC_LEN = 4;
+
+static const uint8_t ECC_BLOCK_ID = 0xFF;
+
+int vpd_reader(
+ size_t size,
+ uint8_t * data,
+ void * userdata,
+ int (*fn)(
+ void * userdata,
+ uint8_t id,
+ uint8_t version,
+ uint8_t type,
+ size_t size,
+ uint8_t const * data))
+{
+ if ( size < HEADER_BLOCK_LEN
+ || data == NULL
+ || fn == NULL) {
+ return -EINVAL;
+ }
+
+ /*
+ * +--------------------+--------------------+--//--+--------------------+
+ * | header block | data block | ... | ecc block |
+ * +--------------------+--------------------+--//--+--------------------+
+ * : : :
+ * +------+-------+-----+ +------+-------------+
+ * | id | magic | ecc | | ... | ecc |
+ * | len | off | | +------+-------------+
+ * | ver | size | | :
+ * | type | | | :
+ * +------+-------+-----+ :
+ * : : : :
+ * <----- [1] ----> <----------- [2] ----------->
+ *
+ * Repair (if necessary) the contents of header block [1] by using a
+ * 4 byte ECC located at the end of the header block. A successful
+ * return value means that we can trust the header.
+ */
+ int ret = verify_bch(
+ bch_configuration.header_ecc_capability_bits,
+ bch_configuration.prim_poly,
+ data,
+ HEADER_BLOCK_VERIFY_LEN,
+ &data[HEADER_BLOCK_ECC_OFF],
+ HEADER_BLOCK_ECC_LEN);
+ if (ret < 0) {
+ return ret;
+ }
+
+ /* Validate header block { id, length, version, type }. */
+ if ( data[ID] != HEADER_BLOCK_ID
+ || data[LEN] != HEADER_BLOCK_LEN
+ || data[VER] != 0
+ || data[TYP] != 0
+ || ntohl(*(uint32_t *)(&data[4])) != HEADER_BLOCK_MAGIC) {
+ return -EINVAL;
+ }
+
+ uint32_t offset = ntohl(*(uint32_t *)(&data[8]));
+ uint16_t size_bits = ntohs(*(uint16_t *)(&data[12]));
+
+ /* Check that ECC header fits. */
+ if (offset + 3 >= size) {
+ return -EINVAL;
+ }
+
+ /* Validate ECC block. */
+ uint8_t * ecc = &data[offset];
+ if ( ecc[ID] != ECC_BLOCK_ID
+ || ecc[LEN] < BLOCK_SIZE
+ || ecc[LEN] + offset > size
+ || ecc[LEN] - BLOCK_SIZE != size_bits / 8
+ || ecc[VER] != 1
+ || ecc[TYP] != 1) {
+ return -EINVAL;
+ }
+
+ /*
+ * Use the header block to locate the ECC block and verify the data
+ * blocks [2] against the ecc block ECC.
+ */
+ ret = verify_bch(
+ bch_configuration.data_ecc_capability_bits,
+ bch_configuration.prim_poly,
+ &data[data[LEN]],
+ offset - data[LEN],
+ &data[offset + BLOCK_SIZE],
+ ecc[LEN] - BLOCK_SIZE);
+ if (ret < 0) {
+ return ret;
+ }
+
+ /* Stop after ECC. Ignore possible zero padding. */
+ size = offset;
+
+ for (;;) {
+ /* Move to next block. */
+ size -= data[LEN];
+ data += data[LEN];
+
+ if (size == 0) {
+ /* Finished iterating through blocks. */
+ return 0;
+ }
+
+ if ( size < BLOCK_SIZE
+ || data[LEN] < BLOCK_SIZE) {
+ /* Not enough data for a header, or short header. */
+ return -EINVAL;
+ }
+
+ ret = fn(
+ userdata,
+ data[ID],
+ data[VER],
+ data[TYP],
+ data[LEN] - BLOCK_SIZE,
+ &data[BLOCK_SIZE]);
+ if (ret) {
+ return ret;
+ }
+ }
+}
diff --git a/board/freescale/mx53ppd/vpd_reader.h b/board/freescale/mx53ppd/vpd_reader.h
new file mode 100644
index 0000000..efa172a
--- /dev/null
+++ b/board/freescale/mx53ppd/vpd_reader.h
@@ -0,0 +1,25 @@
+/*
+ * Copyright 2016 General Electric Company
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include "common.h"
+
+/*
+ * Read VPD from given data, verify content, and call callback
+ * for each vital product data block.
+ *
+ * Returns Non-zero on error. Negative numbers encode errno.
+ */
+int vpd_reader(
+ size_t size,
+ uint8_t * data,
+ void * userdata,
+ int (*fn)(
+ void * userdata,
+ uint8_t id,
+ uint8_t version,
+ uint8_t type,
+ size_t size,
+ uint8_t const * data));
diff --git a/configs/mx53ppd_defconfig b/configs/mx53ppd_defconfig
new file mode 100644
index 0000000..1cc3578
--- /dev/null
+++ b/configs/mx53ppd_defconfig
@@ -0,0 +1,39 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX5=y
+CONFIG_TARGET_MX53PPD=y
+CONFIG_FIT=y
+CONFIG_BOOTCOUNT=y
+CONFIG_BOOTCOUNT_EXT=y
+CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE="mmc"
+CONFIG_SYS_BOOTCOUNT_EXT_DEVPART="0:5"
+CONFIG_SYS_BOOTCOUNT_EXT_NAME="/boot/failures"
+CONFIG_SYS_BOOTCOUNT_ADDR=0x7000A000
+CONFIG_NETDEVICES=y
+CONFIG_VIDEO=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53ppd/imximage.cfg"
+CONFIG_BOOTDELAY=1
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_I2C=y
+CONFIG_RTC_S35392A=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+# CONFIG_VIDEO_SW_CURSOR is not set
+CONFIG_OF_LIBFDT=y
+
+CONFIG_MMC=y
diff --git a/include/configs/mx53ppd.h b/include/configs/mx53ppd.h
new file mode 100644
index 0000000..59cc527
--- /dev/null
+++ b/include/configs/mx53ppd.h
@@ -0,0 +1,246 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * Configuration settings for Freescale MX53 low cost board.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MACH_TYPE MACH_TYPE_MX53_PPD
+
+#include <asm/arch/imx-regs.h>
+
+#define CONSOLE_DEV "ttymxc0"
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_SYS_FSL_CLK
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS 8000
+
+#define CONFIG_MISC_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+#define CONFIG_REVISION_TAG
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_ESDHC_NUM 2
+
+#define CONFIG_SUPPORT_RAW_INITRD /* bootz raw initrd support */
+
+/* Eth Configs */
+#define CONFIG_MII
+
+#define CONFIG_FEC_MXC
+#define IMX_FEC_BASE FEC_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x1F
+
+/* USB Configs */
+#define CONFIG_USB_EHCI_MX5
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_MXC_USB_PORT 1
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+
+#define CONFIG_SYS_RTC_BUS_NUM 2
+#define CONFIG_SYS_I2C_RTC_ADDR 0x30
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+
+/* PMIC Controller */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_DIALOG_POWER
+#define CONFIG_POWER_FSL
+#define CONFIG_POWER_FSL_MC13892
+#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
+#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Command definition */
+#define CONFIG_SUPPORT_RAW_INITRD
+
+
+#define CONFIG_ETHPRIME "FEC0"
+
+#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
+#define CONFIG_SYS_TEXT_BASE 0x77800000
+
+#define PPD_CONFIG_NFS \
+ "nfsserver=192.168.252.95\0" \
+ "gatewayip=192.168.252.95\0" \
+ "netmask=255.255.255.0\0" \
+ "ipaddr=192.168.252.99\0" \
+ "kernsize=0x2000\0" \
+ "use_dhcp=0\0" \
+ "nfsroot=/opt/springdale/rd\0" \
+ "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs ${kern_ipconf} nfsroot=${nfsserver}:${nfsroot},v3,tcp rw\0" \
+ "choose_ip=if test $use_dhcp = 1; then set kern_ipconf ip=dhcp; set getcmd dhcp; else set kern_ipconf ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off; set getcmd tftp; fi\0" \
+ "nfs=run choose_ip setargs bootargs_nfs; ${getcmd} ${loadaddr} ${nfsserver}:${image}; bootm ${loadaddr}\0" \
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ PPD_CONFIG_NFS \
+ "bootlimit=10\0" \
+ "image=/boot/fitImage\0" \
+ "fdt_high=0xffffffff\0" \
+ "dev=mmc\0" \
+ "devnum=0\0" \
+ "rootdev=mmcblk0p\0" \
+ "quiet=quiet loglevel=0\0" \
+ "console=" CONSOLE_DEV "\0" \
+ "lvds=ldb\0" \
+ "setargs=setenv bootargs ${lvds} jtag=on mem=2G vt.global_cursor_default=0 " \
+ "bootcause=${bootcause} " \
+ "${quiet} console=${console} ${rtc_status}" \
+ "\0" \
+ "bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} " \
+ "ro rootwait ${bootargs}\0" \
+ "doquiet=" \
+ "if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; then setenv quiet; fi\0" \
+ "hasfirstboot=" \
+ "ext2load ${dev} ${devnum}:${partnum} 0x7000A000 /boot/bootcause/firstboot\0" \
+ "swappartitions=" \
+ "setexpr partnum 3 - ${partnum}\0" \
+ "failbootcmd=" \
+ "ppd_lcd_enable; " \
+ "msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
+ "echo $msg; " \
+ "setenv stdout vga; " \
+ "echo \"\n\n\n\n \" $msg; " \
+ "setenv stdout serial; " \
+ "mw.b 0x7000A000 0xbc; " \
+ "mw.b 0x7000A001 0x00; " \
+ "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+ "altbootcmd=" \
+ "run doquiet; " \
+ "setenv partnum 1; run hasfirstboot || setenv partnum 2; run hasfirstboot || setenv partnum 0; " \
+ "if test ${partnum} != 0; then " \
+ "setenv bootcause REVERT; " \
+ "run swappartitions loadimage doboot; " \
+ "fi; " \
+ "run failbootcmd\0" \
+ "loadimage=" \
+ "ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
+ "doboot=" \
+ "echo Booting from ${dev}:${devnum}:${partnum} ...; " \
+ "run setargs; " \
+ "run bootargs_emmc; " \
+ "bootm ${loadaddr}\0" \
+ "tryboot=" \
+ "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
+ "run loadimage || run swappartitions && run loadimage || setenv partnum 0 && echo MISSING IMAGE;" \
+ "run doboot; " \
+ "run failbootcmd\0" \
+ "video-mode=" \
+ "lcd:800x480-24 at 60,monitor=lcd\0" \
+
+
+#define CONFIG_MMCBOOTCOMMAND \
+ "if mmc dev ${devnum}; then " \
+ "run doquiet; " \
+ "run tryboot; " \
+ "fi; " \
+
+#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+#define CONFIG_SYS_MAXARGS 48 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_SYS_MEMTEST_START 0x70000000
+#define CONFIG_SYS_MEMTEST_END 0x70010000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 2
+#define PHYS_SDRAM_1 CSD0_BASE_ADDR
+#define PHYS_SDRAM_1_SIZE (gd->bd->bi_dram[0].size)
+#define PHYS_SDRAM_2 CSD1_BASE_ADDR
+#define PHYS_SDRAM_2_SIZE (gd->bd->bi_dram[1].size)
+#define PHYS_SDRAM_SIZE (gd->ram_size)
+
+#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
+#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
+#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_CMD_FUSE
+#define CONFIG_FSL_IIM
+
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* I2C1 */
+#define CONFIG_SYS_NUM_I2C_BUSES 9
+#define CONFIG_SYS_I2C_MAX_HOPS 1
+#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
+ {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
+ }
+
+#define CONFIG_BCH
+
+#define CONFIG_BOOTCOUNT_LIMIT
+
+/* Backlight Control */
+#define CONFIG_PWM_IMX
+#define CONFIG_IMX6_PWM_PER_CLK 66666000
+
+/* Framebuffer and LCD */
+#ifdef CONFIG_VIDEO
+ #define CONFIG_VIDEO_IPUV3
+#endif
+
+#endif /* __CONFIG_H */
--
2.1.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem
2017-11-01 14:23 ` [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem Martyn Welch
@ 2017-11-01 14:41 ` Tom Rini
2017-11-01 15:28 ` Stefano Babic
1 sibling, 0 replies; 17+ messages in thread
From: Tom Rini @ 2017-11-01 14:41 UTC (permalink / raw)
To: u-boot
On Wed, Nov 01, 2017 at 02:23:07PM +0000, Martyn Welch wrote:
> From: Ian Ray <ian.ray@ge.com>
>
> Add support for bootcounter on an EXT filesystem.
