[PATCH v6 net-next 00/18] net: mvpp2: Add TX Flow Control support

[PATCH v6 net-next 00/18] net: mvpp2: Add TX Flow Control support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Armada hardware has a pause generation mechanism in GOP (MAC).
The GOP generate flow control frames based on an indication programmed in Ports Control 0 Register. There is a bit per port.
However assertion of the PortX Pause bits in the ports control 0 register only sends a one time pause.
To complement the function the GOP has a mechanism to periodically send pause control messages based on periodic counters.
This mechanism ensures that the pause is effective as long as the Appropriate PortX Pause is asserted.

Problem is that Packet Processor that actually can drop packets due to lack of resources not connected to the GOP flow control generation mechanism.
To solve this issue Armada has firmware running on CM3 CPU dedicated for Flow Control support.
Firmware monitors Packet Processor resources and asserts XON/XOFF by writing to Ports Control 0 Register.

MSS shared SRAM memory used to communicate between CM3 firmware and PP2 driver.
During init PP2 driver informs firmware about used BM pools, RXQs, congestion and depletion thresholds.

The pause frames are generated whenever congestion or depletion in resources is detected.
The back pressure is stopped when the resource reaches a sufficient level.
So the congestion/depletion and sufficient level implement a hysteresis that reduces the XON/XOFF toggle frequency.

Packet Processor v23 hardware introduces support for RX FIFO fill level monitor.
Patch "add PPv23 version definition" to differ between v23 and v22 hardware.
Patch "add TX FC firmware check" verifies that CM3 firmware supports Flow Control monitoring.

v5 --> v6
- No change

v4 --> v5
- Add missed Signed-off
- Fix warnings in patches 3 and 12
- Add revision requirement to warning message
- Move mss_spinlock into RXQ flow control configurations patch
- Improve FCA RXQ non occupied descriptor threshold commit message

v3 --> v4
- Remove RFC tag

v2 --> v3
- Remove inline functions
- Add PPv2.3 description into marvell-pp2.txt
- Improve mvpp2_interrupts_mask/unmask procedure
- Improve FC enable/disable procedure
- Add priv->sram_pool check
- Remove gen_pool_destroy call
- Reduce Flow Control timer to x100 faster

v1 --> v2
- Add memory requirements information
- Add EPROBE_DEFER if of_gen_pool_get return NULL
- Move Flow control configuration to mvpp2_mac_link_up callback
- Add firmware version info with Flow control support

Konstantin Porotchkin (1):
  dts: marvell: add CM3 SRAM memory to cp115 ethernet device tree

Stefan Chulski (17):
  doc: marvell: add cm3-mem device tree bindings description
  net: mvpp2: add CM3 SRAM memory map
  doc: marvell: add PPv2.3 description to marvell-pp2.txt
  net: mvpp2: add PPv23 version definition
  net: mvpp2: always compare hw-version vs MVPP21
  net: mvpp2: increase BM pool size to 2048 buffers
  net: mvpp2: increase RXQ size to 1024 descriptors
  net: mvpp2: add FCA periodic timer configurations
  net: mvpp2: add FCA RXQ non occupied descriptor threshold
  net: mvpp2: enable global flow control
  net: mvpp2: add RXQ flow control configurations
  net: mvpp2: add ethtool flow control configuration support
  net: mvpp2: add BM protection underrun feature support
  net: mvpp2: add PPv23 RX FIFO flow control
  net: mvpp2: set 802.3x GoP Flow Control mode
  net: mvpp2: limit minimum ring size to 1024 descriptors
  net: mvpp2: add TX FC firmware check

 Documentation/devicetree/bindings/net/marvell-pp2.txt |   4 +-
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi         |  10 +
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h            | 128 ++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c       | 563 ++++++++++++++++++--
 4 files changed, 655 insertions(+), 50 deletions(-)

-- 
1.9.1

[PATCH v6 net-next 01/18] doc: marvell: add cm3-mem device tree bindings description

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 Documentation/devicetree/bindings/net/marvell-pp2.txt | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index b783976..f9f8cc6 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -37,6 +37,7 @@ Required properties (port):
   GOP (Group Of Ports) point of view. This ID is used to index the
   per-port registers in the second register area.
 - phy-mode: See ethernet.txt file in the same directory
+- cm3-mem: phandle to CM3 SRAM definitions
 
 Optional properties (port):
 
-- 
1.9.1

[PATCH v6 net-next 02/18] dts: marvell: add CM3 SRAM memory to cp115 ethernet device tree

[stefanc]

From: Konstantin Porotchkin <kostap@marvell.com>

CM3 SRAM address space would be used for Flow Control configuration.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
---
 arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 9dcf16b..359cf42 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -69,6 +69,8 @@
 			status = "disabled";
 			dma-coherent;
 
+			cm3-mem = <&CP11X_LABEL(cm3_sram)>;
+
 			CP11X_LABEL(eth0): eth0 {
 				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>,
 					<43 IRQ_TYPE_LEVEL_HIGH>,
@@ -211,6 +213,14 @@
 			};
 		};
 
+		CP11X_LABEL(cm3_sram): cm3@220000 {
+			compatible = "mmio-sram";
+			reg = <0x220000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x220000 0x800>;
+		};
+
 		CP11X_LABEL(rtc): rtc@284000 {
 			compatible = "marvell,armada-8k-rtc";
 			reg = <0x284000 0x20>, <0x284080 0x24>;
-- 
1.9.1

[PATCH v6 net-next 04/18] doc: marvell: add PPv2.3 description to marvell-pp2.txt

