All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-08-29  5:00 ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-08-29  5:00 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Heiko Stuebner
  Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
	phone-devel, Tom Fitzhenry

PinePhone Pro is a RK3399 based phone produced by Pine64.

Add a basic DTS for it. This is a working base that will allow myself and
others to add more nodes.

Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].

dtbs_check found some violations, but they were all common to the
rk3399.dtsi (and thus occurred on other RK3399 SoC DTs).

0. https://lore.kernel.org/all/20220815123004.252014-2-tom@tom-fitzhenry.me.uk/

Changes since v4:
* Add regulator vcc1v8_codec.
* Un-enable unused regulators for codec and touch.
* Fix voltage ranges on vdd_center and vccio_sd.
* Un-modify unused gpu_opp_table.

Changes since v3:
* Fix regulator min/max voltages, to align with RK3399-T datasheet.
* Re-enable cluster1_opp/opp06, with freq/volts as per RK3399-T datasheet.
* Fix gpu_opp_table voltages to align with RK3399-T datasheet.
* Change regulator names, to align with PinePhone Pro datasheet.
* Use DT Generic Names Recommendation: power -> key-power.
* Remove unused label vcc_wl on regulator.
* Fix code style.

Changes since v2:
* Used rk3399-opp.dtsi (+ disabled) rather than introdu4cing rk3399-t-opp.dtsi
* Removed superfluous comments.
* Followed DT Generic Names Recommendation
* Set 'From:' of DTS patch to be Martijn, the primary contributor to the DT.

Changes since v1:
* Simplified the DT to a minimal base.
* Introduced the RK3399-T OPPs.

Martijn Braam (1):
  arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro

 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3399-pinephone-pro.dts     | 398 ++++++++++++++++++
 2 files changed, 399 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts


base-commit: 2e1170c71ec0c0fb785ce76fca7c682e930af2b8
prerequisite-patch-id: 41a5419f57b2712f7127d5c6cf1dbf062f6570da
-- 
2.37.1


^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-08-29  5:00 ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-08-29  5:00 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Heiko Stuebner
  Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
	phone-devel, Tom Fitzhenry

PinePhone Pro is a RK3399 based phone produced by Pine64.

Add a basic DTS for it. This is a working base that will allow myself and
others to add more nodes.

Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].

dtbs_check found some violations, but they were all common to the
rk3399.dtsi (and thus occurred on other RK3399 SoC DTs).

0. https://lore.kernel.org/all/20220815123004.252014-2-tom@tom-fitzhenry.me.uk/

Changes since v4:
* Add regulator vcc1v8_codec.
* Un-enable unused regulators for codec and touch.
* Fix voltage ranges on vdd_center and vccio_sd.
* Un-modify unused gpu_opp_table.

Changes since v3:
* Fix regulator min/max voltages, to align with RK3399-T datasheet.
* Re-enable cluster1_opp/opp06, with freq/volts as per RK3399-T datasheet.
* Fix gpu_opp_table voltages to align with RK3399-T datasheet.
* Change regulator names, to align with PinePhone Pro datasheet.
* Use DT Generic Names Recommendation: power -> key-power.
* Remove unused label vcc_wl on regulator.
* Fix code style.

Changes since v2:
* Used rk3399-opp.dtsi (+ disabled) rather than introdu4cing rk3399-t-opp.dtsi
* Removed superfluous comments.
* Followed DT Generic Names Recommendation
* Set 'From:' of DTS patch to be Martijn, the primary contributor to the DT.

Changes since v1:
* Simplified the DT to a minimal base.
* Introduced the RK3399-T OPPs.

Martijn Braam (1):
  arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro

 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3399-pinephone-pro.dts     | 398 ++++++++++++++++++
 2 files changed, 399 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts


base-commit: 2e1170c71ec0c0fb785ce76fca7c682e930af2b8
prerequisite-patch-id: 41a5419f57b2712f7127d5c6cf1dbf062f6570da
-- 
2.37.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-08-29  5:00 ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-08-29  5:00 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Heiko Stuebner
  Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
	phone-devel, Tom Fitzhenry

PinePhone Pro is a RK3399 based phone produced by Pine64.

