[PATCH v4 net-next 00/19] net: mvpp2: Add TX Flow Control support

[PATCH v4 net-next 00/19] net: mvpp2: Add TX Flow Control support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Armada hardware has a pause generation mechanism in GOP (MAC).
The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.

Problem is that Packet Processor that actually can drop packets due to lack of resources not connected to the GOP flow control generation mechanism.
To solve this issue Armada has firmware running on CM3 CPU dedicated for Flow Control support.
Firmware monitors Packet Processor resources and asserts XON/XOFF by writing to Ports Control 0 Register.

MSS shared SRAM memory used to communicate between CM3 firmware and PP2 driver.
During init PP2 driver informs firmware about used BM pools, RXQs, congestion and depletion thresholds.

The pause frames are generated whenever congestion or depletion in resources is detected.
The back pressure is stopped when the resource reaches a sufficient level.
So the congestion/depletion and sufficient level implement a hysteresis that reduces the XON/XOFF toggle frequency.

Packet Processor v23 hardware introduces support for RX FIFO fill level monitor.
Patch "add PPv23 version definition" to differ between v23 and v22 hardware.
Patch "add TX FC firmware check" verifies that CM3 firmware supports Flow Control monitoring.

v3 --> v4
- Remove RFC tag

v2 --> v3
- Remove inline functions
- Add PPv2.3 description into marvell-pp2.txt
- Improve mvpp2_interrupts_mask/unmask procedure
- Improve FC enable/disable procedure
- Add priv->sram_pool check
- Remove gen_pool_destroy call
- Reduce Flow Control timer to x100 faster

v1 --> v2
- Add memory requirements information
- Add EPROBE_DEFER if of_gen_pool_get return NULL
- Move Flow control configuration to mvpp2_mac_link_up callback
- Add firmware version info with Flow control support

Konstantin Porotchkin (1):
  dts: marvell: add CM3 SRAM memory to cp115 ethernet device tree

Stefan Chulski (18):
  doc: marvell: add cm3-mem device tree bindings description
  net: mvpp2: add CM3 SRAM memory map
  doc: marvell: add PPv2.3 description to marvell-pp2.txt
  net: mvpp2: add PPv23 version definition
  net: mvpp2: always compare hw-version vs MVPP21
  net: mvpp2: increase BM pool size to 2048 buffers
  net: mvpp2: increase RXQ size to 1024 descriptors
  net: mvpp2: add FCA periodic timer configurations
  net: mvpp2: add FCA RXQ non occupied descriptor threshold
  net: mvpp2: add spinlock for FW FCA configuration path
  net: mvpp2: enable global flow control
  net: mvpp2: add RXQ flow control configurations
  net: mvpp2: add ethtool flow control configuration support
  net: mvpp2: add BM protection underrun feature support
  net: mvpp2: add PPv23 RX FIFO flow control
  net: mvpp2: set 802.3x GoP Flow Control mode
  net: mvpp2: limit minimum ring size to 1024 descriptors
  net: mvpp2: add TX FC firmware check

 Documentation/devicetree/bindings/net/marvell-pp2.txt |   4 +-
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi         |  10 +
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h            | 130 ++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c       | 564 ++++++++++++++++++--
 4 files changed, 658 insertions(+), 50 deletions(-)

-- 
1.9.1

[PATCH v4 net-next 01/19] doc: marvell: add cm3-mem device tree bindings description

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 Documentation/devicetree/bindings/net/marvell-pp2.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index b783976..f9f8cc6 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -37,6 +37,7 @@ Required properties (port):
   GOP (Group Of Ports) point of view. This ID is used to index the
   per-port registers in the second register area.
 - phy-mode: See ethernet.txt file in the same directory
+- cm3-mem: phandle to CM3 SRAM definitions
 
 Optional properties (port):
 
-- 
1.9.1

[PATCH v4 net-next 02/19] dts: marvell: add CM3 SRAM memory to cp115 ethernet device tree

[stefanc]

From: Konstantin Porotchkin <kostap@marvell.com>

CM3 SRAM address space would be used for Flow Control configuration.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 9dcf16b..359cf42 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -69,6 +69,8 @@
 			status = "disabled";
 			dma-coherent;
 
+			cm3-mem = <&CP11X_LABEL(cm3_sram)>;
+
 			CP11X_LABEL(eth0): eth0 {
 				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
 					<43 IRQ_TYPE_LEVEL_HIGH>,
@@ -211,6 +213,14 @@
 			};
 		};
 
+		CP11X_LABEL(cm3_sram): cm3@220000 {
+			compatible = "mmio-sram";
+			reg = <0x220000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x220000 0x800>;
+		};
+
 		CP11X_LABEL(rtc): rtc@284000 {
 			compatible = "marvell,armada-8k-rtc";
 			reg = <0x284000 0x20>, <0x284080 0x24>;
-- 
1.9.1

[PATCH v4 net-next 03/19] net: mvpp2: add CM3 SRAM memory map

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch adds CM3 memory map and CM3 read/write callbacks.
No functionality changes.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  7 ++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 73 +++++++++++++++++++-
 2 files changed, 77 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 6bd7e40..aec9179 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -748,6 +748,9 @@
 #define MVPP2_TX_FIFO_THRESHOLD(kb)	\
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
+/* MSS Flow control */
+#define MSS_SRAM_SIZE	0x800
+
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
 	SKB_DATA_ALIGN(sizeof(struct skb_shared_info))
@@ -925,6 +928,7 @@ struct mvpp2 {
 	/* Shared registers' base addresses */
 	void __iomem *lms_base;
 	void __iomem *iface_base;
+	void __iomem *cm3_base;
 
 	/* On PPv2.2, each "software thread" can access the base
 	 * register through a separate address space, each 64 KB apart
@@ -996,6 +1000,9 @@ struct mvpp2 {
 
 	/* page_pool allocator */
 	struct page_pool *page_pool[MVPP2_PORT_MAX_RXQ];
+
+	/* CM3 SRAM pool */
+	struct gen_pool *sram_pool;
 };
 
 struct mvpp2_pcpu_stats {
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index a07cf60..501b17e 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -25,6 +25,7 @@
 #include <linux/of_net.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
+#include <linux/genalloc.h>
 #include <linux/phy.h>
 #include <linux/phylink.h>
 #include <linux/phy/phy.h>
@@ -91,6 +92,16 @@ static inline u32 mvpp2_cpu_to_thread(struct mvpp2 *priv, int cpu)
 	return cpu % priv->nthreads;
 }
 
+static void mvpp2_cm3_write(struct mvpp2 *priv, u32 offset, u32 data)
+{
+	writel(data, priv->cm3_base + offset);
+}
+
+static u32 mvpp2_cm3_read(struct mvpp2 *priv, u32 offset)
+{
+	return readl(priv->cm3_base + offset);
+}
+
 static struct page_pool *
 mvpp2_create_page_pool(struct device *dev, int num, int len,
 		       enum dma_data_direction dma_dir)
@@ -6846,6 +6857,44 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	return 0;
 }
 
+static int mvpp2_get_sram(struct platform_device *pdev,
+			  struct mvpp2 *priv)
+{
+	struct device_node *dn = pdev->dev.of_node;
+	static bool defer_once;
+	struct resource *res;
+
+	if (has_acpi_companion(&pdev->dev)) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+		if (!res) {
+			dev_warn(&pdev->dev, "ACPI is too old, Flow control not supported\n");
+			return 0;
+		}
+		priv->cm3_base = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(priv->cm3_base))
+			return PTR_ERR(priv->cm3_base);
+	} else {
+		priv->sram_pool = of_gen_pool_get(dn, "cm3-mem", 0);
+		if (!priv->sram_pool) {
+			if (!defer_once) {
+				defer_once = true;
+				/* Try defer once */
+				return -EPROBE_DEFER;
+			}
+			dev_warn(&pdev->dev, "DT is too old, Flow control not supported\n");
+			return -ENOMEM;
+		}
+		/* cm3_base allocated with offset zero into the SRAM since mapping size
+		 * is equal to requested size.
+		 */
+		priv->cm3_base = (void __iomem *)gen_pool_alloc(priv->sram_pool,
+								MSS_SRAM_SIZE);
+		if (!priv->cm3_base)
+			return -ENOMEM;
+	}
+	return 0;
+}
+
 static int mvpp2_probe(struct platform_device *pdev)
 {
 	const struct acpi_device_id *acpi_id;
@@ -6902,6 +6951,13 @@ static int mvpp2_probe(struct platform_device *pdev)
 		priv->iface_base = devm_ioremap_resource(&pdev->dev, res);
 		if (IS_ERR(priv->iface_base))
 			return PTR_ERR(priv->iface_base);
+
+		/* Map CM3 SRAM */
+		err = mvpp2_get_sram(pdev, priv);
+		if (err == -EPROBE_DEFER)
+			return err;
+		else if (err)
+			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
 	}
 
 	if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
@@ -6947,11 +7003,13 @@ static int mvpp2_probe(struct platform_device *pdev)
 
 	if (dev_of_node(&pdev->dev)) {
 		priv->pp_clk = devm_clk_get(&pdev->dev, "pp_clk");
-		if (IS_ERR(priv->pp_clk))
-			return PTR_ERR(priv->pp_clk);
+		if (IS_ERR(priv->pp_clk)) {
+			err = PTR_ERR(priv->pp_clk);
+			goto err_cm3;
+		}
 		err = clk_prepare_enable(priv->pp_clk);
 		if (err < 0)
-			return err;
+			goto err_cm3;
 
 		priv->gop_clk = devm_clk_get(&pdev->dev, "gop_clk");
 		if (IS_ERR(priv->gop_clk)) {
@@ -7087,6 +7145,11 @@ static int mvpp2_probe(struct platform_device *pdev)
 	clk_disable_unprepare(priv->gop_clk);
 err_pp_clk:
 	clk_disable_unprepare(priv->pp_clk);
+err_cm3:
+	if (priv->sram_pool && priv->cm3_base)
+		gen_pool_free(priv->sram_pool, (unsigned long)priv->cm3_base,
+			      MSS_SRAM_SIZE);
+
 	return err;
 }
 
