All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm
@ 2019-12-17 12:37 Veerabhadrarao Badiganti
  2019-12-20 13:59 ` Adrian Hunter
  0 siblings, 1 reply; 6+ messages in thread
From: Veerabhadrarao Badiganti @ 2019-12-17 12:37 UTC (permalink / raw)
  To: adrian.hunter, ulf.hansson, agross
  Cc: asutoshd, stummala, sayalil, cang, rampraka, linux-mmc,
	linux-kernel, linux-arm-msm, Ritesh Harjani,
	Veerabhadrarao Badiganti

From: Ritesh Harjani <riteshh@codeaurora.org>

This adds CQHCI support for sdhci-msm platforms.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>

---
This patch is based on RFC patch
https://lkml.org/lkml/2017/8/30/313

Changes since RFC:
	- Updated settings so that TDLBA won't get reset when
	  CQE is enabled.
	- Removed new compatible string and moved to supports-cqe
	  dt flag to identify CQE support.
	- Incorporated review comments.

Tested on: qcs404, sc7180
---
 drivers/mmc/host/sdhci-msm.c | 115 ++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 114 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 3d0bb5e..a4e3507 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -15,6 +15,7 @@
 #include <linux/regulator/consumer.h>
 
 #include "sdhci-pltfm.h"
+#include "cqhci.h"
 
 #define CORE_MCI_VERSION		0x50
 #define CORE_VERSION_MAJOR_SHIFT	28
@@ -122,6 +123,10 @@
 #define msm_host_writel(msm_host, val, host, offset) \
 	msm_host->var_ops->msm_writel_relaxed(val, host, offset)
 
+/* CQHCI vendor specific registers */
+#define CQHCI_VENDOR_CFG1	0xA00
+#define DISABLE_RST_ON_CMDQ_EN	(0x3 << 13)
+
 struct sdhci_msm_offset {
 	u32 core_hc_mode;
 	u32 core_mci_data_cnt;
@@ -1567,6 +1572,109 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
 	__sdhci_msm_set_clock(host, clock);
 }
 
+/*****************************************************************************\
+ *                                                                           *
+ * MSM Command Queue Engine (CQE)                                            *
+ *                                                                           *
+\*****************************************************************************/
+
+static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
+{
+	int cmd_error = 0;
+	int data_error = 0;
+
+	if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
+		return intmask;
+
+	cqhci_irq(host->mmc, intmask, cmd_error, data_error);
+	return 0;
+}
+
+void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
+{
+	struct sdhci_host *host = mmc_priv(mmc);
+	unsigned long flags;
+	u32 ctrl;
+
+	/*
+	 * When CQE is halted, the legacy SDHCI path operates only
+	 * on 128bit descriptors in 64bit mode.
+	 */
+	if (host->flags & SDHCI_USE_64_BIT_DMA)
+		host->desc_sz = 16;
+
+	spin_lock_irqsave(&host->lock, flags);
+
+	/*
+	 * During CQE operation command complete bit gets latched.
+	 * So s/w should clear command complete interrupt status when CQE is
+	 * halted. Otherwise unexpected SDCHI legacy interrupt gets
+	 * triggered when CQE is halted.
+	 */
+	ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
+	ctrl |= SDHCI_INT_RESPONSE;
+	sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
+	sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
+
+	spin_unlock_irqrestore(&host->lock, flags);
+
+	sdhci_cqe_disable(mmc, recovery);
+}
+
+static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
+	.enable		= sdhci_cqe_enable,
+	.disable	= sdhci_msm_cqe_disable,
+};
+
+static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
+				struct platform_device *pdev)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+	struct cqhci_host *cq_host;
+	bool dma64;
+	int ret;
+
+	ret = sdhci_setup_host(host);
+	if (ret)
+		return ret;
+
+	cq_host = cqhci_pltfm_init(pdev);
+	if (IS_ERR(cq_host)) {
+		ret = PTR_ERR(cq_host);
+		dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
+		goto cleanup;
+	}
+
+	msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
+	cq_host->ops = &sdhci_msm_cqhci_ops;
+
+	dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
+
+	ret = cqhci_init(cq_host, host->mmc, dma64);
+	if (ret) {
+		dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
+				mmc_hostname(host->mmc), ret);
+		goto cleanup;
+	}
+
+	/* Disable cqe reset due to cqe enable signal */
+	cqhci_writel(cq_host, cqhci_readl(cq_host, CQHCI_VENDOR_CFG1) |
+		       DISABLE_RST_ON_CMDQ_EN, CQHCI_VENDOR_CFG1);
+
+	ret = __sdhci_add_host(host);
+	if (ret)
+		goto cleanup;
+
+	dev_info(&pdev->dev, "%s: CQE init: success\n",
+			mmc_hostname(host->mmc));
+	return ret;
+
+cleanup:
+	sdhci_cleanup_host(host);
+	return ret;
+}
+
 /*
  * Platform specific register write functions. This is so that, if any
  * register write needs to be followed up by platform specific actions,
@@ -1731,6 +1839,7 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
 	.set_uhs_signaling = sdhci_msm_set_uhs_signaling,
 	.write_w = sdhci_msm_writew,
 	.write_b = sdhci_msm_writeb,
+	.irq	= sdhci_msm_cqe_irq,
 };
 
 static const struct sdhci_pltfm_data sdhci_msm_pdata = {
@@ -1754,6 +1863,7 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 	u8 core_major;
 	const struct sdhci_msm_offset *msm_offset;
 	const struct sdhci_msm_variant_info *var_info;
+	struct device_node *node = pdev->dev.of_node;
 
 	host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
 	if (IS_ERR(host))
@@ -1952,7 +2062,10 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 	pm_runtime_use_autosuspend(&pdev->dev);
 
 	host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
-	ret = sdhci_add_host(host);
+	if (of_property_read_bool(node, "supports-cqe"))
+		ret = sdhci_msm_cqe_add_host(host, pdev);
+	else
+		ret = sdhci_add_host(host);
 	if (ret)
 		goto pm_runtime_disable;
 	sdhci_msm_set_regulator_caps(msm_host);
-- 
Qualcomm India Private Limited, on behalf of Qualcomm Innovation Center, Inc., is a member of Code Aurora Forum, a Linux Foundation Collaborative Project

^ permalink raw reply related	[flat|nested] 6+ messages in thread

* Re: [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm
  2019-12-17 12:37 [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm Veerabhadrarao Badiganti
@ 2019-12-20 13:59 ` Adrian Hunter
  2020-01-02 11:30   ` Veerabhadrarao Badiganti
  0 siblings, 1 reply; 6+ messages in thread
From: Adrian Hunter @ 2019-12-20 13:59 UTC (permalink / raw)
  To: Veerabhadrarao Badiganti, ulf.hansson, agross
  Cc: asutoshd, stummala, sayalil, cang, rampraka, linux-mmc,
	linux-kernel, linux-arm-msm, Ritesh Harjani