Add a basic DTS for it. This is a working base that will allow myself and
others to add more nodes.

Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].

dtbs_check found some violations, but they were all common to the
rk3399.dtsi (and thus occurred on other RK3399 SoC DTs).

0. https://lore.kernel.org/all/20220815123004.252014-2-tom@tom-fitzhenry.me.uk/

Changes since v4:
* Add regulator vcc1v8_codec.
* Un-enable unused regulators for codec and touch.
* Fix voltage ranges on vdd_center and vccio_sd.
* Un-modify unused gpu_opp_table.

Changes since v3:
* Fix regulator min/max voltages, to align with RK3399-T datasheet.
* Re-enable cluster1_opp/opp06, with freq/volts as per RK3399-T datasheet.
* Fix gpu_opp_table voltages to align with RK3399-T datasheet.
* Change regulator names, to align with PinePhone Pro datasheet.
* Use DT Generic Names Recommendation: power -> key-power.
* Remove unused label vcc_wl on regulator.
* Fix code style.

Changes since v2:
* Used rk3399-opp.dtsi (+ disabled) rather than introdu4cing rk3399-t-opp.dtsi
* Removed superfluous comments.
* Followed DT Generic Names Recommendation
* Set 'From:' of DTS patch to be Martijn, the primary contributor to the DT.

Changes since v1:
* Simplified the DT to a minimal base.
* Introduced the RK3399-T OPPs.

Martijn Braam (1):
  arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro

 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3399-pinephone-pro.dts     | 398 ++++++++++++++++++
 2 files changed, 399 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts


base-commit: 2e1170c71ec0c0fb785ce76fca7c682e930af2b8
prerequisite-patch-id: 41a5419f57b2712f7127d5c6cf1dbf062f6570da
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 12+ messages in thread

* [PATCH v5 1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
  2022-08-29  5:00 ` Tom Fitzhenry
  (?)
@ 2022-08-29  5:00   ` Tom Fitzhenry
  -1 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-08-29  5:00 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Heiko Stuebner
  Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
	phone-devel, Martijn Braam, Kamil Trzciński, Ondrej Jirman,
	Tom Fitzhenry, Caleb Connolly, Nícolas F . R . A . Prado

From: Martijn Braam <martijn@brixit.nl>

This is a basic DT containing regulators and UART, intended to be a
base that myself and others can add additional nodes in future patches.

Tested to work: booting from eMMC/SD, output over UART.

https://wiki.pine64.org/wiki/PinePhone_Pro

This is derived from the community pine64-org repo[0] with fixes from
https://megous.com/git/linux.

0. https://gitlab.com/pine64-org/linux/-/commit/261d3b5f8ac503f97da810986d1d6422430c8531

Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted]
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Tested-by: Nícolas F. R. A. Prado <n@nfraprado.net>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3399-pinephone-pro.dts     | 398 ++++++++++++++++++
 2 files changed, 399 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ef79a672804a..cb42e0a15808 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
new file mode 100644
index 000000000000..f00c80361377
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Martijn Braam <martijn@brixit.nl>
+ * Copyright (c) 2021 Kamil Trzciński <ayufan@ayufan.eu>
+ */
+
+/*
+ * PinePhone Pro datasheet:
+ * https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Pine64 PinePhonePro";
+	compatible = "pine64,pinephone-pro", "rockchip,rk3399";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdio0;
+		mmc1 = &sdmmc;
+		mmc2 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn_pin>;
+
+		key-power {
+			debounce-interval = <20>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcca1v8_s3: vcc1v8-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca1v8_s3";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc1v8_codec: vcc1v8-codec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc1v8_codec_en>;
+		regulator-name = "vcc1v8_codec";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk818: pmic@1c {
+		compatible = "rockchip,rk818";
+		reg = <0x1c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_cpu_l: DCDC_REG1 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <875000>;
+				regulator-max-microvolt = <975000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_center: DCDC_REG2 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG1 {
+				regulator-name = "vcca3v0_codec";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcc3v0_touch: LDO_REG2 {
+				regulator-name = "vcc3v0_touch";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcca1v8_codec: LDO_REG3 {
+				regulator-name = "vcca1v8_codec";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			rk818_pwr_on: LDO_REG4 {
+				regulator-name = "rk818_pwr_on";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG5 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG7 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcc3v3_s3: LDO_REG8 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG9 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <3150000>;
+			};
+
+			vcc3v3_s0: SWITCH_REG {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_pin>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_pin>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <975000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&cluster0_opp {
+	opp04 {
+		status = "disabled";
+	};
+
+	opp05 {
+		status = "disabled";
+	};
+};
+
+&cluster1_opp {
+	opp06 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1100000 1100000 1150000>;
+	};
+
+	opp07 {
+		status = "disabled";
+	};
+};
+
+&io_domains {
+	bt656-supply = <&vcc1v8_dvp>;
+	audio-supply = <&vcca1v8_codec>;
+	sdmmc-supply = <&vccio_sd>;
+	gpio1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&pinctrl {
+	buttons {
+		pwrbtn_pin: pwrbtn-pin {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_pin: vsel1-pin {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_pin: vsel2-pin {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sound {
+		vcc1v8_codec_en: vcc1v8-codec-en {
+			rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
-- 
2.37.1


