* [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board
@ 2012-07-10 8:39 Xu Jiucheng
2012-07-10 8:39 ` [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC Xu Jiucheng
` (2 more replies)
0 siblings, 3 replies; 17+ messages in thread
From: Xu Jiucheng @ 2012-07-10 8:39 UTC (permalink / raw)
To: galak, linuxppc-dev; +Cc: Matthew McClintock, Xu Jiucheng
P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
- x1 PCIe slot or x1 PCIe to dual SATA controller
- x1 mini-PCIe slot
USB 2.0
- ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic=E2=80=99s G=
L850A
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
---
arch/powerpc/boot/dts/p1021rdb-pc.dtsi | 236 +++++++++++++++++++++++=
++++++
arch/powerpc/boot/dts/p1021rdb-pc_32b.dts | 96 ++++++++++++
arch/powerpc/boot/dts/p1021rdb-pc_36b.dts | 96 ++++++++++++
arch/powerpc/boot/dts/p1021rdb.dts | 96 ------------
arch/powerpc/boot/dts/p1021rdb.dtsi | 236 -----------------------=
------
arch/powerpc/boot/dts/p1021rdb_36b.dts | 96 ------------
6 files changed, 428 insertions(+), 428 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc.dtsi
create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_32b.dts
create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_36b.dts
delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dts
delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dtsi
delete mode 100644 arch/powerpc/boot/dts/p1021rdb_36b.dts
diff --git a/arch/powerpc/boot/dts/p1021rdb-pc.dtsi b/arch/powerpc/boot/d=
ts/p1021rdb-pc.dtsi
new file mode 100644
index 0000000..b973461
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1021rdb-pc.dtsi
@@ -0,0 +1,236 @@
+/*
+ * P1021 RDB Device Tree Source stub (no addresses or top-level ranges)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions ar=
e met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyrig=
ht
+ * notice, this list of conditions and the following disclaimer in=
the
+ * documentation and/or other materials provided with the distribu=
tion.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote pro=
ducts
+ * derived from this software without specific prior written permi=
ssion.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of th=
e
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND AN=
Y
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMP=
LIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AR=
E
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR A=
NY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DA=
MAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SE=
RVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUS=
ED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR=
TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE=
OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&lbc {
+ nor@0,0 {
+ #address-cells =3D <1>;
+ #size-cells =3D <1>;
+ compatible =3D "cfi-flash";
+ reg =3D <0x0 0x0 0x1000000>;
+ bank-width =3D <2>;
+ device-width =3D <1>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 256KB for Vitesse 7385 Switch firmware */
+ reg =3D <0x0 0x00040000>;
+ label =3D "NOR Vitesse-7385 Firmware";
+ read-only;
+ };
+
+ partition@40000 {
+ /* 256KB for DTB Image */
+ reg =3D <0x00040000 0x00040000>;
+ label =3D "NOR DTB Image";
+ };
+
+ partition@80000 {
+ /* 3.5 MB for Linux Kernel Image */
+ reg =3D <0x00080000 0x00380000>;
+ label =3D "NOR Linux Kernel Image";
+ };
+
+ partition@400000 {
+ /* 11MB for JFFS2 based Root file System */
+ reg =3D <0x00400000 0x00b00000>;
+ label =3D "NOR JFFS2 Root File System";
+ };
+
+ partition@f00000 {
+ /* This location must not be altered */
+ /* 512KB for u-boot Bootloader Image */
+ /* 512KB for u-boot Environment Variables */
+ reg =3D <0x00f00000 0x00100000>;
+ label =3D "NOR U-Boot Image";
+ };
+ };
+
+ nand@1,0 {
+ #address-cells =3D <1>;
+ #size-cells =3D <1>;
+ compatible =3D "fsl,p1021-fcm-nand",
+ "fsl,elbc-fcm-nand";
+ reg =3D <0x1 0x0 0x40000>;
+
+ partition@0 {
+ /* This location must not be altered */
+ /* 1MB for u-boot Bootloader Image */
+ reg =3D <0x0 0x00100000>;
+ label =3D "NAND U-Boot Image";
+ read-only;
+ };
+
+ partition@100000 {
+ /* 1MB for DTB Image */
+ reg =3D <0x00100000 0x00100000>;
+ label =3D "NAND DTB Image";
+ };
+
+ partition@200000 {
+ /* 4MB for Linux Kernel Image */
+ reg =3D <0x00200000 0x00400000>;
+ label =3D "NAND Linux Kernel Image";
+ };
+
+ partition@600000 {
+ /* 4MB for Compressed Root file System Image */
+ reg =3D <0x00600000 0x00400000>;
+ label =3D "NAND Compressed RFS Image";
+ };
+
+ partition@a00000 {
+ /* 7MB for JFFS2 based Root file System */
+ reg =3D <0x00a00000 0x00700000>;
+ label =3D "NAND JFFS2 Root File System";
+ };
+
+ partition@1100000 {
+ /* 15MB for User Writable Area */
+ reg =3D <0x01100000 0x00f00000>;
+ label =3D "NAND Writable User area";
+ };
+ };
+
+ L2switch@2,0 {
+ #address-cells =3D <1>;
+ #size-cells =3D <1>;
+ compatible =3D "vitesse-7385";
+ reg =3D <0x2 0x0 0x20000>;
+ };
+};
+
+&soc {
+ i2c@3000 {
+ rtc@68 {
+ compatible =3D "pericom,pt7c4338";
+ reg =3D <0x68>;
+ };
+ };
+
+ spi@7000 {
+ flash@0 {
+ #address-cells =3D <1>;
+ #size-cells =3D <1>;
+ compatible =3D "spansion,s25sl12801";
+ reg =3D <0>;
+ spi-max-frequency =3D <40000000>; /* input clock */
+
+ partition@u-boot {
+ /* 512KB for u-boot Bootloader Image */
+ reg =3D <0x0 0x00080000>;
+ label =3D "SPI Flash U-Boot Image";
+ read-only;
+ };
+
+ partition@dtb {
+ /* 512KB for DTB Image */
+ reg =3D <0x00080000 0x00080000>;
+ label =3D "SPI Flash DTB Image";
+ };
+
+ partition@kernel {
+ /* 4MB for Linux Kernel Image */
+ reg =3D <0x00100000 0x00400000>;
+ label =3D "SPI Flash Linux Kernel Image";
+ };
+
+ partition@fs {
+ /* 4MB for Compressed RFS Image */
+ reg =3D <0x00500000 0x00400000>;
+ label =3D "SPI Flash Compressed RFSImage";
+ };
+
+ partition@jffs-fs {
+ /* 7MB for JFFS2 based RFS */
+ reg =3D <0x00900000 0x00700000>;
+ label =3D "SPI Flash JFFS2 RFS";
+ };
+ };
+ };
+
+ usb@22000 {
+ phy_type =3D "ulpi";
+ };
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ interrupt-parent =3D <&mpic>;
+ interrupts =3D <3 1 0 0>;
+ reg =3D <0x0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent =3D <&mpic>;
+ interrupts =3D <2 1 0 0>;
+ reg =3D <0x1>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg =3D <0x11>;
+ device_type =3D "tbi-phy";
+ };
+ };
+
+ mdio@25000 {
+ tbi1: tbi-phy@11 {
+ reg =3D <0x11>;
+ device_type =3D "tbi-phy";
+ };
+ };
+
+ mdio@26000 {
+ tbi2: tbi-phy@11 {
+ reg =3D <0x11>;
+ device_type =3D "tbi-phy";
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ fixed-link =3D <1 1 1000 0 0>;
