* [PATCH 0/7] AM335x Phytec boards update
@ 2019-05-24 13:19 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Hello,
this series adds basic support for phyCORE-AM335x EMMC and
adds device tree for phyBOARD-REGOR AM335x. Also fixes issues
like removing outdated eth phy delay settings and mmc cd active level.
Teresa
Daniel Schultz (1):
ARM: dts: am335x-phycore-som: Add emmc node
Teresa Remmet (6):
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: Add support for phyBOARD-REGOR-AM335x
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-pcm-953.dtsi | 24 +--
arch/arm/boot/dts/am335x-phycore-rdk.dts | 4 +
arch/arm/boot/dts/am335x-phycore-som.dtsi | 47 +++--
arch/arm/boot/dts/am335x-regor-rdk.dts | 24 +++
arch/arm/boot/dts/am335x-regor.dtsi | 223 +++++++++++++++++++++
arch/arm/boot/dts/am335x-wega-rdk.dts | 4 +
arch/arm/boot/dts/am335x-wega.dtsi | 18 +-
9 files changed, 304 insertions(+), 44 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-regor-rdk.dts
create mode 100644 arch/arm/boot/dts/am335x-regor.dtsi
--
2.7.4
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 0/7] AM335x Phytec boards update
@ 2019-05-24 13:19 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Hello,
this series adds basic support for phyCORE-AM335x EMMC and
adds device tree for phyBOARD-REGOR AM335x. Also fixes issues
like removing outdated eth phy delay settings and mmc cd active level.
Teresa
Daniel Schultz (1):
ARM: dts: am335x-phycore-som: Add emmc node
Teresa Remmet (6):
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: Add support for phyBOARD-REGOR-AM335x
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-pcm-953.dtsi | 24 +--
arch/arm/boot/dts/am335x-phycore-rdk.dts | 4 +
arch/arm/boot/dts/am335x-phycore-som.dtsi | 47 +++--
arch/arm/boot/dts/am335x-regor-rdk.dts | 24 +++
arch/arm/boot/dts/am335x-regor.dtsi | 223 +++++++++++++++++++++
arch/arm/boot/dts/am335x-wega-rdk.dts | 4 +
arch/arm/boot/dts/am335x-wega.dtsi | 18 +-
9 files changed, 304 insertions(+), 44 deletions(-)
create mode 100644 arch/arm/boot/dts/am335x-regor-rdk.dts
create mode 100644 arch/arm/boot/dts/am335x-regor.dtsi
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level
2019-05-24 13:19 ` Teresa Remmet
@ 2019-05-24 13:19 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-pcm-953.dtsi | 2 +-
arch/arm/boot/dts/am335x-wega.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
index baceaa7bb33b..20a3d9827692 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -197,7 +197,7 @@
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi
index b7d28a20341f..84581fed3d06 100644
--- a/arch/arm/boot/dts/am335x-wega.dtsi
+++ b/arch/arm/boot/dts/am335x-wega.dtsi
@@ -157,7 +157,7 @@
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level
@ 2019-05-24 13:19 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-pcm-953.dtsi | 2 +-
arch/arm/boot/dts/am335x-wega.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
index baceaa7bb33b..20a3d9827692 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -197,7 +197,7 @@
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi
index b7d28a20341f..84581fed3d06 100644
--- a/arch/arm/boot/dts/am335x-wega.dtsi
+++ b/arch/arm/boot/dts/am335x-wega.dtsi
@@ -157,7 +157,7 @@
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/7] ARM: dts: am335x phytec boards: Remove regulator node
2019-05-24 13:19 ` Teresa Remmet
@ 2019-05-24 13:19 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Move regulators directly to the root node like most am335x boards do.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-phycore-som.dtsi | 18 +++++++-----------
arch/arm/boot/dts/am335x-wega.dtsi | 16 ++++++----------
2 files changed, 13 insertions(+), 21 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index 23c3039c567e..f5b53d30e9a9 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -30,17 +30,13 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- regulators {
- compatible = "simple-bus";
-
- vcc5v: fixedregulator0 {
- compatible = "regulator-fixed";
- regulator-name = "vcc5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-boot-on;
- regulator-always-on;
- };
+ vcc5v: fixedregulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
};
};
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi
index 84581fed3d06..d91ff3e99470 100644
--- a/arch/arm/boot/dts/am335x-wega.dtsi
+++ b/arch/arm/boot/dts/am335x-wega.dtsi
