[U-Boot] [PATCH v3 6/8] powerpc: mpc85xx: Use binman to embed dtb inside U-Boot

[Jagdish Gediya <jagdish.gediya@nxp.com>]

Below is the sequence to embed dtb inside U-Boot,
1. Remove bootpg and resetvec section if needed
2. Append dtb
3. Append bootpg and resetvec section back if removed in step 1

Above procedure is required only when CONFIG_MPC85xx and
CONFIG_OF_SEPARATE are defined.

Add new config CONFIG_MPC85XX_HAVE_RESET_VECTOR to indicate that
image has resetvec section. Step 1 and step 3 described above are
required only if this config is y.

Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
---
Changes for v2:
	- Don't change the generic target
	- Add new config option to use binman

Changes for v3:
	- Commit message change('u-boot' -> 'U-Boot')

 Makefile                         | 23 ++++++++++++++++++++++-
 arch/powerpc/cpu/mpc85xx/Kconfig |  4 ++++
 2 files changed, 26 insertions(+), 1 deletion(-)

diff --git a/Makefile b/Makefile
index b5bf8ab..03baa74 100644
--- a/Makefile
+++ b/Makefile
@@ -861,6 +861,10 @@ ifneq ($(CONFIG_SYS_INIT_SP_BSS_OFFSET),)
 ALL-y += init_sp_bss_offset_check
 endif
 
+ifeq ($(CONFIG_MPC85xx)$(CONFIG_OF_SEPARATE),yy)
+ALL-y += u-boot-with-dtb.bin
+endif
+
 LDFLAGS_u-boot += $(LDFLAGS_FINAL)
 
 # Avoid 'Not enough room for program headers' error on binutils 2.28 onwards.
@@ -983,7 +987,8 @@ spl/u-boot-spl.srec: spl/u-boot-spl FORCE
 	$(call if_changed,objcopy)
 
 OBJCOPYFLAGS_u-boot-nodtb.bin := -O binary \
-		$(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec)
+		$(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec)	\
+		$(if $(CONFIG_MPC85XX_HAVE_RESET_VECTOR),-R .bootpg -R .resetvec)
 
 binary_size_check: u-boot-nodtb.bin FORCE
 	@file_size=$(shell wc -c u-boot-nodtb.bin | awk '{print $$1}') ; \
@@ -1202,6 +1207,18 @@ u-boot-with-spl.sfp: spl/u-boot-spl.sfp u-boot.img FORCE
 	$(call if_changed,socboot)
 endif
 
+ifeq ($(CONFIG_MPC85xx)$(CONFIG_OF_SEPARATE),yy)
+u-boot-with-dtb.bin: u-boot.bin u-boot.dtb \
+	$(if $(CONFIG_MPC85XX_HAVE_RESET_VECTOR), u-boot-br.bin) FORCE
+	$(call if_changed,binman)
+
+ifeq ($(CONFIG_MPC85XX_HAVE_RESET_VECTOR),y)
+OBJCOPYFLAGS_u-boot-br.bin := -O binary -j .bootpg -j .resetvec
+u-boot-br.bin: u-boot FORCE
+	$(call if_changed,objcopy)
+endif
+endif
+
 # x86 uses a large ROM. We fill it with 0xff, put the 16-bit stuff (including
 # reset vector) at the top, Intel ME descriptor at the bottom, and U-Boot in
 # the middle. This is handled by binman based on an image description in the
@@ -1296,8 +1313,12 @@ spl/u-boot-spl.pbl: spl/u-boot-spl.bin FORCE
 ifeq ($(ARCH),arm)
 UBOOT_BINLOAD := u-boot.img
 else
+ifeq ($(CONFIG_MPC85xx)$(CONFIG_OF_SEPARATE),yy)
+UBOOT_BINLOAD := u-boot-with-dtb.bin
+else
 UBOOT_BINLOAD := u-boot.bin
 endif
+endif
 
 OBJCOPYFLAGS_u-boot-with-spl-pbl.bin = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO) \
 			  --gap-fill=0xff
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 19e8d02..7d139ff 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -1143,6 +1143,10 @@ config ARCH_T4240
 	imply CMD_REGINFO
 	imply FSL_SATA
 
+config MPC85XX_HAVE_RESET_VECTOR
+	bool "Indicate reset vector at CONFIG_RESET_VECTOR_ADDRESS - 0xffc"
+	depends on MPC85xx
+
 config BOOKE
 	bool
 	default y
-- 
2.7.4