All of lore.kernel.org
 help / color / mirror / Atom feed
* HDD not suspending properly / dead on resume
@ 2010-07-09 15:50 ` Stephan Diestelhorst
  0 siblings, 0 replies; 78+ messages in thread
From: Stephan Diestelhorst @ 2010-07-09 15:50 UTC (permalink / raw)
  To: Tejun Heo, Rafael J. Wysocki
  Cc: linux-kernel, linux-ide, linux-pm, stephan.diestelhorst

[-- Attachment #1: Type: text/plain, Size: 3948 bytes --]

Hi,
  I have n issue with suepnd to RAM and I/O load on a disk. Symptoms
are that the disk does not respond to requests when woken up, producing
only I/O errors on all tested kernels (newest 2.6.35-rc4 (Ubuntu
mainline PPA build)):

[ 1719.580169] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.580174] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.580178] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 51 e7 88 00 00 b0 00
[ 1719.580186] end_request: I/O error, dev sda, sector 257025928
[ 1719.580798] Aborting journal on device dm-1-8.
[ 1719.580912] EXT4-fs error (device dm-1) in ext4_reserve_inode_write: Journal has aborted
[ 1719.580959] EXT4-fs (dm-1): Remounting filesystem read-only
[ 1719.581004] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.581007] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.581010] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 51 a1 88 00 00 08 00
[ 1719.581016] end_request: I/O error, dev sda, sector 257008008
[ 1719.581026] Buffer I/O error on device dm-1, logical block 2129920
[ 1719.581027] lost page write due to I/O error on dm-1
[ 1719.581149] 
[ 1719.581214] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.581217] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.581220] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0e 4d a1 88 00 00 08 00
[ 1719.581227] end_request: I/O error, dev sda, sector 239968648
[ 1719.581254] JBD2: I/O error detected when updating journal superblock for dm-1-8.
[ 1719.581268] journal commit I/O error

This can be triggered most reliably with multiple "direct" writes to
disk, I create the load with the attached script. If the issue is
triggered, suspend (through pm-suspend) takes very long.

IMHO the interesting log output during suspend is:
[ 1668.150125] Suspending console(s) (use no_console_suspend to debug)
[ 1668.150460] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 1668.174958] sd 0:0:0:0: [sda] Stopping disk
[ 1668.198045] ACPI handle has no context!
[ 1668.199302] ohci_hcd 0000:00:14.5: PCI INT C disabled
[ 1668.199468] ohci_hcd 0000:00:13.1: PCI INT A disabled
[ 1668.199477] ohci_hcd 0000:00:13.0: PCI INT A disabled
[ 1668.199520] ehci_hcd 0000:00:12.2: PCI INT B disabled
[ 1668.199525] ohci_hcd 0000:00:12.1: PCI INT A disabled
[ 1668.199562] ohci_hcd 0000:00:12.0: PCI INT A disabled
[ 1668.210138] ehci_hcd 0000:00:13.2: PCI INT B disabled
[ 1668.300295] HDA Intel 0000:00:14.2: PCI INT A disabled
[ 1668.300301] HDA Intel 0000:01:00.1: PCI INT B disabled
[ 1668.300349] ACPI handle has no context!
[ 1669.700139] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1674.700125] ata1.00: qc timeout (cmd 0xec)
[ 1674.700136] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 1674.700139] ata1.00: revalidation failed (errno=-5)
[ 1675.230136] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1685.230125] ata1.00: qc timeout (cmd 0xec)
[ 1685.230137] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 1685.230140] ata1.00: revalidation failed (errno=-5)
[ 1685.230144] ata1: limiting SATA link speed to 1.5 Gbps
[ 1685.760137] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1715.760126] ata1.00: qc timeout (cmd 0xec)
[ 1715.760137] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 1715.760139] ata1.00: revalidation failed (errno=-5)
[ 1715.760142] ata1.00: disabled
[ 1715.810216] ahci 0000:00:11.0: PCI INT A disabled
[ 1715.830154] PM: suspend of devices complete after 47679.847 msecs

I've also attached the full dmesg, lspci -vv and smartctl -a
information.

Do you guys have any ideas here?

Many thanks,
  Stephan
-- 
Stephan Diestelhorst, AMD Operating System Research Center
stephan.diestelhorst@amd.com, Tel. +49 (0)351 448 356 719

Advanced Micro Devices GmbH Einsteinring 24 85609 Dornach
General Managers: Alberto Bozzo, Andrew Bowd
Registration: Dornach, Landkr. Muenchen; Registerger. Muenchen, HRB Nr. 43632

[-- Attachment #2: dmesg --]
[-- Type: text/plain, Size: 62689 bytes --]