> Sync configuration whitelist.
>
> Signed-off-by: Ian Ray <ian.ray@ge.com>
> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20171101/3344d1ce/attachment.sig>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem
2017-11-01 14:23 ` [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem Martyn Welch
2017-11-01 14:41 ` Tom Rini
@ 2017-11-01 15:28 ` Stefano Babic
2017-11-01 16:24 ` Tom Rini
1 sibling, 1 reply; 17+ messages in thread
From: Stefano Babic @ 2017-11-01 15:28 UTC (permalink / raw)
To: u-boot
Hi Martin, Ian,
On 01/11/2017 15:23, Martyn Welch wrote:
> From: Ian Ray <ian.ray@ge.com>
>
> Add support for bootcounter on an EXT filesystem.
> Sync configuration whitelist.
>
> Signed-off-by: Ian Ray <ian.ray@ge.com>
> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> ---
> Changes for v2:
> - Adding Kconfig for EXT bootcount.
>
> Changes for v3:
> - Add over-arching BOOTCOUNT Kconfig entry.
>
Should we better split this into two ? The patch patch does more as
commit message suggests. First, it moves bootcounter to Kconfig (first
topic). Second, it adds EXT support.
> README | 7 +++++
> drivers/Kconfig | 2 ++
> drivers/bootcount/Kconfig | 57 +++++++++++++++++++++++++++++++++++++
> drivers/bootcount/Makefile | 1 +
> drivers/bootcount/bootcount_ext.c | 59 +++++++++++++++++++++++++++++++++++++++
> 5 files changed, 126 insertions(+)
> create mode 100644 drivers/bootcount/Kconfig
> create mode 100644 drivers/bootcount/bootcount_ext.c
>
> diff --git a/README b/README
> index f288176..6336c5c 100644
> --- a/README
> +++ b/README
> @@ -2362,6 +2362,13 @@ The following options need to be configured:
> CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
> the bootcounter.
> CONFIG_BOOTCOUNT_ALEN = address len
> + CONFIG_BOOTCOUNT_EXT
> + enable support for the bootcounter in EXT filesystem
> + CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
> + and write.
> + CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
> + CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
> + CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename
>
> - Show boot progress:
> CONFIG_SHOW_BOOT_PROGRESS
> diff --git a/drivers/Kconfig b/drivers/Kconfig
> index 613e602..c2e813f 100644
> --- a/drivers/Kconfig
> +++ b/drivers/Kconfig
> @@ -10,6 +10,8 @@ source "drivers/ata/Kconfig"
>
> source "drivers/block/Kconfig"
>
> +source "drivers/bootcount/Kconfig"
> +
> source "drivers/clk/Kconfig"
>
> source "drivers/cpu/Kconfig"
> diff --git a/drivers/bootcount/Kconfig b/drivers/bootcount/Kconfig
> new file mode 100644
> index 0000000..acffbcf
> --- /dev/null
> +++ b/drivers/bootcount/Kconfig
> @@ -0,0 +1,57 @@
> +#
> +# Boot count configuration
> +#
> +
> +menu "Boot count support"
> +
> +config BOOTCOUNT
> + bool "Enable Boot count support"
> + help
> + Enable boot count support, which provides the ability to store the
> + number of times the board has booted on a number of different
> + persistent storage mediums.
> +
> +if BOOTCOUNT
> +
> +config BOOTCOUNT_EXT
> + bool "Boot counter on EXT filesystem"
> + help
> + Add support for bootcounter on an EXT filesystem.
> +
> +if BOOTCOUNT_EXT
> +
> +config SYS_BOOTCOUNT_EXT_INTERFACE
> + string "Interface on which to find boot counter EXT filesystem"
> + default "mmc"
> + depends on BOOTCOUNT_EXT
> + help
> + Set the interface to use when locating the filesystem to use for the
> + boot counter.
> +
> +config SYS_BOOTCOUNT_EXT_DEVPART
> + string "Partition of the boot counter EXT filesystem"
> + default "0:1"
> + depends on BOOTCOUNT_EXT
> + help
> + Set the partition to use when locating the filesystem to use for the
> + boot counter.
> +
> +config SYS_BOOTCOUNT_EXT_NAME
> + string "Path and filename of the EXT filesystem based boot counter"
> + default "/boot/failures"
> + depends on BOOTCOUNT_EXT
> + help
> + Set the filename and path of the file used to store the boot counter.
> +
> +config SYS_BOOTCOUNT_ADDR
> + hex "RAM address used for reading and writing the boot counter"
> + default 0x7000A000
> + depends on BOOTCOUNT_EXT
> + help
> + Set the address used for reading and writing the boot counter.
> +
> +endif
> +
> +endif
> +
> +endmenu
> diff --git a/drivers/bootcount/Makefile b/drivers/bootcount/Makefile
> index ed9659a..45445d2 100644
> --- a/drivers/bootcount/Makefile
> +++ b/drivers/bootcount/Makefile
> @@ -9,3 +9,4 @@ obj-$(CONFIG_BOOTCOUNT_AM33XX) += bootcount_davinci.o
> obj-$(CONFIG_BOOTCOUNT_RAM) += bootcount_ram.o
> obj-$(CONFIG_BOOTCOUNT_ENV) += bootcount_env.o
> obj-$(CONFIG_BOOTCOUNT_I2C) += bootcount_i2c.o
> +obj-$(CONFIG_BOOTCOUNT_EXT) += bootcount_ext.o
> diff --git a/drivers/bootcount/bootcount_ext.c b/drivers/bootcount/bootcount_ext.c
> new file mode 100644
> index 0000000..d36bb0e
> --- /dev/null
> +++ b/drivers/bootcount/bootcount_ext.c
> @@ -0,0 +1,59 @@
> +/*
> + * Copyright (c) 2017 General Electric Company. All rights reserved.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <bootcount.h>
> +#include <fs.h>
> +#include <mapmem.h>
> +
> +#define BC_MAGIC 0xbc
> +
> +void bootcount_store(ulong a)
> +{
> + uint8_t *buf;
> + loff_t len;
> + int ret;
> +
> + if (fs_set_blk_dev(CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE, CONFIG_SYS_BOOTCOUNT_EXT_DEVPART, FS_TYPE_EXT)) {
> + puts("Error selecting device\n");
> + return;
> + }
> +
> + buf = map_sysmem(CONFIG_SYS_BOOTCOUNT_ADDR, 2);
> + buf[0] = BC_MAGIC;
> + buf[1] = (a & 0xff);
> + unmap_sysmem(buf);
> +
> + ret = fs_write(CONFIG_SYS_BOOTCOUNT_EXT_NAME, CONFIG_SYS_BOOTCOUNT_ADDR, 0, 2, &len);
> + if (ret != 0) {
> + puts("Error storing bootcount\n");
> + }
> +}
> +
> +ulong bootcount_load(void)
> +{
> + uint8_t *buf;
> + loff_t len_read;
> + int ret;
> +
> + if (fs_set_blk_dev(CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE, CONFIG_SYS_BOOTCOUNT_EXT_DEVPART, FS_TYPE_EXT)) {
> + puts("Error selecting device\n");
> + return 0;
> + }
> +
> + ret = fs_read(CONFIG_SYS_BOOTCOUNT_EXT_NAME, CONFIG_SYS_BOOTCOUNT_ADDR, 0, 2, &len_read);
> + if (ret != 0 || len_read != 2) {
> + puts("Error loading bootcount\n");
> + return 0;
> + }
> +
> + buf = map_sysmem(CONFIG_SYS_BOOTCOUNT_ADDR, 2);
> + if (buf[0] == BC_MAGIC) {
> + ret = buf[1];
> + }
> + unmap_sysmem(buf);
> +
> + return ret;
> +}
No comment about the implementation, I just asking why we need a further
way for the bootcounter. IMHO the best way remains putting it into a
non-persistent storage (RAM / SOC), even if this has the drawback that
is SOC specific. I know there was a discussion about this. Near the RAM
option, there is the bootcounter in ENV, and this is SOC-unaware. Adding
further methods look to me just a work-around to not add u-boot ENV
utils in user space.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53
2017-11-01 14:23 ` [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53 Martyn Welch
@ 2017-11-01 15:31 ` Stefano Babic
2017-11-01 15:42 ` Martyn Welch
0 siblings, 1 reply; 17+ messages in thread
From: Stefano Babic @ 2017-11-01 15:31 UTC (permalink / raw)
To: u-boot
On 01/11/2017 15:23, Martyn Welch wrote:
> Add missing parts for i.MX53 PWM support
>
> Acked-by: Nandor Han <nandor.han@ge.com>
> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
> arch/arm/include/asm/arch-mx5/imx-regs.h | 19 +++++++++++++++++++
> drivers/pwm/pwm-imx-util.c | 2 ++
> 2 files changed, 21 insertions(+)
>
> diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
> index 3e79fa3..c2ff798 100644
> --- a/arch/arm/include/asm/arch-mx5/imx-regs.h
> +++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
> @@ -508,6 +508,25 @@ struct fuse_bank4_regs {
> };
> #endif
>
> +#if defined(CONFIG_MX53)
It looks to me this is not MX53 specific. You are already changing a MX5
file. As far as I see, this is valid at least for MX51. Do we need the
#ifdef ?
> +#define PWMCR_PRESCALER(x) (((x - 1) & 0xFFF) << 4)
> +#define PWMCR_DOZEEN (1 << 24)
> +#define PWMCR_WAITEN (1 << 23)
> +#define PWMCR_DBGEN (1 << 22)
> +#define PWMCR_CLKSRC_IPG_HIGH (2 << 16)
> +#define PWMCR_CLKSRC_IPG (1 << 16)
> +#define PWMCR_EN (1 << 0)
> +
> +struct pwm_regs {
> + u32 cr;
> + u32 sr;
> + u32 ir;
> + u32 sar;
> + u32 pr;
> + u32 cnr;
> +};
> +#endif
> +
> #endif /* __ASSEMBLER__*/
>
> #endif /* __ASM_ARCH_MX5_IMX_REGS_H__ */
> diff --git a/drivers/pwm/pwm-imx-util.c b/drivers/pwm/pwm-imx-util.c
> index 534dd8e..97ac0c8 100644
> --- a/drivers/pwm/pwm-imx-util.c
> +++ b/drivers/pwm/pwm-imx-util.c
> @@ -23,10 +23,12 @@ struct pwm_regs *pwm_id_to_reg(int pwm_id)
> return (struct pwm_regs *)PWM1_BASE_ADDR;
> case 1:
> return (struct pwm_regs *)PWM2_BASE_ADDR;
> +#ifdef CONFIG_MX6
> case 2:
> return (struct pwm_regs *)PWM3_BASE_ADDR;
> case 3:
> return (struct pwm_regs *)PWM4_BASE_ADDR;
> +#endif
> #ifdef CONFIG_MX6SX
> case 4:
> return (struct pwm_regs *)PWM5_BASE_ADDR;
>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 4/7] arm: mx5: Add more register definitions
2017-11-01 14:23 ` [U-Boot] [PATCH v3 4/7] arm: mx5: Add more register definitions Martyn Welch
@ 2017-11-01 15:33 ` Stefano Babic
0 siblings, 0 replies; 17+ messages in thread
From: Stefano Babic @ 2017-11-01 15:33 UTC (permalink / raw)
To: u-boot
Hi Martyn,
On 01/11/2017 15:23, Martyn Welch wrote:
> Add register definitions require for video configuration.
