From: Tim Harvey <tharvey@gateworks.com>
To: linux-media@vger.kernel.org, alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
shawnguo@kernel.org, Steve Longerbeam <slongerbeam@gmail.com>,
Philipp Zabel <p.zabel@pengutronix.de>,
Hans Verkuil <hansverk@cisco.com>,
Mauro Carvalho Chehab <mchehab@s-opensource.com>
Subject: [PATCH 4/5] ARM: dts: imx: Add TDA19971 HDMI Receiver to GW54xx
Date: Thu, 9 Nov 2017 10:45:35 -0800 [thread overview]
Message-ID: <1510253136-14153-5-git-send-email-tharvey@gateworks.com> (raw)
In-Reply-To: <1510253136-14153-1-git-send-email-tharvey@gateworks.com>
The GW54xx has a front-panel microHDMI connector routed to a TDA19971
which is connected the the IPU CSI when using IMX6Q.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
---
v2:
- add HDMI audio input support
---
arch/arm/boot/dts/imx6q-gw54xx.dts | 102 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 29 +++++++++-
2 files changed, 128 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/imx6q-gw54xx.dts b/arch/arm/boot/dts/imx6q-gw54xx.dts
index 56e5b50..99dac63 100644
--- a/arch/arm/boot/dts/imx6q-gw54xx.dts
+++ b/arch/arm/boot/dts/imx6q-gw54xx.dts
@@ -12,10 +12,27 @@
/dts-v1/;
#include "imx6q.dtsi"
#include "imx6qdl-gw54xx.dtsi"
+#include <dt-bindings/media/tda1997x.h>
/ {
model = "Gateworks Ventana i.MX6 Dual/Quad GW54XX";
compatible = "gw,imx6q-gw54xx", "gw,ventana", "fsl,imx6q";
+
+ sound-digital {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "tda1997x-audio";
+ simple-audio-card,dai-link@0 {
+ format = "i2s";
+ cpu {
+ sound-dai = <&ssi2>;
+ };
+ codec {
+ bitclock-master;
+ frame-master;
+ sound-dai = <&tda1997x>;
+ };
+ };
+ };
};
&i2c3 {
@@ -35,6 +52,61 @@
};
};
};
+
+ tda1997x: codec@48 {
+ compatible = "nxp,tda19971";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tda1997x>;
+ reg = <0x48>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ DOVDD-supply = <®_3p3v>;
+ AVDD-supply = <&sw4_reg>;
+ DVDD-supply = <&sw4_reg>;
+ #sound-dai-cells = <0>;
+ nxp,audout-format = "i2s";
+ nxp,audout-layout = <0>;
+ nxp,audout-width = <16>;
+ nxp,audout-mclk-fs = <128>;
+ /*
+ * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+ * and Y[11:4] across 16bits in the same cycle
+ * which we map to VP[15:08]<->CSI_DATA[19:12]
+ */
+ nxp,vidout-portcfg =
+ /*G_Y_11_8<->VP[15:12]<->CSI_DATA[19:16]*/
+ < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+ /*G_Y_7_4<->VP[11:08]<->CSI_DATA[15:12]*/
+ < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+ /*R_CR_CBCR_11_8<->VP[07:04]<->CSI_DATA[11:08]*/
+ < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+ /*R_CR_CBCR_7_4<->VP[03:00]<->CSI_DATA[07:04]*/
+ < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+ port {
+ tda1997x_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <16>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ data-active = <1>;
+ };
+ };
+ };
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <16>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&tda1997x_to_ipu1_csi0_mux>;
+ bus-width = <16>;
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
};
&ipu2_csi1_from_ipu2_csi1_mux {
@@ -63,6 +135,30 @@
>;
};
+ pinctrl_ipu1_csi0: ipu1_csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
+ >;
+ };
+
pinctrl_ipu2_csi1: ipu2_csi1grp {
fsl,pins = <
MX6QDL_PAD_EIM_EB2__IPU2_CSI1_DATA19 0x1b0b0
@@ -78,4 +174,10 @@
MX6QDL_PAD_EIM_A16__IPU2_CSI1_PIXCLK 0x1b0b0
>;
};
+
+ pinctrl_tda1997x: tda1997xgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
+ >;
+ };
};
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index 07458a2..1bcb298 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -10,6 +10,7 @@