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.35-020635rc4-generic (root@zinc) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #020635rc4 SMP Mon Jul 5 09:08:26 UTC 2010
[    0.000000] Command line: BOOT_IMAGE=/vmlinuz-2.6.35-020635rc4-generic root=/dev/mapper/pool01-root ro console=ttyUSB0,9600n8 console=tty0
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[    0.000000]  BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000c7ea0000 (usable)
[    0.000000]  BIOS-e820: 00000000c7ea0000 - 00000000c7ebc000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000c7ebc000 - 00000000c7ebe000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000c7ebe000 - 00000000c8000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000138000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI present.
[    0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 update range: 0000000000000000 - 0000000000001000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] No AGP bridge found
[    0.000000] last_pfn = 0x138000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CEFFF write-protect
[    0.000000]   CF000-DEFFF uncachable
[    0.000000]   DF000-DFFFF write-back
[    0.000000]   E0000-E3FFF uncachable
[    0.000000]   E4000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000000 mask FFFF80000000 write-back
[    0.000000]   1 base 000080000000 mask FFFFC0000000 write-back
[    0.000000]   2 base 0000C0000000 mask FFFFF8000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000138000000 aka 4992M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 00000000c8000000 - 0000000100000000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0xc7ea0 max_arch_pfn = 0x400000000
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009dc00 (usable)
[    0.000000]  modified: 000000000009dc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000d0000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 00000000c7ea0000 (usable)
[    0.000000]  modified: 00000000c7ea0000 - 00000000c7ebc000 (ACPI data)
[    0.000000]  modified: 00000000c7ebc000 - 00000000c7ebe000 (ACPI NVS)
[    0.000000]  modified: 00000000c7ebe000 - 00000000c8000000 (reserved)
[    0.000000]  modified: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000]  modified: 0000000100000000 - 0000000138000000 (usable)
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] found SMP MP-table at [ffff8800000f8080] f8080
[    0.000000] Using GB pages for direct mapping
[    0.000000] init_memory_mapping: 0000000000000000-00000000c7ea0000
[    0.000000]  0000000000 - 00c0000000 page 1G
[    0.000000]  00c0000000 - 00c7e00000 page 2M
[    0.000000]  00c7e00000 - 00c7ea0000 page 4k
[    0.000000] kernel direct mapping tables up to c7ea0000 @ 16000-19000
[    0.000000] init_memory_mapping: 0000000100000000-0000000138000000
[    0.000000]  0100000000 - 0138000000 page 2M
[    0.000000] kernel direct mapping tables up to 138000000 @ 18000-1a000
[    0.000000] RAMDISK: 37117000 - 37ff0000
[    0.000000] ACPI: RSDP 00000000000f7ff0 00024 (v02 PTLTD )
[    0.000000] ACPI: XSDT 00000000c7eb0005 0005C (v01 SECCSD LH43STAR 06040000  LTP 00000000)
[    0.000000] ACPI: FACP 00000000c7ebb898 000F4 (v03 SEC    MAGIC    06040000 ATI  000F4240)
[    0.000000] ACPI: DSDT 00000000c7eb0061 0B837 (v01    ATI    SB700 06040000 MSFT 03000001)
[    0.000000] ACPI: FACS 00000000c7ebdfc0 00040
[    0.000000] ACPI: TCPA 00000000c7ebba00 00032 (v02 AMD             06040000 PTEC 00000000)
[    0.000000] ACPI: SSDT 00000000c7ebba32 00386 (v01 AMD    POWERNOW 06040000 AMD  00000001)
[    0.000000] ACPI: SLIC 00000000c7ebbdb8 00176 (v01 SECCSD LH43STAR 06040000  LTP 00000000)
[    0.000000] ACPI: APIC 00000000c7ebbf2e 0005E (v01 PTLTD  ? APIC   06040000  LTP 00000000)
[    0.000000] ACPI: MCFG 00000000c7ebbf8c 0003C (v01 PTLTD    MCFG   06040000  LTP 00000000)
[    0.000000] ACPI: HPET 00000000c7ebbfc8 00038 (v01 PTLTD  HPETTBL  06040000  LTP 00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] Scanning NUMA topology in Northbridge 24
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000138000000
[    0.000000] Initmem setup node 0 0000000000000000-0000000138000000
[    0.000000]   NODE_DATA [0000000100000000 - 0000000100004fff]
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880100200000-ffff880103bfffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00138000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009d
[    0.000000]     0: 0x00000100 -> 0x000c7ea0
[    0.000000]     0: 0x00100000 -> 0x00138000
[    0.000000] On node 0 totalpages: 1048109
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3925 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 800472 pages, LIFO batch:31
[    0.000000]   Normal zone: 3136 pages used for memmap
[    0.000000]   Normal zone: 226240 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x8008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x43538301 base: 0xfed00000
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] early_res array is doubled to 64 at [19000 - 197ff]
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[    0.000000] PM: Registered nosave memory: 00000000000d0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000c7ea0000 - 00000000c7ebc000
[    0.000000] PM: Registered nosave memory: 00000000c7ebc000 - 00000000c7ebe000
[    0.000000] PM: Registered nosave memory: 00000000c7ebe000 - 00000000c8000000
[    0.000000] PM: Registered nosave memory: 00000000c8000000 - 00000000e0000000
[    0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[    0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[    0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[    0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000fff00000
[    0.000000] PM: Registered nosave memory: 00000000fff00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at c8000000 (gap: c8000000:18000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1
[    0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001e00000 s91392 r8192 d23296 u1048576
[    0.000000] pcpu-alloc: s91392 r8192 d23296 u1048576 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 0 1 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1030637
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.35-020635rc4-generic root=/dev/mapper/pool01-root ro console=ttyUSB0,9600n8 console=tty0
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Node 0: aperture @ 20000000 size 32 MB
[    0.000000] Aperture pointing to e820 RAM. Ignoring.
[    0.000000] Your BIOS doesn't leave a aperture memory hole
[    0.000000] Please enable the IOMMU option in the BIOS setup
[    0.000000] This costs you 64 MB of RAM
[    0.000000] Mapping aperture over 65536 KB of RAM @ 20000000
[    0.000000] PM: Registered nosave memory: 0000000020000000 - 0000000024000000
[    0.000000] early_res array is doubled to 128 at [19800 - 1a7ff]
[    0.000000] Subtract (58 early reservations)
[    0.000000]   #1 [0001000000 - 0001d30a14]   TEXT DATA BSS
[    0.000000]   #2 [0037117000 - 0037ff0000]         RAMDISK
[    0.000000]   #3 [0001d31000 - 0001d311e4]             BRK
[    0.000000]   #4 [00000f8090 - 0000100000]   BIOS reserved
[    0.000000]   #5 [00000f8080 - 00000f8090]    MP-table mpf
[    0.000000]   #6 [000009dc00 - 000009e171]   BIOS reserved
[    0.000000]   #7 [000009e2ed - 00000f8080]   BIOS reserved
[    0.000000]   #8 [000009e171 - 000009e2ed]    MP-table mpc
[    0.000000]   #9 [0000010000 - 0000012000]      TRAMPOLINE
[    0.000000]   #10 [0000012000 - 0000016000]     ACPI WAKEUP
[    0.000000]   #11 [0000016000 - 0000018000]         PGTABLE
[    0.000000]   #12 [0000018000 - 0000019000]         PGTABLE
[    0.000000]   #13 [0100000000 - 0100005000]       NODE_DATA
[    0.000000]   #14 [0001d31200 - 0001d32200]         BOOTMEM
[    0.000000]   #15 [0001d30a40 - 0001d30d40]         BOOTMEM
[    0.000000]   #16 [0100005000 - 0100006000]         BOOTMEM
[    0.000000]   #17 [0100006000 - 0100007000]         BOOTMEM
[    0.000000]   #18 [0100200000 - 0103c00000]        MEMMAP 0
[    0.000000]   #19 [0001d30d40 - 0001d30ec0]         BOOTMEM
[    0.000000]   #20 [0001d32200 - 0001d4a200]         BOOTMEM
[    0.000000]   #21 [0001d4a200 - 0001d50200]         BOOTMEM
[    0.000000]   #22 [0001d51000 - 0001d52000]         BOOTMEM
[    0.000000]   #23 [0001d30ec0 - 0001d30f01]         BOOTMEM
[    0.000000]   #24 [0001d30f40 - 0001d30f83]         BOOTMEM
[    0.000000]   #25 [0001d50200 - 0001d504d8]         BOOTMEM
[    0.000000]   #26 [0001d50500 - 0001d50568]         BOOTMEM
[    0.000000]   #27 [0001d50580 - 0001d505e8]         BOOTMEM
[    0.000000]   #28 [0001d50600 - 0001d50668]         BOOTMEM
[    0.000000]   #29 [0001d50680 - 0001d506e8]         BOOTMEM
[    0.000000]   #30 [0001d50700 - 0001d50768]         BOOTMEM
[    0.000000]   #31 [0001d50780 - 0001d507e8]         BOOTMEM
[    0.000000]   #32 [0001d50800 - 0001d50868]         BOOTMEM
[    0.000000]   #33 [0001d50880 - 0001d508e8]         BOOTMEM
[    0.000000]   #34 [0001d50900 - 0001d50968]         BOOTMEM
[    0.000000]   #35 [0001d50980 - 0001d509e8]         BOOTMEM
[    0.000000]   #36 [0001d50a00 - 0001d50a68]         BOOTMEM
[    0.000000]   #37 [0001d50a80 - 0001d50ae8]         BOOTMEM
[    0.000000]   #38 [0001d30fc0 - 0001d30fe0]         BOOTMEM
[    0.000000]   #39 [0001d50b00 - 0001d50b20]         BOOTMEM
[    0.000000]   #40 [0001d50b40 - 0001d50bb1]         BOOTMEM
[    0.000000]   #41 [0001d50bc0 - 0001d50c31]         BOOTMEM
[    0.000000]   #42 [0001e00000 - 0001e1e000]         BOOTMEM
[    0.000000]   #43 [0001f00000 - 0001f1e000]         BOOTMEM
[    0.000000]   #44 [0001d50c40 - 0001d50c48]         BOOTMEM
[    0.000000]   #45 [0001d50c80 - 0001d50c88]         BOOTMEM
[    0.000000]   #46 [0001d50cc0 - 0001d50cc8]         BOOTMEM
[    0.000000]   #47 [0001d50d00 - 0001d50d10]         BOOTMEM
[    0.000000]   #48 [0001d50d40 - 0001d50e80]         BOOTMEM
[    0.000000]   #49 [0001d50e80 - 0001d50ee0]         BOOTMEM
[    0.000000]   #50 [0001d50f00 - 0001d50f60]         BOOTMEM
[    0.000000]   #51 [0001d52000 - 0001d5a000]         BOOTMEM
[    0.000000]   #52 [0020000000 - 0024000000]         BOOTMEM
[    0.000000]   #53 [0001d50f80 - 0001d50fa0]         BOOTMEM
[    0.000000]   #54 [0001f1e000 - 0005f1e000]         BOOTMEM
[    0.000000]   #55 [0001d5a000 - 0001d7a000]         BOOTMEM
[    0.000000]   #56 [0001d7a000 - 0001dba000]         BOOTMEM
[    0.000000]   #57 [000001a800 - 0000022800]         BOOTMEM
[    0.000000] Memory: 3972372k/5111808k available (5637k kernel code, 919372k absent, 220064k reserved, 5486k data, 976k init)
[    0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] 	RCU-based detection of stalled CPUs is disabled.
[    0.000000] 	Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:4352 nr_irqs:512
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] allocated 41943040 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2094.734 MHz processor.
[    0.030010] Calibrating delay loop (skipped), value calculated using timer frequency.. 4189.46 BogoMIPS (lpj=20947310)
[    0.030094] pid_max: default: 32768 minimum: 301
[    0.030156] Security Framework initialized
[    0.030201] SELinux:  Disabled at boot.
[    0.030698] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.041268] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.041990] Mount-cache hash table entries: 256
[    0.042159] Initializing cgroup subsys ns
[    0.042236] Initializing cgroup subsys cpuacct
[    0.042279] Initializing cgroup subsys memory
[    0.042327] Initializing cgroup subsys devices
[    0.042369] Initializing cgroup subsys freezer
[    0.042410] Initializing cgroup subsys net_cls
[    0.042474] tseg: 00c7f00000
[    0.042477] CPU: Physical Processor ID: 0
[    0.042518] CPU: Processor Core ID: 0
[    0.042559] mce: CPU supports 6 MCE banks
[    0.042608] using C1E aware idle routine
[    0.042649] Performance Events: AMD PMU driver.
[    0.042728] ... version:                0
[    0.042769] ... bit width:              48
[    0.042809] ... generic registers:      4
[    0.042850] ... value mask:             0000ffffffffffff
[    0.042891] ... max period:             00007fffffffffff
[    0.042932] ... fixed-purpose events:   0
[    0.042972] ... event mask:             000000000000000f
[    0.044836] ACPI: Core revision 20100428
[    0.060027] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.060081] ftrace: allocating 26474 entries in 104 pages
[    0.070088] Setting APIC routing to flat
[    0.070514] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.173493] CPU0: AMD Athlon(tm) II Dual-Core M320 stepping 02
[    0.180000] Booting Node   0, Processors  #1 Ok.
[    0.340007] Brought up 2 CPUs
[    0.340022] System has AMD C1E enabled
[    0.340041] Switch to broadcast mode on CPU1
[    0.340163] Total of 2 processors activate CPU0
[    0.340414] devtmpfs: initialized
[    0.340748] regulator: core version 0.5
[    0.340854] Time: 17:02:00  Date: 07/09/10
[    0.340935] NET: Registered protocol family 16
[    0.341120] node 0 link 0: io port [1000, ffff]
[    0.341123] TOM: 000i 0000:00:12.1: reg 10: [mem 0xf0405000-0xf0405fff]
[    0.355245] pci 0000:00:12.2: reg 10: [mem 0xf0409400-0xf04094ff]
[    0.355297] pci 0000:00:12.2: supports D1 D2
[    0.355299] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.355303] pci 0000:00:12.2: PME# disabled
[    0.355334] pci 0000:00:13.0: reg 10: [mem 0xf0406000-0xf0406fff]
[    0.355387] pci 0000:00:13.1: reg 10: [mem 0xf0407000-0xf0407fff]
[    0.355452] pci 0000:00:13.2: reg 10: [mem 0xf0409800-0xf04098ff]
[    0.355504] pci 0000:00:13.2: supports D1 D2
[    0.355506] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[    0.355510] pci 0000:00:13.2: PME# disabled
[    0.355626] pci 0000:00:14.2: reg 10: [mem 0xf0400000-0xf0403fff 64bit]
[    0.355669] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.355673] pci 0000:00:14.2: PME# disabled
[    0.355775] pci 0000:00:14.5: reg 10: [mem 0xf0408000-0xf0408fff]
[    0.355968] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.355977] pci 0000:01:00.0: reg 18: [mem 0xcfee0000-0xcfefffff 64bit]