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 Documentation/devicetree/bindings/net/marvell-pp2.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt
index f9f8cc6..df80cff 100644
--- a/Documentation/devicetree/bindings/net/marvell-pp2.txt
+++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt
@@ -1,5 +1,6 @@
 * Marvell Armada 375 Ethernet Controller (PPv2.1)
   Marvell Armada 7K/8K Ethernet Controller (PPv2.2)
+  Marvell CN913X Ethernet Controller (PPv2.3)
 
 Required properties:
 
@@ -12,7 +13,7 @@ Required properties:
 	- common controller registers
 	- LMS registers
 	- one register area per Ethernet port
-  For "marvell,armada-7k-pp2", must contain the following register
+  For "marvell,armada-7k-pp2" used by 7K/8K and CN913X, must contain the following register
   sets:
 	- packet processor registers
 	- networking interfaces registers
-- 
1.9.1

[PATCH v6 net-next 06/18] net: mvpp2: always compare hw-version vs MVPP21

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 36 ++++++++++----------
 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 11c56d2..d80947a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -320,7 +320,7 @@ static int mvpp2_get_nrxqs(struct mvpp2 *priv)
 {
 	unsigned int nrxqs;
 
-	if (priv->hw_version == MVPP22 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
+	if (priv->hw_version != MVPP21 && queue_mode == MVPP2_QDIST_SINGLE_MODE)
 		return 1;
 
 	/* According to the PPv2.2 datasheet and our experiments on
@@ -447,7 +447,7 @@ static void mvpp2_bm_bufs_get_addrs(struct device *dev, struct mvpp2 *priv,
 				      MVPP2_BM_PHY_ALLOC_REG(bm_pool->id));
 	*phys_addr = mvpp2_thread_read(priv, thread, MVPP2_BM_VIRT_ALLOC_REG);
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		u32 val;
 		u32 dma_addr_highbits, phys_addr_highbits;
 
@@ -743,7 +743,7 @@ static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 	if (test_bit(thread, &port->priv->lock_map))
 		spin_lock_irqsave(&port->bm_lock[thread], flags);
 
-	if (port->priv->hw_version == MVPP22) {
+	if (port->priv->hw_version != MVPP21) {
 		u32 val = 0;
 
 		if (sizeof(dma_addr_t) == 8)
@@ -1200,7 +1200,7 @@ static bool mvpp2_port_supports_xlg(struct mvpp2_port *port)
 
 static bool mvpp2_port_supports_rgmii(struct mvpp2_port *port)
 {
-	return !(port->priv->hw_version == MVPP22 && port->gop_id == 0);
+	return !(port->priv->hw_version != MVPP21 && port->gop_id == 0);
 }
 
 /* Port configuration routines */
@@ -1818,7 +1818,7 @@ static void mvpp2_mac_reset_assert(struct mvpp2_port *port)
 	      MVPP2_GMAC_PORT_RESET_MASK;
 	writel(val, port->base + MVPP2_GMAC_CTRL_2_REG);
 
-	if (port->priv->hw_version == MVPP22 && port->gop_id == 0) {
+	if (port->priv->hw_version != MVPP21 && port->gop_id == 0) {
 		val = readl(port->base + MVPP22_XLG_CTRL0_REG) &
 		      ~MVPP22_XLG_CTRL0_MAC_RESET_DIS;
 		writel(val, port->base + MVPP22_XLG_CTRL0_REG);
@@ -1831,7 +1831,7 @@ static void mvpp22_pcs_reset_assert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -1852,7 +1852,7 @@ static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
 	void __iomem *mpcs, *xpcs;
 	u32 val;
 
-	if (port->priv->hw_version != MVPP22 || port->gop_id != 0)
+	if (port->priv->hw_version == MVPP21 || port->gop_id != 0)
 		return;
 
 	mpcs = priv->iface_base + MVPP22_MPCS_BASE(port->gop_id);
@@ -4189,7 +4189,7 @@ static void mvpp2_start_dev(struct mvpp2_port *port)
 	/* Enable interrupts on all threads */
 	mvpp2_interrupts_enable(port);
 
-	if (port->priv->hw_version == MVPP22)
+	if (port->priv->hw_version != MVPP21)
 		mvpp22_mode_reconfigure(port);
 
 	if (port->phylink) {
@@ -4405,7 +4405,7 @@ static int mvpp2_open(struct net_device *dev)
 		valid = true;
 	}
 
-	if (priv->hw_version == MVPP22 && port->port_irq) {
+	if (priv->hw_version != MVPP21 && port->port_irq) {
 		err = request_irq(port->port_irq, mvpp2_port_isr, 0,
 				  dev->name, port);
 		if (err) {
@@ -6053,7 +6053,7 @@ static int mvpp2__mac_prepare(struct phylink_config *config, unsigned int mode,
 			     MVPP2_GMAC_PORT_RESET_MASK,
 			     MVPP2_GMAC_PORT_RESET_MASK);
 
-		if (port->priv->hw_version == MVPP22) {
+		if (port->priv->hw_version != MVPP21) {
 			mvpp22_gop_mask_irq(port);
 
 			phy_power_off(port->comphy);
@@ -6107,7 +6107,7 @@ static int mvpp2_mac_finish(struct phylink_config *config, unsigned int mode,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 
-	if (port->priv->hw_version == MVPP22 &&
+	if (port->priv->hw_version != MVPP21 &&
 	    port->phy_interface != interface) {
 		port->phy_interface = interface;
 
@@ -6787,7 +6787,7 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	if (dram_target_info)
 		mvpp2_conf_mbus_windows(dram_target_info, priv);
 