+ phy-connection-type =3D "rgmii-id";
+
+ };
+
+ enet1: ethernet@b1000 {
+ phy-handle =3D <&phy0>;
+ tbi-handle =3D <&tbi1>;
+ phy-connection-type =3D "sgmii";
+ };
+
+ enet2: ethernet@b2000 {
+ phy-handle =3D <&phy1>;
+ tbi-handle =3D <&tbi2>;
+ phy-connection-type =3D "rgmii-id";
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1021rdb-pc_32b.dts b/arch/powerpc/boo=
t/dts/p1021rdb-pc_32b.dts
new file mode 100644
index 0000000..22534da
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1021rdb-pc_32b.dts
@@ -0,0 +1,96 @@
+/*
+ * P1021 RDB Device Tree Source
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions ar=
e met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyrig=
ht
+ * notice, this list of conditions and the following disclaimer in=
the
+ * documentation and/or other materials provided with the distribu=
tion.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote pro=
ducts
+ * derived from this software without specific prior written permi=
ssion.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of th=
e
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMP=
LIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AR=
E
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR A=
NY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DA=
MAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SE=
RVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUS=
ED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR=
TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE=
OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1021si-pre.dtsi"
+/ {
+ model =3D "fsl,P1021RDB";
+ compatible =3D "fsl,P1021RDB-PC";
+
+ memory {
+ device_type =3D "memory";
+ };
+
+ lbc: localbus@ffe05000 {
+ reg =3D <0 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges =3D <0x0 0x0 0x0 0xef000000 0x01000000
+ 0x1 0x0 0x0 0xff800000 0x00040000
+ 0x2 0x0 0x0 0xffb00000 0x00020000>;
+ };
+
+ soc: soc@ffe00000 {
+ ranges =3D <0x0 0x0 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges =3D <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg =3D <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges =3D <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg =3D <0 0xffe0a000 0 0x1000>;
+ ranges =3D <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges =3D <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ qe: qe@ffe80000 {
+ ranges =3D <0x0 0x0 0xffe80000 0x40000>;
+ reg =3D <0 0xffe80000 0 0x480>;
+ brg-frequency =3D <0>;
+ bus-frequency =3D <0>;
+ };
+};
+
+/include/ "p1021rdb-pc.dtsi"
+/include/ "fsl/p1021si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1021rdb-pc_36b.dts b/arch/powerpc/boo=
t/dts/p1021rdb-pc_36b.dts
new file mode 100644
index 0000000..7ffe00a
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1021rdb-pc_36b.dts
@@ -0,0 +1,96 @@
+/*
+ * P1021 RDB Device Tree Source (36-bit address map)
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions ar=
e met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyrig=
ht
+ * notice, this list of conditions and the following disclaimer in=
the
+ * documentation and/or other materials provided with the distribu=
tion.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote pro=
ducts
+ * derived from this software without specific prior written permi=
ssion.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of th=
e
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMP=
LIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AR=
E
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR A=
NY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DA=
MAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SE=
RVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUS=
ED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR=
TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE=
OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "fsl/p1021si-pre.dtsi"
+/ {
+ model =3D "fsl,P1021RDB";
+ compatible =3D "fsl,P1021RDB-PC";
+
+ memory {
+ device_type =3D "memory";
+ };
+
+ lbc: localbus@fffe05000 {
+ reg =3D <0xf 0xffe05000 0 0x1000>;
+
+ /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
+ ranges =3D <0x0 0x0 0xf 0xef000000 0x01000000
+ 0x1 0x0 0xf 0xff800000 0x00040000
+ 0x2 0x0 0xf 0xffb00000 0x00020000>;
+ };
+
+ soc: soc@fffe00000 {
+ ranges =3D <0x0 0xf 0xffe00000 0x100000>;
+ };
+
+ pci0: pcie@fffe09000 {
+ ranges =3D <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
+ reg =3D <0xf 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges =3D <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@fffe0a000 {
+ reg =3D <0xf 0xffe0a000 0 0x1000>;
+ ranges =3D <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges =3D <0x2000000 0x0 0xc0000000
+ 0x2000000 0x0 0xc0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ qe: qe@fffe80000 {
+ ranges =3D <0x0 0xf 0xffe80000 0x40000>;
+ reg =3D <0xf 0xffe80000 0 0x480>;
+ brg-frequency =3D <0>;
+ bus-frequency =3D <0>;
+ };
+};
+
+/include/ "p1021rdb-pc.dtsi"
+/include/ "fsl/p1021si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1021rdb.dts b/arch/powerpc/boot/dts/p=
1021rdb.dts
deleted file mode 100644
index 90b6b4c..0000000
--- a/arch/powerpc/boot/dts/p1021rdb.dts
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * P1021 RDB Device Tree Source
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions ar=
e met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyrig=
ht
- * notice, this list of conditions and the following disclaimer in=
the
- * documentation and/or other materials provided with the distribu=
tion.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote pro=
ducts
- * derived from this software without specific prior written permi=
ssion.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of th=
e
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMP=
LIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AR=
E
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR A=
NY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DA=
MAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SE=
RVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUS=
ED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR=
TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE=
OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/include/ "fsl/p1021si-pre.dtsi"
-/ {
- model =3D "fsl,P1021RDB";
- compatible =3D "fsl,P1021RDB-PC";
-
- memory {
- device_type =3D "memory";
- };
-
- lbc: localbus@ffe05000 {
- reg =3D <0 0xffe05000 0 0x1000>;
-
- /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
- ranges =3D <0x0 0x0 0x0 0xef000000 0x01000000
- 0x1 0x0 0x0 0xff800000 0x00040000