[    0.355982] pci 0000:01:00.0: reg 20: [io  0x9000-0x90ff]
[    0.355991] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[    0.356008] pci 0000:01:00.0: supports D1 D2
[    0.356039] pci 0000:01:00.1: reg 10: [mem 0xcfedc000-0xcfedffff 64bit]
[    0.356071] pci 0000:01:00.1: supports D1 D2
[    0.380035] pci 0000:00:02.0: PCI bridge to [bus 01-01]
[    0.380083] pci 0000:00:02.0:   bridge window [io  0x9000-0x9fff]
[    0.380087] pci 0000:00:02.0:   bridge window [mem 0xcfe00000-0xcfefffff]
[    0.380091] pci 0000:00:02.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.380152] pci 0000:02:00.0: reg 10: [mem 0xf0200000-0xf020ffff 64bit]
[    0.380203] pci 0000:02:00.0: supports D1
[    0.380206] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
[    0.380210] pci 0000:02:00.0: PME# disabled
[    0.410034] pci 0000:00:04.0: PCI bridge to [bus 02-02]
[    0.410083] pci 0000:00:04.0:   bridge window [io  0xf000-0x0000] (disabled)
[    0.410087] pci 0000:00:04.0:   bridge window [mem 0xf0200000-0xf02fffff]
[    0.410091] pci 0000:00:04.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.410122] pci 0000:00:05.0: PCI bridge to [bus 03-03]
[    0.410165] pci 0000:00:05.0:   bridge window [io  0x0000-0x0000] (disabled)
[    0.410168] pci 0000:00:05.0:   bridge window [mem 0x00000000-0x000fffff] (disabled)
[    0.410172] pci 0000:00:05.0:   bridge window [mem 0x00000000-0x000fffff pref] (disabled)
[    0.410268] pci 0000:04:00.0: reg 10: [mem 0xf0300000-0xf0303fff 64bit]
[    0.410275] pci 0000:04:00.0: reg 18: [io  0xa000-0xa0ff]
[    0.410369] pci 0000:04:00.0: supports D1 D2
[    0.410372] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.410377] pci 0000:04:00.0: PME# disabled
[    0.440074] pci 0000:00:06.0: PCI bridge to [bus 04-04]
[    0.440157] pci 0000:00:06.0:   bridge window [io  0xa000-0xafff]
[    0.440160] pci 0000:00:06.0:   bridge window [mem 0xf0300000-0xf03fffff]
[    0.440164] pci 0000:00:06.0:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.440233] pci 0000:00:14.4: PCI bridge to [bus 05-05] (subtractive decode)
[    0.440278] pci 0000:00:14.4:   bridge window [io  0xf000-0x0000] (disabled)
[    0.440283] pci 0000:00:14.4:   bridge window [mem 0xfff00000-0x000fffff] (disabled)
[    0.440287] pci 0000:00:14.4:   bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[    0.440290] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.440292] pci 0000:00:14.4:   bridge window [mem 0x000d0000-0x000d1fff] (subtractive decode)
[    0.440295] pci 0000:00:14.4:   bridge window [mem 0x000d2000-0x000d3fff] (subtractive decode)
[    0.440297] pci 0000:00:14.4:   bridge window [mem 0x000d4000-0x000d5fff] (subtractive decode)
[    0.440299] pci 0000:00:14.4:   bridge window [mem 0x000d6000-0x000d7fff] (subtractive decode)
[    0.440302] pci 0000:00:14.4:   bridge window [mem 0x000d8000-0x000d9fff] (subtractive decode)
[    0.440304] pci 0000:00:14.4:   bridge window [mem 0x000da000-0x000dbfff] (subtractive decode)
[    0.440306] pci 0000:00:14.4:   bridge window [mem 0x000dc000-0x000ddfff] (subtractive decode)
[    0.440308] pci 0000:00:14.4:   bridge window [mem 0xc8000000-0xdfffffff] (subtractive decode)
[    0.440311] pci 0000:00:14.4:   bridge window [mem 0xf0000000-0xffffffff] (subtractive decode)
[    0.440313] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.440315] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.440339] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.440579] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB2_._PRT]
[    0.440664] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[    0.440735] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[    0.440804] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
[    0.440922] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.445363] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[    0.445765] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[    0.446158] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[    0.446550] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[    0.446943] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[    0.447335] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[    0.447727] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[    0.448119] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[    0.448407] HEST: Table is not found!
[    0.448532] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.448612] vgaarb: loaded
[    0.448786] SCSI subsystem initialized
[    0.450045] libata version 3.00 loaded.
[    0.450047] usbcore: registered new interface driver usbfs
[    0.450131] usbcore: registered new interface driver hub
[    0.450181] usbcore: registered new device driver usb
[    0.450181] ACPI: WMI: Mapper loaded
[    0.450181] PCI: Using ACPI for IRQ routing
[    0.450205] PCI: pci_cache_line_size set to 64 bytes
[    0.450384] reserve RAM buffer: 000000000009dc00 - 000000000009ffff 
[    0.450387] reserve RAM buffer: 00000000c7ea0000 - 00000000c7ffffff 
[    0.450394] NetLabel: Initializing
[    0.450394] NetLabel:  domain hash size = 128
[    0.450394] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.450394] NetLabel:  unlabeled traffic allowed by default
[    0.450394] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.450559] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
[    0.452631] Switching to clocksource tsc
[    0.467732] pnp: PnP ACPI init
[    0.467827] ACPI: bus type pnp registered
[    0.471817] pnp: PnP ACPI: found 11 devices
[    0.471897] ACPI: ACPI bus type pnp unregistered
[    0.471955] system 00:01: [io  0x0f50-0x0f51] has been reserved
[    0.472000] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.472042] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.472091] system 00:08: [io  0x0220-0x022f] has been reserved
[    0.472132] system 00:08: [io  0x040b] has been reserved
[    0.472174] system 00:08: [io  0x04d0-0x04d1] has been reserved
[    0.472215] system 00:08: [io  0x04d6] has been reserved
[    0.472257] system 00:08: [io  0x0530-0x0537] has been reserved
[    0.472299] system 00:08: [io  0x0c00-0x0c01] has been reserved
[    0.472340] system 00:08: [io  0x0c14] has been reserved
[    0.472382] system 00:08: [io  0x0c50-0x0c52] has been reserved
[    0.472424] system 00:08: [io  0x0c6c] has been reserved
[    0.472465] system 00:08: [io  0x0c6f] has been reserved
[    0.472507] system 00:08: [io  0x0cd0-0x0cd1] has been reserved
[    0.472548] system 00:08: [io  0x0cd2-0x0cd3] has been reserved
[    0.472589] system 00:08: [io  0x0cd4-0x0cd5] has been reserved
[    0.472631] system 00:08: [io  0x0cd6-0x0cd7] has been reserved
[    0.472673] system 00:08: [io  0x0cd8-0x0cdf] has been reserved
[    0.472715] system 00:08: [io  0x8000-0x805f] has been reserved
[    0.472757] system 00:08: [io  0x8100-0x81ff window] has been reserved
[    0.472799] system 00:08: [io  0x8200-0x82ff window] has been reserved
[    0.472841] system 00:08: [io  0x0f40-0x0f47] has been reserved
[    0.472883] system 00:08: [io  0x087f] has been reserved
[    0.472928] system 00:09: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.472971] system 00:09: [mem 0xffe00000-0xffffffff] could not be reserved
[    0.473013] system 00:09: [mem 0xfec10000-0xfec1001f] has been reserved
[    0.478132] pci 0000:00:05.0: BAR 14: assigned [mem 0xc8000000-0xc81fffff]
[    0.478177] pci 0000:00:05.0: BAR 15: assigned [mem 0xc8200000-0xc83fffff 64bit pref]
[    0.478224] pci 0000:00:05.0: BAR 13: assigned [io  0x1000-0x1fff]
[    0.478268] pci 0000:01:00.0: BAR 6: assigned [mem 0xcfe00000-0xcfe1ffff pref]
[    0.478313] pci 0000:00:02.0: PCI bridge to [bus 01-01]
[    0.478354] pci 0000:00:02.0:   bridge window [io  0x9000-0x9fff]
[    0.478397] pci 0000:00:02.0:   bridge window [mem 0xcfe00000-0xcfefffff]
[    0.478440] pci 0000:00:02.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.478487] pci 0000:00:04.0: PCI bridge to [bus 02-02]
[    0.478528] pci 0000:00:04.0:   bridge window [io  disabled]
[    0.478570] pci 0000:00:04.0:   bridge window [mem 0xf0200000-0xf02fffff]
[    0.478612] pci 0000:00:04.0:   bridge window [mem pref disabled]
[    0.478655] pci 0000:00:05.0: PCI bridge to [bus 03-03]
[    0.478697] pci 0000:00:05.0:   bridge window [io  0x1000-0x1fff]
[    0.478740] pci 0000:00:05.0:   bridge window [mem 0xc8000000-0xc81fffff]
[    0.478782] pci 0000:00:05.0:   bridge window [mem 0xc8200000-0xc83fffff 64bit pref]
[    0.478829] pci 0000:00:06.0: PCI bridge to [bus 04-04]
[    0.478871] pci 0000:00:06.0:   bridge window [io  0xa000-0xafff]
[    0.479543] pci 0000:00:06.0:   bridge window [mem 0xf0300000-0xf03fffff]
[    0.479586] pci 0000:00:06.0:   bridge window [mem pref disabled]
[    0.479629] pci 0000:00:14.4: PCI bridge to [bus 05-05]
[    0.479670] pci 0000:00:14.4:   bridge window [io  disabled]
[    0.479714] pci 0000:00:14.4:   bridge window [mem disabled]
[    0.479757] pci 0000:00:14.4:   bridge window [mem pref disabled]
[    0.479810]   alloc irq_desc for 18 on node 0
[    0.479813]   alloc kstat_irqs on node 0
[    0.479820] pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.479864] pci 0000:00:02.0: setting latency timer to 64
[    0.479869]   alloc irq_desc for 16 on node 0
[    0.479871]   alloc kstat_irqs on node 0
[    0.479874] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.479917] pci 0000:00:04.0: setting latency timer to 64
[    0.479922] pci 0000:00:05.0: enabling device (0000 -> 0003)
[    0.479964]   alloc irq_desc for 17 on node 0
[    0.479966]   alloc kstat_irqs on node 0
[    0.479969] pci 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.480012] pci 0000:00:05.0: setting latency timer to 64
[    0.480018] pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.480060] pci 0000:00:06.0: setting latency timer to 64
[    0.480069] pci_bus 0000:00: resource 4 [mem 0x000a0000-0x000bffff]
[    0.480071] pci_bus 0000:00: resource 5 [mem 0x000d0000-0x000d1fff]
[    0.480074] pci_bus 0000:00: resource 6 [mem 0x000d2000-0x000d3fff]
[    0.480076] pci_bus 0000:00: resource 7 [mem 0x000d4000-0x000d5fff]
[    0.480079] pci_bus 0000:00: resource 8 [mem 0x000d6000-0x000d7fff]
[    0.480081] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000d9fff]
[    0.480084] pci_bus 0000:00: resource 10 [mem 0x000da000-0x000dbfff]
[    0.480086] pci_bus 0000:00: resource 11 [mem 0x000dc000-0x000ddfff]
[    0.480089] pci_bus 0000:00: resource 12 [mem 0xc8000000-0xdfffffff]
[    0.480091] pci_bus 0000:00: resource 13 [mem 0xf0000000-0xffffffff]
[    0.480094] pci_bus 0000:00: resource 14 [io  0x0000-0x0cf7]
[    0.480096] pci_bus 0000:00: resource 15 [io  0x0d00-0xffff]
[    0.480099] pci_bus 0000:01: resource 0 [io  0x9000-0x9fff]
[    0.480101] pci_bus 0000:01: resource 1 [mem 0xcfe00000-0xcfefffff]
[    0.480104] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.480106] pci_bus 0000:02: resource 1 [mem 0xf0200000-0xf02fffff]
[    0.480109] pci_bus 0000:03: resource 0 [io  0x1000-0x1fff]
[    0.480111] pci_bus 0000:03: resource 1 [mem 0xc8000000-0xc81fffff]
[    0.480114] pci_bus 0000:03: resource 2 [mem 0xc8200000-0xc83fffff 64bit pref]
[    0.480117] pci_bus 0000:04: resource 0 [io  0xa000-0xafff]
[    0.480119] pci_bus 0000:04: resource 1 [mem 0xf0300000-0xf03fffff]
[    0.480122] pci_bus 0000:05: resource 4 [mem 0x000a0000-0x000bffff]
[    0.480124] pci_bus 0000:05: resource 5 [mem 0x000d0000-0x000d1fff]
[    0.480126] pci_bus 0000:05: resource 6 [mem 0x000d2000-0x000d3fff]
[    0.480129] pci_bus 0000:05: resource 7 [mem 0x000d4000-0x000d5fff]
[    0.480131] pci_bus 0000:05: resource 8 [mem 0x000d6000-0x000d7fff]
[    0.480134] pci_bus 0000:05: resource 9 [mem 0x000d8000-0x000d9fff]
[    0.480136] pci_bus 0000:05: resource 10 [mem 0x000da000-0x000dbfff]
[    0.480139] pci_bus 0000:05: resource 11 [mem 0x000dc000-0x000ddfff]
[    0.480141] pci_bus 0000:05: resource 12 [mem 0xc8000000-0xdfffffff]
[    0.480144] pci_bus 0000:05: resource 13 [mem 0xf0000000-0xffffffff]
[    0.480146] pci_bus 0000:05: resource 14 [io  0x0000-0x0cf7]
[    0.480148] pci_bus 0000:05: resource 15 [io  0x0d00-0xffff]
[    0.480183] NET: Registered protocol family 2
[    0.480400] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.481649] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.484878] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.485330] TCP: Hash tables configured (established 524288 bind 65536)
[    0.485408] TCP reno registered
[    0.485462] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    0.485540] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    0.485724] NET: Registered protocol family 1
[    0.485964] pci 0000:01:00.0: Boot video device
[    0.485991] PCI: CLS 32 bytes, default 64
[    0.486046] Trying to unpack rootfs image as initramfs...
[    0.825588] Freeing initrd memory: 15204k freed
[    0.831516] PCI-DMA: Disabling AGP.
[    0.831665] PCI-DMA: aperture base @ 20000000 size 65536 KB
[    0.831708] PCI-DMA: using GART IOMMU.
[    0.831749] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[    0.835233] Scanning for low memory corruption every 60 seconds
[    0.835419] audit: initializing netlink socket (disabled)
[    0.835504] type=2000 audit(1278694919.820:1): initialized
[    0.850282] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.851726] VFS: Disk quotas dquot_6.5.2
[    0.851835] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.852510] fuse init (API version 7.14)
[    0.852699] msgmni has been set to 7917
[    0.853034] alg: No test for stdrng (krng)
[    0.853211] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.853282] io scheduler noop registered
[    0.853322] io scheduler deadline registered
[    0.853400] io scheduler cfq registered (default)
[    0.853656] pcieport 0000:00:02.0: setting latency timer to 64
[    0.853679]   alloc irq_desc for 40 on node 0
[    0.853681]   alloc kstat_irqs on node 0
[    0.853690] pcieport 0000:00:02.0: irq 40 for MSI/MSI-X
[    0.853817] pcieport 0000:00:04.0: setting latency timer to 64
[    0.853836]   alloc irq_desc for 41 on node 0
[    0.853838]   alloc kstat_irqs on node 0
[    0.853843] pcieport 0000:00:04.0: irq 41 for MSI/MSI-X
[    0.853944] pcieport 0000:00:05.0: setting latency timer to 64
[    0.853963]   alloc irq_desc for 42 on node 0
[    0.853965]   alloc kstat_irqs on node 0
[    0.853969] pcieport 0000:00:05.0: irq 42 for MSI/MSI-X
[    0.854080] pcieport 0000:00:06.0: setting latency timer to 64
[    0.854099]   alloc irq_desc for 43 on node 0
[    0.854101]   alloc kstat_irqs on node 0
[    0.854106] pcieport 0000:00:06.0: irq 43 for MSI/MSI-X
[    0.854223] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.854354] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.855160] ACPI: AC Adapter [ACAD] (on-line)
[    0.855310] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.855395] ACPI: Power Button [PWRB]
[    0.855485] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[    0.855565] ACPI: Sleep Button [SLPB]
[    0.855636] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[    0.856010] ACPI: Lid Switch [LID]
[    0.856158] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[    0.856238] ACPI: Power Button [PWRF]
[    0.856474] ACPI: acpi_idle registered with cpuidle
[    0.856502] ACPI: processor limited to max C-state 1
[    0.861070] thermal LNXTHERM:01: registered as thermal_zone0
[    0.861157] ACPI: Thermal Zone [THZ0] (58 C)
[    0.861280] ERST: Table is not found!
[    0.861683] ACPI: Battery Slot [BATT] (battery absent)
[    0.862673] Linux agpgart interface v0.103
[    0.862754] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.863847] brd: module loaded
[    0.864312] loop: module loaded
[    0.864840] Fixed MDIO Bus: probed
[    0.864941] PPP generic driver version 2.4.2
[    0.865010] tun: Universal TUN/TAP device driver, 1.6
[    0.865051] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.865165] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.865378] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.865470] ehci_hcd 0000:00:12.2: EHCI Host Controller
[    0.865578] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[    0.865703] ehci_hcd 0000:00:12.2: debug port 1
[    0.865768] ehcicted
[    0.877823]   alloc irq_desc for 19 on node 0
[    0.877826]   alloc kstat_irqs on node 0
[    0.877834] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.877899] ehci_hcd 0000:00:13.2: EHCI Host Controller
[    0.877978] ehcOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.212870] EDD information not available.
[    1.212981] Freeing unused kernel memory: 976k freed
[    1.213335] Write protecting the kernel read-only data: 10240k
[    1.213570] Freeing unused kernel memory: 488k freed
[    1.213887] Freeing unused kernel memory: 1532k freed
[    1.237253] udev: starting version 151
[    1.242434] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    1.276613] sky2: driver version 1.28
[    1.295243] sky2 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.295372] sky2 0000:04:00.0: setting latency timer to 64
[    1.295460] sky2 0000:04:00.0: Yukon-2 FE+ chip revision 0
[    1.295596]   alloc irq_desc for 44 on node 0
[    1.295598]   alloc kstat_irqs on node 0
[    1.295633] sky2 0000:04:00.0: irq 44 for MSI/MSI-X
[    1.300721] sky2 0000:04:00.0: eth0: addr 00:24:54:6e:90:bf
[    1.322602] usb 2-3: new high speed USB device using ehci_hcd and address 2
[    1.336712] ahci 0000:00:11.0: version 3.0
[    1.336766]   alloc irq_desc for 22 on node 0
[    1.336769]   alloc kstat_irqs on node 0
[    1.336778] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.336994] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0xb impl SATA mode
[    1.337041] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc sxs 
[    1.349002] [Firmware Bug]: ACPI: ACPI brightness control misses _BQC function
[    1.354812] scsi0 : ahci
[    1.358819] scsi1 : ahci
[    1.360103] scsi2 : ahci
[    1.360276] scsi3 : ahci
[    1.361694] ata1: SATA max UDMA/133 abar m1024@0xf0409000 port 0xf0409100 irq 22
[    1.361740] ata2: SATA max UDMA/133 abar m1024@0xf0409000 port 0xf0409180 irq 22
[    1.361756] acpi device:02: registered as cooling_device2
[    1.361824] ata3: DUMMY
[    1.361865] ata4: SATA max UDMA/133 abar m1024@0xf0409000 port 0xf0409280 irq 22
[    1.362019] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input5
[    1.362126] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    1.710110] ata4: SATA link down (SStatus 0 SControl 300)
[    1.800099] usb 3-1: new full speed USB device using ohci_hcd and address 2
[    1.910118] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.910191] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.911662] ata2.00: ATAPI: TSSTcorp CDDVDW TS-L633C, SC00, max UDMA/100
[    1.911717] ata2.00: applying bridge limits
[    1.915164] ata2.00: configured for UDMA/100
[    1.916178] ata1.00: ATA-8: SAMSUNG HM321HI, 2AJ10001, max UDMA/133
[    1.916225] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    1.922081] ata1.00: configured for UDMA/133
[    1.942812] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM321HI  2AJ1 PQ: 0 ANSI: 5
[    1.943045] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    1.943159] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    1.943274] sd 0:0:0:0: [sda] Write Protect is off
[    1.943359] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.943376] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.943548]  sda:
[    1.950051] scsi 1:0:0:0: CD-ROM            TSSTcorp CDDVDW TS-L633C  SC00 PQ: 0 ANSI: 5
[    1.955031] sr0: scsi3-mmc drive: 31x/62x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.955081] Uniform CD-ROM driver Revision: 3.20
[    1.955248] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    1.955305] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    1.969254]  sda1 sda2 sda3 sda4 < sda5 sda6 >
[    1.997592] sd 0:0:0:0: [sda] Attached SCSI disk
[   64.930341] Intel AES-NI instructions are not detected.
[   65.937815] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[   77.786154] udev: starting version 151
[   77.814768] Adding 3903484k swap on /dev/mapper/pool01-swap.  Priority:-1 extents:1 across:3903484k 
[   78.196198] EDAC MC: Ver: 2.1.0 Jul  5 2010
[   78.214506] ACPI: resource piix4_smbus [io  0x8040-0x8047] conflicts with ACPI region SMB0 [mem 0x00008040-0x0000804f 64bit window disabled]
[   78.214510] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   78.244077] EDAC amd64_edac:  Ver: 3.3.0 Jul  5 2010
[   78.245729] lp: driver loaded but no devices found
[   78.248326] EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3).
[   78.248342] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[   78.248344]  Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[   78.248345]  (Note that use of the override may cause unknown side effects.)
[   78.248383] amd64_edac: probe of 0000:00:18.2 failed with error -22
[   78.267420] usbcore: registered new interface driver usbserial
[   78.267435] USB Serial support registered for generic
[   78.267756] usbcore: registered new interface driver usbserial_generic
[   78.267759] usbserial: USB Serial Driver core
[   78.316182] USB Serial support registered for pl2303
[   78.316209] pl2303 3-1:1.0: pl2303 converter detected
[   78.335199] cfg80211: Calling CRDA to update world regulatory domain
[   78.338209] usb 3-1: pl2303 converter now attached to ttyUSB0
[   78.338229] usbcore: registered new interface driver pl2303
[   78.338232] pl2303: Prolific PL2303 USB to serial adaptor driver
[   78.417292] cfg80211: World regulatory domain updated:
[   78.417296]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   78.417300]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   78.417302]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   78.417305]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   78.417307]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   78.417309]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   78.634335] Linux video capture interface: v2.00
[   78.686693] uvcvideo: Found UVC 1.00 device USB 2.0 PC Camera (1210:25f4)
[   78.689737] input: USB 2.0 PC Camera as /devices/pci0000:00/0000:00:13.2/usb2/2-3/2-3:1.0/input/input6
[   78.689789] usbcore: registered new interface driver uvcvideo
[   78.689792] USB Video Class driver (v0.1.0)
[   78.991424] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04731/0xa40000/0xa0000
[   79.032933] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[   79.196967] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   79.242084] ath9k 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   79.242094] ath9k 0000:02:00.0: setting latency timer to 64
[   79.291883] ath: EEPROM regdomain: 0x65
[   79.291885] ath: EEPROM indicates we should expect a direct regpair map
[   79.291890] ath: Country alpha2 being used: 00
[   79.291891] ath: Regpair used: 0x65
[   79.372393] phy0: Selected rate control algorithm 'ath9k_rate_control'
[   79.372989] Registered led device: ath9k-phy0::radio
[   79.373003] Registered led device: ath9k-phy0::assoc
[   79.373018] Registered led device: ath9k-phy0::tx
[   79.373031] Registered led device: ath9k-phy0::rx
[   79.373039] phy0: Atheros AR9285 Rev:2 mem=0xffffc90001600000, irq=16
[   79.665780] hda_codec: ALC269: BIOS auto-probing.
[   79.669000] HDA Intel 0000:01:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   79.669073]   alloc irq_desc for 45 on node 0
[   79.669075]   alloc kstat_irqs on node 0
[   79.669087] HDA Intel 0000:01:00.1: irq 45 for MSI/MSI-X
[   79.669114] HDA Intel 0000:01:00.1: setting latency timer to 64
[   80.202897] EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
[   80.706092] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[   82.266351] ppdev: user-space parallel port driver
[   91.093692] Xorg:1151 freeing invalid memtype d0000000-e0000000
[  469.555940] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  469.683481] sky2 0000:04:00.0: eth0: enabling interface
[  469.686128] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  471.243013] sky2 0000:04:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx
[  471.245517] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  481.722623] eth0: no IPv6 routers present
[ 1661.793497] modprobe:3342 freeing invalid memtype f0200000-f0210000
[ 1661.793554] ath9k 0000:02:00.0: PCI INT A disabled
[ 1661.793748] ath9k: Driver unloaded
[ 1666.546339] PM: Syncing filesystems ... done.
[ 1668.111070] PM: Preparing system for mem sleep
[ 1668.111077] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 1668.130103] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 1668.150108] PM: Entering mem sleep
[ 1668.150125] Suspending console(s) (use no_console_suspend to debug)
[ 1668.150460] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 1668.174958] sd 0:0:0:0: [sda] Stopping disk
[ 1668.198045] ACPI handle has no context!
[ 1668.199302] ohci_hcd 0000:00:14.5: PCI INT C disabled
[ 1668.199468] ohci_hcd 0000:00:13.1: PCI INT A disabled
[ 1668.199477] ohci_hcd 0000:00:13.0: PCI INT A disabled
[ 1668.199520] ehci_hcd 0000:00:12.2: PCI INT B disabled
[ 1668.199525] ohci_hcd 0000:00:12.1: PCI INT A disabled
[ 1668.199562] ohci_hcd 0000:00:12.0: PCI INT A disabled
[ 1668.210138] ehci_hcd 0000:00:13.2: PCI INT B disabled
[ 1668.300295] HDA Intel 0000:00:14.2: PCI INT A disabled
[ 1668.300301] HDA Intel 0000:01:00.1: PCI INT B disabled
[ 1668.300349] ACPI handle has no context!
[ 1669.700139] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1674.700125] ata1.00: qc timeout (cmd 0xec)
[ 1674.700136] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 1674.700139] ata1.00: revalidation failed (errno=-5)
[ 1675.230136] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1685.230125] ata1.00: qc timeout (cmd 0xec)
[ 1685.230137] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 1685.230140] ata1.00: revalidation failed (errno=-5)
[ 1685.230144] ata1: limiting SATA link speed to 1.5 Gbps
[ 1685.760137] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1715.760126] ata1.00: qc timeout (cmd 0xec)
[ 1715.760137] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[ 1715.760139] ata1.00: revalidation failed (errno=-5)
[ 1715.760142] ata1.00: disabled
[ 1715.810216] ahci 0000:00:11.0: PCI INT A disabled
[ 1715.830154] PM: suspend of devices complete after 47679.847 msecs
[ 1715.830158] PM: suspend devices took 47.670 seconds
[ 1715.830159] ------------[ cut here ]------------
[ 1715.830166] WARNING: at /home/kernel-ppa/COD/linux/kernel/power/suspend_test.c:53 suspend_test_finish+0x89/0x90()
[ 1715.830168] Hardware name: R425/R525                  
[ 1715.830170] Component: suspend devices, time: 47670
[ 1715.830171] Modules linked in: binfmt_misc ppdev snd_hda_codec_atihdmi snd_hda_codec_realtek arc4 snd_hda_intel snd_hda_codec joydev snd_hwdep snd_pcm snd_seq_midi snd_rawmidi uvcvideo snd_seq_midi_event snd_seq videodev snd_timer v4l1_compat snd_seq_device v4l2_compat_ioctl32 pl2303 snd usbserial soundcore lp i2c_piix4 psmouse edac_core parport k10temp edac_mce_amd snd_page_alloc serio_raw sha256_generic cryptd aes_x86_64 aes_generic dm_crypt video output ahci libahci sky2 [last unloaded: led_class]
[ 1715.830199] Pid: 3251, comm: pm-suspend Not tainted 2.6.35-020635rc4-generic #020635rc4
[ 1715.830201] Call Trace:
[ 1715.830207]  [<ffffffff8109dc39>] ? suspend_test_finish+0x89/0x90
[ 1715.830211]  [<ffffffff81061390>] warn_slowpath_common+0x90/0xc0
[ 1715.830214]  [<ffffffff810614be>] warn_slowpath_fmt+0x6e/0x70
[ 1715.830218]  [<ffffffff813828ea>] ? dpm_suspend+0x15a/0x190
[ 1715.830221]  [<ffffffff8109dc39>] suspend_test_finish+0x89/0x90
[ 1715.830223]  [<ffffffff8109da11>] suspend_devices_and_enter+0xe1/0x100
[ 1715.830226]  [<ffffffff8109db11>] enter_state+0xe1/0xf0
[ 1715.830228]  [<ffffffff8109d064>] state_store+0xb4/0xf0
[ 1715.830232]  [<ffffffff812ac927>] kobj_attr_store+0x17/0x20
[ 1715.830237]  [<ffffffff811b91b2>] flush_write_buffer+0x62/0x90
[ 1715.830240]  [<ffffffff811b92f6>] sysfs_write_file+0x66/0xa0
[ 1715.830243]  [<ffffffff811511ac>] vfs_write+0xcc/0x1a0
[ 1715.830246]  [<ffffffff81151375>] sys_write+0x55/0x90
[ 1715.830250]  [<ffffffff8100b072>] system_call_fastpath+0x16/0x1b
[ 1715.830253] ---[ end trace 0295700764e4ce32 ]---