*/
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
/ {
/* these are used by bootloader for disabling nodes */
@@ -114,12 +115,12 @@
};
};
- sound {
+ sound-analog {
compatible = "fsl,imx6q-ventana-sgtl5000",
"fsl,imx-audio-sgtl5000";
model = "sgtl5000-audio";
ssi-controller = <&ssi1>;
- audio-codec = <&codec>;
+ audio-codec = <&sgtl5000>;
audio-routing =
"MIC_IN", "Mic Jack",
"Mic Jack", "Mic Bias",
@@ -133,6 +134,25 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>; /* AUD4<->sgtl5000 */
status = "okay";
+
+ ssi2 {
+ fsl,audmux-port = <1>;
+ fsl,port-config = <
+ (IMX_AUDMUX_V2_PTCR_TFSDIR |
+ IMX_AUDMUX_V2_PTCR_TFSEL(4+8) | /* RXFS */
+ IMX_AUDMUX_V2_PTCR_TCLKDIR |
+ IMX_AUDMUX_V2_PTCR_TCSEL(4+8) | /* RXC */
+ IMX_AUDMUX_V2_PTCR_SYN)
+ IMX_AUDMUX_V2_PDCR_RXDSEL(4)
+ >;
+ };
+
+ aud5 {
+ fsl,audmux-port = <4>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN
+ IMX_AUDMUX_V2_PDCR_RXDSEL(1)>;
+ };
};
&can1 {
@@ -331,7 +351,7 @@
pinctrl-0 = <&pinctrl_i2c3>;
status = "okay";
- codec: sgtl5000@0a {
+ sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
reg = <0x0a>;
clocks = <&clks IMX6QDL_CLK_CKO>;
@@ -475,6 +495,9 @@
MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0
MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0
MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 /* AUD4_MCK */
+ MX6QDL_PAD_EIM_D25__AUD5_RXC 0x130b0
+ MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+ MX6QDL_PAD_EIM_D24__AUD5_RXFS 0x130b0
>;
};
--
2.7.4
next prev parent reply other threads:[~2017-11-09 18:46 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-11-09 18:45 [PATCH v3 0/5] TDA1997x HDMI video receiver Tim Harvey
2017-11-09 18:45 ` Tim Harvey
2017-11-09 18:45 ` [PATCH 1/5] MAINTAINERS: add entry for NXP TDA1997x driver Tim Harvey
2017-11-09 18:45 ` [PATCH 2/5] media: dt-bindings: Add bindings for TDA1997X Tim Harvey
2017-11-09 18:45 ` Tim Harvey
2017-11-22 7:36 ` Sakari Ailus
2017-11-22 7:36 ` Sakari Ailus
2017-11-23 4:37 ` Tim Harvey
2017-11-23 8:25 ` Sakari Ailus
2017-11-23 8:25 ` Sakari Ailus
2017-11-29 15:54 ` Tim Harvey
2017-11-29 15:54 ` Tim Harvey
2017-11-09 18:45 ` [PATCH 3/5] media: i2c: Add TDA1997x HDMI receiver driver Tim Harvey
2017-11-15 15:52 ` Rob Herring
2017-11-15 15:52 ` Rob Herring
2017-11-15 18:31 ` Tim Harvey
2017-11-15 18:31 ` Tim Harvey
2017-11-16 4:30 ` Rob Herring
2017-11-16 4:30 ` Rob Herring
2017-11-23 4:49 ` Tim Harvey
2017-11-23 4:49 ` Tim Harvey
2017-12-12 12:18 ` Hans Verkuil
2017-12-13 23:33 ` Tim Harvey
2017-12-13 23:33 ` Tim Harvey
2017-12-14 10:11 ` Hans Verkuil
2017-12-14 10:11 ` Hans Verkuil
2017-11-20 15:39 ` Hans Verkuil
2017-11-23 4:27 ` Tim Harvey
2017-11-23 4:27 ` Tim Harvey
2017-11-23 8:08 ` Hans Verkuil
2017-11-23 8:08 ` Hans Verkuil
2017-11-29 15:47 ` Tim Harvey
2017-12-16 19:32 ` [alsa-devel] " Fabio Estevam
2017-12-16 19:32 ` Fabio Estevam
2017-12-18 22:21 ` [alsa-devel] " Tim Harvey
2017-12-18 22:21 ` Tim Harvey
2017-11-09 18:45 ` Tim Harvey [this message]
2017-11-09 18:45 ` [PATCH 5/5] ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x Tim Harvey
2017-11-09 18:45 ` Tim Harvey
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1510253136-14153-5-git-send-email-tharvey@gateworks.com \
--to=tharvey@gateworks.com \
--cc=alsa-devel@alsa-project.org \
--cc=devicetree@vger.kernel.org \
--cc=hansverk@cisco.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@s-opensource.com \
--cc=p.zabel@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=slongerbeam@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.