@@ -7127,6 +7190,10 @@ static int mvpp2_remove(struct platform_device *pdev)
 				  aggr_txq->descs_dma);
 	}
 
+	if (priv->sram_pool && priv->cm3_base)
+		gen_pool_free(priv->sram_pool, (unsigned long)priv->cm3_base,
+			      MSS_SRAM_SIZE);
+
 	if (is_acpi_node(port_fwnode))
 		return 0;
 
-- 
1.9.1

[PATCH v4 net-next 04/19] doc: marvell: add PPv2.3 description to marvell-pp2.txt

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 Documentation/devicetree/bindings/net/marvell-pp2.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index f9f8cc6..df80cff 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -1,5 +1,6 @@
 * Marvell Armada 375 Ethernet Controller (PPv2.1)
   Marvell Armada 7K/8K Ethernet Controller (PPv2.2)
+  Marvell CN913X Ethernet Controller (PPv2.3)
 
 Required properties:
 
@@ -12,7 +13,7 @@ Required properties:
 	- common controller registers
 	- LMS registers
 	- one register area per Ethernet port
-  For "marvell,armada-7k-pp2", must contain the following register
+  For "marvell,armada-7k-pp2" used by 7K/8K and CN913X, must contain the following register
   sets:
 	- packet processor registers
 	- networking interfaces registers
-- 
1.9.1

[PATCH v4 net-next 05/19] net: mvpp2: add PPv23 version definition

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 24 ++++++++++++--------
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 17 +++++++++-----
 2 files changed, 25 insertions(+), 16 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index aec9179..89b3ede 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -60,6 +60,9 @@
 /* Top Registers */
 #define MVPP2_MH_REG(port)			(0x5040 + 4 * (port))
 #define MVPP2_DSA_EXTENDED			BIT(5)
+#define MVPP2_VER_ID_REG			0x50b0
+#define MVPP2_VER_PP22				0x10
+#define MVPP2_VER_PP23				0x11
 
 /* Parser Registers */
 #define MVPP2_PRS_INIT_LOOKUP_REG		0x1000
@@ -469,7 +472,7 @@
 #define     MVPP22_GMAC_INT_SUM_MASK_LINK_STAT	BIT(1)
 #define	    MVPP22_GMAC_INT_SUM_MASK_PTP	BIT(2)
 
-/* Per-port XGMAC registers. PPv2.2 only, only for GOP port 0,
+/* Per-port XGMAC registers. PPv2.2 and PPv2.3, only for GOP port 0,
  * relative to port->base.
  */
 #define MVPP22_XLG_CTRL0_REG			0x100
@@ -506,7 +509,7 @@
 #define     MVPP22_XLG_CTRL4_MACMODSELECT_GMAC	BIT(12)
 #define     MVPP22_XLG_CTRL4_EN_IDLE_CHECK	BIT(14)
 
-/* SMI registers. PPv2.2 only, relative to priv->iface_base. */
+/* SMI registers. PPv2.2 and PPv2.3, relative to priv->iface_base. */
 #define MVPP22_SMI_MISC_CFG_REG			0x1204
 #define     MVPP22_SMI_POLLING_EN		BIT(10)
 
@@ -582,7 +585,7 @@
 #define MVPP2_QUEUE_NEXT_DESC(q, index) \
 	(((index) < (q)->last_desc) ? ((index) + 1) : 0)
 
-/* XPCS registers. PPv2.2 only */
+/* XPCS registers.PPv2.2 and PPv2.3 */
 #define MVPP22_MPCS_BASE(port)			(0x7000 + (port) * 0x1000)
 #define MVPP22_MPCS_CTRL			0x14
 #define     MVPP22_MPCS_CTRL_FWD_ERR_CONN	BIT(10)
@@ -593,7 +596,7 @@
 #define     MVPP22_MPCS_CLK_RESET_DIV_RATIO(n)	((n) << 4)
 #define     MVPP22_MPCS_CLK_RESET_DIV_SET	BIT(11)
 
-/* XPCS registers. PPv2.2 only */
+/* XPCS registers. PPv2.2 and PPv2.3 */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0
 #define     MVPP22_XPCS_CFG0_RESET_DIS		BIT(0)
@@ -930,15 +933,16 @@ struct mvpp2 {
 	void __iomem *iface_base;
 	void __iomem *cm3_base;
 
-	/* On PPv2.2, each "software thread" can access the base
+	/* On PPv2.2 and PPv2.3, each "software thread" can access the base
 	 * register through a separate address space, each 64 KB apart
 	 * from each other. Typically, such address spaces will be
 	 * used per CPU.
 	 */
 	void __iomem *swth_base[MVPP2_MAX_THREADS];
 
-	/* On PPv2.2, some port control registers are located into the system
-	 * controller space. These registers are accessible through a regmap.
+	/* On PPv2.2 and PPv2.3, some port control registers are located into
+	 * the system controller space. These registers are accessible
+	 * through a regmap.
 	 */
 	struct regmap *sysctrl_base;
 
@@ -980,7 +984,7 @@ struct mvpp2 {
 	u32 tclk;
 
 	/* HW version */
-	enum { MVPP21, MVPP22 } hw_version;
+	enum { MVPP21, MVPP22, MVPP23 } hw_version;
 
 	/* Maximum number of RXQs per port */
 	unsigned int max_port_rxqs;
@@ -1227,7 +1231,7 @@ struct mvpp21_rx_desc {
 	__le32 reserved8;
 };
 
-/* HW TX descriptor for PPv2.2 */
+/* HW TX descriptor for PPv2.2 and PPv2.3 */
 struct mvpp22_tx_desc {
 	__le32 command;
 	u8  packet_offset;
@@ -1239,7 +1243,7 @@ struct mvpp22_tx_desc {
 	__le64 buf_cookie_misc;
 };
 
-/* HW RX descriptor for PPv2.2 */
+/* HW RX descriptor for PPv2.2 and PPv2.3 */
 struct mvpp22_rx_desc {
 	__le32 status;
 	__le16 reserved1;
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 4b07f6c..4f482ad 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -395,7 +395,7 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 	if (!IS_ALIGNED(size, 16))
 		return -EINVAL;
 
-	/* PPv2.1 needs 8 bytes per buffer pointer, PPv2.2 needs 16
+	/* PPv2.1 needs 8 bytes per buffer pointer, PPv2.2 and PPv2.3 needs 16
 	 * bytes per buffer pointer
 	 */
 	if (priv->hw_version == MVPP21)
@@ -1183,7 +1183,7 @@ static void mvpp2_interrupts_unmask(void *arg)
 	u32 val;
 	int i;
 
-	if (port->priv->hw_version != MVPP22)
+	if (port->priv->hw_version == MVPP21)
 		return;
 
 	if (mask)
@@ -5467,7 +5467,7 @@ static void mvpp2_rx_irqs_setup(struct mvpp2_port *port)
 		return;
 	}
 
-	/* Handle the more complicated PPv2.2 case */
+	/* Handle the more complicated PPv2.2 and PPv2.3 case */
 	for (i = 0; i < port->nqvecs; i++) {
 		struct mvpp2_queue_vector *qv = port->qvecs + i;
 
@@ -5644,7 +5644,7 @@ static bool mvpp22_port_has_legacy_tx_irqs(struct device_node *port_node,
 
 /* Checks if the port dt description has the required Tx interrupts:
  * - PPv2.1: there are no such interrupts.
- * - PPv2.2:
+ * - PPv2.2 and PPv2.3:
  *   - The old DTs have: "rx-shared", "tx-cpuX" with X in [0...3]
  *   - The new ones have: "hifX" with X in [0..8]
  *
@@ -6632,7 +6632,7 @@ static void mvpp22_rx_fifo_set_hw(struct mvpp2 *priv, int port, int data_size)
 	mvpp2_write(priv, MVPP2_RX_ATTR_FIFO_SIZE_REG(port), attr_size);
 }
 
-/* Initialize TX FIFO's: the total FIFO size is 48kB on PPv2.2.
+/* Initialize TX FIFO's: the total FIFO size is 48kB on PPv2.2 and PPv2.3.
  * 4kB fixed space must be assigned for the loopback port.
  * Redistribute remaining avialable 44kB space among all active ports.
  * Guarantee minimum 32kB for 10G port and 8kB for port 1, capable of 2.5G
@@ -6689,7 +6689,7 @@ static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
 	mvpp2_write(priv, MVPP22_TX_FIFO_THRESH_REG(port), threshold);
 }
 
-/* Initialize TX FIFO's: the total FIFO size is 19kB on PPv2.2.
+/* Initialize TX FIFO's: the total FIFO size is 19kB on PPv2.2 and PPv2.3.
  * 3kB fixed space must be assigned for the loopback port.
  * Redistribute remaining avialable 16kB space among all active ports.
  * The 10G interface should use 10kB (which is maximum possible size
@@ -7081,6 +7081,11 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->port_map |= BIT(i);
 	}
 
+	if (priv->hw_version != MVPP21) {
+		if (mvpp2_read(priv, MVPP2_VER_ID_REG) == MVPP2_VER_PP23)
+			priv->hw_version = MVPP23;
+	}
+
 	/* Initialize network controller */
 	err = mvpp2_init(pdev, priv);
 	if (err < 0) {
-- 
1.9.1

[PATCH v4 net-next 06/19] net: mvpp2: always compare hw-version vs MVPP21

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 36 ++++++++++----------
 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 4f482ad..409ca64 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -330,7 +330,7 @@ static int mvpp2_get_nrxqs(struct mvpp2 *priv)
 {
 	unsigned int nrxqs;
 
-	if (priv->hw_version == MVPP22 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
+	if (priv->hw_version != MVPP21 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
 		return 1;
 
