[PATCH V9 0/8] Add QSPI and QUPv3 DT nodes for SC7280 SoC

[PATCH V9 0/8] Add QSPI and QUPv3 DT nodes for SC7280 SoC

[Rajesh Patil]

Changes in V9:
 - As per Stephen's comments, 
   1. Moved back qup_opp_table from /soc@0/geniqup@9c0000 to /
   2. changed node names to "qup_spi0_cs_gpio: qup-spi0-cs-gpio" because
      node names should have dashes instead of underscores.

Changes in V8:
 - As per Matthias comments
   Added back qup_spiN_cs_gpio nodes in all spi ports

 - As per Doug comments, Added "qcom,sc7280-qspi" compatible in qspi node

Changes in V7:
 - As per Stephen's comments
   1. Moved qup_opp_table under /soc@0/geniqup@9c0000
   2. Removed qupv3_id_1 in sc7280-idp board file
   3. Sorted alias names for i2c and spi as per alphabet order

 - As per Matthias comment
   Configuring cs pin with gpio (qup_spiN_cs_gpio) definitions are removed

Changes in V6:
 - As per Matthias' comments,
   1. Squashed "Update QUPv3 UART5 DT node" and "Configure debug
      uart for sc7280-idp"
   2. Moved qup_opp_table from /soc to /
   3. Changed convention "clocks" followed by "clock-names"

 - As per Doug comments, added aliases for i2c and spi

Changes in V5:
 - As per Matthias' comments, I've split the patches as below:
   1. Add QSPI node
   2. Configure SPI-NOR FLASH for sc7280-idp
   3. Add QUPv3 wrapper_0 nodes
   4. Update QUPv3 UART5 DT node
   5. Configure debug uart for sc7280-idp
   6. Configure uart7 to support bluetooth on sc7280-idp
   7. Add QUPv3 wrapper_1 nodes

Changes in V4:
 - As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
   qspi_opp_table from /soc to / (root).
 - As per Bjorn's comment, added QUP Wrapper_0 nodes
   as separate patch and debug-uart node as separate patch.
 - Dropped interconnect votes for wrapper_0 and wrapper_1 node
 - Corrected QUP Wrapper_1 SE node's pin control functions like below
        QUP Wrapper_0: SE0-SE7 uses qup00 - qup07 pin-cntrl functions.
        QUP Wrapper_1: SE0-SE7 uses qup10 - qup17 pin-cntrl functions.

Changes in V3:
 - Broken the huge V2 patch into 3 smaller patches.
   1. QSPI DT nodes
   2. QUP wrapper_0 DT nodes
   3. QUP wrapper_1 DT nodes

Changes in V2:
 - As per Doug's comments removed pinmux/pinconf subnodes.
 - As per Doug's comments split of SPI, UART nodes has been done.
 - Moved QSPI node before aps_smmu as per the order.


Rajesh Patil (4):
  dt-bindings: spi: Add sc7280 support
  arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp
  arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp
  arm64: dts: sc7280: Add aliases for I2C and SPI

Roja Rani Yarubandi (4):
  arm64: dts: sc7280: Add QSPI node
  arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes
  arm64: dts: sc7280: Update QUPv3 UART5 DT node
  arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes

 .../bindings/spi/qcom,spi-qcom-qspi.yaml           |    5 +-
 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi           |  125 +-
 arch/arm64/boot/dts/qcom/sc7280.dtsi               | 3196 +++++++++++++++-----
 3 files changed, 2510 insertions(+), 816 deletions(-)

-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 1/8] dt-bindings: spi: Add sc7280 support

[Rajesh Patil]

Add compatible for sc7280 SoC.

Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
---
Changes in V9:
 - No changes

Changes in V8:
 - As per Doug's comments, added "qcom,sc7280-qspi" compatible

 Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
index ef5698f..1c8b2ea 100644
--- a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
@@ -21,7 +21,10 @@ allOf:
 properties:
   compatible:
     items:
-      - const: qcom,sdm845-qspi
+      - enum:
+          - qcom,sdm845-qspi
+          - qcom,sc7280-qspi
+
       - const: qcom,qspi-v1
 
   reg:
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 2/8] arm64: dts: sc7280: Add QSPI node

[Rajesh Patil]

From: Roja Rani Yarubandi <rojay@codeaurora.org>

Add QSPI DT node and qspi_opp_table for SC7280 SoC.

Move qspi_opp_table to / because SPI nodes assume
any child node is a spi device and so we can't put the
table underneath the spi controller.

Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V9:
 - No changes

Changes in V8:
 - As per Doug's comments, Added "qcom,sc7280-qspi" compatible in qspi node

Changes in V6:
 - As per Stephen comments, updated commit message regarding qspi_opp_table
   moved from /soc to /

Changes in V4:
 - As per Stephen's comment updated spi-max-frequency to 37.5MHz, moved
   qspi_opp_table from /soc to / (root).

