From mboxrd@z Thu Jan 1 00:00:00 1970 From: Abel Vesa Date: Fri, 1 Feb 2019 16:40:22 +0000 Subject: [U-Boot] [PATCH v4 17/20] board: mx6sabreauto: Remove the non-DM code In-Reply-To: <1549039198-16674-1-git-send-email-abel.vesa@nxp.com> References: <1549039198-16674-1-git-send-email-abel.vesa@nxp.com> Message-ID: <1549039198-16674-18-git-send-email-abel.vesa@nxp.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabreauto board file. Signed-off-by: Abel Vesa --- board/freescale/mx6sabreauto/mx6sabreauto.c | 70 ----------------------------- 1 file changed, 70 deletions(-) diff --git a/board/freescale/mx6sabreauto/mx6sabreauto.c b/board/freescale/mx6sabreauto/mx6sabreauto.c index c7e3e67..dd72de9 100644 --- a/board/freescale/mx6sabreauto/mx6sabreauto.c +++ b/board/freescale/mx6sabreauto/mx6sabreauto.c @@ -159,44 +159,6 @@ static iomux_v3_cfg_t const port_exp[] = { IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)), }; -/*Define for building port exp gpio, pin starts from 0*/ -#define PORTEXP_IO_NR(chip, pin) \ - ((chip << 5) + pin) - -/*Get the chip addr from a ioexp gpio*/ -#define PORTEXP_IO_TO_CHIP(gpio_nr) \ - (gpio_nr >> 5) - -/*Get the pin number from a ioexp gpio*/ -#define PORTEXP_IO_TO_PIN(gpio_nr) \ - (gpio_nr & 0x1f) - -static int port_exp_direction_output(unsigned gpio, int value) -{ - int ret; - - i2c_set_bus_num(2); - ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio)); - if (ret) - return ret; - - ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio), - (1 << PORTEXP_IO_TO_PIN(gpio)), - (PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio))); - - if (ret) - return ret; - - ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio), - (1 << PORTEXP_IO_TO_PIN(gpio)), - (value << PORTEXP_IO_TO_PIN(gpio))); - - if (ret) - return ret; - - return 0; -} - #ifdef CONFIG_MTD_NOR_FLASH static iomux_v3_cfg_t const eimnor_pads[] = { IOMUX_PADS(PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)), @@ -681,19 +643,10 @@ int checkboard(void) } #ifdef CONFIG_USB_EHCI_MX6 -#define USB_HOST1_PWR PORTEXP_IO_NR(0x32, 7) -#define USB_OTG_PWR PORTEXP_IO_NR(0x34, 1) - -iomux_v3_cfg_t const usb_otg_pads[] = { - IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)), -}; - int board_ehci_hcd_init(int port) { switch (port) { case 0: - SETUP_IOMUX_PADS(usb_otg_pads); - /* * Set daisy chain for otg_pin_id on 6q. * For 6dl, this bit is reserved. @@ -708,29 +661,6 @@ int board_ehci_hcd_init(int port) } return 0; } - -int board_ehci_power(int port, int on) -{ - switch (port) { - case 0: - if (on) - port_exp_direction_output(USB_OTG_PWR, 1); - else - port_exp_direction_output(USB_OTG_PWR, 0); - break; - case 1: - if (on) - port_exp_direction_output(USB_HOST1_PWR, 1); - else - port_exp_direction_output(USB_HOST1_PWR, 0); - break; - default: - printf("MXC USB port %d not yet supported\n", port); - return -EINVAL; - } - - return 0; -} #endif #ifdef CONFIG_SPL_BUILD -- 2.7.4