@@ -15,16 +15,12 @@
compatible = "ti,da830-evm-audio";
};
- regulators {
- compatible = "simple-bus";
-
- vcc3v3: fixedregulator1 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
+ vcc3v3: fixedregulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/7] ARM: dts: am335x phytec boards: Remove regulator node
@ 2019-05-24 13:19 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Move regulators directly to the root node like most am335x boards do.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-phycore-som.dtsi | 18 +++++++-----------
arch/arm/boot/dts/am335x-wega.dtsi | 16 ++++++----------
2 files changed, 13 insertions(+), 21 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index 23c3039c567e..f5b53d30e9a9 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -30,17 +30,13 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
- regulators {
- compatible = "simple-bus";
-
- vcc5v: fixedregulator0 {
- compatible = "regulator-fixed";
- regulator-name = "vcc5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-boot-on;
- regulator-always-on;
- };
+ vcc5v: fixedregulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ regulator-always-on;
};
};
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi
index 84581fed3d06..d91ff3e99470 100644
--- a/arch/arm/boot/dts/am335x-wega.dtsi
+++ b/arch/arm/boot/dts/am335x-wega.dtsi
@@ -15,16 +15,12 @@
compatible = "ti,da830-evm-audio";
};
- regulators {
- compatible = "simple-bus";
-
- vcc3v3: fixedregulator1 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
+ vcc3v3: fixedregulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
};
};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/7] ARM: dts: am335x-phycore-som: Add emmc node
2019-05-24 13:19 ` Teresa Remmet
@ 2019-05-24 13:19 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
From: Daniel Schultz <d.schultz@phytec.de>
The phyCORE-AM335x EMMC modules have an EMMC populated and are based
on the phyCORE-AM335x R2 SOM. Therefore, the EMMC node will be added to
the phycore-som devce tree but is by default disabled.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-phycore-som.dtsi | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index f5b53d30e9a9..2bc2265534e1 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -49,6 +49,33 @@
status = "okay";
};
+/* EMMC */
+&am33xx_pinmux {
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+ >;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <8>;
+ ti,non-removable;
+ status = "disabled";
+};
+
/* Ethernet */
&am33xx_pinmux {
ethernet0_pins: pinmux_ethernet0 {
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 3/7] ARM: dts: am335x-phycore-som: Add emmc node
@ 2019-05-24 13:19 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:19 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
From: Daniel Schultz <d.schultz@phytec.de>
The phyCORE-AM335x EMMC modules have an EMMC populated and are based
on the phyCORE-AM335x R2 SOM. Therefore, the EMMC node will be added to
the phycore-som devce tree but is by default disabled.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-phycore-som.dtsi | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index f5b53d30e9a9..2bc2265534e1 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -49,6 +49,33 @@
status = "okay";
};
+/* EMMC */
+&am33xx_pinmux {
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_CSN1, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_CSN2, PIN_INPUT_PULLUP, MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+ >;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>;
+ vmmc-supply = <&vmmc_reg>;
+ bus-width = <8>;
+ ti,non-removable;
+ status = "disabled";
+};
+
/* Ethernet */
&am33xx_pinmux {
ethernet0_pins: pinmux_ethernet0 {
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 4/7] ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
2019-05-24 13:19 ` Teresa Remmet
@ 2019-05-24 13:20 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
As nand flash is not always the primary storage device any more
disable it in the phycore-som include file. Enable it the device tree
files where it is populated.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-phycore-rdk.dts | 4 ++++
arch/arm/boot/dts/am335x-phycore-som.dtsi | 2 +-
arch/arm/boot/dts/am335x-wega-rdk.dts | 4 ++++
3 files changed, 9 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts b/arch/arm/boot/dts/am335x-phycore-rdk.dts