- 0x2 0x0 0x0 0xffb00000 0x00020000>;
- };
-
- soc: soc@ffe00000 {
- ranges =3D <0x0 0x0 0xffe00000 0x100000>;
- };
-
- pci0: pcie@ffe09000 {
- ranges =3D <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
- reg =3D <0 0xffe09000 0 0x1000>;
- pcie@0 {
- ranges =3D <0x2000000 0x0 0xa0000000
- 0x2000000 0x0 0xa0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
- pci1: pcie@ffe0a000 {
- reg =3D <0 0xffe0a000 0 0x1000>;
- ranges =3D <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
- pcie@0 {
- ranges =3D <0x2000000 0x0 0x80000000
- 0x2000000 0x0 0x80000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
- qe: qe@ffe80000 {
- ranges =3D <0x0 0x0 0xffe80000 0x40000>;
- reg =3D <0 0xffe80000 0 0x480>;
- brg-frequency =3D <0>;
- bus-frequency =3D <0>;
- };
-};
-
-/include/ "p1021rdb.dtsi"
-/include/ "fsl/p1021si-post.dtsi"
diff --git a/arch/powerpc/boot/dts/p1021rdb.dtsi b/arch/powerpc/boot/dts/=
p1021rdb.dtsi
deleted file mode 100644
index b973461..0000000
--- a/arch/powerpc/boot/dts/p1021rdb.dtsi
+++ /dev/null
@@ -1,236 +0,0 @@
-/*
- * P1021 RDB Device Tree Source stub (no addresses or top-level ranges)
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions ar=
e met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyrig=
ht
- * notice, this list of conditions and the following disclaimer in=
the
- * documentation and/or other materials provided with the distribu=
tion.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote pro=
ducts
- * derived from this software without specific prior written permi=
ssion.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of th=
e
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND AN=
Y
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMP=
LIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AR=
E
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR A=
NY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DA=
MAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SE=
RVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUS=
ED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR=
TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE=
OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-&lbc {
- nor@0,0 {
- #address-cells =3D <1>;
- #size-cells =3D <1>;
- compatible =3D "cfi-flash";
- reg =3D <0x0 0x0 0x1000000>;
- bank-width =3D <2>;
- device-width =3D <1>;
-
- partition@0 {
- /* This location must not be altered */
- /* 256KB for Vitesse 7385 Switch firmware */
- reg =3D <0x0 0x00040000>;
- label =3D "NOR Vitesse-7385 Firmware";
- read-only;
- };
-
- partition@40000 {
- /* 256KB for DTB Image */
- reg =3D <0x00040000 0x00040000>;
- label =3D "NOR DTB Image";
- };
-
- partition@80000 {
- /* 3.5 MB for Linux Kernel Image */
- reg =3D <0x00080000 0x00380000>;
- label =3D "NOR Linux Kernel Image";
- };
-
- partition@400000 {
- /* 11MB for JFFS2 based Root file System */
- reg =3D <0x00400000 0x00b00000>;
- label =3D "NOR JFFS2 Root File System";
- };
-
- partition@f00000 {
- /* This location must not be altered */
- /* 512KB for u-boot Bootloader Image */
- /* 512KB for u-boot Environment Variables */
- reg =3D <0x00f00000 0x00100000>;
- label =3D "NOR U-Boot Image";
- };
- };
-
- nand@1,0 {
- #address-cells =3D <1>;
- #size-cells =3D <1>;
- compatible =3D "fsl,p1021-fcm-nand",
- "fsl,elbc-fcm-nand";
- reg =3D <0x1 0x0 0x40000>;
-
- partition@0 {
- /* This location must not be altered */
- /* 1MB for u-boot Bootloader Image */
- reg =3D <0x0 0x00100000>;
- label =3D "NAND U-Boot Image";
- read-only;
- };
-
- partition@100000 {
- /* 1MB for DTB Image */
- reg =3D <0x00100000 0x00100000>;
- label =3D "NAND DTB Image";
- };
-
- partition@200000 {
- /* 4MB for Linux Kernel Image */
- reg =3D <0x00200000 0x00400000>;
- label =3D "NAND Linux Kernel Image";
- };
-
- partition@600000 {
- /* 4MB for Compressed Root file System Image */
- reg =3D <0x00600000 0x00400000>;
- label =3D "NAND Compressed RFS Image";
- };
-
- partition@a00000 {
- /* 7MB for JFFS2 based Root file System */
- reg =3D <0x00a00000 0x00700000>;
- label =3D "NAND JFFS2 Root File System";
- };
-
- partition@1100000 {
- /* 15MB for User Writable Area */
- reg =3D <0x01100000 0x00f00000>;
- label =3D "NAND Writable User area";
- };
- };
-
- L2switch@2,0 {
- #address-cells =3D <1>;
- #size-cells =3D <1>;
- compatible =3D "vitesse-7385";
- reg =3D <0x2 0x0 0x20000>;
- };
-};
-
-&soc {
- i2c@3000 {
- rtc@68 {
- compatible =3D "pericom,pt7c4338";
- reg =3D <0x68>;
- };
- };
-
- spi@7000 {
- flash@0 {
- #address-cells =3D <1>;
- #size-cells =3D <1>;
- compatible =3D "spansion,s25sl12801";
- reg =3D <0>;
- spi-max-frequency =3D <40000000>; /* input clock */
-
- partition@u-boot {
- /* 512KB for u-boot Bootloader Image */
- reg =3D <0x0 0x00080000>;
- label =3D "SPI Flash U-Boot Image";
- read-only;
- };
-
- partition@dtb {
- /* 512KB for DTB Image */
- reg =3D <0x00080000 0x00080000>;
- label =3D "SPI Flash DTB Image";
- };
-
- partition@kernel {
- /* 4MB for Linux Kernel Image */
- reg =3D <0x00100000 0x00400000>;
- label =3D "SPI Flash Linux Kernel Image";
- };
-
- partition@fs {
- /* 4MB for Compressed RFS Image */
- reg =3D <0x00500000 0x00400000>;
- label =3D "SPI Flash Compressed RFSImage";
- };
-
- partition@jffs-fs {
- /* 7MB for JFFS2 based RFS */
- reg =3D <0x00900000 0x00700000>;
- label =3D "SPI Flash JFFS2 RFS";
- };
- };
- };
-
- usb@22000 {
- phy_type =3D "ulpi";
- };
-
- mdio@24000 {
- phy0: ethernet-phy@0 {
- interrupt-parent =3D <&mpic>;
- interrupts =3D <3 1 0 0>;
- reg =3D <0x0>;
- };
-
- phy1: ethernet-phy@1 {
- interrupt-parent =3D <&mpic>;
- interrupts =3D <2 1 0 0>;
- reg =3D <0x1>;
- };
-
- tbi0: tbi-phy@11 {
- reg =3D <0x11>;
- device_type =3D "tbi-phy";
- };
- };
-
- mdio@25000 {
- tbi1: tbi-phy@11 {
- reg =3D <0x11>;
- device_type =3D "tbi-phy";
- };
- };
-
- mdio@26000 {
- tbi2: tbi-phy@11 {
- reg =3D <0x11>;
- device_type =3D "tbi-phy";
- };
- };
-
- enet0: ethernet@b0000 {
- fixed-link =3D <1 1 1000 0 0>;
- phy-connection-type =3D "rgmii-id";
-
- };
-
- enet1: ethernet@b1000 {
- phy-handle =3D <&phy0>;
- tbi-handle =3D <&tbi1>;
- phy-connection-type =3D "sgmii";
- };
-
- enet2: ethernet@b2000 {
- phy-handle =3D <&phy1>;
- tbi-handle =3D <&tbi2>;
- phy-connection-type =3D "rgmii-id";
- };
-};
diff --git a/arch/powerpc/boot/dts/p1021rdb_36b.dts b/arch/powerpc/boot/d=
ts/p1021rdb_36b.dts
deleted file mode 100644
index ea6d8b5..0000000
--- a/arch/powerpc/boot/dts/p1021rdb_36b.dts
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * P1021 RDB Device Tree Source (36-bit address map)
- *
- * Copyright 2011 Freescale Semiconductor Inc.