 	/* According to the PPv2.2 datasheet and our experiments on
@@ -457,7 +457,7 @@ static void mvpp2_bm_bufs_get_addrs(struct device *dev, struct mvpp2 *priv,
 				      MVPP2_BM_PHY_ALLOC_REG(bm_pool->id));
 	*phys_addr = mvpp2_thread_read(priv, thread, MVPP2_BM_VIRT_ALLOC_REG);
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		u32 val;
 		u32 dma_addr_highbits, phys_addr_highbits;
 
@@ -753,7 +753,7 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 	if (test_bit(thread, &port->priv->lock_map))
 		spin_lock_irqsave(&port->bm_lock[thread], flags);
 
-	if (port->priv->hw_version == MVPP22) {
+	if (port->priv->hw_version != MVPP21) {
 		u32 val = 0;
 
 		if (sizeof(dma_addr_t) == 8)
@@ -1210,7 +1210,7 @@ static bool mvpp2_port_supports_xlg(struct mvpp2_port *port)
 
 static bool mvpp2_port_supports_rgmii(struct mvpp2_port *port)
 {
-	return !(port->priv->hw_version == MVPP22 && port->gop_id == 0);
+	return !(port->priv->hw_version != MVPP21 && port->gop_id == 0);
 }
 
 /* Port configuration routines */
@@ -1828,7 +1828,7 @@ static void mvpp2_mac_reset_assert(struct mvpp2_port *port)
 	      MVPP2_GMAC_PORT_RESET_MASK;
 	writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
 
-	if (port->priv->hw_version == MVPP22 && port->gop_id == 0) {
+	if (port->priv->hw_version != MVPP21 && port->gop_id == 0) {
 		val = readl(port->base + MVPP22_XLG_CTRL0_REG) &
 		      ~MVPP22_XLG_CTRL0_MAC_RESET_DIS;
 		writel(val, port->base + MVPP22_XLG_CTRL0_REG);
@@ -1841,7 +1841,7 @@ static void mvpp22_pcs_reset_assert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -1862,7 +1862,7 @@ static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -4199,7 +4199,7 @@ static void mvpp2_start_dev(struct mvpp2_port *port)
 	/* Enable interrupts on all threads */
 	mvpp2_interrupts_enable(port);
 
-	if (port->priv->hw_version == MVPP22)
+	if (port->priv->hw_version != MVPP21)
 		mvpp22_mode_reconfigure(port);
 
 	if (port->phylink) {
@@ -4415,7 +4415,7 @@ static int mvpp2_open(struct net_device *dev)
 		valid = true;
 	}
 
-	if (priv->hw_version == MVPP22 && port->port_irq) {
+	if (priv->hw_version != MVPP21 && port->port_irq) {
 		err = request_irq(port->port_irq, mvpp2_port_isr, 0,
 				  dev->name, port);
 		if (err) {
@@ -6063,7 +6063,7 @@ static int mvpp2__mac_prepare(struct phylink_config *config, unsigned int mode,
 			     MVPP2_GMAC_PORT_RESET_MASK,
 			     MVPP2_GMAC_PORT_RESET_MASK);
 
-		if (port->priv->hw_version == MVPP22) {
+		if (port->priv->hw_version != MVPP21) {
 			mvpp22_gop_mask_irq(port);
 
 			phy_power_off(port->comphy);
@@ -6117,7 +6117,7 @@ static int mvpp2_mac_finish(struct phylink_config *config, unsigned int mode,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 
-	if (port->priv->hw_version == MVPP22 &&
+	if (port->priv->hw_version != MVPP21 &&
 	    port->phy_interface != interface) {
 		port->phy_interface = interface;
 
@@ -6797,7 +6797,7 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	if (dram_target_info)
 		mvpp2_conf_mbus_windows(dram_target_info, priv);
 
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		mvpp2_axi_init(priv);
 
 	/* Disable HW PHY polling */
@@ -6960,7 +6960,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
 	}
 
-	if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
+	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
 		priv->sysctrl_base =
 			syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
 							"marvell,system-controller");
@@ -6973,7 +6973,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->sysctrl_base = NULL;
 	}
 
-	if (priv->hw_version == MVPP22 &&
+	if (priv->hw_version != MVPP21 &&
 	    mvpp2_get_nrxqs(priv) * 2 <= MVPP2_BM_MAX_POOLS)
 		priv->percpu_pools = 1;
 
@@ -7020,7 +7020,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		if (err < 0)
 			goto err_pp_clk;
 
-		if (priv->hw_version == MVPP22) {
+		if (priv->hw_version != MVPP21) {
 			priv->mg_clk = devm_clk_get(&pdev->dev, "mg_clk");
 			if (IS_ERR(priv->mg_clk)) {
 				err = PTR_ERR(priv->mg_clk);
@@ -7061,7 +7061,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		err = dma_set_mask(&pdev->dev, MVPP2_DESC_DMA_MASK);
 		if (err)
 			goto err_axi_clk;
@@ -7141,10 +7141,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 	clk_disable_unprepare(priv->axi_clk);
 
 err_mg_core_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_core_clk);
 err_mg_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_clk);
 err_gop_clk:
 	clk_disable_unprepare(priv->gop_clk);
-- 
1.9.1

[PATCH v4 net-next 07/19] net: mvpp2: increase BM pool size to 2048 buffers

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

BM pool size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC is 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.

Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 89b3ede..8dc669d 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -851,8 +851,8 @@ enum mvpp22_ptp_packet_format {
 #define MVPP22_PTP_TIMESTAMPQUEUESELECT	BIT(18)
 
 /* BM constants */
-#define MVPP2_BM_JUMBO_BUF_NUM		512
-#define MVPP2_BM_LONG_BUF_NUM		1024
+#define MVPP2_BM_JUMBO_BUF_NUM		2048
+#define MVPP2_BM_LONG_BUF_NUM		2048
 #define MVPP2_BM_SHORT_BUF_NUM		2048
 #define MVPP2_BM_POOL_SIZE_MAX		(16*1024 - MVPP2_BM_POOL_PTR_ALIGN/4)
 #define MVPP2_BM_POOL_PTR_ALIGN		128
-- 
1.9.1

[PATCH v4 net-next 08/19] net: mvpp2: increase RXQ size to 1024 descriptors

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC is 1024 buffers.
Default set to 1024 descriptors and maximum size to 2048.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 8dc669d..cac9885 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -715,8 +715,8 @@
 #define MVPP2_PORT_MAX_RXQ		32
 
 /* Max number of Rx descriptors */
-#define MVPP2_MAX_RXD_MAX		1024
-#define MVPP2_MAX_RXD_DFLT		128
+#define MVPP2_MAX_RXD_MAX		2048
+#define MVPP2_MAX_RXD_DFLT		1024
 
 /* Max number of Tx descriptors */
 #define MVPP2_MAX_TXD_MAX		2048
-- 
1.9.1

[PATCH v4 net-next 09/19] net: mvpp2: add FCA periodic timer configurations

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 +++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 45 ++++++++++++++++++++
 2 files changed, 57 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index cac9885..73f087c 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -596,6 +596,15 @@
 #define     MVPP22_MPCS_CLK_RESET_DIV_RATIO(n)	((n) << 4)
 #define     MVPP22_MPCS_CLK_RESET_DIV_SET	BIT(11)
 
+/* FCA registers. PPv2.2 and PPv2.3 */
+#define MVPP22_FCA_BASE(port)			(0x7600 + (port) * 0x1000)
+#define MVPP22_FCA_REG_SIZE			16
+#define MVPP22_FCA_REG_MASK			0xFFFF
+#define MVPP22_FCA_CONTROL_REG			0x0
+#define MVPP22_FCA_ENABLE_PERIODIC		BIT(11)
+#define MVPP22_PERIODIC_COUNTER_LSB_REG		(0x110)
+#define MVPP22_PERIODIC_COUNTER_MSB_REG		(0x114)
+
 /* XPCS registers. PPv2.2 and PPv2.3 */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0
@@ -752,7 +761,9 @@
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
 /* MSS Flow control */
-#define MSS_SRAM_SIZE	0x800
+#define MSS_SRAM_SIZE		0x800
+#define FC_QUANTA		0xFFFF
+#define FC_CLK_DIVIDER		100
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 409ca64..8f40293a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1291,6 +1291,49 @@ static void mvpp22_gop_init_10gkr(struct mvpp2_port *port)
 	writel(val, mpcs + MVPP22_MPCS_CLK_RESET);
 }
 
+static void mvpp22_gop_fca_enable_periodic(struct mvpp2_port *port, bool en)
+{
+	struct mvpp2 *priv = port->priv;
+	void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+	u32 val;
+
+	val = readl(fca + MVPP22_FCA_CONTROL_REG);
+	val &= ~MVPP22_FCA_ENABLE_PERIODIC;
+	if (en)
+		val |= MVPP22_FCA_ENABLE_PERIODIC;
+	writel(val, fca + MVPP22_FCA_CONTROL_REG);
+}
+
+static void mvpp22_gop_fca_set_timer(struct mvpp2_port *port, u32 timer)
+{
+	struct mvpp2 *priv = port->priv;
+	void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+	u32 lsb, msb;
+
+	lsb = timer & MVPP22_FCA_REG_MASK;
+	msb = timer >> MVPP22_FCA_REG_SIZE;
+
+	writel(lsb, fca + MVPP22_PERIODIC_COUNTER_LSB_REG);
+	writel(msb, fca + MVPP22_PERIODIC_COUNTER_MSB_REG);
+}
+
+/* Set Flow Control timer x100 faster than pause quanta to ensure that link
+ * partner won't send traffic if port is in XOFF mode.
+ */
+static void mvpp22_gop_fca_set_periodic_timer(struct mvpp2_port *port)
+{
+	u32 timer;
+
+	timer = (port->priv->tclk / (USEC_PER_SEC * FC_CLK_DIVIDER))
+		* FC_QUANTA;
+
+	mvpp22_gop_fca_enable_periodic(port, false);
+
+	mvpp22_gop_fca_set_timer(port, timer);
+
+	mvpp22_gop_fca_enable_periodic(port, true);
+}
+
 static int mvpp22_gop_init(struct mvpp2_port *port)
 {
 	struct mvpp2 *priv = port->priv;
@@ -1335,6 +1378,8 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
 	val |= GENCONF_SOFT_RESET1_GOP;
 	regmap_write(priv->sysctrl_base, GENCONF_SOFT_RESET1, val);
 