^ permalink raw reply related	[flat|nested] 12+ messages in thread

* [PATCH v5 1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
@ 2022-08-29  5:00   ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-08-29  5:00 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Heiko Stuebner
  Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
	phone-devel, Martijn Braam, Kamil Trzciński, Ondrej Jirman,
	Tom Fitzhenry, Caleb Connolly, Nícolas F . R . A . Prado

From: Martijn Braam <martijn@brixit.nl>

This is a basic DT containing regulators and UART, intended to be a
base that myself and others can add additional nodes in future patches.

Tested to work: booting from eMMC/SD, output over UART.

https://wiki.pine64.org/wiki/PinePhone_Pro

This is derived from the community pine64-org repo[0] with fixes from
https://megous.com/git/linux.

0. https://gitlab.com/pine64-org/linux/-/commit/261d3b5f8ac503f97da810986d1d6422430c8531

Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted]
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Tested-by: Nícolas F. R. A. Prado <n@nfraprado.net>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3399-pinephone-pro.dts     | 398 ++++++++++++++++++
 2 files changed, 399 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ef79a672804a..cb42e0a15808 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
new file mode 100644
index 000000000000..f00c80361377
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Martijn Braam <martijn@brixit.nl>
+ * Copyright (c) 2021 Kamil Trzciński <ayufan@ayufan.eu>
+ */
+
+/*
+ * PinePhone Pro datasheet:
+ * https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Pine64 PinePhonePro";
+	compatible = "pine64,pinephone-pro", "rockchip,rk3399";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdio0;
+		mmc1 = &sdmmc;
+		mmc2 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn_pin>;
+
+		key-power {
+			debounce-interval = <20>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcca1v8_s3: vcc1v8-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca1v8_s3";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc1v8_codec: vcc1v8-codec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc1v8_codec_en>;
+		regulator-name = "vcc1v8_codec";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk818: pmic@1c {
+		compatible = "rockchip,rk818";
+		reg = <0x1c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_cpu_l: DCDC_REG1 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <875000>;
+				regulator-max-microvolt = <975000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_center: DCDC_REG2 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG1 {
+				regulator-name = "vcca3v0_codec";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcc3v0_touch: LDO_REG2 {
+				regulator-name = "vcc3v0_touch";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcca1v8_codec: LDO_REG3 {
+				regulator-name = "vcca1v8_codec";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			rk818_pwr_on: LDO_REG4 {
+				regulator-name = "rk818_pwr_on";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG5 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG7 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcc3v3_s3: LDO_REG8 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG9 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <3150000>;
+			};
+
+			vcc3v3_s0: SWITCH_REG {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_pin>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_pin>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <975000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&cluster0_opp {
+	opp04 {
+		status = "disabled";
+	};
+
+	opp05 {
+		status = "disabled";
+	};
+};
+
+&cluster1_opp {
+	opp06 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1100000 1100000 1150000>;
+	};
+
+	opp07 {
+		status = "disabled";
+	};
+};
+
+&io_domains {
+	bt656-supply = <&vcc1v8_dvp>;
+	audio-supply = <&vcca1v8_codec>;
+	sdmmc-supply = <&vccio_sd>;
+	gpio1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&pinctrl {
+	buttons {
+		pwrbtn_pin: pwrbtn-pin {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_pin: vsel1-pin {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_pin: vsel2-pin {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sound {
+		vcc1v8_codec_en: vcc1v8-codec-en {
+			rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
-- 
2.37.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