On 17/12/19 2:37 pm, Veerabhadrarao Badiganti wrote:
> From: Ritesh Harjani <riteshh@codeaurora.org>
> 
> This adds CQHCI support for sdhci-msm platforms.
> 
> Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
> 
> ---
> This patch is based on RFC patch
> https://lkml.org/lkml/2017/8/30/313
> 
> Changes since RFC:
> 	- Updated settings so that TDLBA won't get reset when
> 	  CQE is enabled.
> 	- Removed new compatible string and moved to supports-cqe
> 	  dt flag to identify CQE support.
> 	- Incorporated review comments.
> 
> Tested on: qcs404, sc7180
> ---
>  drivers/mmc/host/sdhci-msm.c | 115 ++++++++++++++++++++++++++++++++++++++++++-
>  1 file changed, 114 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> index 3d0bb5e..a4e3507 100644
> --- a/drivers/mmc/host/sdhci-msm.c
> +++ b/drivers/mmc/host/sdhci-msm.c
> @@ -15,6 +15,7 @@
>  #include <linux/regulator/consumer.h>
>  
>  #include "sdhci-pltfm.h"
> +#include "cqhci.h"
>  
>  #define CORE_MCI_VERSION		0x50
>  #define CORE_VERSION_MAJOR_SHIFT	28
> @@ -122,6 +123,10 @@
>  #define msm_host_writel(msm_host, val, host, offset) \
>  	msm_host->var_ops->msm_writel_relaxed(val, host, offset)
>  
> +/* CQHCI vendor specific registers */
> +#define CQHCI_VENDOR_CFG1	0xA00
> +#define DISABLE_RST_ON_CMDQ_EN	(0x3 << 13)
> +
>  struct sdhci_msm_offset {
>  	u32 core_hc_mode;
>  	u32 core_mci_data_cnt;
> @@ -1567,6 +1572,109 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
>  	__sdhci_msm_set_clock(host, clock);
>  }
>  
> +/*****************************************************************************\
> + *                                                                           *
> + * MSM Command Queue Engine (CQE)                                            *
> + *                                                                           *
> +\*****************************************************************************/
> +
> +static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
> +{
> +	int cmd_error = 0;
> +	int data_error = 0;
> +
> +	if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
> +		return intmask;
> +
> +	cqhci_irq(host->mmc, intmask, cmd_error, data_error);
> +	return 0;
> +}
> +
> +void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
> +{
> +	struct sdhci_host *host = mmc_priv(mmc);
> +	unsigned long flags;
> +	u32 ctrl;
> +
> +	/*
> +	 * When CQE is halted, the legacy SDHCI path operates only
> +	 * on 128bit descriptors in 64bit mode.
> +	 */
> +	if (host->flags & SDHCI_USE_64_BIT_DMA)
> +		host->desc_sz = 16;

The adma_table_sz depends on desc_sz, so it cannot be changed here.
If you do something like below, then you can set desc_sz before calling
sdhci_setup_host()

diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index f4540f9892ce..f1d3b70ff769 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -3825,9 +3825,10 @@ int sdhci_setup_host(struct sdhci_host *host)
 		void *buf;
 
 		if (host->flags & SDHCI_USE_64_BIT_DMA) {
+			if (!host->desc_sz)
+				host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
 			host->adma_table_sz = host->adma_table_cnt *
-					      SDHCI_ADMA2_64_DESC_SZ(host);
-			host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
+					      host->desc_sz;
 		} else {
 			host->adma_table_sz = host->adma_table_cnt *
 					      SDHCI_ADMA2_32_DESC_SZ;


> +
> +	spin_lock_irqsave(&host->lock, flags);
> +
> +	/*
> +	 * During CQE operation command complete bit gets latched.
> +	 * So s/w should clear command complete interrupt status when CQE is
> +	 * halted. Otherwise unexpected SDCHI legacy interrupt gets
> +	 * triggered when CQE is halted.
> +	 */
> +	ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
> +	ctrl |= SDHCI_INT_RESPONSE;
> +	sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
> +	sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
> +
> +	spin_unlock_irqrestore(&host->lock, flags);
> +
> +	sdhci_cqe_disable(mmc, recovery);
> +}
> +
> +static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
> +	.enable		= sdhci_cqe_enable,
> +	.disable	= sdhci_msm_cqe_disable,
> +};
> +
> +static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
> +				struct platform_device *pdev)
> +{
> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> +	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
> +	struct cqhci_host *cq_host;
> +	bool dma64;
> +	int ret;
> +
> +	ret = sdhci_setup_host(host);
> +	if (ret)
> +		return ret;
> +
> +	cq_host = cqhci_pltfm_init(pdev);
> +	if (IS_ERR(cq_host)) {
> +		ret = PTR_ERR(cq_host);
> +		dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
> +		goto cleanup;
> +	}
> +
> +	msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
> +	cq_host->ops = &sdhci_msm_cqhci_ops;
> +
> +	dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
> +
> +	ret = cqhci_init(cq_host, host->mmc, dma64);
> +	if (ret) {
> +		dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
> +				mmc_hostname(host->mmc), ret);
> +		goto cleanup;
> +	}
> +
> +	/* Disable cqe reset due to cqe enable signal */
> +	cqhci_writel(cq_host, cqhci_readl(cq_host, CQHCI_VENDOR_CFG1) |
> +		       DISABLE_RST_ON_CMDQ_EN, CQHCI_VENDOR_CFG1);
> +
> +	ret = __sdhci_add_host(host);
> +	if (ret)
> +		goto cleanup;
> +
> +	dev_info(&pdev->dev, "%s: CQE init: success\n",
> +			mmc_hostname(host->mmc));
> +	return ret;
> +
> +cleanup:
> +	sdhci_cleanup_host(host);
> +	return ret;
> +}
> +
>  /*
>   * Platform specific register write functions. This is so that, if any
>   * register write needs to be followed up by platform specific actions,
> @@ -1731,6 +1839,7 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
>  	.set_uhs_signaling = sdhci_msm_set_uhs_signaling,
>  	.write_w = sdhci_msm_writew,
>  	.write_b = sdhci_msm_writeb,
> +	.irq	= sdhci_msm_cqe_irq,
>  };
>  
>  static const struct sdhci_pltfm_data sdhci_msm_pdata = {
> @@ -1754,6 +1863,7 @@ static int sdhci_msm_probe(struct platform_device *pdev)
>  	u8 core_major;
>  	const struct sdhci_msm_offset *msm_offset;
>  	const struct sdhci_msm_variant_info *var_info;
> +	struct device_node *node = pdev->dev.of_node;
>  
>  	host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
>  	if (IS_ERR(host))
> @@ -1952,7 +2062,10 @@ static int sdhci_msm_probe(struct platform_device *pdev)
>  	pm_runtime_use_autosuspend(&pdev->dev);
>  
>  	host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
> -	ret = sdhci_add_host(host);
> +	if (of_property_read_bool(node, "supports-cqe"))
> +		ret = sdhci_msm_cqe_add_host(host, pdev);
> +	else
> +		ret = sdhci_add_host(host);
>  	if (ret)
>  		goto pm_runtime_disable;
>  	sdhci_msm_set_regulator_caps(msm_host);
> 