index 305f0b35d6ea..d674d91e18c7 100644
--- a/arch/arm/boot/dts/am335x-phycore-rdk.dts
+++ b/arch/arm/boot/dts/am335x-phycore-rdk.dts
@@ -13,6 +13,10 @@
#include "am335x-pcm-953.dtsi"
/* SoM */
+&gpmc {
+ status = "okay";
+};
+
&i2c_eeprom {
status = "okay";
};
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index 2bc2265534e1..adf04dbefe28 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -190,7 +190,7 @@
};
&gpmc {
- status = "okay";
+ status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&nandflash_pins>;
ranges = <0 0 0x08000000 0x1000000>; /* CS0: NAND */
diff --git a/arch/arm/boot/dts/am335x-wega-rdk.dts b/arch/arm/boot/dts/am335x-wega-rdk.dts
index 6431b7db8109..fd8a844ba780 100644
--- a/arch/arm/boot/dts/am335x-wega-rdk.dts
+++ b/arch/arm/boot/dts/am335x-wega-rdk.dts
@@ -13,6 +13,10 @@
#include "am335x-wega.dtsi"
/* SoM */
+&gpmc {
+ status = "okay";
+};
+
&i2c_eeprom {
status = "okay";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 4/7] ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
@ 2019-05-24 13:20 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
As nand flash is not always the primary storage device any more
disable it in the phycore-som include file. Enable it the device tree
files where it is populated.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-phycore-rdk.dts | 4 ++++
arch/arm/boot/dts/am335x-phycore-som.dtsi | 2 +-
arch/arm/boot/dts/am335x-wega-rdk.dts | 4 ++++
3 files changed, 9 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/am335x-phycore-rdk.dts b/arch/arm/boot/dts/am335x-phycore-rdk.dts
index 305f0b35d6ea..d674d91e18c7 100644
--- a/arch/arm/boot/dts/am335x-phycore-rdk.dts
+++ b/arch/arm/boot/dts/am335x-phycore-rdk.dts
@@ -13,6 +13,10 @@
#include "am335x-pcm-953.dtsi"
/* SoM */
+&gpmc {
+ status = "okay";
+};
+
&i2c_eeprom {
status = "okay";
};
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index 2bc2265534e1..adf04dbefe28 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -190,7 +190,7 @@
};
&gpmc {
- status = "okay";
+ status = "disabled";
pinctrl-names = "default";
pinctrl-0 = <&nandflash_pins>;
ranges = <0 0 0x08000000 0x1000000>; /* CS0: NAND */
diff --git a/arch/arm/boot/dts/am335x-wega-rdk.dts b/arch/arm/boot/dts/am335x-wega-rdk.dts
index 6431b7db8109..fd8a844ba780 100644
--- a/arch/arm/boot/dts/am335x-wega-rdk.dts
+++ b/arch/arm/boot/dts/am335x-wega-rdk.dts
@@ -13,6 +13,10 @@
#include "am335x-wega.dtsi"
/* SoM */
+&gpmc {
+ status = "okay";
+};
+
&i2c_eeprom {
status = "okay";
};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 5/7] ARM: dts: am335x-pcm-953: Update user led names
2019-05-24 13:19 ` Teresa Remmet
@ 2019-05-24 13:20 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Rename user led nodes to match the phytec user leds name scheme.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-pcm-953.dtsi | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
index 20a3d9827692..70fb4a15cad9 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -39,15 +39,13 @@
pinctrl-names = "default";
pinctrl-0 = <&user_leds_pins>;
- green {
- label = "green:user";
+ user-led0 {
gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "gpio";
default-state = "on";
};
- yellow {
- label = "yellow:user";
+ user-led1 {
gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
linux,default-trigger = "gpio";
default-state = "on";
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 5/7] ARM: dts: am335x-pcm-953: Update user led names
@ 2019-05-24 13:20 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Rename user led nodes to match the phytec user leds name scheme.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-pcm-953.dtsi | 6 ++----
1 file changed, 2 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
index 20a3d9827692..70fb4a15cad9 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -39,15 +39,13 @@
pinctrl-names = "default";
pinctrl-0 = <&user_leds_pins>;
- green {
- label = "green:user";
+ user-led0 {
gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "gpio";
default-state = "on";
};
- yellow {
- label = "yellow:user";
+ user-led1 {
gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
linux,default-trigger = "gpio";
default-state = "on";
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 6/7] ARM: dts: am335x-pcm-953: Remove eth phy delay
2019-05-24 13:19 ` Teresa Remmet
` (5 preceding siblings ...)
