All of lore.kernel.org
 help / color / mirror / Atom feed
From: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com>
To: johan@kernel.org
Cc: gregkh@linuxfoundation.org, linux-usb@vger.kernel.org,
	linux-kernel@vger.kernel.org, peter_hong@fintek.com.tw,
	"Ji-Ze Hong (Peter Hong)" <hpeter+linux_kernel@gmail.com>
Subject: [PATCH V1 1/1] USB: serial: f81534: fix reading old/new IC config
Date: Thu, 15 Nov 2018 10:58:44 +0800	[thread overview]
Message-ID: <1542250724-11667-1-git-send-email-hpeter+linux_kernel@gmail.com> (raw)

The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
	+00h: to indicate the section is valid
	+01h~04h: UART Mode & port availability
	+05h~08h: Output pin control on IC power on
	+09h~12h: Output pin control on working <-- New added

Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.

This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81534.c | 20 +++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 380933db34dd..2b39bda035c7 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -45,14 +45,17 @@
 #define F81534_CONFIG1_REG		(0x09 + F81534_UART_BASE_ADDRESS)
 
 #define F81534_DEF_CONF_ADDRESS_START	0x3000
-#define F81534_DEF_CONF_SIZE		8
+#define F81534_DEF_CONF_SIZE		12
 
 #define F81534_CUSTOM_ADDRESS_START	0x2f00
 #define F81534_CUSTOM_DATA_SIZE		0x10
 #define F81534_CUSTOM_NO_CUSTOM_DATA	0xff
 #define F81534_CUSTOM_VALID_TOKEN	0xf0
 #define F81534_CONF_OFFSET		1
-#define F81534_CONF_GPIO_OFFSET		4
+#define F81534_CONF_INIT_GPIO_OFFSET	4
+#define F81534_CONF_WORK_GPIO_OFFSET	8
+#define F81534_CONF_GPIO_SHUTDOWN	7
+#define F81534_CONF_GPIO_RS232		1
 
 #define F81534_MAX_DATA_BLOCK		64
 #define F81534_MAX_BUS_RETRY		20
@@ -1337,8 +1340,19 @@ static int f81534_set_port_output_pin(struct usb_serial_port *port)
 	serial_priv = usb_get_serial_data(serial);
 	port_priv = usb_get_serial_port_data(port);
 
-	idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num;
+	idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num;
 	value = serial_priv->conf_data[idx];
+	if (value >= F81534_CONF_GPIO_SHUTDOWN) {
+		/*
+		 * Newer IC configure will make transceiver in shutdown mode on
+		 * initial power on. We need enable it before using UARTs.
+		 */
+		idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num;
+		value = serial_priv->conf_data[idx];
+		if (value >= F81534_CONF_GPIO_SHUTDOWN)
+			value = F81534_CONF_GPIO_RS232;
+	}
+
 	pins = &f81534_port_out_pins[port_priv->phy_num];
 
 	for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) {
-- 
2.7.4


WARNING: multiple messages have this Message-ID (diff)
From: "Ji-Ze Hong \(Peter Hong\)" <hpeter@gmail.com>
To: johan@kernel.org
Cc: gregkh@linuxfoundation.org, linux-usb@vger.kernel.org,
	linux-kernel@vger.kernel.org, peter_hong@fintek.com.tw,
	"Ji-Ze Hong \(Peter Hong\)" <hpeter+linux_kernel@gmail.com>
Subject: [V1,1/1] USB: serial: f81534: fix reading old/new IC config
Date: Thu, 15 Nov 2018 10:58:44 +0800	[thread overview]
Message-ID: <1542250724-11667-1-git-send-email-hpeter+linux_kernel@gmail.com> (raw)

The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
	+00h: to indicate the section is valid
	+01h~04h: UART Mode & port availability
	+05h~08h: Output pin control on IC power on
	+09h~12h: Output pin control on working <-- New added

Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.

This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
---
 drivers/usb/serial/f81534.c | 20 +++++++++++++++++---
 1 file changed, 17 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 380933db34dd..2b39bda035c7 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -45,14 +45,17 @@
 #define F81534_CONFIG1_REG		(0x09 + F81534_UART_BASE_ADDRESS)
 
 #define F81534_DEF_CONF_ADDRESS_START	0x3000
-#define F81534_DEF_CONF_SIZE		8
+#define F81534_DEF_CONF_SIZE		12
 
 #define F81534_CUSTOM_ADDRESS_START	0x2f00
 #define F81534_CUSTOM_DATA_SIZE		0x10
 #define F81534_CUSTOM_NO_CUSTOM_DATA	0xff
 #define F81534_CUSTOM_VALID_TOKEN	0xf0
 #define F81534_CONF_OFFSET		1
-#define F81534_CONF_GPIO_OFFSET		4
+#define F81534_CONF_INIT_GPIO_OFFSET	4
+#define F81534_CONF_WORK_GPIO_OFFSET	8
+#define F81534_CONF_GPIO_SHUTDOWN	7
+#define F81534_CONF_GPIO_RS232		1
 
 #define F81534_MAX_DATA_BLOCK		64
 #define F81534_MAX_BUS_RETRY		20
@@ -1337,8 +1340,19 @@ static int f81534_set_port_output_pin(struct usb_serial_port *port)
 	serial_priv = usb_get_serial_data(serial);
 	port_priv = usb_get_serial_port_data(port);
 
-	idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num;
+	idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num;
 	value = serial_priv->conf_data[idx];
+	if (value >= F81534_CONF_GPIO_SHUTDOWN) {
+		/*
+		 * Newer IC configure will make transceiver in shutdown mode on
+		 * initial power on. We need enable it before using UARTs.
+		 */
+		idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num;
+		value = serial_priv->conf_data[idx];
+		if (value >= F81534_CONF_GPIO_SHUTDOWN)
+			value = F81534_CONF_GPIO_RS232;
+	}
+
 	pins = &f81534_port_out_pins[port_priv->phy_num];
 
 	for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) {

             reply	other threads:[~2018-11-15  2:58 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-15  2:58 Ji-Ze Hong (Peter Hong) [this message]
2018-11-15  2:58 ` [V1,1/1] USB: serial: f81534: fix reading old/new IC config Ji-Ze Hong (Peter Hong)
2018-11-20 17:29 ` [PATCH V1 1/1] " Johan Hovold
2018-11-20 17:29   ` [V1,1/1] " Johan Hovold

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1542250724-11667-1-git-send-email-hpeter+linux_kernel@gmail.com \
    --to=hpeter@gmail.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=hpeter+linux_kernel@gmail.com \
    --cc=johan@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=peter_hong@fintek.com.tw \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.