From mboxrd@z Thu Jan  1 00:00:00 1970
From: Marek Vasut <marek.vasut@gmail.com>
Date: Wed, 24 Aug 2011 18:26:03 +0200
Subject: [U-Boot] [PATCH v2 3/3] Armada100: Enable 88E3015 PHY support
	for GplugD
In-Reply-To: <1314191240-30938-3-git-send-email-ajay.bhargav@einfochips.com>
References: <n> <1314191240-30938-3-git-send-email-ajay.bhargav@einfochips.com>
Message-ID: <201108241826.03756.marek.vasut@gmail.com>
List-Id: <u-boot.lists.denx.de>
MIME-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
To: u-boot@lists.denx.de

On Wednesday, August 24, 2011 03:07:20 PM Ajay Bhargav wrote:
> This patch adds support for 88E3015 PHY for Marvell GplugD board.
> This patch depends on series of patch which adds support for Marvell
> GuruPlug-Display.
> 
> Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
> ---
> Changes for v2:
> 	- Not changed
> 
>  board/Marvell/gplugd/gplugd.c |   33 ++++++++++++++++++++++++++++++++-
>  include/configs/gplugd.h      |   14 ++++++++++++++
>  2 files changed, 46 insertions(+), 1 deletions(-)
> 
> diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
> index 4cd4086..bf3cdb4 100644
> --- a/board/Marvell/gplugd/gplugd.c
> +++ b/board/Marvell/gplugd/gplugd.c
> @@ -32,6 +32,8 @@
>  #include <mvmfp.h>
>  #include <asm/arch/mfp.h>
>  #include <asm/arch/armada100.h>
> +#include <asm/gpio.h>
> +#include <miiphy.h>
> 
>  #ifdef CONFIG_ARMADA100_FEC
>  #include <net.h>
> @@ -83,6 +85,11 @@ int board_init(void)
>  	gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
>  	/* adress of boot parameters */
>  	gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
> +	/* Assert PHY_RST# */
> +	gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW);
> +	udelay(10);
> +	/* Deassert PHY_RST# */
> +	gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH);
>  	return 0;
>  }
> 
> @@ -97,5 +104,29 @@ int board_eth_init(bd_t *bis)
> 
>  	return armada100_fec_register();
>  }
> -#endif /* CONFIG_ARMADA100_FEC */
> +#ifdef CONFIG_RESET_PHY_R
> +/* Configure and initialize PHY chip 88E3015 */
> +void reset_phy(void)
> +{
> +	u16 phy_adr;
> +	const char *name = "armd-fec0";
> +
> +	if (miiphy_set_current_dev(name))
> +		return;
> +
> +	/* command to read PHY dev address */
> +	if (miiphy_read(name, 0xff, 0xff, (u16 *) &phy_adr)) {

Do you need the cast there ?

> +		printf("Err..%s could not read PHY dev address\n", __func__);
> +		return;
> +	}
> 
> +	/* Set Ethernet LED in TX blink mode */
> +	miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
> +	miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
> +
> +	/* reset the phy */
> +	miiphy_reset(name, phy_adr);
> +	printf("88E3015 Initialized on %s\n", name);

Maybe debug() ?

> +}
> +#endif /* CONFIG_RESET_PHY_R */
> +#endif /* CONFIG_ARMADA100_FEC */
> diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
> index f3b94d8..b63ffd5 100644
> --- a/include/configs/gplugd.h
> +++ b/include/configs/gplugd.h
> @@ -80,6 +80,20 @@
>  #define CONFIG_ROOTPATH				"/tftpboot"
>  #define CONFIG_SYS_IMG_NAME			"uImage"
> 
> +/* GPIO Support */
> +#define CONFIG_MARVELL_GPIO
> +
> +/* PHY configuration */
> +#define CONFIG_MII
> +#define CONFIG_CMD_MII
> +#define CONFIG_RESET_PHY_R
> +/* 88E3015 register definition */
> +#define PHY_LED_PAR_SEL_REG		22
> +#define PHY_LED_MAN_REG			25
> +#define PHY_LED_VAL			0x5b	/* LINK LED1, ACT LED2 */
> +/* GPIO Configuration for PHY */
> +#define CONFIG_SYS_GPIO_PHY_RST		104	/* GPIO104 */
> +
>  /*
>   * mv-common.h should be defined after CMD configs since it used them
>   * to enable certain macros

Cheers