^ permalink raw reply related	[flat|nested] 12+ messages in thread

* [PATCH v5 1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
@ 2022-08-29  5:00   ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-08-29  5:00 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Heiko Stuebner
  Cc: devicetree, linux-arm-kernel, linux-rockchip, linux-kernel,
	phone-devel, Martijn Braam, Kamil Trzciński, Ondrej Jirman,
	Tom Fitzhenry, Caleb Connolly, Nícolas F . R . A . Prado

From: Martijn Braam <martijn@brixit.nl>

This is a basic DT containing regulators and UART, intended to be a
base that myself and others can add additional nodes in future patches.

Tested to work: booting from eMMC/SD, output over UART.

https://wiki.pine64.org/wiki/PinePhone_Pro

This is derived from the community pine64-org repo[0] with fixes from
https://megous.com/git/linux.

0. https://gitlab.com/pine64-org/linux/-/commit/261d3b5f8ac503f97da810986d1d6422430c8531

Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted]
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Tested-by: Nícolas F. R. A. Prado <n@nfraprado.net>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3399-pinephone-pro.dts     | 398 ++++++++++++++++++
 2 files changed, 399 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ef79a672804a..cb42e0a15808 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
new file mode 100644
index 000000000000..f00c80361377
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Martijn Braam <martijn@brixit.nl>
+ * Copyright (c) 2021 Kamil Trzciński <ayufan@ayufan.eu>
+ */
+
+/*
+ * PinePhone Pro datasheet:
+ * https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Pine64 PinePhonePro";
+	compatible = "pine64,pinephone-pro", "rockchip,rk3399";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdio0;
+		mmc1 = &sdmmc;
+		mmc2 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn_pin>;
+
+		key-power {
+			debounce-interval = <20>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcca1v8_s3: vcc1v8-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca1v8_s3";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc1v8_codec: vcc1v8-codec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc1v8_codec_en>;
+		regulator-name = "vcc1v8_codec";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk818: pmic@1c {
+		compatible = "rockchip,rk818";
+		reg = <0x1c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_cpu_l: DCDC_REG1 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <875000>;
+				regulator-max-microvolt = <975000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_center: DCDC_REG2 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG1 {
+				regulator-name = "vcca3v0_codec";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcc3v0_touch: LDO_REG2 {
+				regulator-name = "vcc3v0_touch";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcca1v8_codec: LDO_REG3 {
+				regulator-name = "vcca1v8_codec";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			rk818_pwr_on: LDO_REG4 {
+				regulator-name = "rk818_pwr_on";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG5 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG7 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcc3v3_s3: LDO_REG8 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG9 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <3150000>;
+			};
+
+			vcc3v3_s0: SWITCH_REG {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_pin>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_pin>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <975000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&cluster0_opp {
+	opp04 {
+		status = "disabled";
+	};
+
+	opp05 {
+		status = "disabled";
+	};
+};
+
+&cluster1_opp {
+	opp06 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1100000 1100000 1150000>;
+	};
+
+	opp07 {
+		status = "disabled";
+	};
+};
+
+&io_domains {
+	bt656-supply = <&vcc1v8_dvp>;
+	audio-supply = <&vcca1v8_codec>;
+	sdmmc-supply = <&vccio_sd>;
+	gpio1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&pinctrl {
+	buttons {
+		pwrbtn_pin: pwrbtn-pin {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_pin: vsel1-pin {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_pin: vsel2-pin {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sound {
+		vcc1v8_codec_en: vcc1v8-codec-en {
+			rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
-- 
2.37.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 12+ messages in thread

