From mboxrd@z Thu Jan 1 00:00:00 1970 From: Abel Vesa Date: Fri, 1 Feb 2019 16:40:23 +0000 Subject: [U-Boot] [PATCH v4 18/20] board: mx6sabresd: Remove non-DM code In-Reply-To: <1549039198-16674-1-git-send-email-abel.vesa@nxp.com> References: <1549039198-16674-1-git-send-email-abel.vesa@nxp.com> Message-ID: <1549039198-16674-19-git-send-email-abel.vesa@nxp.com> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Since the mx6sabreauto has DM support, remove the unused non-DM code from mx6sabresd board file. Signed-off-by: Abel Vesa --- board/freescale/mx6sabresd/mx6sabresd.c | 50 --------------------------------- 1 file changed, 50 deletions(-) diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 99002bd..0824a05 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -563,63 +563,13 @@ int board_eth_init(bd_t *bis) } #ifdef CONFIG_USB_EHCI_MX6 -#define USB_OTHERREGS_OFFSET 0x800 -#define UCTRL_PWR_POL (1 << 9) - -static iomux_v3_cfg_t const usb_otg_pads[] = { - IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)), - IOMUX_PADS(PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)), -}; - -static iomux_v3_cfg_t const usb_hc1_pads[] = { - IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)), -}; - static void setup_usb(void) { - SETUP_IOMUX_PADS(usb_otg_pads); - /* * set daisy chain for otg_pin_id on 6q. * for 6dl, this bit is reserved */ imx_iomux_set_gpr_register(1, 13, 1, 0); - - SETUP_IOMUX_PADS(usb_hc1_pads); -} - -int board_ehci_hcd_init(int port) -{ - u32 *usbnc_usb_ctrl; - - if (port > 1) - return -EINVAL; - - usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET + - port * 4); - - setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL); - - return 0; -} - -int board_ehci_power(int port, int on) -{ - switch (port) { - case 0: - break; - case 1: - if (on) - gpio_direction_output(IMX_GPIO_NR(1, 29), 1); - else - gpio_direction_output(IMX_GPIO_NR(1, 29), 0); - break; - default: - printf("MXC USB port %d not yet supported\n", port); - return -EINVAL; - } - - return 0; } #endif -- 2.7.4