[PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[Kunihiko Hayashi]

This series adds some improvements to PHY interface drivers, and adds legacy SoC
support that needs to manage gio clock and reset.

Kunihiko Hayashi (6):
  phy: socionext: Use devm_platform_ioremap_resource()
  dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from
    usb3-hsphy
  phy: uniphier-usb3ss: Add Pro5 support
  phy: uniphier-usb3hs: Add legacy SoC support for Pro5
  phy: uniphier-usb3hs: Change Rx sync mode to avoid communication
    failure
  phy: uniphier-pcie: Add legacy SoC support for Pro5

 .../devicetree/bindings/phy/uniphier-pcie-phy.txt  | 13 ++-
 .../bindings/phy/uniphier-usb3-hsphy.txt           |  6 +-
 .../bindings/phy/uniphier-usb3-ssphy.txt           |  5 +-
 drivers/phy/socionext/phy-uniphier-pcie.c          | 87 ++++++++++++++++----
 drivers/phy/socionext/phy-uniphier-usb3hs.c        | 92 ++++++++++++++++------
 drivers/phy/socionext/phy-uniphier-usb3ss.c        |  8 +-
 6 files changed, 163 insertions(+), 48 deletions(-)

-- 
2.7.4

[PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[Kunihiko Hayashi]

This series adds some improvements to PHY interface drivers, and adds legacy SoC
support that needs to manage gio clock and reset.

Kunihiko Hayashi (6):
  phy: socionext: Use devm_platform_ioremap_resource()
  dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from
    usb3-hsphy
  phy: uniphier-usb3ss: Add Pro5 support
  phy: uniphier-usb3hs: Add legacy SoC support for Pro5
  phy: uniphier-usb3hs: Change Rx sync mode to avoid communication
    failure
  phy: uniphier-pcie: Add legacy SoC support for Pro5

 .../devicetree/bindings/phy/uniphier-pcie-phy.txt  | 13 ++-
 .../bindings/phy/uniphier-usb3-hsphy.txt           |  6 +-
 .../bindings/phy/uniphier-usb3-ssphy.txt           |  5 +-
 drivers/phy/socionext/phy-uniphier-pcie.c          | 87 ++++++++++++++++----
 drivers/phy/socionext/phy-uniphier-usb3hs.c        | 92 ++++++++++++++++------
 drivers/phy/socionext/phy-uniphier-usb3ss.c        |  8 +-
 6 files changed, 163 insertions(+), 48 deletions(-)

-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/6] phy: socionext: Use devm_platform_ioremap_resource()

[Kunihiko Hayashi]

Use devm_platform_ioremap_resource() to simplify the code.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-pcie.c   | 4 +---
 drivers/phy/socionext/phy-uniphier-usb3hs.c | 4 +---
 drivers/phy/socionext/phy-uniphier-usb3ss.c | 4 +---
 3 files changed, 3 insertions(+), 9 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-pcie.c b/drivers/phy/socionext/phy-uniphier-pcie.c
index 93ffbd2..25d1d9d 100644
--- a/drivers/phy/socionext/phy-uniphier-pcie.c
+++ b/drivers/phy/socionext/phy-uniphier-pcie.c
@@ -163,7 +163,6 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 	struct phy_provider *phy_provider;
 	struct device *dev = &pdev->dev;
 	struct regmap *regmap;
-	struct resource *res;
 	struct phy *phy;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -176,8 +175,7 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 
 	priv->dev = dev;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
diff --git a/drivers/phy/socionext/phy-uniphier-usb3hs.c b/drivers/phy/socionext/phy-uniphier-usb3hs.c
index 50f379f..1d3f9e8 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3hs.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3hs.c
@@ -309,7 +309,6 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct uniphier_u3hsphy_priv *priv;
 	struct phy_provider *phy_provider;
-	struct resource *res;
 	struct phy *phy;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -322,8 +321,7 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 		    priv->data->nparams > MAX_PHY_PARAMS))
 		return -EINVAL;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
diff --git a/drivers/phy/socionext/phy-uniphier-usb3ss.c b/drivers/phy/socionext/phy-uniphier-usb3ss.c
index ec231e4..05e40a2 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3ss.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3ss.c
@@ -215,7 +215,6 @@ static int uniphier_u3ssphy_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct uniphier_u3ssphy_priv *priv;
 	struct phy_provider *phy_provider;
-	struct resource *res;
 	struct phy *phy;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -228,8 +227,7 @@ static int uniphier_u3ssphy_probe(struct platform_device *pdev)
 		    priv->data->nparams > MAX_PHY_PARAMS))
 		return -EINVAL;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-- 
2.7.4

[PATCH 1/6] phy: socionext: Use devm_platform_ioremap_resource()

[Kunihiko Hayashi]

Use devm_platform_ioremap_resource() to simplify the code.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-pcie.c   | 4 +---
 drivers/phy/socionext/phy-uniphier-usb3hs.c | 4 +---
 drivers/phy/socionext/phy-uniphier-usb3ss.c | 4 +---
 3 files changed, 3 insertions(+), 9 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-pcie.c b/drivers/phy/socionext/phy-uniphier-pcie.c
index 93ffbd2..25d1d9d 100644
--- a/drivers/phy/socionext/phy-uniphier-pcie.c
+++ b/drivers/phy/socionext/phy-uniphier-pcie.c
@@ -163,7 +163,6 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 	struct phy_provider *phy_provider;
 	struct device *dev = &pdev->dev;
 	struct regmap *regmap;
-	struct resource *res;
 	struct phy *phy;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -176,8 +175,7 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 
 	priv->dev = dev;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
diff --git a/drivers/phy/socionext/phy-uniphier-usb3hs.c b/drivers/phy/socionext/phy-uniphier-usb3hs.c
index 50f379f..1d3f9e8 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3hs.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3hs.c
@@ -309,7 +309,6 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct uniphier_u3hsphy_priv *priv;
 	struct phy_provider *phy_provider;
-	struct resource *res;
 	struct phy *phy;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -322,8 +321,7 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 		    priv->data->nparams > MAX_PHY_PARAMS))
 		return -EINVAL;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
diff --git a/drivers/phy/socionext/phy-uniphier-usb3ss.c b/drivers/phy/socionext/phy-uniphier-usb3ss.c
index ec231e4..05e40a2 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3ss.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3ss.c
@@ -215,7 +215,6 @@ static int uniphier_u3ssphy_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct uniphier_u3ssphy_priv *priv;
 	struct phy_provider *phy_provider;
-	struct resource *res;
 	struct phy *phy;
 
 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -228,8 +227,7 @@ static int uniphier_u3ssphy_probe(struct platform_device *pdev)
 		    priv->data->nparams > MAX_PHY_PARAMS))
 		return -EINVAL;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	priv->base = devm_ioremap_resource(dev, res);
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/6] dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from usb3-hsphy

[Kunihiko Hayashi]

This adds compatible string for Pro5 SoC that needs to manage gio clock
and reset. And Pro4 SoC uses USB2 PHY instead of USB3 HS-PHY, so this
removes Pro4 description from usb3-hsphy.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt | 13 +++++++++----
 .../devicetree/bindings/phy/uniphier-usb3-hsphy.txt         |  6 +++---
 .../devicetree/bindings/phy/uniphier-usb3-ssphy.txt         |  5 +++--
 3 files changed, 15 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt
index 1889d3b..3cee372 100644
--- a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt
+++ b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt
@@ -5,14 +5,19 @@ PCIe controller implemented on Socionext UniPhier SoCs.
 