[ 1715.870199] PM: late suspend of devices complete after 39.939 msecs
[ 1715.870261] ACPI: Preparing to enter system sleep state S3
[ 1715.920383] PM: Saving platform NVS memory
[ 1715.920593] Disabling non-boot CPUs ...
[ 1715.960276] Broke affinity for irq 22
[ 1716.060123] CPU 1 is now offline
[ 1716.060127] SMP alternatives: switching to UP code
[ 1716.065073] Back to C!
[ 1716.065073] PM: Restoring platform NVS memory
[ 1716.065073] PCI-DMA: Resuming GART IOMMU
[ 1716.065073] PCI-DMA: Restoring GART aperture settings
[ 1716.065073] Enabling non-boot CPUs ...
[ 1716.065073] SMP alternatives: switching to SMP code
[ 1716.065073] Booting Node 0 Processor 1 APIC 0x1
[ 1716.260153] Switch to broadcast mode on CPU1
[ 1716.320392] CPU1 is up
[ 1716.320535] ACPI: Waking up from system sleep state S3
[ 1716.395258] pcieport 0000:00:02.0: restoring config space at offset 0x7 (was 0x20009191, writing 0x9191)
[ 1716.395264] pcieport 0000:00:02.0: restoring config space at offset 0x3 (was 0x10000, writing 0x10008)
[ 1716.395290] pcieport 0000:00:04.0: restoring config space at offset 0x7 (was 0x1f1, writing 0x200001f1)
[ 1716.395294] pcieport 0000:00:04.0: restoring config space at offset 0x3 (was 0x10000, writing 0x10008)
[ 1716.395319] pcieport 0000:00:05.0: restoring config space at offset 0x3 (was 0x10000, writing 0x10008)
[ 1716.395323] pcieport 0000:00:05.0: restoring config space at offset 0x1 (was 0x100400, writing 0x100407)
[ 1716.395347] pcieport 0000:00:06.0: restoring config space at offset 0x3 (was 0x10000, writing 0x10008)
[ 1716.412597] ehci_hcd 0000:00:12.2: BAR 0: set to [mem 0xf0409400-0xf04094ff] (PCI address [0xf0409400-0xf04094ff]
[ 1716.412630] ehci_hcd 0000:00:12.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00013)
[ 1716.432597] ehci_hcd 0000:00:13.2: BAR 0: set to [mem 0xf0409800-0xf04098ff] (PCI address [0xf0409800-0xf04098ff]
[ 1716.432630] ehci_hcd 0000:00:13.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00013)
[ 1716.432681] HDA Intel 0000:00:14.2: restoring config space at offset 0xf (was 0x10a, writing 0xa)
[ 1716.432701] HDA Intel 0000:00:14.2: restoring config space at offset 0x1 (was 0x4100006, writing 0x4100002)
[ 1716.432819] pci 0000:01:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 1716.432833] pci 0000:01:00.0: restoring config space at offset 0x3 (was 0x800000, writing 0x800008)
[ 1716.432860] HDA Intel 0000:01:00.1: restoring config space at offset 0xf (was 0x2ff, writing 0x20b)
[ 1716.432873] HDA Intel 0000:01:00.1: restoring config space at offset 0x4 (was 0x4, writing 0xcfedc004)
[ 1716.432877] HDA Intel 0000:01:00.1: restoring config space at offset 0x3 (was 0x800000, writing 0x800008)
[ 1716.432882] HDA Intel 0000:01:00.1: restoring config space at offset 0x1 (was 0x100000, writing 0x100003)
[ 1716.432913] pci 0000:02:00.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10a)
[ 1716.432928] pci 0000:02:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf0200004)
[ 1716.432932] pci 0000:02:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
[ 1716.432938] pci 0000:02:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100003)
[ 1716.433022] sky2 0000:04:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
[ 1716.433039] sky2 0000:04:00.0: restoring config space at offset 0x6 (was 0x1, writing 0xa001)
[ 1716.433045] sky2 0000:04:00.0: restoring config space at offset 0x4 (was 0x4, writing 0xf0300004)
[ 1716.433050] sky2 0000:04:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x8)
[ 1716.433056] sky2 0000:04:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100407)
[ 1716.433123] PM: early resume of devices complete after 37.905 msecs
[ 1716.433540] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 1716.433615] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1716.433634] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1716.433763] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1716.433789] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1716.433815] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1716.433830] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1716.433882] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1716.433897] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1716.433924] HDA Intel 0000:01:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1716.433931] HDA Intel 0000:01:00.1: setting latency timer to 64
[ 1716.434286] HDA Intel 0000:01:00.1: irq 45 for MSI/MSI-X
[ 1716.435304] sd 0:0:0:0: [sda] Starting disk
[ 1716.740101] usb 2-3: reset high speed USB device using ehci_hcd and address 2
[ 1716.780111] ata4: SATA link down (SStatus 0 SControl 300)
[ 1716.960086] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1717.062612] usb 3-1: reset full speed USB device using ohci_hcd and address 2
[ 1717.131055] ata2.00: configured for UDMA/100
[ 1717.243292] usb 3-1: device firmware changed
[ 1717.682615] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 1717.702648] sd 0:0:0:0: [sda] START_STOP FAILED
[ 1717.702652] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1717.702684] legacy_resume(): scsi_bus_resume+0x0/0x70 returns 262144
[ 1717.702692] PM: Device 0:0:0:0 failed to resume async: error 262144
[ 1717.702705] sd 0:0:0:0: [sda] Unhandled error code
[ 1717.702707] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1717.702710] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 1b 1c ed d0 00 00 a8 00
[ 1717.702716] end_request: I/O error, dev sda, sector 454880720
[ 1717.702749] PM: resume of devices complete after 1269.558 msecs
[ 1717.702824] Aborting journal on device dm-3-8.
[ 1717.702913] sd 0:0:0:0: [sda] Unhandled error code
[ 1717.702914] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1717.702917] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 1b 1c c1 88 00 00 08 00
[ 1717.702922] end_request: I/O error, dev sda, sector 454869384
[ 1717.702928] PM: resume devices took 1.270 seconds
[ 1717.702930] Buffer I/O error on device dm-3, logical block 21004288
[ 1717.702932] lost page write due to I/O error on dm-3
[ 1717.702940] JBD2: I/O error detected when updating journal superblock for dm-3-8.
[ 1717.703381] PM: Finishing wakeup.
[ 1717.703383] Restarting tasks ... 
[ 1717.703487] usb 3-1: USB disconnect, address 2
[ 1717.703620] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[ 1717.703634] pl2303 3-1:1.0: device disconnected
[ 1717.704683] EXT4-fs error (device dm-3): ext4_journal_start_sb: Detected aborted journal
[ 1717.704839] EXT4-fs (dm-3): Remounting filesystem read-only
[ 1717.710163] done.
[ 1717.710169] video LNXVIDEO:00: Restoring backlight state
[ 1717.880078] usb 3-1: new full speed USB device using ohci_hcd and address 3
[ 1718.013678] sky2 0000:04:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx
[ 1718.083270] pl2303 3-1:1.0: pl2303 converter detected
[ 1718.105296] usb 3-1: pl2303 converter now attached to ttyUSB0
[ 1718.658965] sd 0:0:0:0: [sda] Unhandled error code
[ 1718.658969] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1718.658973] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 0e 93 a7 f0 00 00 18 00
[ 1718.658981] end_request: I/O error, dev sda, sector 244557808
[ 1718.659093] sd 0:0:0:0: [sda] Unhandled error code
[ 1718.659095] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1718.659098] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 0e 93 a7 f0 00 00 08 00
[ 1718.659104] end_request: I/O error, dev sda, sector 244557808
[ 1719.355255] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.355260] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.355264] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 0e ba dd 88 00 00 20 00
[ 1719.355271] end_request: I/O error, dev sda, sector 247127432
[ 1719.355383] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.355385] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.355388] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 0e ba dd 88 00 00 08 00
[ 1719.355394] end_request: I/O error, dev sda, sector 247127432
[ 1719.423422] cfg80211: Calling CRDA to update world regulatory domain
[ 1719.426916] cfg80211: World regulatory domain updated:
[ 1719.426920]     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 1719.426923]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1719.426926]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 1719.426928]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 1719.426930]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1719.426933]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 1719.479185] ath9k 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1719.479197] ath9k 0000:02:00.0: setting latency timer to 64
[ 1719.528947] ath: EEPROM regdomain: 0x65
[ 1719.528949] ath: EEPROM indicates we should expect a direct regpair map
[ 1719.528954] ath: Country alpha2 being used: 00
[ 1719.528956] ath: Regpair used: 0x65
[ 1719.539692] phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 1719.541318] Registered led device: ath9k-phy0::radio
[ 1719.541603] Registered led device: ath9k-phy0::assoc
[ 1719.541767] Registered led device: ath9k-phy0::tx
[ 1719.541904] Registered led device: ath9k-phy0::rx
[ 1719.541912] phy0: Atheros AR9285 Rev:2 mem=0xffffc90001600000, irq=16
[ 1719.570081] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.570086] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.570090] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 17 cb 98 00 00 08 00
[ 1719.570098] end_request: I/O error, dev sda, sector 253217688
[ 1719.570151] Buffer I/O error on device dm-1, logical block 1656130
[ 1719.570192] lost page write due to I/O error on dm-1
[ 1719.570416] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.570421] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.570425] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 4c 25 a8 00 00 08 00
[ 1719.570432] end_request: I/O error, dev sda, sector 256648616
[ 1719.570518] Buffer I/O error on device dm-1, logical block 2084996
[ 1719.570560] lost page write due to I/O error on dm-1
[ 1719.570572] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.570573] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.570576] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0e 82 f4 10 00 00 08 00
[ 1719.570582] end_request: I/O error, dev sda, sector 243463184
[ 1719.570625] Buffer I/O error on device dm-1, logical block 436817
[ 1719.570667] lost page write due to I/O error on dm-1
[ 1719.571509] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.571511] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.571514] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 49 a5 18 00 00 08 00
[ 1719.571521] end_request: I/O error, dev sda, sector 256484632
[ 1719.571604] Buffer I/O error on device dm-1, logical block 2064498
[ 1719.571646] lost page write due to I/O error on dm-1
[ 1719.571658] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.571659] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.571662] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 4a 70 78 00 00 08 00
[ 1719.571668] end_request: I/O error, dev sda, sector 256536696
[ 1719.571713] Buffer I/O error on device dm-1, logical block 2071006
[ 1719.571755] lost page write due to I/O error on dm-1
[ 1719.571760] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.571762] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.571764] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 61 cc f0 00 00 08 00
[ 1719.571770] end_request: I/O error, dev sda, sector 258067696
[ 1719.571815] Buffer I/O error on device dm-1, logical block 2262381
[ 1719.571856] lost page write due to I/O error on dm-1
[ 1719.571864] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.571866] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.571868] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0e 57 0a f0 00 00 08 00
[ 1719.571874] end_request: I/O error, dev sda, sector 240585456
[ 1719.571918] Buffer I/O error on device dm-1, logical block 77101
[ 1719.571960] lost page write due to I/O error on dm-1
[ 1719.571964] JBD2: Detected IO errors while flushing file data on dm-1-8
[ 1719.580169] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.580174] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.580178] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 51 e7 88 00 00 b0 00
[ 1719.580186] end_request: I/O error, dev sda, sector 257025928
[ 1719.580798] Aborting journal on device dm-1-8.
[ 1719.580912] EXT4-fs error (device dm-1) in ext4_reserve_inode_write: Journal has aborted
[ 1719.580959] EXT4-fs (dm-1): Remounting filesystem read-only
[ 1719.581004] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.581007] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.581010] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0f 51 a1 88 00 00 08 00
[ 1719.581016] end_request: I/O error, dev sda, sector 257008008
[ 1719.581026] Buffer I/O error on device dm-1, logical block 2129920
[ 1719.581027] lost page write due to I/O error on dm-1
[ 1719.581149] 
[ 1719.581214] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.581217] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.581220] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 0e 4d a1 88 00 00 08 00
[ 1719.581227] end_request: I/O error, dev sda, sector 239968648
[ 1719.581254] JBD2: I/O error detected when updating journal superblock for dm-1-8.
[ 1719.581268] journal commit I/O error
[ 1719.581391] Buffer I/O error on device dm-1, logical block 0
[ 1719.581433] lost page write due to I/O error on dm-1
[ 1719.647005] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1719.682598] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.682603] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.682607] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 0e b9 63 a8 00 00 40 00
[ 1719.682615] end_request: I/O error, dev sda, sector 247030696
[ 1719.682786] sd 0:0:0:0: [sda] Unhandled error code
[ 1719.682788] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 1719.682791] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 0e b9 63 b8 00 00 08 00
[ 1719.682797] end_request: I/O error, dev sda, sector 247030712