(?)
@ 2019-05-24 13:20 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Default values fit better than these historical settings.
Hardware layout had been adapted accordingly already in
alpha stage. They did not cause problems for a long time.
Removed values now.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
arch/arm/boot/dts/am335x-pcm-953.dtsi | 16 ----------------
1 file changed, 16 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
index 70fb4a15cad9..dd78db76c877 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -136,22 +136,6 @@
&davinci_mdio {
phy1: ethernet-phy@2 {
reg = <2>;
-
- /* Register 260 (104h) – RGMII Clock and Control Pad Skew */
- rxc-skew-ps = <1400>;
- rxdv-skew-ps = <0>;
- txc-skew-ps = <1400>;
- txen-skew-ps = <0>;
- /* Register 261 (105h) – RGMII RX Data Pad Skew */
- rxd3-skew-ps = <0>;
- rxd2-skew-ps = <0>;
- rxd1-skew-ps = <0>;
- rxd0-skew-ps = <0>;
- /* Register 262 (106h) – RGMII TX Data Pad Skew */
- txd3-skew-ps = <0>;
- txd2-skew-ps = <0>;
- txd1-skew-ps = <0>;
- txd0-skew-ps = <0>;
};
};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 7/7] ARM: dts: Add support for phyBOARD-REGOR-AM335x
2019-05-24 13:19 ` Teresa Remmet
@ 2019-05-24 13:20 ` Teresa Remmet
-1 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Adding support for phyBOARD-REGOR-AM335x:
- CAN
- UART0 / UART2
- RS485
- USB device
- i2c RTC
- SD
- ethernet0 RMII
- ethernet1 MII
- Digital I/Os
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-regor-rdk.dts | 24 +++
arch/arm/boot/dts/am335x-regor.dtsi | 223 +++++++++++++++++++++
4 files changed, 251 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-regor-rdk.dts
create mode 100644 arch/arm/boot/dts/am335x-regor.dtsi
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 1c1e48fd94b5..b301f753ed2c 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -160,6 +160,9 @@ Boards:
- AM335X phyCORE-AM335x: Development kit
compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
+- AM335x phyBOARD-REGOR: Single Board Computer
+ compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx"
+
- AM335X UC-8100-ME-T: Communication-centric industrial computing platform
compatible = "moxa,uc-8100-me-t", "ti,am33xx";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index dab2914fa293..ca42400dc5e8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -748,6 +748,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-pepper.dtb \
am335x-phycore-rdk.dtb \
am335x-pocketbeagle.dtb \
+ am335x-regor-rdk.dtb \
am335x-sancloud-bbe.dtb \
am335x-shc.dtb \
am335x-sbc-t335.dtb \
diff --git a/arch/arm/boot/dts/am335x-regor-rdk.dts b/arch/arm/boot/dts/am335x-regor-rdk.dts
new file mode 100644
index 000000000000..66a1360b83d5
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-regor-rdk.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ *
+ */
+
+/dts-v1/;
+
+#include "am335x-phycore-som.dtsi"
+#include "am335x-regor.dtsi"
+
+/* SoM */
+&gpmc {
+ status = "okay";
+};
+
+&i2c_eeprom {
+ status = "okay";
+};
+
+&serial_flash {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/am335x-regor.dtsi b/arch/arm/boot/dts/am335x-regor.dtsi
new file mode 100644
index 000000000000..5aff02a95766
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-regor.dtsi
@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ *
+ */
+
+/ {
+ model = "Phytec AM335x phyBOARD-REGOR";
+ compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx";
+
+ vcc3v3: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ /* User IO */
+ user_leds: user_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds_pins>;
+
+ run_stop-led {
+ gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "off";
+ };
+
+ error-led {
+ gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "off";
+ };
+ };
+};
+
+/* User Leds */
+&am33xx_pinmux {