 Required properties:
 - compatible: Should contain one of the following:
+    "socionext,uniphier-pro5-pcie-phy" - for Pro5 PHY
     "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY
     "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY
 - reg: Specifies offset and length of the register set for the device.
 - #phy-cells: Must be zero.
-- clocks: A phandle to the clock gate for PCIe glue layer including
-	this phy.
-- resets: A phandle to the reset line for PCIe glue layer including
-	this phy.
+- clocks: A list of phandles to the clock gate for PCIe glue layer
+	including this phy.
+- clock-names: For Pro5 only, should contain the following:
+    "gio", "link" - for Pro5 SoC
+- resets: A list of phandles to the reset line for PCIe glue layer
+	including this phy.
+- reset-names: For Pro5 only, should contain the following:
+    "gio", "link" - for Pro5 SoC
 
 Optional properties:
 - socionext,syscon: A phandle to system control to set configurations
diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
index e8d8086..093d4f0 100644
--- a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
+++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
@@ -7,7 +7,7 @@ this describes about High-Speed PHY.
 
 Required properties:
 - compatible: Should contain one of the following:
-    "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC
+    "socionext,uniphier-pro5-usb3-hsphy" - for Pro5 SoC
     "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC
     "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC
     "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC
@@ -16,13 +16,13 @@ Required properties:
 - clocks: A list of phandles to the clock gate for USB3 glue layer.
 	According to the clock-names, appropriate clocks are required.
 - clock-names: Should contain the following:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro5 SoC
     "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
     "phy", "link" - for others
 - resets: A list of phandles to the reset control for USB3 glue layer.
 	According to the reset-names, appropriate resets are required.
 - reset-names: Should contain the following:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro5 SoC
     "phy", "link" - for others
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
index 490b815..9df2bc2 100644
--- a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
+++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
@@ -8,6 +8,7 @@ this describes about Super-Speed PHY.
 Required properties:
 - compatible: Should contain one of the following:
     "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC
+    "socionext,uniphier-pro5-usb3-ssphy" - for Pro5 SoC
     "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC
     "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC
     "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC
@@ -16,13 +17,13 @@ Required properties:
 - clocks: A list of phandles to the clock gate for USB3 glue layer.
 	According to the clock-names, appropriate clocks are required.
 - clock-names:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro4 and Pro5 SoC
     "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
     "phy", "link" - for others
 - resets: A list of phandles to the reset control for USB3 glue layer.
 	According to the reset-names, appropriate resets are required.
 - reset-names:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro4 and Pro5 SoC
     "phy", "link" - for others
 
 Optional properties:
-- 
2.7.4

[PATCH 2/6] dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from usb3-hsphy

[Kunihiko Hayashi]

This adds compatible string for Pro5 SoC that needs to manage gio clock
and reset. And Pro4 SoC uses USB2 PHY instead of USB3 HS-PHY, so this
removes Pro4 description from usb3-hsphy.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt | 13 +++++++++----
 .../devicetree/bindings/phy/uniphier-usb3-hsphy.txt         |  6 +++---
 .../devicetree/bindings/phy/uniphier-usb3-ssphy.txt         |  5 +++--
 3 files changed, 15 insertions(+), 9 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt
index 1889d3b..3cee372 100644
--- a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt
+++ b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt
@@ -5,14 +5,19 @@ PCIe controller implemented on Socionext UniPhier SoCs.
 
 Required properties:
 - compatible: Should contain one of the following:
+    "socionext,uniphier-pro5-pcie-phy" - for Pro5 PHY
     "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY
     "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY
 - reg: Specifies offset and length of the register set for the device.
 - #phy-cells: Must be zero.
-- clocks: A phandle to the clock gate for PCIe glue layer including
-	this phy.
-- resets: A phandle to the reset line for PCIe glue layer including
-	this phy.
+- clocks: A list of phandles to the clock gate for PCIe glue layer
+	including this phy.
+- clock-names: For Pro5 only, should contain the following:
+    "gio", "link" - for Pro5 SoC
+- resets: A list of phandles to the reset line for PCIe glue layer
+	including this phy.
+- reset-names: For Pro5 only, should contain the following:
+    "gio", "link" - for Pro5 SoC
 
 Optional properties:
 - socionext,syscon: A phandle to system control to set configurations
diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
index e8d8086..093d4f0 100644
--- a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
+++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
@@ -7,7 +7,7 @@ this describes about High-Speed PHY.
 
 Required properties:
 - compatible: Should contain one of the following:
-    "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC
+    "socionext,uniphier-pro5-usb3-hsphy" - for Pro5 SoC
     "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC
     "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC
     "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC
@@ -16,13 +16,13 @@ Required properties:
 - clocks: A list of phandles to the clock gate for USB3 glue layer.
 	According to the clock-names, appropriate clocks are required.
 - clock-names: Should contain the following:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro5 SoC
     "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
     "phy", "link" - for others
 - resets: A list of phandles to the reset control for USB3 glue layer.
 	According to the reset-names, appropriate resets are required.
 - reset-names: Should contain the following:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro5 SoC
     "phy", "link" - for others
 
 Optional properties:
diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
index 490b815..9df2bc2 100644
--- a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
+++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
@@ -8,6 +8,7 @@ this describes about Super-Speed PHY.
 Required properties:
 - compatible: Should contain one of the following:
     "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC
+    "socionext,uniphier-pro5-usb3-ssphy" - for Pro5 SoC
     "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC
     "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC
     "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC
@@ -16,13 +17,13 @@ Required properties:
 - clocks: A list of phandles to the clock gate for USB3 glue layer.
 	According to the clock-names, appropriate clocks are required.
 - clock-names:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro4 and Pro5 SoC
     "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
     "phy", "link" - for others
 - resets: A list of phandles to the reset control for USB3 glue layer.
 	According to the reset-names, appropriate resets are required.
 - reset-names:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro4 and Pro5 SoC
     "phy", "link" - for others
 
 Optional properties:
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/6] phy: uniphier-usb3ss: Add Pro5 support

[Kunihiko Hayashi]

Pro5 SoC has same scheme of USB3 ss-phy as Pro4, so the data for Pro5 is
equivalent to Pro4.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-usb3ss.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/phy/socionext/phy-uniphier-usb3ss.c b/drivers/phy/socionext/phy-uniphier-usb3ss.c
index 05e40a2..6700645 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3ss.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3ss.c
@@ -313,6 +313,10 @@ static const struct of_device_id uniphier_u3ssphy_match[] = {
 		.data = &uniphier_pro4_data,
 	},
 	{
+		.compatible = "socionext,uniphier-pro5-usb3-ssphy",
+		.data = &uniphier_pro4_data,
+	},
+	{
 		.compatible = "socionext,uniphier-pxs2-usb3-ssphy",
 		.data = &uniphier_pxs2_data,
 	},
-- 
2.7.4

[PATCH 3/6] phy: uniphier-usb3ss: Add Pro5 support

[Kunihiko Hayashi]

Pro5 SoC has same scheme of USB3 ss-phy as Pro4, so the data for Pro5 is
equivalent to Pro4.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-usb3ss.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/phy/socionext/phy-uniphier-usb3ss.c b/drivers/phy/socionext/phy-uniphier-usb3ss.c
index 05e40a2..6700645 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3ss.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3ss.c
@@ -313,6 +313,10 @@ static const struct of_device_id uniphier_u3ssphy_match[] = {
 		.data = &uniphier_pro4_data,
 	},
 	{
+		.compatible = "socionext,uniphier-pro5-usb3-ssphy",
+		.data = &uniphier_pro4_data,
+	},
+	{
 		.compatible = "socionext,uniphier-pxs2-usb3-ssphy",
 		.data = &uniphier_pxs2_data,
 	},
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/6] phy: uniphier-usb3hs: Add legacy SoC support for Pro5

[Kunihiko Hayashi]

Add legacy SoC support that needs to manage gio clock and reset.
This supports Pro5.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-usb3hs.c | 68 ++++++++++++++++++++++-------
 1 file changed, 53 insertions(+), 15 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-usb3hs.c b/drivers/phy/socionext/phy-uniphier-usb3hs.c
index 1d3f9e8..bdf696e 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3hs.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3hs.c
@@ -66,13 +66,14 @@ struct uniphier_u3hsphy_trim_param {
 struct uniphier_u3hsphy_priv {
 	struct device *dev;
 	void __iomem *base;
-	struct clk *clk, *clk_parent, *clk_ext;
-	struct reset_control *rst, *rst_parent;
+	struct clk *clk, *clk_parent, *clk_ext, *clk_parent_gio;
+	struct reset_control *rst, *rst_parent, *rst_parent_gio;
 	struct regulator *vbus;
 	const struct uniphier_u3hsphy_soc_data *data;
 };
 
 struct uniphier_u3hsphy_soc_data {
+	bool is_legacy;
 	int nparams;
 	const struct uniphier_u3hsphy_param param[MAX_PHY_PARAMS];
 	u32 config0;
@@ -256,11 +257,20 @@ static int uniphier_u3hsphy_init(struct phy *phy)
 	if (ret)
 		return ret;
 
-	ret = reset_control_deassert(priv->rst_parent);
+	ret = clk_prepare_enable(priv->clk_parent_gio);
 	if (ret)
 		goto out_clk_disable;
 
-	if (!priv->data->config0 && !priv->data->config1)
+	ret = reset_control_deassert(priv->rst_parent);
+	if (ret)
+		goto out_clk_gio_disable;
+
+	ret = reset_control_deassert(priv->rst_parent_gio);
+	if (ret)
+		goto out_rst_assert;
+
+	if ((priv->data->is_legacy)
+	    || (!priv->data->config0 && !priv->data->config1))
 		return 0;
 
 	config0 = priv->data->config0;
@@ -280,6 +290,8 @@ static int uniphier_u3hsphy_init(struct phy *phy)
 
 out_rst_assert:
 	reset_control_assert(priv->rst_parent);
+out_clk_gio_disable:
+	clk_disable_unprepare(priv->clk_parent_gio);
 out_clk_disable:
 	clk_disable_unprepare(priv->clk_parent);
 
@@ -290,7 +302,9 @@ static int uniphier_u3hsphy_exit(struct phy *phy)
 {
 	struct uniphier_u3hsphy_priv *priv = phy_get_drvdata(phy);
 
+	reset_control_assert(priv->rst_parent_gio);
 	reset_control_assert(priv->rst_parent);
+	clk_disable_unprepare(priv->clk_parent_gio);
 	clk_disable_unprepare(priv->clk_parent);
 
 	return 0;
@@ -325,22 +339,34 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-	priv->clk = devm_clk_get(dev, "phy");
-	if (IS_ERR(priv->clk))
-		return PTR_ERR(priv->clk);
+	if (!priv->data->is_legacy) {
+		priv->clk = devm_clk_get(dev, "phy");
+		if (IS_ERR(priv->clk))
+			return PTR_ERR(priv->clk);
+
+		priv->clk_ext = devm_clk_get_optional(dev, "phy-ext");
+		if (IS_ERR(priv->clk_ext))
+			return PTR_ERR(priv->clk_ext);
+
+		priv->rst = devm_reset_control_get_shared(dev, "phy");
+		if (IS_ERR(priv->rst))
+			return PTR_ERR(priv->rst);
+
+	} else {
+		priv->clk_parent_gio = devm_clk_get(dev, "gio");
+		if (IS_ERR(priv->clk_parent_gio))
+			return PTR_ERR(priv->clk_parent_gio);
+
+		priv->rst_parent_gio =
+			devm_reset_control_get_shared(dev, "gio");
+		if (IS_ERR(priv->rst_parent_gio))
+			return PTR_ERR(priv->rst_parent_gio);
+	}
 
 	priv->clk_parent = devm_clk_get(dev, "link");
 	if (IS_ERR(priv->clk_parent))
 		return PTR_ERR(priv->clk_parent);
 