Changes in V3:
 - Broken the huge V2 patch into 3 smaller patches.
   1. QSPI DT nodes
   2. QUP wrapper_0 DT nodes
   3. QUP wrapper_1 DT nodes

Changes in V2:
 - As per Doug's comments removed pinmux/pinconf subnodes.
 - As per Doug's comments split of SPI, UART nodes has been done.
 - Moved QSPI node before aps_smmu as per the order.

 arch/arm64/boot/dts/qcom/sc7280.dtsi | 61 ++++++++++++++++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index fd78f16..2fbcb0a 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -415,6 +415,25 @@
 		method = "smc";
 	};
 
+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -1318,6 +1337,23 @@
 			};
 		};
 
+		qspi: spi@88dc000 {
+			compatible = "qcom,sc7280-qspi", "qcom,qspi-v1";
+			reg = <0 0x088dc000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				 <&gcc GCC_QSPI_CORE_CLK>;
+			clock-names = "iface", "core";
+			interconnects = <&gem_noc MASTER_APPSS_PROC 0
+					&cnoc2 SLAVE_QSPI_0 0>;
+			interconnect-names = "qspi-config";
+			power-domains = <&rpmhpd SC7280_CX>;
+			operating-points-v2 = <&qspi_opp_table>;
+			status = "disabled";
+		};
+
 		dc_noc: interconnect@90e0000 {
 			reg = <0 0x090e0000 0 0x5080>;
 			compatible = "qcom,sc7280-dc-noc";
@@ -1513,6 +1549,31 @@
 			gpio-ranges = <&tlmm 0 0 175>;
 			wakeup-parent = <&pdc>;
 
+			qspi_clk: qspi-clk {
+				pins = "gpio14";
+				function = "qspi_clk";
+			};
+
+			qspi_cs0: qspi-cs0 {
+				pins = "gpio15";
+				function = "qspi_cs";
+			};
+
+			qspi_cs1: qspi-cs1 {
+				pins = "gpio19";
+				function = "qspi_cs";
+			};
+
+			qspi_data01: qspi-data01 {
+				pins = "gpio12", "gpio13";
+				function = "qspi_data";
+			};
+
+			qspi_data12: qspi-data12 {
+				pins = "gpio16", "gpio17";
+				function = "qspi_data";
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 3/8] arm64: dts: sc7280: Configure SPI-NOR FLASH for sc7280-idp

[Rajesh Patil]

Add spi-nor flash node and pinctrl configurations for the SC7280 IDP.

Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V9:
 - No changes

Changes in V8:
 - No changes

 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 99f9ee5..37b8444 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -211,6 +211,20 @@
 	vcc-supply = <&vreg_l1c_1p8>;
 };
 
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -288,6 +302,19 @@
 
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
+&qspi_cs0 {
+	bias-disable;
+};
+
+&qspi_clk {
+	bias-disable;
+};
+
+&qspi_data01 {
+	/* High-Z when no transfers; nice to park the lines */
+	bias-pull-up;
+};
+
 &qup_uart5_default {
 	tx {
 		pins = "gpio46";
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

[Rajesh Patil]

From: Roja Rani Yarubandi <rojay@codeaurora.org>

Add QUPv3 wrapper_0 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---
Changes in V9:
 - As per Stephen's comments,
   1. Moved back qup_opp_table from /soc@0/geniqup@9c0000 to /
   2. changed node names to "qup_spi0_cs_gpio: qup-spi0-cs-gpio" beacuse
      node names should have dashes instead of underscores.

Changes in V8:
 - As per Matthias' comments, Added back qup_spiN_cs_gpio nodes in all spi ports

Changes in V7:
 - As per Matthias' comments
   Configuring cs pin with gpio (qup_spiN_cs_gpio) definitions are removed.

 - As per Stephen's comments
   Added qup_opp_table under /soc@0/geniqup@9c0000

Changes in V6:
 - As per Matthias' comments,
   1. Changed convention "clocks" followed by "clock-names"
   2. Moved qup_opp_table from /soc to /


 arch/arm64/boot/dts/qcom/sc7280.dtsi | 724 ++++++++++++++++++++++++++++++++++-
 1 file changed, 722 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 2fbcb0a..b65c5da 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -434,6 +434,25 @@
 		};
 	};
 
+	qup_opp_table: qup-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-128000000 {
+			opp-hz = /bits/ 64 <128000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -536,24 +555,425 @@
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
-			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
+			iommus = <&apps_smmu 0x123 0x0>;
 			status = "disabled";
 
