From mboxrd@z Thu Jan 1 00:00:00 1970 From: Tony Lindgren Subject: Re: [PATCH 2/6] ARM: OMAP2+: Remove board-omap4panda.c Date: Wed, 12 Jun 2013 10:14:08 -0700 Message-ID: <20130612171407.GM8164@atomide.com> References: <20130517191304.468.73487.stgit@localhost> <20130517191753.468.1734.stgit@localhost> <20130612163124.GD8164@atomide.com> Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Return-path: Received: from mho-03-ewr.mailhop.org ([204.13.248.66]:45442 "EHLO mho-01-ewr.mailhop.org" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1754873Ab3FLROK (ORCPT ); Wed, 12 Jun 2013 13:14:10 -0400 Content-Disposition: inline In-Reply-To: <20130612163124.GD8164@atomide.com> Sender: linux-omap-owner@vger.kernel.org List-Id: linux-omap@vger.kernel.org To: Ming Lei , Sricharan R Cc: linux-arm-kernel@lists.infradead.org, linux-omap@vger.kernel.org * Tony Lindgren [130612 09:37]: > * Ming Lei [130603 08:34]: > > Hi, > > > > On Sat, May 18, 2013 at 3:17 AM, Tony Lindgren wrote: > > > We can now boot with device tree. If you don't want to update u-boot, > > > you can boot with appended DTB with the following instructions: > > > > > > 1. Make sure you have the appended DTB support in .config > > > > > > CONFIG_ARM_APPENDED_DTB=y > > > CONFIG_ARM_ATAG_DTB_COMPAT=y > > > CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y > > > > > > 2. Build the zImage > > > > > > $ ARCH=arm CROSS_COMPILE=... make zImage > > > > > > 3. Build the device tree blobs > > > > > > $ ARCH=arm CROSS_COMPILE=... make dtbs > > > > > > 4. Append the correct panda dtb to zImage > > > > > > Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb > > > or omap4-panda-es.dtb. > > > > > > $ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended > > > > > > 5. Use mkimage to produce the appended device tree uImage > > > > > > $ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \ > > > -n "Linux" -d /tmp/appended /tmp/uImage > > > > I followed the above steps and tried devicetree on Pandaboard against > > 3.10.0-rc3-next-20130528, and the board will hang during boot, but works > > well with legacy mode. > > > > Hardware: Pandaboard A1 > > dtb: omap4-panda.dtb > > > > See 'dmesg' on below link: > > > > http://kernel.ubuntu.com/~ming/up/panda-dts.dmesg > > > > Hmm looks like it boots to init. Maybe add initcall_debug to the cmdline in > case there's some late_initcall that causes the issue. It's probably some > trivial issue causing it. Sricharan, maybe give this a quick try if you have the original pandaboard? I only have pandaboard es. Regards, Tony From mboxrd@z Thu Jan 1 00:00:00 1970 From: tony@atomide.com (Tony Lindgren) Date: Wed, 12 Jun 2013 10:14:08 -0700 Subject: [PATCH 2/6] ARM: OMAP2+: Remove board-omap4panda.c In-Reply-To: <20130612163124.GD8164@atomide.com> References: <20130517191304.468.73487.stgit@localhost> <20130517191753.468.1734.stgit@localhost> <20130612163124.GD8164@atomide.com> Message-ID: <20130612171407.GM8164@atomide.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org * Tony Lindgren [130612 09:37]: > * Ming Lei [130603 08:34]: > > Hi, > > > > On Sat, May 18, 2013 at 3:17 AM, Tony Lindgren wrote: > > > We can now boot with device tree. If you don't want to update u-boot, > > > you can boot with appended DTB with the following instructions: > > > > > > 1. Make sure you have the appended DTB support in .config > > > > > > CONFIG_ARM_APPENDED_DTB=y > > > CONFIG_ARM_ATAG_DTB_COMPAT=y > > > CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND=y > > > > > > 2. Build the zImage > > > > > > $ ARCH=arm CROSS_COMPILE=... make zImage > > > > > > 3. Build the device tree blobs > > > > > > $ ARCH=arm CROSS_COMPILE=... make dtbs > > > > > > 4. Append the correct panda dtb to zImage > > > > > > Depending on your hardware it's omap4-panda.dtb, omap4-panda-a4.dtb > > > or omap4-panda-es.dtb. > > > > > > $ cat arch/arm/boot/zImage arch/arm/boot/dts/omap4-panda-es.dtb > /tmp/appended > > > > > > 5. Use mkimage to produce the appended device tree uImage > > > > > > $ mkimage -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 \ > > > -n "Linux" -d /tmp/appended /tmp/uImage > > > > I followed the above steps and tried devicetree on Pandaboard against > > 3.10.0-rc3-next-20130528, and the board will hang during boot, but works > > well with legacy mode. > > > > Hardware: Pandaboard A1 > > dtb: omap4-panda.dtb > > > > See 'dmesg' on below link: > > > > http://kernel.ubuntu.com/~ming/up/panda-dts.dmesg > > > > Hmm looks like it boots to init. Maybe add initcall_debug to the cmdline in > case there's some late_initcall that causes the issue. It's probably some > trivial issue causing it. Sricharan, maybe give this a quick try if you have the original pandaboard? I only have pandaboard es. Regards, Tony