-	priv->clk_ext = devm_clk_get_optional(dev, "phy-ext");
-	if (IS_ERR(priv->clk_ext))
-		return PTR_ERR(priv->clk_ext);
-
-	priv->rst = devm_reset_control_get_shared(dev, "phy");
-	if (IS_ERR(priv->rst))
-		return PTR_ERR(priv->rst);
-
 	priv->rst_parent = devm_reset_control_get_shared(dev, "link");
 	if (IS_ERR(priv->rst_parent))
 		return PTR_ERR(priv->rst_parent);
@@ -362,11 +388,18 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
+static const struct uniphier_u3hsphy_soc_data uniphier_pro5_data = {
+	.is_legacy = true,
+	.nparams = 0,
+};
+
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs2_data = {
+	.is_legacy = false,
 	.nparams = 0,
 };
 
 static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
+	.is_legacy = false,
 	.nparams = 2,
 	.param = {
 		{ LS_SLEW, 1 },
@@ -378,6 +411,7 @@ static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
 };
 
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs3_data = {
+	.is_legacy = false,
 	.nparams = 0,
 	.trim_func = uniphier_u3hsphy_trim_ld20,
 	.config0 = 0x92316680,
@@ -386,6 +420,10 @@ static const struct uniphier_u3hsphy_soc_data uniphier_pxs3_data = {
 
 static const struct of_device_id uniphier_u3hsphy_match[] = {
 	{
+		.compatible = "socionext,uniphier-pro5-usb3-hsphy",
+		.data = &uniphier_pro5_data,
+	},
+	{
 		.compatible = "socionext,uniphier-pxs2-usb3-hsphy",
 		.data = &uniphier_pxs2_data,
 	},
-- 
2.7.4

[PATCH 4/6] phy: uniphier-usb3hs: Add legacy SoC support for Pro5

[Kunihiko Hayashi]

Add legacy SoC support that needs to manage gio clock and reset.
This supports Pro5.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-usb3hs.c | 68 ++++++++++++++++++++++-------
 1 file changed, 53 insertions(+), 15 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-usb3hs.c b/drivers/phy/socionext/phy-uniphier-usb3hs.c
index 1d3f9e8..bdf696e 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3hs.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3hs.c
@@ -66,13 +66,14 @@ struct uniphier_u3hsphy_trim_param {
 struct uniphier_u3hsphy_priv {
 	struct device *dev;
 	void __iomem *base;
-	struct clk *clk, *clk_parent, *clk_ext;
-	struct reset_control *rst, *rst_parent;
+	struct clk *clk, *clk_parent, *clk_ext, *clk_parent_gio;
+	struct reset_control *rst, *rst_parent, *rst_parent_gio;
 	struct regulator *vbus;
 	const struct uniphier_u3hsphy_soc_data *data;
 };
 
 struct uniphier_u3hsphy_soc_data {
+	bool is_legacy;
 	int nparams;
 	const struct uniphier_u3hsphy_param param[MAX_PHY_PARAMS];
 	u32 config0;
@@ -256,11 +257,20 @@ static int uniphier_u3hsphy_init(struct phy *phy)
 	if (ret)
 		return ret;
 
-	ret = reset_control_deassert(priv->rst_parent);
+	ret = clk_prepare_enable(priv->clk_parent_gio);
 	if (ret)
 		goto out_clk_disable;
 
-	if (!priv->data->config0 && !priv->data->config1)
+	ret = reset_control_deassert(priv->rst_parent);
+	if (ret)
+		goto out_clk_gio_disable;
+
+	ret = reset_control_deassert(priv->rst_parent_gio);
+	if (ret)
+		goto out_rst_assert;
+
+	if ((priv->data->is_legacy)
+	    || (!priv->data->config0 && !priv->data->config1))
 		return 0;
 
 	config0 = priv->data->config0;
@@ -280,6 +290,8 @@ static int uniphier_u3hsphy_init(struct phy *phy)
 
 out_rst_assert:
 	reset_control_assert(priv->rst_parent);
+out_clk_gio_disable:
+	clk_disable_unprepare(priv->clk_parent_gio);
 out_clk_disable:
 	clk_disable_unprepare(priv->clk_parent);
 
@@ -290,7 +302,9 @@ static int uniphier_u3hsphy_exit(struct phy *phy)
 {
 	struct uniphier_u3hsphy_priv *priv = phy_get_drvdata(phy);
 
+	reset_control_assert(priv->rst_parent_gio);
 	reset_control_assert(priv->rst_parent);
+	clk_disable_unprepare(priv->clk_parent_gio);
 	clk_disable_unprepare(priv->clk_parent);
 
 	return 0;
@@ -325,22 +339,34 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-	priv->clk = devm_clk_get(dev, "phy");
-	if (IS_ERR(priv->clk))
-		return PTR_ERR(priv->clk);
+	if (!priv->data->is_legacy) {
+		priv->clk = devm_clk_get(dev, "phy");
+		if (IS_ERR(priv->clk))
+			return PTR_ERR(priv->clk);
+
+		priv->clk_ext = devm_clk_get_optional(dev, "phy-ext");
+		if (IS_ERR(priv->clk_ext))
+			return PTR_ERR(priv->clk_ext);
+
+		priv->rst = devm_reset_control_get_shared(dev, "phy");
+		if (IS_ERR(priv->rst))
+			return PTR_ERR(priv->rst);
+
+	} else {
+		priv->clk_parent_gio = devm_clk_get(dev, "gio");
+		if (IS_ERR(priv->clk_parent_gio))
+			return PTR_ERR(priv->clk_parent_gio);
+
+		priv->rst_parent_gio =
+			devm_reset_control_get_shared(dev, "gio");
+		if (IS_ERR(priv->rst_parent_gio))
+			return PTR_ERR(priv->rst_parent_gio);
+	}
 
 	priv->clk_parent = devm_clk_get(dev, "link");
 	if (IS_ERR(priv->clk_parent))
 		return PTR_ERR(priv->clk_parent);
 
-	priv->clk_ext = devm_clk_get_optional(dev, "phy-ext");
-	if (IS_ERR(priv->clk_ext))
-		return PTR_ERR(priv->clk_ext);
-
-	priv->rst = devm_reset_control_get_shared(dev, "phy");
-	if (IS_ERR(priv->rst))
-		return PTR_ERR(priv->rst);
-
 	priv->rst_parent = devm_reset_control_get_shared(dev, "link");
 	if (IS_ERR(priv->rst_parent))
 		return PTR_ERR(priv->rst_parent);
@@ -362,11 +388,18 @@ static int uniphier_u3hsphy_probe(struct platform_device *pdev)
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
+static const struct uniphier_u3hsphy_soc_data uniphier_pro5_data = {
+	.is_legacy = true,
+	.nparams = 0,
+};
+
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs2_data = {
+	.is_legacy = false,
 	.nparams = 0,
 };
 
 static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
+	.is_legacy = false,
 	.nparams = 2,
 	.param = {
 		{ LS_SLEW, 1 },
@@ -378,6 +411,7 @@ static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
 };
 