>
> Signed-off-by: Nandor Han <nandor.han@ge.com>
> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
> arch/arm/include/asm/arch-mx5/crm_regs.h | 9 +++++++++
> arch/arm/include/asm/arch-mx5/imx-regs.h | 28 ++++++++++++++++++++++++++++
> 2 files changed, 37 insertions(+)
>
> diff --git a/arch/arm/include/asm/arch-mx5/crm_regs.h b/arch/arm/include/asm/arch-mx5/crm_regs.h
> index b61c7b9..c0af832 100644
> --- a/arch/arm/include/asm/arch-mx5/crm_regs.h
> +++ b/arch/arm/include/asm/arch-mx5/crm_regs.h
> @@ -210,6 +210,15 @@ struct mxc_ccm_reg {
> #define MXC_CCM_CSCMR1_SSI_EXT2_COM_CLK_SEL (0x1 << 1)
> #define MXC_CCM_CSCMR1_SSI_EXT1_COM_CLK_SEL 0x1
>
> +/* Define the bits in register CSCMR2 */
> +#define MXC_CCM_CSCMR2_DI0_CLK_SEL_OFFSET 26
> +#define MXC_CCM_CSCMR2_DI0_CLK_SEL_MASK (0x7 << 26)
> +#define MXC_CCM_CSCMR2_DI0_CLK_SEL(v) (((v) & 0x7) << 26)
> +#define MXC_CCM_CSCMR2_DI0_CLK_SEL_RD(r) (((r) >> 26) & 0x7)
> +
> +#define MXC_CCM_CSCMR2_DI0_CLK_SEL_LDB_DI0_CLK 5
> +
> +
> /* Define the bits in register CSCDR2 */
> #define MXC_CCM_CSCDR2_CSPI_CLK_PRED_OFFSET 25
> #define MXC_CCM_CSCDR2_CSPI_CLK_PRED_MASK (0x7 << 25)
> diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
> index c2ff798..60c1bb9 100644
> --- a/arch/arm/include/asm/arch-mx5/imx-regs.h
> +++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
> @@ -416,6 +416,34 @@ struct iomuxc {
> };
> #endif
>
> +
> +#define IOMUXC_GPR2_BITMAP_SPWG 0
> +#define IOMUXC_GPR2_BITMAP_JEIDA 1
> +
> +#define IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET 6
> +#define IOMUXC_GPR2_BIT_MAPPING_CH0_MASK (1<<IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET)
> +#define IOMUXC_GPR2_BIT_MAPPING_CH0_JEIDA (IOMUXC_GPR2_BITMAP_JEIDA<<IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET)
> +#define IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG (IOMUXC_GPR2_BITMAP_SPWG<<IOMUXC_GPR2_BIT_MAPPING_CH0_OFFSET)
> +
> +#define IOMUXC_GPR2_DATA_WIDTH_18 0
> +#define IOMUXC_GPR2_DATA_WIDTH_24 1
> +
> +#define IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET 5
> +#define IOMUXC_GPR2_DATA_WIDTH_CH0_MASK (1<<IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET)
> +#define IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT (IOMUXC_GPR2_DATA_WIDTH_18<<IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET)
> +#define IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT (IOMUXC_GPR2_DATA_WIDTH_24<<IOMUXC_GPR2_DATA_WIDTH_CH0_OFFSET)
> +
> +#define IOMUXC_GPR2_MODE_DISABLED 0
> +#define IOMUXC_GPR2_MODE_ENABLED_DI0 1
> +#define IOMUXC_GPR2_MODE_ENABLED_DI1 3
> +
> +#define IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET 0
> +#define IOMUXC_GPR2_LVDS_CH0_MODE_MASK (3<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
> +#define IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED (IOMUXC_GPR2_MODE_DISABLED<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
> +#define IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 (IOMUXC_GPR2_MODE_ENABLED_DI0<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
> +#define IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI1 (IOMUXC_GPR2_MODE_ENABLED_DI1<<IOMUXC_GPR2_LVDS_CH0_MODE_OFFSET)
> +
> +
> /* System Reset Controller (SRC) */
> struct src {
> u32 scr;
>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53
2017-11-01 15:31 ` Stefano Babic
@ 2017-11-01 15:42 ` Martyn Welch
2017-11-01 15:58 ` Stefano Babic
0 siblings, 1 reply; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 15:42 UTC (permalink / raw)
To: u-boot
On Wed, 2017-11-01 at 16:31 +0100, Stefano Babic wrote:
> On 01/11/2017 15:23, Martyn Welch wrote:
> > Add missing parts for i.MX53 PWM support
> >
> > Acked-by: Nandor Han <nandor.han@ge.com>
> > Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> > Cc: Stefano Babic <sbabic@denx.de>
> > ---
> > arch/arm/include/asm/arch-mx5/imx-regs.h | 19 +++++++++++++++++++
> > drivers/pwm/pwm-imx-util.c | 2 ++
> > 2 files changed, 21 insertions(+)
> >
> > diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
> > index 3e79fa3..c2ff798 100644
> > --- a/arch/arm/include/asm/arch-mx5/imx-regs.h
> > +++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
> > @@ -508,6 +508,25 @@ struct fuse_bank4_regs {
> > };
> > #endif
> >
> > +#if defined(CONFIG_MX53)
>
> It looks to me this is not MX53 specific. You are already changing a MX5
> file. As far as I see, this is valid at least for MX51. Do we need the
> #ifdef ?
>
I only have access to an MX53, I'm not familiar with the rest of the MX5
family and was thus playing it safe.
> > +#define PWMCR_PRESCALER(x) (((x - 1) & 0xFFF) << 4)
> > +#define PWMCR_DOZEEN (1 << 24)
> > +#define PWMCR_WAITEN (1 << 23)
> > +#define PWMCR_DBGEN (1 << 22)
> > +#define PWMCR_CLKSRC_IPG_HIGH (2 << 16)
> > +#define PWMCR_CLKSRC_IPG (1 << 16)
> > +#define PWMCR_EN (1 << 0)
> > +
> > +struct pwm_regs {
> > + u32 cr;
> > + u32 sr;
> > + u32 ir;
> > + u32 sar;
> > + u32 pr;
> > + u32 cnr;
> > +};
> > +#endif
> > +
> > #endif /* __ASSEMBLER__*/
> >
> > #endif /* __ASM_ARCH_MX5_IMX_REGS_H__ */
> > diff --git a/drivers/pwm/pwm-imx-util.c b/drivers/pwm/pwm-imx-util.c
> > index 534dd8e..97ac0c8 100644
> > --- a/drivers/pwm/pwm-imx-util.c
> > +++ b/drivers/pwm/pwm-imx-util.c
> > @@ -23,10 +23,12 @@ struct pwm_regs *pwm_id_to_reg(int pwm_id)
> > return (struct pwm_regs *)PWM1_BASE_ADDR;
> > case 1:
> > return (struct pwm_regs *)PWM2_BASE_ADDR;
> > +#ifdef CONFIG_MX6
> > case 2:
> > return (struct pwm_regs *)PWM3_BASE_ADDR;
> > case 3:
> > return (struct pwm_regs *)PWM4_BASE_ADDR;
> > +#endif
> > #ifdef CONFIG_MX6SX
> > case 4:
> > return (struct pwm_regs *)PWM5_BASE_ADDR;
> >
>
>
> Best regards,
> Stefano Babic
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD
2017-11-01 14:23 ` [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD Martyn Welch
@ 2017-11-01 15:53 ` Stefano Babic
2017-11-01 17:56 ` Martyn Welch
0 siblings, 1 reply; 17+ messages in thread
From: Stefano Babic @ 2017-11-01 15:53 UTC (permalink / raw)
To: u-boot
Hi Martyn, Peter,
On 01/11/2017 15:23, Martyn Welch wrote:
> From: Peter Senna Tschudin <peter.senna@collabora.com>
>
> Create board support for GE PPD, based on mx53loco.
>
> Use mx53ppd_defconfig make target to configure for this board.
>
> Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
> Signed-off-by: Ian Ray <ian.ray@ge.com>
> Signed-off-by: Nandor Han <nandor.han@ge.com>
> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> Cc: Stefano Babic <sbabic@denx.de>
> ---
> Changes for v2:
> - Replacing boot count related defines with default config.
>
> Changes for v3:
> - Update config due to BOOTCOUNT Kconfig addition.
>
> arch/arm/include/asm/mach-types.h | 1 +
> arch/arm/mach-imx/mx5/Kconfig | 5 +
> board/freescale/mx53ppd/Kconfig | 17 ++
> board/freescale/mx53ppd/MAINTAINERS | 7 +
> board/freescale/mx53ppd/Makefile | 12 +
> board/freescale/mx53ppd/imximage.cfg | 87 ++++++
> board/freescale/mx53ppd/mx53ppd.c | 487 ++++++++++++++++++++++++++++++++
> board/freescale/mx53ppd/mx53ppd_video.c | 123 ++++++++
> board/freescale/mx53ppd/ppd_gpio.h | 96 +++++++
> board/freescale/mx53ppd/vpd_reader.c | 230 +++++++++++++++
> board/freescale/mx53ppd/vpd_reader.h | 25 ++
> configs/mx53ppd_defconfig | 39 +++
> include/configs/mx53ppd.h | 246 ++++++++++++++++
> 13 files changed, 1375 insertions(+)
> create mode 100644 board/freescale/mx53ppd/Kconfig
> create mode 100644 board/freescale/mx53ppd/MAINTAINERS
> create mode 100644 board/freescale/mx53ppd/Makefile
> create mode 100644 board/freescale/mx53ppd/imximage.cfg
> create mode 100644 board/freescale/mx53ppd/mx53ppd.c
> create mode 100644 board/freescale/mx53ppd/mx53ppd_video.c
> create mode 100644 board/freescale/mx53ppd/ppd_gpio.h
> create mode 100644 board/freescale/mx53ppd/vpd_reader.c
> create mode 100644 board/freescale/mx53ppd/vpd_reader.h
> create mode 100644 configs/mx53ppd_defconfig
> create mode 100644 include/configs/mx53ppd.h
>
> diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h
> index 9f82efe..2a257cc 100644
> --- a/arch/arm/include/asm/mach-types.h
> +++ b/arch/arm/include/asm/mach-types.h
> @@ -5057,4 +5057,5 @@
> #define MACH_TYPE_NASM25 5112
> #define MACH_TYPE_TOMATO 5113
> #define MACH_TYPE_OMAP3_MRC3D 5114
> +#define MACH_TYPE_MX53_PPD 5134
Ouch..still an ancient Kernel ? 2.6.35, maybe ?
Even in that case, we agreed to not touch anymore mach-types.h. The
value should go into the board configuration file,
#define CONFIG_MACH_TYPE 5134
> #endif
> diff --git a/arch/arm/mach-imx/mx5/Kconfig b/arch/arm/mach-imx/mx5/Kconfig
> index ef37c35..330101d 100644
> --- a/arch/arm/mach-imx/mx5/Kconfig
> +++ b/arch/arm/mach-imx/mx5/Kconfig
> @@ -45,6 +45,10 @@ config TARGET_MX53LOCO
> select BOARD_LATE_INIT
> select MX53
>
> +config TARGET_MX53PPD
> + bool "Support mx53ppd"
> + select MX53
> +
> config TARGET_MX53SMD
> bool "Support mx53smd"
> select MX53
> @@ -69,6 +73,7 @@ source "board/freescale/mx51evk/Kconfig"
> source "board/freescale/mx53ard/Kconfig"
> source "board/freescale/mx53evk/Kconfig"
> source "board/freescale/mx53loco/Kconfig"
> +source "board/freescale/mx53ppd/Kconfig"
> source "board/freescale/mx53smd/Kconfig"
> source "board/inversepath/usbarmory/Kconfig"
> source "board/technologic/ts4800/Kconfig"
> diff --git a/board/freescale/mx53ppd/Kconfig b/board/freescale/mx53ppd/Kconfig
> new file mode 100644
> index 0000000..c66d6a7
> --- /dev/null
> +++ b/board/freescale/mx53ppd/Kconfig
> @@ -0,0 +1,17 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +
> +if TARGET_MX53PPD
> +
> +config SYS_BOARD
> + default "mx53ppd"
> +
> +config SYS_VENDOR
> + default "freescale"
> +
> +config SYS_SOC
> + default "mx5"
> +
> +config SYS_CONFIG_NAME
> + default "mx53ppd"
> +
> +endif
> diff --git a/board/freescale/mx53ppd/MAINTAINERS b/board/freescale/mx53ppd/MAINTAINERS
> new file mode 100644
> index 0000000..9b64b5d
> --- /dev/null
> +++ b/board/freescale/mx53ppd/MAINTAINERS
> @@ -0,0 +1,7 @@
> +MX53PPD BOARD
> +M: Antti Mäentausta <antti.maentausta@ge.com>
> +M: Martyn Welch <martyn.welch@collabora.co.uk>
> +S: Maintained
> +F: board/freescale/mx53ppd/
> +F: include/configs/mx53ppd.h
> +F: configs/mx53ppd_defconfig
> diff --git a/board/freescale/mx53ppd/Makefile b/board/freescale/mx53ppd/Makefile
> new file mode 100644
> index 0000000..df6c61f
> --- /dev/null
> +++ b/board/freescale/mx53ppd/Makefile
> @@ -0,0 +1,12 @@
> +# Copyright 2017 General Electric Company
> +#
> +# Based on board/freescale/mx53loco/Makefile:
> +#
> +# (C) Copyright 2011 Freescale Semiconductor, Inc.
> +# Jason Liu <r64343@freescale.com>
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y += mx53ppd.o vpd_reader.o
> +obj-$(CONFIG_VIDEO) += mx53ppd_video.o
> diff --git a/board/freescale/mx53ppd/imximage.cfg b/board/freescale/mx53ppd/imximage.cfg
> new file mode 100644
> index 0000000..83ff4b8
> --- /dev/null
> +++ b/board/freescale/mx53ppd/imximage.cfg
> @@ -0,0 +1,87 @@
> +/*
> + * Copyright 2017 General Electric Company
> + *
> + * Based on board/freescale/mx53loco/imximage.cfg:
> + *
> + * Copyright (C) 2011 Freescale Semiconductor, Inc.