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		mvpp2_axi_init(priv);
 
 	/* Disable HW PHY polling */
@@ -6950,7 +6950,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
 	}
 
-	if (priv->hw_version == MVPP22 && dev_of_node(&pdev->dev)) {
+	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
 		priv->sysctrl_base =
 			syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
 							"marvell,system-controller");
@@ -6963,7 +6963,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 			priv->sysctrl_base = NULL;
 	}
 
-	if (priv->hw_version == MVPP22 &&
+	if (priv->hw_version != MVPP21 &&
 	    mvpp2_get_nrxqs(priv) * 2 <= MVPP2_BM_MAX_POOLS)
 		priv->percpu_pools = 1;
 
@@ -7010,7 +7010,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		if (err < 0)
 			goto err_pp_clk;
 
-		if (priv->hw_version == MVPP22) {
+		if (priv->hw_version != MVPP21) {
 			priv->mg_clk = devm_clk_get(&pdev->dev, "mg_clk");
 			if (IS_ERR(priv->mg_clk)) {
 				err = PTR_ERR(priv->mg_clk);
@@ -7051,7 +7051,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	if (priv->hw_version == MVPP22) {
+	if (priv->hw_version != MVPP21) {
 		err = dma_set_mask(&pdev->dev, MVPP2_DESC_DMA_MASK);
 		if (err)
 			goto err_axi_clk;
@@ -7131,10 +7131,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 	clk_disable_unprepare(priv->axi_clk);
 
 err_mg_core_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_core_clk);
 err_mg_clk:
-	if (priv->hw_version == MVPP22)
+	if (priv->hw_version != MVPP21)
 		clk_disable_unprepare(priv->mg_clk);
 err_gop_clk:
 	clk_disable_unprepare(priv->gop_clk);
-- 
1.9.1

[PATCH v6 net-next 08/18] net: mvpp2: increase RXQ size to 1024 descriptors

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC is 1024 buffers.
Default set to 1024 descriptors and maximum size to 2048.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 8dc669d..cac9885 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -715,8 +715,8 @@
 #define MVPP2_PORT_MAX_RXQ		32
 
 /* Max number of Rx descriptors */
-#define MVPP2_MAX_RXD_MAX		1024
-#define MVPP2_MAX_RXD_DFLT		128
+#define MVPP2_MAX_RXD_MAX		2048
+#define MVPP2_MAX_RXD_DFLT		1024
 
 /* Max number of Tx descriptors */
 #define MVPP2_MAX_TXD_MAX		2048
-- 
1.9.1

[PATCH v6 net-next 09/18] net: mvpp2: add FCA periodic timer configurations

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 +++++-
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 45 ++++++++++++++++++++
 2 files changed, 57 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index cac9885..73f087c 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -596,6 +596,15 @@
 #define     MVPP22_MPCS_CLK_RESET_DIV_RATIO(n)	((n) << 4)
 #define     MVPP22_MPCS_CLK_RESET_DIV_SET	BIT(11)
 
+/* FCA registers. PPv2.2 and PPv2.3 */
+#define MVPP22_FCA_BASE(port)			(0x7600 + (port) * 0x1000)
+#define MVPP22_FCA_REG_SIZE			16
+#define MVPP22_FCA_REG_MASK			0xFFFF
+#define MVPP22_FCA_CONTROL_REG			0x0
+#define MVPP22_FCA_ENABLE_PERIODIC		BIT(11)
+#define MVPP22_PERIODIC_COUNTER_LSB_REG		(0x110)
+#define MVPP22_PERIODIC_COUNTER_MSB_REG		(0x114)
+
 /* XPCS registers. PPv2.2 and PPv2.3 */
 #define MVPP22_XPCS_BASE(port)			(0x7400 + (port) * 0x1000)
 #define MVPP22_XPCS_CFG0			0x0
@@ -752,7 +761,9 @@
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
 /* MSS Flow control */
-#define MSS_SRAM_SIZE	0x800
+#define MSS_SRAM_SIZE		0x800
+#define FC_QUANTA		0xFFFF
+#define FC_CLK_DIVIDER		100
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index d80947a..6e59d07 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1281,6 +1281,49 @@ static void mvpp22_gop_init_10gkr(struct mvpp2_port *port)
 	writel(val, mpcs + MVPP22_MPCS_CLK_RESET);
 }
 
+static void mvpp22_gop_fca_enable_periodic(struct mvpp2_port *port, bool en)
+{
+	struct mvpp2 *priv = port->priv;
+	void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+	u32 val;
+
+	val = readl(fca + MVPP22_FCA_CONTROL_REG);
+	val &= ~MVPP22_FCA_ENABLE_PERIODIC;
+	if (en)
+		val |= MVPP22_FCA_ENABLE_PERIODIC;
+	writel(val, fca + MVPP22_FCA_CONTROL_REG);
+}
+
+static void mvpp22_gop_fca_set_timer(struct mvpp2_port *port, u32 timer)
+{
+	struct mvpp2 *priv = port->priv;
+	void __iomem *fca = priv->iface_base + MVPP22_FCA_BASE(port->gop_id);
+	u32 lsb, msb;
+
+	lsb = timer & MVPP22_FCA_REG_MASK;
+	msb = timer >> MVPP22_FCA_REG_SIZE;
+
+	writel(lsb, fca + MVPP22_PERIODIC_COUNTER_LSB_REG);
+	writel(msb, fca + MVPP22_PERIODIC_COUNTER_MSB_REG);
+}
+
+/* Set Flow Control timer x100 faster than pause quanta to ensure that link
+ * partner won't send traffic if port is in XOFF mode.
+ */
+static void mvpp22_gop_fca_set_periodic_timer(struct mvpp2_port *port)
+{
+	u32 timer;
+
+	timer = (port->priv->tclk / (USEC_PER_SEC * FC_CLK_DIVIDER))
+		* FC_QUANTA;
+
+	mvpp22_gop_fca_enable_periodic(port, false);
+
+	mvpp22_gop_fca_set_timer(port, timer);
+
+	mvpp22_gop_fca_enable_periodic(port, true);
+}
+
 static int mvpp22_gop_init(struct mvpp2_port *port)
 {
 	struct mvpp2 *priv = port->priv;
@@ -1325,6 +1368,8 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
 	val |= GENCONF_SOFT_RESET1_GOP;
 	regmap_write(priv->sysctrl_base, GENCONF_SOFT_RESET1, val);
 