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>, <&qup_spi1_cs_gpio>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart1: serial@984000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>, <&qup_spi2_cs_gpio>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart2: serial@988000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>, <&qup_spi3_cs_gpio>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart3: serial@98c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>, <&qup_spi4_cs_gpio>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart4: serial@990000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00994000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00994000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>, <&qup_spi5_cs_gpio>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
 			uart5: serial@994000 {
 				compatible = "qcom,geni-debug-uart";
 				reg = <0 0x00994000 0 0x4000>;
-				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart5_default>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 			};
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>, <&qup_spi6_cs_gpio>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart6: serial@998000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c7: i2c@99c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_data_clk>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi7: spi@99c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>, <&qup_spi7_cs_gpio>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
 		};
 
 		cnoc2: interconnect@1500000 {
@@ -1574,11 +1994,311 @@
 				function = "qspi_data";
 			};
 
+			qup_i2c0_data_clk: qup-i2c0-data-clk {
+				pins = "gpio0", "gpio1";
+				function = "qup00";
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk {
+				pins = "gpio4", "gpio5";
+				function = "qup01";
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk {
+				pins = "gpio8", "gpio9";
+				function = "qup02";
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk {
+				pins = "gpio12", "gpio13";
+				function = "qup03";
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk {
+				pins = "gpio16", "gpio17";
+				function = "qup04";
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk {
+				pins = "gpio20", "gpio21";
+				function = "qup05";
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk {
+				pins = "gpio24", "gpio25";
+				function = "qup06";
+			};
+
+			qup_i2c7_data_clk: qup-i2c7-data-clk {
+				pins = "gpio28", "gpio29";
+				function = "qup07";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup00";
+			};
+
+			qup_spi0_cs: qup-spi0-cs {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_spi0_cs_gpio: qup-spi0-cs-gpio {
+				pins = "gpio3";
+				function = "gpio";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk {
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup01";
+			};
+
+			qup_spi1_cs: qup-spi1-cs {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_spi1_cs_gpio: qup-spi1-cs-gpio {
+				pins = "gpio7";
+				function = "gpio";
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk {
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup02";
+			};
+
+			qup_spi2_cs: qup-spi2-cs {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_spi2_cs_gpio: qup-spi2-cs-gpio {
+				pins = "gpio11";
+				function = "gpio";
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk {
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup03";
+			};
+
+			qup_spi3_cs: qup-spi3-cs {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_spi3_cs_gpio: qup-spi3-cs-gpio {
+				pins = "gpio15";
+				function = "gpio";
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk {
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup04";
+			};
+
+			qup_spi4_cs: qup-spi4-cs {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
+			qup_spi4_cs_gpio: qup-spi4-cs-gpio {
+				pins = "gpio19";
+				function = "gpio";
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk {
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup05";
+			};
+
+			qup_spi5_cs: qup-spi5-cs {
+				pins = "gpio23";
+				function = "qup05";
+			};
+
+			qup_spi5_cs_gpio: qup-spi5-cs-gpio {
+				pins = "gpio23";
+				function = "gpio";
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk {
+				pins = "gpio24", "gpio25", "gpio26";
+				function = "qup06";
+			};
+
+			qup_spi6_cs: qup-spi6-cs {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_spi6_cs_gpio: qup-spi6-cs-gpio {
+				pins = "gpio27";
+				function = "gpio";
+			};
+
+			qup_spi7_data_clk: qup-spi7-data-clk {
+				pins = "gpio28", "gpio29", "gpio30";
+				function = "qup07";
+			};
+
+			qup_spi7_cs: qup-spi7-cs {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
+			qup_spi7_cs_gpio: qup-spi7-cs-gpio {
+				pins = "gpio31";
+				function = "gpio";
+			};
+
+			qup_uart0_cts: qup-uart0-cts {
+				pins = "gpio0";
+				function = "qup00";
+			};
+
+			qup_uart0_rts: qup-uart0-rts {
+				pins = "gpio1";
+				function = "qup00";
+			};
+
+			qup_uart0_tx: qup-uart0-tx {
+				pins = "gpio2";
+				function = "qup00";
+			};
+
+			qup_uart0_rx: qup-uart0-rx {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_uart1_cts: qup-uart1-cts {
+				pins = "gpio4";
+				function = "qup01";
+			};
+
+			qup_uart1_rts: qup-uart1-rts {
+				pins = "gpio5";
+				function = "qup01";
+			};
+
+			qup_uart1_tx: qup-uart1-tx {
+				pins = "gpio6";
+				function = "qup01";
+			};
+
+			qup_uart1_rx: qup-uart1-rx {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_uart2_cts: qup-uart2-cts {
+				pins = "gpio8";
+				function = "qup02";
+			};
+
+			qup_uart2_rts: qup-uart2-rts {
+				pins = "gpio9";
+				function = "qup02";
+			};
+
+			qup_uart2_tx: qup-uart2-tx {
+				pins = "gpio10";
+				function = "qup02";
+			};
+
+			qup_uart2_rx: qup-uart2-rx {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_uart3_cts: qup-uart3-cts {
+				pins = "gpio12";
+				function = "qup03";
+			};
+
+			qup_uart3_rts: qup-uart3-rts {
+				pins = "gpio13";
+				function = "qup03";
+			};
+
+			qup_uart3_tx: qup-uart3-tx {
+				pins = "gpio14";
+				function = "qup03";
+			};
+
+			qup_uart3_rx: qup-uart3-rx {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_uart4_cts: qup-uart4-cts {
+				pins = "gpio16";
+				function = "qup04";
+			};
+
+			qup_uart4_rts: qup-uart4-rts {
+				pins = "gpio17";
+				function = "qup04";
+			};
+
+			qup_uart4_tx: qup-uart4-tx {
+				pins = "gpio18";
+				function = "qup04";
+			};
+
+			qup_uart4_rx: qup-uart4-rx {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
 			qup_uart5_default: qup-uart5-default {
 				pins = "gpio46", "gpio47";
 				function = "qup13";
 			};
 