> + * Jason Liu <r64343@freescale.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + *
> + * Refer doc/README.imximage for more details about how-to configure
> + * and create imximage boot image
> + *
> + * The syntax is taken as close as possible with the kwbimage
> + */
> +
> +/* image version */
> +IMAGE_VERSION 2
> +
> +/*
> + * Boot Device : one of
> + * spi, sd (the board has no nand neither onenand)
> + */
> +BOOT_FROM sd
> +
> +/*
> + * Device Configuration Data (DCD)
> + *
> + * Each entry must have the format:
> + * Addr-type Address Value
> + *
> + * where:
> + * Addr-type register length (1,2 or 4 bytes)
> + * Address absolute address of the register
> + * value value to be stored in the register
> + */
> +DATA 4 0x53fa8004 0x00194005
> +DATA 4 0x53fa8554 0x00300000
> +DATA 4 0x53fa8558 0x00300040
> +DATA 4 0x53fa8560 0x00300000
> +DATA 4 0x53fa8564 0x00300040
> +DATA 4 0x53fa8568 0x00300040
> +DATA 4 0x53fa8570 0x00300000
> +DATA 4 0x53fa8574 0x00300000
> +DATA 4 0x53fa8578 0x00300000
> +DATA 4 0x53fa857c 0x00300040
> +DATA 4 0x53fa8580 0x00300040
> +DATA 4 0x53fa8584 0x00300000
> +DATA 4 0x53fa8588 0x00300000
> +DATA 4 0x53fa8590 0x00300040
> +DATA 4 0x53fa8594 0x00300000
> +DATA 4 0x53fa86f0 0x00300000
> +DATA 4 0x53fa86f4 0x00000000
> +DATA 4 0x53fa86fc 0x00000000
> +DATA 4 0x53fa8714 0x00000000
> +DATA 4 0x53fa8718 0x00300000
> +DATA 4 0x53fa871c 0x00300000
> +DATA 4 0x53fa8720 0x00300000
> +DATA 4 0x53fa8728 0x00300000
> +DATA 4 0x53fa872c 0x00300000
> +DATA 4 0x63fd9088 0x35343535
> +DATA 4 0x63fd9090 0x4d444c44
> +DATA 4 0x63fd907c 0x01370138
> +DATA 4 0x63fd9080 0x013b013c
> +DATA 4 0x63fd9018 0x00111740
> +DATA 4 0x63fd9000 0x85190000
> +DATA 4 0x63fd900c 0x8b8f52e3
> +DATA 4 0x63fd9010 0xb68e8a63
> +DATA 4 0x63fd9014 0x01ff00db
> +DATA 4 0x63fd902c 0x000026d2
> +DATA 4 0x63fd9030 0x008f0e21
> +DATA 4 0x63fd9008 0x09333030
> +DATA 4 0x63fd9004 0x0002002d
> +DATA 4 0x63fd901c 0x00008032
> +DATA 4 0x63fd901c 0x00008033
> +DATA 4 0x63fd901c 0x00468031
> +DATA 4 0x63fd901c 0x052080b0
> +DATA 4 0x63fd901c 0x04008040
> +DATA 4 0x63fd901c 0x0000803a
> +DATA 4 0x63fd901c 0x0000803b
> +DATA 4 0x63fd901c 0x00028039
> +DATA 4 0x63fd901c 0x05208138
> +DATA 4 0x63fd901c 0x04008048
> +DATA 4 0x63fd9020 0x00005800
> +DATA 4 0x63fd9040 0x05380003
> +DATA 4 0x63fd9058 0x00011110
> +DATA 4 0x63fd901c 0x00000000
> diff --git a/board/freescale/mx53ppd/mx53ppd.c b/board/freescale/mx53ppd/mx53ppd.c
> new file mode 100644
> index 0000000..8c26f27
> --- /dev/null
> +++ b/board/freescale/mx53ppd/mx53ppd.c
> @@ -0,0 +1,487 @@
> +/*
> + * Copyright 2017 General Electric Company
> + *
> + * Based on board/freescale/mx53loco/mx53loco.c:
> + *
> + * Copyright (C) 2011 Freescale Semiconductor, Inc.
> + * Jason Liu <r64343@freescale.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/arch/crm_regs.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/iomux-mx53.h>
> +#include <asm/arch/clock.h>
> +#include <linux/errno.h>
> +#include <asm/mach-imx/mxc_i2c.h>
> +#include <asm/mach-imx/mx5_video.h>
> +#include <netdev.h>
> +#include <i2c.h>
> +#include <mmc.h>
> +#include <fsl_esdhc.h>
> +#include <asm/gpio.h>
> +#include <power/pmic.h>
> +#include <dialog_pmic.h>
> +#include <fsl_pmic.h>
> +#include <linux/fb.h>
> +#include <ipu_pixfmt.h>
> +#include <watchdog.h>
> +#include "ppd_gpio.h"
> +#include <stdlib.h>
> +#include "vpd_reader.h"
> +#include <rtc.h>
> +
> +#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +/* Index of I2C1, SEGMENT 1 (see CONFIG_SYS_I2C_BUSES). */
> +#define VPD_EEPROM_BUS 2
> +
> +/* Address of 24C08 EEPROM. */
> +#define VPD_EEPROM_ADDR 0x50
> +#define VPD_EEPROM_ADDR_LEN 1
> +
> +static uint32_t mx53_dram_size[2];
> +
> +phys_size_t get_effective_memsize(void)
> +{
> + /*
> + * WARNING: We must override get_effective_memsize() function here
> + * to report only the size of the first DRAM bank. This is to make
> + * U-Boot relocator place U-Boot into valid memory, that is, at the
> + * end of the first DRAM bank. If we did not override this function
> + * like so, U-Boot would be placed at the address of the first DRAM
> + * bank + total DRAM size - sizeof(uboot), which in the setup where
> + * each DRAM bank contains 512MiB of DRAM would result in placing
> + * U-Boot into invalid memory area close to the end of the first
> + * DRAM bank.
> + */
> + return mx53_dram_size[0];
> +}
> +
> +int dram_init(void)
> +{
> + mx53_dram_size[0] = get_ram_size((void *)PHYS_SDRAM_1, 1 << 30);
> + mx53_dram_size[1] = get_ram_size((void *)PHYS_SDRAM_2, 1 << 30);
> +
> + gd->ram_size = mx53_dram_size[0] + mx53_dram_size[1];
> +
> + return 0;
> +}
> +
> +int dram_init_banksize(void)
> +{
> + gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
> + gd->bd->bi_dram[0].size = mx53_dram_size[0];
> +
> + gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
> + gd->bd->bi_dram[1].size = mx53_dram_size[1];
> +
> + return 0;
> +}
> +
> +u32 get_board_rev(void)
> +{
> + struct iim_regs *iim = (struct iim_regs *)IMX_IIM_BASE;
> + struct fuse_bank *bank = &iim->bank[0];
> + struct fuse_bank0_regs *fuse =
> + (struct fuse_bank0_regs *)bank->fuse_regs;
> +
> + int rev = readl(&fuse->gp[6]);
> +
> + rev = 0;
> +
> + return (get_cpu_rev() & ~(0xF << 8)) | (rev & 0xF) << 8;
> +}
> +
> +#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
> + PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
> +
> +#ifdef CONFIG_USB_EHCI_MX5
> +int board_ehci_hcd_init(int port)
> +{
> + /* request VBUS power enable pin, GPIO7_8 */
> + imx_iomux_v3_setup_pad(MX53_PAD_PATA_DA_2__GPIO7_8);
> + gpio_direction_output(IMX_GPIO_NR(7, 8), 1);
> + return 0;
> +}
> +#endif
> +
> +static void setup_iomux_fec(void)
> +{
> + static const iomux_v3_cfg_t fec_pads[] = {
> + NEW_PAD_CTRL(MX53_PAD_FEC_MDIO__FEC_MDIO, PAD_CTL_HYS |
> + PAD_CTL_DSE_HIGH | PAD_CTL_PUS_22K_UP | PAD_CTL_ODE),
> + NEW_PAD_CTRL(MX53_PAD_FEC_MDC__FEC_MDC, PAD_CTL_DSE_HIGH),
> + NEW_PAD_CTRL(MX53_PAD_FEC_RXD1__FEC_RDATA_1,
> + PAD_CTL_HYS | PAD_CTL_PKE),
> + NEW_PAD_CTRL(MX53_PAD_FEC_RXD0__FEC_RDATA_0,
> + PAD_CTL_HYS | PAD_CTL_PKE),
> + NEW_PAD_CTRL(MX53_PAD_FEC_TXD1__FEC_TDATA_1, PAD_CTL_DSE_HIGH),
> + NEW_PAD_CTRL(MX53_PAD_FEC_TXD0__FEC_TDATA_0, PAD_CTL_DSE_HIGH),
> + NEW_PAD_CTRL(MX53_PAD_FEC_TX_EN__FEC_TX_EN, PAD_CTL_DSE_HIGH),
> + NEW_PAD_CTRL(MX53_PAD_FEC_REF_CLK__FEC_TX_CLK,
> + PAD_CTL_HYS | PAD_CTL_PKE),
> + NEW_PAD_CTRL(MX53_PAD_FEC_RX_ER__FEC_RX_ER,
> + PAD_CTL_HYS | PAD_CTL_PKE),
> + NEW_PAD_CTRL(MX53_PAD_FEC_CRS_DV__FEC_RX_DV,
> + PAD_CTL_HYS | PAD_CTL_PKE),
> + };
> +
> + imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
> +}
> +
> +#ifdef CONFIG_FSL_ESDHC
> +struct fsl_esdhc_cfg esdhc_cfg[2] = {
> + {MMC_SDHC3_BASE_ADDR},
> + {MMC_SDHC1_BASE_ADDR},
> +};
> +
> +int board_mmc_getcd(struct mmc *mmc)
> +{
> + return 1;
> +}
> +
> +#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
> + PAD_CTL_PUS_100K_UP)
> +#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
> + PAD_CTL_DSE_HIGH)
> +
> +int board_mmc_init(bd_t *bis)
> +{
> + static const iomux_v3_cfg_t sd1_pads[] = {
> + NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
> + SD_CMD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
> + MX53_PAD_EIM_DA11__GPIO3_11,
> + };
> +
> + static const iomux_v3_cfg_t sd2_pads[] = {
> + NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
> + MX53_PAD_EIM_DA13__GPIO3_13,
> + };
> +
> + u32 index;
> + int ret;
> +
> + esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
> + esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
> +
> + for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
> + switch (index) {
> + case 0:
> + imx_iomux_v3_setup_multiple_pads(sd1_pads,
> + ARRAY_SIZE(sd1_pads));
> + break;
> + case 1:
> + imx_iomux_v3_setup_multiple_pads(sd2_pads,
> + ARRAY_SIZE(sd2_pads));
> + break;
> + default:
> + printf("Warning: you configured more ESDHC controller"
> + "(%d) as supported by the board(2)\n",
> + CONFIG_SYS_FSL_ESDHC_NUM);
> + return -EINVAL;
> + }
> + ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
> +}
> +#endif
> +
> +#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
> + PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
> +
> +static void setup_iomux_i2c(void)
> +{
> + static const iomux_v3_cfg_t i2c1_pads[] = {
> + NEW_PAD_CTRL(MX53_PAD_CSI0_DAT8__I2C1_SDA, I2C_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_CSI0_DAT9__I2C1_SCL, I2C_PAD_CTRL),
> + };
> +
> + imx_iomux_v3_setup_multiple_pads(i2c1_pads, ARRAY_SIZE(i2c1_pads));
> +}
> +
> +#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
> +
> +static struct i2c_pads_info i2c_pad_info1 = {
> + .scl = {
> + .i2c_mode = MX53_PAD_EIM_D21__I2C1_SCL | I2C_PAD,
> + .gpio_mode = MX53_PAD_EIM_D28__GPIO3_28 | I2C_PAD,
> + .gp = IMX_GPIO_NR(3, 28)
> + },
> + .sda = {
> + .i2c_mode = MX53_PAD_EIM_D28__I2C1_SDA | I2C_PAD,
> + .gpio_mode = MX53_PAD_EIM_D21__GPIO3_21 | I2C_PAD,
> + .gp = IMX_GPIO_NR(3, 21)
> + }
> +};
> +
> +static void clock_1GHz(void)
> +{
> + int ret;
> + u32 ref_clk = MXC_HCLK;
> + /*
> + * After increasing voltage to 1.25V, we can switch
> + * CPU clock to 1GHz and DDR to 400MHz safely
> + */
> + ret = mxc_set_clock(ref_clk, 1000, MXC_ARM_CLK);
> + if (ret)
> + printf("CPU: Switch CPU clock to 1GHZ failed\n");
> +
> + ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
> + ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
> + if (ret)
> + printf("CPU: Switch DDR clock to 400MHz failed\n");
> +}
> +
> +void ppd_gpio_init(void)
> +{
> + int i;
> + imx_iomux_v3_setup_multiple_pads(ppd_pads, ARRAY_SIZE(ppd_pads));
> + for (i = 0; i < ARRAY_SIZE(ppd_gpios); ++i) {
> + gpio_direction_output(ppd_gpios[i].gpio, ppd_gpios[i].value);
> + }
> +}
> +
> +int board_early_init_f(void)
> +{
> + setup_iomux_fec();
> + setup_iomux_lcd();
> + ppd_gpio_init();
> +
> + return 0;
> +}
> +
> +/*
> + * Do not overwrite the console
> + * Use always serial for U-Boot console
> + */
> +int overwrite_console(void)
> +{
> + return 1;
> +}
> +
> +#define VPD_TYPE_INVALID 0x00
> +#define VPD_BLOCK_NETWORK 0x20
> +#define VPD_BLOCK_HWID 0x44
> +#define VPD_PRODUCT_PPD 4
> +#define VPD_HAS_MAC1 0x1
> +#define VPD_MAC_ADDRESS_LENGTH 6
> +
> +struct vpd_cache {
> + uint8_t product_id;
> + uint8_t has;
> + unsigned char mac1[VPD_MAC_ADDRESS_LENGTH];
> +};
> +
> +/*
> + * Extracts MAC and product information from the VPD.