^ permalink raw reply related	[flat|nested] 6+ messages in thread

* Re: [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm
  2019-12-20 13:59 ` Adrian Hunter
@ 2020-01-02 11:30   ` Veerabhadrarao Badiganti
  2020-01-10  8:56     ` Veerabhadrarao Badiganti
  0 siblings, 1 reply; 6+ messages in thread
From: Veerabhadrarao Badiganti @ 2020-01-02 11:30 UTC (permalink / raw)
  To: Adrian Hunter, ulf.hansson, agross
  Cc: asutoshd, stummala, sayalil, cang, rampraka, linux-mmc,
	linux-kernel, linux-arm-msm, Ritesh Harjani


On 12/20/2019 7:29 PM, Adrian Hunter wrote:
> On 17/12/19 2:37 pm, Veerabhadrarao Badiganti wrote:
>> From: Ritesh Harjani<riteshh@codeaurora.org>
>>
>> This adds CQHCI support for sdhci-msm platforms.
>>
>> Signed-off-by: Ritesh Harjani<riteshh@codeaurora.org>
>> Signed-off-by: Veerabhadrarao Badiganti<vbadigan@codeaurora.org>
>>
>> ---
>> This patch is based on RFC patch
>> https://lkml.org/lkml/2017/8/30/313
>>
>> Changes since RFC:
>> 	- Updated settings so that TDLBA won't get reset when
>> 	  CQE is enabled.
>> 	- Removed new compatible string and moved to supports-cqe
>> 	  dt flag to identify CQE support.
>> 	- Incorporated review comments.
>>
>> Tested on: qcs404, sc7180
>> ---
>>   drivers/mmc/host/sdhci-msm.c | 115 ++++++++++++++++++++++++++++++++++++++++++-
>>   1 file changed, 114 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
>> index 3d0bb5e..a4e3507 100644
>> --- a/drivers/mmc/host/sdhci-msm.c
>> +++ b/drivers/mmc/host/sdhci-msm.c
>> @@ -15,6 +15,7 @@
>>   #include <linux/regulator/consumer.h>
>>   
>>   #include "sdhci-pltfm.h"
>> +#include "cqhci.h"
>>   
>>   #define CORE_MCI_VERSION		0x50
>>   #define CORE_VERSION_MAJOR_SHIFT	28
>> @@ -122,6 +123,10 @@
>>   #define msm_host_writel(msm_host, val, host, offset) \
>>   	msm_host->var_ops->msm_writel_relaxed(val, host, offset)
>>   
>> +/* CQHCI vendor specific registers */
>> +#define CQHCI_VENDOR_CFG1	0xA00
>> +#define DISABLE_RST_ON_CMDQ_EN	(0x3 << 13)
>> +
>>   struct sdhci_msm_offset {
>>   	u32 core_hc_mode;
>>   	u32 core_mci_data_cnt;
>> @@ -1567,6 +1572,109 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
>>   	__sdhci_msm_set_clock(host, clock);
>>   }
>>   
>> +/*****************************************************************************\
>> + *                                                                           *
>> + * MSM Command Queue Engine (CQE)                                            *
>> + *                                                                           *
>> +\*****************************************************************************/
>> +
>> +static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
>> +{
>> +	int cmd_error = 0;
>> +	int data_error = 0;
>> +
>> +	if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
>> +		return intmask;
>> +
>> +	cqhci_irq(host->mmc, intmask, cmd_error, data_error);
>> +	return 0;
>> +}
>> +
>> +void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
>> +{
>> +	struct sdhci_host *host = mmc_priv(mmc);
>> +	unsigned long flags;
>> +	u32 ctrl;
>> +
>> +	/*
>> +	 * When CQE is halted, the legacy SDHCI path operates only
>> +	 * on 128bit descriptors in 64bit mode.
>> +	 */
>> +	if (host->flags & SDHCI_USE_64_BIT_DMA)
>> +		host->desc_sz = 16;
> The adma_table_sz depends on desc_sz, so it cannot be changed here.
> If you do something like below, then you can set desc_sz before calling
> sdhci_setup_host()
>
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index f4540f9892ce..f1d3b70ff769 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -3825,9 +3825,10 @@ int sdhci_setup_host(struct sdhci_host *host)
>   		void *buf;
>   
>   		if (host->flags & SDHCI_USE_64_BIT_DMA) {
> +			if (!host->desc_sz)
> +				host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>   			host->adma_table_sz = host->adma_table_cnt *
> -					      SDHCI_ADMA2_64_DESC_SZ(host);
> -			host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
> +					      host->desc_sz;
>   		} else {
>   			host->adma_table_sz = host->adma_table_cnt *
>   					      SDHCI_ADMA2_32_DESC_SZ;

Thanks Adrian for the suggestion. I will add this change.

But even with this change, still i will have to override 'host->desc_sz' 
variable since qcom sdhci controller expects/operates-on

12-byte descriptor as long was CQE is not enabled. When CQE is enabled, 
it operates only on 16-bype descriptors (even when CQE is halted).

If i fix "host->desc_sz" to 16 then all the data transfer commands 
during card initialization (till CQE is enabled) would fail.

I may have to update as below:

     host->desc_sz = 16;

     sdhci_add_host()  ;

    host->desc_sz = 12;

And then cqhci_host_ops->enable() -> host->desc_sz = 16;

Please let me know if this is fine or if you have any other suggestion 
to support this limitation of qcom controller w.r.t ADMA descriptors 
with CQE.

>> +
>> +	spin_lock_irqsave(&host->lock, flags);
>> +
>> +	/*
>> +	 * During CQE operation command complete bit gets latched.
>> +	 * So s/w should clear command complete interrupt status when CQE is
>> +	 * halted. Otherwise unexpected SDCHI legacy interrupt gets
>> +	 * triggered when CQE is halted.
>> +	 */
>> +	ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
>> +	ctrl |= SDHCI_INT_RESPONSE;
>> +	sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
>> +	sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
>> +
>> +	spin_unlock_irqrestore(&host->lock, flags);
>> +
>> +	sdhci_cqe_disable(mmc, recovery);
>> +}
>> +
>> +static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
>> +	.enable		= sdhci_cqe_enable,
>> +	.disable	= sdhci_msm_cqe_disable,
>> +};
>> +
>> +static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
>> +				struct platform_device *pdev)
>> +{
>> +	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>> +	struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
>> +	struct cqhci_host *cq_host;
>> +	bool dma64;
>> +	int ret;
>> +
>> +	ret = sdhci_setup_host(host);
>> +	if (ret)
>> +		return ret;
>> +
>> +	cq_host = cqhci_pltfm_init(pdev);
>> +	if (IS_ERR(cq_host)) {
>> +		ret = PTR_ERR(cq_host);
>> +		dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
>> +		goto cleanup;
>> +	}
>> +
>> +	msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
>> +	cq_host->ops = &sdhci_msm_cqhci_ops;
>> +
>> +	dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
>> +
>> +	ret = cqhci_init(cq_host, host->mmc, dma64);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
>> +				mmc_hostname(host->mmc), ret);
>> +		goto cleanup;
>> +	}
>> +
>> +	/* Disable cqe reset due to cqe enable signal */
>> +	cqhci_writel(cq_host, cqhci_readl(cq_host, CQHCI_VENDOR_CFG1) |
>> +		       DISABLE_RST_ON_CMDQ_EN, CQHCI_VENDOR_CFG1);
>> +
>> +	ret = __sdhci_add_host(host);
>> +	if (ret)
>> +		goto cleanup;
>> +
>> +	dev_info(&pdev->dev, "%s: CQE init: success\n",
>> +			mmc_hostname(host->mmc));
>> +	return ret;
>> +
>> +cleanup:
>> +	sdhci_cleanup_host(host);
>> +	return ret;
>> +}
>> +
>>   /*
>>    * Platform specific register write functions. This is so that, if any
>>    * register write needs to be followed up by platform specific actions,
>> @@ -1731,6 +1839,7 @@ static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
>>   	.set_uhs_signaling = sdhci_msm_set_uhs_signaling,
>>   	.write_w = sdhci_msm_writew,
>>   	.write_b = sdhci_msm_writeb,
>> +	.irq	= sdhci_msm_cqe_irq,
>>   };
>>   
>>   static const struct sdhci_pltfm_data sdhci_msm_pdata = {
>> @@ -1754,6 +1863,7 @@ static int sdhci_msm_probe(struct platform_device *pdev)
>>   	u8 core_major;
>>   	const struct sdhci_msm_offset *msm_offset;
>>   	const struct sdhci_msm_variant_info *var_info;
>> +	struct device_node *node = pdev->dev.of_node;
>>   
>>   	host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
>>   	if (IS_ERR(host))
>> @@ -1952,7 +2062,10 @@ static int sdhci_msm_probe(struct platform_device *pdev)
>>   	pm_runtime_use_autosuspend(&pdev->dev);
>>   
>>   	host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
>> -	ret = sdhci_add_host(host);
>> +	if (of_property_read_bool(node, "supports-cqe"))
>> +		ret = sdhci_msm_cqe_add_host(host, pdev);
>> +	else
>> +		ret = sdhci_add_host(host);
>>   	if (ret)
>>   		goto pm_runtime_disable;
>>   	sdhci_msm_set_regulator_caps(msm_host);
>>