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs3_data = {
+	.is_legacy = false,
 	.nparams = 0,
 	.trim_func = uniphier_u3hsphy_trim_ld20,
 	.config0 = 0x92316680,
@@ -386,6 +420,10 @@ static const struct uniphier_u3hsphy_soc_data uniphier_pxs3_data = {
 
 static const struct of_device_id uniphier_u3hsphy_match[] = {
 	{
+		.compatible = "socionext,uniphier-pro5-usb3-hsphy",
+		.data = &uniphier_pro5_data,
+	},
+	{
 		.compatible = "socionext,uniphier-pxs2-usb3-hsphy",
 		.data = &uniphier_pxs2_data,
 	},
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/6] phy: uniphier-usb3hs: Change Rx sync mode to avoid communication failure

[Kunihiko Hayashi]

In case of using default parameters, communication failure might occur
in rare cases. This sets Rx sync mode parameter to avoid the issue.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-usb3hs.c | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-usb3hs.c b/drivers/phy/socionext/phy-uniphier-usb3hs.c
index bdf696e..a9bc741 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3hs.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3hs.c
@@ -41,10 +41,12 @@
 
 #define PHY_F(regno, msb, lsb) { (regno), (msb), (lsb) }
 
+#define RX_CHK_SYNC	PHY_F(0, 5, 5)	/* RX sync mode */
+#define RX_SYNC_SEL	PHY_F(1, 1, 0)	/* RX sync length */
 #define LS_SLEW		PHY_F(10, 6, 6)	/* LS mode slew rate */
 #define FS_LS_DRV	PHY_F(10, 5, 5)	/* FS/LS slew rate */
 
-#define MAX_PHY_PARAMS	2
+#define MAX_PHY_PARAMS	4
 
 struct uniphier_u3hsphy_param {
 	struct {
@@ -395,13 +397,19 @@ static const struct uniphier_u3hsphy_soc_data uniphier_pro5_data = {
 
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs2_data = {
 	.is_legacy = false,
-	.nparams = 0,
+	.nparams = 2,
+	.param = {
+		{ RX_CHK_SYNC, 1 },
+		{ RX_SYNC_SEL, 1 },
+	},
 };
 
 static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
 	.is_legacy = false,
-	.nparams = 2,
+	.nparams = 4,
 	.param = {
+		{ RX_CHK_SYNC, 1 },
+		{ RX_SYNC_SEL, 1 },
 		{ LS_SLEW, 1 },
 		{ FS_LS_DRV, 1 },
 	},
@@ -412,7 +420,11 @@ static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
 
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs3_data = {
 	.is_legacy = false,
-	.nparams = 0,
+	.nparams = 2,
+	.param = {
+		{ RX_CHK_SYNC, 1 },
+		{ RX_SYNC_SEL, 1 },
+	},
 	.trim_func = uniphier_u3hsphy_trim_ld20,
 	.config0 = 0x92316680,
 	.config1 = 0x00000106,
-- 
2.7.4

[PATCH 5/6] phy: uniphier-usb3hs: Change Rx sync mode to avoid communication failure

[Kunihiko Hayashi]

In case of using default parameters, communication failure might occur
in rare cases. This sets Rx sync mode parameter to avoid the issue.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-usb3hs.c | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-usb3hs.c b/drivers/phy/socionext/phy-uniphier-usb3hs.c
index bdf696e..a9bc741 100644
--- a/drivers/phy/socionext/phy-uniphier-usb3hs.c
+++ b/drivers/phy/socionext/phy-uniphier-usb3hs.c
@@ -41,10 +41,12 @@
 
 #define PHY_F(regno, msb, lsb) { (regno), (msb), (lsb) }
 
+#define RX_CHK_SYNC	PHY_F(0, 5, 5)	/* RX sync mode */
+#define RX_SYNC_SEL	PHY_F(1, 1, 0)	/* RX sync length */
 #define LS_SLEW		PHY_F(10, 6, 6)	/* LS mode slew rate */
 #define FS_LS_DRV	PHY_F(10, 5, 5)	/* FS/LS slew rate */
 
-#define MAX_PHY_PARAMS	2
+#define MAX_PHY_PARAMS	4
 
 struct uniphier_u3hsphy_param {
 	struct {
@@ -395,13 +397,19 @@ static const struct uniphier_u3hsphy_soc_data uniphier_pro5_data = {
 
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs2_data = {
 	.is_legacy = false,
-	.nparams = 0,
+	.nparams = 2,
+	.param = {
+		{ RX_CHK_SYNC, 1 },
+		{ RX_SYNC_SEL, 1 },
+	},
 };
 
 static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
 	.is_legacy = false,
-	.nparams = 2,
+	.nparams = 4,
 	.param = {
+		{ RX_CHK_SYNC, 1 },
+		{ RX_SYNC_SEL, 1 },
 		{ LS_SLEW, 1 },
 		{ FS_LS_DRV, 1 },
 	},
@@ -412,7 +420,11 @@ static const struct uniphier_u3hsphy_soc_data uniphier_ld20_data = {
 
 static const struct uniphier_u3hsphy_soc_data uniphier_pxs3_data = {
 	.is_legacy = false,
-	.nparams = 0,
+	.nparams = 2,
+	.param = {
+		{ RX_CHK_SYNC, 1 },
+		{ RX_SYNC_SEL, 1 },
+	},
 	.trim_func = uniphier_u3hsphy_trim_ld20,
 	.config0 = 0x92316680,
 	.config1 = 0x00000106,
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/6] phy: uniphier-pcie: Add legacy SoC support for Pro5

[Kunihiko Hayashi]

Add legacy SoC support that needs to manage gio clock and reset and to skip
setting unimplemented phy parameters. This supports Pro5.