+	mvpp22_gop_fca_set_periodic_timer(port);
+
 unsupported_conf:
 	return 0;
 
-- 
1.9.1

[PATCH v4 net-next 10/19] net: mvpp2: add FCA RXQ non occupied descriptor threshold

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

RXQ non occupied descriptor threshold would be used by
Flow Control Firmware feature to move to the XOFF mode.
RXQ non occupied threshold would change interrupt cause
that polled by CM3 Firmware.
Actual non occupied interrupt masked and won't trigger interrupt.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  3 ++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 46 +++++++++++++++++---
 2 files changed, 42 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 73f087c..9d8993f 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -295,6 +295,8 @@
 #define     MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK	0x3fc00000
 #define     MVPP2_PON_CAUSE_MISC_SUM_MASK		BIT(31)
 #define MVPP2_ISR_MISC_CAUSE_REG		0x55b0
+#define MVPP2_ISR_RX_ERR_CAUSE_REG(port)	(0x5520 + 4 * (port))
+#define	    MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK	0x00ff
 
 /* Buffer Manager registers */
 #define MVPP2_BM_POOL_BASE_REG(pool)		(0x6000 + ((pool) * 4))
@@ -764,6 +766,7 @@
 #define MSS_SRAM_SIZE		0x800
 #define FC_QUANTA		0xFFFF
 #define FC_CLK_DIVIDER		100
+#define MSS_THRESHOLD_STOP	768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 8f40293a..a4933c4 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1144,14 +1144,19 @@ static inline void mvpp2_qvec_interrupt_disable(struct mvpp2_queue_vector *qvec)
 static void mvpp2_interrupts_mask(void *arg)
 {
 	struct mvpp2_port *port = arg;
+	int cpu = smp_processor_id();
+	u32 thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu >= port->priv->nthreads)
 		return;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), 0);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id), 0);
 }
 
 /* Unmask the current thread's Rx/Tx interrupts.
@@ -1161,20 +1166,25 @@ static void mvpp2_interrupts_mask(void *arg)
 static void mvpp2_interrupts_unmask(void *arg)
 {
 	struct mvpp2_port *port = arg;
-	u32 val;
+	int cpu = smp_processor_id();
+	u32 val, thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu >= port->priv->nthreads)
 		return;
 
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
 	val = MVPP2_CAUSE_MISC_SUM_MASK |
 		MVPP2_CAUSE_RXQ_OCCUP_DESC_ALL_MASK(port->priv->hw_version);
 	if (port->has_tx_irqs)
 		val |= MVPP2_CAUSE_TXQ_OCCUP_DESC_ALL_MASK;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+			   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 }
 
 static void
@@ -1199,6 +1209,9 @@ static void mvpp2_interrupts_unmask(void *arg)
 
 		mvpp2_thread_write(port->priv, v->sw_thread_id,
 				   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+		mvpp2_thread_write(port->priv, v->sw_thread_id,
+				   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+				   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 	}
 }
 
@@ -2404,6 +2417,22 @@ static void mvpp2_txp_max_tx_size_set(struct mvpp2_port *port)
 	}
 }
 
+/* Routine set the number of non-occupied descriptors threshold that change
+ * interrupt error cause polled by FW Flow Control
+ */
+static void mvpp2_set_rxq_free_tresh(struct mvpp2_port *port,
+				     struct mvpp2_rx_queue *rxq)
+{
+	u32 val;
+
+	mvpp2_write(port->priv, MVPP2_RXQ_NUM_REG, rxq->id);
+
+	val = mvpp2_read(port->priv, MVPP2_RXQ_THRESH_REG);
+	val &= ~MVPP2_RXQ_NON_OCCUPIED_MASK;
+	val |= MSS_THRESHOLD_STOP << MVPP2_RXQ_NON_OCCUPIED_OFFSET;
+	mvpp2_write(port->priv, MVPP2_RXQ_THRESH_REG, val);
+}
+
 /* Set the number of packets that will be received before Rx interrupt
  * will be generated by HW.
  */
@@ -2659,6 +2688,9 @@ static int mvpp2_rxq_init(struct mvpp2_port *port,
 	mvpp2_rx_pkts_coal_set(port, rxq);
 	mvpp2_rx_time_coal_set(port, rxq);
 
+	/* Set the number of non occupied descriptors threshold */
+	mvpp2_set_rxq_free_tresh(port, rxq);
+
 	/* Add number of descriptors ready for receiving packets */
 	mvpp2_rxq_status_update(port, rxq->id, 0, rxq->size);
 
-- 
1.9.1

[PATCH v4 net-next 11/19] net: mvpp2: add spinlock for FW FCA configuration path

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Spinlock added to MSS shared memory configuration space.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 5 +++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 3 +++
 2 files changed, 8 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9d8993f..f34e260 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -1021,6 +1021,11 @@ struct mvpp2 {
 
 	/* CM3 SRAM pool */
 	struct gen_pool *sram_pool;
+
+	bool custom_dma_mask;
+
+	/* Spinlocks for CM3 shared memory configuration */
+	spinlock_t mss_spinlock;
 };
 
 struct mvpp2_pcpu_stats {
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index a4933c4..64534f0 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -7163,6 +7163,9 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->hw_version = MVPP23;
 	}
 
+	/* Init mss lock */
+	spin_lock_init(&priv->mss_spinlock);
+
 	/* Initialize network controller */
 	err = mvpp2_init(pdev, priv);
 	if (err < 0) {
-- 
1.9.1

[PATCH v4 net-next 12/19] net: mvpp2: enable global flow control

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch enables global flow control in FW and in the phylink validate mask.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  3 +++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 20 +++++++++++++++++++-
 2 files changed, 22 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index f34e260..e9625fb 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -1022,6 +1022,9 @@ struct mvpp2 {
 	/* CM3 SRAM pool */
 	struct gen_pool *sram_pool;
 
+	/* Global TX Flow Control config */
+	bool global_tx_fc;
+
 	bool custom_dma_mask;
 
 	/* Spinlocks for CM3 shared memory configuration */
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 64534f0..4d55344 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -5963,6 +5963,11 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
 	phylink_set(mask, Autoneg);
 	phylink_set_port_modes(mask);
 
+	if (port->priv->global_tx_fc) {
+		phylink_set(mask, Pause);
+		phylink_set(mask, Asym_Pause);
+	}
+
 	switch (state->interface) {
 	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XAUI:
@@ -6981,7 +6986,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err;
+	int err, val;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -7035,6 +7040,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 			return err;
 		else if (err)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
+
+		/* Enable global Flow Control only if handler to SRAM not NULL */
+		if (priv->cm3_base)
+			priv->global_tx_fc = true;
 	}
 
 	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
@@ -7205,6 +7214,15 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+		val |= FLOW_CONTROL_ENABLE_BIT;
+		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+	}
+
 	mvpp2_dbgfs_init(priv, pdev->name);
 
 	platform_set_drvdata(pdev, priv);
-- 
1.9.1

[PATCH v4 net-next 13/19] net: mvpp2: add RXQ flow control configurations

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch add RXQ flow control configurations.
Patch do not enable flow control itself, flow control
disabled by default.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  38 ++++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 111 ++++++++++++++++++++
 2 files changed, 146 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index e9625fb..934d535 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -763,10 +763,39 @@
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
 /* MSS Flow control */
-#define MSS_SRAM_SIZE		0x800
-#define FC_QUANTA		0xFFFF
-#define FC_CLK_DIVIDER		100
+#define MSS_SRAM_SIZE			0x800
+#define MSS_FC_COM_REG			0
+#define FLOW_CONTROL_ENABLE_BIT		BIT(0)
+#define FLOW_CONTROL_UPDATE_COMMAND_BIT	BIT(31)
+#define FC_QUANTA			0xFFFF
+#define FC_CLK_DIVIDER			100
+
+#define MSS_RXQ_TRESH_BASE		0x200
+#define MSS_RXQ_TRESH_OFFS		4
+#define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
+					* MSS_RXQ_TRESH_OFFS))
+
+#define MSS_RXQ_TRESH_START_MASK	0xFFFF
+#define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
+#define MSS_RXQ_TRESH_STOP_OFFS		16
+
+#define MSS_RXQ_ASS_BASE	0x80
+#define MSS_RXQ_ASS_OFFS	4
+#define MSS_RXQ_ASS_PER_REG	4
+#define MSS_RXQ_ASS_PER_OFFS	8
+#define MSS_RXQ_ASS_PORTID_OFFS	0
+#define MSS_RXQ_ASS_PORTID_MASK	0x3
+#define MSS_RXQ_ASS_HOSTID_OFFS	2
+#define MSS_RXQ_ASS_HOSTID_MASK	0x3F
+
+#define MSS_RXQ_ASS_Q_BASE(q, fq) ((((q) + (fq)) % MSS_RXQ_ASS_PER_REG)	 \
+				  * MSS_RXQ_ASS_PER_OFFS)
+#define MSS_RXQ_ASS_PQ_BASE(q, fq) ((((q) + (fq)) / MSS_RXQ_ASS_PER_REG) \
+				   * MSS_RXQ_ASS_OFFS)
+#define MSS_RXQ_ASS_REG(q, fq) (MSS_RXQ_ASS_BASE + MSS_RXQ_ASS_PQ_BASE(q, fq))
+
 #define MSS_THRESHOLD_STOP	768
+#define MSS_THRESHOLD_START	1024
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
@@ -1191,6 +1220,9 @@ struct mvpp2_port {
 	bool rx_hwtstamp;
 	enum hwtstamp_tx_types tx_hwtstamp_type;
 	struct mvpp2_hwtstamp_queue tx_hwtstamp_queue[2];
+
+	/* Firmware TX flow control */
+	bool tx_fc;
 };
 