+			qup_uart6_cts: qup-uart6-cts {
+				pins = "gpio24";
+				function = "qup06";
+			};
+
+			qup_uart6_rts: qup-uart6-rts {
+				pins = "gpio25";
+				function = "qup06";
+			};
+
+			qup_uart6_tx: qup-uart6-tx {
+				pins = "gpio26";
+				function = "qup06";
+			};
+
+			qup_uart6_rx: qup-uart6-rx {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_uart7_cts: qup-uart7-cts {
+				pins = "gpio28";
+				function = "qup07";
+			};
+
+			qup_uart7_rts: qup-uart7-rts {
+				pins = "gpio29";
+				function = "qup07";
+			};
+
+			qup_uart7_tx: qup-uart7-tx {
+				pins = "gpio30";
+				function = "qup07";
+			};
+
+			qup_uart7_rx: qup-uart7-rx {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
 			sdc1_on: sdc1-on {
 				clk {
 					pins = "sdc1_clk";
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 5/8] arm64: dts: sc7280: Update QUPv3 UART5 DT node

[Rajesh Patil]

From: Roja Rani Yarubandi <rojay@codeaurora.org>

Uart5 is treated as dedicated debug uart.Change the
compatible as "qcom,geni-uart" in SoC DT to make it generic
and later update it as "qcom,geni-debug-uart" in sc7280-idp
Add interconnects and power-domains. Split the pinctrl
functions and correct the gpio pins.

Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V9:
 - No changes

Changes in V8:
 - No changes

Changes in V7:
 - As per Matthias comments,
   update commit message regarding UART5 functionality

Changes in V6:
 - As per Matthias' comments,
   Squashed "Update QUPv3 UART5 DT node" and "Configure debug uart for sc7280-idp"


 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 19 ++++++++-----------
 arch/arm64/boot/dts/qcom/sc7280.dtsi     | 30 +++++++++++++++++++++++++-----
 2 files changed, 33 insertions(+), 16 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 37b8444..cf82301 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -258,6 +258,7 @@
 };
 
 &uart5 {
+	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
 
@@ -315,18 +316,14 @@
 	bias-pull-up;
 };
 
-&qup_uart5_default {
-	tx {
-		pins = "gpio46";
-		drive-strength = <2>;
-		bias-disable;
-	};
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
 
-	rx {
-		pins = "gpio47";
-		drive-strength = <2>;
-		bias-pull-up;
-	};
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-pull-up;
 };
 
 &sdc1_on {
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index b65c5da..e1c827c 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -861,13 +861,18 @@
 			};
 
 			uart5: serial@994000 {
-				compatible = "qcom,geni-debug-uart";
+				compatible = "qcom,geni-uart";
 				reg = <0 0x00994000 0 0x4000>;
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				clock-names = "se";
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_uart5_default>;
+				pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
 				status = "disabled";
 			};
 
@@ -2254,9 +2259,24 @@
 				function = "qup04";
 			};
 
-			qup_uart5_default: qup-uart5-default {
-				pins = "gpio46", "gpio47";
-				function = "qup13";
+			qup_uart5_cts: qup-uart5-cts {
+				pins = "gpio20";
+				function = "qup05";
+			};
+
+			qup_uart5_rts: qup-uart5-rts {
+				pins = "gpio21";
+				function = "qup05";
+			};
+
+			qup_uart5_tx: qup-uart5-tx {
+				pins = "gpio22";
+				function = "qup05";
+			};
+
+			qup_uart5_rx: qup-uart5-rx {
+				pins = "gpio23";
+				function = "qup05";
 			};
 
 			qup_uart6_cts: qup-uart6-cts {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 6/8] arm64: dts: sc7280: Configure uart7 to support bluetooth on sc7280-idp

[Rajesh Patil]

Add bluetooth uart pin configuration for sc7280-idp.

Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V9:
 - No changes

Change in V8:
 - No changes

 arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 85 ++++++++++++++++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index cf82301..52638e2 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -301,6 +301,16 @@
 	vdda18-supply = <&vreg_l1c_1p8>;
 };
 
+&uart7 {
+	status = "okay";
+
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
 &qspi_cs0 {
@@ -326,6 +336,81 @@
 	bias-pull-up;
 };
 
+&qup_uart7_cts {
+	/*
+	 * Configure a pull-down on CTS to match the pull of
+	 * the Bluetooth module.
+	 */
+	bias-pull-down;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&tlmm {
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a pull-down on CTS to match the pull of
+		 * the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+};
+
 &sdc1_on {
 	clk {
 		bias-disable;
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 7/8] arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes

[Rajesh Patil]

From: Roja Rani Yarubandi <rojay@codeaurora.org>

Add QUPv3 wrapper_1 DT nodes for SC7280 SoC.

Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V9:
 - As per Stephen's comments,
   changed node names to "qup_spi8_cs_gpio: qup-spi8-cs-gpio" because
   node names should have dashes instead of underscores.

Changes in V8:
 - No changes

Changes in V7:
 - As per Stephen's comments, Removed "status=okay" in qupv3_id_1 for sc7280-idp board file

Changes in V5:
 - As per Matthias' comments, Add QUPv3 wrapper_1 nodes


 arch/arm64/boot/dts/qcom/sc7280.dtsi | 749 +++++++++++++++++++++++++++++++++++
 1 file changed, 749 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index e1c827c..8ebd3ae 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -981,6 +981,435 @@
 			};
 		};
 
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x00ac0000 0 0x2000>;
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			iommus = <&apps_smmu 0x43 0x0>;
+			status = "disabled";
+
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a80000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_data_clk>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi8: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a80000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>, <&qup_spi8_cs_gpio>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart8: serial@a80000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a80000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a84000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi9: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a84000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>, <&qup_spi9_cs_gpio>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart9: serial@a84000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a84000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a88000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi10: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a88000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>, <&qup_spi10_cs_gpio>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart10: serial@a88000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a88000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi11: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>, <&qup_spi11_cs_gpio>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart11: serial@a8c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a90000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_data_clk>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi12: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a90000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>, <&qup_spi12_cs_gpio>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart12: serial@a90000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a90000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_data_clk>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi13: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a94000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>, <&qup_spi13_cs_gpio>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart13: serial@a94000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a94000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_data_clk>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi14: spi@a98000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a98000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>, <&qup_spi14_cs_gpio>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart14: serial@a98000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a98000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c15: i2c@a9c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_data_clk>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi15: spi@a9c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>, <&qup_spi15_cs_gpio>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart15: serial@a9c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+		};
+
 		cnoc2: interconnect@1500000 {
 			reg = <0 0x01500000 0 0x1000>;
 			compatible = "qcom,sc7280-cnoc2";
@@ -2039,6 +2468,46 @@
 				function = "qup07";
 			};
 
+			qup_i2c8_data_clk: qup-i2c8-data-clk {
+				pins = "gpio32", "gpio33";
+				function = "qup10";
+			};
+
+			qup_i2c9_data_clk: qup-i2c9-data-clk {
+				pins = "gpio36", "gpio37";
+				function = "qup11";
+			};
+
+			qup_i2c10_data_clk: qup-i2c10-data-clk {
+				pins = "gpio40", "gpio41";
+				function = "qup12";
+			};
+
+			qup_i2c11_data_clk: qup-i2c11-data-clk {
+				pins = "gpio44", "gpio45";
+				function = "qup13";
+			};
+
+			qup_i2c12_data_clk: qup-i2c12-data-clk {
+				pins = "gpio48", "gpio49";
+				function = "qup14";
+			};
+
+			qup_i2c13_data_clk: qup-i2c13-data-clk {
+				pins = "gpio52", "gpio53";
+				function = "qup15";
+			};
+
+			qup_i2c14_data_clk: qup-i2c14-data-clk {
+				pins = "gpio56", "gpio57";
+				function = "qup16";
+			};
+
+			qup_i2c15_data_clk: qup-i2c15-data-clk {
+				pins = "gpio60", "gpio61";
+				function = "qup17";
+			};
+
 			qup_spi0_data_clk: qup-spi0-data-clk {
 				pins = "gpio0", "gpio1", "gpio2";
 				function = "qup00";
@@ -2159,6 +2628,126 @@
 				function = "gpio";
 			};
 