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions ar=
e met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyrig=
ht
- * notice, this list of conditions and the following disclaimer in=
the
- * documentation and/or other materials provided with the distribu=
tion.
- * * Neither the name of Freescale Semiconductor nor the
- * names of its contributors may be used to endorse or promote pro=
ducts
- * derived from this software without specific prior written permi=
ssion.
- *
- *
- * ALTERNATIVELY, this software may be distributed under the terms of th=
e
- * GNU General Public License ("GPL") as published by the Free Software
- * Foundation, either version 2 of that License or (at your option) any
- * later version.
- *
- * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor "AS IS" AND ANY
- * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMP=
LIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AR=
E
- * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR A=
NY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DA=
MAGES
- * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SE=
RVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUS=
ED AND
- * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR=
TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE=
OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-/include/ "fsl/p1021si-pre.dtsi"
-/ {
- model =3D "fsl,P1021RDB";
- compatible =3D "fsl,P1021RDB-PC";
-
- memory {
- device_type =3D "memory";
- };
-
- lbc: localbus@fffe05000 {
- reg =3D <0xf 0xffe05000 0 0x1000>;
-
- /* NOR, NAND Flashes and Vitesse 5 port L2 switch */
- ranges =3D <0x0 0x0 0xf 0xef000000 0x01000000
- 0x1 0x0 0xf 0xff800000 0x00040000
- 0x2 0x0 0xf 0xffb00000 0x00020000>;
- };
-
- soc: soc@fffe00000 {
- ranges =3D <0x0 0xf 0xffe00000 0x100000>;
- };
-
- pci0: pcie@fffe09000 {
- ranges =3D <0x2000000 0x0 0xc0000000 0xc 0x20000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>;
- reg =3D <0xf 0xffe09000 0 0x1000>;
- pcie@0 {
- ranges =3D <0x2000000 0x0 0xa0000000
- 0x2000000 0x0 0xa0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
- pci1: pcie@fffe0a000 {
- reg =3D <0xf 0xffe0a000 0 0x1000>;
- ranges =3D <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000
- 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>;
- pcie@0 {
- ranges =3D <0x2000000 0x0 0xc0000000
- 0x2000000 0x0 0xc0000000
- 0x0 0x20000000
-
- 0x1000000 0x0 0x0
- 0x1000000 0x0 0x0
- 0x0 0x100000>;
- };
- };
-
- qe: qe@fffe80000 {
- ranges =3D <0x0 0xf 0xffe80000 0x40000>;
- reg =3D <0xf 0xffe80000 0 0x480>;
- brg-frequency =3D <0>;
- bus-frequency =3D <0>;
- };
-};
-
-/include/ "p1021rdb.dtsi"
-/include/ "fsl/p1021si-post.dtsi"
--=20
1.6.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-10 8:39 [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Xu Jiucheng
@ 2012-07-10 8:39 ` Xu Jiucheng
2012-07-10 12:25 ` Tabi Timur-B04825
2012-07-10 15:57 ` Scott Wood
2012-07-10 11:48 ` [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Kumar Gala
2012-07-11 12:43 ` Kumar Gala
2 siblings, 2 replies; 17+ messages in thread
From: Xu Jiucheng @ 2012-07-10 8:39 UTC (permalink / raw)
To: galak, linuxppc-dev; +Cc: Matthew McClintock, Xu Jiucheng
Create the dts files for each core and splits the devices between
the two cores for P1021RDB-PC.
Core0 has l2, serial0, i2c, spi, gpio, tdm,dma, usb, eth0, eth1,
sdhc, crypto, global-util, message, pci0, pci1, msi, crypto.
Core1 has l2, serial1, eth2.
Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
---
arch/powerpc/boot/dts/p1021rdb-pc_camp_core0.dts | 91 +++++++++++
arch/powerpc/boot/dts/p1021rdb-pc_camp_core1.dts | 179 ++++++++++++++++++++++
2 files changed, 270 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_camp_core0.dts
create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_camp_core1.dts
diff --git a/arch/powerpc/boot/dts/p1021rdb-pc_camp_core0.dts b/arch/powerpc/boot/dts/p1021rdb-pc_camp_core0.dts
new file mode 100644
index 0000000..199e94e
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1021rdb-pc_camp_core0.dts
@@ -0,0 +1,91 @@
+/*
+ * P1021 RDB Core0 Device Tree Source in CAMP mode.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts file allows core0 to have memory, l2, serail0, i2c, spi, gpio,
+ * tdm, dma, usb, eth0, eth1, sdhc, crypto, global-util, message, pci0, pci1,
+ * msi.
+ *
+ * Please note to add "-b 0" for core0's dts compiling.