 /* The mvpp2_tx_desc and mvpp2_rx_desc structures describe the
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 4d55344..36e33d5 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -742,6 +742,110 @@ static void *mvpp2_buf_alloc(struct mvpp2_port *port,
 	return data;
 }
 
+/* Routine enable flow control for RXQs condition */
+static void mvpp2_rxq_enable_fc(struct mvpp2_port *port)
+{
+	int val, cm3_state, host_id, q;
+	int fq = port->first_rxq;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Set same Flow control for all RXQs */
+	for (q = 0; q < port->nrxqs; q++) {
+		/* Set stop and start Flow control RXQ thresholds */
+		val = MSS_THRESHOLD_START;
+		val |= (MSS_THRESHOLD_STOP << MSS_RXQ_TRESH_STOP_OFFS);
+		mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+		val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+		/* Set RXQ port ID */
+		val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+		val |= (port->id << MSS_RXQ_ASS_Q_BASE(q, fq));
+		val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		/* Calculate RXQ host ID:
+		 * In Single queue mode: Host ID equal to Host ID used for
+		 *			 shared RX interrupt
+		 * In Multi queue mode: Host ID equal to number of
+		 *			RXQ ID / number of CoS queues
+		 * In Single resource mode: Host ID always equal to 0
+		 */
+		if (queue_mode == MVPP2_QDIST_SINGLE_MODE)
+			host_id = port->nqvecs;
+		else if (queue_mode == MVPP2_QDIST_MULTI_MODE)
+			host_id = q;
+		else
+			host_id = 0;
+
+		/* Set RXQ host ID */
+		val |= (host_id << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
+/* Routine disable flow control for RXQs condition */
+static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
+{
+	int val, cm3_state, q;
+	unsigned long flags;
+	int fq = port->first_rxq;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Disable Flow control for all RXQs */
+	for (q = 0; q < port->nrxqs; q++) {
+		/* Set threshold 0 to disable Flow control */
+		val = 0;
+		val |= (0 << MSS_RXQ_TRESH_STOP_OFFS);
+		mvpp2_cm3_write(port->priv, MSS_RXQ_TRESH_REG(q, fq), val);
+
+		val = mvpp2_cm3_read(port->priv, MSS_RXQ_ASS_REG(q, fq));
+
+		val &= ~(MSS_RXQ_ASS_PORTID_MASK << MSS_RXQ_ASS_Q_BASE(q, fq));
+
+		val &= ~(MSS_RXQ_ASS_HOSTID_MASK << (MSS_RXQ_ASS_Q_BASE(q, fq)
+			+ MSS_RXQ_ASS_HOSTID_OFFS));
+
+		mvpp2_cm3_write(port->priv, MSS_RXQ_ASS_REG(q, fq), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -3008,6 +3112,9 @@ static void mvpp2_cleanup_rxqs(struct mvpp2_port *port)
 
 	for (queue = 0; queue < port->nrxqs; queue++)
 		mvpp2_rxq_deinit(port, port->rxqs[queue]);
+
+	if (port->tx_fc)
+		mvpp2_rxq_disable_fc(port);
 }
 
 /* Init all Rx queues for port */
@@ -3020,6 +3127,10 @@ static int mvpp2_setup_rxqs(struct mvpp2_port *port)
 		if (err)
 			goto err_cleanup;
 	}
+
+	if (port->tx_fc)
+		mvpp2_rxq_enable_fc(port);
+
 	return 0;
 
 err_cleanup:
-- 
1.9.1

[PATCH v4 net-next 14/19] net: mvpp2: add ethtool flow control configuration support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch add ethtool flow control configuration support.

Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.

Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 +++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 98 ++++++++++++++++++++
 2 files changed, 111 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 934d535..1d0d8f2 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -775,6 +775,19 @@
 #define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
 					* MSS_RXQ_TRESH_OFFS))
 
+#define MSS_BUF_POOL_BASE		0x40
+#define MSS_BUF_POOL_OFFS		4
+#define MSS_BUF_POOL_REG(id)		(MSS_BUF_POOL_BASE		\
+					+ (id) * MSS_BUF_POOL_OFFS)
+
+#define MSS_BUF_POOL_STOP_MASK		0xFFF
+#define MSS_BUF_POOL_START_MASK		(0xFFF << MSS_BUF_POOL_START_OFFS)
+#define MSS_BUF_POOL_START_OFFS		12
+#define MSS_BUF_POOL_PORTS_MASK		(0xF << MSS_BUF_POOL_PORTS_OFFS)
+#define MSS_BUF_POOL_PORTS_OFFS		24
+#define MSS_BUF_POOL_PORT_OFFS(id)	(0x1 <<				\
+					((id) + MSS_BUF_POOL_PORTS_OFFS))
+
 #define MSS_RXQ_TRESH_START_MASK	0xFFFF
 #define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
 #define MSS_RXQ_TRESH_STOP_OFFS		16
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 36e33d5..eab7d12 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -846,6 +846,59 @@ static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+/* Routine disable/enable flow control for BM pool condition */
+static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
+				    struct mvpp2_bm_pool *pool,
+				    bool en)
+{
+	int val, cm3_state;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Check if BM pool should be enabled/disable */
+	if (en) {
+		/* Set BM pool start and stop thresholds per port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val |= MSS_BUF_POOL_PORT_OFFS(port->id);
+		val &= ~MSS_BUF_POOL_START_MASK;
+		val |= (MSS_THRESHOLD_START << MSS_BUF_POOL_START_OFFS);
+		val &= ~MSS_BUF_POOL_STOP_MASK;
+		val |= MSS_THRESHOLD_STOP;
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	} else {
+		/* Remove BM pool from the port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val &= ~MSS_BUF_POOL_PORT_OFFS(port->id);
+
+		/* Zero BM pool start and stop thresholds to disable pool
+		 * flow control if pool empty (not used by any port)
+		 */
+		if (!pool->buf_num) {
+			val &= ~MSS_BUF_POOL_START_MASK;
+			val &= ~MSS_BUF_POOL_STOP_MASK;
+		}
+
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -1176,6 +1229,16 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		new_long_pool = MVPP2_BM_LONG;
 
 	if (new_long_pool != port->pool_long->id) {
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port,
+							port->pool_short,
+							false);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							false);
+		}
+
 		/* Remove port from old short & long pool */
 		port->pool_long = mvpp2_bm_pool_use(port, port->pool_long->id,
 						    port->pool_long->pkt_size);
@@ -1193,6 +1256,25 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		mvpp2_swf_bm_pool_init(port);
 
 		mvpp2_set_hw_csum(port, new_long_pool);
+
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							true);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_short,
+							true);
+		}
+
+		/* Update L4 checksum when jumbo enable/disable on port */
+		if (new_long_pool == MVPP2_BM_JUMBO && port->id != 0) {
+			dev->features &= ~(NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM);
+			dev->hw_features &= ~(NETIF_F_IP_CSUM |
+					      NETIF_F_IPV6_CSUM);
+		} else {
+			dev->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+			dev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+		}
 	}
 
 out_set:
@@ -6358,6 +6440,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 	u32 val;
+	int i;
 
 	if (mvpp2_is_xlg(interface)) {
 		if (!phylink_autoneg_inband(mode)) {
@@ -6408,6 +6491,21 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
+	if (port->priv->global_tx_fc) {
+		port->tx_fc = tx_pause;
+		if (tx_pause)
+			mvpp2_rxq_enable_fc(port);
+		else
+			mvpp2_rxq_disable_fc(port);
+		if (port->priv->percpu_pools) {
+			for (i = 0; i < port->nrxqs; i++)
+				mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[i], tx_pause);
+		} else {
+			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
+			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
+		}
+	}
+
 	mvpp2_port_enable(port);
 
 	mvpp2_egress_enable(port);
-- 
1.9.1

[PATCH v4 net-next 15/19] net: mvpp2: add BM protection underrun feature support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Feature double size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  8 +++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 35 +++++++++++++++++++-
 2 files changed, 42 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 1d0d8f2..798be58 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -324,6 +324,10 @@
 #define     MVPP2_BM_HIGH_THRESH_MASK		0x7f0000
 #define     MVPP2_BM_HIGH_THRESH_VALUE(val)	((val) << \
 						MVPP2_BM_HIGH_THRESH_OFFS)
+#define     MVPP2_BM_BPPI_HIGH_THRESH		0x1E
+#define     MVPP2_BM_BPPI_LOW_THRESH		0x1C
+#define     MVPP23_BM_BPPI_HIGH_THRESH		0x34
+#define     MVPP23_BM_BPPI_LOW_THRESH		0x28
 #define MVPP2_BM_INTR_CAUSE_REG(pool)		(0x6240 + ((pool) * 4))
 #define     MVPP2_BM_RELEASED_DELAY_MASK	BIT(0)
 #define     MVPP2_BM_ALLOC_FAILED_MASK		BIT(1)
@@ -352,6 +356,10 @@
 #define MVPP2_OVERRUN_ETH_DROP			0x7000
 #define MVPP2_CLS_ETH_DROP			0x7020
 
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG	0x6310
+#define     MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK	0xff
+#define     MVPP23_BM_8POOL_MODE		BIT(8)
+
 /* Hit counters registers */
 #define MVPP2_CTRS_IDX				0x7040
 #define     MVPP22_CTRS_TX_CTR(port, txq)	((txq) | ((port) << 3) | BIT(7))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index eab7d12..6f43881 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -70,6 +70,11 @@ enum mvpp2_bm_pool_log_num {
 module_param(queue_mode, int, 0444);
 MODULE_PARM_DESC(queue_mode, "Set queue_mode (single=0, multi=1)");
 
+static int bm_underrun_protect = 1;
+
+module_param(bm_underrun_protect, int, 0444);
+MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");
+
 /* Utility/helper methods */
 
 void mvpp2_write(struct mvpp2 *priv, u32 offset, u32 data)
@@ -424,6 +429,21 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 
 	val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
 	val |= MVPP2_BM_START_MASK;
+
+	val &= ~MVPP2_BM_LOW_THRESH_MASK;
+	val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+	/* Set 8 Pools BPPI threshold if BM underrun protection feature
+	 * were enabled
+	 */
+	if (priv->hw_version == MVPP23 && bm_underrun_protect) {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+	} else {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+	}
+
 	mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
 
 	bm_pool->size = size;
@@ -592,6 +612,16 @@ static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
 	return err;
 }
 