+	mvpp22_gop_fca_set_periodic_timer(port);
+
 unsupported_conf:
 	return 0;
 
-- 
1.9.1

[PATCH v6 net-next 10/18] net: mvpp2: add FCA RXQ non occupied descriptor threshold

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  3 ++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 44 ++++++++++++++++----
 2 files changed, 40 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 73f087c..ca84995 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -295,6 +295,8 @@
 #define     MVPP2_PON_CAUSE_TXP_OCCUP_DESC_ALL_MASK	0x3fc00000
 #define     MVPP2_PON_CAUSE_MISC_SUM_MASK		BIT(31)
 #define MVPP2_ISR_MISC_CAUSE_REG		0x55b0
+#define MVPP2_ISR_RX_ERR_CAUSE_REG(port)	(0x5520 + 4 * (port))
+#define     MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK	0x00ff
 
 /* Buffer Manager registers */
 #define MVPP2_BM_POOL_BASE_REG(pool)		(0x6000 + ((pool) * 4))
@@ -764,6 +766,7 @@
 #define MSS_SRAM_SIZE		0x800
 #define FC_QUANTA		0xFFFF
 #define FC_CLK_DIVIDER		100
+#define MSS_THRESHOLD_STOP	768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 6e59d07..19a3f38 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -1134,14 +1134,19 @@ static inline void mvpp2_qvec_interrupt_disable(struct mvpp2_queue_vector *qvec)
 static void mvpp2_interrupts_mask(void *arg)
 {
 	struct mvpp2_port *port = arg;
+	int cpu = smp_processor_id();
+	u32 thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu >= port->priv->nthreads)
 		return;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), 0);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id), 0);
 }
 
 /* Unmask the current thread's Rx/Tx interrupts.
@@ -1151,20 +1156,25 @@ static void mvpp2_interrupts_mask(void *arg)
 static void mvpp2_interrupts_unmask(void *arg)
 {
 	struct mvpp2_port *port = arg;
-	u32 val;
+	int cpu = smp_processor_id();
+	u32 val, thread;
 
 	/* If the thread isn't used, don't do anything */
-	if (smp_processor_id() > port->priv->nthreads)
+	if (cpu >= port->priv->nthreads)
 		return;
 
+	thread = mvpp2_cpu_to_thread(port->priv, cpu);
+
 	val = MVPP2_CAUSE_MISC_SUM_MASK |
 		MVPP2_CAUSE_RXQ_OCCUP_DESC_ALL_MASK(port->priv->hw_version);
 	if (port->has_tx_irqs)
 		val |= MVPP2_CAUSE_TXQ_OCCUP_DESC_ALL_MASK;
 
-	mvpp2_thread_write(port->priv,
-			   mvpp2_cpu_to_thread(port->priv, smp_processor_id()),
+	mvpp2_thread_write(port->priv, thread,
 			   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+	mvpp2_thread_write(port->priv, thread,
+			   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+			   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 }
 
 static void
@@ -1189,6 +1199,9 @@ static void mvpp2_interrupts_unmask(void *arg)
 
 		mvpp2_thread_write(port->priv, v->sw_thread_id,
 				   MVPP2_ISR_RX_TX_MASK_REG(port->id), val);
+		mvpp2_thread_write(port->priv, v->sw_thread_id,
+				   MVPP2_ISR_RX_ERR_CAUSE_REG(port->id),
+				   MVPP2_ISR_RX_ERR_CAUSE_NONOCC_MASK);
 	}
 }
 
@@ -2394,6 +2407,20 @@ static void mvpp2_txp_max_tx_size_set(struct mvpp2_port *port)
 	}
 }
 
+/* Set the number of non-occupied descriptors threshold */
+static void mvpp2_set_rxq_free_tresh(struct mvpp2_port *port,
+				     struct mvpp2_rx_queue *rxq)
+{
+	u32 val;
+
+	mvpp2_write(port->priv, MVPP2_RXQ_NUM_REG, rxq->id);
+
+	val = mvpp2_read(port->priv, MVPP2_RXQ_THRESH_REG);
+	val &= ~MVPP2_RXQ_NON_OCCUPIED_MASK;
+	val |= MSS_THRESHOLD_STOP << MVPP2_RXQ_NON_OCCUPIED_OFFSET;
+	mvpp2_write(port->priv, MVPP2_RXQ_THRESH_REG, val);
+}
+
 /* Set the number of packets that will be received before Rx interrupt
  * will be generated by HW.
  */
@@ -2649,6 +2676,9 @@ static int mvpp2_rxq_init(struct mvpp2_port *port,
 	mvpp2_rx_pkts_coal_set(port, rxq);
 	mvpp2_rx_time_coal_set(port, rxq);
 