> + */
> +static int vpd_callback(
> + void *userdata,
> + uint8_t id,
> + uint8_t version,
> + uint8_t type,
> + size_t size,
> + uint8_t const *data)
> +{
> + struct vpd_cache *vpd = (struct vpd_cache *)userdata;
> +
> + if ( id == VPD_BLOCK_HWID
> + && version == 1
> + && type != VPD_TYPE_INVALID
> + && size >= 1) {
> + vpd->product_id = data[0];
> +
> + } else if ( id == VPD_BLOCK_NETWORK
> + && version == 1
> + && type != VPD_TYPE_INVALID) {
> + if (size >= 6) {
> + vpd->has |= VPD_HAS_MAC1;
> + memcpy(vpd->mac1, data, VPD_MAC_ADDRESS_LENGTH);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static void process_vpd(struct vpd_cache *vpd)
> +{
> + int fec_index = -1;
> +
> + switch (vpd->product_id)
> + {
> + case VPD_PRODUCT_PPD:
> + fec_index = 0;
> + break;
> + }
> +
> + if (fec_index >= 0 && (vpd->has & VPD_HAS_MAC1)) {
> + eth_env_set_enetaddr("ethaddr", vpd->mac1);
> + }
> +}
> +
> +static int read_vpd(uint eeprom_bus)
> +{
> + struct vpd_cache vpd;
> + int res;
> + int size = 1024;
> + uint8_t *data;
> + unsigned int current_i2c_bus = i2c_get_bus_num();
> +
> + res = i2c_set_bus_num(eeprom_bus);
> + if (res < 0)
> + return res;
> +
> + data = (uint8_t *)malloc(size);
> + if (!data)
> + return -ENOMEM;
> +
> + res = i2c_read(VPD_EEPROM_ADDR, 0,
> + VPD_EEPROM_ADDR_LEN, data, size);
> +
> + if (res == 0) {
> + memset(&vpd, 0, sizeof(vpd));
> + vpd_reader(size, data, &vpd, vpd_callback);
> + process_vpd(&vpd);
> + }
> +
> + free(data);
> +
> + i2c_set_bus_num(current_i2c_bus);
> + return res;
> +}
> +
> +void check_time(void)
> +{
> + int ret, i;
> + struct rtc_time tm;
> + u8 retry = 3;
> +
> + unsigned int current_i2c_bus = i2c_get_bus_num();
> +
> + ret = i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM);
> + if (ret < 0)
> + return;
> +
> + rtc_init();
> +
> + for (i = 0; i < retry; i++) {
> + ret = rtc_get(&tm);
> + if(!ret || ret == -EINVAL) {
> + break;
> + }
> + }
> +
> + if (ret < 0) {
> + env_set("rtc_status", "RTC_ERROR");
> + }
> +
> + if (tm.tm_year > 2037) {
> + tm.tm_sec = 0;
> + tm.tm_min = 0;
> + tm.tm_hour = 0;
> + tm.tm_mday = 1;
> + tm.tm_wday = 2;
> + tm.tm_mon = 1;
> + tm.tm_year = 2036;
Agree this will be a problem in 2037, but I guess setting the time back
is not the right solution. I am missing the reason, apart to convince
kernel that time does not go by.
> +
> + for (i = 0; i < retry; i++) {
> + ret = rtc_set(&tm);
> + if(!ret) {
> + break;
> + }
> + }
> +
> + if (ret < 0)
> + env_set("rtc_status", "RTC_ERROR");
> + }
> +
> + i2c_set_bus_num(current_i2c_bus);
> +}
> +
> +int board_init(void)
> +{
> + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
> +
> + mxc_set_sata_internal_clock();
> + setup_iomux_i2c();
> +
> + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
> +
> + return 0;
> +}
> +
> +int misc_init_r(void)
> +{
> + const char *cause;
> +
> + /* We care about WDOG only, treating everything else as
> + * a power-on-reset.
> + */
> + if (get_imx_reset_cause() & 0x0010) {
> + cause = "WDOG";
> + } else {
> + cause = "POR";
> + }
> +
> + env_set("bootcause", cause);
> +
> + return 0;
> +}
> +
> +int board_late_init(void)
> +{
> + read_vpd(VPD_EEPROM_BUS);
> +
> + clock_1GHz();
> + print_cpuinfo();
> + hw_watchdog_init();
> +
> + check_time();
> +
> + return 0;
> +}
> +
> +int checkboard(void)
> +{
> + puts("Board: GE PPD\n");
> +
> + return 0;
> +}
> +
> +static int do_lcd_enable(cmd_tbl_t *cmdtp, int flag, int argc,
> + char * const argv[])
> +{
> + lcd_enable();
> + return 0;
> +}
> +
If this is related to LCD, why the function is not in mx53ppd_video.c ?
> +U_BOOT_CMD(
> + ppd_lcd_enable, 1, 1, do_lcd_enable,
> + "enable PPD LCD",
> + "no parameters"
> +);
> diff --git a/board/freescale/mx53ppd/mx53ppd_video.c b/board/freescale/mx53ppd/mx53ppd_video.c
> new file mode 100644
> index 0000000..338f00f
> --- /dev/null
> +++ b/board/freescale/mx53ppd/mx53ppd_video.c
> @@ -0,0 +1,123 @@
> +/*
> + * Copyright 2017 General Electric Company
> + *
> + * Based on board/freescale/mx53loco/mx53loco_video.c:
> + *
> + * Copyright (C) 2012 Freescale Semiconductor, Inc.
> + * Fabio Estevam <fabio.estevam@freescale.com>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <linux/list.h>
> +#include <asm/gpio.h>
> +#include <asm/arch/iomux-mx53.h>
> +#include <linux/fb.h>
> +#include <ipu_pixfmt.h>
> +#include <asm/arch/crm_regs.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/io.h>
> +#include <pwm.h>
> +#include "ppd_gpio.h"
> +
> +#define MX53PPD_LCD_POWER IMX_GPIO_NR(3, 24)
> +
> +static struct fb_videomode const nv_spwg = {
> + .name = "NV-SPWGRGB888",
> + .refresh = 60,
> + .xres = 800,
> + .yres = 480,
> + .pixclock = 15384,
> + .left_margin = 16,
> + .right_margin = 210,
> + .upper_margin = 10,
> + .lower_margin = 22,
> + .hsync_len = 30,
> + .vsync_len = 13,
> + .sync = FB_SYNC_EXT,
> + .vmode = FB_VMODE_NONINTERLACED
> +};
> +
> +
> +void setup_iomux_lcd(void)
> +{
> + static const iomux_v3_cfg_t lcd_pads[] = {
> + MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK,
> + MX53_PAD_DI0_PIN15__IPU_DI0_PIN15,
> + MX53_PAD_DI0_PIN2__IPU_DI0_PIN2,
> + MX53_PAD_DI0_PIN3__IPU_DI0_PIN3,
> + MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0,
> + MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1,
> + MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2,
> + MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3,
> + MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4,
> + MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5,
> + MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6,
> + MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7,
> + MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8,
> + MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9,
> + MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10,
> + MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11,
> + MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12,
> + MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13,
> + MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14,
> + MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15,
> + MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16,
> + MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17,
> + MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18,
> + MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19,
> + MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20,
> + MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21,
> + MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22,
> + MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23,
> + };
> +
> + imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
> +}
> +
> +void lcd_enable(void)
> +{
> + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
> + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
> +
> + /* Set LDB_DI0 as clock source for IPU_DI0 */
> + clrsetbits_le32(&mxc_ccm->cscmr2,
> + MXC_CCM_CSCMR2_DI0_CLK_SEL_MASK,
> + MXC_CCM_CSCMR2_DI0_CLK_SEL(MXC_CCM_CSCMR2_DI0_CLK_SEL_LDB_DI0_CLK));
> +
> + /* Turn on IPU LDB DI0 clocks */
> + setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_LDB_DI0(3));
> +
> + /* Turn on IPU DI0 clocks */
> + setbits_le32(&mxc_ccm->CCGR6, MXC_CCM_CCGR6_IPU_DI0(3));
> +
> + /* Configure LDB */
> + writel(IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
> + IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
> + IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
> + &iomux->gpr[2]);
> +
> + /* Enable backlights */
> + pwm_init(1, 0, 0);
> +
> + /* duty cycle 5000000ns, period: 5000000ns */
> + pwm_config(1, 5000000, 5000000);
> +
> + /* Backlight Power */
> + gpio_direction_output(BACKLIGHT_ENABLE, 1);
> +
> + pwm_enable(1);
> +}
> +
> +
> +int board_video_skip(void)
> +{
> + int ret;
> +
> + ret = ipuv3_fb_init(&nv_spwg, 0, IPU_PIX_FMT_RGB24);
> + if (ret)
> + printf("Display cannot be configured: %d\n", ret);
> +
> + return ret;
> +}
> diff --git a/board/freescale/mx53ppd/ppd_gpio.h b/board/freescale/mx53ppd/ppd_gpio.h
> new file mode 100644
> index 0000000..a722435
> --- /dev/null
> +++ b/board/freescale/mx53ppd/ppd_gpio.h
> @@ -0,0 +1,96 @@
> +/*
> + * (C) Copyright 2015 General Electric Company
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __PPD_GPIO_H_
> +#define __PPD_GPIO_H_
> +
> +#include <asm/arch/iomux-mx53.h>
> +#include <asm/gpio.h>
> +
> +#define PPD_UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
> + PAD_CTL_PUS_100K_UP)
> +
> +static const iomux_v3_cfg_t ppd_pads[] = {
> + /* FEC */
> + MX53_PAD_EIM_A22__GPIO2_16,
> + /* UART */
> + NEW_PAD_CTRL(MX53_PAD_PATA_DMACK__UART1_RXD_MUX, PPD_UART_PAD_CTRL),
> + NEW_PAD_CTRL(MX53_PAD_PATA_DIOW__UART1_TXD_MUX, PPD_UART_PAD_CTRL),
> + /* Video */
> + MX53_PAD_CSI0_DATA_EN__GPIO5_20, /* LR_SCAN_CTRL */
> + MX53_PAD_CSI0_VSYNC__GPIO5_21, /* UD_SCAN_CTRL */
> + MX53_PAD_CSI0_DAT10__GPIO5_28, /* DATA_WIDTH_CTRL */
> + MX53_PAD_CSI0_PIXCLK__GPIO5_18, /* HOST_CONTROLLED_RESET_TO_LCD_N */
> + MX53_PAD_EIM_DA2__GPIO3_2, /* LVDS1_MUX_CTRL */
> + MX53_PAD_EIM_DA3__GPIO3_3, /* LVDS0_MUX_CTRL */