+ */
+
+/include/ "p1021rdb-pc_32b.dts"
+
+/ {
+ model = "fsl,P1021RDB";
+ compatible = "fsl,P1021RDB-PC";
+
+ aliases {
+ ethernet1 = &enet0;
+ ethernet2 = &enet1;
+ serial0 = &serial0;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ };
+
+ cpus {
+ PowerPC,P1021@1 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ soc@ffe00000 {
+ serial1: serial@4600 {
+ status = "disabled";
+ };
+
+ mdio@24000 {
+ phy1: ethernet-phy@1 {
+ status = "disabled";
+ };
+ };
+
+ enet2: ethernet@b2000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 42 /* serial1 */
+ 31 32 33 /* enet2-queue-group0 */
+ 25 26 27 /* enet2-queue-group1 */
+ >;
+ pic-no-reset;
+ };
+ };
+};
diff --git a/arch/powerpc/boot/dts/p1021rdb-pc_camp_core1.dts b/arch/powerpc/boot/dts/p1021rdb-pc_camp_core1.dts
new file mode 100644
index 0000000..dfc9105
--- /dev/null
+++ b/arch/powerpc/boot/dts/p1021rdb-pc_camp_core1.dts
@@ -0,0 +1,179 @@
+/*
+ * P1021 RDB Core1 Device Tree Source in CAMP mode.
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * In CAMP mode, each core needs to have its own dts. Only mpic and L2 cache
+ * can be shared, all the other devices must be assigned to one core only.
+ * This dts allows core1 to have l2, eth2, serial1, crypto.
+ *
+ * Please note to add "-b 1" for core1's dts compiling.
+ */
+
+/include/ "p1021rdb-pc_32b.dts"
+
+/ {
+ model = "fsl,P1021RDB";
+ compatible = "fsl,P1021RDB-PC";
+
+ aliases {
+ ethernet0 = &enet2;
+ serial0 = &serial1;
+ };
+
+ cpus {
+ PowerPC,P1021@0 {
+ status = "disabled";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ localbus@ffe05000 {
+ status = "disabled";
+ };
+
+ soc@ffe00000 {
+ ecm-law@0 {
+ status = "disabled";
+ };
+
+ ecm@1000 {
+ status = "disabled";
+ };
+
+ memory-controller@2000 {
+ status = "disabled";
+ };
+
+ i2c@3000 {
+ status = "disabled";
+ };
+
+ i2c@3100 {
+ status = "disabled";
+ };
+
+ serial0: serial@4500 {
+ status = "disabled";
+ };
+
+ spi@7000 {
+ status = "disabled";
+ };
+
+ gpio: gpio-controller@f000 {
+ status = "disabled";
+ };
+
+ dma@21300 {
+ status = "disabled";
+ };
+
+ mdio@24000 {
+ phy0: ethernet-phy@0 {
+ status = "disabled";
+ };
+
+ tbi0: tbi-phy@11 {
+ status = "disabled";
+ };
+ };
+
+ mdio@25000 {
+ status = "disabled";
+ };
+
+ mdio@26000 {
+ status = "disabled";
+ };
+
+ enet0: ethernet@b0000 {
+ status = "disabled";
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ usb@22000 {
+ status = "disabled";
+ };
+
+ sdhci@2e000 {
+ status = "disabled";
+ };
+
+ crypto@30000 {
+ status = "disabled";
+ };
+
+ mpic: pic@40000 {
+ protected-sources = <
+ 16 /* ecm, mem, L2, pci0, pci1 */
+ 43 42 59 /* i2c, serial0, spi */
+ 47 63 62 /* gpio, tdm */
+ 20 21 22 23 /* dma */
+ 03 02 /* mdio */
+ 29 30 34 /* enet0-queue-group0 */
+ 17 18 24 /* enet0-queue-group1 */
+ 35 36 40 /* enet1-queue-group0 */
+ 51 52 67 /* enet1-queue-group1 */
+ 28 72 45 58 /* usb, sdhci, crypto */
+ 0xb0 0xb1 0xb2 /* message */
+ 0xb3 0xb4 0xb5
+ 0xb6 0xb7
+ 0xe0 0xe1 0xe2 /* msi */
+ 0xe3 0xe4 0xe5
+ 0xe6 0xe7 /* sdhci, crypto , pci */
+ >;
+ pic-no-reset;
+ };
+
+ msi@41600 {
+ status = "disabled";
+ };
+
+ global-utilities@e0000 { //global utilities block
+ status = "disabled";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ status = "disabled";
+ };
+
+ pci1: pcie@ffe0a000 {
+ status = "disabled";
+ };
+};
--
1.6.4
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board
2012-07-10 8:39 [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Xu Jiucheng
2012-07-10 8:39 ` [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC Xu Jiucheng
@ 2012-07-10 11:48 ` Kumar Gala
2012-07-11 9:58 ` Jiucheng Xu
2012-07-11 12:43 ` Kumar Gala
2 siblings, 1 reply; 17+ messages in thread
From: Kumar Gala @ 2012-07-10 11:48 UTC (permalink / raw)
To: Xu Jiucheng; +Cc: Matthew McClintock, linuxppc-dev
On Jul 10, 2012, at 3:39 AM, Xu Jiucheng wrote:
> P1021RDB-PC Overview
> -----------------
> 1Gbyte DDR3 (on board DDR)
> 16Mbyte NOR flash
> 32Mbyte eSLC NAND Flash
> 256 Kbit M24256 I2C EEPROM
> 128 Mbit SPI Flash memory
> Real-time clock on I2C bus
> SD/MMC connector to interface with the SD memory card
> PCIex
> - x1 PCIe slot or x1 PCIe to dual SATA controller
> - x1 mini-PCIe slot
> USB 2.0
> - ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic=92s =
GL850A
> - Two USB2.0 Type A receptacles
> - One USB2.0 signal to Mini PCIe slot
> eTSEC1: Connected to RGMII PHY VSC7385
> eTSEC2: Connected to SGMII PHY VSC8221
> eTSEC3: Connected to SGMII PHY AR8021
> DUART interface: supports two UARTs up to 115200 bps for console =
display
>=20
> Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
> Signed-off-by: Matthew McClintock <msm@freescale.com>
> ---
> arch/powerpc/boot/dts/p1021rdb-pc.dtsi | 236 =
+++++++++++++++++++++++++++++
> arch/powerpc/boot/dts/p1021rdb-pc_32b.dts | 96 ++++++++++++
> arch/powerpc/boot/dts/p1021rdb-pc_36b.dts | 96 ++++++++++++
> arch/powerpc/boot/dts/p1021rdb.dts | 96 ------------
> arch/powerpc/boot/dts/p1021rdb.dtsi | 236 =
-----------------------------
> arch/powerpc/boot/dts/p1021rdb_36b.dts | 96 ------------
> 6 files changed, 428 insertions(+), 428 deletions(-)
> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc.dtsi
> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_32b.dts
> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_36b.dts
> delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dts
> delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dtsi
> delete mode 100644 arch/powerpc/boot/dts/p1021rdb_36b.dts
Do we really need a 32 & 36 bit device tree for this board? Isnt the =
memory fixed so why not just have 32b?
Also, why are you removing the dts for the older P1021RDB??