This specifies only 1 port use because Pro5 doesn't set it in the power-on
sequence.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-pcie.c | 83 +++++++++++++++++++++++++++----
 1 file changed, 72 insertions(+), 11 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-pcie.c b/drivers/phy/socionext/phy-uniphier-pcie.c
index 25d1d9d..cd17c70 100644
--- a/drivers/phy/socionext/phy-uniphier-pcie.c
+++ b/drivers/phy/socionext/phy-uniphier-pcie.c
@@ -19,6 +19,10 @@
 #include <linux/resource.h>
 
 /* PHY */
+#define PCL_PHY_CLKCTRL		0x0000
+#define PORT_SEL_MASK		GENMASK(11, 9)
+#define PORT_SEL_1		FIELD_PREP(PORT_SEL_MASK, 1)
+
 #define PCL_PHY_TEST_I		0x2000
 #define PCL_PHY_TEST_O		0x2004
 #define TESTI_DAT_MASK		GENMASK(13, 6)
@@ -45,13 +49,14 @@
 struct uniphier_pciephy_priv {
 	void __iomem *base;
 	struct device *dev;
-	struct clk *clk;
-	struct reset_control *rst;
+	struct clk *clk, *clk_gio;
+	struct reset_control *rst, *rst_gio;
 	const struct uniphier_pciephy_soc_data *data;
 };
 
 struct uniphier_pciephy_soc_data {
 	bool has_syscon;
+	bool is_legacy;
 };
 
 static void uniphier_pciephy_testio_write(struct uniphier_pciephy_priv *priv,
@@ -111,16 +116,35 @@ static void uniphier_pciephy_deassert(struct uniphier_pciephy_priv *priv)
 static int uniphier_pciephy_init(struct phy *phy)
 {
 	struct uniphier_pciephy_priv *priv = phy_get_drvdata(phy);
+	u32 val;
 	int ret;
 
 	ret = clk_prepare_enable(priv->clk);
 	if (ret)
 		return ret;
 
-	ret = reset_control_deassert(priv->rst);
+	ret = clk_prepare_enable(priv->clk_gio);
 	if (ret)
 		goto out_clk_disable;
 
+	ret = reset_control_deassert(priv->rst);
+	if (ret)
+		goto out_clk_gio_disable;
+
+	ret = reset_control_deassert(priv->rst_gio);
+	if (ret)
+		goto out_rst_assert;
+
+	/* support only 1 port */
+	val = readl(priv->base + PCL_PHY_CLKCTRL);
+	val &= ~PORT_SEL_MASK;
+	val |= PORT_SEL_1;
+	writel(val, priv->base + PCL_PHY_CLKCTRL);
+
+	/* legacy controller doesn't have phy_reset and parameters */
+	if (priv->data->is_legacy)
+		return 0;
+
 	uniphier_pciephy_set_param(priv, PCL_PHY_R00,
 				   RX_EQ_ADJ_EN, RX_EQ_ADJ_EN);
 	uniphier_pciephy_set_param(priv, PCL_PHY_R06, RX_EQ_ADJ,
@@ -134,6 +158,10 @@ static int uniphier_pciephy_init(struct phy *phy)
 
 	return 0;
 
+out_rst_assert:
+	reset_control_assert(priv->rst);
+out_clk_gio_disable:
+	clk_disable_unprepare(priv->clk_gio);
 out_clk_disable:
 	clk_disable_unprepare(priv->clk);
 
@@ -144,8 +172,11 @@ static int uniphier_pciephy_exit(struct phy *phy)
 {
 	struct uniphier_pciephy_priv *priv = phy_get_drvdata(phy);
 
-	uniphier_pciephy_assert(priv);
+	if (!priv->data->is_legacy)
+		uniphier_pciephy_assert(priv);
+	reset_control_assert(priv->rst_gio);
 	reset_control_assert(priv->rst);
+	clk_disable_unprepare(priv->clk_gio);
 	clk_disable_unprepare(priv->clk);
 
 	return 0;
@@ -179,13 +210,32 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-	priv->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(priv->clk))
-		return PTR_ERR(priv->clk);
-
-	priv->rst = devm_reset_control_get_shared(dev, NULL);
-	if (IS_ERR(priv->rst))
-		return PTR_ERR(priv->rst);
+	if (priv->data->is_legacy) {
+		priv->clk_gio = devm_clk_get(dev, "gio");
+		if (IS_ERR(priv->clk_gio))
+			return PTR_ERR(priv->clk_gio);
+
+		priv->rst_gio =
+			devm_reset_control_get_shared(dev, "gio");
+		if (IS_ERR(priv->rst_gio))
+			return PTR_ERR(priv->rst_gio);
+
+		priv->clk = devm_clk_get(dev, "link");
+		if (IS_ERR(priv->clk))
+			return PTR_ERR(priv->clk);
+
+		priv->rst = devm_reset_control_get_shared(dev, "link");
+		if (IS_ERR(priv->rst))
+			return PTR_ERR(priv->rst);
+	} else {
+		priv->clk = devm_clk_get(dev, NULL);
+		if (IS_ERR(priv->clk))
+			return PTR_ERR(priv->clk);
+
+		priv->rst = devm_reset_control_get_shared(dev, NULL);
+		if (IS_ERR(priv->rst))
+			return PTR_ERR(priv->rst);
+	}
 
 	phy = devm_phy_create(dev, dev->of_node, &uniphier_pciephy_ops);
 	if (IS_ERR(phy))
@@ -203,16 +253,27 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
+static const struct uniphier_pciephy_soc_data uniphier_pro5_data = {
+	.has_syscon = false,
+	.is_legacy = true,
+};
+
 static const struct uniphier_pciephy_soc_data uniphier_ld20_data = {
 	.has_syscon = true,
+	.is_legacy = false,
 };
 
 static const struct uniphier_pciephy_soc_data uniphier_pxs3_data = {
 	.has_syscon = false,
+	.is_legacy = false,
 };
 
 static const struct of_device_id uniphier_pciephy_match[] = {
 	{
+		.compatible = "socionext,uniphier-pro5-pcie-phy",
+		.data = &uniphier_pro5_data,
+	},
+	{
 		.compatible = "socionext,uniphier-ld20-pcie-phy",
 		.data = &uniphier_ld20_data,
 	},
-- 
2.7.4

[PATCH 6/6] phy: uniphier-pcie: Add legacy SoC support for Pro5

[Kunihiko Hayashi]

Add legacy SoC support that needs to manage gio clock and reset and to skip
setting unimplemented phy parameters. This supports Pro5.

This specifies only 1 port use because Pro5 doesn't set it in the power-on
sequence.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
---
 drivers/phy/socionext/phy-uniphier-pcie.c | 83 +++++++++++++++++++++++++++----
 1 file changed, 72 insertions(+), 11 deletions(-)

diff --git a/drivers/phy/socionext/phy-uniphier-pcie.c b/drivers/phy/socionext/phy-uniphier-pcie.c
index 25d1d9d..cd17c70 100644
--- a/drivers/phy/socionext/phy-uniphier-pcie.c
+++ b/drivers/phy/socionext/phy-uniphier-pcie.c
@@ -19,6 +19,10 @@
 #include <linux/resource.h>
 