+			qup_spi8_data_clk: qup-spi8-data-clk {
+				pins = "gpio32", "gpio33", "gpio34";
+				function = "qup10";
+			};
+
+			qup_spi8_cs: qup-spi8-cs {
+				pins = "gpio35";
+				function = "qup10";
+			};
+
+			qup_spi8_cs_gpio: qup-spi8-cs-gpio {
+				pins = "gpio35";
+				function = "gpio";
+			};
+
+			qup_spi9_data_clk: qup-spi9-data-clk {
+				pins = "gpio36", "gpio37", "gpio38";
+				function = "qup11";
+			};
+
+			qup_spi9_cs: qup-spi9-cs {
+				pins = "gpio39";
+				function = "qup11";
+			};
+
+			qup_spi9_cs_gpio: qup-spi9-cs-gpio {
+				pins = "gpio39";
+				function = "gpio";
+			};
+
+			qup_spi10_data_clk: qup-spi10-data-clk {
+				pins = "gpio40", "gpio41", "gpio42";
+				function = "qup12";
+			};
+
+			qup_spi10_cs: qup-spi10-cs {
+				pins = "gpio43";
+				function = "qup12";
+			};
+
+			qup_spi10_cs_gpio: qup-spi10-cs-gpio {
+				pins = "gpio43";
+				function = "gpio";
+			};
+
+			qup_spi11_data_clk: qup-spi11-data-clk {
+				pins = "gpio44", "gpio45", "gpio46";
+				function = "qup13";
+			};
+
+			qup_spi11_cs: qup-spi11-cs {
+				pins = "gpio47";
+				function = "qup13";
+			};
+
+			qup_spi11_cs_gpio: qup-spi11-cs-gpio {
+				pins = "gpio47";
+				function = "gpio";
+			};
+
+			qup_spi12_data_clk: qup-spi12-data-clk {
+				pins = "gpio48", "gpio49", "gpio50";
+				function = "qup14";
+			};
+
+			qup_spi12_cs: qup-spi12-cs {
+				pins = "gpio51";
+				function = "qup14";
+			};
+
+			qup_spi12_cs_gpio: qup-spi12-cs-gpio {
+				pins = "gpio51";
+				function = "gpio";
+			};
+
+			qup_spi13_data_clk: qup-spi13-data-clk {
+				pins = "gpio52", "gpio53", "gpio54";
+				function = "qup15";
+			};
+
+			qup_spi13_cs: qup-spi13-cs {
+				pins = "gpio55";
+				function = "qup15";
+			};
+
+			qup_spi13_cs_gpio: qup-spi13-cs-gpio {
+				pins = "gpio55";
+				function = "gpio";
+			};
+
+			qup_spi14_data_clk: qup-spi14-data-clk {
+				pins = "gpio56", "gpio57", "gpio58";
+				function = "qup16";
+			};
+
+			qup_spi14_cs: qup-spi14-cs {
+				pins = "gpio59";
+				function = "qup16";
+			};
+
+			qup_spi14_cs_gpio: qup-spi14-cs-gpio {
+				pins = "gpio59";
+				function = "gpio";
+			};
+
+			qup_spi15_data_clk: qup-spi15-data-clk {
+				pins = "gpio60", "gpio61", "gpio62";
+				function = "qup17";
+			};
+
+			qup_spi15_cs: qup-spi15-cs {
+				pins = "gpio63";
+				function = "qup17";
+			};
+
+			qup_spi15_cs_gpio: qup-spi15-cs-gpio {
+				pins = "gpio63";
+				function = "gpio";
+			};
+
 			qup_uart0_cts: qup-uart0-cts {
 				pins = "gpio0";
 				function = "qup00";
@@ -2399,6 +2988,166 @@
 					bias-bus-hold;
 				};
 			};
+
+			qup_uart8_cts: qup-uart8-cts {
+				pins = "gpio32";
+				function = "qup10";
+			};
+
+			qup_uart8_rts: qup-uart8-rts {
+				pins = "gpio33";
+				function = "qup10";
+			};
+
+			qup_uart8_tx: qup-uart8-tx {
+				pins = "gpio34";
+				function = "qup10";
+			};
+
+			qup_uart8_rx: qup-uart8-rx {
+				pins = "gpio35";
+				function = "qup10";
+			};
+
+			qup_uart9_cts: qup-uart9-cts {
+				pins = "gpio36";
+				function = "qup11";
+			};
+
+			qup_uart9_rts: qup-uart9-rts {
+				pins = "gpio37";
+				function = "qup11";
+			};
+
+			qup_uart9_tx: qup-uart9-tx {
+				pins = "gpio38";
+				function = "qup11";
+			};
+
+			qup_uart9_rx: qup-uart9-rx {
+				pins = "gpio39";
+				function = "qup11";
+			};
+
+			qup_uart10_cts: qup-uart10-cts {
+				pins = "gpio40";
+				function = "qup12";
+			};
+
+			qup_uart10_rts: qup-uart10-rts {
+				pins = "gpio41";
+				function = "qup12";
+			};
+
+			qup_uart10_tx: qup-uart10-tx {
+				pins = "gpio42";
+				function = "qup12";
+			};
+
+			qup_uart10_rx: qup-uart10-rx {
+				pins = "gpio43";
+				function = "qup12";
+			};
+
+			qup_uart11_cts: qup-uart11-cts {
+				pins = "gpio44";
+				function = "qup13";
+			};
+
+			qup_uart11_rts: qup-uart11-rts {
+				pins = "gpio45";
+				function = "qup13";
+			};
+
+			qup_uart11_tx: qup-uart11-tx {
+				pins = "gpio46";
+				function = "qup13";
+			};
+
+			qup_uart11_rx: qup-uart11-rx {
+				pins = "gpio47";
+				function = "qup13";
+			};
+
+			qup_uart12_cts: qup-uart12-cts {
+				pins = "gpio48";
+				function = "qup14";
+			};
+
+			qup_uart12_rts: qup-uart12-rts {
+				pins = "gpio49";
+				function = "qup14";
+			};
+
+			qup_uart12_tx: qup-uart12-tx {
+				pins = "gpio50";
+				function = "qup14";
+			};
+
+			qup_uart12_rx: qup-uart12-rx {
+				pins = "gpio51";
+				function = "qup14";
+			};
+
+			qup_uart13_cts: qup-uart13-cts {
+				pins = "gpio52";
+				function = "qup15";
+			};
+
+			qup_uart13_rts: qup-uart13-rts {
+				pins = "gpio53";
+				function = "qup15";
+			};
+
+			qup_uart13_tx: qup-uart13-tx {
+				pins = "gpio54";
+				function = "qup15";
+			};
+
+			qup_uart13_rx: qup-uart13-rx {
+				pins = "gpio55";
+				function = "qup15";
+			};
+
+			qup_uart14_cts: qup-uart14-cts {
+				pins = "gpio56";
+				function = "qup16";
+			};
+
+			qup_uart14_rts: qup-uart14-rts {
+				pins = "gpio57";
+				function = "qup16";
+			};
+
+			qup_uart14_tx: qup-uart14-tx {
+				pins = "gpio58";
+				function = "qup16";
+			};
+
+			qup_uart14_rx: qup-uart14-rx {
+				pins = "gpio59";
+				function = "qup16";
+			};
+
+			qup_uart15_cts: qup-uart15-cts {
+				pins = "gpio60";
+				function = "qup17";
+			};
+
+			qup_uart15_rts: qup-uart15-rts {
+				pins = "gpio61";
+				function = "qup17";
+			};
+
+			qup_uart15_tx: qup-uart15-tx {
+				pins = "gpio62";
+				function = "qup17";
+			};
+
+			qup_uart15_rx: qup-uart15-rx {
+				pins = "gpio63";
+				function = "qup17";
+			};
 		};
 