+	/* Set the number of non occupied descriptors threshold */
+	mvpp2_set_rxq_free_tresh(port, rxq);
+
 	/* Add number of descriptors ready for receiving packets */
 	mvpp2_rxq_status_update(port, rxq->id, 0, rxq->size);
 
-- 
1.9.1

[PATCH v6 net-next 11/18] net: mvpp2: enable global flow control

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch enables global flow control in FW and in the
phylink validate mask.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 ++++++---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 30 +++++++++++++++++++-
 2 files changed, 38 insertions(+), 5 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index ca84995..e010410 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -763,10 +763,12 @@
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
 /* MSS Flow control */
-#define MSS_SRAM_SIZE		0x800
-#define FC_QUANTA		0xFFFF
-#define FC_CLK_DIVIDER		100
-#define MSS_THRESHOLD_STOP	768
+#define MSS_SRAM_SIZE			0x800
+#define MSS_FC_COM_REG			0
+#define FLOW_CONTROL_ENABLE_BIT		BIT(0)
+#define FC_QUANTA			0xFFFF
+#define FC_CLK_DIVIDER			100
+#define MSS_THRESHOLD_STOP		768
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
@@ -1021,6 +1023,9 @@ struct mvpp2 {
 
 	/* CM3 SRAM pool */
 	struct gen_pool *sram_pool;
+
+	/* Global TX Flow Control config */
+	bool global_tx_fc;
 };
 
 struct mvpp2_pcpu_stats {
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 19a3f38..770f45a 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -92,6 +92,16 @@ static inline u32 mvpp2_cpu_to_thread(struct mvpp2 *priv, int cpu)
 	return cpu % priv->nthreads;
 }
 
+static void mvpp2_cm3_write(struct mvpp2 *priv, u32 offset, u32 data)
+{
+	writel(data, priv->cm3_base + offset);
+}
+
+static u32 mvpp2_cm3_read(struct mvpp2 *priv, u32 offset)
+{
+	return readl(priv->cm3_base + offset);
+}
+
 static struct page_pool *
 mvpp2_create_page_pool(struct device *dev, int num, int len,
 		       enum dma_data_direction dma_dir)
@@ -5951,6 +5961,11 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
 	phylink_set(mask, Autoneg);
 	phylink_set_port_modes(mask);
 
+	if (port->priv->global_tx_fc) {
+		phylink_set(mask, Pause);
+		phylink_set(mask, Asym_Pause);
+	}
+
 	switch (state->interface) {
 	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XAUI:
@@ -6969,7 +6984,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err;
+	int err, val;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -7023,6 +7038,10 @@ static int mvpp2_probe(struct platform_device *pdev)
 			return err;
 		else if (err)
 			dev_warn(&pdev->dev, "Fail to alloc CM3 SRAM\n");
+
+		/* Enable global Flow Control only if handler to SRAM not NULL */
+		if (priv->cm3_base)
+			priv->global_tx_fc = true;
 	}
 
 	if (priv->hw_version != MVPP21 && dev_of_node(&pdev->dev)) {
@@ -7190,6 +7209,15 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+		val |= FLOW_CONTROL_ENABLE_BIT;
+		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+	}
+
 	mvpp2_dbgfs_init(priv, pdev->name);
 
 	platform_set_drvdata(pdev, priv);
-- 
1.9.1

[PATCH v6 net-next 13/18] net: mvpp2: add ethtool flow control configuration support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch add ethtool flow control configuration support.

Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.

Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 13 +++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 98 ++++++++++++++++++++
 2 files changed, 111 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 0f27be0..9071ab6 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -775,6 +775,19 @@
 #define MSS_RXQ_TRESH_REG(q, fq)	(MSS_RXQ_TRESH_BASE + (((q) + (fq)) \
 					* MSS_RXQ_TRESH_OFFS))
 