+ user_leds_pins: pinmux_user_leds {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* lcd_hsync.gpio2_22 */
+ AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* mcasp0_fsx.gpio3_15 */
+ >;
+ };
+};
+
+/* CAN Busses */
+&am33xx_pinmux {
+ dcan1_pins: pinmux_dcan1 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT_PULLUP, MUX_MODE2) /* uart0_ctsn.d_can1_tx */
+ AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE2) /* uart0_rtsn.d_can1_rx */
+ >;
+ };
+};
+
+&dcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan1_pins>;
+ status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+ ethernet1_pins: pinmux_ethernet1 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT, MUX_MODE1) /* gpmc_a0.mii2_txen */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a1.mii2_rxdv */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT, MUX_MODE1) /* gpmc_a2.mii2_txd3 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT, MUX_MODE1) /* gpmc_a3.mii2_txd2 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT, MUX_MODE1) /* gpmc_a4.mii2_txd1 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE1) /* gpmc_a5.mii2_txd0 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a6.mii2_txclk */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a7.mii2_rxclk */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a8.mii2_rxd3 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a9.mii2_rxd2 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a10.mii2_rxd1 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a11.mii2_rxd0 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_wpn.mii2_rxerr */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_ben1.mii2_col */
+ >;
+ };
+};
+
+&cpsw_emac1 {
+ phy-handle = <&phy1>;
+ phy-mode = "mii";
+ dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mac {
+ slaves = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet0_pins ðernet1_pins>;
+ dual_emac = <1>;
+};
+
+/* GPIOs */
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_gpios_pins>;
+
+ user_gpios_pins: pinmux_user_gpios {
+ pinctrl-single,pins = <
+ /* DIGIN 1-4 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT, MUX_MODE7) /* gpmc_ad11.gpio0_27 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_INPUT, MUX_MODE7) /* gpmc_ad10.gpio0_26 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT, MUX_MODE7) /* gpmc_ad9.gpio0_23 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_INPUT, MUX_MODE7) /* gpmc_ad8.gpio0_22 */
+ /* DIGOUT 1-4 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad15.gpio1_15 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad14.gpio1_14 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad13.gpio1_13 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad12.gpio1_12 */
+ >;
+ };
+};
+
+/* MMC */
+&am33xx_pinmux {
+ mmc1_pins: pinmux_mmc1 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT_PULLUP, MUX_MODE7) /* spi0_cs1.mmc0_sdcd */
+ >;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vcc3v3>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+/* RTC */
+&i2c_rtc {
+ status = "okay";
+};
+
+/* UARTs */
+&am33xx_pinmux {
+ uart0_pins: pinmux_uart0 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+ >;
+ };
+
+ uart2_pins: pinmux_uart2 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLUP, MUX_MODE1) /* mii1_tx_clk.uart2_rxd */
+ AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* mii1_rx_clk.uart2_txd */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+/* RS485 - UART1 */
+&am33xx_pinmux {
+ uart1_rs485_pins: pinmux_uart1_rs485_pins {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLUP, MUX_MODE0)
+ >;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_rs485_pins>;
+ status = "okay";
+ linux,rs485-enabled-at-boot-time;
+};
+
+/* USB */
+&cppi41dma {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 7/7] ARM: dts: Add support for phyBOARD-REGOR-AM335x