[-- Attachment #3: lspci-vv --]
[-- Type: text/plain, Size: 28041 bytes --]

00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge Alternate
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: [c4] HyperTransport: Slave or Primary Interface
		Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL-
		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
		Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
		Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
		Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
		Revision ID: 3.00
		Link Frequency 0: 1.6GHz
		Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
		Link Frequency 1: 200MHz
		Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
		Prefetchable memory behind bridge Upper: 00-00
		Bus Number: 00
	Capabilities: [54] HyperTransport: UnitID Clumping
	Capabilities: [40] HyperTransport: Retry Mode
	Capabilities: [9c] HyperTransport: #1a
	Capabilities: [f8] HyperTransport: #1c

00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: cfe00000-cfefffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep+ BwNot+
		LnkCtl:	ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
			Slot #  2, PowerLimit 75.000000; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet+ LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
		Address: fee0300c  Data: 4151
	Capabilities: [b0] Subsystem: Samsung Electronics Co Ltd Device c553
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information <?>
	Capabilities: [110] Virtual Channel <?>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Memory behind bridge: f0200000-f02fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep+ BwNot+
		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
			Slot #  4, PowerLimit 25.000000; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet+ LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
		Address: fee0300c  Data: 4159
	Capabilities: [b0] Subsystem: Samsung Electronics Co Ltd Device c553
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information <?>
	Capabilities: [110] Virtual Channel <?>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: c8000000-c81fffff
	Prefetchable memory behind bridge: 00000000c8200000-00000000c83fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #247, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep+ BwNot+
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed unknown, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
			Slot #  5, PowerLimit 25.000000; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
			Changed: MRL- PresDet- LinkState-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
		Address: fee0300c  Data: 4161
	Capabilities: [b0] Subsystem: Samsung Electronics Co Ltd Device c553
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information <?>
	Capabilities: [110] Virtual Channel <?>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: f0300000-f03fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #3, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep+ BwNot+
		LnkCtl:	ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
			Slot #  6, PowerLimit 25.000000; Interlock- NoCompl+
		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
			Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
		SltSta:	Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
			Changed: MRL- PresDet+ LinkState+
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
		Address: fee0300c  Data: 4169
	Capabilities: [b0] Subsystem: Samsung Electronics Co Ltd Device c553
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100] Vendor Specific Information <?>
	Capabilities: [110] Virtual Channel <?>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] (prog-if 01)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 22
	Region 0: I/O ports at 8420 [size=8]
	Region 1: I/O ports at 8414 [size=4]
	Region 2: I/O ports at 8418 [size=8]
	Region 3: I/O ports at 8410 [size=4]
	Region 4: I/O ports at 8400 [size=16]
	Region 5: Memory at f0409000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [70] SATA HBA <?>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f0404000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f0405000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at f0409400 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd

00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller (prog-if 10)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at f0406000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller (prog-if 10)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at f0407000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller (prog-if 20)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 19
	Region 0: Memory at f0409800 (32-bit, non-prefetchable) [size=256]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Capabilities: [e4] Debug port: BAR=1 offset=00e0
	Kernel driver in use: ehci_hcd

00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3c)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
	Kernel modules: i2c-piix4

00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin ? routed to IRQ 16
	Region 0: Memory at f0400000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (prog-if 01)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller (prog-if 10)
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at f0408000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
		Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
		Revision ID: 3.00
		Link Frequency: 1.6GHz
		Link Error: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
		Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-

00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel modules: amd64_edac_mod

00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [f0] Secure device <?>
	Kernel driver in use: k10temp
	Kernel modules: k10temp

00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series]
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
	Region 2: Memory at cfee0000 (64-bit, non-prefetchable) [size=128K]
	Region 4: I/O ports at 9000 [size=256]
	[virtual] Expansion ROM at cfe00000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [100] Vendor Specific Information <?>
	Kernel modules: radeon

01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series]
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin B routed to IRQ 45
	Region 0: Memory at cfedc000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
			ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Suprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
		Address: 00000000fee0300c  Data: 4189
	Capabilities: [100] Vendor Specific Information <?>
	Kernel driver in use: HDA Intel
	Kernel modules: snd-hda-intel

02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
	Subsystem: Foxconn International, Inc. Device e025
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at f0200000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
		Address: 00000000  Data: 0000
	Capabilities: [60] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
			ClockPM- Suprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100] Advanced Error Reporting <?>
	Capabilities: [140] Virtual Channel <?>
	Capabilities: [160] Device Serial Number 12-14-24-ff-ff-17-15-00
	Capabilities: [170] Power Budgeting <?>
	Kernel driver in use: ath9k
	Kernel modules: ath9k

04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller
	Subsystem: Samsung Electronics Co Ltd Device c553
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 44
	Region 0: Memory at f0300000 (64-bit, non-prefetchable) [size=16K]
	Region 2: I/O ports at a000 [size=256]
	Capabilities: [48] Power Management version 3
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
		Address: 00000000fee0300c  Data: 4179
	Capabilities: [c0] Express (v2) Legacy Endpoint, MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 512 bytes
		DevSta:	CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 unlimited
			ClockPM+ Suprise- LLActRep- BwNot-
		LnkCtl:	ASPM L0s L1 Enabled; RCB 128 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [100] Advanced Error Reporting <?>
	Capabilities: [130] Device Serial Number 00-24-54-ff-ff-6e-90-bf
	Kernel driver in use: sky2
	Kernel modules: sky2


[-- Attachment #4: smartctl-a --]
[-- Type: text/plain, Size: 5102 bytes --]

smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     SAMSUNG HM321HI
Serial Number:    S26VJ9FZ400577
Firmware Version: 2AJ10001
User Capacity:    320.072.933.376 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  Not recognized. Minor revision code: 0x28
Local Time is:    Fri Jul  9 17:48:10 2010 CEST

==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.

SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 (4800) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  80) minutes.
SCT capabilities: 	       (0x003f)	SCT Status supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   100   100   051    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0026   252   252   000    Old_age   Always       -       0
  3 Spin_Up_Time            0x0023   094   071   025    Pre-fail  Always       -       2118
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       147
  5 Reallocated_Sector_Ct   0x0033   252   252   010    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   252   252   051    Old_age   Always       -       0
  8 Seek_Time_Performance   0x0024   252   252   015    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       183
 10 Spin_Retry_Count        0x0032   252   252   051    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   100   000    Old_age   Always       -       12
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       148
191 G-Sense_Error_Rate      0x0022   100   100   000    Old_age   Always       -       333
192 Power-Off_Retract_Count 0x0022   252   252   000    Old_age   Always       -       0
194 Temperature_Celsius     0x0002   064   058   000    Old_age   Always       -       36 (Lifetime Min/Max 17/45)
195 Hardware_ECC_Recovered  0x003a   100   100   000    Old_age   Always       -       0
196 Reallocated_Event_Count 0x0032   252   252   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   252   252   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   252   252   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0036   100   100   000    Old_age   Always       -       3
200 Multi_Zone_Error_Rate   0x002a   100   100   000    Old_age   Always       -       8
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       12
225 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       3995

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%       180         -

SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Completed [00% left] (0-65535)
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


^ permalink raw reply	[flat|nested] 78+ messages in thread
* Re: [PATCH] SATA / AHCI: Do not play with the link PM during suspend to RAM
@ 2010-08-28 20:28 Siddhartha Jain
  2010-08-30 12:55 ` Tejun Heo
  0 siblings, 1 reply; 78+ messages in thread
From: Siddhartha Jain @ 2010-08-28 20:28 UTC (permalink / raw)
  To: linux-ide

Hi,

I have the same symptom as Stephan and came across this thread while
googling for more info.

Hardware: Macbook Pro 5,4 (Firmware version 1.7)

OS: Fedora 13 x64 
Kernel: 2.6.33.8-149.fc13.x86_64 (stock fedora kernel)
Modifications: Video is on Nvidia proprietary driver and Root and swap
are encrypted with luks. Kernel boot parameters are:

kernel /vmlinuz-2.6.33.8-149.fc13.x86_64 ro
root=/dev/mapper/luks-f01b2a77-921b-45c1-8f28-6095ab3a56f1
rd_LUKS_UUID=luks-f01b2a77-921b-45c1-8f28-6095ab3a56f1
rd_LUKS_UUID=luks-91e5037b-267c-4572-
9c99-baaa5ca41600 rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8
SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb rdblacklist=nouveau vga=792
resume=UUID=91e5037b-267c-4572-9c99-baaa5ca41600 

The system seems to go to suspend alright but on resume, the hdd does
not seem to wake-up. After resume, in X, the login screen background
shows up but the login prompt box does not. If I am logged in before
suspend then after resume, every command I run including reboot/shutdown
etc returns Input/Output error. After resume, if I try to ssh in, I get
the ssh prompt but authentication does not succeed and I get password
failures. 

Bit more HW/SW info:

1. From lspci -vv
00:0b.0 IDE interface: nVidia Corporation MCP79 SATA Controller (rev b1)
(prog-if 85 [Master SecO PriO])
	Subsystem: nVidia Corporation Device cb79
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 27
	Region 0: I/O ports at 21d8 [size=8]
	Region 1: I/O ports at 21ec [size=4]
	Region 2: I/O ports at 21d0 [size=8]
	Region 3: I/O ports at 21e8 [size=4]
	Region 4: I/O ports at 21c0 [size=16]
	Region 5: Memory at d3584000 (32-bit, non-prefetchable) [size=8K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [8c] SATA HBA v1.0 InCfgSpace
	Capabilities: [b0] MSI: Enable+ Count=1/8 Maskable- 64bit+
		Address: 00000000fee0200c  Data: 4181
	Kernel driver in use: ahci
	Kernel modules: ata_generic, pata_acpi


2. HDD Info from smartctl
# smartctl -a /dev/sda
smartctl 5.39.1 2010-01-28 r3054 [x86_64-redhat-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen,
http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model:     FUJITSU MJA2250BH FFS G1
Serial Number:    K94DTA22N7C1
Firmware Version: 00810020
User Capacity:    250,059,350,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 3f
Local Time is:    Sat Aug 28 13:09:06 2010 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled


3. ATA related messages from bootup (dmesg | grep ATA)
ata1: SATA max UDMA/133 irq_stat 0x00400000, PHY RDY changed irq 27
ata2: SATA max UDMA/133 irq_stat 0x00400000, PHY RDY changed irq 27
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: FUJITSU MJA2250BH FFS G1, 00810020, max UDMA/100
ata2.00: ATAPI: HL-DT-ST DVDRW  GS23N, SB03, max UDMA/133
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MJA2250B 0081 PQ: 0
ANSI: 5
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)


4. # cat /sys/class/scsi_host/host0/link_power_management_policy 
max_performance