+#define MSS_BUF_POOL_BASE		0x40
+#define MSS_BUF_POOL_OFFS		4
+#define MSS_BUF_POOL_REG(id)		(MSS_BUF_POOL_BASE		\
+					+ (id) * MSS_BUF_POOL_OFFS)
+
+#define MSS_BUF_POOL_STOP_MASK		0xFFF
+#define MSS_BUF_POOL_START_MASK		(0xFFF << MSS_BUF_POOL_START_OFFS)
+#define MSS_BUF_POOL_START_OFFS		12
+#define MSS_BUF_POOL_PORTS_MASK		(0xF << MSS_BUF_POOL_PORTS_OFFS)
+#define MSS_BUF_POOL_PORTS_OFFS		24
+#define MSS_BUF_POOL_PORT_OFFS(id)	(0x1 <<				\
+					((id) + MSS_BUF_POOL_PORTS_OFFS))
+
 #define MSS_RXQ_TRESH_START_MASK	0xFFFF
 #define MSS_RXQ_TRESH_STOP_MASK		(0xFFFF << MSS_RXQ_TRESH_STOP_OFFS)
 #define MSS_RXQ_TRESH_STOP_OFFS		16
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index cb2d0c5..1d4d5a8 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -846,6 +846,59 @@ static void mvpp2_rxq_disable_fc(struct mvpp2_port *port)
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+/* Routine disable/enable flow control for BM pool condition */
+static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
+				    struct mvpp2_bm_pool *pool,
+				    bool en)
+{
+	int val, cm3_state;
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->priv->mss_spinlock, flags);
+
+	/* Remove Flow control enable bit to prevent race between FW and Kernel
+	 * If Flow control were enabled, it would be re-enabled.
+	 */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	cm3_state = (val & FLOW_CONTROL_ENABLE_BIT);
+	val &= ~FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	/* Check if BM pool should be enabled/disable */
+	if (en) {
+		/* Set BM pool start and stop thresholds per port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val |= MSS_BUF_POOL_PORT_OFFS(port->id);
+		val &= ~MSS_BUF_POOL_START_MASK;
+		val |= (MSS_THRESHOLD_START << MSS_BUF_POOL_START_OFFS);
+		val &= ~MSS_BUF_POOL_STOP_MASK;
+		val |= MSS_THRESHOLD_STOP;
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	} else {
+		/* Remove BM pool from the port */
+		val = mvpp2_cm3_read(port->priv, MSS_BUF_POOL_REG(pool->id));
+		val &= ~MSS_BUF_POOL_PORT_OFFS(port->id);
+
+		/* Zero BM pool start and stop thresholds to disable pool
+		 * flow control if pool empty (not used by any port)
+		 */
+		if (!pool->buf_num) {
+			val &= ~MSS_BUF_POOL_START_MASK;
+			val &= ~MSS_BUF_POOL_STOP_MASK;
+		}
+
+		mvpp2_cm3_write(port->priv, MSS_BUF_POOL_REG(pool->id), val);
+	}
+
+	/* Notify Firmware that Flow control config space ready for update */
+	val = mvpp2_cm3_read(port->priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	val |= cm3_state;
+	mvpp2_cm3_write(port->priv, MSS_FC_COM_REG, val);
+
+	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -1176,6 +1229,16 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		new_long_pool = MVPP2_BM_LONG;
 
 	if (new_long_pool != port->pool_long->id) {
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port,
+							port->pool_short,
+							false);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							false);
+		}
+
 		/* Remove port from old short & long pool */
 		port->pool_long = mvpp2_bm_pool_use(port, port->pool_long->id,
 						    port->pool_long->pkt_size);
@@ -1193,6 +1256,25 @@ static int mvpp2_bm_update_mtu(struct net_device *dev, int mtu)
 		mvpp2_swf_bm_pool_init(port);
 
 		mvpp2_set_hw_csum(port, new_long_pool);
+
+		if (port->tx_fc) {
+			if (pkt_size > MVPP2_BM_LONG_PKT_SIZE)
+				mvpp2_bm_pool_update_fc(port, port->pool_long,
+							true);
+			else
+				mvpp2_bm_pool_update_fc(port, port->pool_short,
+							true);
+		}
+
+		/* Update L4 checksum when jumbo enable/disable on port */
+		if (new_long_pool == MVPP2_BM_JUMBO && port->id != 0) {
+			dev->features &= ~(NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM);
+			dev->hw_features &= ~(NETIF_F_IP_CSUM |
+					      NETIF_F_IPV6_CSUM);
+		} else {
+			dev->features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+			dev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+		}
 	}
 
 out_set:
@@ -6356,6 +6438,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 {
 	struct mvpp2_port *port = mvpp2_phylink_to_port(config);
 	u32 val;
+	int i;
 
 	if (mvpp2_is_xlg(interface)) {
 		if (!phylink_autoneg_inband(mode)) {
@@ -6406,6 +6489,21 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
+	if (port->priv->global_tx_fc) {
+		port->tx_fc = tx_pause;
+		if (tx_pause)
+			mvpp2_rxq_enable_fc(port);
+		else
+			mvpp2_rxq_disable_fc(port);
+		if (port->priv->percpu_pools) {
+			for (i = 0; i < port->nrxqs; i++)
+				mvpp2_bm_pool_update_fc(port, &port->priv->bm_pools[i], tx_pause);
+		} else {
+			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
+			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
+		}
+	}
+
 	mvpp2_port_enable(port);
 
 	mvpp2_egress_enable(port);
-- 
1.9.1

[PATCH v6 net-next 14/18] net: mvpp2: add BM protection underrun feature support

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Feature double size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  8 +++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 35 +++++++++++++++++++-
 2 files changed, 42 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9071ab6..1967493 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -324,6 +324,10 @@
 #define     MVPP2_BM_HIGH_THRESH_MASK		0x7f0000
 #define     MVPP2_BM_HIGH_THRESH_VALUE(val)	((val) << \
 						MVPP2_BM_HIGH_THRESH_OFFS)
+#define     MVPP2_BM_BPPI_HIGH_THRESH		0x1E
+#define     MVPP2_BM_BPPI_LOW_THRESH		0x1C
+#define     MVPP23_BM_BPPI_HIGH_THRESH		0x34
+#define     MVPP23_BM_BPPI_LOW_THRESH		0x28
 #define MVPP2_BM_INTR_CAUSE_REG(pool)		(0x6240 + ((pool) * 4))
 #define     MVPP2_BM_RELEASED_DELAY_MASK	BIT(0)
 #define     MVPP2_BM_ALLOC_FAILED_MASK		BIT(1)
@@ -352,6 +356,10 @@
 #define MVPP2_OVERRUN_ETH_DROP			0x7000
 #define MVPP2_CLS_ETH_DROP			0x7020
 
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG	0x6310
+#define     MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK	0xff
+#define     MVPP23_BM_8POOL_MODE		BIT(8)
+
 /* Hit counters registers */
 #define MVPP2_CTRS_IDX				0x7040
 #define     MVPP22_CTRS_TX_CTR(port, txq)	((txq) | ((port) << 3) | BIT(7))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 1d4d5a8..c7517b1f 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -70,6 +70,11 @@ enum mvpp2_bm_pool_log_num {
 module_param(queue_mode, int, 0444);
 MODULE_PARM_DESC(queue_mode, "Set queue_mode (single=0, multi=1)");
 