 		apps_smmu: iommu@15000000 {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

[PATCH V9 8/8] arm64: dts: sc7280: Add aliases for I2C and SPI

[Rajesh Patil]

Add aliases for i2c and spi for sc7280 soc.

Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
---
Changes in V9:
 - No changes

Changes in V8:
 - No changes

Changes in V7:
 - As per Stephen's comments, Sorted alias names for i2c and spi as per alphabet order

Changes in V6:
 - As per Doug's comments, added aliases for i2c and spi


 arch/arm64/boot/dts/qcom/sc7280.dtsi | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 8ebd3ae..7a0102c 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -26,8 +26,40 @@
 	chosen { };
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
 		mmc1 = &sdhc_1;
 		mmc2 = &sdhc_2;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		spi4 = &spi4;
+		spi5 = &spi5;
+		spi6 = &spi6;
+		spi7 = &spi7;
+		spi8 = &spi8;
+		spi9 = &spi9;
+		spi10 = &spi10;
+		spi11 = &spi11;
+		spi12 = &spi12;
+		spi13 = &spi13;
+		spi14 = &spi14;
+		spi15 = &spi15;
 	};
 
 	clocks {
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member 
of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH V9 1/8] dt-bindings: spi: Add sc7280 support

[Stephen Boyd]

Quoting Rajesh Patil (2021-09-21 03:38:59)
> Add compatible for sc7280 SoC.
> 
> Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
> Reviewed-by: Doug Anderson <dianders@chromium.org>
> ---

One nit below

Reviewed-by: Stephen Boyd <swboyd@chromium.org>

> diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
> index ef5698f..1c8b2ea 100644
> --- a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
> +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
> @@ -21,7 +21,10 @@ allOf:
>  properties:
>    compatible:
>      items:
> -      - const: qcom,sdm845-qspi
> +      - enum:
> +          - qcom,sdm845-qspi
> +          - qcom,sc7280-qspi

Would be nice to keep this alphabet sorted too.