> + MX53_PAD_EIM_A21__GPIO2_17, /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
> + MX53_PAD_CSI0_DAT11__GPIO5_29, /* BACKLIGHT_ENABLE */
> + MX53_PAD_DISP0_DAT9__PWM2_PWMO, /* IMX535_PWM2_TO_LCD_CONNECTOR */
> + /* I2C */
> + MX53_PAD_EIM_A20__GPIO2_18, /* RESET_I2C1_BUS_SEGMENT_MUX_N */
> +
> + /* SPI */
> + MX53_PAD_DISP0_DAT23__GPIO5_17,
> + MX53_PAD_KEY_COL2__GPIO4_10,
> + MX53_PAD_KEY_ROW2__GPIO4_11,
> + MX53_PAD_KEY_COL3__GPIO4_12,
> +};
> +
> +struct gpio_cfg {
> + unsigned gpio;
> + int value;
> +};
> +
> +#define RESET_IMX535_ETHERNET_PHY_N IMX_GPIO_NR(2, 16)
> +#define UD_SCAN_CTRL IMX_GPIO_NR(5, 21)
> +#define LR_SCAN_CTRL IMX_GPIO_NR(5, 20)
> +#define LVDS0_MUX_CTRL IMX_GPIO_NR(3, 3)
> +#define LVDS1_MUX_CTRL IMX_GPIO_NR(3, 2)
> +#define HOST_CONTROLLED_RESET_TO_LCD_N IMX_GPIO_NR(5, 18)
> +#define DATA_WIDTH_CTRL IMX_GPIO_NR(5, 28)
> +#define RESET_DP0_TRANSMITTER_N IMX_GPIO_NR(2, 28)
> +#define RESET_DP1_TRANSMITTER_N IMX_GPIO_NR(2, 29)
> +#define POWER_DOWN_LVDS0_DESERIALIZER_N IMX_GPIO_NR(2, 22)
> +#define POWER_DOWN_LVDS1_DESERIALIZER_N IMX_GPIO_NR(2, 27)
> +#define ENABLE_PWR_TO_LCD_AND_UI_INTERFACE IMX_GPIO_NR(2, 17)
> +#define BACKLIGHT_ENABLE IMX_GPIO_NR(5, 29)
> +#define RESET_I2C1_BUS_SEGMENT_MUX_N IMX_GPIO_NR(2, 18)
> +#define ECSPI1_CS0 IMX_GPIO_NR(5, 17)
> +#define ECSPI1_CS1 IMX_GPIO_NR(4, 10)
> +#define ECSPI1_CS2 IMX_GPIO_NR(4, 11)
> +#define ECSPI1_CS3 IMX_GPIO_NR(4, 12)
> +
> +static const struct gpio_cfg ppd_gpios[] = {
> + /* FEC */
> + /* Drive Low as GPIO output for 25ms per Eth Phy IX spec */
> + /* Then Drive High as GPIO output to bring Eth Phy IC out of reset */
> + { RESET_IMX535_ETHERNET_PHY_N, 0 },
> + { RESET_IMX535_ETHERNET_PHY_N, 1 },
> + /* Video */
> + { UD_SCAN_CTRL, 0 },
> + { LR_SCAN_CTRL, 1 },
> +#ifdef PROPRIETARY_CHANGES
> + { LVDS0_MUX_CTRL, 1 },
> +#else
> + { LVDS0_MUX_CTRL, 0 },
> +#endif
> + { LVDS1_MUX_CTRL, 1 },
> + { HOST_CONTROLLED_RESET_TO_LCD_N, 1 },
> + { DATA_WIDTH_CTRL, 0 },
> + { RESET_DP0_TRANSMITTER_N, 1 },
> + { RESET_DP1_TRANSMITTER_N, 1 },
> + { POWER_DOWN_LVDS0_DESERIALIZER_N, 1 },
> + { POWER_DOWN_LVDS1_DESERIALIZER_N, 1 },
> + { ENABLE_PWR_TO_LCD_AND_UI_INTERFACE, 1 },
> + { BACKLIGHT_ENABLE, 0 },
> + { RESET_I2C1_BUS_SEGMENT_MUX_N, 1 },
> + { ECSPI1_CS0, 1 },
> + { ECSPI1_CS1, 1 },
> + { ECSPI1_CS2, 1 },
> + { ECSPI1_CS3, 1 },
> +};
> +
> +#endif /* __PPD_GPIO_H_ */
> diff --git a/board/freescale/mx53ppd/vpd_reader.c b/board/freescale/mx53ppd/vpd_reader.c
> new file mode 100644
> index 0000000..ea6daf7
> --- /dev/null
> +++ b/board/freescale/mx53ppd/vpd_reader.c
> @@ -0,0 +1,230 @@
> +/*
> + * Copyright 2016 General Electric Company
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include "vpd_reader.h"
> +
> +#include <linux/bch.h>
> +#include <stdlib.h>
> +#include <errno.h>
> +
> +
> +/* BCH configuration */
> +
> +const struct {
> + int header_ecc_capability_bits;
> + int data_ecc_capability_bits;
> + unsigned int prim_poly;
> + struct {
> + int min;
> + int max;
> + } galois_field_order;
> +} bch_configuration = {
> + .header_ecc_capability_bits = 4,
> + .data_ecc_capability_bits = 16,
> + .prim_poly = 0,
> + .galois_field_order = {
> + .min = 5,
> + .max = 15,
> + },
> +};
> +
> +static int calculate_galois_field_order(size_t source_length)
> +{
> + int gfo = bch_configuration.galois_field_order.min;
> +
> + for (; gfo < bch_configuration.galois_field_order.max &&
> + ((((1 << gfo) - 1) - ((int)source_length * 8)) < 0);
> + gfo++) {
> + }
> +
> + if (gfo == bch_configuration.galois_field_order.max) {
> + return -1;
> + }
> +
> + return gfo + 1;
> +}
> +
mmmhhh....I do not like this. You have already a handling for VPD header
(your custom header) for the bx50v3 board. You duplicate here a lot of
code, and I am missing what is different and what is identical.
I think you should move code in a common directory (as freescale boards
do), like in ge/common, and the same code is reused by all your board
instead of duplicating it each time.
> +static int verify_bch(int ecc_bits, unsigned int prim_poly,
> + uint8_t * data, size_t data_length,
> + const uint8_t * ecc, size_t ecc_length)
> +{
> + int gfo = calculate_galois_field_order(data_length);
> + if (gfo < 0) {
> + return -1;
> + }
> +
> + struct bch_control * bch = init_bch(gfo, ecc_bits, prim_poly);
> + if (!bch) {
> + return -1;
> + }
> +
> + if (bch->ecc_bytes != ecc_length) {
> + free_bch(bch);
> + return -1;
> + }
> +
> + unsigned * errloc = (unsigned *)calloc(data_length, sizeof(unsigned));
> + int errors = decode_bch(
> + bch, data, data_length, ecc, NULL, NULL, errloc);
> + free_bch(bch);
> + if (errors < 0) {
> + free(errloc);
> + return -1;
> + }
> +
> + if (errors > 0) {
> + int n;
> + for (n = 0; n < errors; n++) {
> + if (errloc[n] >= 8 * data_length) {
> + /* n-th error located in ecc (no need for data correction) */
> + } else {
> + /* n-th error located in data */
> + data[errloc[n] / 8] ^= 1 << (errloc[n] % 8);
> + }
> + }
> + }
> +
> + free(errloc);
> + return 0;
> +}
> +
> +
> +static const int ID = 0;
> +static const int LEN = 1;
> +static const int VER = 2;
> +static const int TYP = 3;
> +static const int BLOCK_SIZE = 4;
> +
> +static const uint8_t HEADER_BLOCK_ID = 0x00;
> +static const uint8_t HEADER_BLOCK_LEN = 18;
> +static const uint32_t HEADER_BLOCK_MAGIC = 0xca53ca53;
> +static const size_t HEADER_BLOCK_VERIFY_LEN = 14;
> +static const size_t HEADER_BLOCK_ECC_OFF = 14;
> +static const size_t HEADER_BLOCK_ECC_LEN = 4;
> +
> +static const uint8_t ECC_BLOCK_ID = 0xFF;
> +
> +int vpd_reader(
> + size_t size,
> + uint8_t * data,
> + void * userdata,
> + int (*fn)(
> + void * userdata,
> + uint8_t id,
> + uint8_t version,
> + uint8_t type,
> + size_t size,
> + uint8_t const * data))
> +{
> + if ( size < HEADER_BLOCK_LEN
> + || data == NULL
> + || fn == NULL) {
> + return -EINVAL;
> + }
> +
> + /*
> + * +--------------------+--------------------+--//--+--------------------+
> + * | header block | data block | ... | ecc block |
> + * +--------------------+--------------------+--//--+--------------------+
> + * : : :
> + * +------+-------+-----+ +------+-------------+
> + * | id | magic | ecc | | ... | ecc |
> + * | len | off | | +------+-------------+
> + * | ver | size | | :
> + * | type | | | :
> + * +------+-------+-----+ :
> + * : : : :
> + * <----- [1] ----> <----------- [2] ----------->
> + *
> + * Repair (if necessary) the contents of header block [1] by using a
> + * 4 byte ECC located at the end of the header block. A successful
> + * return value means that we can trust the header.
> + */
> + int ret = verify_bch(
> + bch_configuration.header_ecc_capability_bits,
> + bch_configuration.prim_poly,
> + data,
> + HEADER_BLOCK_VERIFY_LEN,
> + &data[HEADER_BLOCK_ECC_OFF],
> + HEADER_BLOCK_ECC_LEN);
> + if (ret < 0) {
> + return ret;
> + }
> +
> + /* Validate header block { id, length, version, type }. */
> + if ( data[ID] != HEADER_BLOCK_ID
> + || data[LEN] != HEADER_BLOCK_LEN
> + || data[VER] != 0
> + || data[TYP] != 0
> + || ntohl(*(uint32_t *)(&data[4])) != HEADER_BLOCK_MAGIC) {
> + return -EINVAL;
> + }
> +
> + uint32_t offset = ntohl(*(uint32_t *)(&data[8]));
> + uint16_t size_bits = ntohs(*(uint16_t *)(&data[12]));
> +
> + /* Check that ECC header fits. */
> + if (offset + 3 >= size) {
> + return -EINVAL;
> + }
> +
> + /* Validate ECC block. */
> + uint8_t * ecc = &data[offset];
> + if ( ecc[ID] != ECC_BLOCK_ID
> + || ecc[LEN] < BLOCK_SIZE
> + || ecc[LEN] + offset > size
> + || ecc[LEN] - BLOCK_SIZE != size_bits / 8
> + || ecc[VER] != 1
> + || ecc[TYP] != 1) {
> + return -EINVAL;
> + }
> +
> + /*
> + * Use the header block to locate the ECC block and verify the data
> + * blocks [2] against the ecc block ECC.
> + */
> + ret = verify_bch(
> + bch_configuration.data_ecc_capability_bits,
> + bch_configuration.prim_poly,
> + &data[data[LEN]],
> + offset - data[LEN],
> + &data[offset + BLOCK_SIZE],
> + ecc[LEN] - BLOCK_SIZE);
> + if (ret < 0) {
> + return ret;
> + }
> +
> + /* Stop after ECC. Ignore possible zero padding. */
> + size = offset;
> +
> + for (;;) {
> + /* Move to next block. */
> + size -= data[LEN];
> + data += data[LEN];
> +
> + if (size == 0) {
> + /* Finished iterating through blocks. */
> + return 0;
> + }
> +
> + if ( size < BLOCK_SIZE
> + || data[LEN] < BLOCK_SIZE) {
> + /* Not enough data for a header, or short header. */
> + return -EINVAL;
> + }
> +
> + ret = fn(
> + userdata,
> + data[ID],
> + data[VER],
> + data[TYP],
> + data[LEN] - BLOCK_SIZE,
> + &data[BLOCK_SIZE]);
> + if (ret) {
> + return ret;
> + }
> + }
> +}
> diff --git a/board/freescale/mx53ppd/vpd_reader.h b/board/freescale/mx53ppd/vpd_reader.h
> new file mode 100644
> index 0000000..efa172a
> --- /dev/null
> +++ b/board/freescale/mx53ppd/vpd_reader.h
> @@ -0,0 +1,25 @@
> +/*
> + * Copyright 2016 General Electric Company
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include "common.h"
> +
> +/*
> + * Read VPD from given data, verify content, and call callback
> + * for each vital product data block.
> + *
> + * Returns Non-zero on error. Negative numbers encode errno.