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-10 8:39 ` [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC Xu Jiucheng
@ 2012-07-10 12:25 ` Tabi Timur-B04825
2012-07-11 14:47 ` Kumar Gala
2012-07-10 15:57 ` Scott Wood
1 sibling, 1 reply; 17+ messages in thread
From: Tabi Timur-B04825 @ 2012-07-10 12:25 UTC (permalink / raw)
To: Xu Jiucheng-B37781; +Cc: McClintock Matthew-B29882, linuxppc-dev
On Tue, Jul 10, 2012 at 3:39 AM, Xu Jiucheng <Jiucheng.Xu@freescale.com> wr=
ote:
> Create the dts files for each core and splits the devices between
> the two cores for P1021RDB-PC.
>
> Core0 has l2, serial0, i2c, spi, gpio, tdm,dma, usb, eth0, eth1,
> sdhc, crypto, global-util, message, pci0, pci1, msi, crypto.
> Core1 has l2, serial1, eth2.
>
> Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
> Signed-off-by: Matthew McClintock <msm@freescale.com>
> ---
Do we really want AMP device trees upstream? They're very
application-specific, and AMP support has always been a hack. If
anything, I think we should be deleting AMP device trees from
upstream, not adding more.
--=20
Timur Tabi
Linux kernel developer at Freescale=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-10 8:39 ` [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC Xu Jiucheng
2012-07-10 12:25 ` Tabi Timur-B04825
@ 2012-07-10 15:57 ` Scott Wood
1 sibling, 0 replies; 17+ messages in thread
From: Scott Wood @ 2012-07-10 15:57 UTC (permalink / raw)
To: Xu Jiucheng; +Cc: Matthew McClintock, linuxppc-dev
On 07/10/2012 03:39 AM, Xu Jiucheng wrote:
> + crypto@30000 {
> + status = "disabled";
> + };
Whitespace.
> +
> + mpic: pic@40000 {
> + protected-sources = <
> + 16 /* ecm, mem, L2, pci0, pci1 */
> + 43 42 59 /* i2c, serial0, spi */
> + 47 63 62 /* gpio, tdm */
> + 20 21 22 23 /* dma */
> + 03 02 /* mdio */
> + 29 30 34 /* enet0-queue-group0 */
> + 17 18 24 /* enet0-queue-group1 */
> + 35 36 40 /* enet1-queue-group0 */
> + 51 52 67 /* enet1-queue-group1 */
> + 28 72 45 58 /* usb, sdhci, crypto */
> + 0xb0 0xb1 0xb2 /* message */
> + 0xb3 0xb4 0xb5
> + 0xb6 0xb7
> + 0xe0 0xe1 0xe2 /* msi */
> + 0xe3 0xe4 0xe5
> + 0xe6 0xe7 /* sdhci, crypto , pci */
> + >;
> + pic-no-reset;
> + };
Besides what Timur said, do we really need protected-sources now that we
have pic-no-reset?
-Scott
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board
2012-07-10 11:48 ` [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Kumar Gala
@ 2012-07-11 9:58 ` Jiucheng Xu
2012-07-11 12:31 ` Kumar Gala
0 siblings, 1 reply; 17+ messages in thread
From: Jiucheng Xu @ 2012-07-11 9:58 UTC (permalink / raw)
To: Kumar Gala; +Cc: linuxppc-dev
On Tue, 2012-07-10 at 06:48 -0500, Kumar Gala wrote:
> On Jul 10, 2012, at 3:39 AM, Xu Jiucheng wrote:
> > ---
> > arch/powerpc/boot/dts/p1021rdb-pc.dtsi | 236 +++++++++++++++++++++++++++++
> > arch/powerpc/boot/dts/p1021rdb-pc_32b.dts | 96 ++++++++++++
> > arch/powerpc/boot/dts/p1021rdb-pc_36b.dts | 96 ++++++++++++
> > arch/powerpc/boot/dts/p1021rdb.dts | 96 ------------
> > arch/powerpc/boot/dts/p1021rdb.dtsi | 236 -----------------------------
> > arch/powerpc/boot/dts/p1021rdb_36b.dts | 96 ------------
> > 6 files changed, 428 insertions(+), 428 deletions(-)
> > create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc.dtsi
> > create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_32b.dts
> > create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_36b.dts
> > delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dts
> > delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dtsi
> > delete mode 100644 arch/powerpc/boot/dts/p1021rdb_36b.dts
>
> Do we really need a 32 & 36 bit device tree for this board? Isnt the memory fixed so why not just have 32b?
>
I have no idea, 36 bit is already there in the history release of SDK,
If it is not necessary for upstream, I can resend a new patch without 36
bit.
> Also, why are you removing the dts for the older P1021RDB??
>
> - k
This dts for the older P1021RDB was committed by me. I just rename these
files in order to keep uniformity with other platforms, e.g
"P1020rdb-pc.dtsi p1020mbg-pc.dtsi". If you think it doesn't matter,
please ignore this patch.
If AMP is a specific application as Timur says, please ignore the AMP
patch.
Thanks,
Jiucheng
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board
2012-07-11 9:58 ` Jiucheng Xu
@ 2012-07-11 12:31 ` Kumar Gala
0 siblings, 0 replies; 17+ messages in thread
From: Kumar Gala @ 2012-07-11 12:31 UTC (permalink / raw)
To: Jiucheng Xu; +Cc: linuxppc-dev
On Jul 11, 2012, at 4:58 AM, Jiucheng Xu wrote:
>=20
>=20
> On Tue, 2012-07-10 at 06:48 -0500, Kumar Gala wrote:
>> On Jul 10, 2012, at 3:39 AM, Xu Jiucheng wrote:
>>> ---
>>> arch/powerpc/boot/dts/p1021rdb-pc.dtsi | 236 =
+++++++++++++++++++++++++++++
>>> arch/powerpc/boot/dts/p1021rdb-pc_32b.dts | 96 ++++++++++++
>>> arch/powerpc/boot/dts/p1021rdb-pc_36b.dts | 96 ++++++++++++
>>> arch/powerpc/boot/dts/p1021rdb.dts | 96 ------------
>>> arch/powerpc/boot/dts/p1021rdb.dtsi | 236 =
-----------------------------
>>> arch/powerpc/boot/dts/p1021rdb_36b.dts | 96 ------------
>>> 6 files changed, 428 insertions(+), 428 deletions(-)
>>> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc.dtsi
>>> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_32b.dts
>>> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_36b.dts
>>> delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dts
>>> delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dtsi
>>> delete mode 100644 arch/powerpc/boot/dts/p1021rdb_36b.dts
>>=20
>> Do we really need a 32 & 36 bit device tree for this board? Isnt the =
memory fixed so why not just have 32b?