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm
  2020-01-02 11:30   ` Veerabhadrarao Badiganti
@ 2020-01-10  8:56     ` Veerabhadrarao Badiganti
  2020-01-13  7:24       ` Adrian Hunter
  0 siblings, 1 reply; 6+ messages in thread
From: Veerabhadrarao Badiganti @ 2020-01-10  8:56 UTC (permalink / raw)
  To: Adrian Hunter, ulf.hansson, agross
  Cc: asutoshd, stummala, sayalil, cang, rampraka, linux-mmc,
	linux-kernel, linux-arm-msm, Ritesh Harjani


On 1/2/2020 5:00 PM, Veerabhadrarao Badiganti wrote:
>
> On 12/20/2019 7:29 PM, Adrian Hunter wrote:
>> On 17/12/19 2:37 pm, Veerabhadrarao Badiganti wrote:
>>> From: Ritesh Harjani<riteshh@codeaurora.org>
>>>
>>> This adds CQHCI support for sdhci-msm platforms.
>>>
>>> Signed-off-by: Ritesh Harjani<riteshh@codeaurora.org>
>>> Signed-off-by: Veerabhadrarao Badiganti<vbadigan@codeaurora.org>
>>>
>>> ---
>>> This patch is based on RFC patch
>>> https://lkml.org/lkml/2017/8/30/313
>>>
>>> Changes since RFC:
>>>     - Updated settings so that TDLBA won't get reset when
>>>       CQE is enabled.
>>>     - Removed new compatible string and moved to supports-cqe
>>>       dt flag to identify CQE support.
>>>     - Incorporated review comments.
>>>
>>> Tested on: qcs404, sc7180
>>> ---
>>>   drivers/mmc/host/sdhci-msm.c | 115 
>>> ++++++++++++++++++++++++++++++++++++++++++-
>>>   1 file changed, 114 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/mmc/host/sdhci-msm.c 
>>> b/drivers/mmc/host/sdhci-msm.c
>>> index 3d0bb5e..a4e3507 100644
>>> --- a/drivers/mmc/host/sdhci-msm.c
>>> +++ b/drivers/mmc/host/sdhci-msm.c
>>> @@ -15,6 +15,7 @@
>>>   #include <linux/regulator/consumer.h>
>>>     #include "sdhci-pltfm.h"
>>> +#include "cqhci.h"
>>>     #define CORE_MCI_VERSION        0x50
>>>   #define CORE_VERSION_MAJOR_SHIFT    28
>>> @@ -122,6 +123,10 @@
>>>   #define msm_host_writel(msm_host, val, host, offset) \
>>>       msm_host->var_ops->msm_writel_relaxed(val, host, offset)
>>>   +/* CQHCI vendor specific registers */
>>> +#define CQHCI_VENDOR_CFG1    0xA00
>>> +#define DISABLE_RST_ON_CMDQ_EN    (0x3 << 13)
>>> +
>>>   struct sdhci_msm_offset {
>>>       u32 core_hc_mode;
>>>       u32 core_mci_data_cnt;
>>> @@ -1567,6 +1572,109 @@ static void sdhci_msm_set_clock(struct 
>>> sdhci_host *host, unsigned int clock)
>>>       __sdhci_msm_set_clock(host, clock);
>>>   }
>>> +/*****************************************************************************\
>>> + * *
>>> + * MSM Command Queue Engine 
>>> (CQE)                                            *
>>> + * *
>>> +\*****************************************************************************/ 
>>>
>>> +
>>> +static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
>>> +{
>>> +    int cmd_error = 0;
>>> +    int data_error = 0;
>>> +
>>> +    if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
>>> +        return intmask;
>>> +
>>> +    cqhci_irq(host->mmc, intmask, cmd_error, data_error);
>>> +    return 0;
>>> +}
>>> +
>>> +void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
>>> +{
>>> +    struct sdhci_host *host = mmc_priv(mmc);
>>> +    unsigned long flags;
>>> +    u32 ctrl;
>>> +
>>> +    /*
>>> +     * When CQE is halted, the legacy SDHCI path operates only
>>> +     * on 128bit descriptors in 64bit mode.
>>> +     */
>>> +    if (host->flags & SDHCI_USE_64_BIT_DMA)
>>> +        host->desc_sz = 16;
>> The adma_table_sz depends on desc_sz, so it cannot be changed here.
>> If you do something like below, then you can set desc_sz before calling
>> sdhci_setup_host()
>>
>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>> index f4540f9892ce..f1d3b70ff769 100644
>> --- a/drivers/mmc/host/sdhci.c
>> +++ b/drivers/mmc/host/sdhci.c
>> @@ -3825,9 +3825,10 @@ int sdhci_setup_host(struct sdhci_host *host)
>>           void *buf;
>>             if (host->flags & SDHCI_USE_64_BIT_DMA) {
>> +            if (!host->desc_sz)
>> +                host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>>               host->adma_table_sz = host->adma_table_cnt *
>> -                          SDHCI_ADMA2_64_DESC_SZ(host);
>> -            host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>> +                          host->desc_sz;
>>           } else {
>>               host->adma_table_sz = host->adma_table_cnt *
>>                             SDHCI_ADMA2_32_DESC_SZ;
>
> Thanks Adrian for the suggestion. I will add this change.
>
> But even with this change, still i will have to override 
> 'host->desc_sz' variable since qcom sdhci controller expects/operates-on
>
> 12-byte descriptor as long was CQE is not enabled. When CQE is 
> enabled, it operates only on 16-bype descriptors (even when CQE is 
> halted).
>
> If i fix "host->desc_sz" to 16 then all the data transfer commands 
> during card initialization (till CQE is enabled) would fail.
>
> I may have to update as below:
>
>     host->desc_sz = 16;
>
>     sdhci_add_host()  ;
>
>    host->desc_sz = 12;
>
> And then cqhci_host_ops->enable() -> host->desc_sz = 16;
>
> Please let me know if this is fine or if you have any other suggestion 
> to support this limitation of qcom controller w.r.t ADMA descriptors 
> with CQE.
>
Hi Adrian,

Do you have any suggestions on the way to support both the descriptor sizes?