> + */
> +int vpd_reader(
> + size_t size,
> + uint8_t * data,
> + void * userdata,
> + int (*fn)(
> + void * userdata,
> + uint8_t id,
> + uint8_t version,
> + uint8_t type,
> + size_t size,
> + uint8_t const * data));
> diff --git a/configs/mx53ppd_defconfig b/configs/mx53ppd_defconfig
> new file mode 100644
> index 0000000..1cc3578
> --- /dev/null
> +++ b/configs/mx53ppd_defconfig
> @@ -0,0 +1,39 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_MX5=y
> +CONFIG_TARGET_MX53PPD=y
> +CONFIG_FIT=y
> +CONFIG_BOOTCOUNT=y
> +CONFIG_BOOTCOUNT_EXT=y
> +CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE="mmc"
> +CONFIG_SYS_BOOTCOUNT_EXT_DEVPART="0:5"
> +CONFIG_SYS_BOOTCOUNT_EXT_NAME="/boot/failures"
> +CONFIG_SYS_BOOTCOUNT_ADDR=0x7000A000
> +CONFIG_NETDEVICES=y
> +CONFIG_VIDEO=y
> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53ppd/imximage.cfg"
> +CONFIG_BOOTDELAY=1
> +# CONFIG_CONSOLE_MUX is not set
> +CONFIG_SYS_CONSOLE_IS_IN_ENV=y
> +CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
> +CONFIG_DISPLAY_CPUINFO=y
> +CONFIG_HUSH_PARSER=y
> +CONFIG_CMD_BOOTZ=y
> +CONFIG_CMD_I2C=y
> +CONFIG_RTC_S35392A=y
> +# CONFIG_CMD_IMLS is not set
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_DHCP=y
> +CONFIG_CMD_MII=y
> +CONFIG_CMD_PING=y
> +CONFIG_CMD_EXT2=y
> +CONFIG_CMD_EXT4=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_CMD_FAT=y
> +CONFIG_CMD_FS_GENERIC=y
> +CONFIG_USB=y
> +CONFIG_USB_STORAGE=y
> +# CONFIG_VIDEO_SW_CURSOR is not set
> +CONFIG_OF_LIBFDT=y
> +
> +CONFIG_MMC=y
> diff --git a/include/configs/mx53ppd.h b/include/configs/mx53ppd.h
> new file mode 100644
> index 0000000..59cc527
> --- /dev/null
> +++ b/include/configs/mx53ppd.h
> @@ -0,0 +1,246 @@
> +/*
> + * Copyright (C) 2011 Freescale Semiconductor, Inc.
> + * Jason Liu <r64343@freescale.com>
> + *
> + * Configuration settings for Freescale MX53 low cost board.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#define CONFIG_MACH_TYPE MACH_TYPE_MX53_PPD
> +
> +#include <asm/arch/imx-regs.h>
> +
> +#define CONSOLE_DEV "ttymxc0"
> +
> +#define CONFIG_CMDLINE_TAG
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_INITRD_TAG
> +
> +#define CONFIG_SYS_FSL_CLK
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
> +
> +#define CONFIG_HW_WATCHDOG
> +#define CONFIG_IMX_WATCHDOG
> +#define CONFIG_WATCHDOG_TIMEOUT_MSECS 8000
> +
> +#define CONFIG_MISC_INIT_R
> +#define CONFIG_BOARD_LATE_INIT
> +#define CONFIG_MXC_GPIO
> +#define CONFIG_REVISION_TAG
> +
> +#define CONFIG_MXC_UART
> +#define CONFIG_MXC_UART_BASE UART1_BASE
> +
> +/* MMC Configs */
> +#define CONFIG_FSL_ESDHC
> +#define CONFIG_SYS_FSL_ESDHC_ADDR 0
> +#define CONFIG_SYS_FSL_ESDHC_NUM 2
> +
> +#define CONFIG_SUPPORT_RAW_INITRD /* bootz raw initrd support */
> +
> +/* Eth Configs */
> +#define CONFIG_MII
> +
> +#define CONFIG_FEC_MXC
> +#define IMX_FEC_BASE FEC_BASE_ADDR
> +#define CONFIG_FEC_MXC_PHYADDR 0x1F
> +
> +/* USB Configs */
> +#define CONFIG_USB_EHCI_MX5
> +#define CONFIG_USB_HOST_ETHER
> +#define CONFIG_USB_ETHER_ASIX
> +#define CONFIG_USB_ETHER_MCS7830
> +#define CONFIG_USB_ETHER_SMSC95XX
> +#define CONFIG_MXC_USB_PORT 1
> +#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
> +#define CONFIG_MXC_USB_FLAGS 0
> +
> +#define CONFIG_SYS_RTC_BUS_NUM 2
> +#define CONFIG_SYS_I2C_RTC_ADDR 0x30
> +
> +/* I2C Configs */
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MXC
> +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
> +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
> +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
> +
> +/* PMIC Controller */
> +#define CONFIG_POWER
> +#define CONFIG_POWER_I2C
> +#define CONFIG_DIALOG_POWER
> +#define CONFIG_POWER_FSL
> +#define CONFIG_POWER_FSL_MC13892
> +#define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
> +#define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8
> +
> +/* allow to overwrite serial and ethaddr */
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_CONS_INDEX 1
> +#define CONFIG_BAUDRATE 115200
> +
> +/* Command definition */
> +#define CONFIG_SUPPORT_RAW_INITRD
> +
> +
> +#define CONFIG_ETHPRIME "FEC0"
> +
> +#define CONFIG_LOADADDR 0x72000000 /* loadaddr env var */
> +#define CONFIG_SYS_TEXT_BASE 0x77800000
> +
> +#define PPD_CONFIG_NFS \
> + "nfsserver=192.168.252.95\0" \
> + "gatewayip=192.168.252.95\0" \
> + "netmask=255.255.255.0\0" \
> + "ipaddr=192.168.252.99\0" \
> + "kernsize=0x2000\0" \
> + "use_dhcp=0\0" \
> + "nfsroot=/opt/springdale/rd\0" \
> + "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs ${kern_ipconf} nfsroot=${nfsserver}:${nfsroot},v3,tcp rw\0" \
> + "choose_ip=if test $use_dhcp = 1; then set kern_ipconf ip=dhcp; set getcmd dhcp; else set kern_ipconf ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off; set getcmd tftp; fi\0" \
> + "nfs=run choose_ip setargs bootargs_nfs; ${getcmd} ${loadaddr} ${nfsserver}:${image}; bootm ${loadaddr}\0" \
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + PPD_CONFIG_NFS \
> + "bootlimit=10\0" \
> + "image=/boot/fitImage\0" \
> + "fdt_high=0xffffffff\0" \
> + "dev=mmc\0" \
> + "devnum=0\0" \
> + "rootdev=mmcblk0p\0" \
> + "quiet=quiet loglevel=0\0" \
> + "console=" CONSOLE_DEV "\0" \
> + "lvds=ldb\0" \
> + "setargs=setenv bootargs ${lvds} jtag=on mem=2G vt.global_cursor_default=0 " \
> + "bootcause=${bootcause} " \
> + "${quiet} console=${console} ${rtc_status}" \
> + "\0" \
> + "bootargs_emmc=setenv bootargs root=/dev/${rootdev}${partnum} " \
> + "ro rootwait ${bootargs}\0" \
> + "doquiet=" \
> + "if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; then setenv quiet; fi\0" \
> + "hasfirstboot=" \
> + "ext2load ${dev} ${devnum}:${partnum} 0x7000A000 /boot/bootcause/firstboot\0" \
> + "swappartitions=" \
> + "setexpr partnum 3 - ${partnum}\0" \
> + "failbootcmd=" \
> + "ppd_lcd_enable; " \
> + "msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
> + "echo $msg; " \
> + "setenv stdout vga; " \
> + "echo \"\n\n\n\n \" $msg; " \
> + "setenv stdout serial; " \
> + "mw.b 0x7000A000 0xbc; " \
> + "mw.b 0x7000A001 0x00; " \
> + "ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
> + "altbootcmd=" \
> + "run doquiet; " \
> + "setenv partnum 1; run hasfirstboot || setenv partnum 2; run hasfirstboot || setenv partnum 0; " \
> + "if test ${partnum} != 0; then " \
> + "setenv bootcause REVERT; " \
> + "run swappartitions loadimage doboot; " \
> + "fi; " \
> + "run failbootcmd\0" \
> + "loadimage=" \
> + "ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
> + "doboot=" \
> + "echo Booting from ${dev}:${devnum}:${partnum} ...; " \
> + "run setargs; " \
> + "run bootargs_emmc; " \
> + "bootm ${loadaddr}\0" \
> + "tryboot=" \
> + "setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
> + "run loadimage || run swappartitions && run loadimage || setenv partnum 0 && echo MISSING IMAGE;" \
> + "run doboot; " \
> + "run failbootcmd\0" \
> + "video-mode=" \
> + "lcd:800x480-24 at 60,monitor=lcd\0" \
> +
> +
> +#define CONFIG_MMCBOOTCOMMAND \
> + "if mmc dev ${devnum}; then " \
> + "run doquiet; " \
> + "run tryboot; " \
> + "fi; " \
> +
> +#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
> +
> +#define CONFIG_ARP_TIMEOUT 200UL
> +
> +/* Miscellaneous configurable options */
> +#define CONFIG_SYS_LONGHELP /* undef to save memory */
> +#define CONFIG_AUTO_COMPLETE
> +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
> +
> +#define CONFIG_SYS_MAXARGS 48 /* max number of command args */
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
> +
> +#define CONFIG_SYS_MEMTEST_START 0x70000000
> +#define CONFIG_SYS_MEMTEST_END 0x70010000
> +
> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> +
> +#define CONFIG_CMDLINE_EDITING
> +
> +/* Physical Memory Map */
> +#define CONFIG_NR_DRAM_BANKS 2
> +#define PHYS_SDRAM_1 CSD0_BASE_ADDR
> +#define PHYS_SDRAM_1_SIZE (gd->bd->bi_dram[0].size)
> +#define PHYS_SDRAM_2 CSD1_BASE_ADDR
> +#define PHYS_SDRAM_2_SIZE (gd->bd->bi_dram[1].size)
> +#define PHYS_SDRAM_SIZE (gd->ram_size)
> +
> +#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
> +#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
> +#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)
> +
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +/* FLASH and environment organization */
> +#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
> +#define CONFIG_ENV_SIZE (8 * 1024)
> +#define CONFIG_ENV_IS_IN_MMC
> +#define CONFIG_SYS_MMC_ENV_DEV 0
> +
> +#define CONFIG_CMD_FUSE
> +#define CONFIG_FSL_IIM
> +
> +#define CONFIG_SYS_I2C_SPEED 100000
> +
> +/* I2C1 */
> +#define CONFIG_SYS_NUM_I2C_BUSES 9
> +#define CONFIG_SYS_I2C_MAX_HOPS 1
> +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
> + {0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
> + }
> +
> +#define CONFIG_BCH
> +
> +#define CONFIG_BOOTCOUNT_LIMIT
> +
> +/* Backlight Control */
> +#define CONFIG_PWM_IMX
> +#define CONFIG_IMX6_PWM_PER_CLK 66666000
> +
> +/* Framebuffer and LCD */
> +#ifdef CONFIG_VIDEO
> + #define CONFIG_VIDEO_IPUV3
> +#endif
> +
> +#endif /* __CONFIG_H */
>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53
2017-11-01 15:42 ` Martyn Welch
@ 2017-11-01 15:58 ` Stefano Babic
0 siblings, 0 replies; 17+ messages in thread
From: Stefano Babic @ 2017-11-01 15:58 UTC (permalink / raw)
To: u-boot
Hi Martyn,
On 01/11/2017 16:42, Martyn Welch wrote:
> On Wed, 2017-11-01 at 16:31 +0100, Stefano Babic wrote:
>> On 01/11/2017 15:23, Martyn Welch wrote:
>>> Add missing parts for i.MX53 PWM support
>>>
>>> Acked-by: Nandor Han <nandor.han@ge.com>
>>> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
>>> Cc: Stefano Babic <sbabic@denx.de>
>>> ---
>>> arch/arm/include/asm/arch-mx5/imx-regs.h | 19 +++++++++++++++++++
>>> drivers/pwm/pwm-imx-util.c | 2 ++
>>> 2 files changed, 21 insertions(+)
>>>
>>> diff --git a/arch/arm/include/asm/arch-mx5/imx-regs.h b/arch/arm/include/asm/arch-mx5/imx-regs.h
>>> index 3e79fa3..c2ff798 100644
>>> --- a/arch/arm/include/asm/arch-mx5/imx-regs.h
>>> +++ b/arch/arm/include/asm/arch-mx5/imx-regs.h
>>> @@ -508,6 +508,25 @@ struct fuse_bank4_regs {
>>> };
>>> #endif
>>>
>>> +#if defined(CONFIG_MX53)
>>
>> It looks to me this is not MX53 specific. You are already changing a MX5
>> file. As far as I see, this is valid at least for MX51. Do we need the
>> #ifdef ?
>>
>
> I only have access to an MX53, I'm not familiar with the rest of the MX5
> family and was thus playing it safe.