>>=20
> I have no idea, 36 bit is already there in the history release of SDK,
> If it is not necessary for upstream, I can resend a new patch without =
36
> bit.
>> Also, why are you removing the dts for the older P1021RDB??
>>=20
>> - k
> This dts for the older P1021RDB was committed by me. I just rename =
these
> files in order to keep uniformity with other platforms, e.g
> "P1020rdb-pc.dtsi p1020mbg-pc.dtsi". If you think it doesn't matter,
> please ignore this patch.
Sorry, I was thinking there was a different board for P1021RDB (older =
than P1021RDB-PC), like we have for P1020RDB.
> If AMP is a specific application as Timur says, please ignore the AMP
> patch.
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board
2012-07-10 8:39 [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Xu Jiucheng
2012-07-10 8:39 ` [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC Xu Jiucheng
2012-07-10 11:48 ` [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Kumar Gala
@ 2012-07-11 12:43 ` Kumar Gala
2 siblings, 0 replies; 17+ messages in thread
From: Kumar Gala @ 2012-07-11 12:43 UTC (permalink / raw)
To: Xu Jiucheng; +Cc: Matthew McClintock, linuxppc-dev
On Jul 10, 2012, at 3:39 AM, Xu Jiucheng wrote:
> P1021RDB-PC Overview
> -----------------
> 1Gbyte DDR3 (on board DDR)
> 16Mbyte NOR flash
> 32Mbyte eSLC NAND Flash
> 256 Kbit M24256 I2C EEPROM
> 128 Mbit SPI Flash memory
> Real-time clock on I2C bus
> SD/MMC connector to interface with the SD memory card
> PCIex
> - x1 PCIe slot or x1 PCIe to dual SATA controller
> - x1 mini-PCIe slot
> USB 2.0
> - ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic=92s =
GL850A
> - Two USB2.0 Type A receptacles
> - One USB2.0 signal to Mini PCIe slot
> eTSEC1: Connected to RGMII PHY VSC7385
> eTSEC2: Connected to SGMII PHY VSC8221
> eTSEC3: Connected to SGMII PHY AR8021
> DUART interface: supports two UARTs up to 115200 bps for console =
display
>=20
> Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
> Signed-off-by: Matthew McClintock <msm@freescale.com>
> ---
> arch/powerpc/boot/dts/p1021rdb-pc.dtsi | 236 =
+++++++++++++++++++++++++++++
> arch/powerpc/boot/dts/p1021rdb-pc_32b.dts | 96 ++++++++++++
> arch/powerpc/boot/dts/p1021rdb-pc_36b.dts | 96 ++++++++++++
> arch/powerpc/boot/dts/p1021rdb.dts | 96 ------------
> arch/powerpc/boot/dts/p1021rdb.dtsi | 236 =
-----------------------------
> arch/powerpc/boot/dts/p1021rdb_36b.dts | 96 ------------
> 6 files changed, 428 insertions(+), 428 deletions(-)
> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc.dtsi
> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_32b.dts
> create mode 100644 arch/powerpc/boot/dts/p1021rdb-pc_36b.dts
> delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dts
> delete mode 100644 arch/powerpc/boot/dts/p1021rdb.dtsi
> delete mode 100644 arch/powerpc/boot/dts/p1021rdb_36b.dts
applied to next. Rewrote commit message to just say we are renaming the =
device trees.
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-10 12:25 ` Tabi Timur-B04825
@ 2012-07-11 14:47 ` Kumar Gala
2012-07-11 14:49 ` Timur Tabi
0 siblings, 1 reply; 17+ messages in thread
From: Kumar Gala @ 2012-07-11 14:47 UTC (permalink / raw)
To: Tabi Timur-B04825
Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
On Jul 10, 2012, at 7:25 AM, Tabi Timur-B04825 wrote:
> On Tue, Jul 10, 2012 at 3:39 AM, Xu Jiucheng =
<Jiucheng.Xu@freescale.com> wrote:
>> Create the dts files for each core and splits the devices between
>> the two cores for P1021RDB-PC.
>>=20
>> Core0 has l2, serial0, i2c, spi, gpio, tdm,dma, usb, eth0, eth1,
>> sdhc, crypto, global-util, message, pci0, pci1, msi, crypto.
>> Core1 has l2, serial1, eth2.
>>=20
>> Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
>> Signed-off-by: Matthew McClintock <msm@freescale.com>
>> ---
>=20
> Do we really want AMP device trees upstream? They're very
> application-specific, and AMP support has always been a hack. If
> anything, I think we should be deleting AMP device trees from
> upstream, not adding more.
Since we already have P1021RDB-PC w/AMP support in upstream I agree we =
don't need another example on P1021RDB-PC.
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-11 14:47 ` Kumar Gala
@ 2012-07-11 14:49 ` Timur Tabi
2012-07-11 14:52 ` AW: " Schneider, Kolja
2012-07-11 14:53 ` Kumar Gala
0 siblings, 2 replies; 17+ messages in thread
From: Timur Tabi @ 2012-07-11 14:49 UTC (permalink / raw)
To: Kumar Gala; +Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
Kumar Gala wrote:
> Since we already have P1021RDB-PC w/AMP support in upstream I agree we don't need another example on P1021RDB-PC.
Would you accept a patch that removes all AMP device trees from upstream?
I just don't think that these very customer-specific dts files belong
upstream.
--
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply [flat|nested] 17+ messages in thread
* AW: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-11 14:49 ` Timur Tabi
@ 2012-07-11 14:52 ` Schneider, Kolja
2012-07-11 14:56 ` Timur Tabi
2012-07-11 14:53 ` Kumar Gala
1 sibling, 1 reply; 17+ messages in thread
From: Schneider, Kolja @ 2012-07-11 14:52 UTC (permalink / raw)
To: Timur Tabi, Kumar Gala
Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
> Kumar Gala wrote:
> > Since we already have P1021RDB-PC w/AMP support in upstream I agree
> we don't need another example on P1021RDB-PC.
>=20
> Would you accept a patch that removes all AMP device trees from upstream?
> I just don't think that these very customer-specific dts files belong
> upstream
[>]=20
Is there any alternate source for AMP device trees? Just in case someone
needs some sort of documentation?
:-) Kolja
.
>=20
> --
> Timur Tabi
> Linux kernel developer at Freescale
>=20
> _______________________________________________
> Linuxppc-dev mailing list
> Linuxppc-dev@lists.ozlabs.org
> https://lists.ozlabs.org/listinfo/linuxppc-dev
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-11 14:49 ` Timur Tabi
2012-07-11 14:52 ` AW: " Schneider, Kolja
@ 2012-07-11 14:53 ` Kumar Gala
2012-07-11 14:56 ` Timur Tabi
1 sibling, 1 reply; 17+ messages in thread
From: Kumar Gala @ 2012-07-11 14:53 UTC (permalink / raw)
To: Timur Tabi; +Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
On Jul 11, 2012, at 9:49 AM, Timur Tabi wrote:
> Kumar Gala wrote:
>> Since we already have P1021RDB-PC w/AMP support in upstream I agree =
we don't need another example on P1021RDB-PC.