* Re: [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
  2022-08-29  5:00 ` Tom Fitzhenry
  (?)
@ 2022-09-04 17:22   ` Heiko Stuebner
  -1 siblings, 0 replies; 12+ messages in thread
From: Heiko Stuebner @ 2022-09-04 17:22 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Tom Fitzhenry
  Cc: Heiko Stuebner, phone-devel, linux-rockchip, devicetree,
	linux-kernel, linux-arm-kernel

On Mon, 29 Aug 2022 15:00:39 +1000, Tom Fitzhenry wrote:
> PinePhone Pro is a RK3399 based phone produced by Pine64.
> 
> Add a basic DTS for it. This is a working base that will allow myself and
> others to add more nodes.
> 
> Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].
> 
> [...]

Applied, thanks!

[1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
      commit: 78a21c7d59520e72ebea667fe8745a4371d9fe86


Why was the dt-binding addition missing?
I've pulled the binding from v3 now.

While it is true that you should not resend patches just to add Acks,
when re-sending a whole series that includes other changes it's still
necessary to keep all patches together ;-)


Best regards,
-- 
Heiko Stuebner <heiko@sntech.de>

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-09-04 17:22   ` Heiko Stuebner
  0 siblings, 0 replies; 12+ messages in thread
From: Heiko Stuebner @ 2022-09-04 17:22 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Tom Fitzhenry
  Cc: Heiko Stuebner, phone-devel, linux-rockchip, devicetree,
	linux-kernel, linux-arm-kernel

On Mon, 29 Aug 2022 15:00:39 +1000, Tom Fitzhenry wrote:
> PinePhone Pro is a RK3399 based phone produced by Pine64.
> 
> Add a basic DTS for it. This is a working base that will allow myself and
> others to add more nodes.
> 
> Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].
> 
> [...]

Applied, thanks!

[1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
      commit: 78a21c7d59520e72ebea667fe8745a4371d9fe86


Why was the dt-binding addition missing?
I've pulled the binding from v3 now.

While it is true that you should not resend patches just to add Acks,
when re-sending a whole series that includes other changes it's still
necessary to keep all patches together ;-)


Best regards,
-- 
Heiko Stuebner <heiko@sntech.de>

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-09-04 17:22   ` Heiko Stuebner
  0 siblings, 0 replies; 12+ messages in thread
From: Heiko Stuebner @ 2022-09-04 17:22 UTC (permalink / raw)
  To: Rob Herring, Krzysztof Kozlowski, Tom Fitzhenry
  Cc: Heiko Stuebner, phone-devel, linux-rockchip, devicetree,
	linux-kernel, linux-arm-kernel

On Mon, 29 Aug 2022 15:00:39 +1000, Tom Fitzhenry wrote:
> PinePhone Pro is a RK3399 based phone produced by Pine64.
> 
> Add a basic DTS for it. This is a working base that will allow myself and
> others to add more nodes.
> 
> Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].
> 
> [...]

Applied, thanks!

[1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
      commit: 78a21c7d59520e72ebea667fe8745a4371d9fe86


Why was the dt-binding addition missing?
I've pulled the binding from v3 now.

While it is true that you should not resend patches just to add Acks,
when re-sending a whole series that includes other changes it's still
necessary to keep all patches together ;-)


Best regards,
-- 
Heiko Stuebner <heiko@sntech.de>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
  2022-09-04 17:22   ` Heiko Stuebner
  (?)
@ 2022-09-05 21:00     ` Tom Fitzhenry
  -1 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-09-05 21:00 UTC (permalink / raw)
  To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
  Cc: phone-devel, linux-rockchip, devicetree, linux-kernel, linux-arm-kernel

On 5/9/22 03:22, Heiko Stuebner wrote:
> On Mon, 29 Aug 2022 15:00:39 +1000, Tom Fitzhenry wrote:
>> PinePhone Pro is a RK3399 based phone produced by Pine64.
>>
>> Add a basic DTS for it. This is a working base that will allow myself and
>> others to add more nodes.
>>
>> Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].
>>
>> [...]
> 
> Applied, thanks!
> 
> [1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
>        commit: 78a21c7d59520e72ebea667fe8745a4371d9fe86
> 
> 
> Why was the dt-binding addition missing?
> I've pulled the binding from v3 now.
> 
> While it is true that you should not resend patches just to add Acks,
> when re-sending a whole series that includes other changes it's still
> necessary to keep all patches together ;-)

Ah, I had misinterpreted previous advice on when it was necessary to 
repost patches.