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+	val |= MVPP23_BM_8POOL_MODE;
+	mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
 static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 {
 	enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
@@ -645,6 +675,9 @@ static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 	if (!priv->bm_pools)
 		return -ENOMEM;
 
+	if (priv->hw_version == MVPP23 && bm_underrun_protect)
+		mvpp23_bm_set_8pool_mode(priv);
+
 	err = mvpp2_bm_pools_init(dev, priv);
 	if (err < 0)
 		return err;
@@ -6491,7 +6524,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
-	if (port->priv->global_tx_fc) {
+	if (port->priv->global_tx_fc && bm_underrun_protect) {
 		port->tx_fc = tx_pause;
 		if (tx_pause)
 			mvpp2_rxq_enable_fc(port);
-- 
1.9.1

[PATCH v4 net-next 16/19] net: mvpp2: add PPv23 RX FIFO flow control

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

New FIFO flow control feature were added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current  FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 15 ++++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 53 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 798be58..0765d6f 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -770,6 +770,18 @@
 #define MVPP2_TX_FIFO_THRESHOLD(kb)	\
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
+/* RX FIFO threshold in 1KB granularity */
+#define MVPP23_PORT0_FIFO_TRSH	(9 * 1024)
+#define MVPP23_PORT1_FIFO_TRSH	(4 * 1024)
+#define MVPP23_PORT2_FIFO_TRSH	(2 * 1024)
+
+/* RX Flow Control Registers */
+#define MVPP2_RX_FC_REG(port)		(0x150 + 4 * (port))
+#define     MVPP2_RX_FC_EN		BIT(24)
+#define     MVPP2_RX_FC_TRSH_OFFS	16
+#define     MVPP2_RX_FC_TRSH_MASK	(0xFF << MVPP2_RX_FC_TRSH_OFFS)
+#define     MVPP2_RX_FC_TRSH_UNIT	256
+
 /* MSS Flow control */
 #define MSS_SRAM_SIZE			0x800
 #define MSS_FC_COM_REG			0
@@ -1504,6 +1516,8 @@ struct mvpp2_bm_pool {
 
 void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
 
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en);
+
 #ifdef CONFIG_MVPP2_PTP
 int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv);
 void mvpp22_tai_tstamp(struct mvpp2_tai *tai, u32 tstamp,
@@ -1536,4 +1550,5 @@ static inline bool mvpp22_rx_hwtstamping(struct mvpp2_port *port)
 {
 	return IS_ENABLED(CONFIG_MVPP2_PTP) && port->rx_hwtstamp;
 }
+
 #endif
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 6f43881..15974a7 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6537,6 +6537,8 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
 			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
 		}
+		if (port->priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_en(port->priv, port->id, tx_pause);
 	}
 
 	mvpp2_port_enable(port);
@@ -7005,6 +7007,55 @@ static void mvpp22_rx_fifo_init(struct mvpp2 *priv)
 	mvpp2_write(priv, MVPP2_RX_FIFO_INIT_REG, 0x1);
 }
 
+/* Configure Rx FIFO Flow control thresholds */
+static void mvpp23_rx_fifo_fc_set_tresh(struct mvpp2 *priv)
+{
+	int port, val;
+
+	/* Port 0: maximum speed -10Gb/s port
+	 *	   required by spec RX FIFO threshold 9KB
+	 * Port 1: maximum speed -5Gb/s port
+	 *	   required by spec RX FIFO threshold 4KB
+	 * Port 2: maximum speed -1Gb/s port
+	 *	   required by spec RX FIFO threshold 2KB
+	 */
+
+	/* Without loopback port */
+	for (port = 0; port < (MVPP2_MAX_PORTS - 1); port++) {
+		if (port == 0) {
+			val = (MVPP23_PORT0_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else if (port == 1) {
+			val = (MVPP23_PORT1_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else {
+			val = (MVPP23_PORT2_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		}
+	}
+}
+
+/* Configure Rx FIFO Flow control thresholds */
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP2_RX_FC_REG(port));
+
+	if (en)
+		val |= MVPP2_RX_FC_EN;
+	else
+		val &= ~MVPP2_RX_FC_EN;
+
+	mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+}
+
 static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
 {
 	int threshold = MVPP2_TX_FIFO_THRESHOLD(size);
@@ -7156,6 +7207,8 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	} else {
 		mvpp22_rx_fifo_init(priv);
 		mvpp22_tx_fifo_init(priv);
+		if (priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_set_tresh(priv);
 	}
 
 	if (priv->hw_version == MVPP21)
-- 
1.9.1

[PATCH v4 net-next 17/19] net: mvpp2: set 802.3x GoP Flow Control mode

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 15974a7..55138c7 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6284,7 +6284,7 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 	old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
 
 	ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
-	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
+	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK | MVPP2_GMAC_FLOW_CTRL_MASK);
 
 	/* Configure port type */
 	if (phy_interface_mode_is_8023z(state->interface)) {
-- 
1.9.1

[PATCH v4 net-next 18/19] net: mvpp2: limit minimum ring size to 1024 descriptors

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

To support Flow Control ring size should be at least 1024 descriptors.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 55138c7..bb7dfed 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -4545,6 +4545,8 @@ static int mvpp2_check_ringparam_valid(struct net_device *dev,
 
 	if (ring->rx_pending > MVPP2_MAX_RXD_MAX)
 		new_rx_pending = MVPP2_MAX_RXD_MAX;
+	else if (ring->rx_pending < MSS_THRESHOLD_START)
+		new_rx_pending = MSS_THRESHOLD_START;
 	else if (!IS_ALIGNED(ring->rx_pending, 16))
 		new_rx_pending = ALIGN(ring->rx_pending, 16);
 
-- 
1.9.1

[PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  1 +
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 41 ++++++++++++++++----
 2 files changed, 35 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 0765d6f..47a4b38 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -829,6 +829,7 @@
 
 #define MSS_THRESHOLD_STOP	768
 #define MSS_THRESHOLD_START	1024
+#define MSS_FC_MAX_TIMEOUT	5000
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index bb7dfed..3aa877b 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -932,6 +932,34 @@ static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+static int mvpp2_enable_global_fc(struct mvpp2 *priv)
+{
+	int val, timeout = 0;
+
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	/* Check if Firmware running and disable FC if not*/
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	while (timeout < MSS_FC_MAX_TIMEOUT) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+
+		if (!(val & FLOW_CONTROL_UPDATE_COMMAND_BIT))
+			return 0;
+		usleep_range(10, 20);
+		timeout++;
+	}
+
+	priv->global_tx_fc = false;
+	return -EOPNOTSUPP;
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -7283,7 +7311,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err, val;
+	int err;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -7511,13 +7539,12 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
-	/* Enable global flow control. In this stage global
-	 * flow control enabled, but still disabled per port.
-	 */
 	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
-		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
-		val |= FLOW_CONTROL_ENABLE_BIT;
-		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+		err = mvpp2_enable_global_fc(priv);
+		if (err) {
+			dev_warn(&pdev->dev, "CM3 firmware not running, version should be higher than 18.09\n");
+			dev_warn(&pdev->dev, "Flow control not supported\n");
+		}
 	}
 
 	mvpp2_dbgfs_init(priv, pdev->name);
-- 
1.9.1

Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[Russell King - ARM Linux admin]

On Wed, Jan 27, 2021 at 01:43:35PM +0200, stefanc@marvell.com wrote:
>  	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
> -		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
> -		val |= FLOW_CONTROL_ENABLE_BIT;
> -		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
> +		err = mvpp2_enable_global_fc(priv);
> +		if (err) {
> +			dev_warn(&pdev->dev, "CM3 firmware not running, version should be higher than 18.09\n");
> +			dev_warn(&pdev->dev, "Flow control not supported\n");
> +		}

I've just booted this on my mcbin-ss, and I get:

mvpp2 f2000000.ethernet: CM3 firmware not running, version should be higher than 18.09
mvpp2 f4000000.ethernet: CM3 firmware not running, version should be higher than 18.09

which is rather odd, because I believe I'm running the 18.12 firmware
from git://github.com/MarvellEmbeddedProcessors/binaries-marvell
branch binaries-marvell-armada-18.12.

Any ideas?

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

RE: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[Stefan Chulski]

> -----Original Message-----
> From: Russell King - ARM Linux admin <linux@armlinux.org.uk>
> Sent: Wednesday, January 27, 2021 4:06 PM
> To: Stefan Chulski <stefanc@marvell.com>
> Cc: netdev@vger.kernel.org; thomas.petazzoni@bootlin.com;
> davem@davemloft.net; Nadav Haklai <nadavh@marvell.com>; Yan
> Markman <ymarkman@marvell.com>; linux-kernel@vger.kernel.org;
> kuba@kernel.org; mw@semihalf.com; andrew@lunn.ch;
> atenart@kernel.org
> Subject: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC
> firmware check
> 
> External Email
> 
> ----------------------------------------------------------------------
> On Wed, Jan 27, 2021 at 01:43:35PM +0200, stefanc@marvell.com wrote:
> >  	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
> > -		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
> > -		val |= FLOW_CONTROL_ENABLE_BIT;
> > -		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
> > +		err = mvpp2_enable_global_fc(priv);
> > +		if (err) {
> > +			dev_warn(&pdev->dev, "CM3 firmware not running,
> version should be higher than 18.09\n");
> > +			dev_warn(&pdev->dev, "Flow control not
> supported\n");
> > +		}
> 
> I've just booted this on my mcbin-ss, and I get:
> 
> mvpp2 f2000000.ethernet: CM3 firmware not running, version should be
> higher than 18.09
> mvpp2 f4000000.ethernet: CM3 firmware not running, version should be
> higher than 18.09
> 
> which is rather odd, because I believe I'm running the 18.12 firmware from
> git://github.com/MarvellEmbeddedProcessors/binaries-marvell
> branch binaries-marvell-armada-18.12.
> 
> Any ideas?