>=20
> Would you accept a patch that removes all AMP device trees from =
upstream?
> I just don't think that these very customer-specific dts files belong
> upstream.
No, I think we should have at least one or two examples of AMP dts in =
upstream.
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: AW: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-11 14:52 ` AW: " Schneider, Kolja
@ 2012-07-11 14:56 ` Timur Tabi
0 siblings, 0 replies; 17+ messages in thread
From: Timur Tabi @ 2012-07-11 14:56 UTC (permalink / raw)
To: Schneider, Kolja
Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
Schneider, Kolja wrote:
>
> Is there any alternate source for AMP device trees? Just in case someone
> needs some sort of documentation?
The SDK. We can put a hundred AMP device trees on there if we want, and
no one will complain.
--
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-11 14:53 ` Kumar Gala
@ 2012-07-11 14:56 ` Timur Tabi
2012-07-12 3:16 ` Kumar Gala
0 siblings, 1 reply; 17+ messages in thread
From: Timur Tabi @ 2012-07-11 14:56 UTC (permalink / raw)
To: Kumar Gala; +Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
Kumar Gala wrote:
> No, I think we should have at least one or two examples of AMP dts in upstream.
We have more than that:
./p2020rdb_camp_core1.dts
./p1020rdb-pc_camp_core1.dts
./mpc8572ds_camp_core1.dts
./p2020rdb_camp_core0.dts
./p1020rdb-pc_camp_core0.dts
./mpc8572ds_camp_core0.dts
./p1020rdb_camp_core1.dts
./p1020rdb_camp_core0.dts
--
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-11 14:56 ` Timur Tabi
@ 2012-07-12 3:16 ` Kumar Gala
2012-07-12 3:53 ` Tabi Timur-B04825
0 siblings, 1 reply; 17+ messages in thread
From: Kumar Gala @ 2012-07-12 3:16 UTC (permalink / raw)
To: Timur Tabi; +Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
On Jul 11, 2012, at 9:56 AM, Timur Tabi wrote:
> Kumar Gala wrote:
>> No, I think we should have at least one or two examples of AMP dts in =
upstream.
>=20
> We have more than that:
>=20
> ./p2020rdb_camp_core1.dts
> ./p1020rdb-pc_camp_core1.dts
> ./mpc8572ds_camp_core1.dts
> ./p2020rdb_camp_core0.dts
> ./p1020rdb-pc_camp_core0.dts
> ./mpc8572ds_camp_core0.dts
> ./p1020rdb_camp_core1.dts
> ./p1020rdb_camp_core0.dts
>=20
I'd be ok if we want to drop the p1020rdb as that board has been =
replaced w/the p1020rdb-pc.
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-12 3:16 ` Kumar Gala
@ 2012-07-12 3:53 ` Tabi Timur-B04825
2012-07-12 4:05 ` Kumar Gala
0 siblings, 1 reply; 17+ messages in thread
From: Tabi Timur-B04825 @ 2012-07-12 3:53 UTC (permalink / raw)
To: Kumar Gala; +Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
Kumar Gala wrote:
>> >
>> >./p2020rdb_camp_core1.dts
>> >./p1020rdb-pc_camp_core1.dts
>> >./mpc8572ds_camp_core1.dts
>> >./p2020rdb_camp_core0.dts
>> >./p1020rdb-pc_camp_core0.dts
>> >./mpc8572ds_camp_core0.dts
>> >./p1020rdb_camp_core1.dts
>> >./p1020rdb_camp_core0.dts
>> >
> I'd be ok if we want to drop the p1020rdb as that board has been replaced=
w/the p1020rdb-pc.
How about dropping the P2020RDB as well? Then we have only two examples:=20
MPC8572DS and P1020RDB-PC.
--=20
Timur Tabi
Linux kernel developer at Freescale
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC
2012-07-12 3:53 ` Tabi Timur-B04825
@ 2012-07-12 4:05 ` Kumar Gala
0 siblings, 0 replies; 17+ messages in thread
From: Kumar Gala @ 2012-07-12 4:05 UTC (permalink / raw)
To: Tabi Timur-B04825
Cc: McClintock Matthew-B29882, Xu Jiucheng-B37781, linuxppc-dev
On Jul 11, 2012, at 10:53 PM, Tabi Timur-B04825 wrote:
> Kumar Gala wrote:
>>>>=20
>>>> ./p2020rdb_camp_core1.dts
>>>> ./p1020rdb-pc_camp_core1.dts
>>>> ./mpc8572ds_camp_core1.dts
>>>> ./p2020rdb_camp_core0.dts
>>>> ./p1020rdb-pc_camp_core0.dts
>>>> ./mpc8572ds_camp_core0.dts
>>>> ./p1020rdb_camp_core1.dts
>>>> ./p1020rdb_camp_core0.dts
>>>>=20
>> I'd be ok if we want to drop the p1020rdb as that board has been =
replaced w/the p1020rdb-pc.
>=20
> How about dropping the P2020RDB as well? Then we have only two =
examples:=20
> MPC8572DS and P1020RDB-PC.
I'm ok with dropping P2020RDB as well.
- k=
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2012-07-12 4:05 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2012-07-10 8:39 [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Xu Jiucheng
2012-07-10 8:39 ` [PATCH 2/2] powerpc/85xx: Create dts of each core in CAMP mode for P1021RDB-PC Xu Jiucheng
2012-07-10 12:25 ` Tabi Timur-B04825
2012-07-11 14:47 ` Kumar Gala
2012-07-11 14:49 ` Timur Tabi
2012-07-11 14:52 ` AW: " Schneider, Kolja
2012-07-11 14:56 ` Timur Tabi
2012-07-11 14:53 ` Kumar Gala
2012-07-11 14:56 ` Timur Tabi
2012-07-12 3:16 ` Kumar Gala
2012-07-12 3:53 ` Tabi Timur-B04825
2012-07-12 4:05 ` Kumar Gala
2012-07-10 15:57 ` Scott Wood
2012-07-10 11:48 ` [PATCH] powerpc/85xx: Add dts files for P1021RDB-PC board Kumar Gala
2012-07-11 9:58 ` Jiucheng Xu
2012-07-11 12:31 ` Kumar Gala
2012-07-11 12:43 ` Kumar Gala
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.