I did wonder how maintainers would then discover the set of patches, and 
so included the "Relies on [..." text above.

I will ensure patch series are complete in future.

Thanks for your patience and review! :)

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-09-05 21:00     ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-09-05 21:00 UTC (permalink / raw)
  To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
  Cc: phone-devel, linux-rockchip, devicetree, linux-kernel, linux-arm-kernel

On 5/9/22 03:22, Heiko Stuebner wrote:
> On Mon, 29 Aug 2022 15:00:39 +1000, Tom Fitzhenry wrote:
>> PinePhone Pro is a RK3399 based phone produced by Pine64.
>>
>> Add a basic DTS for it. This is a working base that will allow myself and
>> others to add more nodes.
>>
>> Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].
>>
>> [...]
> 
> Applied, thanks!
> 
> [1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
>        commit: 78a21c7d59520e72ebea667fe8745a4371d9fe86
> 
> 
> Why was the dt-binding addition missing?
> I've pulled the binding from v3 now.
> 
> While it is true that you should not resend patches just to add Acks,
> when re-sending a whole series that includes other changes it's still
> necessary to keep all patches together ;-)

Ah, I had misinterpreted previous advice on when it was necessary to 
repost patches.

I did wonder how maintainers would then discover the set of patches, and 
so included the "Relies on [..." text above.

I will ensure patch series are complete in future.

Thanks for your patience and review! :)

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

^ permalink raw reply	[flat|nested] 12+ messages in thread

* Re: [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone
@ 2022-09-05 21:00     ` Tom Fitzhenry
  0 siblings, 0 replies; 12+ messages in thread
From: Tom Fitzhenry @ 2022-09-05 21:00 UTC (permalink / raw)
  To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski
  Cc: phone-devel, linux-rockchip, devicetree, linux-kernel, linux-arm-kernel

On 5/9/22 03:22, Heiko Stuebner wrote:
> On Mon, 29 Aug 2022 15:00:39 +1000, Tom Fitzhenry wrote:
>> PinePhone Pro is a RK3399 based phone produced by Pine64.
>>
>> Add a basic DTS for it. This is a working base that will allow myself and
>> others to add more nodes.
>>
>> Relies on "dt-bindings: arm: rockchip: Add PinePhone Pro bindings"[0].
>>
>> [...]
> 
> Applied, thanks!
> 
> [1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro
>        commit: 78a21c7d59520e72ebea667fe8745a4371d9fe86
> 
> 
> Why was the dt-binding addition missing?
> I've pulled the binding from v3 now.
> 
> While it is true that you should not resend patches just to add Acks,
> when re-sending a whole series that includes other changes it's still
> necessary to keep all patches together ;-)

Ah, I had misinterpreted previous advice on when it was necessary to 
repost patches.

I did wonder how maintainers would then discover the set of patches, and 
so included the "Relies on [..." text above.

I will ensure patch series are complete in future.

Thanks for your patience and review! :)

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 12+ messages in thread

end of thread, other threads:[~2022-09-05 21:01 UTC | newest]

Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-08-29  5:00 [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone Tom Fitzhenry
2022-08-29  5:00 ` Tom Fitzhenry
2022-08-29  5:00 ` Tom Fitzhenry
2022-08-29  5:00 ` [PATCH v5 1/1] arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro Tom Fitzhenry
2022-08-29  5:00   ` Tom Fitzhenry
2022-08-29  5:00   ` Tom Fitzhenry
2022-09-04 17:22 ` [PATCH v5 0/1] Add support for the Pine64 PinePhone Pro phone Heiko Stuebner
2022-09-04 17:22   ` Heiko Stuebner
2022-09-04 17:22   ` Heiko Stuebner
2022-09-05 21:00   ` Tom Fitzhenry
2022-09-05 21:00     ` Tom Fitzhenry
2022-09-05 21:00     ` Tom Fitzhenry

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.