+static int bm_underrun_protect = 1;
+
+module_param(bm_underrun_protect, int, 0444);
+MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");
+
 /* Utility/helper methods */
 
 void mvpp2_write(struct mvpp2 *priv, u32 offset, u32 data)
@@ -424,6 +429,21 @@ static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 
 	val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
 	val |= MVPP2_BM_START_MASK;
+
+	val &= ~MVPP2_BM_LOW_THRESH_MASK;
+	val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+	/* Set 8 Pools BPPI threshold if BM underrun protection feature
+	 * were enabled
+	 */
+	if (priv->hw_version == MVPP23 && bm_underrun_protect) {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+	} else {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+	}
+
 	mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
 
 	bm_pool->size = size;
@@ -592,6 +612,16 @@ static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
 	return err;
 }
 
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+	val |= MVPP23_BM_8POOL_MODE;
+	mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
 static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 {
 	enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
@@ -645,6 +675,9 @@ static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 	if (!priv->bm_pools)
 		return -ENOMEM;
 
+	if (priv->hw_version == MVPP23 && bm_underrun_protect)
+		mvpp23_bm_set_8pool_mode(priv);
+
 	err = mvpp2_bm_pools_init(dev, priv);
 	if (err < 0)
 		return err;
@@ -6489,7 +6522,7 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
-	if (port->priv->global_tx_fc) {
+	if (port->priv->global_tx_fc && bm_underrun_protect) {
 		port->tx_fc = tx_pause;
 		if (tx_pause)
 			mvpp2_rxq_enable_fc(port);
-- 
1.9.1

[PATCH v6 net-next 15/18] net: mvpp2: add PPv23 RX FIFO flow control

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

New FIFO flow control feature were added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current  FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      | 15 ++++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 53 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 1967493..9947385 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -770,6 +770,18 @@
 #define MVPP2_TX_FIFO_THRESHOLD(kb)	\
 		((kb) * 1024 - MVPP2_TX_FIFO_THRESHOLD_MIN)
 
+/* RX FIFO threshold in 1KB granularity */
+#define MVPP23_PORT0_FIFO_TRSH	(9 * 1024)
+#define MVPP23_PORT1_FIFO_TRSH	(4 * 1024)
+#define MVPP23_PORT2_FIFO_TRSH	(2 * 1024)
+
+/* RX Flow Control Registers */
+#define MVPP2_RX_FC_REG(port)		(0x150 + 4 * (port))
+#define     MVPP2_RX_FC_EN		BIT(24)
+#define     MVPP2_RX_FC_TRSH_OFFS	16
+#define     MVPP2_RX_FC_TRSH_MASK	(0xFF << MVPP2_RX_FC_TRSH_OFFS)
+#define     MVPP2_RX_FC_TRSH_UNIT	256
+
 /* MSS Flow control */
 #define MSS_SRAM_SIZE			0x800
 #define MSS_FC_COM_REG			0
@@ -1502,6 +1514,8 @@ struct mvpp2_bm_pool {
 
 void mvpp2_dbgfs_cleanup(struct mvpp2 *priv);
 
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en);
+
 #ifdef CONFIG_MVPP2_PTP
 int mvpp22_tai_probe(struct device *dev, struct mvpp2 *priv);
 void mvpp22_tai_tstamp(struct mvpp2_tai *tai, u32 tstamp,
@@ -1534,4 +1548,5 @@ static inline bool mvpp22_rx_hwtstamping(struct mvpp2_port *port)
 {
 	return IS_ENABLED(CONFIG_MVPP2_PTP) && port->rx_hwtstamp;
 }
+
 #endif
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index c7517b1f..afa61cc 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6535,6 +6535,8 @@ static void mvpp2_mac_link_up(struct phylink_config *config,
 			mvpp2_bm_pool_update_fc(port, port->pool_long, tx_pause);
 			mvpp2_bm_pool_update_fc(port, port->pool_short, tx_pause);
 		}
+		if (port->priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_en(port->priv, port->id, tx_pause);
 	}
 
 	mvpp2_port_enable(port);
@@ -7003,6 +7005,55 @@ static void mvpp22_rx_fifo_init(struct mvpp2 *priv)
 	mvpp2_write(priv, MVPP2_RX_FIFO_INIT_REG, 0x1);
 }
 