 /* PHY */
+#define PCL_PHY_CLKCTRL		0x0000
+#define PORT_SEL_MASK		GENMASK(11, 9)
+#define PORT_SEL_1		FIELD_PREP(PORT_SEL_MASK, 1)
+
 #define PCL_PHY_TEST_I		0x2000
 #define PCL_PHY_TEST_O		0x2004
 #define TESTI_DAT_MASK		GENMASK(13, 6)
@@ -45,13 +49,14 @@
 struct uniphier_pciephy_priv {
 	void __iomem *base;
 	struct device *dev;
-	struct clk *clk;
-	struct reset_control *rst;
+	struct clk *clk, *clk_gio;
+	struct reset_control *rst, *rst_gio;
 	const struct uniphier_pciephy_soc_data *data;
 };
 
 struct uniphier_pciephy_soc_data {
 	bool has_syscon;
+	bool is_legacy;
 };
 
 static void uniphier_pciephy_testio_write(struct uniphier_pciephy_priv *priv,
@@ -111,16 +116,35 @@ static void uniphier_pciephy_deassert(struct uniphier_pciephy_priv *priv)
 static int uniphier_pciephy_init(struct phy *phy)
 {
 	struct uniphier_pciephy_priv *priv = phy_get_drvdata(phy);
+	u32 val;
 	int ret;
 
 	ret = clk_prepare_enable(priv->clk);
 	if (ret)
 		return ret;
 
-	ret = reset_control_deassert(priv->rst);
+	ret = clk_prepare_enable(priv->clk_gio);
 	if (ret)
 		goto out_clk_disable;
 
+	ret = reset_control_deassert(priv->rst);
+	if (ret)
+		goto out_clk_gio_disable;
+
+	ret = reset_control_deassert(priv->rst_gio);
+	if (ret)
+		goto out_rst_assert;
+
+	/* support only 1 port */
+	val = readl(priv->base + PCL_PHY_CLKCTRL);
+	val &= ~PORT_SEL_MASK;
+	val |= PORT_SEL_1;
+	writel(val, priv->base + PCL_PHY_CLKCTRL);
+
+	/* legacy controller doesn't have phy_reset and parameters */
+	if (priv->data->is_legacy)
+		return 0;
+
 	uniphier_pciephy_set_param(priv, PCL_PHY_R00,
 				   RX_EQ_ADJ_EN, RX_EQ_ADJ_EN);
 	uniphier_pciephy_set_param(priv, PCL_PHY_R06, RX_EQ_ADJ,
@@ -134,6 +158,10 @@ static int uniphier_pciephy_init(struct phy *phy)
 
 	return 0;
 
+out_rst_assert:
+	reset_control_assert(priv->rst);
+out_clk_gio_disable:
+	clk_disable_unprepare(priv->clk_gio);
 out_clk_disable:
 	clk_disable_unprepare(priv->clk);
 
@@ -144,8 +172,11 @@ static int uniphier_pciephy_exit(struct phy *phy)
 {
 	struct uniphier_pciephy_priv *priv = phy_get_drvdata(phy);
 
-	uniphier_pciephy_assert(priv);
+	if (!priv->data->is_legacy)
+		uniphier_pciephy_assert(priv);
+	reset_control_assert(priv->rst_gio);
 	reset_control_assert(priv->rst);
+	clk_disable_unprepare(priv->clk_gio);
 	clk_disable_unprepare(priv->clk);
 
 	return 0;
@@ -179,13 +210,32 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->base))
 		return PTR_ERR(priv->base);
 
-	priv->clk = devm_clk_get(dev, NULL);
-	if (IS_ERR(priv->clk))
-		return PTR_ERR(priv->clk);
-
-	priv->rst = devm_reset_control_get_shared(dev, NULL);
-	if (IS_ERR(priv->rst))
-		return PTR_ERR(priv->rst);
+	if (priv->data->is_legacy) {
+		priv->clk_gio = devm_clk_get(dev, "gio");
+		if (IS_ERR(priv->clk_gio))
+			return PTR_ERR(priv->clk_gio);
+
+		priv->rst_gio =
+			devm_reset_control_get_shared(dev, "gio");
+		if (IS_ERR(priv->rst_gio))
+			return PTR_ERR(priv->rst_gio);
+
+		priv->clk = devm_clk_get(dev, "link");
+		if (IS_ERR(priv->clk))
+			return PTR_ERR(priv->clk);
+
+		priv->rst = devm_reset_control_get_shared(dev, "link");
+		if (IS_ERR(priv->rst))
+			return PTR_ERR(priv->rst);
+	} else {
+		priv->clk = devm_clk_get(dev, NULL);
+		if (IS_ERR(priv->clk))
+			return PTR_ERR(priv->clk);
+
+		priv->rst = devm_reset_control_get_shared(dev, NULL);
+		if (IS_ERR(priv->rst))
+			return PTR_ERR(priv->rst);
+	}
 
 	phy = devm_phy_create(dev, dev->of_node, &uniphier_pciephy_ops);
 	if (IS_ERR(phy))
@@ -203,16 +253,27 @@ static int uniphier_pciephy_probe(struct platform_device *pdev)
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
+static const struct uniphier_pciephy_soc_data uniphier_pro5_data = {
+	.has_syscon = false,
+	.is_legacy = true,
+};
+
 static const struct uniphier_pciephy_soc_data uniphier_ld20_data = {
 	.has_syscon = true,
+	.is_legacy = false,
 };
 
 static const struct uniphier_pciephy_soc_data uniphier_pxs3_data = {
 	.has_syscon = false,
+	.is_legacy = false,
 };
 
 static const struct of_device_id uniphier_pciephy_match[] = {
 	{
+		.compatible = "socionext,uniphier-pro5-pcie-phy",
+		.data = &uniphier_pro5_data,
+	},
+	{
 		.compatible = "socionext,uniphier-ld20-pcie-phy",
 		.data = &uniphier_ld20_data,
 	},
-- 
2.7.4


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/6] dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from usb3-hsphy

[Rob Herring]

On Wed,  6 Nov 2019 19:26:15 +0900, Kunihiko Hayashi wrote:
> This adds compatible string for Pro5 SoC that needs to manage gio clock
> and reset. And Pro4 SoC uses USB2 PHY instead of USB3 HS-PHY, so this
> removes Pro4 description from usb3-hsphy.
> 
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> ---
>  Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt | 13 +++++++++----
>  .../devicetree/bindings/phy/uniphier-usb3-hsphy.txt         |  6 +++---
>  .../devicetree/bindings/phy/uniphier-usb3-ssphy.txt         |  5 +++--
>  3 files changed, 15 insertions(+), 9 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH 2/6] dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from usb3-hsphy

[Rob Herring]

On Wed,  6 Nov 2019 19:26:15 +0900, Kunihiko Hayashi wrote:
> This adds compatible string for Pro5 SoC that needs to manage gio clock
> and reset. And Pro4 SoC uses USB2 PHY instead of USB3 HS-PHY, so this
> removes Pro4 description from usb3-hsphy.
> 
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> ---
>  Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt | 13 +++++++++----
>  .../devicetree/bindings/phy/uniphier-usb3-hsphy.txt         |  6 +++---
>  .../devicetree/bindings/phy/uniphier-usb3-ssphy.txt         |  5 +++--
>  3 files changed, 15 insertions(+), 9 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[Kunihiko Hayashi]

Hi,

Gentle ping.
Are there any comments about this series?