@ 2019-05-24 13:20 ` Teresa Remmet
0 siblings, 0 replies; 19+ messages in thread
From: Teresa Remmet @ 2019-05-24 13:20 UTC (permalink / raw)
To: linux-omap, devicetree, linux-arm-kernel
Cc: Tony Lindgren, Mark Rutland, Rob Herring, Daniel Schultz,
Benoît Cousson
Adding support for phyBOARD-REGOR-AM335x:
- CAN
- UART0 / UART2
- RS485
- USB device
- i2c RTC
- SD
- ethernet0 RMII
- ethernet1 MII
- Digital I/Os
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
.../devicetree/bindings/arm/omap/omap.txt | 3 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/am335x-regor-rdk.dts | 24 +++
arch/arm/boot/dts/am335x-regor.dtsi | 223 +++++++++++++++++++++
4 files changed, 251 insertions(+)
create mode 100644 arch/arm/boot/dts/am335x-regor-rdk.dts
create mode 100644 arch/arm/boot/dts/am335x-regor.dtsi
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 1c1e48fd94b5..b301f753ed2c 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -160,6 +160,9 @@ Boards:
- AM335X phyCORE-AM335x: Development kit
compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
+- AM335x phyBOARD-REGOR: Single Board Computer
+ compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx"
+
- AM335X UC-8100-ME-T: Communication-centric industrial computing platform
compatible = "moxa,uc-8100-me-t", "ti,am33xx";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index dab2914fa293..ca42400dc5e8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -748,6 +748,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
am335x-pepper.dtb \
am335x-phycore-rdk.dtb \
am335x-pocketbeagle.dtb \
+ am335x-regor-rdk.dtb \
am335x-sancloud-bbe.dtb \
am335x-shc.dtb \
am335x-sbc-t335.dtb \
diff --git a/arch/arm/boot/dts/am335x-regor-rdk.dts b/arch/arm/boot/dts/am335x-regor-rdk.dts
new file mode 100644
index 000000000000..66a1360b83d5
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-regor-rdk.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ *
+ */
+
+/dts-v1/;
+
+#include "am335x-phycore-som.dtsi"
+#include "am335x-regor.dtsi"
+
+/* SoM */
+&gpmc {
+ status = "okay";
+};
+
+&i2c_eeprom {
+ status = "okay";
+};
+
+&serial_flash {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/am335x-regor.dtsi b/arch/arm/boot/dts/am335x-regor.dtsi
new file mode 100644
index 000000000000..5aff02a95766
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-regor.dtsi
@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Phytec Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ *
+ */
+
+/ {
+ model = "Phytec AM335x phyBOARD-REGOR";
+ compatible = "phytec,am335x-regor", "phytec,am335x-phycore-som", "ti,am33xx";
+
+ vcc3v3: fixedregulator@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ /* User IO */
+ user_leds: user_leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds_pins>;
+
+ run_stop-led {
+ gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "off";
+ };
+
+ error-led {
+ gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "gpio";
+ default-state = "off";
+ };
+ };
+};
+
+/* User Leds */
+&am33xx_pinmux {
+ user_leds_pins: pinmux_user_leds {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* lcd_hsync.gpio2_22 */
+ AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* mcasp0_fsx.gpio3_15 */
+ >;
+ };
+};
+
+/* CAN Busses */
+&am33xx_pinmux {
+ dcan1_pins: pinmux_dcan1 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT_PULLUP, MUX_MODE2) /* uart0_ctsn.d_can1_tx */
+ AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE2) /* uart0_rtsn.d_can1_rx */
+ >;
+ };
+};
+
+&dcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan1_pins>;
+ status = "okay";
+};
+
+/* Ethernet */
+&am33xx_pinmux {