+/* Configure Rx FIFO Flow control thresholds */
+static void mvpp23_rx_fifo_fc_set_tresh(struct mvpp2 *priv)
+{
+	int port, val;
+
+	/* Port 0: maximum speed -10Gb/s port
+	 *	   required by spec RX FIFO threshold 9KB
+	 * Port 1: maximum speed -5Gb/s port
+	 *	   required by spec RX FIFO threshold 4KB
+	 * Port 2: maximum speed -1Gb/s port
+	 *	   required by spec RX FIFO threshold 2KB
+	 */
+
+	/* Without loopback port */
+	for (port = 0; port < (MVPP2_MAX_PORTS - 1); port++) {
+		if (port == 0) {
+			val = (MVPP23_PORT0_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else if (port == 1) {
+			val = (MVPP23_PORT1_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		} else {
+			val = (MVPP23_PORT2_FIFO_TRSH / MVPP2_RX_FC_TRSH_UNIT)
+				<< MVPP2_RX_FC_TRSH_OFFS;
+			val &= MVPP2_RX_FC_TRSH_MASK;
+			mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+		}
+	}
+}
+
+/* Configure Rx FIFO Flow control thresholds */
+void mvpp23_rx_fifo_fc_en(struct mvpp2 *priv, int port, bool en)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP2_RX_FC_REG(port));
+
+	if (en)
+		val |= MVPP2_RX_FC_EN;
+	else
+		val &= ~MVPP2_RX_FC_EN;
+
+	mvpp2_write(priv, MVPP2_RX_FC_REG(port), val);
+}
+
 static void mvpp22_tx_fifo_set_hw(struct mvpp2 *priv, int port, int size)
 {
 	int threshold = MVPP2_TX_FIFO_THRESHOLD(size);
@@ -7154,6 +7205,8 @@ static int mvpp2_init(struct platform_device *pdev, struct mvpp2 *priv)
 	} else {
 		mvpp22_rx_fifo_init(priv);
 		mvpp22_tx_fifo_init(priv);
+		if (priv->hw_version == MVPP23)
+			mvpp23_rx_fifo_fc_set_tresh(priv);
 	}
 
 	if (priv->hw_version == MVPP21)
-- 
1.9.1

[PATCH v6 net-next 16/18] net: mvpp2: set 802.3x GoP Flow Control mode

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index afa61cc..7632810 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -6282,7 +6282,7 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
 	old_ctrl4 = ctrl4 = readl(port->base + MVPP22_GMAC_CTRL_4_REG);
 
 	ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
-	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
+	ctrl2 &= ~(MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK | MVPP2_GMAC_FLOW_CTRL_MASK);
 
 	/* Configure port type */
 	if (phy_interface_mode_is_8023z(state->interface)) {
-- 
1.9.1

[PATCH v6 net-next 17/18] net: mvpp2: limit minimum ring size to 1024 descriptors

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

To support Flow Control ring size should be at least 1024 descriptors.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 7632810..98849b0 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -4543,6 +4543,8 @@ static int mvpp2_check_ringparam_valid(struct net_device *dev,
 
 	if (ring->rx_pending > MVPP2_MAX_RXD_MAX)
 		new_rx_pending = MVPP2_MAX_RXD_MAX;
+	else if (ring->rx_pending < MSS_THRESHOLD_START)
+		new_rx_pending = MSS_THRESHOLD_START;
 	else if (!IS_ALIGNED(ring->rx_pending, 16))
 		new_rx_pending = ALIGN(ring->rx_pending, 16);
 
-- 
1.9.1

[PATCH v6 net-next 18/18] net: mvpp2: add TX FC firmware check

[stefanc]

From: Stefan Chulski <stefanc@marvell.com>

Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  1 +
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 42 ++++++++++++++++----
 2 files changed, 36 insertions(+), 7 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 9947385..25013a4 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -829,6 +829,7 @@
 
 #define MSS_THRESHOLD_STOP	768
 #define MSS_THRESHOLD_START	1024
+#define MSS_FC_MAX_TIMEOUT	5000
 
 /* RX buffer constants */
 #define MVPP2_SKB_SHINFO_SIZE \
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index 98849b0..0273134 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -932,6 +932,34 @@ static void mvpp2_bm_pool_update_fc(struct mvpp2_port *port,
 	spin_unlock_irqrestore(&port->priv->mss_spinlock, flags);
 }
 
+static int mvpp2_enable_global_fc(struct mvpp2 *priv)
+{
+	int val, timeout = 0;
+
+	/* Enable global flow control. In this stage global
+	 * flow control enabled, but still disabled per port.
+	 */
+	val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+	val |= FLOW_CONTROL_ENABLE_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	/* Check if Firmware running and disable FC if not*/
+	val |= FLOW_CONTROL_UPDATE_COMMAND_BIT;
+	mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+
+	while (timeout < MSS_FC_MAX_TIMEOUT) {
+		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
+
+		if (!(val & FLOW_CONTROL_UPDATE_COMMAND_BIT))
+			return 0;
+		usleep_range(10, 20);
+		timeout++;
+	}
+
+	priv->global_tx_fc = false;
+	return -EOPNOTSUPP;
+}
+
 /* Release buffer to BM */
 static inline void mvpp2_bm_pool_put(struct mvpp2_port *port, int pool,
 				     dma_addr_t buf_dma_addr,
@@ -7281,7 +7309,7 @@ static int mvpp2_probe(struct platform_device *pdev)
 	struct resource *res;
 	void __iomem *base;
 	int i, shared;
-	int err, val;
+	int err;
 
 	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
@@ -7509,13 +7537,13 @@ static int mvpp2_probe(struct platform_device *pdev)
 		goto err_port_probe;
 	}
 
-	/* Enable global flow control. In this stage global
-	 * flow control enabled, but still disabled per port.
-	 */
 	if (priv->global_tx_fc && priv->hw_version != MVPP21) {
-		val = mvpp2_cm3_read(priv, MSS_FC_COM_REG);
-		val |= FLOW_CONTROL_ENABLE_BIT;
-		mvpp2_cm3_write(priv, MSS_FC_COM_REG, val);
+		err = mvpp2_enable_global_fc(priv);
+		if (err) {
+			dev_warn(&pdev->dev, "CM3 firmware not running, version should be higher than 18.09 ");
+			dev_warn(&pdev->dev, "and chip revision B0\n");
+			dev_warn(&pdev->dev, "Flow control not supported\n");
+		}
 	}
 
 	mvpp2_dbgfs_init(priv, pdev->name);
-- 
1.9.1