5. Some odd errors at boot-up related to 'ata' (captured by directing
*.* to a log file in rsyslog)
Aug 28 11:49:39 myfedorahat kernel: ACPI: SSDT 00000000bfee4000 000A5
(v01 SataRe  SataPri 00001000 INTL 20061109)
Aug 28 11:49:39 myfedorahat kernel: ACPI: SSDT 00000000bfee3000 0009F
(v01 SataRe  SataSec 00001000 INTL 20061109)
Aug 28 11:49:39 myfedorahat kernel:  #0 [0000000000 - 0000001000]   BIOS
data page ==> [0000000000 - 0000001000]
Aug 28 11:49:39 myfedorahat kernel: Kernel command line: ro
root=/dev/mapper/luks-f01b2a77-921b-45c1-8f28-6095ab3a56f1
rd_LUKS_UUID=luks-f01b2a77-921b-45c1-8f28-6095ab3a56f1
rd_LUKS_UUID=luks-91e5037b-26
7c-4572-9c99-baaa5ca41600 rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8
SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb rdblacklist=nouveau vga=792
resume=UUID=91e5037b-267c-4572-9c99-baaa5ca41600 
Aug 28 11:49:39 myfedorahat kernel: Memory: 3758324k/5242880k available
(4289k kernel code, 1336536k absent, 148020k reserved, 7539k data, 756k
init)
Aug 28 11:49:39 myfedorahat kernel: ACPI: EC: GPE = 0x3f, I/O:
command/status = 0x66, data = 0x62
Aug 28 11:49:39 myfedorahat kernel: libata version 3.00 loaded.
Aug 28 11:49:39 myfedorahat kernel: ata1: SATA max UDMA/133 irq_stat
0x00400000, PHY RDY changed irq 27
Aug 28 11:49:39 myfedorahat kernel: ata2: SATA max UDMA/133 irq_stat
0x00400000, PHY RDY changed irq 27
Aug 28 11:49:39 myfedorahat kernel: ata3: DUMMY
Aug 28 11:49:39 myfedorahat kernel: ata4: DUMMY
Aug 28 11:49:39 myfedorahat kernel: ata5: DUMMY
Aug 28 11:49:39 myfedorahat kernel: ata6: DUMMY
Aug 28 11:49:39 myfedorahat kernel: ata1: SATA link up 1.5 Gbps (SStatus
113 SControl 300)
Aug 28 11:49:39 myfedorahat kernel: ata2: SATA link up 1.5 Gbps (SStatus
113 SControl 300)
Aug 28 11:49:39 myfedorahat kernel: ata1.00: ATA-8: FUJITSU MJA2250BH
FFS G1, 00810020, max UDMA/100
Aug 28 11:49:39 myfedorahat kernel: ata1.00: 488397168 sectors, multi
16: LBA48 NCQ (depth 31/32)
Aug 28 11:49:39 myfedorahat kernel: ata1.00: configured for UDMA/100
Aug 28 11:49:39 myfedorahat kernel: ata1: exception Emask 0x10 SAct 0x0
SErr 0x5850000 action 0xe frozen
Aug 28 11:49:39 myfedorahat kernel: ata1: irq_stat 0x00000040,
connection status changed
Aug 28 11:49:39 myfedorahat kernel: ata1: SError: { PHYRdyChg CommWake
LinkSeq TrStaTrns DevExch }
Aug 28 11:49:39 myfedorahat kernel: ata2.00: ATAPI: HL-DT-ST DVDRW
GS23N, SB03, max UDMA/133
Aug 28 11:49:39 myfedorahat kernel: ata1: hard resetting link
Aug 28 11:49:39 myfedorahat kernel: ata2.00: configured for UDMA/133
Aug 28 11:49:39 myfedorahat kernel: ata2: exception Emask 0x10 SAct 0x0
SErr 0x5950000 action 0xe frozen
Aug 28 11:49:39 myfedorahat kernel: ata2: irq_stat 0x00400040,
connection status changed
Aug 28 11:49:39 myfedorahat kernel: ata2: SError: { PHYRdyChg CommWake
Dispar LinkSeq TrStaTrns DevExch }
Aug 28 11:49:39 myfedorahat kernel: ata2: hard resetting link
Aug 28 11:49:39 myfedorahat kernel: ata1: SATA link up 1.5 Gbps (SStatus
113 SControl 300)
Aug 28 11:49:39 myfedorahat kernel: ata1.00: configured for UDMA/100
Aug 28 11:49:39 myfedorahat kernel: ata1: EH complete
Aug 28 11:49:39 myfedorahat kernel: ata2: SATA link up 1.5 Gbps (SStatus
113 SControl 300)
Aug 28 11:49:39 myfedorahat kernel: ata2.00: configured for UDMA/133
Aug 28 11:49:39 myfedorahat kernel: ata2: EH complete
Aug 28 11:49:39 myfedorahat kernel: Write protecting the kernel
read-only data: 10240k
Aug 28 11:49:39 myfedorahat kernel: EXT4-fs (dm-0): mounted filesystem
with ordered data mode
Aug 28 11:49:39 myfedorahat kernel: EXT4-fs (sda1): mounted filesystem
with ordered data mode


I am going to try pointing rsyslog at a remote syslog server to see if I
can capture what happens at resume-time but any other pointers to
debug/troubleshoot this issue will be helpful. I tried booting with
"pci=nomsi" but that makes the box hang at boot-up. Tried disabling acpi
and switched to APM but that seems risky because after suspend, APM does
not seem to have control over CPU and fans. With APM enabled, I did a
suspend and put the macbook in my bag. Four hours later when I pulled it
out of the bag, the fan was spinning at highest RPM and the macbook was
running really hot. With ACPI, at least, all the damage is only to
filesystem when I have to force reboot on resume :)

Thanks,

- Siddhartha


^ permalink raw reply	[flat|nested] 78+ messages in thread

end of thread, other threads:[~2010-10-29  5:49 UTC | newest]

Thread overview: 78+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-07-09 15:50 HDD not suspending properly / dead on resume Stephan Diestelhorst
2010-07-09 15:50 ` Stephan Diestelhorst
2010-07-09 21:47 ` Stephan Diestelhorst
2010-07-09 21:53   ` Rafael J. Wysocki
2010-07-09 23:04     ` Stephan Diestelhorst
2010-07-10  0:06       ` Rafael J. Wysocki
2010-07-10  6:50         ` Stephan Diestelhorst
2010-07-10 10:03           ` Tejun Heo
2010-07-10 13:45             ` Rafael J. Wysocki
2010-07-28 21:50             ` [PATCH] SATA / AHCI: Do not play with the link PM during suspend to RAM (was: Re: HDD not suspending properly / dead on resume) Rafael J. Wysocki
2010-07-30 14:18               ` [PATCH] SATA / AHCI: Do not play with the link PM during suspend to RAM Tejun Heo
2010-08-05 16:08                 ` Tejun Heo
2010-08-05 19:58                   ` Rafael J. Wysocki
2010-08-06  6:30                   ` Stephan Diestelhorst
2010-08-06  7:06                     ` Tejun Heo
2010-08-06  9:04                       ` Stephan Diestelhorst
2010-08-17  7:51                   ` Stephan Diestelhorst
2010-08-17  8:08                     ` Tejun Heo
2010-08-17  9:32                       ` Stephan Diestelhorst
2010-08-17 10:15                         ` Tejun Heo
2010-08-17 10:29                           ` Stephan Diestelhorst
2010-08-17 10:51                             ` Stephan Diestelhorst
2010-08-17 15:04                               ` Tejun Heo
2010-08-17 21:28                                 ` Stephan Diestelhorst
2010-08-18  6:12                                   ` Tejun Heo
2010-08-19 16:23                                     ` Stephan Diestelhorst
2010-08-23 12:03                                       ` Tejun Heo
2010-08-23 18:58                                         ` Rafael J. Wysocki
2010-08-24  7:37                                           ` Tejun Heo
2010-08-24 20:39                                             ` Rafael J. Wysocki
2010-08-26 23:09                                               ` Rafael J. Wysocki
2010-08-26 23:46                                                 ` Rafael J. Wysocki
2010-09-02  9:06                                                 ` Tejun Heo
2010-09-02 10:02                                                   ` [PATCH] libata: skip EH autopsy and recovery during suspend Tejun Heo
2010-09-02 14:33                                                     ` Stephan Diestelhorst
2010-09-02 14:33                                                       ` Stephan Diestelhorst
2010-09-02 20:11                                                       ` Rafael J. Wysocki
2010-09-02 20:52                                                       ` Stephan Diestelhorst
2010-09-07 11:54                                                         ` Stephan Diestelhorst
2010-09-02 20:16                                                     ` Rafael J. Wysocki
2010-09-02 20:25                                                       ` Tejun Heo
2010-09-02 20:28                                                         ` Rafael J. Wysocki
2010-09-02 20:33                                                           ` Tejun Heo
2010-09-02 21:01                                                             ` [linux-pm] " Alan Stern
2010-09-02 21:09                                                               ` Rafael J. Wysocki
2010-09-02 21:09                                                                 ` [linux-pm] " Rafael J. Wysocki
2010-09-03  8:55                                                               ` Tejun Heo
2010-09-03 14:16                                                                 ` Alan Stern
2010-09-07 12:05                                                   ` [PATCH #upstream-fixes] " Tejun Heo
2010-08-24 16:07                                         ` [PATCH] SATA / AHCI: Do not play with the link PM during suspend to RAM Stephan Diestelhorst
2010-08-24 16:11                                           ` Stephan Diestelhorst
2010-08-26 16:15                                             ` Stephan Diestelhorst
2010-08-26 18:24                                               ` Rafael J. Wysocki
2010-08-27 23:35                                                 ` Rafael J. Wysocki
2010-09-02 14:31                                                   ` Stephan Diestelhorst
2010-09-02 14:31                                                     ` Stephan Diestelhorst
2010-08-17 11:19                           ` Rafael J. Wysocki
2010-08-17 11:29                             ` Tejun Heo
2010-08-17 12:10                               ` Stephan Diestelhorst
2010-08-17 12:09                                 ` Tejun Heo
2010-08-02 20:48               ` [PATCH] SATA / AHCI: Do not play with the link PM during suspend to RAM (was: Re: HDD not suspending properly / dead on resume) Stephan Diestelhorst
2010-08-02 21:38                 ` Rafael J. Wysocki
2010-08-03  8:36                   ` Stephan Diestelhorst
2010-08-03 21:13                     ` Rafael J. Wysocki
2010-07-10 13:08           ` HDD not suspending properly / dead on resume Rafael J. Wysocki
2010-07-12 15:35 ` Maciej Rutecki
2010-08-28 20:28 [PATCH] SATA / AHCI: Do not play with the link PM during suspend to RAM Siddhartha Jain
2010-08-30 12:55 ` Tejun Heo
2010-08-30 15:25   ` Siddhartha Jain
2010-08-30 22:26     ` Siddhartha Jain
2010-08-31  0:59       ` Siddhartha Jain
2010-08-31  2:03         ` Siddhartha Jain
2010-09-01 19:47           ` Siddhartha Jain
2010-09-02 10:09             ` Tejun Heo
2010-09-02 19:56               ` Siddhartha Jain
2010-09-03  9:04                 ` Tejun Heo
2010-10-28  2:11                   ` Siddhartha Jain
2010-10-29  5:49                     ` Jeff Garzik

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.