+ ethernet1_pins: pinmux_ethernet1 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT, MUX_MODE1) /* gpmc_a0.mii2_txen */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a1.mii2_rxdv */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT, MUX_MODE1) /* gpmc_a2.mii2_txd3 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT, MUX_MODE1) /* gpmc_a3.mii2_txd2 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT, MUX_MODE1) /* gpmc_a4.mii2_txd1 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT, MUX_MODE1) /* gpmc_a5.mii2_txd0 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a6.mii2_txclk */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a7.mii2_rxclk */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a8.mii2_rxd3 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a9.mii2_rxd2 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a10.mii2_rxd1 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_a11.mii2_rxd0 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_wpn.mii2_rxerr */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_INPUT_PULLDOWN, MUX_MODE1) /* gpmc_ben1.mii2_col */
+ >;
+ };
+};
+
+&cpsw_emac1 {
+ phy-handle = <&phy1>;
+ phy-mode = "mii";
+ dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&mac {
+ slaves = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet0_pins ðernet1_pins>;
+ dual_emac = <1>;
+};
+
+/* GPIOs */
+&am33xx_pinmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_gpios_pins>;
+
+ user_gpios_pins: pinmux_user_gpios {
+ pinctrl-single,pins = <
+ /* DIGIN 1-4 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT, MUX_MODE7) /* gpmc_ad11.gpio0_27 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_INPUT, MUX_MODE7) /* gpmc_ad10.gpio0_26 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD9, PIN_INPUT, MUX_MODE7) /* gpmc_ad9.gpio0_23 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD8, PIN_INPUT, MUX_MODE7) /* gpmc_ad8.gpio0_22 */
+ /* DIGOUT 1-4 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad15.gpio1_15 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad14.gpio1_14 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad13.gpio1_13 */
+ AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_OUTPUT, MUX_MODE7) /* gpmc_ad12.gpio1_12 */
+ >;
+ };
+};
+
+/* MMC */
+&am33xx_pinmux {
+ mmc1_pins: pinmux_mmc1 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_SPI0_CS1, PIN_INPUT_PULLUP, MUX_MODE7) /* spi0_cs1.mmc0_sdcd */
+ >;
+ };
+};
+
+&mmc1 {
+ vmmc-supply = <&vcc3v3>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+/* RTC */
+&i2c_rtc {
+ status = "okay";
+};
+
+/* UARTs */
+&am33xx_pinmux {
+ uart0_pins: pinmux_uart0 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+ >;
+ };
+
+ uart2_pins: pinmux_uart2 {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLUP, MUX_MODE1) /* mii1_tx_clk.uart2_rxd */
+ AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE1) /* mii1_rx_clk.uart2_txd */
+ >;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "okay";
+};
+
+/* RS485 - UART1 */
+&am33xx_pinmux {
+ uart1_rs485_pins: pinmux_uart1_rs485_pins {
+ pinctrl-single,pins = <
+ AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+ AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLUP, MUX_MODE0)
+ >;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_rs485_pins>;
+ status = "okay";
+ linux,rs485-enabled-at-boot-time;
+};
+
+/* USB */
+&cppi41dma {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level
2019-05-24 13:19 ` Teresa Remmet
@ 2019-06-10 7:07 ` Tony Lindgren
-1 siblings, 0 replies; 19+ messages in thread
From: Tony Lindgren @ 2019-06-10 7:07 UTC (permalink / raw)
To: Teresa Remmet
Cc: Mark Rutland, devicetree, Daniel Schultz, Rob Herring,
Benoît Cousson, linux-omap, linux-arm-kernel
* Teresa Remmet <t.remmet@phytec.de> [190524 06:20]:
> Active level of the mmc1 cd gpio needs to be low instead of high.
> Fix PCM-953 and phyBOARD-WEGA.
Thanks I'll pick this patch into fixes.