Yes, but the reference manual for MX51 and MX53 (Chapter 38 in MX51)
shows the same register layout.
Best regards,
Stefano
>
>>> +#define PWMCR_PRESCALER(x) (((x - 1) & 0xFFF) << 4)
>>> +#define PWMCR_DOZEEN (1 << 24)
>>> +#define PWMCR_WAITEN (1 << 23)
>>> +#define PWMCR_DBGEN (1 << 22)
>>> +#define PWMCR_CLKSRC_IPG_HIGH (2 << 16)
>>> +#define PWMCR_CLKSRC_IPG (1 << 16)
>>> +#define PWMCR_EN (1 << 0)
>>> +
>>> +struct pwm_regs {
>>> + u32 cr;
>>> + u32 sr;
>>> + u32 ir;
>>> + u32 sar;
>>> + u32 pr;
>>> + u32 cnr;
>>> +};
>>> +#endif
>>> +
>>> #endif /* __ASSEMBLER__*/
>>>
>>> #endif /* __ASM_ARCH_MX5_IMX_REGS_H__ */
>>> diff --git a/drivers/pwm/pwm-imx-util.c b/drivers/pwm/pwm-imx-util.c
>>> index 534dd8e..97ac0c8 100644
>>> --- a/drivers/pwm/pwm-imx-util.c
>>> +++ b/drivers/pwm/pwm-imx-util.c
>>> @@ -23,10 +23,12 @@ struct pwm_regs *pwm_id_to_reg(int pwm_id)
>>> return (struct pwm_regs *)PWM1_BASE_ADDR;
>>> case 1:
>>> return (struct pwm_regs *)PWM2_BASE_ADDR;
>>> +#ifdef CONFIG_MX6
>>> case 2:
>>> return (struct pwm_regs *)PWM3_BASE_ADDR;
>>> case 3:
>>> return (struct pwm_regs *)PWM4_BASE_ADDR;
>>> +#endif
>>> #ifdef CONFIG_MX6SX
>>> case 4:
>>> return (struct pwm_regs *)PWM5_BASE_ADDR;
>>>
>>
>>
>> Best regards,
>> Stefano Babic
>>
>
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem
2017-11-01 15:28 ` Stefano Babic
@ 2017-11-01 16:24 ` Tom Rini
0 siblings, 0 replies; 17+ messages in thread
From: Tom Rini @ 2017-11-01 16:24 UTC (permalink / raw)
To: u-boot
On Wed, Nov 01, 2017 at 04:28:14PM +0100, Stefano Babic wrote:
> Hi Martin, Ian,
>
> On 01/11/2017 15:23, Martyn Welch wrote:
> > From: Ian Ray <ian.ray@ge.com>
> >
> > Add support for bootcounter on an EXT filesystem.
> > Sync configuration whitelist.
> >
> > Signed-off-by: Ian Ray <ian.ray@ge.com>
> > Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> > ---
> > Changes for v2:
> > - Adding Kconfig for EXT bootcount.
> >
> > Changes for v3:
> > - Add over-arching BOOTCOUNT Kconfig entry.
> >
>
> Should we better split this into two ? The patch patch does more as
> commit message suggests. First, it moves bootcounter to Kconfig (first
> topic). Second, it adds EXT support.
It's only adding EXT bootcount to Kconfig. It's the first one an today
bootcount doesn't have a global symbol.
--
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20171101/dc68c3ad/attachment.sig>
^ permalink raw reply [flat|nested] 17+ messages in thread
* [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD
2017-11-01 15:53 ` Stefano Babic
@ 2017-11-01 17:56 ` Martyn Welch
0 siblings, 0 replies; 17+ messages in thread
From: Martyn Welch @ 2017-11-01 17:56 UTC (permalink / raw)
To: u-boot
On Wed, 2017-11-01 at 16:53 +0100, Stefano Babic wrote:
> Hi Martyn, Peter,
>
> On 01/11/2017 15:23, Martyn Welch wrote:
> > From: Peter Senna Tschudin <peter.senna@collabora.com>
> >
> > Create board support for GE PPD, based on mx53loco.
> >
> > Use mx53ppd_defconfig make target to configure for this board.
> >
> > Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
> > Signed-off-by: Ian Ray <ian.ray@ge.com>
> > Signed-off-by: Nandor Han <nandor.han@ge.com>
> > Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
> > Cc: Stefano Babic <sbabic@denx.de>
> > ---
> > Changes for v2:
> > - Replacing boot count related defines with default config.
> >
> > Changes for v3:
> > - Update config due to BOOTCOUNT Kconfig addition.
> >
> > arch/arm/include/asm/mach-types.h | 1 +
> > arch/arm/mach-imx/mx5/Kconfig | 5 +
> > board/freescale/mx53ppd/Kconfig | 17 ++
> > board/freescale/mx53ppd/MAINTAINERS | 7 +
> > board/freescale/mx53ppd/Makefile | 12 +
> > board/freescale/mx53ppd/imximage.cfg | 87 ++++++
> > board/freescale/mx53ppd/mx53ppd.c | 487 ++++++++++++++++++++++++++++++++
> > board/freescale/mx53ppd/mx53ppd_video.c | 123 ++++++++
> > board/freescale/mx53ppd/ppd_gpio.h | 96 +++++++
> > board/freescale/mx53ppd/vpd_reader.c | 230 +++++++++++++++
> > board/freescale/mx53ppd/vpd_reader.h | 25 ++
> > configs/mx53ppd_defconfig | 39 +++
> > include/configs/mx53ppd.h | 246 ++++++++++++++++
> > 13 files changed, 1375 insertions(+)
> > create mode 100644 board/freescale/mx53ppd/Kconfig
> > create mode 100644 board/freescale/mx53ppd/MAINTAINERS
> > create mode 100644 board/freescale/mx53ppd/Makefile
> > create mode 100644 board/freescale/mx53ppd/imximage.cfg
> > create mode 100644 board/freescale/mx53ppd/mx53ppd.c
> > create mode 100644 board/freescale/mx53ppd/mx53ppd_video.c
> > create mode 100644 board/freescale/mx53ppd/ppd_gpio.h
> > create mode 100644 board/freescale/mx53ppd/vpd_reader.c
> > create mode 100644 board/freescale/mx53ppd/vpd_reader.h
> > create mode 100644 configs/mx53ppd_defconfig
> > create mode 100644 include/configs/mx53ppd.h
> >
> > diff --git a/arch/arm/include/asm/mach-types.h b/arch/arm/include/asm/mach-types.h
> > index 9f82efe..2a257cc 100644
> > --- a/arch/arm/include/asm/mach-types.h
> > +++ b/arch/arm/include/asm/mach-types.h
> > @@ -5057,4 +5057,5 @@
> > #define MACH_TYPE_NASM25 5112
> > #define MACH_TYPE_TOMATO 5113
> > #define MACH_TYPE_OMAP3_MRC3D 5114
> > +#define MACH_TYPE_MX53_PPD 5134
>
> Ouch..still an ancient Kernel ? 2.6.35, maybe ?
>
No, currently 4.11.
> Even in that case, we agreed to not touch anymore mach-types.h. The
> value should go into the board configuration file,
>
> #define CONFIG_MACH_TYPE 5134
>
I hadn't realised I could drop it. Now dropped entirely
<snip>
> > +void check_time(void)
> > +{
> > + int ret, i;
> > + struct rtc_time tm;
> > + u8 retry = 3;
> > +
> > + unsigned int current_i2c_bus = i2c_get_bus_num();
> > +
> > + ret = i2c_set_bus_num(CONFIG_SYS_RTC_BUS_NUM);
> > + if (ret < 0)
> > + return;
> > +
> > + rtc_init();
> > +
> > + for (i = 0; i < retry; i++) {
> > + ret = rtc_get(&tm);
> > + if(!ret || ret == -EINVAL) {
> > + break;
> > + }
> > + }
> > +
> > + if (ret < 0) {
> > + env_set("rtc_status", "RTC_ERROR");
> > + }
> > +
> > + if (tm.tm_year > 2037) {
> > + tm.tm_sec = 0;
> > + tm.tm_min = 0;
> > + tm.tm_hour = 0;
> > + tm.tm_mday = 1;
> > + tm.tm_wday = 2;
> > + tm.tm_mon = 1;
> > + tm.tm_year = 2036;
>
> Agree this will be a problem in 2037, but I guess setting the time back
> is not the right solution. I am missing the reason, apart to convince
> kernel that time does not go by.
>
The device has mitigation in user-space to warn the user should it be
running when the time approaches this date (either because it's actually
2037 or if the device has been accidentally configured to think it is
2037). We believe there exists a risk that the device will fail to boot
correctly if we try booting after the epoch has overflowed.
To us it is preferable that a device boots with the wrong date, but in
an otherwise usable state, rather than doesn't boot. This is a medical
device, so it could actually be a matter of life and death...
<snip>
> > +
> > +static int do_lcd_enable(cmd_tbl_t *cmdtp, int flag, int argc,
> > + char * const argv[])
> > +{
> > + lcd_enable();
> > + return 0;
> > +}
> > +
>
> If this is related to LCD, why the function is not in mx53ppd_video.c ?
>
I'll move it.
> > +U_BOOT_CMD(
> > + ppd_lcd_enable, 1, 1, do_lcd_enable,
> > + "enable PPD LCD",
> > + "no parameters"
> > +);
<snip>
> > diff --git a/board/freescale/mx53ppd/vpd_reader.c b/board/freescale/mx53ppd/vpd_reader.c
> > new file mode 100644
> > index 0000000..ea6daf7
> > --- /dev/null
> > +++ b/board/freescale/mx53ppd/vpd_reader.c
> > @@ -0,0 +1,230 @@
> > +/*
> > + * Copyright 2016 General Electric Company
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#include "vpd_reader.h"
> > +
> > +#include <linux/bch.h>
> > +#include <stdlib.h>
> > +#include <errno.h>
> > +
> > +
> > +/* BCH configuration */
> > +
> > +const struct {
> > + int header_ecc_capability_bits;
> > + int data_ecc_capability_bits;
> > + unsigned int prim_poly;
> > + struct {
> > + int min;
> > + int max;
> > + } galois_field_order;
> > +} bch_configuration = {
> > + .header_ecc_capability_bits = 4,
> > + .data_ecc_capability_bits = 16,
> > + .prim_poly = 0,
> > + .galois_field_order = {
> > + .min = 5,
> > + .max = 15,
> > + },
> > +};
> > +
> > +static int calculate_galois_field_order(size_t source_length)
> > +{
> > + int gfo = bch_configuration.galois_field_order.min;
> > +
> > + for (; gfo < bch_configuration.galois_field_order.max &&
> > + ((((1 << gfo) - 1) - ((int)source_length * 8)) < 0);
> > + gfo++) {
> > + }
> > +
> > + if (gfo == bch_configuration.galois_field_order.max) {
> > + return -1;
> > + }
> > +
> > + return gfo + 1;
> > +}
> > +
>
> mmmhhh....I do not like this. You have already a handling for VPD header
> (your custom header) for the bx50v3 board. You duplicate here a lot of
> code, and I am missing what is different and what is identical.
>
> I think you should move code in a common directory (as freescale boards
> do), like in ge/common, and the same code is reused by all your board
> instead of duplicating it each time.
>
Yup, sorry, I'd not thought about it also being in the bx50v3 support.
I'll make this common.
Martyn
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2017-11-01 17:56 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-11-01 14:23 [U-Boot] [PATCH v3 0/7] Add support for GE PPD Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 1/7] imx: mxc_i2c: tweak the i2c transfer method Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 2/7] ext4: recover from filesystem corruption when reading Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 3/7] pwm: imx: Enable PWM support on i.MX53 Martyn Welch
2017-11-01 15:31 ` Stefano Babic
2017-11-01 15:42 ` Martyn Welch
2017-11-01 15:58 ` Stefano Babic
2017-11-01 14:23 ` [U-Boot] [PATCH v3 4/7] arm: mx5: Add more register definitions Martyn Welch
2017-11-01 15:33 ` Stefano Babic
2017-11-01 14:23 ` [U-Boot] [PATCH v3 5/7] bootcount: add support for bootcounter on EXT filesystem Martyn Welch
2017-11-01 14:41 ` Tom Rini
2017-11-01 15:28 ` Stefano Babic
2017-11-01 16:24 ` Tom Rini
2017-11-01 14:23 ` [U-Boot] [PATCH v3 6/7] rtc: add support for s35392a Martyn Welch
2017-11-01 14:23 ` [U-Boot] [PATCH v3 7/7] mx53: Add Board support for GE PPD Martyn Welch
2017-11-01 15:53 ` Stefano Babic
2017-11-01 17:56 ` Martyn Welch
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.