>>> +
>>> +    spin_lock_irqsave(&host->lock, flags);
>>> +
>>> +    /*
>>> +     * During CQE operation command complete bit gets latched.
>>> +     * So s/w should clear command complete interrupt status when 
>>> CQE is
>>> +     * halted. Otherwise unexpected SDCHI legacy interrupt gets
>>> +     * triggered when CQE is halted.
>>> +     */
>>> +    ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
>>> +    ctrl |= SDHCI_INT_RESPONSE;
>>> +    sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
>>> +    sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
>>> +
>>> +    spin_unlock_irqrestore(&host->lock, flags);
>>> +
>>> +    sdhci_cqe_disable(mmc, recovery);
>>> +}
>>> +
>>> +static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
>>> +    .enable        = sdhci_cqe_enable,
>>> +    .disable    = sdhci_msm_cqe_disable,
>>> +};
>>> +
>>> +static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
>>> +                struct platform_device *pdev)
>>> +{
>>> +    struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>>> +    struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
>>> +    struct cqhci_host *cq_host;
>>> +    bool dma64;
>>> +    int ret;
>>> +
>>> +    ret = sdhci_setup_host(host);
>>> +    if (ret)
>>> +        return ret;
>>> +
>>> +    cq_host = cqhci_pltfm_init(pdev);
>>> +    if (IS_ERR(cq_host)) {
>>> +        ret = PTR_ERR(cq_host);
>>> +        dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
>>> +        goto cleanup;
>>> +    }
>>> +
>>> +    msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
>>> +    cq_host->ops = &sdhci_msm_cqhci_ops;
>>> +
>>> +    dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
>>> +
>>> +    ret = cqhci_init(cq_host, host->mmc, dma64);
>>> +    if (ret) {
>>> +        dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
>>> +                mmc_hostname(host->mmc), ret);
>>> +        goto cleanup;
>>> +    }
>>> +
>>> +    /* Disable cqe reset due to cqe enable signal */
>>> +    cqhci_writel(cq_host, cqhci_readl(cq_host, CQHCI_VENDOR_CFG1) |
>>> +               DISABLE_RST_ON_CMDQ_EN, CQHCI_VENDOR_CFG1);
>>> +
>>> +    ret = __sdhci_add_host(host);
>>> +    if (ret)
>>> +        goto cleanup;
>>> +
>>> +    dev_info(&pdev->dev, "%s: CQE init: success\n",
>>> +            mmc_hostname(host->mmc));
>>> +    return ret;
>>> +
>>> +cleanup:
>>> +    sdhci_cleanup_host(host);
>>> +    return ret;
>>> +}
>>> +
>>>   /*
>>>    * Platform specific register write functions. This is so that, if 
>>> any
>>>    * register write needs to be followed up by platform specific 
>>> actions,
>>> @@ -1731,6 +1839,7 @@ static void 
>>> sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
>>>       .set_uhs_signaling = sdhci_msm_set_uhs_signaling,
>>>       .write_w = sdhci_msm_writew,
>>>       .write_b = sdhci_msm_writeb,
>>> +    .irq    = sdhci_msm_cqe_irq,
>>>   };
>>>     static const struct sdhci_pltfm_data sdhci_msm_pdata = {
>>> @@ -1754,6 +1863,7 @@ static int sdhci_msm_probe(struct 
>>> platform_device *pdev)
>>>       u8 core_major;
>>>       const struct sdhci_msm_offset *msm_offset;
>>>       const struct sdhci_msm_variant_info *var_info;
>>> +    struct device_node *node = pdev->dev.of_node;
>>>         host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, 
>>> sizeof(*msm_host));
>>>       if (IS_ERR(host))
>>> @@ -1952,7 +2062,10 @@ static int sdhci_msm_probe(struct 
>>> platform_device *pdev)
>>>       pm_runtime_use_autosuspend(&pdev->dev);
>>>         host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
>>> -    ret = sdhci_add_host(host);
>>> +    if (of_property_read_bool(node, "supports-cqe"))
>>> +        ret = sdhci_msm_cqe_add_host(host, pdev);
>>> +    else
>>> +        ret = sdhci_add_host(host);
>>>       if (ret)
>>>           goto pm_runtime_disable;
>>>       sdhci_msm_set_regulator_caps(msm_host);
>>>
Thanks

Veera

^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm
  2020-01-10  8:56     ` Veerabhadrarao Badiganti
@ 2020-01-13  7:24       ` Adrian Hunter
  2020-01-14  9:18         ` Veerabhadrarao Badiganti
  0 siblings, 1 reply; 6+ messages in thread
From: Adrian Hunter @ 2020-01-13  7:24 UTC (permalink / raw)
  To: Veerabhadrarao Badiganti, ulf.hansson, agross
  Cc: asutoshd, stummala, sayalil, cang, rampraka, linux-mmc,
	linux-kernel, linux-arm-msm, Ritesh Harjani

