All of lore.kernel.org
 help / color / mirror / Atom feed
From: <harinikatakamlinux@gmail.com>
To: <nicolas.ferre@atmel.com>, <davem@davemloft.net>,
	<harinikatakamlinux@gmail.com>
Cc: <netdev@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<harinik@xilinx.com>, <michals@xilinx.com>, <appanad@xilinx.com>
Subject: [RFC PATCH 4/5] net: macb: Add support for suspend/resume with full power down
Date: Thu, 22 Mar 2018 19:21:39 +0530	[thread overview]
Message-ID: <1521726700-22634-5-git-send-email-harinikatakamlinux@gmail.com> (raw)
In-Reply-To: <1521726700-22634-1-git-send-email-harinikatakamlinux@gmail.com>

From: Harini Katakam <harinik@xilinx.com>

When macb device is suspended and system is powered down, the clocks
are removed and hence macb should be closed gracefully and restored
upon resume. This patch does the same by switching off the net device,
suspending phy and performing necessary cleanup of interrupts and BDs.
Upon resume, all these are reinitialized again.

Reset of macb device is done only when GEM is not a wake device.
Even when gem is a wake device, tx queues can be stopped and ptp device
can be closed (tsu clock will be disabled in pm_runtime_suspend) as
wake event detection has no dependency on this.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
---
 drivers/net/ethernet/cadence/macb_main.c | 38 ++++++++++++++++++++++++++++++--
 1 file changed, 36 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index ce75088..bca91bd 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -4167,16 +4167,33 @@ static int __maybe_unused macb_suspend(struct device *dev)
 	struct platform_device *pdev = to_platform_device(dev);
 	struct net_device *netdev = platform_get_drvdata(pdev);
 	struct macb *bp = netdev_priv(netdev);
+	struct macb_queue *queue = bp->queues;
+	unsigned long flags;
+	unsigned int q;
+
+	if (!netif_running(netdev))
+		return 0;
 
-	netif_carrier_off(netdev);
-	netif_device_detach(netdev);
 
 	if (bp->wol & MACB_WOL_ENABLED) {
 		macb_writel(bp, IER, MACB_BIT(WOL));
 		macb_writel(bp, WOL, MACB_BIT(MAG));
 		enable_irq_wake(bp->queues[0].irq);
+		netif_device_detach(netdev);
+	} else {
+		netif_device_detach(netdev);
+		for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue)
+			napi_disable(&queue->napi);
+		phy_stop(netdev->phydev);
+		phy_suspend(netdev->phydev);
+		spin_lock_irqsave(&bp->lock, flags);
+		macb_reset_hw(bp);
+		spin_unlock_irqrestore(&bp->lock, flags);
 	}
 
+	netif_carrier_off(netdev);
+	if (bp->ptp_info)
+		bp->ptp_info->ptp_remove(netdev);
 	pm_runtime_force_suspend(dev);
 
 	return 0;
@@ -4187,6 +4204,11 @@ static int __maybe_unused macb_resume(struct device *dev)
 	struct platform_device *pdev = to_platform_device(dev);
 	struct net_device *netdev = platform_get_drvdata(pdev);
 	struct macb *bp = netdev_priv(netdev);
+	struct macb_queue *queue = bp->queues;
+	unsigned int q;
+
+	if (!netif_running(netdev))
+		return 0;
 
 	pm_runtime_force_resume(dev);
 
@@ -4194,9 +4216,21 @@ static int __maybe_unused macb_resume(struct device *dev)
 		macb_writel(bp, IDR, MACB_BIT(WOL));
 		macb_writel(bp, WOL, 0);
 		disable_irq_wake(bp->queues[0].irq);
+	} else {
+		macb_writel(bp, NCR, MACB_BIT(MPE));
+		for (q = 0, queue = bp->queues; q < bp->num_queues; ++q, ++queue)
+			napi_enable(&queue->napi);
+		netif_carrier_on(netdev);
+		phy_resume(netdev->phydev);
+		phy_start(netdev->phydev);
 	}
 
+	bp->macbgem_ops.mog_init_rings(bp);
+	macb_init_hw(bp);
+	macb_set_rx_mode(netdev);
 	netif_device_attach(netdev);
+	if (bp->ptp_info)
+		bp->ptp_info->ptp_init(netdev);
 
 	return 0;
 }
-- 
2.7.4

  parent reply	other threads:[~2018-03-22 13:52 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-03-22 13:51 [RFC PATCH 0/5] Macb power management support for ZynqMP harinikatakamlinux
2018-03-22 13:51 ` [RFC PATCH 1/5] net: macb: Check MDIO state before read/write and use timeouts harinikatakamlinux
2018-03-22 14:47   ` Andrew Lunn
2018-05-03 10:08   ` Claudiu Beznea
2018-05-03 10:58     ` Harini Katakam
2018-03-22 13:51 ` [RFC PATCH 2/5] net: macb: Support clock management for tsu_clk harinikatakamlinux
2018-03-22 13:51 ` [RFC PATCH 3/5] net: macb: Add pm runtime support harinikatakamlinux
2018-05-03 10:09   ` Claudiu Beznea
2018-05-03 11:13     ` Harini Katakam
2018-05-03 12:59       ` Claudiu Beznea
2018-03-22 13:51 ` harinikatakamlinux [this message]
2018-05-03 10:09   ` [RFC PATCH 4/5] net: macb: Add support for suspend/resume with full power down Claudiu Beznea
2018-05-03 11:20     ` Harini Katakam
2018-05-03 12:23       ` Claudiu Beznea
2018-03-22 13:51 ` [RFC PATCH 5/5] net: macb: Add WOL support with ARP harinikatakamlinux
2018-05-04 12:17   ` Claudiu Beznea
2018-05-10 10:37     ` Harini Katakam
2018-05-15  8:39       ` Claudiu Beznea

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1521726700-22634-5-git-send-email-harinikatakamlinux@gmail.com \
    --to=harinikatakamlinux@gmail.com \
    --cc=appanad@xilinx.com \
    --cc=davem@davemloft.net \
    --cc=harinik@xilinx.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=michals@xilinx.com \
    --cc=netdev@vger.kernel.org \
    --cc=nicolas.ferre@atmel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.