> +
>        - const: qcom,qspi-v1
>  
>    reg:

Re: [PATCH V9 4/8] arm64: dts: sc7280: Add QUPv3 wrapper_0 nodes

[Stephen Boyd]

Quoting Rajesh Patil (2021-09-21 03:39:02)
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index 2fbcb0a..b65c5da 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -536,24 +555,425 @@
>                 qupv3_id_0: geniqup@9c0000 {
>                         compatible = "qcom,geni-se-qup";
>                         reg = <0 0x009c0000 0 0x2000>;
> -                       clock-names = "m-ahb", "s-ahb";
>                         clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
>                                  <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
> +                       clock-names = "m-ahb", "s-ahb";
>                         #address-cells = <2>;
>                         #size-cells = <2>;
>                         ranges;
> +                       iommus = <&apps_smmu 0x123 0x0>;
>                         status = "disabled";
>
> +                       i2c0: i2c@980000 {
> +                               compatible = "qcom,geni-i2c";
> +                               reg = <0 0x00980000 0 0x4000>;
> +                               clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> +                               clock-names = "se";
> +                               pinctrl-names = "default";
> +                               pinctrl-0 = <&qup_i2c0_data_clk>;
> +                               interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
> +                                               <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
> +                                               <&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
> +                               interconnect-names = "qup-core", "qup-config",
> +                                                       "qup-memory";
> +                               status = "disabled";
> +                       };
> +
> +                       spi0: spi@980000 {
> +                               compatible = "qcom,geni-spi";
> +                               reg = <0 0x00980000 0 0x4000>;
> +                               clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
> +                               clock-names = "se";
> +                               pinctrl-names = "default";
> +                               pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>, <&qup_spi0_cs_gpio>;

This should only have qup_spi0_data_clk and qup_spi0_cs, not
qup_spi0_cs_gpio. Both qup controlled and gpio controlled options are
provided in case a board wants to use the qup version of chipselect, but
having them both used by default leads to conflicts and confusion. This
same comment applies to all spi pinctrl properties in this file. Please
keep the cs_gpio variants though so that boards can use them if they
want. They will be unused, but that's OK.

> +                               interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               power-domains = <&rpmhpd SC7280_CX>;
> +                               operating-points-v2 = <&qup_opp_table>;
> +                               interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
> +                                               <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
> +                               interconnect-names = "qup-core", "qup-config";
> +                               status = "disabled";
> +                       };
> +

Re: [PATCH V9 7/8] arm64: dts: sc7280: Add QUPv3 wrapper_1 nodes

[Stephen Boyd]

Quoting Rajesh Patil (2021-09-21 03:39:05)
> From: Roja Rani Yarubandi <rojay@codeaurora.org>
>
> Add QUPv3 wrapper_1 DT nodes for SC7280 SoC.
>
> Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
> Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
> Reviewed-by: Stephen Boyd <swboyd@chromium.org>

Same comment here. Please make the cs_gpio nodes unused.

Re: [PATCH V9 1/8] dt-bindings: spi: Add sc7280 support

[rajpat]

On 2021-09-21 23:41, Stephen Boyd wrote:
> Quoting Rajesh Patil (2021-09-21 03:38:59)
>> Add compatible for sc7280 SoC.
>> 
>> Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
>> Reviewed-by: Doug Anderson <dianders@chromium.org>
>> ---
> 
> One nit below
> 
> Reviewed-by: Stephen Boyd <swboyd@chromium.org>
> 
>> diff --git 
>> a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml 
>> b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
>> index ef5698f..1c8b2ea 100644
>> --- a/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
>> +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qcom-qspi.yaml
>> @@ -21,7 +21,10 @@ allOf:
>>  properties:
>>    compatible:
>>      items:
>> -      - const: qcom,sdm845-qspi
>> +      - enum:
>> +          - qcom,sdm845-qspi
>> +          - qcom,sc7280-qspi
> 
> Would be nice to keep this alphabet sorted too.

Okay. I will keep in alphabet order.

> 
>> +
>>        - const: qcom,qspi-v1
>> 
>>    reg: