From mboxrd@z Thu Jan 1 00:00:00 1970 Return-path: Received: from mail-ey0-f174.google.com ([209.85.215.174]:54501 "EHLO mail-ey0-f174.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752649Ab2DWHuU (ORCPT ); Mon, 23 Apr 2012 03:50:20 -0400 Received: by eaaq12 with SMTP id q12so3108120eaa.19 for ; Mon, 23 Apr 2012 00:50:18 -0700 (PDT) Date: Mon, 23 Apr 2012 09:50:01 +0200 From: Anisse Astier To: Gertjan van Wingerde Cc: "linux-wireless@vger.kernel.org" , "users@rt2x00.serialmonkey.com" , Julian Calaby , "linville@tuxdriver.com" , RA-ShiangTu , Ivo van Doorn , Helmut Schaa , Kevin Chou , John Li , RA-Jay Hung Subject: Re: [PATCH] rt2800: add chipset revision RT5390R support Message-ID: <20120423095001.50af46cf@destiny.ordissimo> (sfid-20120423_095039_698777_661799EF) In-Reply-To: References: <1334759039-24349-1-git-send-email-anisse@astier.eu> Mime-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Sender: linux-wireless-owner@vger.kernel.org List-ID: On Fri, 20 Apr 2012 19:07:38 +0200, Gertjan van Wingerde wrote : > Hi Anisse, > > > On 18 apr. 2012, at 16:23, Anisse Astier wrote: > > > About 70% of the chips with revision RT5390R initialize incorrectly, using > > the auxiliary antenna instead of the main one. The net result is that > > signal reception is very poor (no AP further than 1M). > > > > This chipset differs from RT5390 and RT5390F by its support of hardware > > antenna diversity. Therefore antenna selection should be done > > differently, by disabling software features and previously selected > > antenna. > > > > This changeset does just that, and makes all RT5390R work properly. > > > > This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO > > driver. > > > > Signed-off-by: Anisse Astier > > --- > > drivers/net/wireless/rt2x00/rt2800.h | 1 + > > drivers/net/wireless/rt2x00/rt2800lib.c | 10 ++++++++++ > > 2 files changed, 11 insertions(+) > > > > diff --git a/drivers/net/wireless/rt2x00/rt2800.h b/drivers/net/wireless/rt2x00/rt2800.h > > index 063bfa8..1ce2634 100644 > > --- a/drivers/net/wireless/rt2x00/rt2800.h > > +++ b/drivers/net/wireless/rt2x00/rt2800.h > > @@ -83,6 +83,7 @@ > > #define REV_RT3090E 0x0211 > > #define REV_RT3390E 0x0211 > > #define REV_RT5390F 0x0502 > > +#define REV_RT5390R 0x1502 > > > > /* > > * Signal information. > > diff --git a/drivers/net/wireless/rt2x00/rt2800lib.c b/drivers/net/wireless/rt2x00/rt2800lib.c > > index bd19802..6c95101 100644 > > --- a/drivers/net/wireless/rt2x00/rt2800lib.c > > +++ b/drivers/net/wireless/rt2x00/rt2800lib.c > > @@ -3356,6 +3356,16 @@ static int rt2800_init_bbp(struct rt2x00_dev *rt2x00dev) > > rt2800_register_write(rt2x00dev, GPIO_CTRL_CFG, reg); > > } > > > > + /* This chip has hardware antenna diversity*/ > > + if (rt2x00_rt_rev_gte(rt2x00dev, RT5390, REV_RT5390R)) { > > + rt2x00dev->default_ant.tx = ANTENNA_HW_DIVERSITY; /* Unused */ > > + rt2x00dev->default_ant.rx = ANTENNA_HW_DIVERSITY; /* Unused */ > > + > > + rt2800_bbp_write(rt2x00dev, 150, 0); /* Disable Antenna Software OFDM */ > > + rt2800_bbp_write(rt2x00dev, 151, 0); /* Disable Antenna Software CCK */ > > + rt2800_bbp_write(rt2x00dev, 154, 0); /* Clear previously selected antenna */ > > + } > > + > > rt2800_bbp_read(rt2x00dev, 152, &value); > > if (ant == 0) > > rt2x00_set_field8(&value, BBP152_RX_DEFAULT_ANT, 1); > > Thanks for figuring this out. However, I think the default_ant initializations should be put at the place where the other initializations for the same field are (I believe that is somewhere in the rt2800_init_eeprom function (or a function with a similar name). I'm not even sure those are needed. I put them there in case someone would want to use them in the future. What do you think ? > The BBP CSR writes are in the right place. > > --- > Gertjan -- Anisse