Your mcbin-ss is A8K AX or A8K B0? On AX revisions we do not have FC support in firmware.

Regards.

Re: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[Russell King - ARM Linux admin]

On Wed, Jan 27, 2021 at 02:37:34PM +0000, Stefan Chulski wrote:
> Your mcbin-ss is A8K AX or A8K B0? On AX revisions we do not have FC support in firmware.

How do I tell? I don't want to remove the heatsink, and I don't see
anything in MV-S111188-00E. I didn't grab a copy of the Errata before
I accidentally let me extranet access expire.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

RE: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[Stefan Chulski]

> -----Original Message-----
> From: Russell King - ARM Linux admin <linux@armlinux.org.uk>
> Sent: Wednesday, January 27, 2021 5:00 PM
> To: Stefan Chulski <stefanc@marvell.com>
> Cc: netdev@vger.kernel.org; thomas.petazzoni@bootlin.com;
> davem@davemloft.net; Nadav Haklai <nadavh@marvell.com>; Yan
> Markman <ymarkman@marvell.com>; linux-kernel@vger.kernel.org;
> kuba@kernel.org; mw@semihalf.com; andrew@lunn.ch;
> atenart@kernel.org
> Subject: Re: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC
> firmware check
> 
> On Wed, Jan 27, 2021 at 02:37:34PM +0000, Stefan Chulski wrote:
> > Your mcbin-ss is A8K AX or A8K B0? On AX revisions we do not have FC
> support in firmware.
> 
> How do I tell? I don't want to remove the heatsink, and I don't see anything
> in MV-S111188-00E. I didn't grab a copy of the Errata before I accidentally let
> me extranet access expire.

You can devmem 0xF2400240(Device ID Status Register).
#define A8040_B0_DEVICE_ID      0x8045
#define A8040_AX_DEVICE_ID      0x8040
#define A7040_B0_DEVICE_ID      0x7045
#define A7040_AX_DEVICE_ID      0x7040
#define A3900_A1_DEVICE_ID      0x6025
#define CN9130_DEVICE_ID        0x7025

Regards.

Re: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[Russell King - ARM Linux admin]

On Wed, Jan 27, 2021 at 03:10:11PM +0000, Stefan Chulski wrote:
> You can devmem 0xF2400240(Device ID Status Register).
> #define A8040_B0_DEVICE_ID      0x8045
> #define A8040_AX_DEVICE_ID      0x8040
> #define A7040_B0_DEVICE_ID      0x7045
> #define A7040_AX_DEVICE_ID      0x7040
> #define A3900_A1_DEVICE_ID      0x6025
> #define CN9130_DEVICE_ID        0x7025

Thanks. 0x00028040, so it's AX silicon. Is there nothing that can be
done for flow control on that?

It would probably also be a good idea to state this requirement in the
message as well, rather than just suggesting the firmware revision.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

RE: [EXT] Re: [PATCH v4 net-next 19/19] net: mvpp2: add TX FC firmware check

[Stefan Chulski]

> > You can devmem 0xF2400240(Device ID Status Register).
> > #define A8040_B0_DEVICE_ID      0x8045
> > #define A8040_AX_DEVICE_ID      0x8040
> > #define A7040_B0_DEVICE_ID      0x7045
> > #define A7040_AX_DEVICE_ID      0x7040
> > #define A3900_A1_DEVICE_ID      0x6025
> > #define CN9130_DEVICE_ID        0x7025
> 
> Thanks. 0x00028040, so it's AX silicon. Is there nothing that can be done for
> flow control on that?

No, we cannot support FC with AX on A8040.
 
> It would probably also be a good idea to state this requirement in the
> message as well, rather than just suggesting the firmware revision.

Ok, I would update this.

Thanks,
Stefan.

Re: [PATCH v4 net-next 10/19] net: mvpp2: add FCA RXQ non occupied descriptor threshold

[Willem de Bruijn]

On Wed, Jan 27, 2021 at 7:26 AM <stefanc@marvell.com> wrote:
>
> From: Stefan Chulski <stefanc@marvell.com>
>
> RXQ non occupied descriptor threshold would be used by
> Flow Control Firmware feature to move to the XOFF mode.
> RXQ non occupied threshold would change interrupt cause
> that polled by CM3 Firmware.
> Actual non occupied interrupt masked and won't trigger interrupt.

Does this mean that this change enables a feature, but it is unused
due to a masked interrupt?

>
> Signed-off-by: Stefan Chulski <stefanc@marvell.com>
> ---
>  drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  3 ++
>  drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 46 +++++++++++++++++---
>  2 files changed, 42 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> index 73f087c..9d8993f 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> @@ -295,6 +295,8 @@
>  #define     MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK    0x3fc00000
>  #define     MVPP2_PON_CAUSE_MISC_SUM_MASK              BIT(31)
>  #define MVPP2_ISR_MISC_CAUSE_REG               0x55b0
> +#define MVPP2_ISR_RX_ERR_CAUSE_REG(port)       (0x5520 + 4 * (port))
> +#define            MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK  0x00ff

The indentation in this file is inconsistent. Here even between the
two newly introduced lines.

>  /* Buffer Manager registers */
>  #define MVPP2_BM_POOL_BASE_REG(pool)           (0x6000 + ((pool) * 4))
> @@ -764,6 +766,7 @@
>  #define MSS_SRAM_SIZE          0x800
>  #define FC_QUANTA              0xFFFF
>  #define FC_CLK_DIVIDER         100
> +#define MSS_THRESHOLD_STOP     768
>
>  /* RX buffer constants */
>  #define MVPP2_SKB_SHINFO_SIZE \
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> index 8f40293a..a4933c4 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
> @@ -1144,14 +1144,19 @@ static inline void mvpp2_qvec_interrupt_disable(struct mvpp2_queue_vector *qvec)
>  static void mvpp2_interrupts_mask(void *arg)
>  {
>         struct mvpp2_port *port = arg;
> +       int cpu = smp_processor_id();
> +       u32 thread;
>
>         /* If the thread isn't used, don't do anything */
> -       if (smp_processor_id() > port->priv->nthreads)
> +       if (cpu >= port->priv->nthreads)
>                 return;

Here and below, the change from greater than to greater than is really
a (standalone) fix?

> -       mvpp2_thread_write(port->priv,
> -                          mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
> +       thread = mvpp2_cpu_to_thread(port->priv, cpu);
> +
> +       mvpp2_thread_write(port->priv, thread,
>                            MVPP2_ISR_RX_TX_MASK_REG(port->id), 0);
> +       mvpp2_thread_write(port->priv, thread,
> +                          MVPP2_ISR_RX_ERR_CAUSE_REG(port->id), 0);
>  }
>
>  /* Unmask the current thread's Rx/Tx interrupts.
> @@ -1161,20 +1166,25 @@ static void mvpp2_interrupts_mask(void *arg)
>  static void mvpp2_interrupts_unmask(void *arg)
>  {
>         struct mvpp2_port *port = arg;
> -       u32 val;
> +       int cpu = smp_processor_id();
> +       u32 val, thread;
>
>         /* If the thread isn't used, don't do anything */
> -       if (smp_processor_id() > port->priv->nthreads)
> +       if (cpu >= port->priv->nthreads)
>                 return;
>
> +       thread = mvpp2_cpu_to_thread(port->priv, cpu);
> +
>         val = MVPP2_CAUSE_MISC_SUM_MASK |
>                 MVPP2_CAUSE_RXQ_OCCUP_DESC_ALL_MASK(port->priv->hw_version);
>         if (port->has_tx_irqs)
>                 val |= MVPP2_CAUSE_TXQ_OCCUP_DESC_ALL_MASK;
>
> -       mvpp2_thread_write(port->priv,
> -                          mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
> +       mvpp2_thread_write(port->priv, thread,
>                            MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
> +       mvpp2_thread_write(port->priv, thread,
> +                          MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
> +                          MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
>  }
>
>  static void
> @@ -1199,6 +1209,9 @@ static void mvpp2_interrupts_unmask(void *arg)
>
>                 mvpp2_thread_write(port->priv, v->sw_thread_id,
>                                    MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
> +               mvpp2_thread_write(port->priv, v->sw_thread_id,
> +                                  MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
> +                                  MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
>         }
>  }
>
> @@ -2404,6 +2417,22 @@ static void mvpp2_txp_max_tx_size_set(struct mvpp2_port *port)
>         }
>  }
>
> +/* Routine set the number of non-occupied descriptors threshold that change
> + * interrupt error cause polled by FW Flow Control
> + */

nit: no need for "Routine". Also, does "change .. cause" mean "that
triggers an interrupt"?

Re: [PATCH v4 net-next 11/19] net: mvpp2: add spinlock for FW FCA configuration path

[Willem de Bruijn]

On Wed, Jan 27, 2021 at 7:19 AM <stefanc@marvell.com> wrote:
>
> From: Stefan Chulski <stefanc@marvell.com>
>
> Spinlock added to MSS shared memory configuration space.
>
> Signed-off-by: Stefan Chulski <stefanc@marvell.com>
> ---
>  drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 5 +++++
>  drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 3 +++
>  2 files changed, 8 insertions(+)
>
> diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> index 9d8993f..f34e260 100644
> --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> @@ -1021,6 +1021,11 @@ struct mvpp2 {
>
>         /* CM3 SRAM pool */
>         struct gen_pool *sram_pool;
> +
> +       bool custom_dma_mask;
> +
> +       /* Spinlocks for CM3 shared memory configuration */
> +       spinlock_t mss_spinlock;

Does this need to be a stand-alone patch? This introduces a spinlock,
but does not use it.

Also, is the introduction of custom_dma_mask in this commit on purpose?