On 10/01/20 10:56 am, Veerabhadrarao Badiganti wrote:
> 
> On 1/2/2020 5:00 PM, Veerabhadrarao Badiganti wrote:
>>
>> On 12/20/2019 7:29 PM, Adrian Hunter wrote:
>>> On 17/12/19 2:37 pm, Veerabhadrarao Badiganti wrote:
>>>> From: Ritesh Harjani<riteshh@codeaurora.org>
>>>>
>>>> This adds CQHCI support for sdhci-msm platforms.
>>>>
>>>> Signed-off-by: Ritesh Harjani<riteshh@codeaurora.org>
>>>> Signed-off-by: Veerabhadrarao Badiganti<vbadigan@codeaurora.org>
>>>>
>>>> ---
>>>> This patch is based on RFC patch
>>>> https://lkml.org/lkml/2017/8/30/313
>>>>
>>>> Changes since RFC:
>>>>     - Updated settings so that TDLBA won't get reset when
>>>>       CQE is enabled.
>>>>     - Removed new compatible string and moved to supports-cqe
>>>>       dt flag to identify CQE support.
>>>>     - Incorporated review comments.
>>>>
>>>> Tested on: qcs404, sc7180
>>>> ---
>>>>   drivers/mmc/host/sdhci-msm.c | 115
>>>> ++++++++++++++++++++++++++++++++++++++++++-
>>>>   1 file changed, 114 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
>>>> index 3d0bb5e..a4e3507 100644
>>>> --- a/drivers/mmc/host/sdhci-msm.c
>>>> +++ b/drivers/mmc/host/sdhci-msm.c
>>>> @@ -15,6 +15,7 @@
>>>>   #include <linux/regulator/consumer.h>
>>>>     #include "sdhci-pltfm.h"
>>>> +#include "cqhci.h"
>>>>     #define CORE_MCI_VERSION        0x50
>>>>   #define CORE_VERSION_MAJOR_SHIFT    28
>>>> @@ -122,6 +123,10 @@
>>>>   #define msm_host_writel(msm_host, val, host, offset) \
>>>>       msm_host->var_ops->msm_writel_relaxed(val, host, offset)
>>>>   +/* CQHCI vendor specific registers */
>>>> +#define CQHCI_VENDOR_CFG1    0xA00
>>>> +#define DISABLE_RST_ON_CMDQ_EN    (0x3 << 13)
>>>> +
>>>>   struct sdhci_msm_offset {
>>>>       u32 core_hc_mode;
>>>>       u32 core_mci_data_cnt;
>>>> @@ -1567,6 +1572,109 @@ static void sdhci_msm_set_clock(struct
>>>> sdhci_host *host, unsigned int clock)
>>>>       __sdhci_msm_set_clock(host, clock);
>>>>   }
>>>> +/*****************************************************************************\
>>>>
>>>> + * *
>>>> + * MSM Command Queue Engine
>>>> (CQE)                                            *
>>>> + * *
>>>> +\*****************************************************************************/
>>>>
>>>> +
>>>> +static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
>>>> +{
>>>> +    int cmd_error = 0;
>>>> +    int data_error = 0;
>>>> +
>>>> +    if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
>>>> +        return intmask;
>>>> +
>>>> +    cqhci_irq(host->mmc, intmask, cmd_error, data_error);
>>>> +    return 0;
>>>> +}
>>>> +
>>>> +void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
>>>> +{
>>>> +    struct sdhci_host *host = mmc_priv(mmc);
>>>> +    unsigned long flags;
>>>> +    u32 ctrl;
>>>> +
>>>> +    /*
>>>> +     * When CQE is halted, the legacy SDHCI path operates only
>>>> +     * on 128bit descriptors in 64bit mode.
>>>> +     */
>>>> +    if (host->flags & SDHCI_USE_64_BIT_DMA)
>>>> +        host->desc_sz = 16;
>>> The adma_table_sz depends on desc_sz, so it cannot be changed here.
>>> If you do something like below, then you can set desc_sz before calling
>>> sdhci_setup_host()
>>>
>>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>>> index f4540f9892ce..f1d3b70ff769 100644
>>> --- a/drivers/mmc/host/sdhci.c
>>> +++ b/drivers/mmc/host/sdhci.c
>>> @@ -3825,9 +3825,10 @@ int sdhci_setup_host(struct sdhci_host *host)
>>>           void *buf;
>>>             if (host->flags & SDHCI_USE_64_BIT_DMA) {
>>> +            if (!host->desc_sz)
>>> +                host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>>>               host->adma_table_sz = host->adma_table_cnt *
>>> -                          SDHCI_ADMA2_64_DESC_SZ(host);
>>> -            host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>>> +                          host->desc_sz;
>>>           } else {
>>>               host->adma_table_sz = host->adma_table_cnt *
>>>                             SDHCI_ADMA2_32_DESC_SZ;
>>
>> Thanks Adrian for the suggestion. I will add this change.
>>
>> But even with this change, still i will have to override 'host->desc_sz'
>> variable since qcom sdhci controller expects/operates-on
>>
>> 12-byte descriptor as long was CQE is not enabled. When CQE is enabled, it
>> operates only on 16-bype descriptors (even when CQE is halted).
>>
>> If i fix "host->desc_sz" to 16 then all the data transfer commands during
>> card initialization (till CQE is enabled) would fail.
>>
>> I may have to update as below:
>>
>>     host->desc_sz = 16;
>>
>>     sdhci_add_host()  ;
>>
>>    host->desc_sz = 12;
>>
>> And then cqhci_host_ops->enable() -> host->desc_sz = 16;
>>
>> Please let me know if this is fine or if you have any other suggestion to
>> support this limitation of qcom controller w.r.t ADMA descriptors with CQE.
>>
> Hi Adrian,
> 
> Do you have any suggestions on the way to support both the descriptor sizes?

How about we have 2 variables: alloc_desc_sz and desc_sz
Then, in sdhci_setup_host():

	host->alloc_desc_sz = SDHCI_ADMA2_64/32_DESC_SZ(host);
	host->desc_sz = host->alloc_desc_sz;

Then desc_sz can be changed (in between requests) so long as desc_sz <
alloc_desc_sz.


> 
>>>> +
>>>> +    spin_lock_irqsave(&host->lock, flags);
>>>> +
>>>> +    /*
>>>> +     * During CQE operation command complete bit gets latched.
>>>> +     * So s/w should clear command complete interrupt status when CQE is
>>>> +     * halted. Otherwise unexpected SDCHI legacy interrupt gets
>>>> +     * triggered when CQE is halted.
>>>> +     */
>>>> +    ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
>>>> +    ctrl |= SDHCI_INT_RESPONSE;
>>>> +    sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
>>>> +    sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
>>>> +
>>>> +    spin_unlock_irqrestore(&host->lock, flags);
>>>> +
>>>> +    sdhci_cqe_disable(mmc, recovery);
>>>> +}
>>>> +
>>>> +static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
>>>> +    .enable        = sdhci_cqe_enable,
>>>> +    .disable    = sdhci_msm_cqe_disable,
>>>> +};
>>>> +
>>>> +static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
>>>> +                struct platform_device *pdev)
>>>> +{
>>>> +    struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>>>> +    struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
>>>> +    struct cqhci_host *cq_host;
>>>> +    bool dma64;
>>>> +    int ret;
>>>> +
>>>> +    ret = sdhci_setup_host(host);
>>>> +    if (ret)
>>>> +        return ret;
>>>> +
>>>> +    cq_host = cqhci_pltfm_init(pdev);
>>>> +    if (IS_ERR(cq_host)) {
>>>> +        ret = PTR_ERR(cq_host);
>>>> +        dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
>>>> +        goto cleanup;
>>>> +    }
>>>> +
>>>> +    msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
>>>> +    cq_host->ops = &sdhci_msm_cqhci_ops;
>>>> +
>>>> +    dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
>>>> +
>>>> +    ret = cqhci_init(cq_host, host->mmc, dma64);
>>>> +    if (ret) {
>>>> +        dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
>>>> +                mmc_hostname(host->mmc), ret);
>>>> +        goto cleanup;
>>>> +    }
>>>> +
>>>> +    /* Disable cqe reset due to cqe enable signal */
>>>> +    cqhci_writel(cq_host, cqhci_readl(cq_host, CQHCI_VENDOR_CFG1) |
>>>> +               DISABLE_RST_ON_CMDQ_EN, CQHCI_VENDOR_CFG1);
>>>> +
>>>> +    ret = __sdhci_add_host(host);
>>>> +    if (ret)
>>>> +        goto cleanup;
>>>> +
>>>> +    dev_info(&pdev->dev, "%s: CQE init: success\n",
>>>> +            mmc_hostname(host->mmc));
>>>> +    return ret;
>>>> +
>>>> +cleanup:
>>>> +    sdhci_cleanup_host(host);
>>>> +    return ret;
>>>> +}
>>>> +
>>>>   /*
>>>>    * Platform specific register write functions. This is so that, if any
>>>>    * register write needs to be followed up by platform specific actions,
>>>> @@ -1731,6 +1839,7 @@ static void sdhci_msm_set_regulator_caps(struct
>>>> sdhci_msm_host *msm_host)
>>>>       .set_uhs_signaling = sdhci_msm_set_uhs_signaling,
>>>>       .write_w = sdhci_msm_writew,
>>>>       .write_b = sdhci_msm_writeb,
>>>> +    .irq    = sdhci_msm_cqe_irq,
>>>>   };
>>>>     static const struct sdhci_pltfm_data sdhci_msm_pdata = {
>>>> @@ -1754,6 +1863,7 @@ static int sdhci_msm_probe(struct platform_device
>>>> *pdev)
>>>>       u8 core_major;
>>>>       const struct sdhci_msm_offset *msm_offset;
>>>>       const struct sdhci_msm_variant_info *var_info;
>>>> +    struct device_node *node = pdev->dev.of_node;
>>>>         host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
>>>>       if (IS_ERR(host))
>>>> @@ -1952,7 +2062,10 @@ static int sdhci_msm_probe(struct platform_device
>>>> *pdev)
>>>>       pm_runtime_use_autosuspend(&pdev->dev);
>>>>         host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
>>>> -    ret = sdhci_add_host(host);
>>>> +    if (of_property_read_bool(node, "supports-cqe"))
>>>> +        ret = sdhci_msm_cqe_add_host(host, pdev);
>>>> +    else
>>>> +        ret = sdhci_add_host(host);
>>>>       if (ret)
>>>>           goto pm_runtime_disable;
>>>>       sdhci_msm_set_regulator_caps(msm_host);
>>>>
> Thanks
> 
> Veera


^ permalink raw reply	[flat|nested] 6+ messages in thread

* Re: [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm
  2020-01-13  7:24       ` Adrian Hunter
@ 2020-01-14  9:18         ` Veerabhadrarao Badiganti
  0 siblings, 0 replies; 6+ messages in thread
From: Veerabhadrarao Badiganti @ 2020-01-14  9:18 UTC (permalink / raw)
  To: Adrian Hunter, ulf.hansson, agross
  Cc: asutoshd, stummala, sayalil, cang, rampraka, linux-mmc,
	linux-kernel, linux-arm-msm, Ritesh Harjani


On 1/13/2020 12:54 PM, Adrian Hunter wrote:
> On 10/01/20 10:56 am, Veerabhadrarao Badiganti wrote:
>> On 1/2/2020 5:00 PM, Veerabhadrarao Badiganti wrote:
>>> On 12/20/2019 7:29 PM, Adrian Hunter wrote:
>>>> On 17/12/19 2:37 pm, Veerabhadrarao Badiganti wrote:
>>>>> From: Ritesh Harjani<riteshh@codeaurora.org>
>>>>>
>>>>> This adds CQHCI support for sdhci-msm platforms.
>>>>>
>>>>> Signed-off-by: Ritesh Harjani<riteshh@codeaurora.org>
>>>>> Signed-off-by: Veerabhadrarao Badiganti<vbadigan@codeaurora.org>
>>>>>
>>>>> ---
>>>>> This patch is based on RFC patch
>>>>> https://lkml.org/lkml/2017/8/30/313
>>>>>
>>>>> Changes since RFC:
>>>>>      - Updated settings so that TDLBA won't get reset when
>>>>>        CQE is enabled.
>>>>>      - Removed new compatible string and moved to supports-cqe
>>>>>        dt flag to identify CQE support.
>>>>>      - Incorporated review comments.
>>>>>
>>>>> Tested on: qcs404, sc7180
>>>>> ---
>>>>>    drivers/mmc/host/sdhci-msm.c | 115
>>>>> ++++++++++++++++++++++++++++++++++++++++++-
>>>>>    1 file changed, 114 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
>>>>> index 3d0bb5e..a4e3507 100644
>>>>> --- a/drivers/mmc/host/sdhci-msm.c
>>>>> +++ b/drivers/mmc/host/sdhci-msm.c
>>>>> @@ -15,6 +15,7 @@
>>>>>    #include <linux/regulator/consumer.h>
>>>>>      #include "sdhci-pltfm.h"
>>>>> +#include "cqhci.h"
>>>>>      #define CORE_MCI_VERSION        0x50
>>>>>    #define CORE_VERSION_MAJOR_SHIFT    28
>>>>> @@ -122,6 +123,10 @@
>>>>>    #define msm_host_writel(msm_host, val, host, offset) \
>>>>>        msm_host->var_ops->msm_writel_relaxed(val, host, offset)
>>>>>    +/* CQHCI vendor specific registers */
>>>>> +#define CQHCI_VENDOR_CFG1    0xA00
>>>>> +#define DISABLE_RST_ON_CMDQ_EN    (0x3 << 13)
>>>>> +
>>>>>    struct sdhci_msm_offset {
>>>>>        u32 core_hc_mode;
>>>>>        u32 core_mci_data_cnt;
>>>>> @@ -1567,6 +1572,109 @@ static void sdhci_msm_set_clock(struct
>>>>> sdhci_host *host, unsigned int clock)
>>>>>        __sdhci_msm_set_clock(host, clock);
>>>>>    }
>>>>> +/*****************************************************************************\
>>>>>
>>>>> + * *
>>>>> + * MSM Command Queue Engine
>>>>> (CQE)                                            *
>>>>> + * *
>>>>> +\*****************************************************************************/
>>>>>
>>>>> +
>>>>> +static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
>>>>> +{
>>>>> +    int cmd_error = 0;
>>>>> +    int data_error = 0;
>>>>> +
>>>>> +    if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
>>>>> +        return intmask;
>>>>> +
>>>>> +    cqhci_irq(host->mmc, intmask, cmd_error, data_error);
>>>>> +    return 0;
>>>>> +}
>>>>> +
>>>>> +void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
>>>>> +{
>>>>> +    struct sdhci_host *host = mmc_priv(mmc);
>>>>> +    unsigned long flags;
>>>>> +    u32 ctrl;
>>>>> +
>>>>> +    /*
>>>>> +     * When CQE is halted, the legacy SDHCI path operates only
>>>>> +     * on 128bit descriptors in 64bit mode.
>>>>> +     */
>>>>> +    if (host->flags & SDHCI_USE_64_BIT_DMA)
>>>>> +        host->desc_sz = 16;
>>>> The adma_table_sz depends on desc_sz, so it cannot be changed here.
>>>> If you do something like below, then you can set desc_sz before calling
>>>> sdhci_setup_host()
>>>>
>>>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>>>> index f4540f9892ce..f1d3b70ff769 100644
>>>> --- a/drivers/mmc/host/sdhci.c
>>>> +++ b/drivers/mmc/host/sdhci.c
>>>> @@ -3825,9 +3825,10 @@ int sdhci_setup_host(struct sdhci_host *host)
>>>>            void *buf;
>>>>              if (host->flags & SDHCI_USE_64_BIT_DMA) {
>>>> +            if (!host->desc_sz)
>>>> +                host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>>>>                host->adma_table_sz = host->adma_table_cnt *
>>>> -                          SDHCI_ADMA2_64_DESC_SZ(host);
>>>> -            host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
>>>> +                          host->desc_sz;
>>>>            } else {
>>>>                host->adma_table_sz = host->adma_table_cnt *
>>>>                              SDHCI_ADMA2_32_DESC_SZ;
>>> Thanks Adrian for the suggestion. I will add this change.
>>>
>>> But even with this change, still i will have to override 'host->desc_sz'
>>> variable since qcom sdhci controller expects/operates-on
>>>
>>> 12-byte descriptor as long was CQE is not enabled. When CQE is enabled, it
>>> operates only on 16-bype descriptors (even when CQE is halted).
>>>
>>> If i fix "host->desc_sz" to 16 then all the data transfer commands during
>>> card initialization (till CQE is enabled) would fail.
>>>
>>> I may have to update as below:
>>>
>>>      host->desc_sz = 16;
>>>
>>>      sdhci_add_host()  ;
>>>
>>>     host->desc_sz = 12;
>>>
>>> And then cqhci_host_ops->enable() -> host->desc_sz = 16;
>>>
>>> Please let me know if this is fine or if you have any other suggestion to
>>> support this limitation of qcom controller w.r.t ADMA descriptors with CQE.
>>>
>> Hi Adrian,
>>
>> Do you have any suggestions on the way to support both the descriptor sizes?
> How about we have 2 variables: alloc_desc_sz and desc_sz
> Then, in sdhci_setup_host():
>
> 	host->alloc_desc_sz = SDHCI_ADMA2_64/32_DESC_SZ(host);
> 	host->desc_sz = host->alloc_desc_sz;
>
> Then desc_sz can be changed (in between requests) so long as desc_sz <
> alloc_desc_sz.

Thanks Adrian.  Then I will update it with two variables.

>>>>> +
>>>>> +    spin_lock_irqsave(&host->lock, flags);
>>>>> +
>>>>> +    /*
>>>>> +     * During CQE operation command complete bit gets latched.
>>>>> +     * So s/w should clear command complete interrupt status when CQE is
>>>>> +     * halted. Otherwise unexpected SDCHI legacy interrupt gets
>>>>> +     * triggered when CQE is halted.
>>>>> +     */
>>>>> +    ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
>>>>> +    ctrl |= SDHCI_INT_RESPONSE;
>>>>> +    sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
>>>>> +    sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
>>>>> +
>>>>> +    spin_unlock_irqrestore(&host->lock, flags);
>>>>> +
>>>>> +    sdhci_cqe_disable(mmc, recovery);
>>>>> +}
>>>>> +
>>>>> +static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
>>>>> +    .enable        = sdhci_cqe_enable,
>>>>> +    .disable    = sdhci_msm_cqe_disable,
>>>>> +};
>>>>> +
>>>>> +static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
>>>>> +                struct platform_device *pdev)
>>>>> +{
>>>>> +    struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>>>>> +    struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
>>>>> +    struct cqhci_host *cq_host;
>>>>> +    bool dma64;
>>>>> +    int ret;
>>>>> +
>>>>> +    ret = sdhci_setup_host(host);
>>>>> +    if (ret)
>>>>> +        return ret;
>>>>> +
>>>>> +    cq_host = cqhci_pltfm_init(pdev);
>>>>> +    if (IS_ERR(cq_host)) {
>>>>> +        ret = PTR_ERR(cq_host);
>>>>> +        dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
>>>>> +        goto cleanup;
>>>>> +    }
>>>>> +
>>>>> +    msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
>>>>> +    cq_host->ops = &sdhci_msm_cqhci_ops;
>>>>> +
>>>>> +    dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
>>>>> +
>>>>> +    ret = cqhci_init(cq_host, host->mmc, dma64);
>>>>> +    if (ret) {
>>>>> +        dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
>>>>> +                mmc_hostname(host->mmc), ret);
>>>>> +        goto cleanup;
>>>>> +    }
>>>>> +
>>>>> +    /* Disable cqe reset due to cqe enable signal */
>>>>> +    cqhci_writel(cq_host, cqhci_readl(cq_host, CQHCI_VENDOR_CFG1) |
>>>>> +               DISABLE_RST_ON_CMDQ_EN, CQHCI_VENDOR_CFG1);
>>>>> +
>>>>> +    ret = __sdhci_add_host(host);
>>>>> +    if (ret)
>>>>> +        goto cleanup;
>>>>> +
>>>>> +    dev_info(&pdev->dev, "%s: CQE init: success\n",
>>>>> +            mmc_hostname(host->mmc));
>>>>> +    return ret;
>>>>> +
>>>>> +cleanup:
>>>>> +    sdhci_cleanup_host(host);
>>>>> +    return ret;
>>>>> +}
>>>>> +
>>>>>    /*
>>>>>     * Platform specific register write functions. This is so that, if any
>>>>>     * register write needs to be followed up by platform specific actions,
>>>>> @@ -1731,6 +1839,7 @@ static void sdhci_msm_set_regulator_caps(struct
>>>>> sdhci_msm_host *msm_host)
>>>>>        .set_uhs_signaling = sdhci_msm_set_uhs_signaling,
>>>>>        .write_w = sdhci_msm_writew,
>>>>>        .write_b = sdhci_msm_writeb,
>>>>> +    .irq    = sdhci_msm_cqe_irq,
>>>>>    };
>>>>>      static const struct sdhci_pltfm_data sdhci_msm_pdata = {
>>>>> @@ -1754,6 +1863,7 @@ static int sdhci_msm_probe(struct platform_device
>>>>> *pdev)
>>>>>        u8 core_major;
>>>>>        const struct sdhci_msm_offset *msm_offset;
>>>>>        const struct sdhci_msm_variant_info *var_info;
>>>>> +    struct device_node *node = pdev->dev.of_node;
>>>>>          host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
>>>>>        if (IS_ERR(host))
>>>>> @@ -1952,7 +2062,10 @@ static int sdhci_msm_probe(struct platform_device
>>>>> *pdev)
>>>>>        pm_runtime_use_autosuspend(&pdev->dev);
>>>>>          host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
>>>>> -    ret = sdhci_add_host(host);
>>>>> +    if (of_property_read_bool(node, "supports-cqe"))
>>>>> +        ret = sdhci_msm_cqe_add_host(host, pdev);
>>>>> +    else
>>>>> +        ret = sdhci_add_host(host);
>>>>>        if (ret)
>>>>>            goto pm_runtime_disable;
>>>>>        sdhci_msm_set_regulator_caps(msm_host);
>>>>>
>> Thanks
>>
>> Veera

^ permalink raw reply	[flat|nested] 6+ messages in thread

end of thread, other threads:[~2020-01-14  9:18 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-17 12:37 [PATCH V1] mmc: sdhci-msm: Add CQHCI support for sdhci-msm Veerabhadrarao Badiganti
2019-12-20 13:59 ` Adrian Hunter
2020-01-02 11:30   ` Veerabhadrarao Badiganti
2020-01-10  8:56     ` Veerabhadrarao Badiganti
2020-01-13  7:24       ` Adrian Hunter
2020-01-14  9:18         ` Veerabhadrarao Badiganti

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.