Regards,
Tony
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level
@ 2019-06-10 7:07 ` Tony Lindgren
0 siblings, 0 replies; 19+ messages in thread
From: Tony Lindgren @ 2019-06-10 7:07 UTC (permalink / raw)
To: Teresa Remmet
Cc: Mark Rutland, devicetree, Daniel Schultz, Rob Herring,
Benoît Cousson, linux-omap, linux-arm-kernel
* Teresa Remmet <t.remmet@phytec.de> [190524 06:20]:
> Active level of the mmc1 cd gpio needs to be low instead of high.
> Fix PCM-953 and phyBOARD-WEGA.
Thanks I'll pick this patch into fixes.
Regards,
Tony
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level
2019-06-10 7:07 ` Tony Lindgren
@ 2019-06-10 12:10 ` Tony Lindgren
-1 siblings, 0 replies; 19+ messages in thread
From: Tony Lindgren @ 2019-06-10 12:10 UTC (permalink / raw)
To: Teresa Remmet
Cc: Mark Rutland, devicetree, Daniel Schultz, Rob Herring,
Benoît Cousson, linux-omap, linux-arm-kernel
* Tony Lindgren <tony@atomide.com> [190610 07:08]:
> * Teresa Remmet <t.remmet@phytec.de> [190524 06:20]:
> > Active level of the mmc1 cd gpio needs to be low instead of high.
> > Fix PCM-953 and phyBOARD-WEGA.
>
> Thanks I'll pick this patch into fixes.
And I'll apply the rest of the series into omap-for-v5.3/dt.
Thanks,
Tony
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level
@ 2019-06-10 12:10 ` Tony Lindgren
0 siblings, 0 replies; 19+ messages in thread
From: Tony Lindgren @ 2019-06-10 12:10 UTC (permalink / raw)
To: Teresa Remmet
Cc: Mark Rutland, devicetree, Daniel Schultz, Rob Herring,
Benoît Cousson, linux-omap, linux-arm-kernel
* Tony Lindgren <tony@atomide.com> [190610 07:08]:
> * Teresa Remmet <t.remmet@phytec.de> [190524 06:20]:
> > Active level of the mmc1 cd gpio needs to be low instead of high.
> > Fix PCM-953 and phyBOARD-WEGA.
>
> Thanks I'll pick this patch into fixes.
And I'll apply the rest of the series into omap-for-v5.3/dt.
Thanks,
Tony
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2019-06-10 12:10 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-05-24 13:19 [PATCH 0/7] AM335x Phytec boards update Teresa Remmet
2019-05-24 13:19 ` Teresa Remmet
2019-05-24 13:19 ` [PATCH 1/7] ARM: dts: am335x phytec boards: Fix cd-gpios active level Teresa Remmet
2019-05-24 13:19 ` Teresa Remmet
2019-06-10 7:07 ` Tony Lindgren
2019-06-10 7:07 ` Tony Lindgren
2019-06-10 12:10 ` Tony Lindgren
2019-06-10 12:10 ` Tony Lindgren
2019-05-24 13:19 ` [PATCH 2/7] ARM: dts: am335x phytec boards: Remove regulator node Teresa Remmet
2019-05-24 13:19 ` Teresa Remmet
2019-05-24 13:19 ` [PATCH 3/7] ARM: dts: am335x-phycore-som: Add emmc node Teresa Remmet
2019-05-24 13:19 ` Teresa Remmet
2019-05-24 13:20 ` [PATCH 4/7] ARM: dts: am335x-phycore-som: Enable gpmc node in dts files Teresa Remmet
2019-05-24 13:20 ` Teresa Remmet
2019-05-24 13:20 ` [PATCH 5/7] ARM: dts: am335x-pcm-953: Update user led names Teresa Remmet
2019-05-24 13:20 ` Teresa Remmet
2019-05-24 13:20 ` [PATCH 6/7] ARM: dts: am335x-pcm-953: Remove eth phy delay Teresa Remmet
2019-05-24 13:20 ` [PATCH 7/7] ARM: dts: Add support for phyBOARD-REGOR-AM335x Teresa Remmet
2019-05-24 13:20 ` Teresa Remmet
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.