Re: [PATCH v4 net-next 00/19] net: mvpp2: Add TX Flow Control support

[Willem de Bruijn]

On Wed, Jan 27, 2021 at 6:50 AM <stefanc@marvell.com> wrote:
>
> From: Stefan Chulski <stefanc@marvell.com>
>
> Armada hardware has a pause generation mechanism in GOP (MAC).
> The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
> However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
> To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
> This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.
>
> Problem is that Packet Processor that actually can drop packets due to lack of resources not connected to the GOP flow control generation mechanism.
> To solve this issue Armada has firmware running on CM3 CPU dedicated for Flow Control support.
> Firmware monitors Packet Processor resources and asserts XON/XOFF by writing to Ports Control 0 Register.
>
> MSS shared SRAM memory used to communicate between CM3 firmware and PP2 driver.
> During init PP2 driver informs firmware about used BM pools, RXQs, congestion and depletion thresholds.
>
> The pause frames are generated whenever congestion or depletion in resources is detected.
> The back pressure is stopped when the resource reaches a sufficient level.
> So the congestion/depletion and sufficient level implement a hysteresis that reduces the XON/XOFF toggle frequency.
>
> Packet Processor v23 hardware introduces support for RX FIFO fill level monitor.
> Patch "add PPv23 version definition" to differ between v23 and v22 hardware.
> Patch "add TX FC firmware check" verifies that CM3 firmware supports Flow Control monitoring.
>
> v3 --> v4
> - Remove RFC tag
>
> v2 --> v3
> - Remove inline functions
> - Add PPv2.3 description into marvell-pp2.txt
> - Improve mvpp2_interrupts_mask/unmask procedure
> - Improve FC enable/disable procedure
> - Add priv->sram_pool check
> - Remove gen_pool_destroy call
> - Reduce Flow Control timer to x100 faster
>
> v1 --> v2
> - Add memory requirements information
> - Add EPROBE_DEFER if of_gen_pool_get return NULL
> - Move Flow control configuration to mvpp2_mac_link_up callback
> - Add firmware version info with Flow control support
>
> Konstantin Porotchkin (1):
>   dts: marvell: add CM3 SRAM memory to cp115 ethernet device tree
>
> Stefan Chulski (18):
>   doc: marvell: add cm3-mem device tree bindings description
>   net: mvpp2: add CM3 SRAM memory map
>   doc: marvell: add PPv2.3 description to marvell-pp2.txt
>   net: mvpp2: add PPv23 version definition
>   net: mvpp2: always compare hw-version vs MVPP21
>   net: mvpp2: increase BM pool size to 2048 buffers
>   net: mvpp2: increase RXQ size to 1024 descriptors
>   net: mvpp2: add FCA periodic timer configurations
>   net: mvpp2: add FCA RXQ non occupied descriptor threshold
>   net: mvpp2: add spinlock for FW FCA configuration path
>   net: mvpp2: enable global flow control
>   net: mvpp2: add RXQ flow control configurations
>   net: mvpp2: add ethtool flow control configuration support
>   net: mvpp2: add BM protection underrun feature support
>   net: mvpp2: add PPv23 RX FIFO flow control
>   net: mvpp2: set 802.3x GoP Flow Control mode
>   net: mvpp2: limit minimum ring size to 1024 descriptors
>   net: mvpp2: add TX FC firmware check
>
>  Documentation/devicetree/bindings/net/marvell-pp2.txt |   4 +-
>  arch/arm64/boot/dts/marvell/armada-cp11x.dtsi         |  10 +
>  drivers/net/ethernet/marvell/mvpp2/mvpp2.h            | 130 ++++-
>  drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c       | 564 ++++++++++++++++++--
>  4 files changed, 658 insertions(+), 50 deletions(-)

Besides the per patch comments, see also the patchwork state for the
patches. Patch 3 and 12 seem to introduce new build warnings or
errors. And one patch misses the sign-off of the author in the From
line.

RE: [EXT] Re: [PATCH v4 net-next 11/19] net: mvpp2: add spinlock for FW FCA configuration path

[Stefan Chulski]

> > index 9d8993f..f34e260 100644
> > --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> > +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> > @@ -1021,6 +1021,11 @@ struct mvpp2 {
> >
> >         /* CM3 SRAM pool */
> >         struct gen_pool *sram_pool;
> > +
> > +       bool custom_dma_mask;
> > +
> > +       /* Spinlocks for CM3 shared memory configuration */
> > +       spinlock_t mss_spinlock;
> 
> Does this need to be a stand-alone patch? This introduces a spinlock, but
> does not use it.
> 
> Also, is the introduction of custom_dma_mask in this commit on purpose?

I would add this change to another patch. custom_dma_mask should be removed.

Thanks,
Stefan.

RE: [EXT] Re: [PATCH v4 net-next 10/19] net: mvpp2: add FCA RXQ non occupied descriptor threshold

[Stefan Chulski]

 >
> > From: Stefan Chulski <stefanc@marvell.com>
> >
> > RXQ non occupied descriptor threshold would be used by Flow Control
> > Firmware feature to move to the XOFF mode.
> > RXQ non occupied threshold would change interrupt cause that polled by
> > CM3 Firmware.
> > Actual non occupied interrupt masked and won't trigger interrupt.
> 
> Does this mean that this change enables a feature, but it is unused due to a
> masked interrupt?

Firmware poll RXQ non occupied cause register to indicate if number of registers bellow threshold.
We do not trigger any interrupt, just poll this bit in CM3. So this cause always masked.

> >
> > Signed-off-by: Stefan Chulski <stefanc@marvell.com>
> > ---
> >  drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  3 ++
> >  drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 46
> > +++++++++++++++++---
> >  2 files changed, 42 insertions(+), 7 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> > b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> > index 73f087c..9d8993f 100644
> > --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> > +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
> > @@ -295,6 +295,8 @@
> >  #define     MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK
> 0x3fc00000
> >  #define     MVPP2_PON_CAUSE_MISC_SUM_MASK              BIT(31)
> >  #define MVPP2_ISR_MISC_CAUSE_REG               0x55b0
> > +#define MVPP2_ISR_RX_ERR_CAUSE_REG(port)       (0x5520 + 4 * (port))
> > +#define            MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK  0x00ff
> 
> The indentation in this file is inconsistent. Here even between the two newly
> introduced lines.

Ok, I would fix this.

> >         /* If the thread isn't used, don't do anything */
> > -       if (smp_processor_id() > port->priv->nthreads)
> > +       if (cpu >= port->priv->nthreads)
> >                 return;
> 
> Here and below, the change from greater than to greater than is really a
> (standalone) fix?

Ok, I would move this to separate patch.

> > +/* Routine set the number of non-occupied descriptors threshold that
> > +change
> > + * interrupt error cause polled by FW Flow Control  */
> 
> nit: no need for "Routine". Also, does "change .. cause" mean "that triggers
> an interrupt"?

Ok.

Thanks,
Stefan.

Re: [EXT] Re: [PATCH v4 net-next 10/19] net: mvpp2: add FCA RXQ non occupied descriptor threshold

[Russell King - ARM Linux admin]

On Wed, Jan 27, 2021 at 06:41:32PM +0000, Stefan Chulski wrote:
> 
>  >
> > > From: Stefan Chulski <stefanc@marvell.com>
> > >
> > > RXQ non occupied descriptor threshold would be used by Flow Control
> > > Firmware feature to move to the XOFF mode.
> > > RXQ non occupied threshold would change interrupt cause that polled by
> > > CM3 Firmware.
> > > Actual non occupied interrupt masked and won't trigger interrupt.
> > 
> > Does this mean that this change enables a feature, but it is unused due to a
> > masked interrupt?
> 
> Firmware poll RXQ non occupied cause register to indicate if number of registers bellow threshold.
> We do not trigger any interrupt, just poll this bit in CM3. So this cause always masked.

The functional spec for A8040 says that the register at 0xF2005520
is "RX Exceptions Interrupt Mask" and the bit description talks about
it controlling interrupt signal generation. However, the bit that
allows RX Exceptions to be raised in MVPP2_ISR_RX_TX_MASK_REG is clear,
so it won't proceed beyond the next level up.

So, I think the commit description needs to say something like:

"The firmware needs to monitor the RX Non-occupied descriptor bits for
 flow control to move to XOFF mode. These bits need to be unmasked to
 be functional, but they will not raise interrupts as we leave the
 RX exception summary bit in MVPP2_ISR_RX_TX_MASK_REG clear."

I think that's essentially what you're trying to describe - please
change if not.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH v4 net-next 00/19] net: mvpp2: Add TX Flow Control support

[Russell King - ARM Linux admin]

On Wed, Jan 27, 2021 at 01:43:16PM +0200, stefanc@marvell.com wrote:
> Armada hardware has a pause generation mechanism in GOP (MAC).
> The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
> However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
> To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
> This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.

I've tested this on my Macchiatobin SingleShot, which seems to be Ax
silicon (and I've checked a couple of my other Armada 8040 platforms
which are also Ax silicon too) and networking remains functional
without flow control with the gigabit port achieving wire speed. I
have not yet tested the 10G ports.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH v4 net-next 00/19] net: mvpp2: Add TX Flow Control support

[Marcin Wojtas]

czw., 28 sty 2021 o 17:43 Russell King - ARM Linux admin
<linux@armlinux.org.uk> napisał(a):
>
> On Wed, Jan 27, 2021 at 01:43:16PM +0200, stefanc@marvell.com wrote:
> > Armada hardware has a pause generation mechanism in GOP (MAC).
> > The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
> > However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
> > To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
> > This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.
>
> I've tested this on my Macchiatobin SingleShot, which seems to be Ax
> silicon (and I've checked a couple of my other Armada 8040 platforms
> which are also Ax silicon too) and networking remains functional
> without flow control with the gigabit port achieving wire speed. I
> have not yet tested the 10G ports.
>
> --

Thanks Russell.

I'll stress and verify CN913x platform with the appropriate firmware.
This should happen after the weekend, as I don't have an immediate
access to our lab in order to replug the cables. I'll update here
about the results.

Best regards,
Marcin