Thank you,

On Wed, 6 Nov 2019 19:26:13 +0900 <hayashi.kunihiko@socionext.com> wrote:

> This series adds some improvements to PHY interface drivers, and adds legacy SoC
> support that needs to manage gio clock and reset.
> 
> Kunihiko Hayashi (6):
>   phy: socionext: Use devm_platform_ioremap_resource()
>   dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from
>     usb3-hsphy
>   phy: uniphier-usb3ss: Add Pro5 support
>   phy: uniphier-usb3hs: Add legacy SoC support for Pro5
>   phy: uniphier-usb3hs: Change Rx sync mode to avoid communication
>     failure
>   phy: uniphier-pcie: Add legacy SoC support for Pro5
> 
>  .../devicetree/bindings/phy/uniphier-pcie-phy.txt  | 13 ++-
>  .../bindings/phy/uniphier-usb3-hsphy.txt           |  6 +-
>  .../bindings/phy/uniphier-usb3-ssphy.txt           |  5 +-
>  drivers/phy/socionext/phy-uniphier-pcie.c          | 87 ++++++++++++++++----
>  drivers/phy/socionext/phy-uniphier-usb3hs.c        | 92 ++++++++++++++++------
>  drivers/phy/socionext/phy-uniphier-usb3ss.c        |  8 +-
>  6 files changed, 163 insertions(+), 48 deletions(-)
> 
> -- 
> 2.7.4

---
Best Regards,
Kunihiko Hayashi

Re: [PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[Kunihiko Hayashi]

Hi,

Gentle ping.
Are there any comments about this series?

Thank you,

On Wed, 6 Nov 2019 19:26:13 +0900 <hayashi.kunihiko@socionext.com> wrote:

> This series adds some improvements to PHY interface drivers, and adds legacy SoC
> support that needs to manage gio clock and reset.
> 
> Kunihiko Hayashi (6):
>   phy: socionext: Use devm_platform_ioremap_resource()
>   dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from
>     usb3-hsphy
>   phy: uniphier-usb3ss: Add Pro5 support
>   phy: uniphier-usb3hs: Add legacy SoC support for Pro5
>   phy: uniphier-usb3hs: Change Rx sync mode to avoid communication
>     failure
>   phy: uniphier-pcie: Add legacy SoC support for Pro5
> 
>  .../devicetree/bindings/phy/uniphier-pcie-phy.txt  | 13 ++-
>  .../bindings/phy/uniphier-usb3-hsphy.txt           |  6 +-
>  .../bindings/phy/uniphier-usb3-ssphy.txt           |  5 +-
>  drivers/phy/socionext/phy-uniphier-pcie.c          | 87 ++++++++++++++++----
>  drivers/phy/socionext/phy-uniphier-usb3hs.c        | 92 ++++++++++++++++------
>  drivers/phy/socionext/phy-uniphier-usb3ss.c        |  8 +-
>  6 files changed, 163 insertions(+), 48 deletions(-)
> 
> -- 
> 2.7.4

---
Best Regards,
Kunihiko Hayashi


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[Kunihiko Hayashi]

Hi,

Gentle ping.
Is there any comments about this series?

Thank you,

On Wed, 6 Nov 2019 19:26:13 +0900 <hayashi.kunihiko@socionext.com> wrote:

> This series adds some improvements to PHY interface drivers, and adds legacy SoC
> support that needs to manage gio clock and reset.
> 
> Kunihiko Hayashi (6):
>   phy: socionext: Use devm_platform_ioremap_resource()
>   dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from
>     usb3-hsphy
>   phy: uniphier-usb3ss: Add Pro5 support
>   phy: uniphier-usb3hs: Add legacy SoC support for Pro5
>   phy: uniphier-usb3hs: Change Rx sync mode to avoid communication
>     failure
>   phy: uniphier-pcie: Add legacy SoC support for Pro5
> 
>  .../devicetree/bindings/phy/uniphier-pcie-phy.txt  | 13 ++-
>  .../bindings/phy/uniphier-usb3-hsphy.txt           |  6 +-
>  .../bindings/phy/uniphier-usb3-ssphy.txt           |  5 +-
>  drivers/phy/socionext/phy-uniphier-pcie.c          | 87 ++++++++++++++++----
>  drivers/phy/socionext/phy-uniphier-usb3hs.c        | 92 ++++++++++++++++------
>  drivers/phy/socionext/phy-uniphier-usb3ss.c        |  8 +-
>  6 files changed, 163 insertions(+), 48 deletions(-)
> 
> -- 
> 2.7.4

---
Best Regards,
Kunihiko Hayashi

Re: [PATCH 0/6] phy: socionext: Add some improvements and legacy SoC support

[Kunihiko Hayashi]

Hi,

Gentle ping.
Is there any comments about this series?

Thank you,

On Wed, 6 Nov 2019 19:26:13 +0900 <hayashi.kunihiko@socionext.com> wrote:

> This series adds some improvements to PHY interface drivers, and adds legacy SoC
> support that needs to manage gio clock and reset.
> 
> Kunihiko Hayashi (6):
>   phy: socionext: Use devm_platform_ioremap_resource()
>   dt-bindings: phy: socionext: Add Pro5 support and remove Pro4 from
>     usb3-hsphy
>   phy: uniphier-usb3ss: Add Pro5 support
>   phy: uniphier-usb3hs: Add legacy SoC support for Pro5
>   phy: uniphier-usb3hs: Change Rx sync mode to avoid communication
>     failure
>   phy: uniphier-pcie: Add legacy SoC support for Pro5
> 
>  .../devicetree/bindings/phy/uniphier-pcie-phy.txt  | 13 ++-
>  .../bindings/phy/uniphier-usb3-hsphy.txt           |  6 +-
>  .../bindings/phy/uniphier-usb3-ssphy.txt           |  5 +-
>  drivers/phy/socionext/phy-uniphier-pcie.c          | 87 ++++++++++++++++----
>  drivers/phy/socionext/phy-uniphier-usb3hs.c        | 92 ++++++++++++++++------
>  drivers/phy/socionext/phy-uniphier-usb3ss.c        |  8 +-
>  6 files changed, 163 insertions(+), 48 deletions(-)
> 
> -- 
> 2.7.4

---
Best Regards,
Kunihiko Hayashi


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel