From mboxrd@z Thu Jan 1 00:00:00 1970 From: Alexander Bartha Date: Mon, 16 Feb 2009 21:51:15 +0100 Subject: [ath9k-devel] ath9k WMP300nv2 (AR5416) In-Reply-To: <43e72e890902141718v544f5caejb71f53bdadbf8a8f@mail.gmail.com> References: <20090203173228.GB9713@tesla> <20090203184632.137560@gmx.net> <20090203190955.GB15591@tesla> <20090203201941.242400@gmx.net> <20090203212317.GA25036@tesla> <20090204194544.158460@gmx.net> <20090204214334.GF5581@tesla> <20090206202205.218710@gmx.net> <20090206211804.GG5031@tesla> <20090214230618.203560@gmx.net> <43e72e890902141718v544f5caejb71f53bdadbf8a8f@mail.gmail.com> Message-ID: <20090216205115.21860@gmx.net> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: ath9k-devel@lists.ath9k.org Hello Luis, i have rebuild compat-wireless with CONFIG_ATH9K_DEBUG=y in config.mk then -- make unload -- modprobe ath9k debug=0x00000080 -- iw list-- (Output) -2009-02-16 # iw list Wiphy phy0 Band 1: HT capabilities: 0x104e * 20/40 MHz operation * SM PS disabled * 40 MHz short GI * max A-MSDU len 3839 * DSSS/CCK 40 MHz HT A-MPDU factor: 0x0003 (65535 bytes) HT A-MPDU density: 0x0006 (8 usec) HT MCS set: ff ff 00 00 00 00 00 00 00 00 00 00 01 00 00 00 Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) * 2472 MHz [13] (20.0 dBm) * 2484 MHz [14] (disabled) Bitrates: * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Supported interface modes: * IBSS * Station * AP * AP(VLAN) * Monitor Looks good but after boot i never have channel 12 or 13. The led on my LinksysWMP300Nv2 Card turned off after starting wpa_supplicant. At this point i cant get any connection to my AP. The only way is to reload cfg80211 mac80211 ath9k. After the reload he connects my outomatically to my AP without starting the /etc/init.d/net.wlan0 start script. I have also patched the /usr/src/compat-wireless-2009-02-16/net/wireless/reg.c file with the same-hint.patch what to do next??? The patch has not changed the need of reloading cfg80211 mac80211 and ath9k after boot if i want use my LinksysWMP300Nv2. Udev: /lib/udev/rules.d/85-regulatory.rules the location seems to be ok. but at boot of my system he never loads the second part of the frequences when cfg80211 loads. Well evening from Vienna Alexander Bartha -- Psssst! Schon vom neuen GMX MultiMessenger geh?rt? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger01